Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Introduction
PT. Tri Panji Puring (known as TPP) is a multidisciplinary
engineering company. Its range of services encompasses
projects in the oil and gas industry at both onshore and
offshore locations. TPP provides cost effective engineering
design, procurement and construction services specifically
tailored for our clients needs.
The companys capabilities range from feasibility studies,
Feed, As-built Survey, detail design engineering,
Independent Appraisal/ Asseessment and operational
documentation.
Companys Capabilities
Detailed Engineering
and Drawing Services
TPP
Equipment and
Facility Assessment
As Built Survey
Companys Particulars
Company Name
Office Adrress
Telephone
021-70993909
Facsimile
021-70993909
Email Address
info@tripanjipuring.com
Notaries Document
No. 03
AHU-24155.AH.01.01.Tahun 2009
PEM-00634/WPJ.06/KP.0603/2011
02.836.578.1-024.000
Director
IR. LISBETH
Assessment Proposal
Scope
SUPPORTING DECREE
SKPP
Pressure Vessel
Pressure Safety Valve
Pump & Compressor
Generator
Switchgear
Transformer
Motor Control Center
Crane
Tank
Pipeline
SAFETY
HAZID/HAZOP
Safety Integrated Level (SIL)
Safety Management System
(SMS)
NON SKPP
Piping System
Instrumentation & Control
System
Civil Works
Electrical System
Mechanical System
Safety Protection System
Environmental Protection System
ENVIRONMENTAL
AMDAL/RKL/RPL Certificate
AMDAL/RPL/RKL Document
PRE--COMM/COMM
PRE
Loop/Sequence Test
Pressure/Leak Test
Calibration
Megger Test
Continuity Test
Motor Sequence Test
Alignment Test
Tank Water Filling Test
Function Test
OTHER PERMITS
Steam Boiler/Generator
Helipad
Metering/Tank Calibration
Explosive
Combo Dock/Jetty
Methodologhy
Process Safety and Risk Assessment FSO
Managed by
Classification society
(e.g. ABS, BKI, BV etc.)
Managed by risk
assessment
Methodologhy
Preliminary study, document collection,
preliminary discussion with Client/Migas
Migas rule:
Kepmen,Kepdirjen
,Kepdir
Adopted
Codes,Recommended
Practices, Standards
NOT
OK
Revise
Submit Report
OK
Final Report to Client
NOT
Clarification &
Discussion with Client
Revise
Assessment
PRESSURE VESSEL
General condition check by visual inspection
Conduct thickness verification and
measurement
Verify as-built drawing as per the dimensional
check result, wall thickness gauging, material
identification and parts completion check.
Determine minimum thickness required are
used the actual thickness.
Mechanical integrity evaluation for pressure
vessel
Assessment
ROTATING EQUIPMENT
General condition check by visual inspection
Determine the design parameter (suction
pressure & temperature, discharge pressure &
temperature, flow rate) and operation
parameter of pump
Determine the specification, design parameter
and operation parameter of prime mover
Mechanical integrity evaluation for rotating
equipment
Assessment
ELECTRICAL EQUIPMENT
General condition check by visual inspection
Determine the design parameter and operation
parameter of electrical equipment (MCC,
Switchgear, Generator, Transformer)
Determine the specification, design parameter
and operation parameter of prime mover
Mechanical integrity evaluation for electrical
equipment
Assessment
Assessment
Communication Plan
Project Manager
JANTER NS
QHSE
BENNY
Lead Engineer
RANTINO
RONI
Selected Experiences
Assessment Equipment and Facilities
Selected Experiences
Selected Experiences
Risk Assessment Analyses
Selected Experiences
THANK YOU
Office :
Jl. Pulo Raya IV No.26
Kebayoran Baru, Jakarta Selatan
Tlp : 021-70993909
e-mail : info@tripanjipuring.com
Contact Person : Dian Budi Dharma
(Bussiness Development Manager)
Mobile +6287889197484