Sei sulla pagina 1di 3

Take Assessment ROUTE Chapter 3 CCNP ROUTE:

1. Which OSPF network type requires the election of a DR/BDR?


BROADCAST

2. In an OSPF hub-and-spoke topology, what needs to be done to ensure that the
spoke routers would never be selected as DR and BDR?
All spoke routers need to be configured with an OSPF interface
priority of 0 (ip ospf priority) so that they will not become the
DR/BDR.

3. A network administrator is implementing OSPF in a portion of the network
and must ensure that only specific routes are advertised via OSPF. Which
network statement would configure the OSPF process for networks
192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now located in the
backbone area, and inject them into the OSPF domain?
r1(config-router)# network 192.168.4.0 0.0.3.255 area 0

4. What two advantages does authentication provide that should be considered
when planning an OSPF implementation? (Choose two.)
It prevents routing information from being falsified in transit.
It ensures that routing information comes from a valid source router.

5. When will a router in an OSPF nonbackbone area receive a default route from
the ABR or ASBR? (Choose three.)
when the area is a totally stubby area
when the area is a NSSA totally stubby area
when the area is a normal area and the ASBR has been configured with
the default-information originate always command
6. What are two reasons for creating an OSPF network with multiple areas?
(Choose two.)
to reduce SPF calculations
to reduce use of memory and processor resources

7. What does OSPF use to calculate the cost to a destination network?
BANDWIDTH

8. Which three items must match between OSPF neighbors in order to form an
adjacency? (Choose three.)
HELLO/DEAD INTERVAL
AREA ID
authentication type

9. Refer to the exhibit. When OSPF is operational and converged, what neighbor
relationship is developed between Router1 and Router2?
A FULL adjacency is formed.

10. A fully converged five router OSPF network has been running successfully for
several weeks. All configurations have been saved and no static routes are used.
If one router loses power and reboots, what information will be in its routing
table after the configuration file is loaded but before OSPF has converged?
Directly connected networks that are operational will be in the
routing table.

11. What are two effects of using multiple OSPF areas that reduce bandwidth and
router overhead? (Choose two.)
reduction in the size of the LSDB
limits on the propagation of type 1 and 2 LSAs

12. What is the function of the OSPF LSU packet?
to announce new OSPF information

13. Refer to the exhibit. How does the router treat the authentication of OSPF
packets that enter and leave FastEthernet interface 0/0?
Two copies of every OSPF packet are sent, one with key 10 and one
with key 20.

14. Refer to the exhibit. Which type of OSPF packets are represented by the debug
command output?
hello packets sent with a MD5 hashed authentication key id of 100

15. Refer to the exhibit. What destination address will RTB use to advertise LSAs?
224.0.0.6

16. Which two statements are correct about OSPF route summarization? (Choose
two.)
The metric of the summary route is equal to the lowest cost network
within the summary address range.
The area 51 range 172.0.0.0 255.0.0.0 command identifies area 51 as
the area that contains the range of networks to be summarized.

17. Which two statements are correct about OSPF NSSA areas? (Choose two.)
Type 7 LSAs are translated to type 5 LSAs by the ABR.
Type 7 LSAs are originated by the ASBR that is connected to the
NSSA.

18. How can correct OSPF topology change-behavior be verified as part of an
implementation plan?
Test link failure and router failure events.
19. What is the correct method to configure route summarization on an OSPF
router?
Configure OSPF and instruct the ABR to summarize specific area
routes.

20. Which command can be used to determine the stability of an OSPF area by
examining the number of times SPF has been executed for that area?
show ip ospf

Potrebbero piacerti anche