Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Service Guide
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate Victoria service guide.
Date
II
Chapter
Updates
Copyright
Copyright 2007 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
NOTE
WARNING
CAUTION
IMPORTANT
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
VI
Chapter 1
System Specifications
Features
Below is a brief summary of the computers many feature:
Operating system
T
Genuine Windows VistaTM Home Basic / Home Premium / Ultimate / Business Edition
NOTE: Windows VistaTM Capable PCs come with Windows XP installed, and can be upgraded to
Windows VistaTM. For more information on Windows VistaTM and how to upgrade, go to:
Microsoft.com/windowsvista.
T
T
12.1 WXGA+ high-brightness Acer CrystalBriteTM TFT LCD, 1680 x 1050 pixel resolution, 6 lamps
Audio
Chapter 1
Built-in microphone
Storage subsystem
T
One or two 80/100/120 GB Serial ATA hard disk drive, supporting software RAID 0/1
5-in-1 card reader, supporting Secure Digital (SD), MultiMediaCard (MMC), Memory Stick (MS),
Memory Stick PROTM (MS PRO), xD-Picture CardTM (xD)
Input devices
T
Communication
T
Acer Video Conference, featuring Voice and Video over Internet Protocol (VVoIP) support via Acer
OrbiCamTM and optional Acer Bluetooth VoIP phone
Modem: 56K ITU V.92 modem with PTT approval; wake-on ring ready
I/O Ports
Microphone-in jack
Line-in jack
Chapter 1
Environment
T
Temperature:
t Operating: 5C to 35C
t Non-operating: -20C to 65C
Humidity (non-condensing):
t Operating: 20%~80%
t Non-operating: 20%~80%
Chapter 1
Chapter 1
Board Layout
Top View
4 5
6
7
3
10
8 9
11
13
12
15
14
17
16
18
19
20 21 22 23 24
CN21
CN20
U26
CN18
CN17
S-Video Connector
17
U33
PJ1
DC-in Jack
18
U34
CN19
Ethernet Controller
19
CN28
CN24
DIMM Socket
20
CN23
Line-in Jack
CN25
DIMM Socket
21
CN29
Microphone-in Jack
10
CN23
Fan Connector
22
CN31
Headphones/Speaker/Line-out
Jack
11
U29
North Bridge
23
CN30
12
U30
CPU Socket
24
J40
Infrad Sensor
Chapter 1
13
CN26
14
U32
South Bridge
15
CN27
16
U39
Audio Codec
Bottom View
6
7
4
5
8
10
9
11
14
15
12
13
16
18
19
17
CN1
11
CN11
CN2
LCD Connector
12
U17
USB Connector
CN3
13
CN4
14
CN8
Touchpad Connector
(Fingerprinter to Main Board)
CN5
Bluetooth Connector
15
CN9
Fingerprinter Connector
U3
16
PU6
PU3
17
CN16
Speaker Connector
U10
18
CN14
U14
19
CN15
10
CN7
Keyboard Connector
Chapter 1
Front View
Chapter 1
Icon
Item
Description
Built-in camera
Microphone
Status indicators
Power button
Empowering button
Keyboard
Touchpad
Fingerprinter
10
Display screen
11
Wireless communication
button/indicator
12
Bluetooth
communication button/
indicator
13
Easy-launch buttons
14
Palmrest
Icon
Item
Description
Speaker
Power indicator
Battery indicator
Infrared port
Line-in jack
Microphone-in jack
Headphones/speaker/
line-out jack with S/PDIF
support
Chapter 1
Left View
Icon
Item
Description
Ethernet (RJ-45)
Ventilation slots
PC Card slot
Right View
Chapter 1
Icon
Item
Description
Optical drive
Connects to a Kensington-compatible
computer security lock.
Rear view
10
Icon
Item
Description
External display
(VGA) port
S-video/TV-out
(NTSC/PAL) port
DC-in jack
Connects to an AC adapter.
Chapter 1
Base view
Item
Description
Battery bay
Battery lock
Memory compartment
Indicators
The computer has several easy-to-read status indicators.
The front panel indicators are visible even when the computer cover is closed up.
Chapter 1
11
Icon
Function
Description
HDD
Num lock
Cap lock
Power
Battery
Bluetooth
Wireless LAN
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Easy-Launch Buttons
To the right of the keyboard there are three easy-launch buttons: Web browser, mail, and one userprogrammable button. You can also find an Empowering Key
Press
to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email
and Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons,
run the Acer Launch Manager.
12
Chapter 1
Launch key
Default application
Acer Empowering Technology (user-programmable)
Web browser
User-programmable
Touchpad Basics
The following teaches you how to use the touchpad:
Move your finger across the touchpad (2) to move the cursor.
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button.
Use the fingerprinter (3) to enroll the computer with registered fingerprint. This recognition device
helps prevent unauthorized access by others.
Function
Execute
Select
Click once
Tap once
Drag
Access context
menu
Log in with
authorized
fingerprint
Fingerprinter (3)
Click once
Swipe your finger
over the
fingerprinter.
NOTE: When using the touchpad, keep it - and your fingers - dry and clean. The touchpad is sensitive to finger
movements; hence, the lighter the touch, the better the response. Tapping too hard will not increase the
touchpads responsiveness.
Chapter 1
13
Lock Key
Description
Caps Lock
Num lock
<Fn>+<F11>
Scroll lock
<Fn>+<F12>
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
Num Lock On
Cursor-control keys on
embedded keypad
Windows Keys
The keyboard has one key that performs Windows-specific functions.
14
Chapter 1
Key
Icon
Windows key
Description
Pressed alone, this key has the same effect as
clicking on the Windows Start button; it launches the
Start menu. It can also be used with other keys to
provide a variety of function:
+ <Tab> Activates next taskbar button.
+ <E> Opens the My Computer window
+ <F1> Opens Help and Support.
+ <F> Opens the Search: All Files dialog box.
+ <R> Opens the Run dialog box.
+ <M> Minimizes all windows.
<Shift>+
action.
Application key
Hot Keys
The computer employs hotkeys or key combinations to access most of the computers controls like screen
brightness, volume output, and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hot Key
Icon
Function
Description
<Fn>+<F1>
<Fn>+<F2>
Acer eSettings
<Fn>+<F3>
Acer ePower
Management
<Fn>+<F4>
Sleep
Chapter 1
15
Hot Key
Icon
Function
Description
<Fn>+<F5>
Display toggle
<Fn>+<F6>
Screen blank
<Fn>+<F7>
Touchpad toggle
<Fn>+<F8>
Speaker toggle
<Fn>+<w>
Volume up
<Fn>+<y>
Volume down
<Fn>+<-x>
Brightness up
<Fn>+<z>
Brightness down
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center of your keyboard.
To type:
Gr
2.
Hold <Alt Gr> and then press the <5> symbol at the upper-center of the keyboard.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
16
Chapter 1
Chapter 1
17
Acer eNet Management can save network settings for a location to a profile, and automatically switch to the
appropriate profile when you move from one location to another. Settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings.
Security and safety concerns mean that Acer eNet Management does not store username and password
information.
18
Chapter 1
2.
3.
Select one of the predefined power plan that is closest to what you want.
4.
5.
6.
Chapter 1
19
Battery status
For real-time battery life estimates based on current usage, refer to the time shown in the Remaining Battery
Life field.
20
Chapter 1
Chapter 1
21
22
Chapter 1
T
T
T
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
Optical drive devices - includes any kind of CD-ROM or DVD-ROM drives.
Floppy disk drives - 3.5-inch disks only.
Interfaces - includes serial ports, parallel port, infrared (IR), and Bluetooth.
To activate Acer eLock Management, a password must be set first. Once set, you can apply locks to any of the
devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked after rebooting,
until unlocked.
NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to an Acer Customer Service Center. Be sure to remember or write down your password.
Chapter 1
23
Password protection.
Recovery of applications and drivers.
Image/data backup:
T
T
Back up to CD/DVD.
Image/data recovery tools:
T
24
Chapter 1
Chapter 1
25
No.
1
Item
Lens
Power indicator
26
Chapter 1
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start > All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:
1.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2.
3.
Chapter 1
27
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Launch Manager
Launch Manager allows you to set the four easy-launch buttons (see their locations mentioned in EasyLaunch Buttons). You can access the Launch Manager by clicking Start > All Programs > Launch Manager to
start the application.
28
Chapter 1
Specification
CPU type
Core logic
CPU package
0.944~1.3V
TM
Fan Speed
Acoustic Level
Core 0
Core 1
(rpm)
(dBA)
86
86
3700
39
88
88
3450
36.5
91
91
3150
34.5
95
95
2800
31
BIOS
Item
BIOS vendor
Specification
Phoenix
BIOS Version
BIOS ROM type
Flash ROM
512KB
BIOS package
32-pin PLCC
Supported protocols
NOTE: If you need to check PXE version, press F2 to enter BIOS then enable boot from LAN function. After
that, power off the system and remove the HDD. Last, reboot the laptop. Then you will see PXE version
displaying on the screen.
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
2MB
Always enabled
Always enabled
Fixed in write-back
Chapter 1
29
System Memory
Item
Specification
Memory controller
Memory size
2 sockets
2GB
667 MHz
200-pin soDIMM
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
128MB
128MB
0MB
256MB
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
128MB
128MB
256MB
128MB
256MB
384MB
128MB
512MB
640MB
128MB
1024MB
1152MB
128MB
2048MB
2176MB
256MB
128MB
384MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
256MB
2048MB
2304MB
512MB
128MB
640MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
128MB
1152MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
30
Chapter 1
LAN Interface
Item
Specification
Chipset
Broadcom 5787
10/100/1000 Ethernet
Giga LAN
RJ45
Left side
Features
Modem Interface
Item
Specification
56K
V.92
RJ11
Right side
Bluetooth Interface
Item
Chipset
Specification
Built-in ICH7-M
Data throughput
Protocol
Interface
USB 1.1
Connector type
USB
Specification
Intel 4965
Data throughput
11~54 Mbps
Protocol
802.11a+b+g+n
Interface
PCI
Seagate ST96812A
Seagate ST960821A
Toshiba MK6025GAS
HGST HTS541260H9AT00
WD WD600UE-22HCT0
TOSHIBA MK8025GAS
HITACHI HTS421280H9AT00
SEAGATE ST9808210A
SEAGATE ST98823A
TOSHIBA MK8026GAX
HGST HTS541280H9AT00
WD WD800UE-22HCT0
Capacity (MB)
40000
60000
80000
Bytes per
sector
512
512
512
Data heads
4 (for Hitachi)
3 (for Seagate)
Drive Format
Chapter 1
31
Spindle speed
(RPM)
4200 RPM
4200 RPM
4200 RPM
Performance Specifications
Buffer size
2048KB
8192KB
8192KB
Interface
ATA/ATAPI-6; ATA-6
ATA/ATAPI-6; ATA-6
ATA/ATA-6; ATA-6
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
372
350
350
Data transfer
rate
(host~buffer,
Mbytes/s)
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Voltage
tolerance
5V(DC) +/- 5%
DVD-Dual Interface
Item
Specification
LITEON SOSW-833S
PIONEER DVR-K16RA
Performance Specification
With CD Diskette
Sustained:
Max 3.6Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Buffer Memory
2MB
Interface
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
32
Specification
Audio Controller
Realtek ALC268
Built-in
Mono or Stereo
Stereo
Chapter 1
Audio Interface
Item
Specification
Resolution
Compatibility
Sampling rate
Internal microphone
Yes
Yes/2(1.5W speakers)
DMA channel 0
DMA channel 1
IRQ10, IRQ11
USB Port
Item
Specification
Chipset
Built-in ICH8M
2.0
OHCI
Location
PCMCIA Port
Item
Specification
PCMCIA controller
TI PCI 7412
Type-II
Number of slots
One type-II
Access location
Left side
No ZV support
Yes
Controller
Intel 965GM+ICH8M
LAN
Broadcom 5787
USB 2.0
Built in ICH8M
NS 87383
MODEM
Built-in ICH7-M
Bluetooth
Built-in ICH7-M
Intel 4965
PCMCIA
TI PCI 7412
Audio
Realtek ALC268
Keyboard
Item
Specification
Keyboard controller
KBC1122
88-/89-key
Chapter 1
33
Keyboard
Item
Specification
Yes
Battery
Item
Specification
Battery Type
Li-ion
Pack capacity
4800 mAH
Package configuration
Normal voltage
14.8V
Charge voltage
16.8+-0.2v
Specification
SAMSUNG
LTN190-M2000 NONGLARE
SAMSUNG
LTM190-M2L01-G GLARE
TYPE
19.1 inches
19.1 inches
19.1 inches
19.1 inches
304.1x228.1
304.1x228.1
304.1x228.1
1440x900
WXGA+
1440x900
WXGA+
1440x900
WXGA+
Pixel Pitch
0.297x0.297
0.099x0.297
0.297x0.297
Pixel Arrangement
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
Display Mode
Typical White Luminance
(cd/m2)
1440x900
WXGA+
R.G.B. Vertical
Stripe
Normally White
Normally White
Normally White
Normally White
300
300
300
300
N/A
N/A
70
70
34
Contrast Ratio
300
300
250
250
+3.3V Typ.
+3.3V
3.3V
3.3V
5.6/5.7
3.96
N/A
N/A
Weight
550
570
600
600
Physical Size(mm)
317.3x242.0x6.
0
317.3x242.0x5.
9
317.3x242.0x6.
5
317.3x242.0x6.
5
Electrical Interface
1 channel LVDS
1 channel LVDS
1 channel LVDS
1 channel LVDS
Support Color
262K colors
(RGB 6-bit data
driver)
262,144
262,144
262,144
Chapter 1
Specification
40/40
45/45
40/40
40/40
Vertical: Upper/Lower
10/30
15/35
20/40
20/40
0 to +50
0 to +50
0 to +50
0 to +50
-20 to +60
-25 to +60
-20 to +60
-20 to +60
Temperature Range( C)
Operating
Storage (shipping)
LCD Inverter
Item
Specification
Darfon/V189-301GP
Brightness conditions
N/A
9~21
2.56 (max)
6.5 (max)
65K Hz (max)
AC Adaptor
Item
Specification
Input rating
1.7A
Inrush current
220A@115VAC
220A@230VAC
Efficiency
Power Management
Working (G0/S0)
Individual devices such as the CPU and hard disc may be power
managed in this state.
Also called Hibernation Mode. System saves all system states and
data onto the disc prior to power off the whole system.
Chapter 1
35
36
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computers BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when Press <F2> to enter Setup message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to disabled. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to enabled.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Main
Advanced
Security
CPU Type :
CPU Speed :
Hitachi HTS541612J9SA00
xxxxxxxxxxxxxxxxxxxxxx
HL-DT-ST DVDRAM GSA-T20N
v0.3101
SentaRosa 1436
xxxxxxxxxxxxxxxxxxxxxx
Boot
Exit
T7300 @ 2.00GHz
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
Select Item
F9 Setup Defaults
Esc Exit
Select Menu
Enter Select
Chapter 2
Sub-Menu
37
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
Press ^ while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
38
Chapter 2
Information
Phoenix TrustedCore(tm) Setup Utility
Information
Main
Advanced
Security
Boot
CPU Type :
CPU Speed :
Hitachi HTS541612J9SA00
xxxxxxxxxxxxxxxxxxxxxx
HL-DT-ST DVDRAM GSA-T20N
v0.3101
SentaRosa 1436
xxxxxxxxxxxxxxxxxxxxxx
Exit
T7300 @ 2.00GHz
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
Select Item
F9 Setup Defaults
Esc Exit
Select Menu
Enter Select
Sub-Menu
Parameter
CPU Type / CPU Speed
Description
This field shows the CPU type and speed of the system.
This field shows the model name of HDD installed on primary IDE master.
This field displays the serial number of HDD installed on primary IDE master.
Serial Number
Product Name
Manufacturer Name
UUID Number
Chapter 2
39
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
A d va n ce d
Main
S e c u rity
B oot
E x it
Time:
[19:03: 49]
System
Date :
[04/25/ 2007]
System Me
mory :
Ex tended Memory
Video Memory
Quiet Boot :
Power On Display
Network Boot :
F12 Boot Menu :
D2D Recovery :
:
:
640 KB
Shows system
1014 MB
[8MB ]
AHCI Configuration
F1
<Tab>, <Shift-Tab>, or
<Enter> selects field.
base memory size
[Enabled]
[Auto]
[Enabled]
[Disabled]
[Enabled]
: [Enabled]
H e lp
S e le c t Ite m
F5/F6
C h a n g e V a lu e s
F9
Esc E x it
Se lect Menu
Enter
Se lect
Sub -Menu
Se tup Defaul ts
NOTE: The screen above is for your reference only. Actual values may differ.
40
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
System Memory
Extended Memory
Video Memory
Quiet Boot
D2D Recovery
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
41
Advanced
The Advanced screen displays advanced settings in BIOS.
Main
Advanced
Security
Boot
Exit
Serial Port :
[Auto]
Parallel Port :
Mode :
[Auto]
[ECP]
Infrared Port(FIR) :
[Auto]
[Disabled]
No configuration
ASF Configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when
controlled by OS
F1 Help
Select Item
F9 Setup Defaults
Esc Exit
Select Menu
Enter Select
Sub-Menu
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Serial port
42
Description
Option
Parallel port
IrDA Device
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Main
Security
Advanced
Boot
Exit
Clear
Clear
Clear
[Enter]
[Enter]
[Enter]
Password on boot :
[Disabled]
Supervisor Password
controls accesses to the
setup utility.
F1 Help
Select Item
F9 Setup Defaults
Esc Exit
Select Menu
Enter Select
Chapter 2
Sub-Menu
43
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password is
Clear or Set
User Password is
Clear or Set
Clear or Set
Password on Boot
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Dont forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the supervisor, user, or hard disk password:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type a password in the Enter New Password field. The password length can not exceed 8 alphanumeric
characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.
IMPORTANT: Be very careful when typing your password because the characters do not appear on the
screen.
44
3.
Press e. After setting the password, the computer sets the Supervisor Password parameter to Set.
4.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to Clear.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the Supervisor Password parameter to Set.
5.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
45
If the new password and confirm new password strings do not match, the screen will display the following
message.
46
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the diskette drive in module bay, the onboard hard disk drive, and the CD-ROM in module bay.
Main
Boot
Security
Exit
F1
Help
Esc Exit
Chapter 2
Select Item
F9 Setup Defaults
Select Menu
Enter Select
Sub-Menu
47
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Main
Advanced
Security
Exit
Boot
F1
Help
Esc Exit
Select Item
F9 Setup Defaults
Select Menu
Enter Select
Sub-Menu
Parameter
48
Description
Discard Changes
Save Changes
Chapter 2
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Follow the steps below to run the Phlash.
1.
2.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
49
50
Chapter 2
Chapter 3
Wrist grounding strap and conductive mat for preventing electrostatic discharge
Philips screwdriver
T
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
Chapter 3
51
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
52
1.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Chapter 3
Start
Battery Pack
D*5
F*1
Thermal
Door
B*1
D*1
System Fan
F*1
F*2
Mimi Cover
HDD Door
F*1
H*4
ODD Module
Memory
HDD Bracket
HDD
B*4
Thermal
Module
Middle Cover
F*2
CPU
Keyboard
C*2 LCD hinges to logic
D*2 LCD hinges to logic
C*2 on bottom side
LCD Module
C*8 upper case assembly to lower case assembly on bottom side
C*2 upper case assembly to lower case assembly on upper side
Lower Case
Assembly
Upper Case
Assembly
F*1
F*2
Switch Board
(for AS
models)
Modem
Board
F*1
Media Board
(for AS
models)
Touchpad
Bracket
F*1
Main Board
Touchpad
Touchpad
FFC
F*2
Lower Case
Chapter 3
Speaker Set
53
LCD Module
B*4
LCD Bezel
G*1 for 15"
G*2 for 15.4"
LCD Inverter
B*2
LCD
Assembly
LCD Panel
Wireless
Antenna Set
LCD Cable
LCD
Screw List
Item
A
54
Description
Part Number
SCREW M2.5*3(NL)
86.TAVV5.001
SCREW M2.5*6(NL)
86.TAVV5.002
SCREW M2.5*10(NL)
86.TAVV5.003
SCREW M2.5*15(NL)
86.TAVV5.004
SCREW M2*2.2
86.TAVV5.005
SCREW M2*3(NL)
86.TAVV5.006
SCREW M2*4
86.TAVV5.007
SCREW M3*4(NL)
86.TAVV5.008
86.TAVV5.009
Chapter 3
Unlock the battery lock (move the battery lock to the right).
2.
Chapter 3
55
2.
56
3.
4.
5.
Pop out the memory from the DIMM socket then remove it (If the notebook has two memory, then repeat
this step).
6.
Disconnect the main and auxiliary antenna from the wireless LAN card.
7.
8.
Then take out the wireless LAN card from the main unit.
Chapter 3
2.
Turn over the keyboard as the image shows. Then disconnect the keyboard cable from the main board.
3.
4.
5.
Remove the four screws securing the middle cover. Two from the bottom, and two from the rear side.
6.
7.
8.
Disconnect the power board FFC cable and remove the middle cover.
Chapter 3
57
9.
58
Chapter 3
Remove the screw fastening the ODD bracket with the optical disk drive module on the bottom.
2.
Remove the ODD bracket and push the optical disk drive module outwards.
3.
4.
Press and release the PC dummy card from the PC slot as shown.
5.
Then press the release the memory dummy card from the 5-in-1 card reader slot as shown.
6.
Remove the screw fastening the upper case and the lower case assembly from the rear side as shown.
7.
8.
Remove the seventeen screws fastening the upper case and the lower case assembly on the bottom.
9.
Remove the five screws fastening the upper case assembly and the lower case assembly on the front
side.
Chapter 3
59
10. Remove the five screws fastening the upper case assembly and the lower case assembly on the front
side.
11. Disconnect the touchpad board FFC, fingerprint FFC, and function board FFC from the main board.
12. Carefully detach the upper case assembly from the lower case assembly.
60
Chapter 3
21. Remove the screw holding the USB board to the lower case.
22. Then detach the USB cable and USB board from the lower case.
25. Use a flat screwdriver to release the CPU lock (Turn counter clock-wire).
26. Remove the CPU from the CPU socket carefully.
Chapter 3
61
2.
Remove the two screws fastening the function board to the upper case.
3.
4.
Detach the touchpad board FFC, fingerprinter FFC, and fingerprinter cable from the fingerprinter module.
5.
Remove the two screws fastening the fingerprinter bracket to the upper case.
62
6.
Remove the three screws fastening the fingerprinter module to the bracket.
7.
Chapter 3
2.
3.
4.
5.
Detach the two inverter cable connectors from the inverter board.
6.
7.
8.
9.
Remove the two screws fastening the left LCD bracket and detach it.
10. Remove the two screws fastening the right LCD bracket and detach it.
11. Disconnect the LCD cable from the LCD.
Chapter 3
63
12. Remove the two screws fastening the CCD bracket to the LCD panel.
13. Detach the CCD cable connector from the CCD board.
14. Remove the two screws fastening the CCD board to the CCD bracket.
64
Chapter 3
Remove the four screws holding the HDD (hard disk drive) case; two on each side.
2.
Carefully take out the hard disk drive from the HDD case.
2.
Then remove the optical bracket from the optical disk drive.
Chapter 3
65
66
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Chapter 4
67
Boot from the diagnostics diskette and start the diagnostics program.
2.
3.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
2.
3.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
2.
3.
2.
3.
68
Numeric keypad
External keyboard
Chapter 4
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board).
2.
3.
2.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
69
1.
2.
70
3.
If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4.
If the operational charge does not work, see Check the Battery Pack on page 71.
Chapter 4
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
4.
From Hardware:
1.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesnt work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
2.
3.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
71
72
Chapter 4
Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before Equipment Configuration
Error)
010
070
071
072
110
System disabled.
Incorrect password is specified.
FRU/Action in Sequence
Reconnect hard disk drive connector.
Load Default Settings in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
Keyboard error
BIOS ROM
System board
DIMM
System board
DIMM
System board
RTC battery
RTC battery
Chapter 4
73
FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See External Diskette Drive Check on page 68.
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System board
CPU ID:
System board
DIMM
System board
DIMM
System board
DIMM
System board
DIMM
BIOS ROM
System board
Fixed Disk n
None
BIOS ROM
System board
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
74
Chapter 4
FRU/Action in Sequence
Power source (battery pack and power adapter). See Power
System Check on page 69..
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
Chapter 4
75
Beeps
02h
03h
04h
06h
08h
09h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
12h
13h
14h
16h
17h
18h
1Ah
1Ch
20h
1-3-1-1
22h
1-3-1-3
24h
26h
28h
Autosize DRAM
29h
2Ah
2Ch
1-3-4-1
2Eh
1-3-4-3
2Fh
30h
76
32h
33h
36h
38h
3Ah
Autosize cache
3Ch
3Dh
42h
45h
Chapter 4
Code
46h
Beeps
2-1-2-3
48h
49h
4Ah
4Bh
4Ch
4Eh
50h
51h
52h
Test keyboard
54h
58h
59h
5Ah
5Bh
5Ch
60h
62h
64h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Eh
70h
72h
76h
7Ch
7Eh
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
Chapter 4
77
Code
Beeps
8Ch
8Fh
90h
91h
92h
Jump to UserPatch2
93h
95h
96h
97h
98h
99h
9Ah
9Ch
9Dh
9Eh
9Fh
A0h
A2h
A4h
A8h
Erase F2 prompt
AAh
ACh
Enter SETUP
AEh
B0h
B2h
B4h
78
B5h
B6h
B9h
Prepare Boot
BAh
BBh
BCh
BDh
BEh
BFh
C0h
C1h
C2h
C3h
C4h
C5h
C6h
C7h
C8h
C9h
Chapter 4
Code
Beeps
D2h
Code
Beeps
E0h
E1h
E2h
E3h
E4h
E5h
E6h
E7h
Go to BIOS
E8h
E9h
EAh
EBh
ECh
EDh
EEh
EFh
F0h
F1h
F2h
Initialize video
F3h
F4h
F5h
F6h
F7h
Chapter 4
79
Action in Sequence
LCD inverter ID
Abnormal screen
LCD cable
LCD inverter
LCD
System board
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See Power
System Check on page 69.
Battery pack
Power adapter
Hard drive & battery connection board
System board
80
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery cant be charged
Action in Sequence
See Check the Battery Pack on page 71.
Battery pack
System board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
System board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
Audio driver
Speaker
Speaker
System board
System board
Action in Sequence
See Save to Disk (S4) on page 45.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
Chapter 4
81
Action in Sequence
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System board
Print problems.
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see Undetermined
Problems on page 84.
82
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
83
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See Power
System Check on page 69.):
84
1.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Non-Acer devices
Battery pack
DIMM
PC Cards
4.
5.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
System board
LCD assembly
Chapter 4
Chapter 5
4 5
6
7
3
10
8 9
11
13
12
15
14
17
16
18
19
20 21 22 23 24
1
CN21
CN20
U26
CN18
CN17
S-Video Connector
17
U33
PJ1
DC-in Jack
18
U34
CN19
Ethernet Controller
19
CN28
CN24
DIMM Socket
20
CN23
Line-in Jack
CN25
DIMM Socket
21
CN29
Microphone-in Jack
10
CN23
Fan Connector
22
CN31
Headphones/Speaker/Line-out
Jack
11
U29
North Bridge
23
CN30
12
U30
CPU Socket
24
J40
Infrad Sensor
Chapter 5
13
CN26
14
U32
South Bridge
15
CN27
16
U39
Audio Codec
85
Bottom View
6
7
4
5
8
10
9
11
14
15
12
13
16
18
19
17
86
CN1
11
CN11
CN2
LCD Connector
12
U17
USB Connector
CN3
13
CN4
14
CN8
Touchpad Connector
(Fingerprinter to Main Board)
CN5
Bluetooth Connector
15
CN9
Fingerprinter Connector
U3
16
PU6
PU3
17
CN16
Speaker Connector
U10
18
CN14
U14
19
CN15
10
CN7
Keyboard Connector
Chapter 5
Chapter 6
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
87
No.
ADAPTER
ADAPTER 65W 3 PIN Delta SADP65KB DBRF LF
AP.06501.010
AP.06506.004
BT.00603.039
BT.00604.017
BT.00603.040
BT.00604.005
BT.00904.003
54.TG607.001
54.TAXV7.001
KI.GLN01.001
KI.GLN01.002
KI.GLN01.003
KI.GLN01.004
KI.GLN01.005
KI.KDN01.001
KI.KDN01.002
KI.KDN01.003
KI.KDN01.004
54.AZL07.001
BOARD
88
Chapter 6
Category
No.
FUNCTION BOARD
55.TG607.001
55.TG607.002
USB BOARD
55.TG607.003
LED BOARD
55.TG607.004
27.A03V7.006
27.A50V7.002
27.A99V7.002
27.A99V7.004
27.A99V7.005
27.T48V7.001
27.TAXV7.001
27.TATV7.001
27.TATV7.003
BLUETOOTH CABLE
50.TG607.001
50.TG607.002
50.TG607.003
50.TG607.004
CABLE
Chapter 6
89
Category
No.
CASE/COVER/BRACKET ASSEMBLY
MIDDLE COVER
42.TG607.001
60.TG607.001
60.TG607.002
42.TG607.002
42.TG607.003
RAM DOOR
42.TG607.004
TP BRACKET
33.TG607.003
42.TDY07.003
DUMMY 4 IN 1 CARD
42.TG607.005
KC.71001.DTP
KC.73001.DTP
KC.75001.DTP
CPU/PROCESSOR
90
Chapter 6
Category
No.
KC.77001.DTP
6M.TG607.007
KO.0240E.005
KO.0240D.005
ODD BRACKET
33.TG607.004
42.TG607.006
6M.TG607.008
KU.0080D.027
KU.00807.055
KU.0080D.027
OPTICAL BRACKET
33.TG607.004
42.TG607.007
KH.08007.021
KH.08004.010
COMBO MODULE
DVD-RW DRIVE
KH.08008.033
80GB WD 2.5" 5400rpm 80GB
WD800BEVS-22RST0 ML80 SATA LF F/
W:04.01G04
Chapter 6
91
Category
No.
KH.12007.010
KH.12004.006
KH.12008.018
KH.12001.031
KH.16007.011
KH.16004.001
KH.16008.019
KH.16001.026
KH.20004.001
42.TG607.008
KB.INT00.171
KB.INT00.172
KB.INT00.173
KEYBOARD
KB.INT00.174
Keyboard 12KB-FV1 Victoria Internal
Standard 85KS Black Turkish (change +*/ location)
92
KB.INT00.175
KB.INT00.176
KB.INT00.177
Chapter 6
Category
No.
KB.INT00.178
KB.INT00.180
KB.INT00.181
KB.INT00.182
KB.INT00.183
KB.INT00.185
KB.INT00.187
Keyboard 12KB-FV1 Victoria Internal
Standard 84KS Black Korean (change +*/ location)
Keyboard 12KB-FV1 Victoria Internal
Standard 88KS Black Japanese (change
+-*/ location)
KB.INT00.188
KB.INT00.189
KB.INT00.192
KB.INT00.193
KB.INT00.194
KB.INT00.195
Keyboard 12KB-FV1 Victoria Internal
Standard 85KS Black French (change +*/ location)
Keyboard 12KB-FV1 Victoria Internal
Standard 85KS Black Dutch (change +-*/
location)
KB.INT00.197
KB.INT00.198
Keyboard 12KB-FV1 Victoria Internal
Standard 85KS Black Danish (change +*/ location)
Chapter 6
KB.INT00.199
KB.INT00.201
KB.INT00.202
KB.INT00.202
93
Category
No.
KB.INT00.204
KB.INT00.205
KB.INT00.190
KB.INT00.179
KB.INT00.184
KB.INT00.186
KB.INT00.191
KB.INT00.196
Keyboard 12KB-FV1 Victoria Internal
Standard 85KS Black Finnish (change +*/ location)
LCD
94
6M.TG607.001
LK.12105.009
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.003
60.TG607.004
60.TG607.005
Chapter 6
Category
Chapter 6
No.
33.TG607.001
33.TG607.002
6M.TG607.002
LK.12105.009
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.006
60.TG607.007
60.TG607.005
33.TG607.001
33.TG607.002
6M.TG607.003
LK.12105.009
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.008
60.TG607.009
60.TG607.005
33.TG607.001
33.TG607.002
LK.12105.009
19.TG607.001
LCD CABLE
50.TG607.006
33.TG607.001
33.TG607.002
LK.12105.009
19.TG607.001
LCD CABLE
50.TG607.006
33.TG607.001
95
Category
96
No.
33.TG607.002
6M.TG607.004
LK.12105.008
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.003
60.TG607.004
60.TG607.005
33.TG607.001
33.TG607.002
6M.TG607.005
LK.12105.008
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.006
60.TG607.007
60.TG607.005
33.TG607.001
33.TG607.002
6M.TG607.006
LK.12105.008
19.TG607.001
LCD CABLE
50.TG607.006
60.TG607.008
60.TG607.009
60.TG607.005
33.TG607.001
33.TG607.002
LK.12105.008
19.TG607.001
LCD CABLE
50.TG607.006
33.TG607.001
33.TG607.002
Chapter 6
Category
No.
LK.12105.008
19.TG607.001
LCD CABLE
50.TG607.006
33.TG607.001
33.TG607.002
MB.TG606.001
KN.5120G.019
KN.51203.032
KN.5120B.023
KN.1GB0G.006
KN.1GB03.014
KN.1GB0B.011
THERMAL MODULE
60.TG607.010
40.TG607.001
57.TG607.001
57.TG607.002
SPEAKER ASSY
23.TG607.001
SCREW M2.0*3.0-I-NI-NYLOK
86.A08V7.005
SCREW M3*0.5+3.5I
86.TDY07.003
MAINBOARD
MEMORY
HEATSINK
MISCELLANEOUS
CCD
SPEAKER
SCERW
Chapter 6
97
Category
98
No.
86.FR6V7.003
SCREW M2.0*6-I-BNI(NYLOK)
86.TG607.001
86.TG607.002
SCREW M2.0*1.5-I(NI)(ANTI-LOOSE)
86.TG607.003
SCREW M2*5-I(BZN)(NYLOK)
86.TG607.004
Chapter 6