Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Page1of24
Page2of24
Dos and Donts in Laboratory :
1.Do not handle any equipment before reading the instructions /Instruction manuals.
2.Read carefully the power ratings of the equipment before it is switched ON, whether ratings
230 V/50 Hz or 115V/60 Hz. For Indian equipment, the power ratings are normally 230V/50Hz.
If you have equipment with 115/60 Hz ratings, do not insert power plug, as our normal supply is
230V/50Hz., which will damage the equipment.
3.Observe type of sockets of equipment power to avoid mechanical damage.
4.Do not forcefully place connectors to avoid the damage.
5.Strictly observe the instructions given by the Teacher/ Lab Instructor.
Instruction for Laboratory Teachers:-
1.Submission related to whatever lab work has been completed should be done during the next
lab session.
2.Students should be instructed to switch on the power supply after getting the
checked by the lab assistant / teacher. After the experiment is over, the students must hand over
the circuit board, wires, CRO probe to the lab assistant/teacher.
3.The promptness of submission should be encouraged by way of marking and
evaluation patterns that will benefit the sincere students.
CSPIT EC 208 Analog Electronics Circuits
Page3of24
Practical-1
Aim :-To plot forward characteristics of pn junction diode (If vs. Vf)
Apparatus :-D.C.regulated power supply (0-30V) , Diode(1N4007), Resistance (820 ),
voltmeter, ammeter (0-25mA) Connecting wires
Circuit Diagram :
Procedure:-
1. 1. Connect the circuit as shown in fig.
2. 2. By varying applied voltage measure corresponding reading for voltage & current.
3. 3. Plot the graph of voltage & forward current.
Observations:-
Input voltage (Vdc) = -------V
CSPIT EC 208 Analog Electronics Circuits
Page4of24
Applied voltage
Vdc ( V)
O/P Voltage Vf ( V) Current If ( mA)
Result:-Current increases exponentially with respect to voltage after cut in voltage as seen
from the graph
CSPIT EC 208 Analog Electronics Circuits
Page5of24
Practical-2, 3 & 4
Aim :- To study and perform Half-wave and full wave rectifiers with
filters
Theory: -
The diode rectifier converts the input sinusoidal voltage Vs to a unipolar out Vo. There are two
types of rectifier circuits:
1. Half-wave Rectifier and
2. Full-wave Rectifier.
Apertures: -
1.Trainer Board
2. Multimeter
3. Resistor 10K
4. Capacitor 1F, 47F
5. Diode Four Pieces
6. Oscilloscope
7. Signal Generator
8. Wire.
CSPIT EC 208 Analog Electronics Circuits
Page6of24
Page7of24
Page8of24
Page9of24
Practical-5
TRANSISTOR COMMON -BASE CONFIGURATION
AIM: 1.To observe and draw the input and output characteristics of a transistor connected
in common base configuration.
2. To find of the given transistor.
APPARATUS: Transistor, BC 107
Regulated power supply (0-30V, 1A)
Voltmeter (0-20V)
Ammeters (0-100mA)
Resistor, 1000
Bread board
Connecting wires
THEORY:
A transistor is a three terminal active device. The terminals are emitter, base,
collector. In CB configuration, the base is common to both input (emitter) and output
(collector). For normal operation, the E-B junction is forward biased and C-B junction is
reverse biased.
In CB configuration, I
E
is +ve, I
C
is ve and I
B
is ve. So,
V
EB=
f1 (V
CB,
I
E
) and
I
C=
f2 (V
CB,
I
B)
With an increasing the reverse collector voltage, the space-charge width at the
output junction increases and the effective base width W decreases. This phenomenon is
known as Early effect. Then, there will be less chance for recombination within the base
region. With increase of charge gradient with in the base region, the current of minority
carriers injected across the emitter junction increases.The current amplification factor of
CB configuration is given by,
= I
C
/ I
E
CIRCUIT DIAGRAM
CSPIT EC 208 Analog Electronics Circuits
Page10of24
PROCEDURE:
INPUT CHARACTERISTICS:
1. Connections are made as per the circuit diagram.
2. For plotting the input characteristics, the output voltage V
CE
is kept constant at 0V and
for different values of V
EB
note down the values of I
E
.
3. Repeat the above step keeping V
CB
at 2V, 4V, and 6V.All the readings are tabulated.
4. A graph is drawn between V
EB
and I
E
for constant V
CB.
OUTPUT CHARACTERISTICS:
1. Connections are made as per the circuit diagram.
2. For plotting the output characteristics, the input I
E
is kept constant at 10m A and for
different values of V
CB
, note down the values of I
C.
3. Repeat the above step for the values of I
E
at 20 mA, 40 mA, and 60 mA, all the readings
are tabulated.
4. A graph is drawn between V
CB
and Ic for constant I
E
CSPIT EC 208 Analog Electronics Circuits
Page11of24
OBSERVATIONS:
INPUT CHARACTERISTICS:
S.No V
CB=
0V V
CB=
1V V
CB
=2V
V
EB
(V) I
E(
mA) V
EB
(V) I
E(
mA) V
EB
(V) I
E(
mA)
OUTPUT CHARACTERISTICS:
S.No
I
E=
10mA I
E=
20mA I
E
=30mA
V
CB
(V) I
C(
mA) V
CB
(V) I
C(
mA) V
CB
(V) I
C(
mA)
MODEL GRAPHS:
INPUT CHARACTERISTICS
CSPIT EC 208 Analog Electronics Circuits
Page12of24
OUTPUT CHARACTERISTICS
PRECAUTIONS:
1. The supply voltages should not exceed the rating of the transistor.
2. Meters should be connected properly according to their polarities.
RESULT:
1. The input and output characteristics of the transistor are drawn.
2. The of the given transistor is calculated.
CSPIT EC 208 Analog Electronics Circuits
Page13of24
Practical-6
TRANSISTOR CE CHARACTERSTICS
AIM: 1. To draw the input and output characteristics of transistor connected in
CE configuration
2. To find of the given transistor.
APPARATUS:
Transistor (BC 107)
R.P.S (O-30V) 2Nos
Voltmeters (0-20V) 2Nos
Ammeters (0-200A)
(0-500mA)
Resistors 1Kohm
Bread board
THEORY:
A transistor is a three terminal device. The terminals are emitter, base, collector.
In common emitter configuration, input voltage is applied between base and emitter
terminals and out put is taken across the collector and emitter terminals.
Therefore the emitter terminal is common to both input and output.
The input characteristics resemble that of a forward biased diode curve. This is
expected since the Base-Emitter junction of the transistor is forward biased. As compared
to CB arrangement I
B
increases less rapidly with V
BE .
Therefore input resistance of CE
circuit is higher than that of CB circuit.
The output characteristics are drawn between I
c
and V
CE
at constant I
B.
the
collector current varies with V
CE
unto few volts only. After this the collector current
becomes almost constant, and independent of V
CE.
The value of V
CE
up to which the
collector current changes with V
CE
is known as Knee voltage. The transistor always
operated in the region above Knee voltage, I
C
is always constant and is approximately
equal to I
B.
The current amplification factor of CE configuration is given by
= I
C
/I
B
CSPIT EC 208 Analog Electronics Circuits
Page14of24
CIRCUIT DIAGRAM:
PROCEDURE:
INPUT CHARECTERSTICS:
1. Connect the circuit as per the circuit diagram.
2. For plotting the input characteristics the output voltage V
CE
is kept constant at 1V and for
different values of V
BE
. Note down the values of I
C
3. Repeat the above step by keeping V
CE
at 2V and 4V.
4. Tabulate all the readings.
5. plot the graph between V
BE
and I
B
for constant V
CE
OUTPUT CHARACTERSTICS:
1. Connect the circuit as per the circuit diagram
2. for plotting the output characteristics the input current I
B
is kept constant at 10A and
for different values of V
CE
note down the values of I
C
3. repeat the above step by keeping IB at 75 A 100 A
4. tabulate the all the readings
5. plot the graph between V
CE
and I
C
for constant I
B
CSPIT EC 208 Analog Electronics Circuits
Page15of24
OBSERVATIONS:
INPUT CHARACTERISTICS:
S.NO
V
CE
= 1V V
CE
= 2V V
CE
= 4V
V
BE
(V) I
B
(A) V
BE
(V) I
B
(A) V
BE
(V) I
B
(A)
OUT PUT CHAREACTARISTICS:
S.NO
I
B
= 50 A I
B
= 75 A I
B
= 100 A
V
CE
(V) I
C
(mA) V
CE
(V) I
C
mA) V
CE
(V) I
C
(mA)
MODEL GRAPHS:
INPUT CHARACTERSTICS:
CSPIT EC 208 Analog Electronics Circuits
Page16of24
OUTPUT CHARECTERSTICS:
PRECAUTIONS:
1. The supply voltage should not exceed the rating of the transistor
2. Meters should be connected properly according to their polarities
RESULT:
the input and out put characteristics of a transistor in CE configuration are Drawn
the plot of a given transistor is calculated
Page17of24
Practical-7
Aim: To study and perform Single stage transistor amplifier.
Brief Theory:
RC-coupled CE amplifier is widely used in audio frequency applications in radio and TV receivers. It
provides current, voltage and power gains. Base current controls the collector current of a common
emitter amplifier. A small increase in base current results in a relatively large increase in collector current.
Similarly, a small decrease in base current causes large decrease in collector current. The emitter-base
junction must be forward biased and the collector base junction must be reverse biased for the proper
functioning of an amplifier. In the circuit diagram, an NPN transistor is connected as a common emitter
ac amplifier. R
1
and R
2
are employed for the voltage divider bias of the transistor. Voltage divider bias
provides good stabilization independent of the variations of . The input signal V
in
is coupled through C
ci
to the base and output voltage is coupled from collector through the capacitor Cc2.
The input impedance of the amplifier is expressed as Z
in
= R
1
||R
2
||(1 + h
FE
r
e
) and output impedance as
Z
out
= R
c
||R
L
where r
e
is the internal emitter resistance of the transistor given by the expression = 25
mV/I
E
, where 25 mV is temperature equivalent voltage at room temperature.
Circuit Diagram:
CSPIT EC 208 Analog Electronics Circuits
Page18of24
Procedure
1. Test all the components using a multimeter. Set up the circuit and verify dc bias conditions. To
check dc bias conditions, remove input signal and capacitors in the circuit.
2. Connect the capacitors in the circuit. Apply a 100 mV peak to peak sinusoidal signal from the
function generator to the circuit input. Observe the input and output waveforms on the CRO screen
simultaneously.
3. Keep the input voltage constant at 100 mV, vary the frequency of the input signal from 0 to 1 MHz
or highest frequency available in the generator. Measure the output amplitude corresponding to
different frequencies and enter it in tabular column.
4. Plot the frequency response characteristics on a graph sheet with gain in dB on y-axis and logf on x-
axis. Mark log f
L
and log f
H
corresponding to 3 dB points. (If a semi-log graph sheet is used instead
of ordinary graph sheet, mark f along x-axis instead of logf).
5. Calculate the bandwidth of the amplifier using the expression BW= f
H
f
L
.
6. Remove the emitter bypass capacitor CE from the circuit and repeat the steps 3 to 5 and observe
that the bandwidth increases and gain decreases in the absence of CE .
Observation Table:
f (Hz) Vi Vo Gain f (Hz) Vi Vo Gain
CSPIT EC 208 Analog Electronics Circuits
Page19of24
Expected Results:
Conclusion:
With CE:
Mid-band gain of the amplifier = ..............
Bandwidth of the amplifier = ............. Hz
Without CE:
Mid-band gain of the amplifier = ...............
Bandwidth of the amplifier = ............... Hz
CSPIT EC 208 Analog Electronics Circuits
Page20of24
Practical-9
FET CHARACTERISTICS
AIM: a). To draw the drain and transfer characteristics of a given
FET.
b). To find the drain resistance (r
d
) amplification factor () and
Tran conductance (g
m
) of the given FET.
APPARATUS: FET (BFW-11)
Regulated power supply
Voltmeter (0-20V)
Ammeter (0-100mA)
Bread board
Connecting wires
THEORY:
A FET is a three terminal device, having the characteristics of high input impedance and
less noise, the Gate to Source junction of the FET s always reverse biased. In response to
small applied voltage from drain to source, the n-type bar acts as sample resistor, and the
drain current increases linearly with V
DS.
With increase in I
D
the ohmic voltage drop
between the source and the channel region reverse biases the junction and the conducting
position of the channel begins to remain constant. The V
DS
at this instant is called pinch of
voltage.
If the gate to source voltage (V
GS
) is applied in the direction to provide
additional reverse bias, the pinch off voltage ill is decreased.
In amplifier application, the FET is always used in the region beyond the
pinch-off.
F
DS
=I
DSS
(1-V
GS
/V
P
)^2
CIRCUIT DIAGRAM
CSPIT EC 208 Analog Electronics Circuits
Page21of24
PROCEDURE:
1. All the connections are made as per the circuit diagram.
2. To plot the drain characteristics, keep V
GS
constant at 0V.
3. Vary the V
DD
and observe the values of V
DS
and I
D
.
4. Repeat the above steps 2, 3 for different values of V
GS
at 0.1V and 0.2V.
5. All the readings are tabulated.
6. To plot the transfer characteristics, keep V
DS
constant at 1V.
7. Vary V
GG
and observe the values of V
GS
and I
D
.
8. Repeat steps 6 and 7 for different values of V
DS
at 1.5 V and 2V.
9. The readings are tabulated.
10. From drain characteristics, calculate the values of dynamic resistance (r
d
) by using the
formula
r
d =
V
DS
/I
D
11. From transfer characteristics, calculate the value of transconductace (g
m
) By using the
formula
G
m=
I
D
/V
DS
12. Amplification factor () = dynamic resistance. Tran conductance
= V
DS
/V
GS
CSPIT EC 208 Analog Electronics Circuits
Page22of24
OBSERVATIONS:
DRAIN CHARACTERISTICS
:
S.NO V
GS
=0V V
GS
=0.1V V
GS=
0.2V
V
DS
(V) I
D
(mA) V
DS
(V) I
D
(mA) V
DS
(V) I
D
(mA)
TRANSFER CHARACTERISTICS:
S.NO V
DS
=0.5V V
DS
=1V V
DS
=1.5V
V
GS
(V) I
D
(mA) V
GS
(V) I
D
(mA) V
GS
(V) I
D
(mA)
CSPIT EC 208 Analog Electronics Circuits
Page23of24
MODEL GRAPH:
TRANSFER CHARACTERISTICS
DRAIN CHARACTERISTICS
CSPIT EC 208 Analog Electronics Circuits
Page24of24
PRECAUTIONS:
1. The three terminals of the FET must be care fully identified
2. Practically FET contains four terminals, which are called source, drain, Gate, substrate.
3. Source and case should be short circuited.
4. Voltages exceeding the ratings of the FET should not be applied.
RESULT :
1. The drain and transfer characteristics of a given FET are drawn
2. The dynamic resistance (r
d
), amplification factor () and Tran conductance (g
m
) of the
given FET are calculated.