Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
+ SO Na S Na
S Na
The degree of reduction of sulfur in the white liquor is determined by the operation of the
recovery boiler. The Na
2
SO
4
is an inert circulating compound in the liquor system, and this
reduces process efficiency. A normal degree of reduction in recovery boilers is slightly above
90%.
Picture 18 shows the bottom of a recovery boiler with black liquor entering the boiler through the
liquor guns shown in Picture 19. Air is added above the bottom and the char bed in such a way
that reducing conditions are maintained near the char bed. The smelt flows from the recovery
boiler into the smelt dissolver.
Picture 18. Recovery boiler lower furnace with
hot char bed
Picture 19. Arrangement of a black liquor gun,
port opening and liquor spray
The recovery boiler has a risk of smelt and water explosion due to the presence of the porous hot
char bed containing molten sodium salts. The water and smelt can come into direct contact due to a
recovery boiler tube failure causing a smelt and water explosion in a recovery boiler. An emergency
rapid drain system minimizes potential damage. Water remains at the lowest part of the furnace to
provide cooling for the floor tubes. If all water drains from the floor tubes, the heat from the hot char
bed will damage the boiler tubes.
Fapet 6B: p.B113
KRB: p.8
16
The risk of a recovery boiler tube failure is
decreased and the use of corrosion resistant
materials in the recovery boiler has increased
the lifetime of a boiler. The materials vary in
different parts of the boiler according to the
conditions prevailing in the different parts of
the boiler. For instance, the lower portion of
the recovery boiler is often made of composite
tube material as shown in Picture 20. The
outer surface of the boiler tube is covered by
corrosion-resistant stainless steel. Also,
keeping the amounts of certain corrosive
chemicals, like chlorine and potassium, below
critical levels in the chemical recovery cycle
reduces corrosion.
Picture 20. Lower furnace arrangement with
composite tube wall construction
Recovery of heat in the recovery boiler
Picture 21 shows the material flows in a steam boiler such as a recovery boiler. A recovery boiler is
a steam boiler that has the following components or systems:
Black liquor handling and feeding equipment for feeding the thick black liquor into the boiler.
The black liquor is fed at a dry solids concentration above 65%, in some boilers built after 1990
the dry solids content is even over 80%. At high dry solids concentrations, the black liquor
becomes highly viscous and is difficult to handle unless kept at an elevated temperature.
Air fans, air ducts and air pre-heater. The combustion air is pre-heated in the recovery boiler
house and with air pre-heaters before being fed into the recovery boiler furnace.
Flue gas cleaning. The heat is recovered from the flue gas in the economizer and the flue gases
are cleaned with an electric precipitator to recover dust-containing sodium and sulfur.
Smelt outlet ducts.
Combustion chamber or furnace where the combustion of black liquor occurs.
Tubing for steam and water that forms the heat exchangers that cool the hot combustion gases.
Feed water system.
Control systems.
The recovery boiler produces superheated steam through the combustion of black liquor with air,
and the steam is taken to a turbine to produce power as shown in Picture 21. A higher
temperature and pressure of the superheated steam going to the turbine generates more power
from the heat generated in the boiler.
From the turbine, the steam for the pulp production process is taken out at two pressure levels:
extraction or high pressure steam with a pressure of about 12 bars that is used for instance to heat
the digester and back pressure or low pressure steam that is used for instance at the evaporation
plant and the pulp dryer. Primary condensate from the condensing of fresh live steam can be
returned to the feed water tank feeding the boiler with clean water as shown in Picture 22. Feed
water is usually preheated with steam. Exhaust steam from the turbine is taken to a surface
condenser.
KRB: p.12
17
Picture 21. Material flows in a steam boiler
Picture 22. Flow diagram of a cogeneration
steam cycle
The black liquor is combusted in the furnace of the recovery boiler. About 70%-75% of the heat
value of the black liquor will convert into superheated steam when the dry solids content of the
black liquor is 72%-85%. The smelt consumes heat due to the heat of the smelt and the chemical
reactions to form the reduced sulfur in the smelt. About 15% of the heat will go to the smelt.
The rest of the heat is lost with the flue gases. Picture 23 shows how the combustion heat is
divided between recovered heat, heat to smelt and heat losses in the flue gases as the flue gas
temperature and the dry solids content of the black liquor vary.
Picture 23. Black liquor dry solids heat to smelt, as loss in flue gases, and recovered into steam
Picture 24 shows the principle of the water system in a recovery boiler and Picture 25 a
perspective of the recovery boiler construction. Feed water is pumped into the boiler and enters
the first heat transfer surface or economizer (11). The water flows from the economizer to the
steam drum (6). In the steam drum, steam separates from water. Separation occurs by gravity,
Fapet 6B: p.B206
Fapet 6B: p.B207
Fapet 6B: p.B316
18
screens and cyclone separators in order to minimize the amount of water droplets in the steam.
Downcomers (7) feed saturated water to the evaporative surfaces that are the walls of the
combustion chamber in the boiler and tubes in the boiler bank. Saturated steam (12) exits from
the drum and flows through the superheaters (13) and is heated to superheated steam. The role
of superheaters is to heat the steam well above saturation before feeding the steam to the turbine.
11
12
13
10
6
7
11
12
13
10
6
7
11 11
12 12
13 13
10 10
66
77
Picture 24. Principle of a water tube boiler
The hot flue gases carrying the heat from combustion meet the heat surfaces in the following
order: superheater boiler bank economizer. The hottest gas heats the steam in the superheater
and the coldest gas heats the feed water interring the boiler. The boiling water cools the walls of
the boiler.
The feed water system of the recovery boiler
consists of the feed water tank (1), deaerator,
boiler feed water pump (2), control valve, and
feed water piping (3). The water from the
economizer generates clean attemperating
water (5) from steam in a sweet water
condenser (4). The attemperating water is
used to control the temperature of the steam in
the superheaters and thus to control the
surface temperature of the tubes in the
superheaters. Picture 26 shows some typical
superheater platens. The main steam valves
control steam flow (9). The steam from
superheaters flows through the main steam
line (10) to the turbine.
Picture 25. Water circulation system
Modified by KH;
Fapet 6B: p.B205
Fapet 6B: p.B122
19
Picture 26. Arrangement of two superheater
platens
Picture 27. Air system for a recovery boiler
The air is typically delivered at several horizontal elevations to ensure complete combustion and to
minimize emissions. In boilers built after the year 2000, air is often introduced over almost the
whole height of the furnace section of the recovery boiler. Picture 27 shows a boiler air system. It
has an inlet duct with silencer (1), venturi for airflow measurement (2), air blower (3), air heater (4),
distribution ducts (5), and air ducts (6 and 7). Pressure and temperature measuring devices are also
necessary at proper locations. Air intake is typically high inside the boiler house to ensure an even
vertical temperature profile and to recover heat losses through boiler walls and openings.
Recovery boiler operation
Spent kraft pulping liquors contain inorganic salts. During the combustion reactions, the
temperatures increase to levels where significant amounts of inorganic chemicals vaporize.
Small char fragments and black liquor particles also entrain into the flue gas flow. Combustion
and chemical reactions take place in the hot gas phase and cause deposits that collect on heat
transfer surfaces and foul them.
The deposits formed on the heat transfer surfaces consist mainly of Na
2
CO
3
, Na
2
SO
4
, Na
2
S and
small amounts of NaCl and potassium salts. The composition of the deposits varies according to
the mechanics of deposit formation, type of black liquor and combustion conditions. Deposits in
the lower part of the furnace generally contain more Na
2
CO
3
and Na
2
S and less Na
2
SO
4
, NaCl
and potassium salts that deposits in the upper furnace. Picture 28 shows typical compositions of
deposits in a recovery boiler.
KRB: p.13
Fapet 6B: p.B121
20
Picture 28. Composition of fireside deposits
The fouling of individual heat transfer surfaces is removed and controlled by soot blowing. Soot
blowing is done with steam and is directed to the critical heat transfer surfaces. Soot blowers are
usually in pairs on the left and right side of the boiler as shown in Picture 29. Picture 30 shows a
soot blower cleaning a tube bank.
Picture 29. Recovery boiler
Picture 30. Sketch of a soot blower cleaning a
tube bank
Potassium and chloride in the black liquor influence the fouling of heat transfer surfaces and the
corrosion of recovery boilers. Even small amounts of potassium and chloride influence the sticky
temperature of dust. The sticky temperature is the temperature above which dust contains sufficient
amounts of sodium in molten state to stick to the heat transfer surfaces and form deposits as shown
in Picture 31. The deposits of chemicals on the heat transfer surfaces become an effective barrier to
heat transfer from the flue gas to the tube wall. From the wall, the heat is transferred to the steam or
water inside the tube.
KRB: p.15
KRB: p.296
Fapet 6B: p.B9
21
T
gas
T
steam
Tube wall
Deposit
Steam
(water)
Flue gas
T
0
T
70
Q
.
Picture 31. Deposit on superheater
0
20
40
60
80
100
500 600 700 800 900 1000
Temperature [C]
P
e
r
c
e
n
t
m
e
l
t
[
w
t
-
%
]
T
flow
T
sticky
Picture 32. Different compositions give different
melting behavior
The chloride and potassium levels influence the melting behavior of dust in recovery boilers and
decrease the melting point of dust as shown in Picture 32. The graphs in the picture show the
melting behavior of some typical recovery boiler dusts with varying potassium and chlorine
content. Chloride levels at Scandinavian and North American mills are typically 0.2%-0.8% of
mass. Potassium levels at Scandinavian and North American mills can vary widely: 1%-4% of
mass. Chloride and potassium enter the chemical recovery cycle mainly with the wood and
enrich into the recovery cycle. The level of chloride and potassium must be kept sufficiently low.
The levels are controlled by purging dust from the recovery boiler as dust tends to enrich more in
chlorine and potassium compared to the rest of the recovery cycle.
Increasing chloride and potassium contents reduces the melting point of sodium-containing dust.
Only a few percentages on molten metals make the metals sticky. T
sticky
is the temperature when
enough sodium is in molten state and makes a dust particle stick to surfaces of the recovery boiler.
T
sticky
is usually in recovery boiler defined to the temperature when 15% of the metals are in molten
state. T
flow
is the temperature when enough sodium is in molten state to make the metal a flowing
smelt. Metals start to flow when over 70% is in molten form but usually in connection with recovery
boilers T
flow
is defined as the temperature when 85% of the metals are in molten state.
Picture 33 shows the material balance of a recovery boiler and how the generated steam is used
inside the boiler and as steam being fed to the turbine at the mill. Dust from the heating surfaces is
mixed with the black liquor and fed back into the boiler. Some of the dust may be purged from the
recovery cycle to control the content of non-process elements, in particular chloride and potassium.
KRB, MPS
KRB, MPS
22
Picture 33. Material balance based on 100kg of black liquor solids
White liquor preparation
Several separate processes are needed when converting the green liquor into white liquor: dregs
removal from green liquor, slaking of lime, causticizing reaction, white liquor separation from lime
mud with lime mud washing, and drying and reburning or calcining of lime. Picture 34 shows the
white liquor preparation system and the separate processes in the system.
Picture 34. A diagram of white liquor preparation and lime reburning
KRB: p.19
Fapet 6B: p.B162
23
Dregs removal from green liquor
Green liquor results when the smelt from the recovery boiler is dissolved in weak white liquor or
water in the dissolving tank. Green liquor is an aqueous solution mainly consisting of sodium
sulfides, sulfates and carbonates. It contains some unburned char and some non-process elements
that have a low solubility in the green liquor and that can be removed by sedimentation or filtration.
Most impurities in the lime cycle come from green liquor. Solid particles in green liquor mix with
the lime and accumulate in the lime cycle. Many of these impurities can be removed as dregs from
the green liquor. Without dregs separation, the need for lime makeup may be 30% of the lime
circulation. With good purification of green liquor, the lime makeup required can decrease to 3%-
5%. The separation of the solids, called dregs, from green liquor normally uses sedimentation or
filtration methods. Green liquor purification concepts in industrial use include:
Clarification
Sedimentation
Sludge blanket clarification
Filtration
Cake filtration with or without precoat
Cross flow filtration
The closing of the process cycles has led to an increased need to control the amount of non-process
elements in the recovery cycle by separating dregs in causticizing. The non-process elements enter
with wood and with chemicals used in the process as for instance magnesium used in oxygen
delignification. Table 7 shows an example of green liquor prior to and after filtration. The green
liquor treatment process in Picture 35 includes the following main process stages:
Separation of solid impurities and dregs from green liquor
Cooling of green liquor for causticizing
Treating the dregs for proper disposal
Picture 35. Green liquor treatment
Fapet 6B: p.B151
24
Table 7. Removal of various elements from green liquor
Raw green liquor Filtered liquor
Dregs, mg/l 310 7
Potassium (K), mg/l 5.3 5.3
Magnesium (Mg), mg/l 53 1.1
Aluminum (Al), mg/l 60 40
Iron (Fe), mg/l 17 8.2
Manganese (Mn), mg/l 16 2.2
Copper (Cu), mg/l 1.3 0.88
Phosphorus (P), mg/l 43.8 41.2
Green liquor can be clarified by sedimentation. In sedimentation, the density difference between the
solid material and the liquid in green liquor separates the solid material by allowing it to settle. A
clarifier is normally an open cylindrical tank as Picture 36 shows. The solid material that is heavier
than the liquid settles to the bottom of the clarifier to form sludge. The clear liquor in the upper part
of the clarifier is removed as an overflow.
Picture 36. A clarifier
In green liquor cross flow filters a thin film of green liquor fall onto a vertical filter cloth. Some
falling liquor is forced through the vertical filter cloth while most of the liquor including the dregs
continues to fall to the bottom in the film. The liquor is recirculated to the top of the filter to
maintain the film by pumping. Filtration continues and the sludge thickens in the circulation until
reaching the desired sludge density. Thickened sludge is discarded from the filter by the pressure
inside the filter.
Fapet 6B: p.B146
MPS
25
Picture 37. Cross-flow filter for green liquor
filtration
Picture 38. Green liquor cooler
It is necessary to cool the green liquor and to control the temperature of the green liquor that enters
the slaker in recausticizing to prevent the liquor from boiling in the slaker. Boiling may occur due to
the heat generated as a result of the exothermic slaking reaction. Cooling of green liquor, and even
of weak liquor, is difficult with indirect heat exchangers because of the rapid scaling and plugging
due to reduced solubility at lower temperatures.
Lime slaking and causticizing
Green liquor is mixed with calcium oxide, CaO, and the calcium oxide slakes with water and forms
calcium hydroxide, Ca(OH)
2
. The calcium hydroxide reacts with the Na
2
CO
3
in the green liquor to
produce NaOH and CaCO
3
. Picture 39 shows a slaker in which lime is slaked into green liquor.
Picture 39. Slaker
The slaking of lime is a strongly exothermic reaction:
CaO + H
2
O - Ca(OH)
2
+ 65 kJ/mol
The slaking reaction takes about 10-30 minutes to complete depending on the quality of lime. The
heat released due to the slaking reaction must be distributed evenly to the liquor by agitation to
avoid local overheating. The temperature of the solution has a major influence on the reaction rate.
Below 70C, the reaction rate is significantly slower than at the normal operating temperatures close
to 100C.
MPS
MPS
MPS
26
The causticizing reaction is an equilibrium reaction:
Ca(OH)
2
(s) + Na
2
CO
3
(aq) - 2 NaOH (aq) + CaCO
3
(s)
The reaction does not have any significant heat effect. Calcium hydroxide and CaCO
3
are insoluble
and participate in the reaction as solids. The causticizing reaction begins and continues to about 70%
completion during the slaking which takes 10-20 minutes.
The main purpose of the causticizer following the slaker is to give time to complete the causticizing
reaction that has already progressed to a completion rate of two-thirds in the slaker. The slaked lime
slurry (lime milk) must remain in the causticizers sufficiently long, and the liquor must have proper
contact with the lime mud particles at all times. A causticizer is shown in Picture 40.
The necessary residence time in the causticizer depends on the selected method for white liquor
separation. If white liquor is separated from lime by settling, a residence time of 1.5-2 hours is
adequate in the causticizer. The reactions can continue in the clarifiers. If a filter is used, the
residence time in the causticizers is usually about 2.5 hours as there is not much time for reactions in
the filter. Too short a residence time results in excessive amounts of unreacted calcium hydroxide,
which remains in the lime mud and will deteriorate the filterability properties and blind the filter
media with precipitated CaCO
3
during the separation of lime mud and white liquor.
Picture 40. Causticizer
The causticizing efficiency, that is the ratio between NaOH and NaOH plus Na
2
CO
3
in the white
liquor, is dependent primarily on the strength of the white liquor, expressed as total alkali per
volume of liquor. A higher strength will reduce causticizing efficiency according to Goodwin's
curve. Industrial white liquors have a causticizing efficiency or degree slightly above 80%.
Lime handling and washing
White liquor and lime mud are separated after causticizing. There are some different
technologies in use for the separation of white liquor and lime mud and for the washing of lime
mud. Picture 41 shows the water balance when a pressurized disc filter is used for white liquor
separation and lime mud washing. The separated lime mud is taken to the next stage of lime
mud washing and thickening.
Filtrate from lime mud washing and thickening is taken to smelt dissolving as weak wash liquor
or weak white liquor. After further treatment and drying, the washed lime mud is taken to the
lime kiln. In lime washing, condensates, and to some extent bleach plant filtrates, are used to
replace fresh water.
MPS
27
Picture 41. Water balance for causticizing with a pressurized disc filter for white liquor separation
Other commonly used machines for white liquor and lime mud separation and mud washing are
the candle filter shown in Picture 42 and the disc filter shown in Picture 43. The heat and water
balances when using these machines are somewhat different than the ones when using
pressurized disk filters.
Picture 42. A candle filter
Picture 43. Pressurized disc filtration for white
liquor separation and lime mud
washing
Fapet 6B: p.B169
MPS
MPS, Andritz
28
The white liquor produced and separated from the lime mud is taken to the digester for cooking.
Table 8 shows typical properties of white liquor.
Table 8. An example of white liquor composition
Compound Concentration,
g NaOH/l
Concentration,
g Na
2
O/l
As compound,
g/l
NaOH 95 73.6 95
Na
2
S 40 31.8 39
Na
2
CO
3
23 17.8 30.5
Na
2
SO
4
4 3.1 7.1
Na
2
S
2
O3 2 1.6 4.0
Na
2
SO
3
0.5 0.4 0.8
Other compounds - - 3.0
Effective alkali 135 105.4 -
Active alkali 115 89.5 -
Total alkali 164.5 128.3 179.4
Sulfidity, % 29.6
S/Na equivalent ratio 0.58
Causticizing degree, % 80.5
Reduction degree, %
based on total S
82.2
Reduction degree, %
based on total SO
4
90.9
The target in lime mud dewatering is to complete lime mud washing and increase the dry solids so
that the lime mud can be dried thermally and fed to the lime kiln. The moisture in the lime mud has
a considerable effect on the energy consumption of the lime kiln. Dry solids contents of 80%-90%
are possible after mechanical dewatering. The water soluble alkali content in the lime mud after
mechanical filter dewatering is under 0.1% as Na
2
O on dry mud. A low content of sodium is
necessary for the trouble-free operation of the lime kiln.
Picture 44. Lime mud washing and dewatering
Fapet 6B: p.B171
MPS
29
Lime drying and reburning
The lime reburning process is shown in Picture 45 and consists of the following unit operations:
Pumping of lime mud, that is CaCO
3
, from lime mud storage
Mechanical dewatering of lime mud to a high dry solids content
Thermal dewatering in the kiln or in a separate cyclone
Heating and calcining
Cooling of the lime, that is calcium oxide, product
Screening and crushing of lime
Conveying of lime to storage
Picture 45. Lime reburning process
The physical size of a rotary lime kiln, with a capacity of 500 to 550 tons of reburned lime/day, is
4m-4.5m in diameter and 100m-140m in length. The production of a kiln of this size matches a
white liquor production of about 7,000 m
3
/day, corresponding to a pulp production of slightly above
2,000 t/day. The kiln is supported by three or four piers.
Picture 46. Limekiln
A pneumatic dryer for lime mud is an emerging drying method where the lime is dried with the
exhaust gases from the limekiln in a separate cyclone. Lime mud is fed to a flue gas stream, where
the heat of the flue gases dries the mud. A cyclone separates dry mud and feeds it to the kiln as
shown in Picture 47.
Fapet 6B: p.B10
Fapet 6B: p.B179
30
Picture 47. A pneumatic dryer for lime mud
The traditional method for the drying of mud is the chain section of the rotary kiln. Picture 48 shows
a chain system. The length of the chain section of the limekiln is chosen so that the mud is
completely dry when leaving the chain section. The length of the chain section is usually about 20%
of the total kiln length.
Picture 48. Chain system
Lime reburning
Heating or reburning of lime mud converts lime mud to lime according to the following reaction:
CaCO
3
- CaO + CO
2
Dissociation of CaCO
3
to CaO and CO
2
starts when the temperature is above 820C. Increasing the
temperature accelerates the reaction. Reburning is done at a temperature of about 1,100C in order
to obtain sufficiently fast reaction rates.
Lime mud entering the limekiln also contains some unreacted lime CaO, water, a small amount of
alkali, other impurities and non-process elements. The amount of impurities in the lime mud is
typically about 7%-10% and depends on the amount of impurities introduced into the lime cycle
with the green liquor and the makeup lime. Non-process elements normally present in the lime cycle
are magnesium (Mg), aluminum (Al), silica (Si), phosphorus (P), iron (Fe), manganese (Mn) and
sulfur (S). Silica is a major problem when pulping annual plants or tropical wood. Sulfur comes for
instance from the burning of non-condensable gases in the lime kiln. Table 9 provides an example of
different lime compositions in the case of a Scandinavian mill and a mill for mixed tropical
hardwood. The major difference between the mill limes is in the content of silica.
Fapet 6B: p.B181
MPS, Andritz
31
Table 9. An example of different lime compositions
Component
(expressed as
oxides)
Makeup
lime
Scandinavian mill with
softwood or hardwood
as raw material
Mill with mixed
tropical hardwood
as raw material
CaO, wt. % 93 N/A N/A
Na
2
O, wt. % 0.06 N/A N/A
SiO
2
, wt. % 2.5 0.4 7.9
MgO, wt. % 1.3 1.3 1.2
Fe
2
O
3
, wt. % 0.5 0.06 0.4
MnO, wt. % 0.04 0.1 0.01
Silica is a serious impurity in the lime cycle and causes problems especially when pulping annual
plants and tropical wood. The lime mud becomes difficult to handle and dewater with an increasing
silica content as shown in Picture 49.
Picture 49. Lime mud dry substance and silica in lime mud
The cell structure of annual plants contains solid silica particles that dissolve in the cooking liquor,
proceed with the black liquor into the smelt, and end up in the green liquor in dissolved form. Silica
precipitates with lime mud during recausticizing because of the low solubility of calcium silicate in
white liquor. Lime mud from the pulping of annual plants cannot often be reburned at all. A large
portion of the lime mud from the pulping of tropical hardwood must be dumped to keep the
recausticizing plant in operation.
Depending on the design of the burner in the lime kilns, also fuels other than fuel oil and natural gas
can be used. A combination burner can have ports for non-condensable gases and arrangements for
feeding methanol. Primary air passes through the burner, cools it, and stabilizes the flame.
Fapet 6B: p.B148
Fapet 6B: p.B147
32
Picture 50. Burner
Picture 51. Temperature profile in the limekiln
Lime kilns have a refractory lining that protects the kiln shell from overheating and reduces the heat
loss to an acceptable level. The temperature distribution of lime kilns is wide from the cold feed-end
housing to the hot firing hood. In conventional kilns, where the mud is dried inside the kiln, the
lowest temperature is about 100C. In the flame zone, the temperature is about 1,250C. In large
kilns with a shell diameter of over 4.5m, the flame zone lining has to tolerate even higher
temperatures like 1,300C-1,350C. In modern kilns with a separate mud dryer, the cold-end
temperature is 400C-600C. Picture 52 shows the lime kiln brick lining zones. Each zone has a
lining of a certain material and thickness.
Picture 52. Lime kiln brick lining zones
Fapet 6B: p.B180
Fapet 6B: p.B163
Fapet 6B: p.B184
33
Questions
1. The source of water, organic material and inorganic material in black liquor. / Mustalipen
sisltmn veden, orgaanisen aineen ja eporgaanisen aineen alkuper.
2. Properties of black liquor influencing the evaporation plant. / Mustalipen ominaisuudet
haihduttamon kannalta.
3. Multistage evaporation plant, number of stages and steam consumption, soap separation. /
Monivaihehaihduttamo, vaiheiden lukumr ja hyrynkulutus, suovan erotus.
4. The most common evaporator designs used in black liquor evaporation. / Yleisimmt
haihdutinkonstruktiot mustalipen haihdutuksessa.
5. Condensate handling and reuse at kraft pulp mills. / Lauhteiden ksittely ja uudelleenkytt
sulfaattisellutehtailla.
6. List the main steps of the kraft recovery process. / Luettele sulfaattiprosessin
talteenottopuolen trkeimmt vaiheet.
7. The smelt reactions in a recovery boiler. / Sulareaktiot soodakattilassa.
8. The combustion of black liquor in a recovery boiler; the black liquor droplet during
combustion, and the different stages of combustion. / Mustalipen poltto soodakattilassa;
mustalipepisaran kyttytyminen polton aikana ja palamisen eri vaiheet.
9. Recovery of heat in a recovery boiler. / Soodakattilan energian talteenottojrjestelm.
10. Scaling of heat transfer surfaces in the recovery boiler. / Soodakattilan lmmnsiirtopintojen
likaantuminen.
11. The main factors influencing the heating value of black liquors. / Polttoarvoon vaikuttavat
trkeimmt tekijt.
12. Influence of chlorine and potassium on recovery boiler operation; what can be done to
control chlorine and potassium levels? / Kloorin ja kaliumin vaikutus soodakattilan
toimintaan; mit voidaan tehd kloori- ja kaliumtasojen hallitsemiseksi.
13. Green liquor treatment, measures to reduce the need for makeup lime. / Viherlipen
ksittely, miten vhennetn korvauskalkin tarvetta.
14. Slaking of lime and causticizing reactions. / Kalkin sammutus ja kaustisointireaktiot.
15. The operation principle and construction of the lime kiln. / Meesauunin toimintaperiaate ja
rakenne.