Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Metal decking
Arval Globalfloor Cofraplus 220 cold rolled steel decking for steel composite floors
Panel reference
Arval Cofraplus
Manufacturer
ArcelorMittal
Immeuble Innovatis, 1-5 rue Luigi Cherubini
La Plaine Saint Denis Cedex 93212
FRANCE
web site: www.arcelormittal.com/arval
H005
H006
H007
H008
H003
H009
H012
H004
Standard end abutment
H011
H004
H010
H006
H007
H008
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
1.00mm; 1.13mm & 1.25mm as required to suit load/span requirements of the design
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
220
80
50
584.5
340
390
750
70 Min
Mesh
Line of steelwork
Side laps stitched at 350mm centres including trough shear-bond clip
End diaphragms required to each concrete deck at steelwork interface
Line of steelwork
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
50 Nominal
220
35x35 square
stiffening tube
Slimfloor connector
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
50 Nominal
35x35 square
stiffening tube
220
Slimfloor connector
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
220
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
220
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
Restraint straps fixed at 500mm centres
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
220
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
Restraint straps fixed at 500mm centres
50 Nominal
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
220
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
Dowel bars through beam web
(to create composite beam)
@ 750mm c/c - please consult our
Technical Department for details
50 Nominal
35x35 square
stiffening tube
Slimfloor connector
35x35 square
stiffening tube
Slimfloor connector
50 Nominal
220
220
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
35x35 square
stiffening tube
Slimfloor connector
35x35 square
stiffening tube
220
50 Nominal
220
Slimfloor connector
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and mulyi-spans are possible (please consult our Technical
department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
220
Additonal support angle (1.2mm min) where hole size exceeds 500mm
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Material
Nominal thickness
Soffit finish
Plain galvanized steel (Z275) to EN10169-3 or Colorissme to standard colour chart is available
on request - please consult our Technical Department
End bearing
Edge bearing
Sealing laps
Configuration
Mainly single span. In some cases cantilever and multi-spans are possible (please consult our Technical
Department)
Attachment
As clause 280
Accessories
Shear connectors, end & edge closers (1.2mm to 1.5mm), steel wings (3.0mm) flashings, filler blocks etc
Anti-crack mesh
220
220
50
50
220
55
40
Anti-crack mesh
15 max
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)
Check that the structure is in a suitable state to receive the decking before commencing fixing.
Subcontractor must confirm acceptance to Main Contractor and CA.
Of a type recommended for the purpose by decking manufacturer. Apply to interfaces between
dissimilar metals & support connectors and decking profile which would otherwise be in contact.
Provided by ArcelorMittal Construction to accurately match decking profile. Length of fillers are equal to
width of supports unless specified otherwise. Fill every profile above specified supports, bonding into
position with adhesive recommended by ArcelorMittal Construction.
Cut sheets to give clean, true lines with no distortion and without damage to any protective coating.
Remove burrs and any lubricant. Cut openings in sheets for outlets, vent pipes, flues, etc.to the minimum
size necessary and at locations of minimum stress in service. Reinforce edges of openings with stiffening
patch, pressed steel angles or structural trimmers depending on size of opening. Drill all holes. Remove all
drilling swarf, dust and any other foreign matter before placing any membranes or insulation. Protect
sheets during fixing and up to Practical Completion against mechanical damage, corrosion and
disfigurement. Rectify any defects as quickly as possible to minimise damage and nuisance. Place
temporary support props with AMCsupport templates (returnavle after use) on suitable base supports to
spacing required by design. Ensure props are tight to u/s of decking but not over tightened so as to deform
bottom trough of deck and cross brace if required. Fix decking to beam support or wings with HILTI
X-ENP19 L15 shot fired nails or stitcher screws generally at 750mm centres.
280 Attachment
282 Attachment
The method of attachment of the metal profiled sheet decking floor and accessories must be sufficient
to resist the wind loads applied to the floor before pouring the concrete in accordance with
BS EN1991-1-4:2005 & A1:2010
283 Attachment
For Slimfloor connstruction pre-drill webs of support beams at 750mm c/c to receive reinforcing dowel
bars to design requirements (please consult our Technical Department for diameters & lengths of
dowels).
R
Note: The provision of fire resistance reinforcement is not covered by this document. Please consult our
Technical Department for requirements.
Material: Galvanised steel thickness/gauge: 1.2mm for connectors with stiffening tubes & 1.5mm for plain
connectors. 3.0mm galvanized steel AMC wings. Finish/Colour to match steel decking profile.
(Note: All installations should comply with the recommendations contained in MCRMA Techinical Papers N 12 & 14; BS3200 and other relevant national standards)