Sei sulla pagina 1di 7

SEMICONDUCTOR

KIA34063A/AF

TECHNICAL DATA

BIPOLAR LINEAR INTEGRATED CIRCUIT

DC/DC Converter Controller


The KIA34063A/AF series is a monolithic control circuit
containing the primary functions required for DC-to-DC
converters. These devices consist of an internal temperature
compensated reference, comparator, controlled duty cycle
oscillator with an active current limit circuit. driver and high
current output switch. This series was specifically designed to
be incorporated in Step-Down and Step-Up and Voltage-Inverting
applications with a minimum number of external components.

DIM MILLIMETERS
_ 0.2
A
9.6 +
_ 0.2
B
6.45 +
_ 0.1
D
1.52 +
_ 0.1
d
0.46 +
G
0.50 MIN
_ 0.3
H
3.8 +
_ 0.3
L
3.3 +
P
2.54
T
0.25+0.1/-0.05
W
7.62
0 - 15
Q

A
5

FEATURES
Operation from 3.0V to 40V input.

Low Standby Current.


Current Limiting.
Output Switch Current to 1.5A.
Output Voltage Adjustable.

DIP-8

Frequency Operation to 100kHz.

SWITCH
EMITTER

DRIVER
COLLECTOR

I PK SENSE

SWITCH
COLLECTOR

Precision 2% Reference.

GND

COMPARATOR
INVERTING
INPUT

B1

VCC

B2

TIMING
CAPACITOR

DIM
A
B1
B2
D
G
H
L
P
T

MILLIMETERS
_ 0.2
4.85 +
_ 0.2
3.94 +
_ 0.3
6.02 +
_ 0.1
0.4 +
0.15+0.1/-0.05
_ 0.2
1.63 +
_ 0.2
0.65 +
1.27
0.20+0.1/-0.05

FLP-8

2001. 4. 16

Revision No : 2

1/7

KIA34063A/AF
MAXIMUM RATINGS (Ta=25

CHARACTERISTIC

SYMBOL

RATING

UNIT

Power Supply Voltage

VCC

40

Comparator Input Voltage Range

VIR

-30 40

Switch Collector Voltage

VC(SWITCH)

40

Switch Emitter Voltage (VPIN1=40V)

VE(SWITCH)

40

Switch Collector to Emitter Voltage

VCE(SWITCH)

40

Driver Collector Voltage

VC(DRIVER)

40

Driver Collector Current (Note 1)

IC(DRIVER)

100

mA

ISW

1.5

Switch Current
Power Dissipation

KIA34063A
KIA34063AF

500

PD

mW

320

Operating Temperature

Topr

-30 75

Storage Temperature

Tstg

-65 150

Note 1) Maximum package power dissipation limits must be observed.

BLOCK DIAGRAM

DRIVER
COLLECTOR

SWITCH
COLLECTOR

Q2

S Q
R

Q1
100

I PK
SENSE

I PK
OSCILLATOR

CT

VCC

COMPARATOR
+
COMPARATOR
INVERTING
INPUT

2001. 4. 16

Revision No : 2

SWITCH
EMITTER

TIMING
CAPACITOR

1.25V
REFERENCE
REGULATOR

4
GND

2/7

KIA34063A/AF
ELECTRICAL CHARACTERISTICS (VCC=5.0V, Ta=25

, unless otherwise specified)

OSCILLATOR SECTION
CHARACTERISTIC

SYMBOL

TEST CONDITION

MIN.

TYP.

MAX.

UNIT

Frequency

fOSC

VPIN5=0V, CT=1.0nF

24

33

42

kHz

Charge Current

ICHG

VCC=5.0 40V

24

35

42

IDISCHG

VCC=5.0 40V

140

220

260

Discharge Current
Discharge to Charge Current Ratio

IDISCHG/ICHG

Pin 7 VCC

5.2

6.5

7.5

Current Limit Sense Voltage

VIPK(SENSE)

IDISCHG=ICHG

250

300

350

mV

MIN.

TYP.

MAX.

UNIT

1.0

1.3

0.45

0.7

50

75

0.01

100

MIN.

TYP.

MAX.

UNIT

1.225

1.25

1.275

1.21

1.29

VCC=3.0 40V

1.4

5.0

mV

VIN=0

-20

-400

nA

MIN.

TYP.

MAX.

UNIT

4.0

mA

OUTPUT SWITCH SECTION (Note 2)


CHARACTERISTIC

SYMBOL

Saturation Voltage,

TEST CONDITION

VCE(SAT1)

Darlington Connection

ISW=1.0A, Pins 1, 8 Connection


ISW=1.0A, Forced =

VCE(SAT2)

Saturation Voltage (Note 3)

RPIN8=82

hFE

DC Current Gain

to VCC

ISW=1.0A, VCE=5.0A,

IC(OFF)

Collector Off-State Current

20

VCE=40V

COMPARATOR SECTION
CHARACTERISTIC

SYMBOL

TEST CONDITION

Threshold Voltage

VTH1

Ta=25

Threshold Voltage

VTH2

Ta=TLOW

Threshold Voltage Line Regulation

Reg line
IIB

Input Bias Current

THIGH

TOTAL DEVICE
CHARACTERISTIC

SYMBOL

TEST CONDITION
VCC=5.0 40V, CT=1.0nF,
Pin 7=VCC, Pin 2=GND,
VPIN5 VTH, remaining pins open

ICC

Supply Current

Note) 2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient temperature as possible.
3. If the output switch is driven into hard saturation (non-Darlington configuration) at low switch currents ( 300mA) and high driver
currents ( 30mA), it may take up to 2.0 S for it to come out of saturation. This condition will shorten the off time at frequencies
30kHz, and is magnified at high temperatures. This condition does not occur with a Darlington configuration, since the output
switch cannot saturate. If a non-Darlington configuration is used, the following output drive condition is recommended ;
Forced of output switch :
* The 100

2001. 4. 16

IC output
IC driver-7.0mA *

10

resistor in the emitter of the driver device requires about 7.0mA before the output switch conducts.

Revision No : 2

3/7

KIA34063A/AF
APPLICATION CIRCUIT
(1) Step-up Converter
170H
L
8

180
Q2

S Q
R

Q1
100

I PK

Rsc
0.22
Vin
12V

OSC
6

1N5819
3

VCC

CT

+
100

CT

+
-

COMP.

1.25V
REF
REG

1500
pF
4

47K

VOUT

+
330

+
CO

2.2K

R1

1.0H

Vout
28V/175mA

R2

100

OPTIONAL FILTER

TEST

2001. 4. 16

CONDITIONS

RESULTS

Line Regulation

VIN=8.0V to 16V, IO=175mA

30mV=

0.05%

Load Regulation

VIN=12V, IO=75mA to 175mA

10mV=

0.017%

Output Ripple

VIN=12V, IO=175mA

400 mVpp

Efficiency

VIN=12V, IO=175mA

87.7%

Output Ripple With Optional Filter

VIN=12V, IO=175mA

40 mVpp

Revision No : 2

4/7

KIA34063A/AF

(2) Step-Down Converter

Q2

S Q
R

Q1
100

I PK

R sc
0.33

OSC
6

Vin
25V

1N5819
3

VCC

CT

220H

+
100

CT

+
-

COMP.

1.25V
REF
REG

470
pF

3.6K

VOUT

+
100

CO

470

1.2K

R1

1.0H

Vout
5.0V/500mA

R2

OPTIONAL FILTER

TEST

CONDITIONS

RESULTS

Line Regulation

VIN=15V to 25V, IO=500mA

12mV=

Load Regulation

VIN=25V, IO=50mA to 500mA

3.0mV= 0.03%

Output Ripple

VIN=25V, IO=500mA

120 mVpp

Short Circuit Current

VIN=25V, RL=0.1

1.1A

Efficiency

VIN=25V, IO=500mA

83.7%

Output Ripple With Optional Filter

VIN=25V, IO=500mA

40 mVpp

2001. 4. 16

Revision No : 2

0.12%

5/7

KIA34063A/AF

(2) Voltage Inverting Converter

1
Q2

S Q
R

Q1
100

2
L
I PK

Rsc
0.24

OSC
6

CT
3

VCC

(
5

1.25V
REF
REG

+
COMP.
-

1N5819

1500
pF

VOUT

1000f

8.2K

953
R2

1.0H

Vout
-12V/100mA

R1
CO

Vin
4.5V TO 6.0V +
100

88H

100

OPTIONAL FILTER

TEST

2001. 4. 16

CONDITIONS

RESULTS

Line Regulation

VIN=4.5V to 6.0V, IO=100mA

3.0mV= 0.012%

Load Regulation

VIN=5.0V, IO=10mA to 100mA

0.022V= 0.09%

Output Ripple

VIN=5.0V, IO=100mA

500 mVpp

Short Circuit Current

VIN=5.0V, RL=0.1

910mA

Efficiency

VIN=5.0V, IO=100mA

62.2%

Output Ripple With Optional Filter

VIN=5.0V, IO=100mA

70 mVpp

Revision No : 2

6/7

KIA34063A/AF

t on , t off - C T
VCC =5.0V
Pin7=VCC
Pin5=GND
Ta=25 C

t on

10

t off

1
10

10

10

10

200mV/DIV

10

OSCILLATOR VOLTAGE VOSC (V)

OUTPUT SWITCH ON-OFF TIME


t on-off (s)

10

TIMING CAPACITOR WAVEFORM

VCC =5.0V
Pin7=VCC
Pin2=GND

Pins1,5,8=OPEN
CT =1.0nF
Ta=25 C

10s/DIV

OSCILLATOR TIMING CAPACITOR C T (pF)

VCE(sat) - I C
SATURATION VOLTAGE VCE(sat) (V)

SATURATION VOLTAGE VCE(sat) (V)

VCE(sat) - I E
1.8
1.7
1.6
1.5
1.4
VCC =5.0V
Pins1,7,8=VCC
Pins3,5=GND
Ta=25 C
(SEE NOTE 3)

1.3
1.2
1.1
1.0
0

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.1
1.0
0.9
0.8
0.7

DARLINGTON CONNECTION
VCC =5.0V
Pin7=VCC
Pins2,3,5=GND
Ta=25 C
(SEE NOTE 3)

0.6
0.5
0.4
0.3
0.2
0.1
0

1.6

0.2

EMITTER CURRENT I E (A)

0.4

SUPPLY CURRENT I CC (mA)

CURRENT LIMIT SENSE VOLTAGE


VIPK(SENSE) (V)

1.0

1.2

1.4

1.6

3.6

VCC =5.0V
I chg =I dischg

360
340
320
300
280
260
240
220

3.2
2.8
2.4
2.0
1.6
1.2
C T =1.0nF

0.8

PIN7=VCC

0.4

Pin2=GND

0
-25

25

50

75

100

AMBIENT TEMPERATURE Ta ( C)

2001. 4. 16

0.8

I CC - VCC

400

200
-55

0.6

COLLECTOR CURRENT I C (A)

VIPK(SENSE) - Ta
380

FORCED =20

Revision No : 2

125

10

15

20

25

30

35

40

SUPPLY VOLTAGE VCC (V)

7/7

Potrebbero piacerti anche