Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Precautions 1
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
Warning
1. Check the specifications.
Read the specifications carefully and use this product
appropriately. The product may be damaged or malfunction if it
is used outside the range of specifications of current current,
voltage, temperature or impact.
In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer
( 200 ms) makes it possible to extend the load operating time.
6-16-4
Auto Switches
Precautions 2
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
Warning
1. Do not drop or bump.
Do not drop, bump, or apply excessive impacts (300 m/s2 or
more for reed switches and 1000 m/s2 or more for solid state
switches) while handling. Although the body of the switch may
not be damaged, the inside of the switch could be damaged
and cause a malfunction.
Wiring
Warning
1. Avoid repeatedly bending or stretching lead
wires.
Broken lead wires will result from repeatedly applying bending
stress or stretching force to the lead wires.
CJ1
CJP
CJ2
CM2
CG1
MB
MB1
CA2
CS1
C76
C85
C95
CP95
NCM
NCA
D-X
20Data
2-wire
Output (+)
Output ()
3-wire
Old
Red
Black
New
Brown
Blue
Solid State
with Diagnostic Output
New
Old
Power supply (+) Red
Brown
Power supply GND Black
Blue
Output
White Black
Diagnostic output Yellow Orange
New
Old
Power supply (+)
Red Brown
Power supply GND Black Blue
Output
White Black
6-16-5
Auto Switches
Precautions 3
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
Operating Environment
Warning
1. Never use in the presence of explosive gases.
The construction of our auto switches does not make them
explosion-proof. Never use them in the presence of an
explosive gas, as this may cause a serious explosion.
6-16-6
Maintenance
Warning
1. Perform the following maintenance periodically
in order to prevent possible danger due to
unexpected auto switch malfunction.
1) Securely tighten switch mounting screws.
If screws become loose or the mounting position is
dislocated, retighten screws securely after readjusting the
mounting position.
2) Confirm that there is no damage to lead wires.
To prevent faulty insulation, replace switches or repair lead
wires if damage is discovered.
3) Confirm that the green light on the 2-color indicator type
switch lights up.
Confirm that the Green LED is ON when stopped at the set
position. If the Red LED is ON when stopped at the set
position, the mounting position is not appropriate. Readjust
the mounting position until the Green LED lights up.
Other
Warning
1. Please consult with SMC concerning water
resistance, elasticity of lead wires, and use at
welding sites.
Before Operation
Auto Switches Common Specifications
Precautions
Refer to Auto Switches Precautions on pages 6-16-4 to 6-16-6 before handling.
Reed switch
None
1.2 ms
1 ms or less (3)
300 m/s2
1000 m/s2
Leakage current
Operating time
Impact resistance
Insulation resistance
Withstand voltage
CJ1
Ambient temperature
Enclosure
(2)
1
<Applicable switch types>
D-A7/A8, D-A7H/A80H, D-A73C/A80C, D-C7/C8, D-C73C/C080C, DE7A/E80A, D-Z7/Z8, D-9/9A, D-A9/A9V, and D-A79W type
The above auto switches do not have internal contact protection circuits.
1. Operating load is an inductive load.
2. The length of wiring to the load is 5 m or more.
3. The load voltage is 100 or 200 VAC.
A contact protection box should be used in any of the above
conditions, Unless using a contact protection box, the contact life may
be shortened. (Due to permanent energizing conditions.)
D-A72(H) must be used with the contact protection box regardless
of load styles and lead wire length.
2
Please contact SMC when using built-in contact protection circuit style (DA34[A][C], D-A44[A][C], D-A54/A64, D-B54/B64, D-A59W, D-B59W) in the
following conditions: 1. The wiring length to load is more than 30 m; 2.
When using PLC with large flow current.
D-A73 L
D-F8PL- 61
CD-P12
24 VDC
Part no.
Load voltage
Max. load current
25 mA
Auto switch
Choke
coil
Zener diode
Choke
coil
Switch
operating
position
(OFF)
MB
MB1
CA2
CS1
C76
C85
C95
CP95
NCM
NCA
Data
OUT Brown
OUT () Blue
Switch
operating
position
(ON)
CG1
20-
OUT Blue
CD-P12
CM2
-X
50 mA
CJ2
D-
CD-P11
12.5 mA
CJP
6-16-7
Before Operation
Auto Switches Connection and Example
Basic Wiring
Solid state 3-wire, NPN
Brown
Brown
Brown
Load
Load
Main
curcuit
of switch
Main
curcuit
of switch
Black
Black
Load
Blue
Load
Indicator
protection
circuit,
etc.
Main
curcuit
of switch
Blue
Blue
Blue
Brown
Brown
Brown
Load
Main
curcuit
of switch
Indicator
protection
circuit,
etc.
Main
curcuit
of switch
Black
Load
Load
Blue
Blue
Blue
Switch
Input
Brown
Switch
Blue
Input
Brown
Blue
COM
COM
PLC internal circuit
2-wire
2-wire
Brown
Input
Switch
Blue
Input
Brown
COM
Switch
Blue
COM
PLC internal circuit
Switch 2
Brown
Black
Relay
Blue
Brown
Black
Relay
Blue
Switch 2
Switch 2
Brown
Black
Load
Blue
Switch 1
Brown
Black
Blue
Switch 2
Blue
Brown
Blue
Load
Load
Brown
Black
Blue
Switch 2
Blue
Brown
Load
(Reed switch)
Because there is no
current leakage, the load
voltage will not increase
when
turned
OFF.
However, depending on
the number of switches in
the ON state, the
indicator
lights
may
sometimes grow dim or
not light up, due to the
dispersion and reduction
of the current flowing to
the switches.
Blue
Load voltage at ON = Power supply voltage Residual voltage x 2 pcs. Load voltage at OFF = Leakage current x 2 pcs. x Load impedance
= 24 V 4 V x 2 pcs.
= 1 mA x 2 pcs. x 3 k
= 16 V
=6V
Example: Power supply is 24 VDC
Internal voltage drop in switch is 4 V.
6-16-8
Brown
Black
Blue
2-wire
Switch 1
Switch 1
6-15-36
Reed Switch
Band Mounting Style
D-C73/D-C76/D-C80
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-C76
Relay, PLC
IC circuit
24 VDC
100 VAC
4 to 8 VDC
5 to 40 mA
5 to 20 mA
20 mA
None
2.4 V or less
Indicator light
0.8 V or less
Load voltage
AC
24 V DC
or less
50 mA
Reed switch
LED
Brown
OUT (+)
Contact
Brown
protection
box
CD-P11
CD-P12
OUT ()
Blue
Resistor
Zener
diode
Blue
AC
100 V DC
40 mA
20 mA
None
Internal resistance
AC
48 V DC
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
(g)
Auto switch model
D-C76
Reed switch
LED
DC (+)
Brown
(+)
Resistor
Reverse
OUT
current
prevention Black
diode
0.5
3
5
D-C73
9
46
76
D-C76
10
50
Load
DC ()
Blue
DC
()
Dimensions
Contact
OUT ()
protection Brown
box
CD-P11
OUT ( )
CD-P12
Blue
6-16-10
Indicator light
D-C80 without indicator light
Reed switch
D-C80
D-C80
9
46
Reed Switch
Band Mounting Style
D-B53/D-B54/D-B64
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-B53
D-B54
PLC
Relay, PLC
CJ1
CJP
24 VDC
24 VDC
100 VAC
200 VAC
5 to 50 mA
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
CJ2
None
Built-in
2.4 V or less
Indicator light
24 V
AC
DC
or less
Max. 50 mA
100 VAC
200 VAC
Max. 25 mA
Max. 12.5 mA
MB1
Built-in
Internal resistance
CA2
25 or less
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
MB
Relay, PLC
Load voltage
OUT ()
Blue
CG1
D-B64
Applicable load
OUT (+)
Brown
Weight
(g)
D-B54
D-B53
D-B54
D-B64
0.5
22
22
22
78
78
78
126
126
Resistor
CP95
NCM
NCA
OUT (+)
Reed switch
LED
20-
Surge absorber
Data
Indicator light
DB64 without
indicator light
D-B64
Choke coil
OUT ( )
Blue
C85
-X
Choke coil
OUT ()
Blue
C76
D-
Dimensions
Zener diode
CS1
C95
Zener diode
CM2
Reed switch
Surge absorber
OUT ()
Brown
Most sensitive
position
6-16-11
Reed Switch
Band Mounting Style
D-C73C/D-C80C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Connector
Relay, PLC
Load voltage
24 VDC
5 to 40 mA
None
2.4 V or less
Indicator light
Precautions
OUT ( )
Blue
Blue
None
Internal resistance
Weight
D-C80C
Contact protection box
OUT ()
Brown
14
14
53
53
83
83
Dimensions
Lead wire with connector
OUT ( )
Blue
Indicator light
D-C80C without
indicator light
6-16-12
D-C80C
0.5
CD-P11
CD-P12
D-C73C
Reed switch
50 mA
(g)
Reed switch
Choke coil
Resistor
Zener diode
24 V AC
DC or less
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Lead wire with connector may be shipped with switch.
Note 4) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Brown
Relay, PLC
Load voltage
LED
D-C80C
Caution
Reed Switch
Band Mounting Style
D-A33/D-A34/D-A44
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
(2)
D-A34
PLC
Relay, PLC
24 VDC
24 VDC
100 VAC
200 VAC
5 to 50 mA
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
None
2.4 V or less
Precautions
CG1
D-A44
Applicable load
Load current range
24 VDC
100 VAC
200 VAC
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
MB1
Built-in
CA2
Indicator light
MB
Relay, PLC
Load voltage
CS1
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
LED
Resistor
OUT (+)
Terminal no. 1
(g)
Auto switch model
Lead wire
D-A34, D-A44
None
D-A33
D-A34
D-A44
116
116
114
D-A3
Tightening
gland
LED
Resistor
C85
CP95
NCM
NCA
Dimensions
Choke coil
C76
C95
Weight
Zener diode
Reed switch
CM2
OUT ()
Terminal no. 2
CJ2
Caution
Reed switch
CJP
Built-in
Indicator light
OUT ()
Terminal no. 2
CJ1
D-A33
Applicable load
OUT (+)
Terminal no. 1
D-
D-A44
Tightening
gland
-X
20-
Zener diode
Surge absorber
G 1/2
Applicable cable O.D. 6.8 to 9.6
Indicator light
G 1/2
Applicable cable O.D. 6.8 to 11.5
6-16-13
Data
Reed Switch
Band Mounting Style
D-A33A/D-A34A/D-A44A
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
D-A3
PLC
Load voltage
Load current range (2)
Internal voltage drop
Relay, PLC
24 VDC
24 VAC
100 VAC
200 VAC
5 to 50 mA
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
Caution
None
Built-in
2.4 V or less
Indicator light
Precautions
D-A44A
Relay, PLC
Applicable load
Load voltage
Load current range
24 VDC
100 VAC
200 VAC
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
Resistor
Built-in
2.4 V or less (to 20 mA)/3.5 V or less (to 50 mA)
Indicator light
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
LED
OUT ()
Terminal no. 2
D-A34A
OUT (+)
Terminal no. 1
Zener diode
Weight
D-A34A, D-A44A
(g)
Auto switch model
Choke coil
LED
Reed switch
OUT ()
Terminal no. 2
Resistor
Lead wire
None
D-A33A
D-A34A
D-A44A
112
112
110
OUT (+)
Terminal no. 1
Zener diode
Surge absorber
Dimensions
D-A3A
D-A44
G 1/2
(Applicable cable O.D.
6.8 to 9.6)
Tightening gland
6-16-14
Tightening gland
G 1/2
(Applicable cable O.D.
6.8 to 11.5)
Reed Switch
Band Mounting Style
D-A72/D-A73/D-A80
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Electrical entry: Perpendicular
D-A73
Relay, PLC
Relay, PLC
(3)
CJ1
200 VAC
24 VDC
100 VAC
5 to 10 mA
5 to 40 mA
5 to 20 mA
CJP
CJ2
None
2.4 V or less
Indicator light
CM2
CG1
24
LED
Brown
Choke
coil
Reed switch
OUT
Brown
Surge
absorber
OUT
Blue
Blue
48
AC
V DC
40 mA
100 V
AC
DC
MB1
20 mA
None
CA2
Internal resistance
Zener diode
or less
Resistor
AC
V DC
50 mA
MB
Applicable load
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Brown
Contact
protection
box
CD-P11
CD-P12
Reed switch
Resistor
Zener diode
Blue
OUT (+)
Brown
D-A73
D-A80
10
10
10
47
47
47
77
OUT ()
Blue
Dimensions
15 (14)
6 (6.2) 3
NCM
NCA
D-
Data
23 (22)
OUT ()
Brown
OUT ( )
Blue
CP95
20-
Contact
protection
box
CD-P11
CD-P12
C85
-X
Indicator light
D-A80 without
indicator light
D-A80
Reed switch
D-A72
0.5
C76
C95
Weight
(g)
D-A73
CS1
9 (8.5)
6-16-15
Reed Switch
Rail Mounting Style
D-A7 H/D-A80H
Grommet
Electrical entry: In-line
D-A72H
D-A73H
D-A76H
Relay, PLC
Relay, PLC
IC circuit
200 VAC
24 VDC
100 VAC
5 to 10 mA
5 to 40 mA
5 to 20 mA
2.4 V or less
LED
Brown
OUT
Brown
Choke
coil
Resistor
Reed switch
Zener diode
Surge
absorber
OUT
Blue
Blue
D-A73H
LED
Brown
Contact
protection
box
CD-P11
CD-P12
Resistor
Reed switch
20 mA
0.8 V or less
None
Indicator light
D-A72H
4 to 8 VDC
Zener diode
Blue
OUT (+)
Brown
D-A80H
Applicable load
AC
Load voltage
Maximum load current
24 V DC or less
48 V DC
AC
100 V DC
AC
50 mA
40 mA
20 mA
None
Internal resistance
Lead wire Oil resistant vinyl heavy-duty cord, 0.2 mm2, 2 cores (Brown, Blue), 3 cores (Brown,
Black, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
OUT ()
Blue
Weight
(g)
D-A72H
D-A73H
D-A76H
D-A80H
0.5
10
10
11
10
47
47
52
47
D-A76H
DC (+)
Brown
LED
Reed switch
Resistor
Reverse
current
prevention
diode
OUT
Black
Load
DC ()
Blue
77
(+)
DC power
supply
()
Dimensions
D-A7H, D-A80H
Contact
protection
box
CD-P11
CD-P12
OUT ()
Brown
OUT ( )
Blue
6-16-16
Indicator light
D-A80H without
indicator light
Reed switch
D-A80H
Reed Switch
Rail Mounting Style
D-A73C/D-A80C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Connector
Relay, PLC
Load voltage
5 to 40 mA
(4)
2.4 V or less
Indicator light
Precautions
OUT (+)
Brown
Resistor
Zener
diode
Zener diode
Load voltage
AC
24 V DC
50 mA
CA2
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Lead wire with connector may be shipped with switch.
Note 4) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
D-A80C
OUT ()
Brown
CS1
C76
C85
C95
CP95
(g)
D-A73C
D-A80C
0.5
12
12
54
54
84
84
NCM
NCA
D-
Dimensions
-X
20-
Contact
protection
box
CD-P11
CD-P12
MB1
None
OUT ()
Blue
Blue
MB
Applicable load
Internal resistance
Brown
CG1
D-A80C
Reed switch
CM2
Caution
Reed switch
CJ2
None
LED
CJP
24 VDC
CJ1
D-A73C
OUT ( )
Blue
Lead wire
with connector
Data
Indicator light
D-A80C without
indicator light
6-16-17
Reed Switch
Tie-rod Mounting Style
D-A5 /D-A6
Grommet
D-A53
D-A54
D-A56
PLC
Relay, PLC
IC circuit
Applicable load
Load voltage
24 VDC
24 VDC
100 VAC
200 VAC
4 to 8 VDC
5 to 50 mA
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
20 mA
None
Built-in
None
2.4 V or less
0.8 V or less
Indicator light
D-A67
Relay, PLC
PLC/IC circuit
AC
24 V DC
or less
100 VAC
200 VAC
Max. 24 VDC
50 mA
25 mA
12.5 mA
30 mA
LED
OUT ()
Blue
OUT (+)
Brown
Resistor
Zener diode
D-A54
Built-in
None
1 or less
25 or less
(Including lead wire
Internal resistance
length of 3 m)
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 2 cores (Brown, Blue), or 0.2 mm 3
cores (Brown, Black, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
Zener diode
Choke coil
(g)
Resistor
OUT ()
Blue
OUT (+)
Reed
switch
LED
Surge absorber
D-A53
D-A54
D-A56
D-A64
0.5
24
24
24
48
96
48
48
D-A56
DC (+)
Brown
LED
Reed switch
Resistor
OUT
Reverse
current
Black
prevention
diode
DC ()
Blue
(+)
Dimensions
Load
DC power supply
()
D-A64
Choke coil
OUT ( )
Blue
Reed switch
OUT ()
Brown
Indicator light
D-A64/A67 without
indicator light
Surge absorber
D-A67
Most sensitive position
Reed switch
OUT ( )
Blue
6-16-18
OUT ()
Brown
D-A67
Reed Switch
Tie-rod Mounting Style
D-A33C/D-A34C/D-A44C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Terminal conduit:D-A3C
DIN terminal: D-A44C
D-A33C
D-A34C
PLC
Relay, PLC
24 VAC
100 VAC
200 VAC
5 to 50 mA
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
None
Built-in
2.4 V or less
Indicator light
CM2
LED
Terminal no. 2
Resistor
OUT (+)
Terminal no. 1
CG1
D-A44C
Precautions
Applicable load
Relay, PLC
Load voltage
Load current range (2)
MB
24 VDC
100 VAC
200 VAC
5 to 50 mA
5 to 25 mA
5 to 12.5 mA
MB1
Built-in
Indicator light
CA2
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the indicator
light will not be possible where the output signal is less than 2.5 mA. However, there is no
problem in terms of contact output, when an output signal exceeds 1 mA or more.
Weight
(g)
Zener diode
Reed switch
OUT ()
Choke coil
LED
Resistor
Terminal no. 2
D-A33C
D-A34C
D-A44C
40
162
162
160
50
166
166
164
63
184
184
182
80
210
210
208
100
232
232
230
D-A34C, D-A44C
OUT (+)
Terminal no. 1
Zener diode
D-A3C
Hexagon socket
head cap bolt
G 1/2
Applicable cable O.D.
6.8 to 9.6
D-A44C
Hexagon socket
head cap bolt
NCA
C
HW
H'
44
52
64
78
92
69
77
91
107
121
58 (67.5)
59 (68.5)
61.5 (71)
65 (74.5)
68 (77.5)
T'
6.5
6.5
7.5
9.5
9.5
D-X
M5 x 0.8 x 16
M5 x 0.8 x 20
M5 x 0.8 x 25
2-M5 x 0.8 x 12
Hexagon socket head cap bolt
Tightening gland
G 1/2
Applicable cable O.D.
6.8 to 11.5
Indicator light
Most sensitive position
C85
NCM
(mm)
2-M5 x 0.8 x 12
Hexagon socket head cap bolt
Tightening gland
C76
C95
Dimensions
Applicable bore
Auto switch model
size (mm)
40
D-A3C-4, D-A44C-4
50
D-A3C-5, D-A44C-5
63
D-A3C-6, D-A44C-6
80
D-A3C-8, D-A44C-8
100
D-A3C-10, D-A44C-10
( ): Denotes the values of D-A44C
CS1
CP95
Surge absorber
Dimensions
CJP
CJ2
Caution
OUT ()
CJ1
24 VDC
6-16-19
20Data
Reed Switch
Direct Mounting Style
D-A90(V)/D-A93(V)/D-A96(V)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Electrical entry: In-line
D-A90, D-A90V
Applicable load
Load voltage
Maximum load current
24 V AC
DC or less
48 V AC
DC or less
100 V AC
DC or less
50 mA
40 mA
20 mA
None
Internal resistance
Caution
D-A93, D-A93V
Applicable load
Precautions
1. Fix the switch with appropriate screw
installed on the switch body. If using other
screws, switch may be damaged.
Load voltage
IC circuit
24 VDC
100 VAC
4 to 8 VDC
5 to 40 mA
5 to 20 mA
20 mA
(3)
Contact
protection
box
CD-P11
CD-P12
OUT()
Brown
Reed switch
D-A90V
OUT ( )
Blue
D-A96, D-A96V
Relay, PLC
None
0.8 V or less
Indicator light
Red LED lights when ON.
Lead wire
D-A90(V)/D-A93(V)Oil resistant vinyl heavy-duty cord, 2.7, 0.18 mm2 x 2 cores (Brown, Blue), 0.5 m
D-A96(V)Oil resistant vinyl heavy-duty cord, 2.7, 0.15 mm2 x 3 cores (Brown, Black, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the indicator
light will not be possible where the output signal is less than 2.5 mA. However, there is no
problem in terms of contact output, when an output signal exceeds 1 mA or more.
Weight
(g)
D-A93V
LED
Brown (Red)
Contact
protection
box
CD-P11
CD-P12
Reed switch
Resistor
Zener diode
OUT (+)
Brown
OUT ()
Blue
Blue (Black)
D-A96
D-A96V
Model
D-A90
D-A90V
D-A93
D-A93V
30
41
41
30
30
30
Dimensions
D-A90, D-A93, D-A96
D-A96V
LED
DC (+)
Brown
(+)
Reed switch
Resistor
Reverse
OUT
current
Black
prevention
diode
DC ()
Blue
Load
DC
power supply
Indicator light
D-A90 without indicator light
M2.5 x 4l
Slotted set screw
()
Most sensitive
position
( ): dimensions for D-A93.
Indicator light
D-A90V without indicator light
6-16-20
Reed Switch
Direct Mounting Style
D-90/D-97
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Lead wire: Parallel cord
CJ1
CJP
24 VAC
24 VDC
12 VAC
12 VDC
5 VAC
5 VDC
Load voltage
CJ2
50 mA
Internal resistance
CM2
D-97
Applicable load
Load voltage
5 to 40 mA
CA2
CS1
C76
C85
OUT ()
Contact
protection
box
CD-P11
CD-P12
OUT ()
Brown
Weight
(g)
Auto switch model
OUT ( )
Blue
Black line
C95
Reed switch
MB1
2.4 V or less
Indicator light
D-90
D-97
23
23
37
37
0.5
Lead wire length
(m)
D-97
MB
24 VDC
OUT ( )
CG1
Relay, PLC
CP95
NCM
NCA
Reed switch
Choke coil
LED
Zener
diode
Zener
diode
OUT ()
Resistor
OUT (+)
Brown
OUT (+)
Black line
Dimensions
D-
D-90
-X
OUT ()
Blue
20-
Data
D-97
Indicator light
(Negative) polarity indication
Black line
6-16-21
Reed Switch
Direct Mounting Style
D-90A/D-93A
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Lead wire: Heavy-duty cord
Load voltage
24 VAC
12 VDC
24 VAC
24 VDC
100 VAC
100 VDC
50 mA
Internal resistance
20 mA
D-93A
Applicable load
Relay, PLC
Load voltage
Load current
24 VDC
range (3)
5 to 40 mA
Contact
protection
box
CD-P11
CD-P12
Lead wire Oil resistant vinyl heavy-duty cord, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
OUT()
Brown
(g)
Reed switch
D-90A
OUT( )
Blue
D-90A
D-93A
Reed switch
Brown
LED
Resistor Blue
Contact
protection
box
CD-P11
CD-P12
OUT (+)
Brown
OUT ()
Blue
47
47
77
77
Dimensions
D-90A
D-93A
Indicator light
6-16-22
D-93A
0.5
Lead wire length
(m)
Zener diode
5 to 20 mA
2.4 V or less
Indicator light
100 VAC
Reed Switch
Direct Mounting Style
D-Z73/D-Z76/D-Z80
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-Z76
Relay, PLC
IC circuit
24 VDC
100 VAC
4 to 8 VDC
5 to 40 mA
5 to 20 mA
20 mA
CJ1
CJP
CJ2
None
Indicator light
0.8 V or less
CM2
CG1
D-Z80
AC
24 V DC
or less
AC
48 V DC
AC
100 V DC
50 mA
40 mA
20 mA
Brown
Contact
protection
box
CD-P11
CD-P12
Resistor
Reed switch
OUT (+)
Brown
Zener diode
CA2
Internal resistance
LED
MB1
None
MB
Applicable load
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m (For only D-Z73, 2.7, 0.18 mm2, 2 cores)
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
OUT ()
Blue
CP95
Weight
(g)
D-Z76
10
50
55
49
()
NCA
D-X
Dimensions
D-Z73
OUT ( )
Blue
30.5
2.3
6.2
Indicator light
D-Z80 without indicator light
2.5
6.2
Indicator light
5.7
OUT()
Brown
20-
D-Z76, Z80
12.5
Most sensitive
position
2.7
D-Z80
Contact
protection
box
CD-P11
CD-P12
NCM
D-Z80
31
5.5
Reed switch
D-Z76
DC power supply
Blue
Reed switch
D-Z73
3
0.5
Lead wire length
(m)
(+)
Resistor
Load
OUT
Reverse
Black
current
prevention
diode
DC ()
C85
C95
C76
Blue
LED
CS1
12.5
Most sensitive
position
6-16-23
Data
Reed Switch
Direct Mounting Style
D-E73A/D-E76A/D-E80A
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-E76A
Relay, PLC
Load voltage
Max. load current and load current range (3)
IC circuit
24 VDC
100 VAC
4 to 8 VDC
5 to 40 mA
5 to 20 mA
20 mA
None
2.4 V or less
0.8 V or less
Applicable load
Load voltage
Maximum load current
AC
24 V DC
or less
AC
48 V DC
AC
100 V DC
50 mA
40 mA
20 mA
None
Internal resistance
Brown
Reed switch
OUT (+)
Brown
Contact
protection
box
CD-P11
CD-P12
Resistor
Zener diode
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
OUT ()
Blue
Blue
(g)
D-E73A
D-E76A
D-E80A
0.5
10
11
10
47
55
47
D-E76A
LED
DC (+)
Brown
(+)
Reed switch
Resistor
Reverse
current
prevention
diode
OUT
Black
Load
DC power supply
Dimensions
()
DC ()
Blue
D-E80A
Indicator light
Contact
protection
box
CD-P11
CD-P12
OUT ()
Brown
Reed switch
OUT ( )
Blue
8-30-18
2.7 through
Most sensitive position
Reed Switch
Direct Mounting Style
D-R73/D-R80
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Electrical entry: In-line
D-R731, D-R732
D-R801, D-R802
Relay, PLC
100 VAC
24 VDC
AC
24 V DC
or less
AC
48 V DC
AC
100 V DC
5 to 20 mA
5 to 40 mA
50 mA
40 mA
20 mA
None
None
2.4 V or less
None
Lead wire Oil resistant vinyl heavy-duty cord 0.2 mm2, 2-wire (Brown, Blue) 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 11-11-5.
Note 2) Regarding the lead wire length, refer to page 11-11-5.
D-2
D-1
Dimensions
D-R731: Right-hand mounting
Left-hand mounting
Right-hand mounting
Most sensitive position
Brown
Contact
protection
box
CD-P11
CD-P12
Reed switch
Resistor
Zener
diode
D-R801, D-R802
Reed switch
OUT ()
Blue
Blue
Contact
protection
box
CD-P11
CD-P12
OUT (+)
Brown
OUT ()
Blue
Arm
11-11-14
Arm
Reed Switch
Direct Mounting Style
D-R73 C/D-R80 C
Connector
Electrical entry: In-line
D-R801C, D-R802C
Relay, PLC
Relay, PLC
24 VDC
AC
24 V DC
or less
5 to 40 mA
50 mA
None
None
Applicable load
Load voltage
Load current range
Contact protection circuit
Internal voltage drop
Indicator light
D-R731C, D-R732C
2.4 V or less
None
CRBU2
CRB1
MSU
Lead wire Oil resistant vinyl heavy-duty cord 3.4, 0.2 mm2
Note 1) Regarding the common specifications of the reed switches, refer to page 11-11-5.
Note 2) Regarding the lead wire length, refer to page 11-11-5.
Caution
Precautions
Confirm that there is no looseness after wiring.
The looseness will decrease water resistance.
CRA1
MSQ
MRQ
D-C
CRJ
CRQ2
Dimensions
D-R731C: Right-hand mounting
CRB2
D-C
D20-
Left-hand mounting
Right-hand mounting
Most sensitive position
Brown
Contact
protection
box
CD-P11
CD-P12
Reed switch
Resistor
Zener
diode
OUT (+)
Brown
OUT ()
Blue
Blue
Reed switch
D-R801, D-R802
Contact
protection
box
CD-P11
CD-P12
OUT ()
Brown
~
OUT ()
Blue
Precautions
Be sure to read before handling.
Refer to pages 11-13-3 to 4 for
Safety Instructions and Common
Precautions on the products
mentioned in this catalog, and refer
to pages 11-1-4 to 6 for
Precautions on every series.
11-11-15
D-H7A1/D-H7A2/D-H7B
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-H7A2
D-H7B
3-wire
Wiring type
Output type
2-wire
NPN
PNP
Current consumption
10 mA or less
Applicable load
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Main circuit
of switch
DC (+)
Brown
OUT
Black
Weight
(g)
D-H7A1
D-H7A2
D-H7B
0.5
13
13
11
57
57
50
92
92
81
DC ()
Blue
Dimensions
D-H7A2
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
Indicator light
D-H7B
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
8-30-22
D-G59/D-G5P/D-K59
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-H7
D-G5
l
(with
, D-K59
indicator
(Withlight)
indicator light)
D-G59
D-K59
D-G5P
Wiring type
Output type
NPN
Applicable load
Power supply voltage
Current consumption
MX
2-wire
3-wire
MTS
PNP
MY
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
MG
CX
Indicator light
D-
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
(g)
D-G59
D-G5P
D-K59
0.5
20
20
18
78
78
68
124
124
108
Dimensions
D-G5P
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
Indicator light
3.5 mounting hole
D-K59
OUT (+)
Brown
Main circuit
of switch
-X
20Data
Weight
CY
8-30-23
D-H7C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Connector
2-wire
Output type
Applicable load
Current consumption
Load voltage
Load current
5 to 40 mA
Caution
Precautions
1. Confirm that the connector is appropriately
tightened. If tightened insufficiently, the
waterproof performance will deteriorate.
2. Refer to page 8-30-55 for the details.
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
(g)
Main circuit
of switch
D-H7C
OUT ()
Blue
4 V or less
Leakage current
0.5
15
54
85
Dimensions
Indicator light
8-30-24
D-G39/D-K39
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Terminal conduit
CJP
CJ2
10 mA or less
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA of load current)
5 to 40 mA
Leakage current
Precautions
CJ1
Load voltage
Indicator light
2-wire
NPN
Current consumption
Caution
D-K39
3-wire
IC circuit, Relay, PLC
Applicable load
Power supply voltage
D-G39
CM2
CG1
4 V or less
MB
MB1
Note) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
CA2
CS1
C76
Main circuit
of switch
DC (+)
Terminal no. 1
Weight
C85
(g)
D-G39
Lead wire
D-K39
116
C95
CP95
116
OUT
Terminal no. 2
NCM
NCA
DC ()
Terminal no. 3
Dimensions
DTightening gland
D-K39
-X
OUT (+)
Terminal no. 1
Main circuit
of switch
20G 1/2
(Applicable cable O.D.
6.8 to 9.6)
Data
OUT ()
Terminal no. 2
Indicator light
6-16-31
D-G39A/D-K39A
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Terminal conduit
D-G39A, D-K39A
D-G39A
D-K39A
Wiring type
3-wire
2-wire
Output type
NPN
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA of load current)
5 to 40 mA
Applicable load
Caution
Leakage current
Precautions
Main circuit
of switch
Indicator light
4 V or less
Note) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Weight
(g)
D-G39A
None
D-K39A
110
110
OUT
Terminal no. 2
DC ()
Terminal no. 3
Dimensions
G 1/2
(Applicable cable O.D.
6.8 to 9.6)
D-K39A
Main circuit
of switch
OUT (+)
Terminal no. 1
Tightening gland
OUT ()
Terminal no. 2
Indicator light
6-16-32
D-F79/D-F7P/D-J79
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-J79
D-F7P
Output type
MX
2-wire
3-wire
Wiring type
NPN
MTS
PNP
Current consumption
10 mA or less
Applicable load
Load voltage
Load current
Internal voltage drop
28 VDC or less
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
Leakage current
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
CY
MG
Indicator light
MY
CX
D-
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
-X
20Data
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
Weight
(g)
D-F79
D-F7P
D-J79
0.5
13
13
11
57
57
50
92
92
81
Dimensions
3.5 mounting hole
D-F7P
Indicator light
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-J79
Most sensitive position
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
8-30-25
D-F7NV/D-F7PV/D-F7BV
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Electrical entry: Perpendicular
D-F7PV
D-F7BV
3-wire
Wiring type
Output type
2-wire
NPN
PNP
Current consumption
10 mA or less
Applicable load
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
Weight
(g)
D-F7NV
D-F7PV
D-F7BV
0.5
13
13
11
57
57
50
92
92
81
Dimensions
3.5 mounting hole
D-F7PV
Indicator light
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-F7BV
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
8-30-26
D-J79C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Connector
D-J79C
Auto switch model
D-J79C
Wiring type
Output type
Current consumption
Load voltage
Load current
5 to 40 mA
Precautions
1. Confirm that the connector is appropriately
tightened. If tightened insufficiently, the
waterproof performance will deteriorate.
2. Refer to page 8-30-55 for the details.
MTS
Applicable load
Caution
MX
2-wire
MY
CY
4 V or less
Leakage current
Indicator light
MG
CX
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
D-X
20Data
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
Weight
(g)
D-J79C
0.5
13
52
83
Dimensions
3.2 mounting hole
Indicator light
8-30-27
D-F59/D-F5P/D-J59/D-J51
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-F5, D-J5
D-F59
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-F5P
D-J59
D-J51
2-wire
NPN
AC Relay, PLC
Current consumption
10 mA or less
Applicable load
D-F5P
3-wire
Wiring type
PNP
Load voltage
28 VDC or less
80 to 260 VAC
Load current
40 mA or less
80 mA or less
5 to 40 mA
5 to 80 mA
0.8 V or less
4 V or less
14 V or less
1.5 V or less
Internal voltage drop (0.8 V or less at
10 mA load current)
Leakage current
Indicator light
0.8 mA or less
at 24 VDC
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Weight
Main circuit
of switch
DC (+)
Brown
(g)
D-F59
D-F5P
D-J59
D-J51
0.5
23
23
21
21
81
81
71
71
127
127
111
111
DC ()
Blue
Dimensions
D-J59
Mounting hole
Main circuit
of switch
OUT (+)
Brown
Indicator light
OUT ()
Blue
Main circuit
of switch
D-J51
OUT
Brown
OUT
Blue
6-16-36
D-G39C/D-K39C
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Terminal conduit
D-G39C, D-K39C
Auto switch model
Wiring
Output
CJ1
CJP
NPN
Power voltage
10 mA or less
Load voltage
28 VDC or less
Load voltage
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA of load current)
5 to 40 mA
Current leakage
2-wire
Precautions
D-K39C
3-wire
Applicable load
Current consumption
Caution
D-G39C
Indicator light
CJ2
CM2
CG1
4 V or less
MB
MB1
Note) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
CA2
Weight
(g)
D-G39C
D-K39C
40
162
162
50
166
166
63
184
184
80
210
210
100
232
232
Main circuit
of switch
DC (+)
Terminal no. 1
OUT
Terminal no. 2
C76
C85
C95
CP95
Dimensions
NCM
2-M5 x 0.8 x 12
Hexagon socket head cap bolt
NCA
DC ()
Terminal no. 3
D-
D-K39C
-X
Tightening gland
20-
Hexagon socket
head cap bolt
Main circuit
of switch
OUT (+)
Terminal no. 1
CS1
Data
G 1/2
(Applicable cable O.D.
6.8 to 9.6)
OUT ()
Terminal no. 2
Indicator light
Most sensitive position
Dimensions
Auto switch model
D-G39C-4, D-K39C-4
D-G39C-5, D-K39C-5
D-G39C-6, D-K39C-6
D-G39C-8, D-K39C-8
D-G39C-10, D-K39C-10
Applicable bore
size (mm)
40
50
63
80
100
HW
44 69 57
52 77 58
64 91 60.5
78 107 64
92 121 67
49.5
50.5
52
53.5
56.5
7.5
8.5
10.5
12.5
15.5
6.5
M5 x 0.8 x 16
6.5
7.5 M5 x 0.8 x 20
9.5
M5 x 0.8 x 25
9.5
6-16-37
D-M9N(V)/D-M9P(V)/D-M9B(V)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-M9N
D-M9NV
D-M9P
D-M9PV
D-M9B
D-M9BV
In-line
Perpendicular
In-line
Perpendicular
In-line
Perpendicular
2-wire
3-wire
Wiring type
NPN
Output type
PNP
Current consumption
10 mA or less
Applicable load
28 VDC or less
Load voltage
Load current
40 mA or less
0.8 V or less
4 V or less
0.8 mA or less
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 2.7 x 3.2 ellipse 0.15 mm2, 2 cores (D-M9B), 3
cores (D-M9N, D-M9P)
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
8
41
41
38
68
68
63
Dimensions
D-M9V
M2.5 x 4l
Slotted set screw
2
2.8
2.7
4
2.8
OUT
Black
Indicator light
8
3.2
2.6
D-M9
22
500 (3000)
9.5
DC ()
Blue
D-M9B(V)
0.5
Indicator light
DC (+)
Brown
D-M9P(V)
4.6
D-M9P, D-M9PV
Main circuit
of switch
OUT
Black
DC ()
Blue
D-M9N(V)
2.7
3.2
Main circuit
of switch
DC (+)
Brown
(g)
2.6
D-M9B, D-M9BV
Precautions
Main circuit
of switch
OUT (+)
Brown
8-30-28
Caution on Handling
Caution
Over-current protection is not equipped with this product series. When it is
wired incorrectly or a load is short-circuited, a switch may be damaged or
burned.
In the event of stripping cable sheath, use caution for the stripping direction.
Its insulation may be torn or damaged, depending on the direction.
Below is given as the recommended tool.
Maker
Products name
Wirestripper
VESSEL Co., Inc.
Stripmaster
Tokyo Ideal Co., Ltd.
Part no.
No 3000G
45-089
Fix the switch with appropriate screw installed on the switch body. If using
other screws, switch may be damaged.
D-F9G/D-F9H
Grommet
NPN
Output type
CU
CQS
10 mA or less
Current consumption
CQM
Load voltage
28 VDC or less
Load current
40 mA or less
80 mA or less
PNP
5, 12, 24 VDC (4.5 to 28 VDC)
Precautions
CUJ
Applicable load
Caution
D-F9H
3-wire
Wiring type
1.5 V or less
CQ2
0.8 V or less
RQ
Leakage current
MU
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 2.7, 0.15 mm2, 3 cores (Brown, Black, Blue) 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 7-9-7.
Note 2) Regarding the lead wire length, refer to page 7-9-7.
D-X
20-
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
Weight
Data
(g)
D-F9G
D-F9H
37
37
61
61
Dimensions
Mounting screw M2.5 x 4l
Slotted set screw
D-F9H
22
2.8
OUT
Black
D-F9H
2.7
SMC
NC
Indicator light
DC ()
Blue
2.6
Main circuit
of switch
DC (+)
Brown
7-9-23
D-F8N/D-F8P/D-F8B
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-F8N
D-F8P
D-F8B
Perpendicular
Perpendicular
Perpendicular
3-wire
Wiring type
NPN
Applicable load
PNP
10 mA or less
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
2.5 to 40 mA
0.8 V or less
4 V or less
Leakage current
Precautions
MY
Load voltage
Caution
MTS
Output type
Current consumption
MX
2-wire
MG
CX
D-
Indicator light
-X
20Data
Weight
(g)
D-F8N
D-F8P
D-F8B
32
32
32
52
52
52
Dimensions
D-F8N, D-F8P, D-F8B
D-F8P
4.3
Indicator light
2
2.7
OUT
Black
10
4.6
2.8
Main circuit
of switch
DC (+)
Brown
DC ()
Blue
10.9
D-F8B
Main circuit
of switch
3.1
OUT (+)
Brown
CY
OUT ()
Blue
8-30-29
Grommet
D-Y59A
D-Y69A
D-Y7P
D-Y7PV
D-Y59B
D-Y69B
In-line
Perpendicular
In-line
Perpendicular
In-line
Perpendicular
3-wire
Wiring type
2-wire
NPN
Output type
PNP
Current consumption
10 mA or less
Applicable load
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.15 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
(g)
OUT
Black
0.5
Lead wire length
(m)
DC ()
Blue
D-Y7P, D-Y7PV
10
10
50
53
53
83
87
87
OUT
Black
2.5
6.2
SMC
SMC
Indicator light
2.5
6.2
DC ()
Blue
27.3
D-Y59B, D-Y69B
29
3.4
8.5
Main circuit
of switch
OUT (+)
Brown
12.5
OUT ()
Blue
8-30-30
D-Y7P(V)
Dimensions
DC (+)
Brown
Main circuit
of switch
3.4
Main circuit
of switch
DC (+)
Brown
12.5
D-Y7G/D-Y7H
Grommet
D-Y7H
Wiring type
3-wire
Output type
NPN
PNP
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
80 mA or less
1.5 V or less
0.8 V or less
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.15 mm2, 3 cores (Brown, Black, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
D-Y7G
(g)
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-Y7G
D-Y7H
0.5
10
10
53
53
87
87
Dimensions
SMC
OUT
Black
Indicator light
2.5
6.2
Main circuit
of switch
DC (+)
Brown
NC
29
DC ()
Blue
D-Y7G
12.5
8-30-32
3.4
D-Y7H
D-M5N/D-M5P/D-M5B
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-M5P
3-wire
Wiring type
Output type
2-wire
NPN
Applicable load
Power supply voltage
RE BA
D-M5B
REC
PNP
10 mA or less
Current consumption
CX
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Indicator light
CY
MQ MQ
RHC
MK(2)
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
RS QG
RS AH
RZQ
Main circuit
of switch
DC (+)
Brown
OUT
Black
MI WS
Weight
(g)
D-M5N
D-M5P
D-M5B
0.5
16
16
14
60
60
53
95
95
84
CEP1
CE1
CE2
ML2B
DC ()
Blue
Dimensions
C GJ 5-S
Indicator light
D-M5P
CV
Main circuit
of switch
DC (+)
Brown
MVGQ
CC
OUT
Black
DC ()
Blue
RB
3 mounting hole
D-M5B
D-X
Main circuit
of switch
OUT (+)
Brown
20Data
OUT ()
Blue
10-20-39
D-S99(V)/D-S9P(V)/D-T99(V)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
2-wire
3-wire
D-T99
D-S99
D-S9P
D-2
D-S99V1
D-S9P1
D-S9PV1
D-S99V2
D-S9P2
D-S9PV2
Perpendicular
In-line
Perpendicular
3-wire
NPN
PNP
IC circuit, Relay, PLC
5, 12, 24 VDC (4.5 to 28 VDC)
10 mA or less
28 VDC or less
40 mA or less
80 mA or less
1.5 V or less
(0.8 V or less
at load current 10 mA)
D-1
D-S991
D-S992
In-line
D-T991
D-T99V1
D-T992
D-T99V2
In-line
Perpendicular
2-wire
24 VDC relay, PLC
0.8 V or less
4 V or less
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord 3.4, 0.2 mm2, 3-wire (Brown, Black, Blue),
2-wire (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 11-11-5.
Note 2) Regarding the lead wire length, refer to page 11-11-5.
Right-hand mounting
D-V2
Left-hand mounting
3.4
Mounting hole
DC (+)
Brown
Main circuit
of switch
3.4
D-V1
Dimensions
3.4
OUT
Black
DC ()
Blue
D-S9P(V)1, D-S9P(V)2
Main circuit
of switch
DC (+)
Brown
Mounting hole
OUT
Black
DC ()
Blue
D-T99(V)1, D-T99(V)2
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
11-11-22
3.4
Mounting hole
D-S79/D-S7P/D-T79(C)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet, Connector
Electrical Entry: In-line
Wiring type
Output type
Applicable load
Power supply voltage
3-wire
NPN
28 VDC or less
Left-hand mounting
D-1
Right-hand mounting
CRB1
MSU
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA)
5 to 40 mA
CRJ
0.8 V or less
4 V or less
CRA1
CRQ2
Indicator light
D-2
CRBU2
10 mA or less
Load voltage
Leakage current
2-wire
PNP
Current consumption
Lead wire Oil resistant vinyl heavy-duty cord 3.4, 0.2 mm2, 3-wire (Brown, Black, Blue),
2-wire (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 11-11-5.
Note 2) Regarding the lead wire length, refer to page 11-11-5.
MSQ
Dimensions
D-
D-S791, D-S792
Main circuit
of switch
DC (+)
Brown
OUT
Black
D-S7P1, D-S7P2
DC (+)
Brown
Main circuit
of switch
OUT
Black
DC ()
Blue
D-T791(C), D-T792(C)
CRB2
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
11-11-23
MRQ
20-
6-15-36
D-B59W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
Relay, PLC
Load voltage
24 VDC
5 to 40 mA
Built-in
4 V or less
Operating positionRed LED lights when ON.
Optimum operating positionGreen LED lights when ON.
Indicator light
Weight
OUT (+)
Brown
Reed switch
Zener diode
Main circuit
of switch
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
(g)
LED
D-B59W
OUT ()
Blue
0.5
20
76
Dimensions
Operating range
Indication
Red
Green
Red
Indicator light
6-16-24
D-H7NF
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Since the output signal can be
detected in an unsteady detecting
area, the difference of detecting
position can be confirmed by the
side of PLC (Programmable Logic
Controller).
4-wire
Output
NPN
Diagnostic output
Normal operation
IC circuit, Relay, PLC
Power voltage
Load current
MG
CX
D-
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 4 cores (Brown, Black, Orange,
Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
(g)
Diagnosis OUT
(Diagnostic output)
Orange
DC ()
Blue
-X
20Data
Weight
D-H7NF
0.5
13
56
90
Indicator light
OFF
Red
ON
Green
Red
OFF
Red
OUT
(Normal output)
Diagnosis OUT
(Diagnostic output)
Dimensions
3.4
Main circuit
of switch
CY
Load voltage
Current leakage
MY
10 mA or less
DC (+)
Brown
MTS
Applicable load
Current consumption
MX
D-H7NF
Wiring
Indicator light
3.5 mounting hole
8-30-39
D-G59F
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Since the output signal can be
detected in an unsteady detecting
area, the difference of detecting
position can be confirmed by the
side of PLC (Programmable Logic
Controller).
4-wire
Output
NPN
Diagnostic output
Normal operation
Applicable load
Power voltage
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
Current leakage
Indicator light
DC (+)
Brown
Main circuit
of switch
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.2 mm2, 4 cores (Brown, Black, Orange,
Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
(g)
Auto switch model
Lead wire length
(m)
D-G59F
0.5
20
74
117
OFF
Indicator light
Red
ON
Green
OUT
(Normal output)
Diagnosis OUT
(Diagnostic output)
Dimensions
Indicator light
8-30-40
Red
OFF
Red
D-F79F
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Since the output signal can be
detected in an unsteady detecting
area, the difference of detecting
position can be confirmed by the
side of PLC (Programmable Logic
Controller).
4-wire
Output
NPN
Diagnostic output
Normal operation
MY
Power voltage
Load voltage
28 VDC or less
Load current
MG
D-
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 4 cores (Brown, Black, Orange, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 8-30-7.
Note 2) Regarding the lead wire length, refer to page 8-30-7.
Weight
(g)
D-F79F
DC ()
Blue
0.5
13
56
90
-X
20Data
ON
Indicator light
OFF
Red
Green
Red
OFF
Red
OUT
(Normal output)
Diagnosis OUT
(Diagnostic output)
Dimensions
3.2 mounting hole
Indicator light
3.4
Main circuit
of switch
CX
Current leakage
Diagnosis OUT
(Diagnostic output)
Orange
CY
10 mA or less
DC (+)
Brown
MTS
Applicable load
Current consumption
MX
D-F79F
Wiring
8-30-41
D-F59F
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Since the output signal can be
detected in an unsteady detecting
area, the difference of detecting
position can be confirmed by the
side of PLC (Programmable Logic
Controller).
D-F59F
Wiring type
4-wire
Output type
NPN
Diagnostic output
Normal operation
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
Leakage current
Indicator light
DC (+)
Brown
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.2 mm2, 4 cores (Brown, Black, Orange, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 11-11-5.
Note 2) Regarding the lead wire length, refer to page 11-11-5.
Weight
Main circuit
of switch
(g)
D-F59F
DC ()
Blue
0.5
22
77
121
ON
OFF
Indicator light
Red
Green
OUT
(Normal output)
Diagnosis OUT
(Diagnostic output)
Dimensions
Mounting hole
Indicator light
11-11-28
Red
OFF
Red
D-H7NW/D-H7PW/D-H7BW
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
0.8 mA or less at 24 VDC
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
OUT
Black
Weight
DC ()
Blue
(g)
D-H7NW
D-H7PW
D-H7BW
0.5
13
13
11
57
57
50
92
92
81
D-H7PW
Main circuit
of switch
DC (+)
Brown
OUT
Black
Dimensions
DC ()
Blue
D-H7BW
Main circuit
of switch
OUT (+)
Brown
Indicator light
3.5 mounting hole
OUT ()
Blue
Operating range
Indication
Red
Green
Red
6-16-40
Main circuit
of switch
2-wire
PNP
NPN
Applicable load
DC (+)
Brown
D-H7BW
3-wire
Output type
D-H7PW
D-H7NW
Wiring type
D-G59W/D-G5PW/D-K59W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
D-G59W
Main circuit
of switch
OUT
Black
DC ()
Blue
10 mA or less
CJ2
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Leakage current
Indicator light
MB
MB1
Main circuit
of switch
CA2
CS1
C76
Weight
C85
(g)
D-G59W
D-G5PW
D-K59W
0.5
20
20
18
78
78
68
124
124
108
DC (+)
Brown
OUT
Black
CM2
CG1
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
D-G5PW
CJP
PNP
Load voltage
DC (+)
Brown
2-wire
NPN
Applicable load
CJ1
D-K59W
3-wire
Output type
D-G5PW
Wiring type
C95
CP95
NCM
NCA
Dimensions
D-
DC ()
-X
Blue
20D-K59W
Data
OUT (+)
Brown
Main circuit
of switch
Indicator light
4.5 mounting hole
OUT ()
Blue
Indication
Red
Green
Red
6-16-41
D-A79W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
5 to 40 mA
4 V or less
Operating positionRed LED lights when ON.
Optimum operating positionGreen LED lights when ON.
Indicator light
Main circuit
of switch
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
MB
MB1
CA2
C76
D-A79W
OUT ()
Blue
CG1
(g)
LED
CM2
CS1
OUT (+)
Brown
Reverse flow
prevent diode
CJ2
None
Reed switch
CJP
24 VDC
CJ1
Relay, PLC
0.5
11
53
C85
C95
CP95
Dimensions
NCM
Operating range
Indication
Red
NCA
Green
Red
-X
20Data
Most sensitive position
6-16-25
D-F79W/D-F7PW/D-J79W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
D-F7W, D-J79W
D-F79W
D-F7PW
Wiring type
Output type
2-wire
Current consumption
10 mA or less
Load voltage
28 VDC or less
40 mA or less
1.5 V or less
(0.8 V or less
Internal voltage drop
at 10 mA load current)
80 mA
5 to 40 mA
0.8 V or less
4 V or less
Leakage current
Main circuit
of switch
OUT
Black
Load current
DC (+)
Brown
PNP
NPN
Applicable load
D-J79W
3-wire
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
Weight
(g)
DC ()
Blue
D-F7PW
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-F79W
D-F7PW
D-J79W
0.5
13
13
11
57
57
50
92
92
81
Dimensions
3.2 mounting hole
Indicator light
D-J79W
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
Operating range
Indication
Red
Green
Red
6-16-42
D-F7NWV/D-F7BWV
For details about the applicable products
conforming to the standards applied in
some countries, refer to SMCs web site.
Grommet
Electrical entry: Perpendicular
D-F7NWV
D-F7BWV
Wiring type
3-wire
2-wire
Output type
NPN
Applicable load
Power supply voltage
CJ1
CJP
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
5 to 40 mA
CJ2
CM2
CG1
4 V or less
MB
MB1
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
CA2
CS1
C76
Weight
C85
(g)
D-F7NWV
D-F7BWV
0.5
13
11
57
50
92
81
DC (+)
Brown
OUT
Black
DC ()
Blue
CP95
NCM
NCA
Dimensions
D-F7BWV
-X
Indicator light
OUT (+)
Brown
Main circuit
of switch
20Data
OUT ()
Blue
Operating range
C95
Red
6-16-43
D-A59W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
Relay, PLC
Load voltage
5 to 40 mA
4 V or less
Operating positionRed LED lights when ON.
Optimum operating positionGreen LED lights when ON.
Indicator light
Zener diode
Main circuit
of switch
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the reed switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Note 3) Under 5 mA, the strength of the indicator light is poor. In some cases, visibility of the
indicator light will not be possible where the output signal is less than 2.5 mA. However,
there is no problem in terms of contact output, when an output signal exceeds 1 mA or
more.
Weight
Auto switch model
OUT ()
Blue
MQ MQ
RHC
MK(2)
RS QG
(g)
LED
CY
RS AH
OUT (+)
Brown
Reed switch
CX
None
Choke coil
REC
24 VDC
RE BA
D-A59W
RZQ
D-A59W
0.5
25
80
MI WS
CEP1
CE1
Dimensions
CE2
Operating range
Indication
Red
ML2B
Green
Red
C GJ 5-S
Optimum operating position
CV
MVGQ
Indicator light
CC
RB
J
Most sensitive position
D-X
20Data
10-20-25
D-F59W/D-F5PW/D-J59W
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
D-F5PW
Wiring type
Output type
PNP
Current consumption
10 mA or less
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
Internal voltage drop
at 10 mA load current)
Main circuit
of switch
Indicator light
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Leakage current
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
OUT
Black
Weight
DC ()
Blue
(g)
D-F59W
D-F5PW
D-J59W
0.5
23
23
21
81
81
71
127
127
111
D-F5PW
Main circuit
of switch
DC (+)
Brown
OUT
Black
DC ()
Blue
D-J59W
Dimensions
Mounting hole
Indicator light
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
Indication
Red
Green
Red
6-16-44
Load voltage
DC (+)
Brown
2-wire
NPN
Applicable load
D-J59W
3-wire
D-F9NW(V)/D-F9PW(V)/D-F9BW(V)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
D-F9NW
D-F9NWV
D-F9PW
D-F9PWV
D-F9BW
D-F9BWV
In-line
Perpendicular
In-line
Perpendicular
In-line
Perpendicular
NPN
Current consumption
10 mA or less
OUT
Black
DC ()
Blue
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
RHC
0.8 mA or less
MK(2)
Leakage current
Indicator light
Weight
Main circuit
of switch
RZQ
(g)
D-F9NW(V)
D-F9PW(V)
D-F9BW(V)
34
34
32
56
56
52
0.5
DC (+)
Brown
Dimensions
Mounting screw M2.5 x 4l
Slotted set screw
DC ()
Blue
Indicator light
D-F9BW, D-F9BWV
CE1
CE2
CV
MVGQ
22
2.8
2.6
C GJ 5-S
CC
Main circuit
of switch
OUT (+)
Brown
CEP1
ML2B
D-F9W
OUT ()
Blue
RS AH
MI WS
OUT
Black
MQ MQ
RS QG
Lead wire Oil resistant vinyl heavy-duty cord: 2.7, 3 cores (Brown, Black, Blue), 0.15 mm2
2 cores (Brown, Blue) 0.18 mm2, 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
D-F9PW, D-F9PWV
CY
2.7
Main circuit
of switch
DC (+)
Brown
CX
Load voltage
PNP
IC circuit, Relay, PLC
Applicable load
REC
2-wire
3-wire
RE BA
RB
J
D-F9WV
D-
4.3
-X
Indicator light
20Red
2.8
Data
3.1
6.2
Indication
Green
Red
20
3.8
2.7
4.6
Operating range
4
6
10-20-47
D-Y7NW(V)/D-Y7PW(V)/D-Y7BW(V)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Perpendicular
Main circuit
of switch
Main circuit
of switch
DC (+)
Brown
OUT
Black
10 mA or less
CJ2
CM2
Load voltage
28 VDC or less
Load current
40 mA or less
1.5 V or less
(0.8 V or less
at 10 mA load current)
80 mA or less
5 to 40 mA
0.8 V or less
4 V or less
Indicator light
Weight
C76
C85
D-Y7NW(V)
D-Y7PW(V)
D-Y7BW(V)
0.5
11
11
11
54
54
54
88
88
88
Dimensions
Mounting screw M2.5 x 4l
Slotted set screw
Indicator light
NCM
-X
20-
29
Data
OUT (+)
Brown
Main circuit
of switch
CP95
D-
SMC
6.2
D-Y7BW, D-Y7BWV
C95
NCA
2.5
12.5
D-Y7WV
SMC
6.2
2.5
Operating range
27.3
Red
3.4
8.5
Indication
Green
Red
CS1
(g)
D-Y7W
MB1
CA2
Lead wire Oil resistant, flexible vinyl heavy-duty cord, 3.4, 0.15 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue), 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
DC ()
Blue
OUT ()
Blue
CG1
MB
D-Y7PW, D-Y7PWV
CJP
Current consumption
Leakage current
CJ1
Perpendicular
DC ()
Blue
PNP
Applicable load
OUT
Black
In-line
2-wire
NPN
Output type
DC (+)
Brown
Perpendicular
3-wire
Wiring type
In-line
3.4
Grommet
The optimum operating position
can be determined by the color
of the light. (Red Green Red)
12.5
6-16-45
D-M5NW/D-M5PW/D-M5BW
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
The optimum operating position
can be determined by the color
of the light.
(Red Green Red)
D-M5NW
D-M5PW
Wiring type
D-M5BW
3-wire
Output type
PNP
NPN
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
40 mA or less
80 mA or less
1.5 V or less
Internal voltage drop
(0.8 V or less
0.8 V or less
at 10 mA load current)
Leakage current
100 A or less at 24 VDC
D-M5NW
Indicator light
REC
CX
Load current
RE BA
2-wire
MQ MQ
4 V or less
1 mA or less at 24 VDC
Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue),
2 cores (Brown, Blue) 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Main circuit
of switch
OUT
Black
(g)
Auto switch model
Lead wire length
(m)
D-M5PW
D-M5NW
D-M5PW
D-M5BW
0.5
16
16
14
60
60
53
95
95
84
Main circuit
of switch
DC (+)
Brown
RS AH
MI WS
CEP1
CE1
CE2
Dimensions
OUT
Black
RS QG
RZQ
Weight
DC ()
Blue
RHC
MK(2)
Lead wire
DC (+)
Brown
CY
5 to 40 mA
ML2B
Indicator light
C GJ 5-S
DC ()
Blue
CV
D-M5BW
MVGQ
CC
Main circuit
of switch
OUT (+)
Brown
RB
3 mounting hole
J
OUT ()
Blue
D-X
20-
Operating range
Indication
Red
Green
Data
Red
10-20-49
6-15-36
6-15-36
6-15-36
6-15-36
D-G5NTL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
With built-in OFF-delay timer (200 ms)
3-wire
Output type
NPN
Output operation
Off-delay
Operating time
1 ms or less
Off-delay time
200 50 ms
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue), 3 m
(Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
D-G5NT
0.5
Main circuit
of switch
DC (+)
Brown
78
124
Timer Operation
Detection of intermediate positioning for high-speed cylinder
OUT
Black
DC ()
Blue
Dimensions
Indicator light
10-20-60
D-F7NTL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
With built-in OFF-delay timer (200 ms)
RE BA
D-F7NTL
3-wire
Output type
REC
NPN
Output operation
Off-delay
Operating time
CX
1 ms or less
Off-delay time
200 50 ms
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
CY
MQ MQ
RHC
MK(2)
Leakage current
Indicator light
RS QG
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue), 3 m
(Standard)
Note 1) For the solid state switch common specifications, refer to page 10-20-7.
Note 2) For lead wire length, refer to page 10-20-7.
Weight
RS AH
RZQ
MI WS
(g)
Auto switch model
0.5
57
92
CE1
CE2
Timer Operation
ML2B
DC ()
Blue
C GJ 5-S
CV
MVGQ
PLC response time
CC
RB
Dimensions
D-X
20-
3.4
Main circuit
of switch
DC (+)
Brown
CEP1
D-F7NT
Data
10-20-61
D-F5NTL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
With built-in OFF-delay timer (200 ms)
3-wire
Output type
NPN
Output operation
Off-delay
Operating time
1 ms or less
Off-delay time
200 50 ms
Applicable load
Current consumption
10 mA or less
Load voltage
28 VDC or less
Load current
40 mA or less
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue), 3 m
(Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
Auto switch model
Main circuit
of switch
DC (+)
Brown
D-F5NT
0.5
81
127
Timer Operation
Detection of intermediate positioning for high-speed cylinder
OUT
Black
DC ()
Blue
Dimensions
Mounting hole
Indicator light
10-20-62
D-M5NTL/D-M5PTL
For details about the applicable products
conforming to the standards applied in
some countries, refer to SMCs web site.
Grommet
With built-in OFF-delay timer (200 ms)
D-M5NTL
Wiring type
D-M5PTL
RE BA
PNP
REC
3-wire
Output type
NPN
Output operation
Off-delay
Operating time
CX
1 ms or less
Off-delay time
200 50 ms
Applicable load
CY
Current consumption
Load voltage
10 mA or less
12 mA or less
28 VDC or less
Load current
MQ MQ
RHC
80 mA or less
2 V or less
MK(2)
0.8 V or less
Leakage current
Indicator light
RS QG
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores (Brown, Black, Blue), 3 m
(Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
(g)
D-M5NT
D-M5PT
0.5
60
60
95
95
DC ()
Blue
Main circuit
of switch
DC (+)
Brown
CE1
ML2B
Timer Operation
OUT
Black
CEP1
CE2
C GJ 5-S
CV
MVGQ
CC
RB
Dimensions
J
Indicator light
OUT
Black
D-
3.4
Main circuit
of switch
DC (+)
Brown
RZQ
MI WS
Weight
Auto Switch Internal Circuit
RS AH
-X
DC ()
Blue
20Data
3 mounting hole
10-20-63
D-H7BAL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
2-wire
Wiring type
Output type
Applicable load
Current consumption
Load voltage
Load current
5 to 40 mA
4 V or less
Caution
Leakage current
Precautions
Please consult with SMC if using coolant
liquid other than water based solution.
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 3 m (Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
D-H7BA
0.5
50
81
Dimensions
3.4
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
Indicator light
Operating range
Indication
Red
Green
Red
10-20-54
D-G5BAL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
2-wire
Output type
Load voltage
Load current
5 to 40 mA
4 V or less
Indicator light
CY
MQ MQ
RHC
MK(2)
Leakage current
CX
Current consumption
Precautions
REC
Applicable load
Caution
RE BA
D-G5BAL
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 3 m (Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
RS AH
Weight
(g)
Auto switch model
68
108
RZQ
MI WS
D-G5BA
0.5
RS QG
CEP1
CE1
CE2
ML2B
C GJ 5-S
Main circuit
of switch
OUT (+)
Brown
Dimensions
CV
OUT ()
Blue
Indicator light
MVGQ
CC
RB
Operating range
J
Indication
Red
Green
D-
Red
-X
20Data
10-20-55
D-F7BA(V)L
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
D-F7BAL
D-F7BAVL
In-line
Perpendicular
2-wire
Output type
Applicable load
Current consumption
Caution
Precautions
Load voltage
Load current
5 to 40 mA
4 V or less
0.8 mA or less at 24 VDC
Leakage current
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 2 cores (Brown, Blue), 3 m (Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
Auto switch model
Lead wire length
(m)
D-F7BA
D-F7BAV
0.5
50
50
81
81
Dimensions
D-F7BAL
15
Main circuit
of switch
OUT (+)
Brown
OUT ()
Blue
Operating range
D-F7BAVL
Red
Indicator light
SMC
Green
15
Indication
Red
23
8.5
10-20-56
6.2
11
15
3.2
3.4
D-F5BAL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
Wiring type
Applicable load
Current consumption
Load voltage
Load current
5 to 40 mA
4 V or less
Indicator light
CY
MQ MQ
RHC
MK(2)
Leakage current
CX
Precautions
REC
Output type
Caution
RE BA
D-F5BAL
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 2 cores (Brown, Blue), 3 m (Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
RS QG
RS AH
Weight
RZQ
(g)
MI WS
D-F5BA
0.5
71
111
CEP1
CE1
CE2
Main circuit
of switch
OUT (+)
Brown
Dimensions
ML2B
C GJ 5-S
Mounting hole
Indicator light
CV
OUT ()
Blue
MVGQ
Indicator light/Display method
CC
RB
Operating range
J
Indication
Red
Green
D-
Red
-X
20Data
10-20-57
D-F9BAL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
2-wire
Output type
Applicable load
Current consumption
Load voltage
Load current
5 to 30 mA
Caution
5 V or less
1 mA or less at 24 VDC
Leakage current
Precautions
Please consult with SMC if using coolant
liquid other than water based solution.
Indicator light
Lead wire Oil resistant vinyl heavy-duty cord, 2.7, 2 cores (Brown, Blue), 0.18 mm2, 0.5 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
D-F9BA
OUT (+)
Brown
0.5
37
57
Dimensions
Indicator light
OUT ()
Blue
Operating range
Red
10-20-58
2.7
Main circuit
of switch
M2.5 x 4l
Slotted set screw
D-Y7BAL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Water (coolant) resistant type
Wiring type
Load voltage
Load current
5 to 40 mA or less
0.8 mA or less at 24 VDC
CY
MQ MQ
Leakage current
Indicator light
CX
4 V or less
Precautions
REC
Applicable load
Caution
RE BA
D-Y7BAL
Lead wire Oil resistant, flexible vinyl heavy-duty cord, 3.4, 0.15 mm2, 2 cores (Brown, Blue), 3 m
(Standard)
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
MK(2)
RS QG
Weight
(g)
Auto switch model
Lead wire length
(m)
RHC
D-Y7BA
0.5
54
88
RS AH
RZQ
MI WS
CEP1
Dimensions
CE1
Mounting screw M2.5 x 4l
Slotted set screw
Indicator light
ML2B
Main circuit
of switch
OUT (+)
Brown
CE2
C GJ 5-S
CV
OUT ()
Blue
MVGQ
CC
RB
J
Indication
Red
Green
D-
Red
-X
20Data
10-20-59
6-15-36
D-P5DWL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Possible to use in an environment
where disturbance magnetic fields
are generated.
D-P5DWL
2-wire (non-polar)
Wiring type
Applicable load
Load voltage
Load current
6 to 40 mA or less
5 V or less
1 mA or less at 24 VDC
Leakage current
Operating time
40 ms or less
Operating positionRed LED lights when ON.
Optimum operating positionGreen LED lights when ON.
Indicator light
Caution
Precautions
For use with single-phase AC welders. Not
applicable for DC inverter welding, arc
welding nor capacitor welding.
Lead wire Oil resistant vinyl heavy-duty cord, 6, 0.5 mm2, 2 cores (Brown, Blue), 3 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 10-20-7.
Note 2) Regarding the lead wire length, refer to page 10-20-7.
Weight
(g)
Auto switch model
D-P5DW
0.5
150
244
OUT ()
Brown
OUT ( )
Blue
Dimensions
Indicator light
Main circuit
of switch
When the AC welding current is 16000 A or less, the operational distance between the welding
conductor (welding gun or cable) and the cylinder or auto switch can be 0 mm.
Please consult with SMC when exceeding 16000 A.
Operating range
Indication
Red
Green
Red
10-20-64
D-P3DW/L/Z
(Electrical entry: Grommet)
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Applicable load
Load voltage
Load current
6 to 40 mA
5 V or less
1 mA or less at 24 VDC
Leakage current
40 ms or less
Operating time
Indicator light
Standards
Lead wire Oilproof heavy-duty vinyl cable, 0.189, 0.775 x 103 in2, 2 cores,
D-P3DW: 19.7 in, D-P3DWL: 118 in, D-P3DWZ: 197 in
Impact resistance Switch: 39370 in/s2
Insulation resistance 50 M or more at 500 VDC Mega (between lead wire and case)
Withstand voltage 1000 VAC for 1 minute (between lead wire and case)
Ambient temperature 14 to 140F
Enclosure IEC60529 standard IP67
Polarity: Non-polar
Caution
Precautions
For single-phase AC welding machines
If it is used for current inverter welders (including
rectifying type) and condenser type welders, the
magnetic field resistance is reduced. Please contact
SMC regarding the performance.
Mass
Auto Switch Internal Circuit
D-P3DW/L/Z
Unit: lb(s)
D-P3DW/L/Z
OUT () Brown
OUT ( ) Blue
0.225
197
0.37
Dimensions
Unit: in
Body
0.236
Indicator light
ON
0.118
Red
0.126
Optimum operating
position
Most sensitive
0.413 position
(1.14)
0.157
0.244
(1.14)
0.157
OFF
Green
1.14
0.433 0.0394
Operating
range
Indication
Red
0.044
118
0.189
Switch
main circuit
19.7
When the auto switch is ordered on its own, the auto switch mounting bracket is not enclosed. In that
case, please order it separately.
D-P4DWL/D-P4DWZ
For details about certified products conforming to
international standards, visit us at www.smcworld.com.
D-P4DWZ
24 VDC relay, PLC
Applicable load
Load voltage
Load current
6 to 40 mA or less
5 V or less
1 mA or less at 24 VDC
Leakage current
40 ms or less
Operating time
Indicator light
Caution
Precautions
For single-phase AC welding machines
Not applicable for DC inverter welding
machines (including rectifying type) and or
condenser type welding.
Switch
main circuit
Dimensions
Unit: mm
Indicator light
6
OUT () Brown
SMC
8.8
9.2
OUT () Blue
D-P4DW (DC24V)
32
3000 (5000)
ON
Red
20
Indication
Green
Red
OFF
Operating
range
Optimum operating
position
13
20
D-P74
D-P75
Grommet
Relay, PLC
Electrical entry
Application
Load voltage
24VDC 100VDC
100VAC
5 to 40mA 5 to 20mA
Yes
20mA
40mA
No
(10 or less)
2.4V or less
(0)
1.8mA
1.2mA
Leakage current
Indicator light
PLC
24VDC
Grommet
Electrical entry
Relay, PLC
Application
AC
24V DC
or less
Load voltage
Maximum load voltage
50mA
100V DC
40mA
No
20mA
Internal resistance
Caution
Refer to "Magnetic Field Resistant Reed
Switches/Specific Product Precautions"
(pages 31 and 32).
AC
AC
48V DC
Operating time
1.2ms
Lead wire
Oil resistant, fire resistant heavy duty cord, 6.8, 0.75mm, 2 wire (Brown, Blue [White, Black]), 0.5m
Impact resistance
300m/s
Insulation resistance
50M or more at 500VAC (between lead wire and case)
Ambient temperature 10 to 60C
Enclosure
IEC standard IP67, watertight (JISCO920), oil proof construction
Indicate "L" for 3m lead wire and "Z" for 5m lead wire at the end of an auto switch part number.
Surge absorber
Reed switch
6.8
Diode
Blue
[Black]
Surge absorber
Choke
coil
Resistor
LED
Zener diode
Blue
()
[Black]
Brown
(+)
[White]
D-P75
2 x 2-6
Depth of counter bore 2.4
2-3.4 through
32
22
13.6
Brown
[White]
D-P74
Resistor
D-P70
20
Choke LED
coil
Reed switch
Resistor
LED
Diode bridge
Blue
[Black]
Brown
[White]
D-P80
Cylinder series
Reed switch
Brown
[White]
Blue
[Black]
CLK1P
40
7
50
8
63
8
Operating range:
The range within which the switch turns ON.
21
6-15-36
D-F7NJL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
Improved heat resistant type
Relay, PLC
25 mA or less
Load voltage
CQM
28 VDC or less
Load current
40 mA
CQ2
0.8 V or less
100 A at 24 VDC
RQ
MU
Leakage current
Indicator light
CQS
Current consumption
Precautions
CU
NPN
Applicable load
Caution
CUJ
3-wire
Ambient temperature
D-
Impact resistance
-X
Lead wire Between sensor and amplifier: Oil resistant vinyl heavy-duty cord, 3.4, 3 m
Grommet on amplifier: Oil resistant vinyl heavy-duty cord, 3.4, 0.2 mm2, 3 cores
(Brown, Black, Blue), 3 m
Weight
(g)
Auto switch model
Amplifier section
DC (+)
Brown lead wire
Sensor section
OUT
Black lead wire
Main
Main circuit
of switch
D-F7NJ
0.5
170
210
Dimensions
Indicator light
MODE POSITION
21.6
(4)
SMC
HEAT PROOF
AUTO SWITCH
AMPLIFIRE
3.8
22
MAX. 60C
(64.5)
0.7
OUT ()
Blue lead wire
15
MAX. 150C
3.4
6.2
MADE IN JAPAN
11
24 VDC
BLUE
GND
CAUTION
Load
MAX.
40 mA
BROWN
Vcc
BLACK
OUT
Switch
Main Circuit
D-F7NJ
Red
BROWN (+) 24 VDC
BLACK (OUT) NPN 24 V 40 mA
BLUE (-) GND
Green
40
Indication
Red
3.4
Operating range
Most sensitive
position
8.5
7-9-35
20Data
6-15-36
D-G5NBL
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
Grommet
CJ1
D-G5NBL
3-wire
Wiring type
CJP
NPN
Output type
Relay, PLC
Applicable load
CJ2
12 mA or less
Current consumption
Load voltage
10 to 28 VDC or less
Load current
40 mA or less
0.4 V or less
CM2
CG1
MB
100 A at 24 VDC
Leakage current
Indicator light
MB1
Lead wire Oil resistant vinyl heavy-duty cord, 4, 0.3 mm2, 3 cores (Brown, Black, Blue), 3 m
Note 1) Regarding the common specifications of the solid state switches, refer to page 6-16-7.
Note 2) Regarding the lead wire length, refer to page 6-16-7.
CA2
CS1
Weight
(g)
D-G5NB
C85
79
125
C76
C95
CP95
NCA
D-G5NB
33
11.2
D-
SMC
12
14
OUT
Black
OUT ()
Blue
-X
20-
Indicator light
Data
4.5 mounting hole
14.3
6.5
9.5
Main circuit
of switch
DC (+)
Brown
NCM
Dimensions
(16)
6-16-59
How to Order
Connector Specifications
D M9N S A PC
Connector model
M83 pin
M84 pin
M124 pin
2
2
Pin arrangement
Cable length
S
M
L
0.5 m
1.0 m
3.0 m
Connector model
A
B
D
M83 pin
M84 pin
M124 pin
Conformed standard
Impact resistance
300 m/s2
Enclosure
Insulation resistance
Withstand voltage 1500 VAC 1 minute (between contacts), Leak current 1 mA or less
Electrical
entry
Applicable model
Grommet (In-line)
Grommet
(Perpendicular)
Grommet (In-line)
Grommet
(Perpendicular)
F7NWV, F7BWV
F79F
F7BA
With timer
Magnetic field
Mounting
Function
Mounting
Function
Electrical
entry
Applicable model
Grommet
(In-line)
Grommet
(Perpendicular)
Grommet (In-line)
Grommet
(Perpendicular)
F7NT
Grommet
(In-line)
P5DW
Grommet
(Perpendicular)
Grommet (In-line)
Grommet
(Perpendicular)
Water resistant
Y7BA, F9BA
With timer
Grommet
(In-line)
M5NT, M5PT
H7NF, G59F
H7BA, G5BA
Grommet
(In-line)
With timer
G5NT
Grommet
(Perpendicular)
S99V1/2, T99V1/2
Wide detection
G5NB
2-color
indication
Rail
mounting
With diagnostic
style
Water resistant
2-color
indication
Band
mounting Diagnostic output
style
Water resistant
2-color indication
Tie-rod
mounting Diagnostic output
style
Water resistant
With timer
6-16-60
Grommet
(In-line)
F59F
F5BA
F5NT
Direct
mounting
style
Rotary
actuator
2-color
indication
DC 2-wire type
1 pin
2 pin
3 pin
4 pin
1 pin
2 pin
3 pin
4 pin
Brown
Blue
OUT (+)
OUT ()
OUT ()
OUT ( )
DC ()
OUT
DC ()
OUT
Brown
Blue
DC 3-wire type
Brown
Blue
Black
DC (+)
DC 4-wire type
Brown
Orange
Blue
Black
Diagnostic
DC (+)
output
Sensor type
CJ1
Connector Specifications
M83 pin
Connector model
M84 pin
M124 pin
CJ2
M83 pin
Pin arrangement
4
3
Conformed standard
Impact resistance
300 m/s2
Enclosure
CJP
CM2
CG1
MB
Insulation resistance
MB1
Withstand voltage 1500 VAC 1 minute (between contacts), Leak current 1 mA or less
CA2
CS1
M84 pin
Dimensions
C76
Connector model
C85
C95
10
Sensor section
M83 pin
4 pin
CP95
31.4
NCM
NCA
14
DM124 pin
Sensor section
M124 pin
44
-X
20Data
Number of pins
3
M8
Corrence Corporation
M12
Manufacturer
OMROM Corporation
XS3
Corrence Corporation
VA-4D
OMROM Corporation
XS2
PA5-4I
HR24
DKK Ltd.
CM01-8DP4S
6-16-61
-50
50
Dimensions and specifications are common as standard products with the exception of no indicator light.
Symbol
-61
This is the product which uses a heavy-duty cord having flexible characteristics 5 times (SMC
comparison) as strong as oil resistant heavy-duty cord used in the standard products.
61
6-16-62
Technical Data 1:
Plug-in Connector Assembly/
How to Use DIN Terminal
Plug-in Connector Assembly
D-A73C/A80C, D-J79C
D-C73C/C80C, D-H7C
Locking ring
Sleeve
How to connect
Connector
AC:
Connect to terminal no. 1 and no. 2
DC:
Connect (+) to no. 1 terminal and () to no. 2 terminal.
CJ1
CJP
CJ2
CM2
CG1
MB
MB1
Fixing screw
Tightening gland
With the convex port of the connector, insert the connector into the auto
switch into the sleeve. Screw the locking ring onto the switch.
(Do not tighten with pliers.)
CA2
CS1
Gland washer
C76
Gland gasket
C85
Terminal cover
Terminal block
C95
Terminal thread
CP95
Terminal gasket
NCM
NCA
How to change position of electrical entry
After separating the terminal block from the terminal cover, change the
position of the terminal cover to any desired direction (4 directions at every
90) to change the position of electrical entry.
D-X
Caution
When plugging a connector in the pin plug or pulling it out, hold a connector
perpendicularly as much as possible, not to slant it.
20-
Data
6-16-63
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Band Mounting Style
Caution
1. Tighten the screw under the specified torque when mounting auto switch.
2. Set the mounting band perpendicularly to cylinder tube.
Mounting correctly
Mounting incorrectly
Auto switch
Auto switch
Auto switch
Auto switch mounting
screw
M4 x 0.7 x 22 l
1. Put a mounting band on the cylinder tube and set it at the auto switch
mounting the mounting hole to the hole of stationary fitting.
2. Put the mounting section of the auto switch between the band mounting holes,
then adjust the position of mounting holes of switch to those of mounting band.
3. Lightly thread the auto switch mounting screw through the mounting hole into
the thread part of band fitting.
4. After reconfirming the detecting position, tighten the mounting screw to secure
the auto switch. (The tightening torque of M4 screw should be about 1 to 1.2
Nm.)
5. Modification of the detection position should be made in the condition of 3.
CDM2, CDBM2
CDVM3/5, CDLM2
CDG1, MGG
MGC
CDLG1
CDV3, CNA
CDVS, CDL1, CE2
RHC, MLGC, REC
BA
-02
BA
-32
BA01
BA02
BA32
BA
-04
50
63
80
100
BA
-05
BA
-05
BA
BA
BA
-06 -08 -10
6-16-64
CDJ2
CDVJ3/5
CDLJ2
CDM2, CDBM2
CDVM3/5, CDLM2
CDG1, MGG
CDLG1
MGC
RHC, MLGC, REC
RSDG
BJ2
-010
15
10
16
BJ2
-016
20
25
32
40
50
63
BMA2-050 BMA2-063
BMA2
BMA2-050
-040
BMA2-050
[Mounting screws set made of stainless steel]
The following set of mounting screws made of stainless steel is also available.
Use it in accordance with the operating environment.
(Please order the mounting band separately, since it is not included.)
BBA4: For D-C7/C8/H7
D-H7BAL switch is set on the cylinder with the stainless steel screws above
when shipped.
When only a switch is shipped independently, BBA4 screws are attached.
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Tie-rod Mounting Style
<Applicable auto switch>
Reed switch D-A33, D-A34, D-A44
Solid state switchD-G39, D-K39
CJ1
CJP
CJ2
CM2
Auto switch
Auto switch
mounting screw
M5 x 0.8 x 8 l
CG1
MB
MB1
Auto switch
Fook
Mounting band
CA2
CS1
C76
D-A4
C85
Auto switch
C95
CP95
Fook
Mounting band
1. Loosen the auto switch mounting screws at both sides to pull down
the hook.
2. Put a mounting band on the cylinder tube and set it at the auto
switch mounting position, and then hook the band.
3. Screw lightly the auto switch mounting screw.
4. Set the whole body to the detecting position by sliding, tighten the
mounting screw to secure the auto switch. (The tightening torque
should be about 2 to 3 Nm.)
5. Modification of the detecting position should be made in the
condition of 3.
CDM2, CDBM2
CDLM2
20
BM3-020
BM3-032
40
BM3-040
20
CDV3, CDVS
CE2, CNA
CDL1
CDS1
25
32
40
BD1
-04M
BD1
-05M
BD1
-06M
BD1
-08M
BD1
-10M
BD1
-02
BD1
-04M
RHC
BD1
-01M
BD1
-02M
MDB
BS1
-125
BS1
-140
BS1
-160
BS1
-180
BS1
-200
NCA
D-X
20Data
NCM
6-16-65
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Rail Mounting Style
<Applicable auto switch>
Reed switch D-A72, D-A73, D-A80, D-A72H, D-A73H, D-A76H, D-A80H, D-A73C, D-A80C, D-A79W
Solid state switchD-F79, D-F7P, D-J79, D-F7NV, D-F7PV, D-F7BV, D-J79C, D-F79W, D-F7PW, D-J79W,
D-F7NWV, D-F7BWV, D-F79F, D-F7BAL, D-F7BAVL, D-F7NTL
How to Mount and Move the Auto Switch
Auto switch mounting screw
(M3 x 0.5 x 8 l)
Auto switch
Auto switch
mounting nut
Auto switch spacer
Auto switch
mounting nut
1. Slide the auto switch mounting nut inserted into the mounting rail and
set it at the auto switch mounting position.
2. Fit the convex part of auto switch mounting arm into the concave part
of auto switch mounting rail. Then slide the switch over the nut.
(Series CDQ2: Fit the convex part of auto switch mounting arm
through the auto switch spacer into the concave part of auto switch
mounting rail.)
3. Push the auto switch mounting screw lightly into the mounting nut
through the hole of auto switch mounting arm.
4. After reconfirming the detecting position, tighten the mounting screw
to secure the auto switch. (Tightening torque of M3 screw should be
0.5 to 0.7 Nm.)
5. Modification of the detecting position should be made in the
condition of 3.
Auto Switch Mounting Bracket Part No. (Including nut, screw, (spacer))
Cylinder series
CDQ2
MDU
RSDQ
MK, MK2
CE1
CXT
BQ-1
16
BQ-1
20
BQ-1
BQ-1
40
32
50
25
63
BQ-2
BQ-2
BQ-2
BQ-1
BQ-2
BMU1-025 BMU1-025 BMU1-025 BMU1-025 BMU1-025
BQ-1
BQ-2
BQ-2
BQ-2
BQ-2
80
BQ-2
100
BQ-2
125
BQ-2
140
BQ-2
6-16-66
160
BQ-2
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Rail Mounting Style
<Applicable auto switch>
Solid state switchD-P5DWL
How to Mount and Move the Auto Switch
CJ1
CJP
CJ2
CM2
Spring washer
Switch
mounting
bracket
CG1
Magnetic field
resistant
auto switch
MB
MB1
Switch
mounting nut
CA2
Hexagon wrench key 2.5
Auto switch
CS1
C76
C85
1. Insert the hexagon socket head cap screw (M2.5 x 0.45 x 8 l) down lightly
to the M2.5 tapped portion of the lower part of switch mounting bracket's
concave part. (2 locations) Use caution to avoid the tip of a screw from
sticking out of the switch mounting bracket's bottom surface.
2. Install a spring washer in the hexagon socket head cap bolt (M3 x 0.5 x
16 l), then put it through the part of through-holes (2 locations) of an auto
switch.
3. As for switch mounting bracket, slightly thread the hexagon socket head
cap screw w into M3 tapped portion. (2 locations)
4. Fit the switch mounting bracket into the switch mounting groove on the
cylinder body, and then slide it to the detection position roughly.
5. After reconfirming the detecting position, tighten the mounting screw to
secure the auto switch.
C95
CP95
NCM
NCA
D-X
CDQ2
MK, MK2
MGP, MLGP
20-
Caution
Auto Switch Mounting Tool
When tightening hexagon socket head cap screw of an auto switch, use a
hexagon wrench key 2 and 2.5, depending on the case.
Tightening Torque
As a guide, set approximately 0.3 to 0.5 Nm for M2.5, 0.5 to 0.7 Nm for
M3 respectively.
6-16-67
Data
1. From the cutoff part of the rail on the cylinder body, insert the switch
mounting nuts (2 pcs.) into the rail groove.
2. Slide the switch mounting nuts (2 pcs.) and set into the auto switch
mounting position roughly. (25 mm or more should be left for the distance
between 2 nuts.)
3. Insert the convex portion of the switch mounting bracket into the concave
portion of a rail groove. Through-hole for the switch mounting bracket
should be placed on the switch mounting nut.
4. Put a flat washer (8 x 3.3) through a hexagon socket head screw (with
spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch
mounting bracket, then turning it lightly down to a mounting nut of switch.
(2 locations)
5. Put a round head Phillips screw (with spring washer, M3 x 0.5 x 14 l)
through the auto switch's through-hole (2 locations), and then push it
down into the M3 tapped part on the switch mounting bracket while
turning it lightly.
6. After reconfirming the detecting position, tighten the mounting screw to
secure the mounting bracket and the auto switch. (Tightening torque of
M3 screw should be 0.5 to 0.7 Nm.)
MDU
6-16-68
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Tie-rod Mounting Style
<Applicable auto switch>
Reed switchD-A53, D-A54, D-A56, D-A64
D-A67, D-A59W
Solid state switchD-F59, D-F5P
D-J59, D-J51, D-F5BAL
D-F59W, D-F5PW, D-J59W
D-F59F, D-F5NTL
CJ1
CJP
CJ2
CM2
Auto switch
Bracket set screw
(With hexagon socket head)
CG1
M5 x 0.8 x 12 l
MB
MB1
CA2
Auto switch
Auto switch mounting bracket
CS1
C76
Mounting
bracket (b)
Tie-rod
C85
C95
CP95
Auto switch
NCM
NCA
D-
1. Fix the auto switch on the auto switch mounting bracket with the
mounting screw (M4) and install the set screw.
2. Fit the mounting bracket into the cylinder tie-rod and then fix the auto
switch at the detecting position with the hexagonal wrench. (Be sure
to put the auto switch on the surface of cylinder tube.)
3. When changing the detecting position, loosen the set screw to move
the auto switch and then re-fix the auto switch on the cylinder tube.
(Tightening torque of M4 screw should be 1 to 1.2 Nm.)
-X
20Data
32
40
50
Mounting
bracket (b)
CDV3, CDVS
BT BT BT BT BT
CE2, CNA
-04 -04 -06 -08 -08
BT BT BT
CDL1
BT
BT
1. Fix the mounting bracket (A) on the auto switch with the set screw.
2. Fit the concave part of mounting bracket into tie-rod and set the auto
switch at the mounting position.
3. Insert the mounting bracket (B) from the underneath and put lightly in
the tie-rod with the mounting screw.
4. Set the whole body to the detecting position by sliding, tighten the
mounting screw to secure the auto switch. (Tightening torque of M5
screw should be 2 to 3 Nm.)
5. Modification of the detecting position should be made in the
condition of 3.
40
BA3
-040
BA3
-063
BA3
-080
BA3
-100
6-16-69
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Tie-rod Mounting Style
<Applicable auto switch>
Reed switch D-Z73/Z76/Z80
Solid state switch D-Y59 AB /Y69 AB , D-Y7P(V)
D-Y7NW(V)/Y7PW(V)/Y7BW(V)
D-Y7BAL
How to Mount and Move the Auto Switch
Auto switch
Tie-rod
Auto switch
Auto switch
mounting screw
Switch mounting bracket
CDL1, CDNA
6-16-70
Mounting
BMB4-032
BMB4-050
BA4-063
BA4-040
BA4-063
BA4-080
BS4-125
BS4-160
BS4-180
BS4-200
Accessory
Hexagon
socket head
set screw
(M4 x 0.7 x 6 l)
Quantity: 2
Auto switch
Tie-rod
Round head Phillips screw
With spring washer, M3 x 0.5 x 14 l
1. (For MDB)
Slightly screw the hexagon socket head cap screw (M4 x 0.7 x 8 l) into
the M4 tapped portion of switch mounting bracket. (2 locations) Use
caution that the tip of the hexagon socket head cap screw should not
stick out to the concave portion of switch mounting bracket.
2. (For MDB)
Put a round head Phillips screw (M3 x 0.5 x 14 l) through the auto
switch's through-hole (2 locations), and then push it down into the M3
tapped part on the switch mounting bracket while turning it lightly.
3. Place the concave part of the switch mounting bracket into the cylinder
tie-rod, and slide the switch mounting bracket in order to set roughly to
the detecting position.
4. After reconfirming the detecting position, tighten the M3 mounting screw
to secure the auto switch by making the bottom face of auto switch
attached to the cylinder tube. (Tightening torque of M3 screw should be
0.5 to 0.7 Nm.)
5. Tighten up M4 screw of switch mounting bracket to secure the switch
mounting bracket. (Ensure that tightening torque of M4 screw should be
set 1.0 to 1.2 Nm.)
Hexagon
socket head
set screw
(M4 x 0.7 x 8 l)
Quantity: 2
CDNA,
CDL1, (40 to 100)
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Tie-rod Mounting Style
<Applicable auto switch>
Reed switchD-90/97, D-90A/93A
CJ1
CJP
CJ2
Auto switch
CM2
Auto switch mounting bracket
CG1
Set screw
MB1
Set screw
Auto switch
MB
CA2
1. Insert the auto switch mounting nut into the auto switch mounting
groove and then set the switch at the mounting position by sliding.
2. Put the convex part of auto switch into the mounting groove and
slide it over the nut.
3. Push the auto switch mounting screw lightly into the mounting nut
through the mounting hole.
4. After reconfirming the detecting position, tighten the mounting screw
to secure the auto switch. (Tightening torque of M2.5 screw should
be 0.1 to 0.2 Nm.)
CS1
C76
C85
C95
Auto Switch Mounting Bracket Part No. (Including nut, screw) CP95
Cylinder
series
M2.5 x 12l
ML1
M2.5 x 10l
NCM
NCA
Data
Note) When tightening an auto
switch mounting screw, use a
watchmakers screwdriver with a
grip diameter of 5 to 6 mm. Also,
set the tightening torque to be
0.05 to 0.1 Nm. As a guide, turn
90 from the position where it
comes to feel tight.
1. Insert the auto switch into the mounting groove and set it at the auto
switch mounting position.
2. After reconfirming the detecting position, tighten the mounting screw
to secure the auto switch.
3. Modification of the detecting position should be made in the
condition of 1.
6-16-71
Technical Data 2:
How to Mount and Move the Auto Switch
Mounting Bracket Direct Mounting Style
<Applicable auto switch>
Reed switch D-Z73/Z76/Z80
Solid state switchD-Y59 AB /Y69AB , D-Y7P(V)
D-Y7NW(V)/Y7PW(V)/Y7BW(V)
D-Y7BAL
How to Mount and Move the Auto Switch
Flat head watchmakers screwdriver
Switch mounting screw (M2.5 x 4 l )
Accessory
5
to
6
Switch spacer
Correct
Incorrect
MDB1
6-16-72
40
50
63
BMP1-032
80
100
Series D-P3DW
Mounting and Moving Method of Auto Switch
Direct Mounting to the Round Groove
Applicable cylinder/actuator
CDQS
25 (0.98)
CDQ2 32 to 100 (1.26 to 3.94)
Compact cylinder with lock CDLQ 25 to 100 (0.98 to 3.94) BQ3-032S
Pin clamp cylinder
CKQG
50 (1.97)
Pin clamp cylinder with lock CLKQG
50 (1.97)
Compact cylinder
Applicable cylinder/actuator
Auto switch
mounting bracket
part no.
Convex part
BQ3-032S Note)
Convex part
Series D-P3DW
Applicable cylinder/actuator
Clamp cylinder
Clamp cylinder with lock
Air cylinder
Air cylinder with lock
Applicable cylinder/actuator
40 to 63 (1.58 to 2.48)
40 to 63 (1.58 to 2.48)
32 to 63 (1.26 to 2.48)
40, 50 (1.58, 1.97)
32 to 63 (1.26 to 2.48)
40, 50 (1.58, 1.97)
CKG1
CLK2G
MDB
CDA2
MDNB
CDNA
Air cylinder
Air cylinder with lock
MDB
CDA2
MDNB
CDNA
Convex part
Auto switch
Auto switch mounting bracket
Convex part
BMB8-0S Note)
Hexagon socket
head cap screw
(M2.5 x 6 L)
Tie-rod
Bore size
40 (1.58)
CKG1
CLK2G
50 (1.97)
63 (2.48)
CDA2
CDNA
Bore size
BA7T-063S
Bore size
Series
BMB8-050S
100 (3.94)
BA7T-080S
32
40
50
63
80 100
(1.26) (1.58) (1.97) (2.48) (3.15) (3.94)
MDB
BMB8-032S
MDNB (1.26 to 3.94)
BMB8-050S
BA7T-063S
125
(4.92)
BA7T-080S