Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Note: Encircle the letter of only one answer which you think is most appropriate.
1.
2.
260 deg C
100 deg C
90 deg C
21 deg C
3.
As per API Standard 650, the overlap at lap-welded joints shall be at least
five times the nominal thickness of the thinner plate, but need not exceed,
a.
b.
c.
d.
4.
2 for single-welded lap joints and 4 for double welded lap joints
1 for single-welded lap joints and 2 for double welded lap joints
1.5 for single-welded lap joints and 2 for double welded lap joints
1.5 for single-welded lap joints and 1 for double welded lap joints
Calculate by the 1-Foot method the design shell thickness Td in inches, of the
following description of tank built to API Standard 650:
H = Design liquid level = 50 feet
D = Nominal Tank Diameter = 180 feet
G = Design Specific Gravity = 0.86
CA = Corrosion Allowance = 0. 0625
Sd= Allowable stress in design condition, in psi
Shell Material = ASTM A36M
Td = design shell thickness, inch(es)
St= Allowable stress for hydrostatic test condition, in psi
Tt = hydrostatic test shell thickness, inch(es).
Where, Td = 2.6 D (H 1) G + CA
Sd
a.0.912
b.0.850
c.1
d.0.922
5.
a.
b.
c.
d.
6.
7.
Where, Tt = 2.6 D (H 1)
St
0.935
0.985
1
0.922
5mm
2.4mm
1.6mm
3mm
Vertical joints of a 28 mm thick shell of an AST built to API Std. 650 shall be
radiographed to the extent as given below :
a.Full
b.Partial
c.Spot
d. Nil
8.
In an AST built to API Standard 650, the bottom annular plates have radial
weld joints, and are single butt welded with permanent back-up bar, in which
case, the extent of radiographing radial joints shall be,
a.
b.
c.
d.
9.
As per API Std. 650, personnel who perform and evaluate radiographic
examinations (RT) shall have a minimum qualification as follows :
a.
b.
c.
d.
10.
Shall
Shall
Shall
Shall
The minimum required shell thickness of a Tank of 60 Meter diameter (200 ft.
diameter), built to API Standard 650, shall be:
a.
b.
c.
d.
11.
12.
Not required
Required
Depends on opinion of design engineer
Depends on opinion of tank inspector
11, 12 Joules
24, 12 Joules
22, 10 Joules
10, 27 Joules
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
C
Ref.: API 650, 1.1.1
C
Ref.: API 650, 3.1.3.3
B
Ref.: API 650, 3.1.3.5
A
Ref.: API 650, 3.6.3.2 (td)
D
Ref.: API 650, 3.6.3.2 (tt)
A
Ref.: API 650, 5.2.1.5
A
Ref.: API 650, Fig. 6-1, Note 6
A
Ref.: API 650, 6.1.2.9
B
Ref.: API 650, 6.1.3.2
D
Ref.: API 650, 3.6.1.1
B
Ref.: API 650, Table 2-3B & Fig. 2-1
B
Ref.: API 650, Table 2-4
-----------------------------------------------