0 valutazioniIl 0% ha trovato utile questo documento (0 voti)
47 visualizzazioni14 pagine
Feature Deployment and Test Guide Internal Use Only ZTE CORPORATION. All rights reserved. Feature ID and name. 1 1. Test purpose. 1 1. Functional description. 1 1. Hardware requirement. 2 1.4. Software requirement. 3 1.4. Topo.
Feature Deployment and Test Guide Internal Use Only ZTE CORPORATION. All rights reserved. Feature ID and name. 1 1. Test purpose. 1 1. Functional description. 1 1. Hardware requirement. 2 1.4. Software requirement. 3 1.4. Topo.
Feature Deployment and Test Guide Internal Use Only ZTE CORPORATION. All rights reserved. Feature ID and name. 1 1. Test purpose. 1 1. Functional description. 1 1. Hardware requirement. 2 1.4. Software requirement. 3 1.4. Topo.
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. I
Feature Test Guide Version Date Author Approved By Remarks V1.00 2012-12-19 Jiao Meipeng Wang Juntao Not open to the Third Party
2014 ZTE Corporation. All rights reserved. ZTE CONFIDENTIAL: This document contains proprietary information of ZTE and is not to be disclosed or used without the prior written permission of ZTE. Due to update and improvement of ZTE products and technologies, information in this document is subjected to change without notice.
Feature Deployment & Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. II
TABLE OF CONTENTS 1. Feature Deployment & Test Guide ................................................................ 1 1.1 Feature ID and name ........................................................................................ 1 1.2 Test purpose..................................................................................................... 1 1.3 Functional description ....................................................................................... 1 1.4 Preparations ..................................................................................................... 2 1.4.1 License ............................................................................................................ 2 1.4.2 Hardware requirement ...................................................................................... 2 1.4.3 Software requirement ....................................................................................... 3 1.4.4 Topo ................................................................................................................. 3 1.5 Data configuration ............................................................................................ 4 1.5.1 SGSN/GGSN- ZTE .......................................................................................... 4 1.5.2 MSC/MGW ZTE ............................................................................................ 4 1.5.3 HLR ZTE ....................................................................................................... 4 1.5.4 RNC ................................................................................................................. 4 1.5.5 NodeB .............................................................................................................. 9 1.5.6 Hide parameter in RNC .................................................................................... 9 1.6 Steps for test .................................................................................................... 9 1.7 Expected results ............................................................................................. 10 1.8 Counter List .................................................................................................... 10 1.9 FAQs .............................................................................................................. 11
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 1
1. Feature Deployment & Test Guide 1.1 Feature ID and name ZWF21-01-003 Paging 1.2 Test purpose The purpose of this test case is to verify if the procedure of paging an Idle mode MS in CS domain is normal. Related documents: ZTE UMTS Connection Management Feature Guide 1.3 Functional description When there are service demands in CN, the system will trigger the UE to set up the connection between the UE and the CN through its paging function. For example, the UE needs to receive the Short Message Service (SMS) or Multimedia Message Service (MMS), or other user calls the UE. The CN sends paging message through the Iu interface to the RNC. The RNC selects an area according to the RRC connections status of the UE and sends paging message to the UE. When UE is in IDLE status RNC cannot obtain information in the specific location of UE. Therefore, RNC sends paging message within the LA or RA according to the LA/RA information carried in the paging message of CN. When UE is in PCH status ZTE RAN supports the URA_PCH/CELL_PCH status. And RAN knows the location information of UE in the URA and sends paging messages within the whole URA(for URA_PCH) or sends paging messages within the cell(for CELL_PCH). When UE is in FACH or DCH status RNC knows the location information of UE in the cell level and sends paging messages to the cell.
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 2
ZTE RAN allows RNC to initiate paging on the following special occasions: When there are data packets in the downlink buffer, RNC sends paging message to trigger the UE status change from URA_PCH/CELL_PCH to CELL_FACH and set up the service bearer for the downlink data transmission. After the system information changes, RNC sends the paging message to notify all UEs in Idle or PCH status of a cell. When it is necessary to suspend the RRC connection of a UE in the PCH status, RNC sends a paging message to release the RRC connection of UE. ZTE RAN supports two paging modes: PAGING TYPE 1 and PAGING TYPE 2: For the UE in the IDLE, URA_PCH/CELL_PCH, or CELL_PCH status, paging message of PAGING TYPE 1 is sent. For the UE in the CELL_FACH, or the CELL_DCH status, paging message of PAGING TYPE 2 is sent. Common transport channel PCH is used to transmit PAGING TYPE 1 messages. For avoiding block of voice calls during congestion of PCH caused by huge PAGING TYPE 1 messages, ZTE RAN supports prior transmission of CS paging message than that of PS paging message. 1.4 Preparations 1.4.1 License N/A 1.4.2 Hardware requirement NE Requirement Notes RNC V3 None RNC V4 None NodeB V3 None NodeB V4 None
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 3
1.4.3 Software requirement NE Version Requirement Notes UE UMTS FDD Number: 2 Category: Any Release : R99
1.4.4 Topo CN CS CN PS RNC 1 NodeB 1 Cell1 Cell2 Cell3 Logical line ATM over E1/T1 ATM over STM1/4 IP over STM1/4 IP over E1/T1 Any Transmission IP over Ethernet
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 4
1.5 Data configuration 1.5.1 SGSN/GGSN- ZTE N/A 1.5.2 MSC/MGW ZTE N/A 1.5.3 HLR ZTE In the RAB_AssignmentRequestMsg message, MSC indicates the traffic class and the MBR/GBR: TRANAP_Message.RAB_AssignmentRequestMsg.rAB_SetupOrModifyList.elem[0].rAB_SetupOr ModifyItemFirst.rAB_Parameters.trafficClass = eRANAP_TrafficClass_conversational TRANAP_Message.RAB_AssignmentRequestMsg.rAB_SetupOrModifyList.elem[0].rAB_SetupOr ModifyItemFirst.rAB_Parameters.maxBitrate.elem[0] = 12200 TRANAP_Message.RAB_AssignmentRequestMsg.rAB_SetupOrModifyList.elem[0].rAB_SetupOr ModifyItemFirst.rAB_Parameters.guaranteedBitRate.elem[0] = 12200. 1.5.4 RNC For saving power, the UE in the Idle or PCH state monitors the PICH channel in the Discontinuous Reception (DRX) mode. In the DRX mode, the UE monitors the page indicator (PI) once every DRX period. In the OMCR, you can configure three DRX cycle length coefficients: UTRAN DRX Cycle Length Coefficient. CS Domain DRX Cycle Length Coefficient and PS Domain DRX Cycle Length Coefficient. 1. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> UTRAN DRX Cycle Length Coefficient
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 5
---- UTRAN DRX Cycle Length Coefficient: 6: This parameter configures the UTRAN DRX Cycle Length Coefficient. 2. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> PLMN Relation Configuration->CN NAS System Information->CS Domain DRX Cycle Length Coefficient
---- CS Domain DRX Cycle Length Coefficient: 6: This parameter configures the CS Domain DRX Cycle Length Coefficient for paging procedure.
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 6
3. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> PLMN Relation Configuration->CN NAS System Information->PS Domain DRX Cycle Length Coefficient ---- PS Domain DRX Cycle Length Coefficient: 6 This parameter configures the PS Domain DRX Cycle Length Coefficient for paging procedure. 4. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> UTRAN Cell-> Sending Times of Paging Message
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 7
---- Sending Times of Paging Message: 3: This parameter configures the Sending Times of Paging Message for paging procedure. The UE judges whether the network is paging itself by monitoring its own PI. Each PICH frame can contain the PI of multiple UEs. The table shows the relations between the parameter the number of PIs included in a PICH frame and the transmit power. Number of PIs in each frame Number of repeated bits in the PICH Transmit power of the PICH in comparison with that of the CPICH 18 16 -7 36 8 -7 72 4 -5 144 2 -2 5. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> UTRAN Cell->Channel Configuration->SCCPCH Configuration->PICH Configuration->Number of Paging Indicators per PICH Frame
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 8
---- Number of Paging Indicators per PICH Frame: 18: This parameter configures the Number of Paging Indicators per PICH Frame for paging procedure. 6. Path: View->Configuration Management->RNC 78-> Modify Area->Management Element->UMTS Logical Function Configuration-> UTRAN Cell->PICH Power
---- PICH Power: -7 This parameter configures the PICH Power for paging procedure.
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 9
1.5.5 NodeB N/A. 1.5.6 Hide parameter in RNC This feature does not have the related hide parameters. Caution: The Hide parameter internal use only. Not open to the Third Party
1.6 Steps for test 1. UE1 camps on cell 1 in idle mode. UE2 makes a voice call to UE1. Capture the Iu interface signaling. The Paging message from CS CN to RNC is showed below: . The Paging message includes the CN domain indicator (CS), the permanent NAS UE identity (IMSI) or the temporary UE identity (TMSI), the paging area (LAC) and the paging cause. 2. RNC sends paging message on PCH channel in the paging area. 3. UE1 responses to this paging message. The voice call is established successfully. The procedure is general AMR speech. The signaling procedure can be found in document ZWF21-02-001 CS Conversational RAB for AMR Speech. 4. Release the AMR voice call.
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 10
1.7 Expected results The paging message is successfully sent by CN to RNC. Then RNC sends it on PCH channel in the paging area. After UE1 responses to this paging message, the AMR voice call is established successfully. Signaling:
ZWF21-01-003 Paging_IU interface.zip
ZWF21-01-003 Paging.zip
1.8 Counter List
C310555152 Total Number of Paging Type1 Request in Cell C310555153 Number of CN Originated Paging Type1 Request in Cell C310555154 Number of RNC Originated Paging Type1 Request in Cell C310555155 Number of Invalid Paging Type1 Request in Cell C310555156 Number of Paging Type1 Request Sending Failure in Cell C310555157 Number of RNC Attempt Paging Type1 C310555158 Number of Successful Sending Paging Type1 C310555159 Number of Congested Pagings for Paging Type1 C310555160 Number of Paging Response to Paging Type1 in Cell C310555161 Number of Paging Type2 Sending in Cell C310553540 Number of RNC Attempt High-PRI Paging Type1(Including RNC Re-transmission) in Cell C310553541 Number of Successful Sending High-PRI Paging Type1(Including RNC Re-transmission) C310553542 Number of Congested Pagings for High-PRI Paging Type1(Including RNC Re-Transmission)
Feature Test Guide Internal Use Only
ZTE Confidential Proprietary 2014 ZTE CORPORATION. All rights reserved. 11
C310554582 Number of FP fail Pagings for Paging Type1(Including RNC Re-Transmission) 1.9 FAQs None