Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Page 1 of 18
55-32
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 2 of 18
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 3 of 18
55-33
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 4 of 18
55-34
Tailgate, adjusting
Note:
Before installing a new tailgate the gas-filled
struts must be installed.
- Loosely attach striker -1- with nuts -2-.
- Loosely attach lower stop -1- (on trim of rear hatch) using hex bolt -2-.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 5 of 18
55-35
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 6 of 18
55-36
- Loosen hex bolt -2- and pull lower stop -1- out slightly.
- Tighten hex bolt -2- slightly and close rear hatch.
- Using sensor gauge, set stop -1- from inside at 1 mm clearance to
tailgate trim.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 7 of 18
55-37
CAUTION!
Stop buffers must not make contact with rear
lid trim when rear lid is closed.
- Open hatch and tighten hex bolt -2- for stop to 8 Nm (71 in. lb).
- Check gap dimensions
page 55-41 .
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 8 of 18
55-38
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 9 of 18
55-39
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 10 of 18
55-40
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 11 of 18
55-41
4.0 +1
0.5
-B-
5.0 +1
-C-
4.0 +1
0.5
-D-
3.4 +1
0.5
-E-
3.4 +1
0.5
-F-
5.0+1
-G-
1.0
-H-
2.5
0.1
-I-
3.3
0.1
-J-
3.3
0.2
-K-
3.0
0.4
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 12 of 18
55-42
page 55-43
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
page 55-44
11/20/2002
Page 13 of 18
55-43
page 55-
- Remove hex bolts (arrow) and remove lock system from tailgate.
Hex bolt tightening torque: 8 Nm (71 in. lb)
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 14 of 18
55-44
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 15 of 18
55-45
page 55-32
5 - Lock mechanism
- To remove, remove hex bolts -1-.
- Disengage locating hooks on release
handle ( Fig. 1 ) and remove.
- Remove lock mechanism.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 16 of 18
55-46
6 - Grip piece
- Before removal, remove tailgate trim.
Repair Manual, Body-Interior, Repair Group 70
- To remove, remove hex nuts -1- and
bolts -3-.
- Pull grip piece slightly out of tailgate and
disconnect harness connectors for
license plate lights.
- To install, insert grip piece into tailgate
holes.
- Thread bracket -2- at lock mechanism
and attach to grip piece using external
securing screws.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 17 of 18
55-47
Fig. 1
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002
Page 18 of 18
55-48
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.BD01.55.4
11/20/2002