Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
STANDARD FEATURES
SPECIFICATION
OPTIONS
Bodies
Cast Iron, Stainless Steel or Aluminium precision bored.
End Covers
Cast Iron, Stainless Steel or Aluminium spigot located in body for concentricity.
Body Vents
Vent Boxes
Dropout Boxes
Rotor
Fabricated Mild or Stainless Steel.
V.S. Drives
Bearings
Sealed-for -life-ball type rigged outboard or high temperature above 250 C.
Flameproof Motors
Speed Switches
Shear Plate Deflectors
Shaft Seal
Gland type with PTFE packing.
Drive
TEFC geared motor unit side wall mounted to valve body and complete with taper lock sprockets
chain drive all in an enclosed guard.
Air Purge
Gland
Body Vent
PLANNING-IN DETAIL
FOR GENERAL GUIDANCE ONLY
(TO COVER SAFETY ASPECTS
ASK FOR OUR SAFETY LEAFLETS)
12
406 220
195
28
143
14
12
406 234
195
28
143
12
12
70
70
15
406 259
219
28
143
12
12
90
90 250
15
478 290
249
35
155
12
18
10
108
108
19
478 320
279
35
195
12
18
10
128
128
19
512 329
289
35
220
12
12
10
140
140
20
626 403
352
50
235
12
18
14
165
165 1
20
322 630
357 450
626 428
377
50
285
12
18
14
187
187
20
700 453
402
50
289
16
18
14
148
148
20
700 503
452
50
335
16
18
14
173
173
500 1000 60
503 643
910 605
522
70
450
24
18
20
12
149
149
605 748
1000 707
625
70
540
24
22
20
12
175
175
VALVE SIZE
SIZE
A1
85
ON APPLICATION
H.P.
PLANNING-IN DETAIL
FOR GENERAL GUIDANCE ONLY
(TO COVER SAFETY ASPECTS
ASK FOR OUR SAFETY LEAFLETS)
VALVE SIZE
50 51
152
10
60
120
74
85 85
190
10
80
160
117
S H.P.
*DETAILS ON APPLICATION *
SIZE A
*DETAILS ON APPLICATION *
108 214
178
28
143
18
200
140 270
194
28
143
22
241
160 310
219
28
143
18
280
200 380
248
35
155
18
320
10
240 465
279
35
195
12
22
395
10
270 520
289
35
220
12
22
445
10
300 580
352
50
235
12
22
495
14
320 625
80
377
50
285
16
32
578
14
340 670
402
50
289
20
32
635
14
385 760
452
50
335
20
35
749
14
500 1000
45
522
70
450
28
35
914
20
12
All dimensions in mm
Closed rotor
Suitable for general use on filters, cyclones, silos,
screw conveyors and on low pressure conveying
systems. Sealing by means of packing gland.
Scalloped rotor
Particularly suitable for sticky materials and discharge
can be further aided by the application of PTFE coating,
generally used in food processes where no product buildup can be tolerated. Pressures to 15 psi are applicable.
VALVE SELECTION
The chart below gives theoretical and estimated
throughputs on the basis of rotor speed.
The theoretical figure is determined by the swept
volume of the valve and is calculated on a pocket
fillage of 100%.
In practice this is seldom achieved as density,
product characteristics, pressure differential,
feeding methods, all affect the valve throughput
efficiency.
On these considerations the estimated figures
are assessed and are more acceptable for
selecting the correct valve. e.g. Select a valve
to handle 7 tons/hour of flour at 35 lb/cu. ft.
Volume required = 7.0 x 2000 35 = 400 cu.
ft/hr.
450
400
350
300
200
250
150
125
85
50
1158
1158
681
681
356
356
205
205
149
149
104
104
65.2
65.2
45.4
45.4
25.6
25.6
12.7
12.7
5.0
5.0
2.8
2.8
.96
.96
.228
.228
5792
5792
3405
3405
1780
1780
1024
1024
743
743
519
519
326
326
227
227
128
128
63
63
25
25
14
14
4.8
4.8
1.1
1.1
10
12 14 16 18 20
Rotor Speed RPM
22
27799
19737
16343
11604
8544
6066
4916
3490
3568
2533
2490
1768
1564
1110
1090
774
615
437
304
216
121
86
68
48
23
16.3
5.5
3.9
30116
20479
17704
12039
9255
6293
5326
3622
3866
2629
2697
1834
1694
1152
1181
803
666
453
329
224
131
89
73
50
25
17
5.9
4
24
26
100%
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
Practical
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
100%
Practical
NOTES
Throughput
Certain products when fluidised can greatly
exceed the conservative rating and on
application, e.g. cement, 100% pocket
fillage has been known to occur - similarly
light products up to 15lb/cu. ft. the
opposite effect can happen.
Temperature
Note: On any application above
ambient (21C) it is important to
specify operating temperatures so
rotor compensation for expansion can
be adjusted as necessary.
Conversions
Divide cubic metres/hr by 0.0283 to
obtain cubic feet/hr.
Theoretical capacity 100% pocket
fillage efficiency.
Conservative estimated throughout.
Rotolok Ltd
1 Millennium Place, Tiverton Business Park,
Tiverton, Devon EX16 6SB
Tel: 01884 232232 Fax: 01884 232200
e-mail: sales@rotolok.co.uk
website: www.rotolok.co.uk