Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
PTI-255W
VL-Bus Super ,{/O Card
User's Guide
Version 1.01
FEATURES
This device complies with Part 15 of the FCC Rules. Operationis subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. Shielded interference cable(s) must be used according to
FCC 15.27.
CARDLAYOUT
The illustration below will familiarize the user with the layout of the PTI-255W
VL-Bus super 110 card and its onboard ports.
HARD DISK
CONNCCTCJIt 1
rLDPPY DISI(
CDlKCTtJt
PARALLEL
PRINTER
PORT
Fig 1 YfI-255W
Jl
JP2-1 .7
JP1-1,6,11
reo .11
:~
"~
ENABLED
(DEFAULT)
12~
7. ,.
10
DISABLED
13~
8 "
CPU SPEED
50MHz
(DEFAULT)
(DEFAULT}
roo
JP2-3,S,8
AleB C!i'.NG
,_}~
600ns
(DEFAULT)
4005
':I~~
':I~~
I
I
Jro-3f7
{DEF"""'T}
37(}-J77
CONTROLLER
JP3
IDEl
8r......::.
I/o
I[)EO I/o
ENABLED
DISALBED
(DEFAULT)
CHANNEL READY
ENABLED
(DEFAULT)
CLOSE
OPEN
DIS'JlLED
Setting
JP4
CHANNEL READY
CLOSE
EN-'BLD
(DEFAULT)
JPl-4.9,1\
5,10,1
30
JP2-2.5,~
IFO PORT
'~~
1 "
JPl-3,8,13
20
1~~
YODE
NORtJAL
,0
6 ~"":
Cl4AHG(
JPl-2,7,12
DI SALB ED
OPEN
500ns
'~~
33MHz
400ns
40
l!lli~
. '.~
Setting
.ceo ..)
1;1~+
1;1~4
1~.~4
2 (CO )
COt.l2 (2FBH)
(DEFAlA.T)
004
COM+ (26H)
1.16
9
DIS>.BLED
COIAJ (3EBH)
COt.43(3E8H)
10
+
1
1
15
9
J
JP5-5,11.17
6.12.18
'.18
DIS>.BLED
12
DISABLED
a
11
15
1
1
lIB
17
COlA4 (2EBH)
~BB~o
LPn (37811)
(DEF.oJJLT)
006
16
PARALLEL PORT
12
II
17
16
10
o.
15
sr.PO'"
JP5-H~.16
11302
User may move up to a higher speed level after extensive disk reading and writing
tests. However, it is recommended to use the default speed when the hard disk drive
is initially installed.
COOl (3FBH)
(DEFAlA.T)
10
10
SDI .. PORT
'
240ns
Setting
12
18
l.PTJ (38CH)
06
18
l.PT2 (278H)
'~BB~2
Port Jumper
Setting
Setting
HARDDISK INSTALLATION
PRINTER PORT
JP6
fJ
(1)
~61POll)
FAVLT
CLOSE
I/O PORT
OPEN
Port Jumper
Setting
Case B:
JP7 -- This jumper select Parallel Port IRQ Jumper Setting as follow:
JP6
2~4
1
PARALLEL
PORT
IRQ
(2)
IRQ7
(DEFAULT)
m;
2 Drives System:
Case A:
Sets Drive C: to Master; and Drive D: to slave and
connects both drives on IDE 0 connector. Sets Drives C:
and D: disk parameters in CMOS.
IRQ5
4 Drives System:
Sets Drive C: to Master; and Drive D: to slave, and connects both drives
on IDE 0 connector. Sets Drive E: to Master; and Drive F: to slave and
connects both drives on IDE 1 connector.
Sets Drives C: and D: disk
parameters in CMOS.
GAME
(1)
Install the PTI-2SSW, the IDE drives, the floppy drives and the LED
Firstly, plug the PTI-255W into a 32-bit VL-Bus slot. Secondly, properly
connect the IDE cable to the IDE drive connector and to the IDE drive(s).
Thirdly, properly connect the floppy cable to floppy drive connector and to
the floppy drive(s). Both cables should have the coloured bands on the
cable to indicate the pin 1 position.
(2)
(3)
PORT
ENABLED
(DEFAULT)
CLOSE
DISABLED
OPEN
Setting