130 Products identified with this symbol are stocked subject to prior sale in one or more of our global
bal locations. If unavailable from our facility nearest you, allow for shipping time from another facility. P u s h
t o
C l o s e
L a t c h e s V i s i b l e Southco
Push to Close Latches
Paddle Latch Series, Medium and Large Sizes Metal slide Pull paddle to open Locking and non-locking versions Latch is flush with outer panel Single-hole installation SERIES L W R B C D MIN. E REF. T MAX. MIN. MAX. 20 300 71.5 108 55.5 (2.19 .01) 82.5 +0.3 -0.1 2.5 (.09) 3 (.13) 8 (.31) 11 (.44) 11 (.44) 15.9 (.63) 7.9 (.31) 11.9 (.47) 11.1 (.44) 14.3 (.56) 14.3 (.56) 20.6 (.81) 6.4 (.25) 9.5 (.38) +0.1 -0.3 +0.2 -0.3 +0.3 -0.2 (2.81 .01) (4.25 .01) (3.25 .01) Installation Series 20 GAP IMPORTANT see instruction No. 3 Edge of frame or modified latching surface (notch, hole, bracket or shim). See in- struction No. 2. B E C D MIN. T MAX. LATCH ASSEMBLY ADJUSTING NUT MOUNTING BRACKET LOCKWASHER MOUNTING NUT SLIDE FRAME DOOR R MAX. W B L DOOR FRAME 8 ( . 31) 84 (3.31) 1.2 (.05) M5 Thread GAP IMPORTANT (See installation) 68.5 (2.69) 19 (.75) 36 (1.39) 17.5 (.69) 6.4 (.25) MAX. Door Thickness 7.9 (.31) FRAME DOOR LATCH MOUNTING BRACKET ADJUSTING NUT LOCKWASHER MOUNTING NUT Available with or without lock (see part number table). FINISH Brushed Zinc plated Stainless steel Steel 20 Series PART NUMBER Without Lock 20 Series PART NUMBER With Lock* 64-21-10 64-21-13 64-22-10 64-22-13 Black Silver Powder Coat 64-21-11 64-21-15 64-22-11 64-22-15 *Locks are keyed alike. Different key codes are available. Contact Southco for details. millimeter (inch) millimeter (inch) Dimensions without tolerances are for reference only. 131 Products identified with this symbol are stocked subject to prior sale in one or more of our global locations. If unavailable from our facility nearest you, allow for shipping time from another facility. P u s h
t o
C l o s e
L a t c h e s V i s i b l e 1. Prepare door. 2. If frame requires modification (notch, hole or shim), be sure to observe C and D dimensions and to allow sufficient width clearance for latching slide. See latch drawings for width of slide. 3. Measure your door thickness and set adjusting nut so that GAP is equal to door thickness within plus 0.8 (.03), minus 0.0 (.00). 4. Assemble latch in door and tighten mounting nut. GAP IMPORTANT (See installation) FRAME DOOR LATCH ASSEMBLY MOUNTING BRACKET ADJUSTING NUT LOCKWASHER MOUNTING NUT 127 (5) 28.5 (1.13) 101.5 (4) 11 (.44) Available with or without lock (see part number table). 11.9 (.47) 1.6 (.06) 4.5 (.17) 1/4-20 THREAD 49 (1.94) 25.5 (1.01) MAXIMUM DOOR THICKNESS = 9.5 (.375) Material and Finish CUP and PADDLE: 1010 Steel, zinc plated plus bright chromate dip or powder coated (black or satin silver) or 304 stainless steel, passivated and brushed finish (see table). GUIDE and SLIDE: 1010 Steel, zinc plated plus bright chromate dip or 304 stainless steel, passivated. SPRING: 302 Stainless steel, passivated. LOCKWASHER: Spring steel, zinc alloy plate, bright chromate plus sealer or 304 stainless steel, passivated. For 20 Series PIN: 302 Stainless steel, passivated. NUT: Steel, zinc plate, chromate plus sealer or stainless steel, passivated. BRACKET: 1010 Steel, zinc plate, chromate plus sealer or 304 stainless steel, passivated. STUD: 10B21 Steel, zinc alloy plate, bright chromate plus sealer or 302 stainless steel, passivated. For 300 Series RIVET: 430 Stainless steel, passivated. NUT: Steel, zinc plate, chromate plus sealer or 18-8 stainless steel, passivated. BRACKET: 1010 Steel, zinc plate, chromate plus sealer or 304 stainless steel, passivated. STUD: 10B21 Steel, zinc plate, chromate plus sealer or 18-9L10 stainless steel. For Locking Versions LOCK: Die-cast zinc, black powder coated or chrome plated.LOCK ARM: Steel, zinc alloy plate, bright chromate plus sealer or stainless steel, passivated. MOUNTING NUT: Die-cast zinc with chemical protective film. SCREWS: Steel, zinc plated plus yellow chromate dip or stainless steel, passivated. KEYS (2): Brass, nickel plated. * Locks are keyed alike. Different key codes are available. Contact Southco for details. Product Strength Guidelines Series 20 Maximum working load: 570 N (125 lbs.) Series 300 Maximum working load: 1110 N (250 lbs.) FINISH Brushed Stainless steel 64-10-301-50 without lock with lock* 64-10-302-50 Zinc plated Steel 64-10-301-40 64-10-302-40 Black powder coat 64-10-301-90 64-10-302-90 300 SERIES PART NUMBER (To assist in your product selection; samples are available for your evaluation.) Series 300