Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
In addition to producing high quality radiographs, the radiographer must also be skilled in
radiographic interpretation. Interpretation of radiographs takes place in three basic steps: (1)
detection, (2) interpretation, and (3) ealuation. !ll of these steps make use of the radiographer"s
isual acuity. #isual acuity is the ability to resole a spatial pattern in an image. $he ability of an
indiidual to detect discontinuities in radiography is also affected by the lighting condition in the
place of ie%ing, and the e&perience leel for recogni'ing arious features in the image. $he
follo%ing material %as deeloped to help students deelop an understanding of the types of
defects found in %eldments and ho% they appear in a radiograph.
Discontinuities
(iscontinuities are interruptions in the typical structure of a material. $hese interruptions may
occur in the base metal, %eld material or )heat affected) 'ones. (iscontinuities, %hich do not
meet the requirements of the codes or specifications used to inoke and control an inspection, are
referred to as defects.
General Welding Discontinuities
$he follo%ing discontinuities are typical of all types of %elding.
Cold lap is a condition %here the %eld filler metal does not properly fuse %ith the base metal or
the preious %eld pass material (interpass cold lap). $he arc does not melt the base metal
sufficiently and causes the slightly molten puddle to flo% into the base material %ithout bonding.
Porosity is the result of gas entrapment in the solidifying metal. *orosity can take many shapes
on a radiograph but often appears as dark round or irregular spots or specks appearing singularly,
in clusters, or in ro%s. +ometimes, porosity is elongated and may appear to hae a tail. $his is
the result of gas attempting to escape %hile the metal is still in a liquid state and is called
%ormhole porosity. !ll porosity is a oid in the material and it %ill hae a higher radiographic
density than the surrounding area.
.
Cluster porosity is caused %hen flu& coated electrodes are contaminated %ith moisture. $he
moisture turns into a gas %hen heated and becomes trapped in the %eld during the %elding
process. ,luster porosity appear -ust like regular porosity in the radiograph but the indications
%ill be grouped close together.
Slag inclusions are nonmetallic solid material entrapped in %eld metal or bet%een %eld and base
metal. In a radiograph, dark, -agged asymmetrical shapes %ithin the %eld or along the %eld -oint
areas are indicatie of slag inclusions.
Incomplete penetration (IP) or lack of penetration (LOP) occurs %hen the %eld metal fails to
penetrate the -oint. It is one of the most ob-ectionable %eld discontinuities. .ack of penetration
allo%s a natural stress riser from %hich a crack may propagate. $he appearance on a radiograph
is a dark area %ith %ell/defined, straight edges that follo%s the land or root face do%n the center
of the %eldment.
Incomplete fusion is a condition %here the %eld filler metal does not properly fuse %ith the base
metal. !ppearance on radiograph: usually appears as a dark line or lines oriented in the direction
of the %eld seam along the %eld preparation or -oining area.
Internal concavity or suck ack is a condition %here the %eld metal has contracted as it cools
and has been dra%n up into the root of the %eld. 0n a radiograph it looks similar to a lack of
penetration but the line has irregular edges and it is often quite %ide in the center of the %eld
image.
Internal or root undercut is an erosion of the base metal ne&t to the root of the %eld. In the
radiographic image it appears as a dark irregular line offset from the centerline of the %eldment.
1ndercutting is not as straight edged as .0* because it does not follo% a ground edge.
!"ternal or cro#n undercut is an erosion of the base metal ne&t to the cro%n of the %eld. In
the radiograph, it appears as a dark irregular line along the outside edge of the %eld area.
Offset or mismatc$ are terms associated %ith a condition %here t%o pieces being %elded
together are not properly aligned. $he radiographic image sho%s a noticeable difference in
density bet%een the t%o pieces. $he difference in density is caused by the difference in material
thickness. $he dark, straight line is caused by the failure of the %eld metal to fuse %ith the land
area.
Inade%uate #eld reinforcement is an area of a %eld %here the thickness of %eld metal
deposited is less than the thickness of the base material. It is ery easy to determine by
radiograph if the %eld has inadequate reinforcement, because the image density in the area of
suspected inadequacy %ill be higher (darker) than the image density of the surrounding base
material.
!"cess #eld reinforcement is an area of a %eld that has %eld metal added in e&cess of that
specified by engineering dra%ings and codes. $he appearance on a radiograph is a locali'ed,
lighter area in the %eld. ! isual inspection %ill easily determine if the %eld reinforcement is in
e&cess of that specified by the engineering requirements.
Cracks can be detected in a radiograph only %hen they are propagating in a direction that
produces a change in thickness that is parallel to the &/ray beam. ,racks %ill appear as -agged
and often ery faint irregular lines. ,racks can sometimes appear as )tails) on inclusions or
porosity.
Discontinuities in &IG #elds
$he follo%ing discontinuities are unique to the $I2 %elding process. $hese discontinuities occur
in most metals %elded by the process, including aluminum and stainless steels. $he $I2 method
of %elding produces a clean homogeneous %eld %hich %hen radiographed is easily interpreted.
&ungsten inclusions' $ungsten is a brittle and inherently dense material used in the electrode in
tungsten inert gas %elding. If improper %elding procedures are used, tungsten may be entrapped
in the %eld. 3adiographically, tungsten is more dense than aluminum or steel, therefore it sho%s
up as a lighter area %ith a distinct outline on the radiograph.
O"ide inclusions are usually isible on the surface of material being %elded (especially
aluminum). 0&ide inclusions are less dense than the surrounding material and, therefore, appear
as dark irregularly shaped discontinuities in the radiograph.
Discontinuities in Gas (etal )rc Welds (G()W)
$he follo%ing discontinuities are most commonly found in 24!5 %elds.
W$iskers are short lengths of %eld electrode %ire, isible on the top or bottom surface of the
%eld or contained %ithin the %eld. 0n a radiograph they appear as light, )%ire like) indications.
*urn+&$roug$ results %hen too much heat causes e&cessie %eld metal to penetrate the %eld
'one. 0ften lumps of metal sag through the %eld, creating a thick globular condition on the back
of the %eld. $hese globs of metal are referred to as icicles. 0n a radiograph, burn/through
appears as dark spots, %hich are often surrounded by light globular areas (icicles).