Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Article ID: 175278 - Last Review: September 14, 2007 - Revision: 4.6 Bu içerik dışında,
bir kişinin
How to add additional non-hot swap SCSI hard disks to a cluster node on a yardımına
ihtiyacınız var mı?
shared SCSI bus
Destek uzmanı ile e-
View products that this article applies to. posta, çevrimiçi veya
telefonla görüş.
This article was previously published under Q175278
Article Translations
Expand all | Collapse all
Arabic
Arabic
SUMMARY
This article discusses how to add additional non-hot swap small computer system interface (SCSI) hard
Search related
disks to a cluster node, on a shared SCSI bus. Follow the guidelines discussed in this article if your topics
computer does not support the hot swapping of SCSI hard disks.
Hard drive cluster size
Back to the top
Turn off hard disk
To add additional SCSI hard disks to an existing cluster, use the appropriate method for your version of Windows 2000
Microsoft Windows. Sayfa Araçları
Bu sayfayı yazdır
1. Change the startup values for the Cluster Disk device (for Windows NT 4.0 Server) or Clusdisk
device (for Windows 2000 Server or for Windows Server 2003) and the Cluster service to Bu sayfayı e-posta ile
yolla
Disabled. To do so, follow these steps:
a. For Windows NT 4.0 Server:
1. Click Start, point to Settings, and then click Control Panel.
2. Double-click Devices.
3. In the list of devices, click Cluster Disk, and then click Startup.
4. Click Disabled, click OK, and then click Close.
5. Close the Devices window.
6. In Control Panel, double-click Services.
7. In the list of services, click Cluster Server, and then click Startup.
8. Change the setting to Disabled, click OK, and then click Close.
9. Close the Services window, and then close Control Panel.
b. For Windows 2000 Server and Windows Server 2003:
a. Right-click My Computer, and then click Manage.
b. In the left pane, click Device Manager.
c. On the View menu, click Show hidden devices.
d. In the right pane, expand Non-Plug and Play Drivers, and then double-click
Clusdisk.
e. On the Driver tab, in the Type box, click Disabled, and then click OK.
f. In the left pane, expand Services and Applications, and then click Services.
g. In the right pane, double-click the Cluster Server service.
h. In the Startup type box, click Disabled, and then click OK.
i. Close the Computer Management tool.
2. Shut down both of the cluster nodes and turn off both of the computers.
3. Turn off all the SCSI devices on the shared SCSI bus.
4. Add or replace the hard disks on the shared SCSI bus.
Note Make sure that every device on the shared SCSI bus has a unique SCSI ID. SCSI host
adapters each use a SCSI ID (typically 6 and 7). Also, make sure that the SCSI bus is terminated
correctly.
For additional information about connecting SCSI devices or about SCSI termination, click the
following article numbers to view the articles in the Microsoft Knowledge Base:
101352 Properly connecting SCSI devices to Windows NT
5. Start node 1 of the cluster and let Windows to completely start on the node.
6. Turn on node 2 of the cluster, but do not let Windows start on the second node. To stop Windows
from loading:
a. For Windows NT 4.0 Server, at the OS Loader menu, press SPACEBAR to pause the
startup. When you pause the startup, you prevent Windows NT from loading.
b. For Windows 2000 Server, when the computer first starts and you see the For
troubleshooting and advanced startup options for Windows 2000, press F8
http://support.microsoft.com/kb/175278[16.07.2009 17:02:58]
How to add additional non-hot swap SCSI hard disks to a cluster node on a shared SCSI bus
7. On the Tools menu, click Properties, and then in the Label box, type a volume
label that matches the corresponding drive letter.
Note If you connect to a new drive, the Write Signature and Upgrade Disk Wizard
starts automatically. Click Next to go through the wizard. The wizard sets the disk
to dynamic. To reset the disk to Basic, right-click Disk n, where n specifies the
disk you are working with, and then click Revert To Basic Disk. Make sure that
the disk is set to Basic before you partition the hard disk in step 3.
For additional information about dynamic and basic disks in a Cluster service
environment, click the following article number to view the article in the Microsoft
Knowledge Base:
237853 Dynamic disk configuration unavailable for server cluster disk
resources
3. Right-click the unallocated space on the new drive, and then click Create
Partition.
4. In the Create Partition Wizard, click Next, click the type of partition that you
want, click Next, type the size of the partition in megabytes (MB), and then click
Next.
5. Click the drive letter that you want to assign to the partition, and then click Next.
6. Under Formatting, make sure that the File system to use drop-down list is set
to NTFS.
7. In the Volume label box, type a volume label that matches the corresponding
drive letter, click Next and then click Finish.
http://support.microsoft.com/kb/175278[16.07.2009 17:02:58]
How to add additional non-hot swap SCSI hard disks to a cluster node on a shared SCSI bus
except:
a. In Devices, change the Startup value for the Cluster Disk device (in Windows NT 4.0
Server) or Clusdisk device (in Windows 2000 Server or in Windows Server 2003) to
System.
b. In Services, change the Startup value for the Cluster Server service to Automatic.
13. Restart node 2 and let the computer completely restart.
14. Use the Cluster Administrator tool to create a physical disk resource for each new disk, and then
bring the disks online.
15. If there are errors, check the SCSI cabling, termination and SCSI ID assignment for correct
configuration. For additional information about cluster disk and drive connection issues, visit the
following Microsoft Web site:
http://technet.microsoft.com/en-us/library/cc757627.aspx
16. If there are no errors, let the operating system start on node 1. To do so, follow the steps as
appropriate for your operating system:
For Windows NT 4.0 Server, press SPACEBAR.
For Windows 2000 Server, use the arrow keys to select Boot Normally, and then press
ENTER.
For Windows Server 2003, use the arrow keys to select Start Windows Normally, press
ENTER, use the arrow keys to select the operating system, and then press ENTER.
17. When the node comes online and appears so in Cluster Administrator, try to move the group to
the node. To do so, right-click the group, and then select the option Move. The group and all of
its resources move to another node. Test to verify that you can go online on each node.
REFERENCES
For additional information about Microsoft Cluster service and how to add an additional SCSI hard disk,
see Chapter 4 of the Microsoft Cluster Server Administrator's Guide. To locate the guide, visit the
following Microsoft Web site:
http://www.microsoft.com/resources/documentation/windowsnt/4/server/proddocs/en-us/clustsvr/
mscsadm0.mspx
For additional information about how to replace a disk that is on a Windows 2000 or a Windows Server
2003 cluster, click the following article number to view the article in the Microsoft Knowledge Base:
305793 How to replace a disk that is on a Windows 2000 or a Windows Server 2003 cluster
APPLIES TO
Submit
http://support.microsoft.com/kb/175278[16.07.2009 17:02:58]
How to add additional non-hot swap SCSI hard disks to a cluster node on a shared SCSI bus
Hizmet Antlaşması
Yardım ve Destek Bizimle İrtibata Geçin | Kullanım Şartları | Tescilli markalar | Gizlilik Bildirisi ©2009 Microsoft
http://support.microsoft.com/kb/175278[16.07.2009 17:02:58]