Sei sulla pagina 1di 112

1.

Which of the following factors determines the OSPF router ID


when configuring a router with both physical and logical
interfaces?
. !he lowest networ" number of any interface.
#. !he highest networ" number of any interface.
$. !he highest IP address of any logical interface.
D. !he middle IP address of any logical interface.
%. !he lowest IP address of any physical interface.
F. !he highest IP address of any physical interface.
&. !he lowest IP address of any logical interface.
nswer' $
(. Which of the following routes will be used to forward data in
a situation where a routing table contains static) *IP) and I&*P
routes destined to the same networ" with each set to its default
administrati+e distance?
. !he *IP route
#. !he static route
$. !he I&*P route
D. ll three will load balance.
nswer' #
,. !he following e-hibit shows the !est.ing.com W/. Study it
carefully'
What are the broadcast addresses of the subnets in the !est.ing
networ"? 0Select three options.1
. 12(.13.4(.(55
#. 12(.13.65.(55
$. 12(.13.3,.(55
D. 12(.13.7(.(55
%. 12(.13.,2.(55
F. 12(.13.26.(55
nswer' #)%)F
5. 8ou are a networ" administrator at !est.ing. !he !est.ing
networ" is illustrated in the following e-hibit. Study it
carefully'
*outers !est.ing1 and !est.ing( are connected through their
social interfaces) howe+er) they cannot communicate. 8ou
ascertain that !est.ing1 has the correct configuration.
$an you identify the fault on router !est.ing(?
. 9in" reliability is insufficient
#. IP$P is not open
$. Incorrect subnet mas"
D. Incompatible encapsulation
%. #andwidth allocation is too low
F. Incomplete IP address
nswer' D
3. 8ou are a networ" administrator at !est.ing. !he !est.ing
networ" is illustrated in the following e-hibit. Study it
carefully'
8ou want to pre+ent users on the *esearch /etwor" and the
Internet from accessing the !est.ing
Support ser+er) but you want to allow all other !est.ing users
access to the ser+er. 8ou create an access control list 0$91
called research bloc". !he $9 contains the following statements'
deny 12(.13.1:(.: :.:.:.(55 12(.13.1:,.(55 :.:.:.:
permit 12(.13.:.: :.:.(55.(55 12(.13.1:,.(5( :.:.:.:
Which of the following command se;uence must be issued so that
the list meets these re;uirements?
. !est.ing10config1< interface e:
!est.ing10config=if1< ip access=group research>bloc" in
#. !est.ing(0config1< interface s1
!est.ing(0config=if1< ip access=group research>bloc" in
$. !est.ing70config1< interface s1
!est.ing70config=if1< ip access=group research>bloc" in
D. !est.ing10config1< interface s:
!est.ing10config=if1< ip access=group research>bloc" out
%. !est.ing(0config1< interface s:
!est.ing(0config=if1< ip access=group research>bloc" out
F. !est.ing70config1< interface e:
!est.ing70config=if1< ip access=group research>bloc" out
nswer' F
2. 8ou are a networ" administrator at !est.ing. 8ou are
troubleshooting a router problem. 8ou issue the show ip route
command on one of the routers. !he output from the command is
shown in the following e-hibit'
What does ?1(:@7A represent?
. 1(: is the bandwidth allocation and 7 is the routing process
number.
#. 1(: is the administrati+e distance and 7 is the metric for
that route.
$. 1(: is the +alue of the update timer and 7 is the number of
updates recei+ed.
D. 1(: is the BDP port for forwarding traffic and 7 is the number
of bridges.
nswer' #
4. What is the basic characteristic of switches and hubs?
. Cubs cannot filter frames.
#. Bsing hubs is costly with regard to bandwidth a+ailability.
$. Switches do and can not forward broadcasts.
D. Switches are more efficient than hubs in processing frames.
%. Switches increase the number of collision domains in the
networ".
nswer' %
6. When you consider half=duple- and full=duple- %thernet) what
are uni;ue for half=duple- %thernet?0Select two options.1
. Calf=duple- %thernet operates in a shared collision domain.
#. Calf=duple- %thernet operates in an e-clusi+e broadcast
domain.
$. Calf=duple- %thernet has efficient throughput.
D. Calf=duple- %thernet has lower effecti+e throughput.
%. Calf=duple- %thernet operates in an e-clusi+e collision
domain.
nswer' )D
1:. Which PPP authentication methods will you use when
configuring PPP on an interface of a $isco router?0Select two
options.1
. SS9
#. S9IP
$. PP
D. 9P#
%. $CP
F. D/P
nswer' $)%
11. Study the %-hibit below carefully'
What is the function of the Frame *elay D9$I with regard to
!est.ing?
. Defines the signaling standard between !est.ing and
!est.ing#)
#. Identifies the type of encapsulation in operation between
!est.ing and !est.ing#.
$. Identifies the circuit between !est.ing and the frame switch.
D. Defines the signaling standard between !est.ing and the frame
switch.
nswer' $
1(. What could be the rationale behind using passi+e=interface
command when configuring a router?
. llows interfaces to share common IP addresses.
#. llows an interface to remain up without the aid of
"eepali+es.
$. llows a router to send routing and not recei+e updates +ia
that interface.
D. llows a routing protocol to forward updates that is missing
its IP address.
%. llows a router to recei+e routing updates on an interface but
not send updates +ia that interface.
nswer' %
17. 8ou are a networ" administrator at !est.ing. !he !est.ing
networ" is illustrated in the following e-hibit. Study it
carefully'
!est.ing is ac;uiring a new $lass $ IP networ".
Which of the following subnet mas"s will pro+ide one useful
subnet for each department while still ma"ing allowance for
enough usable host addresses per department as specified in the
graphic?
. (55.(55.(55.1(4
#. (55.(55.(55.16(
$. (55.(55.(55.((,
D. (55.(55.(55.(,:
%. (55.(55.(55.(,4
F. (55.(55.(55.(5(
nswer' $
1,. 8ou are a networ" administrator at !est.ing. 8ou need to
troubleshoot the !est.ing networ" shown in the e-hibit. Study the
%-hibit carefully'
!he host) !.1) is connected to the !est.ing1 9/) but it cannot
get access to resources on any of the other networ"s. !he hostEs
configuration is as follows'
host address' .....16(.134.133.,5
subnet mas"' ......(55.(55.(55.(,:
default gateway' ..16(.134.133.7(
!hen which of the following is the cause of the problem?
. !he default gateway is a networ" address.
#. !he default gateway is on a different subnet address as the
host.
$. !he IP address of the host is on a different subnet.
D. !he host subnet mas" is incompatible to the subnet mas" of the
attached router interface.
nswer'
15. What are the benefits of using a router to segment the
networ" at a main office? 0Select two options.1
. #roadcasts are not forwarded across the router.
#. #roadcasts are eradicated.
$. dding a router to the networ" decreases latency.
D. Filtering can occur based on 9ayer 7 information.
%. *outers are more efficient than switches.
nswer' )D
13. 8ou are a networ" technician at !est.ing. !est.ing has a
larger 12(.1(.:.: networ" that you want to di+ide into subnets.
8ou want each subnet to support ,56 hosts. 8ou also want to
pro+ide the ma-imum number of subnets.
Which networ" mas" should you use?
. (55.(55.:.:.
#. (55.(55.1(4.:.
$. (55.(55.((,.:.
D. (55.(55.(5,.:.
nswer' D
12. 8our new Funior !est.ing trainee) *utger) has a problem with
basic binary math. Ce must con+ert the binary number 1::111:1
into its decimal and he-adecimal e;ui+alent. Which two numbers
must *utger pro+ide? 0Select two options1
. 154
#. :-6D
$. 153
D. 152
%. :-16
F. :-6F
nswer' #)D
(1. Which of the following commands will you use to display the
configuration register setting on a router?
. show boot
#. show flash
$. show register
D. show +ersion
%. show config
nswer' D
((. 8ou are a networ" administrator at !est.ing. 8ou must
configure a new subnetwor" at the !est.ing branch office in
#erlin. 8ou ha+e been pro+ided with the subnet mas" of
(55.(55.(55.((,. 8ou want to assign IP addresses to hosts on the
subnet.
Which of the following IP addresses would you use? 0$hoose 7.1
. 13.(7.114.37
#. 42.,5.13.156
$. 6(.11.124.67
D. 17,.124.14.53
%. 16(.134.13.42
F. (12.134.133.16(
nswer' $)D)%
(7. 8ou are a networ" technician at !est.ing. 8ou need to
configure Frame *elay on a $isco router.
What is the default 9GI 09ocal Ganagement Interface1 frame type
transmitted by the $isco router on a Frame *elay circuit?
. I%!F
#. #4HS
$. /SI
D. $isco
%. I677a
nswer' D
(,. 8ou are a networ" technician at !est.ing. 8ou ha+e subnetted
the (1:.1:3.1,.: networ" with a @(, mas".
8our super+isor as"s you how many usable subnetwor"s and usable
host addresses per subnet this would ma"e pro+ision for.
What would your response be?
. 1 networ" with (5, hosts
#. , networ"s with 1(4 hosts
$. ( networ"s with (, hosts
D. 3 networ"s with 3, hosts
%. 4 networ"s with 73 hosts
nswer'
(5. 8ou are a networ" technician at !est.ing. Due to rapid
e-pansion) !est.ing is leaning towards scalable W/ technology.
Immediate plans for the company include an additional 2 regional
offices with all sites re;uiring continuous connecti+ity) but the
current head office has no free ports a+ailable.
Which of the following W/ technologies will meet the
re;uirements?
. Frame *elay
#. #roadband cable
$. ISD/=#*I
D. DS9
%. Dedicated PPP@CD9$ lin"s
F. ISD/
nswer'
(3. 8ou are a networ" technician at !est.ing. 8ou apply the
access list illustrated below to interface %: on a $isco router.
!he interface is connected to the 16(.134.1.4@(6 9/.
access=list 1(7 deny tcp 16(.134.133.14 :.:.:.2 e; (: any
access=list 1(7 deny tcp 16(.134.133.14 :.:.:.2 e; (1 any
What are the conse;uences of this specific access list?
. ll traffic will be allowed to e-it %: e-cept F!P traffic.
#. F!P traffic from 16(.134.133.16 to any host will be denied.
$. F!P traffic from 16(.134.133.(( to any host will be denied.
D. ll traffic e-iting %: will be denied.
%. ll F!P traffic to networ" 16(.134.133.14@(6 from any host
will be denied.
nswer' D
(2. What are the characteristic of lin" state routing protocols?
0$hoose 7.1
. !he e-change of ad+ertisement is triggered by a change in the
networ".
#. ll routers e-change routing tables with each other iIn a
multipoint networ".
$. Pac"ets are routed based upon the shortest path to the
destination.
D. Paths are chosen depending on the cost efficiency factor.
%. %+ery router in an OSPF area is capable of representing the
entire networ" topology.
F. Only the designated router in an OSPF area can represent the
entire networ" topology.
nswer' )$)%
(6. Which of the following are typical 9ayer ( encapsulations for
a W/ lin"? 0$hoose 7.1
. %thernet
#. PPP
$. !o"en *ing
D. CD9$
%. Frame *elay
F. PO!S
nswer' #)D)%
71. 8ou are a networ" technician at !est.ing. 8ou use a $isco
router to di+ide the !est.ing networ" into two separate segments)
!est.ing1 and !est.ing(. !he !est.ing $%O is concerned about the
cost) and wants to "now what the purpose of your action is.
What should you tell him?
. It decreases the number of broadcast domains.
#. It ma"es broadcasting domains more efficient between segments.
$. It increases the number of collisions.
D. It pre+ents segment 1Es broadcasts from getting to segment (.
%. It connects segment 1Es broadcasts to segment (.
nswer' D
7(. 8ou are a networ" technician at !est.ing. newly appointed
trainee wants to "now what the basics of distance +ector and lin"
state routing protocols are.
What would your reply be? 0$hoose (.1
. Distance +ector protocols send the entire routing table to
directly connected neighbors.
#. Distance +ector protocols are responsible for sending updates
to all networ"s listed in the routing table.
$. 9in" state protocols are responsible for sending the entire
routing table to the whole networ".
D. 9in" state protocols send updates regarding their own lin"s
status to all other routers on the networ".
nswer' )D
77. Which of the following statements is true regarding the split
horiJon rule?
. Distance +ector protocols need fall bac" routes that are
responsible for momentary loops.
#. /etwor"s can only remain fully operational pro+ided all
information is sent out all acti+e interfaces.
$. %ach S must "eep routing tables con+erged to a+oid dead
routes from being ad+ertised.
D. Information about a route should not be sent bac" in the
direction from which the original update came.
%. Only routers can split boundaries 0horiJons1 between
concentric networ"s.
nswer' D
75. 8ou are a networ" technician at !est.ing. 8ou are wor"ing
with a (5:: series $isco router. 8ou are performing the password
reco+ery procedure. 8ou ha+e Fust typed the following command'
o@r :-(1,(
8our newly appointed trainee is curious about why this command is
used.
What should you tell him?
. It is used to restart the router.
#. It is used to bypass the configuration in /D*G.
$. It is used to enter *OG Gonitor mode.
D. It is used to +iew the lost password.
%. It is used to sa+e the changes to the configuration.
nswer' #
73. 8ou are a networ" technician at !est.ing. 8ou ha+e told a
newly appointed trainee that the OSI model has 2 layers and that
the pplication layer is the highest layer. !he trainee is
curious as to which protocols operate at the application layer.
What should you tell him? 0$hoose (.1
. !$P
#. !elnet
$. F!P
D. *P
%. IP
nswer' #)$
74. 8ou are a networ" administrator at !est.ing. 8ou need to
configure fi+e new routes urgently for testing purposes. While
connected to a router by console) you copy and past a
configuration from a te-t file into the Cyper!erminal window.
Part of the te-t file is shown in the following e-hibit'
s a result of this procedure) host 16(.134.1:.1:@(6 would not be
able to ping the %thernet interface of the router. Why?
. !he new configuration must be sa+ed to the /D*G before the
changes can be effected.
#. !he subnet mas" on the router results is miscommunication.
$. !he %thernet networ" does not feature in the routing table due
to imcomplete *IP configuration.
D. !he copied configuration did not o+erwrite the shutdown
command on the %thernet interface.
%. !he router needs to be rebooted before the changes are
effected.
nswer' D
76. 8ou are a networ" administrator at !est.ing. !he !est.ing
networ" has three remote networ"s are accessed through serial :@:
interface on the test"ing1 router. !he remote networ"s are'
12(.13.1:.:)
12(.13.(:.:) and 12(.13.7:.:. Cowe+er) users cannot access
12(.13.(:.:. 8ou are troubleshooting the problem. 8ou issue the
debug ip rip and show ip route commands. !he output form the
command is shown in the following e-hibit'
What is the most li"ely cause of the problem?
. 12(.13.(:.: is not located in test"ing1Es routing table.
#. !here is no gateway of last resort on test"ing1.
$. !he static route for 12(.13.(:.: is incorrect.
D. !he test"ing1 router is not recei+ing 12(.13.(:.: updates.
nswer' $
,:. 8ou ha+e subnetted the (17.1:5.2(.: networ" with a @(4 mas".
Cow many usable subnetwor"s and usable host addresses per subnet
will be pro+ided?
. ( networ"s with 3( hosts
#. 3 networ"s with 7: hosts
$. 13 networ"s and 13 hosts
D. 3( networ"s and ( hosts
%. 1, networ"s and 1, hosts
nswer' %
,1. 8ou are a networ" technician at !est.ing) Inc. 8ou are
currently troubleshooting a $isco router. 8ou issue the show ip
route command. !he output from the command is displayed in the
following e-hibit'
Which route will not be entered into the routing table of a
neighboring router?
. * 16(.134.11.:@(, ?1(:@2A +ia 16(.134.6.1) ::'::':7) Serial1
#. $ 16(.134.1.:@(, is directly connected) %thernet:
$. * 16(.134.4.:@(, ?1(:@1A +ia 16(.134.(.() ::'::'1:) Serial:
D. * 16(.134.5.:@(, ?1(:@15A +ia 16(.134.(.() ::'::'1:) Serial:
nswer' D
,(. 8ou are a networ" technician at !est.ing) Inc. 8ou ha+e
subnetted the (:1.1:5.17.: networ" with a @(3 mas". Cow many
usable subnetwor"s and usable host addresses per subnet will be
pro+ided?
. , networ"s with 3, hosts
#. 3, networ"s and , hosts
$. ( networ"s and 3( hosts
D. 3( networ"s and ( hosts
%. 3 networ" and 7: hosts
nswer' $
,7. 8ou are a networ" technician at !est.ing) Inc. 8our !est.ing
trainee is studying the spanning tree algorithm and wants to "now
what the default mechanism for determining the spanning=tree path
cost is. What would your reply be?
. Statically determined by the administrator.
#. Sum of the costs based on bandwidth.
$. !otal hop count.
D. Sum of the cost based on latency.
nswer' #
,5. 8ou are a networ" technician at !est.ing) Inc. 8ou are
re;uired to establish a !elnet session with a cisco router.
Which of the following commands should you use?
. test"ing10config1< line console :
test"ing10config=if1< enable password test"ing
#. test"ing10config1< line +ty :
test"ing10config=line1< enable password test"ing
$. test"ing10config1< line +ty :
test"ing10config=line1< enable secret test"ing
test"ing10config=line1< login
D. test"ing10config1< line console :
test"ing10config=line1< enable secret test"ing
test"ing10config=line1< login
%. test"ing10config1< line console :
test"ing10config=line1< password test"ing
test"ing10config=line1< login
F. test"ing10config1< line +ty :
test"ing10config=line1< password test"ing
test"ing10config=line1< login
nswer' F
,2. 8ou are a networ" technician at !est.ing) Inc. 8ou are
planning a networ" installation for the company.
!he design re;uires 1:: separate subnetwor"s) resulting in the
ac;uisition of a $lass # networ" address. Which of the following
subnet mas"s will pro+ide the 1:: subnetwor"s re;uired) if 5::
usable host addresses are re;uired per subnet?
. (55.(55.:.:
#. (55.(55.((,.:
$. (55.(55.(5,.:
D. (55.(55.(55.:
%. (55.(55.(55.((,
F. (55.(55.(55.(5,
nswer' $
,4. What is the function of access control lists 0$9s1? 0$hoose
7.1
. Gonitor the number of bytes and pac"ets.
#. ssume role off +irus detector.
$. Identify interesting traffic for DD*.
D. IP route filtering.
%. Pro+ide high networ" a+ailability.
F. $lassify and organiJing networ" traffic.
nswer' $)D)F
,6. What could you use to pre+ent rooting loops in the networ"
when configuring the networ" using a distance +ector routing
protocol? 0$hoose (.1
. Spanning !ree Protocol
#. Shortest path first tree
$. 9in"=state ad+ertisements 09S1
D. Cold=down timers
%. Split horiJon
F. D*P
nswer' D)%
5:. !he following e-hibit shows the router topology for the
!est.ing networ".
ll routers are running *IP. Which of the following statements
describe how the routers e-change their routing tables? 0$hoose
(.1
. !est.ing, e-changes with !est.ing7.
#. !est.ing, e-changes with !est.ing(.
$. !est.ing, e-changes with !est.ing1.
D. !est.ing1 e-changes with !est.ing7.
%. !est.ing1 e-changes with !est.ing(.
F. !est.ing1 e-changes with !est.ing,.
nswer' )D
51. Which of the following encapsulations can be used when
configuring a serial interface on a $isco router? 0$hoose 7.1
. !o"en *ing
#. %thernet
$. CD9$
D. PPP
%. Frame *elay
F. $CP
nswer' $)D)%
5(. 8ou are a networ" technician at !est.ing. !est.ing has a
class $ networ" license. !he company re;uires 5 usable subnets.
%ach subnet must accommodate at least 14 hosts.
Which networ" mas" should you use?
. ((5.((5.((,.:.
#. ((5.((5.(,:.:.
$. ((5.((5.(55.:.
D. (55.(55.(55.((,
%. ((5.((5.(55.(,:
nswer' D
57. 8ou are a networ" technician at !est.ing) Inc. !he !est.ing
networ" topology is shown in the following e-hibit'
%ach host is connected through its own 1:Gbps half=duple- switch
port to the e: interface of the router !est.ing1. What is the
bandwidth a+ailable to each host?
. 1 Gbps
#. 1: Gbps
$. (: Gbps
D. 1:: Gbps
%. 1(: Gbps
nswer' #
55. 8ou are a networ" technician at !est.ing) Inc. 8ou ha+e
completed the password reco+ery procedure on a $isco router
successfully and the router returned to normal operation.
What is configuration register +alue at this point in time?
. :-(11(
#. :-(1:,
$. :-(1:(
D. :-(1:1
%. :-(1::
nswer' $
53. 8ou are a networ" technician at !est.ing) Inc. 8ou are using
a switch to brea" up a broadcast domain. Which features of the
switch enables this?
. !ransparent bridging
#. $ut=through bridges
$. Fragment=free switches
D. Gicrosegmentation
%. Dirtual 9/s
F. Store=and=forward switching
nswer' %
52. !o upgrade a networ") emphasis must be placed on efficiency
and error=free transport rather than fast transport. For this
purpose) new switches had been purchased. Which switching mode
should be configured on these new switches to ha+e the desired
effect?
. 4:(.1; forwarding
#. D!P transparent mode
$. cut=through
D. store=and=forward
%. fragment=free
F. frame=filtering
nswer' D
54. Which of the following addresses can be assigned to networ"
hosts when gi+en a subnet mas" of (55.(55.(55.((,? 0$hoose 7.1
. 15.(7,.114.37
#. 6(.11.124.67
$. 17,.124.14.53
D. 16(.134.13.42
%. (:1.,5.113.156
F. (12.37.1(.16(
nswer' #)$)D
56. Documenting the name of the IOS image file of each router in
the networ" is part of updating networ" documentation.
Which of the following commands can be used to obtain this
information?
. *outer< show IOS
#. *outer< show +ersion
$. *outer< show image
D. *outer< show protocols
%. *outer< show flash
nswer' #
3:. Which of the following statements describes the rule of split
horiJon?
. Only routers can split boundaries 0horiJons1 between
concentric networ"s.
#. %ach S must "eep routing tables con+erged to pre+ent dead
routes from being ad+ertised across boundaries.
$. /etwor"s can only remain fully con+erged if all information is
sent out all acti+e interfaces.
D. Information about a route should not be sent bac" in the
direction from which the original update came.
%. Distance +ector protocols need fall bac" routers that are
responsible for momentary loops.
nswer' D
37. 8ou are a networ" technician at !est.ing) Inc. 8ou are
troubleshooting a connecti+ity problem. 8ou issue the ping
command during a router console session. 8our trainee wants to
"now what the ping command use to test connecti+ity between the
two de+ices.
What would your reply be?
. I$GP echo re;uest
#. Information interrupt re;uest
$. !imestamp reply
D. Source ;uench
nswer'
3,. 8ou are a networ" technician at !est.ing) Inc. 8ou must
assign static IP addresses to the ser+ers in the !est.ing
networ". For networ" 16(.134.(:.(,@(6 the router is assigned the
first usable host address while the sales ser+er is gi+en the
last usable host address.
Which of the following should be entered into the IP properties
bo- for the sales ser+er?
. IP address' 16(.134.(:.1, Subnet Gas"' (55.(55.(55.(,4 Default
&ateway' 16(.134.(:.6
#. IP address' 16(.134.(:.(5, Subnet Gas"' (55.(55.(55.: Default
&ateway' 16(.134.(:.1
$. IP address' 16(.134.(:.7: Subnet Gas" (55.(55.(55.(,4 Default
&ateway' 16(.134.(:.(5
D. IP address' 16(.134.(:.7: Subnet Gas" (55.(55.(55.(,: Default
&ateway' 16(.134.(:.12
%. IP address' 16(.134.(:.7: Subnet Gas" (55.(55.(55.(,: Default
&ateway' 16(.134.(:.(5
nswer' $
35. Which of the following statements regarding the store and
forward switching method are true? 0Select two options.1
. 9atency fluctuates regardless of frame siJe.
#. !he switch recei+es the complete frame before beginning to
forward it.
$. 9atency through the switch +aries with frame length.
D. !he switch chec"s the destination address upon receipt of
headers.
nswer' #)$
34. Which of the following statements are characteristic of a
typical D9/ arrangement? 0$hoose 7.1
. D9/s logically di+ide a switch into multiple) independent
switches at 9ayer (.
#. !run" lin"s can carry traffic for multiple D9/s.
$. D9/ implementation significantly increases traffic due to
adding trun"ing information.
D. D9/ can span multiple switches.
%. D9/s e-tend the collision domain to include multiple
switches.
F. D9/s typically decrease the number of multiple switches.
nswer' )#)D
21. 8ou are the networ" administrator at !est.ing) Inc.
!est.ingEs networ" topology is shown in the following e-hibit'
8ou can telnet to all of the routers. n employee named !ess has
mo+ed office and finds herself on a different floor. 8ou need the
address of Switch !est.ing5 to +erify that the employee who mo+ed
office remains in the same D9/.
What can you do to determine the IP address of !est.ing5?
. Issue the show ip route command on *outer !est.ing1.
#. Issue the show cdp neighbors detail command on *outer
!est.ing(.
$. Issue the show arp command on *outer !est.ing7.
D. Issue the show cdp neighbors detail command on *outer
!est.ing7.
%. Issue the show arp command on *outer !est.ing1.
F. Issue the show ip route command on *outer !est.ing(.
nswer' D
2(. 8ou are a networ" technician at !est.ing) Inc. !he !est.ing
networ" is shown in the following e-hibit'
8ou must configure the address on the !est.ing( serial interface.
Which of the following commands will you use?
. !%S!.I/&(0config=if1< ip address 12(.13.12.1 (55.(55.(55.:
#. !%S!.I/&(0config=if1< ip address 12(.13.14.( (55.(55.(5(.:
$. !%S!.I/&(0config=if1< ip address 12(.13.12.( (55.(55.(55.(5(
D. !%S!.I/&(0config=if1< ip address 12(.13.13.: (55.(55.(55.:
nswer' #
2,. 8ou are a networ" technician at !est.ing) Inc. 8ou add a new
wor"station to the !est.ing networ" to accommodate a new
employee. !he rele+ant section of the !est.ing networ" is shown
in the following e-hibit'
!he employee is unable to connect to the ser+er !est.ing at IP
address 16(.134.1:.64@(2.
$an you identify the incorrectly configured networ" parameter in
the wor"station configuration?
. IP address of the %thernet : router interface
#. Ser+er
$. Wor"station default gateway
D. Wor"station subnet mas"
%. Wor"station IP address
nswer' $
25. 8ou are a networ" technician at !est.ing. 8our trainee as"s
you what 11111::: binary is in decimal.What would your reply be?
. ((:
#. ((,
$. (,:
D. (,4
%. (53
nswer' D
23. 8ou are a networ" technician at !est.ing) Inc. 8ou recei+ed a
report that users on the 12(.12.((.: networ" are unable to reach
the ser+er located on the 12(.71.5.: networ". 8ou connected to
router.
!est.ing1 +ia the console port) issued the show ip route command)
and could ping the ser+er.
!he networ" topology and the output from the show ip route is
shown in the following e-hibit'
What is the cause of this problem?
. !he Fast%thernet interface is disabled.
#. !he neighbor relationship table is not updated.
$. static route is configured incorrectly.
D. !he routing table on !est.ing1 is not updated.
%. IP routing is not enabled.
nswer' $
22. 8ou are a networ" technician at !est.ing) Inc. !he router
topology for the !est.ing networ" is shown in the following
e-hibit'
!est.ing( and !est.ing7 are configured for *IP+1 and ha+e
complete connecti+ity. !est.ing1 was
recently added to the networ". 8ou want !est.ing1 to ha+e full
connecti+ity as well.
What would then be the most appropriate !est.ing1 configuration?
. !est.ing10config1< router rip
!est.ing10config=router1< networ" 1:.:.:.:
!est.ing10config=router1< networ" 12(.13.:.:
!est.ing10config=router1< networ" 16(.134.1.:
#. !est.ing10config1< router rip
!est.ing10config=router1< networ" 1:.:.:.:
!est.ing10config=router1< networ" 16(.134.1.:
$. !est.ing10config1< router rip
!est.ing10config=router1< networ" 1:.:.:.:
!est.ing10config=router1< networ" 12(.13.:.:
D. !est.ing10config1< router rip
!est.ing10config=router1< networ" 1:.:.:.:
nswer' $
24. 8ou are a networ" technician at !est.ing) Inc. 8ou are
re;uired to troubleshoot a networ" connecti+ity problem. While
busy) you obser+e steady lin" lights on both the wor"station /I$
and the switch port to which the wor"station is connected.
Cowe+er) when the ping command is issued from the wor"station)
the output message K*e;uest timed outL is displayed.
t which layer of the OSI model does this problem reside?
. !he data lin" layer
#. !he application layer
$. !he access layer
D. !he session layer
%. !he networ" layer
nswer' %
26. !he !est"ing networ" is shown in the following e-hibit'
What is the function of the Frame *elay D9$I with regard to
!est.ing1?
. Defines the signaling standard between !est.ing1 and
!est.ing(.
#. $lassifies the encapsulation used between !est.ing1 and
!est.ing(.
$. Identifies the circuit between !est.ing1 and the frame switch.
D. $lassifies the circuit between !est.ing1 and !est.ing(.
%. Defines the signaling standard between !est.ing1 and the frame
switch.
nswer' $
4:. 8ou are a networ" technician at !est.ing) Inc. !he router
topology for the !est.ing networ" is shown in the following
e-hibit'
!est.ing is communicating with the ser+er.
What will be the source G$ address of the frames that !est.ing
recei+es from the ser+er?
. !he G$ address of router interface e:.
#. !he G$ address of router interface e1.
$. !he G$ address of !est.ing.
D. !he G$ address of the ser+er networ" interface.
nswer'
4(. What will be the calculated OSPF cost of an OSPF interface
that has been configured with the bandwidth 3, command?
. 1
#. 1:
$. 3,
D. 153(
%. 3,:::
F. 1(4:::
nswer' D
47. 8ou are a networ" technician at !est.ing) Inc. newly
appointed trainee wants to "now what the purpose of D9$Is in
Frame *elay is.
What would your response be?
. !hey determine the encapsulation type employed by the Frame
*elay.
#. !hey identify the logical circuit between a local router and a
Frame *elay W/ switch.
$. !hey represent the physical address of the router.
D. !hey represent the "eepali+es in the maintenance of PD$.
nswer' #
4,. Which of the following statements is true regarding the
command se;uence illustrated below? 0$hoose 7.1
!est.ing0config1< interface loopbac" :
!est.ing0config=if1< ip address 16(.134.13.(, (55.(55.(55.(55
. It creates a +irtual) software only) interface.
#. It pro+ides a way to test the con+ergence of OSPF routing
updates.
$. !he mas" of (55.(55.(55.(55 is called a host mas".
D. It uses a wildcard mas" of (55.(55.(55.(55.
%. It ensures that an interface is always acti+e for OSPF
processes.
F. !hese commands can only be issued to configure serial
interfaces.
nswer' )$)%
43. Which of the statements mentioned below describes the OSPF
routing protocol? 0$hoose 7.1
. It confines networ" instability to a single area of networ".
#. It increases the routing o+erhead of the networ"
$. It supports D9SG
D. It routes between utonomous Systems.
%. It allows e-tensi+e control of routing update
nswer' )$)%
42. Which field of frame id used by error detection schemes when
chec"ing on errors?
. G!B
#. PDB
$. F$S
D. Flag
%. G$
F. #*I
nswer' $
44. What are the options for Frame 9GI types. 0$hoose 7.1
. I.671
#. I%%%
$. $isco
D. I%!F
%. I677a
F. /SI
nswer' $)%)F
46. Which of the following addresses can be assigned to networ"
hosts when gi+en a subnet mas" of
(55.(55.(55.((,? 0Select three options.1
. (:1.,5.113.156
#. 17,.124.14.3(
$. 16(.134.13.61
D. 6(.11.124.67
%. (12.37.1(. 71
F. 15.(7,.114.37
nswer' #)$)D
6:. Which of the following commands will pro+ide you with
information regarding the 9ayer 7 configuration of directly
connected router interfaces?
. show ip lin"s
#. show cdp neighbors
$. show cdp neighbors detail
D. show ip clients
%. show ip route
nswer' $
61. 8ou are the networ" administrator at !est.ing Inc. !he
!est.ing networ" is shown in the following e-hibit'
Costs in the !est.ing sales department cannot get access to a new
ser+er at the #ranch Office. $onsider the IP addressing scheme in
the e-hibit to determine the problem.
. !he default gateway in the sales department is inaccurate.
#. !he serial : interface on the Gain Office router and the
serial 1 interface on the #ranch Office router are not
compatible.
$. !he subnet mas" of the wor"stations in the sales department is
inaccurate.
D. !he host address of the ser+er at the #ranch Office is
in+alid.
%. !he default gateway of the ser+er at the #ranch Office is
inaccurate.
nswer' D
6(. 8ou are a networ" technician at !est.ing) Inc. !est.ing has a
$lass # networ" with a subnet mas" of (55.(55.(55.:.
Which of the following statements is true regarding this networ"?
0$hoose (.1
. !here are (5, usable subnets.
#. !here are (53 usable hosts per subnet.
$. !here are 5: usable subnets.
D. !here are (5, usable hosts per subnet.
%. !here are (, usable hosts per subnet.
F. !here is one usable networ".
nswer' )D
67. 8ou are a networ" technician at !est.ing) Inc. 8ou ha+e been
as"ed to set up Frame *elay for point=topoint subinterfaces.
Which of the following should not be configured?
. !he local D9$I on each subinterface of the Frame *elay.
#. !he Frame *elay encapsulation on the physical interface.
$. n IP address on the physical interface.
D. !he subinterface only.
nswer' $
6,. !he following access list was applied outbound on the %:
interface connected to the 16(.134.1.4@(6 9/'
access=list 1(7 deny tcp 16(.134.1.4 :.:.:.2 e; (: any
access=list 1(7 deny tcp 16(.134.1.4 :.:.:.2 e; (1 any
What effect will this particular access list ha+e on traffic?
. F!P traffic from 16(.134.1.(( will be denied.
#. /o traffic) e-cept for F!P traffic will be allowed to e-it %:.
$. F!P traffic from 16(.134.1.6 to any host will be denied.
D. ll traffic e-iting %: will be denied.
%. ll F!P traffic to networ" 16(.134.1.6@(6 will be denied.
nswer' D
65. 8ou are a networ" technician at !est.ing) Inc. 8our trainee
wants to "now which command is used to display the placement and
direction of an IP access control list on a router.
What would your response be??
. show interface list
#. show ip route
$. show ip interface
D. show ip interface brief
%. show interface
nswer' $
63. 8ou are a networ" technician at !est.ing) Inc. 8our trainee
wants to "now what the characteristics of microsegmentation are.
What would your response be?? 0Select two options.1
. Dedicated paths between sending and recei+ing hosts are
established.
#. Gultiple subnetwor" broadcast addresses are created.
$. Gultiple *P tables are needed.
D. !he decrease in the number of collision domains.
%. #roadcast domains are enhanced.
F. #andwidth is dedicated to connect hosts.
nswer' )F
64. Why is a Spanning=!ree algorithm used in a switched 9/?
. !o pro+ide a monitoring mechanism for networ"s in switched
en+ironments.
#. !o manage D9/s across multiple switches.
$. !o pre+ent switching loops in networ"s with redundant switched
paths.
D. !o segment a networ" into multiple collision domains.
%. !o pre+ent routing loops in networ"s.
nswer' $
66. 8ou are a networ" technician at !est.ing) Inc. One of your
trainees as"ed you which parameter must be supplied when
initialiJing the I&*P routing process.
What would your response be?
. IP address subnet mas"
#. Getric weighting
$. *egister administrati+e id
D. utonomous system number
%. $onnected networ" ID numbers
nswer' D
1::. 8ou wor" as a technician at !est.ing. 8ou are as"ed to add a
new D9/) named $$OB/!S) to your switched networ".
Which of the following are true regarding configuration of this
D9/? 0Select three options.1
. !he D9/ must be created.
#. !he desired ports must be added to the new D9/.
$. !he D9/ must be added to the all of the domains.
D. !he D9/ must be named.
%. n IP address must be configured for all the $$OB/!S D9/.
nswer' )#)D
1:1. 8ou are a networ" technician at !est.ing) Inc. 8our newly
appointed trainee wants to segment a networ". What de+ices would
you ad+ice him? 0$hoose 7.1
. Bse switch and hub con+erters.
#. Bse media con+erters.
$. Bse switches.
D. Bse routers.
%. Bse bridges.
F. Bse repeaters.
nswer' $)D)%
1:(. 8ou are a networ" technician at !est.ing) Inc. 8ou ha+e been
assigned a Funior trainee named %llen. She wants you to describe
what is specific for a global command.
What would your response be?
. command that is a+ailable in e+ery release of IOS)
regardless of the +ersion or deployment status.
#. command that is set once and will result in affecting the
rest of the router operationability.
$. command that is implemented in all IOS +ersions.
D. command that is uni+ersal in application supporting
different types of protocols.
%. command that can be entered in any configuration mode.
nswer' #
1:7. 8ou are a networ" technician at !est.ing) Inc. 8our trainee
wants to "now which of the following is the range of binary
+alues for the first octet in $lass # addresses.
What would your response be?
. 1:::::::=111:1111
#. 11::::::=111:1111
$. 1:::::::=1:111111
D. 1:::::::=11111111
%. 11::::::=1:111111
nswer' $
1:,. Which of the following access list statements will deny all
telnet connections to subnet 1:.1:.1.:@(,?
. access=list 15 deny telnet any 1:.1:.1.: :.:.:.(55 e; (7
#. access=list 115 deny udp any 1:.1:.1.: e; telnet
$. access=list 15 deny tcp 1:.1:.1.: (55.(55.(55.: e; telnet
D. access=list 115 deny tcp any 1:.1:.1.: :.:.:.(55 e; (7
%. access=list 15 deny udp any 1:.1:.1.: (55.(55.(55.: e; (7
nswer' D
1:5. 8ou are a networ" technician at !est.ing. 8our newly
appointed trainee wants to "now why the
Spanning=!ree algorithm is used in a switched 9/.
What would your response be?
. !o manage D9/s across multiple switches.
#. !o pro+ide a mechanism for networ" monitoring in switched
en+ironments.
$. !o pre+ent switching loops in networ"s with redundant switched
paths.
D. !o segment a networ" into multiple collision domains.
%. !o pre+ent routing loops in networ"s.
nswer' $
1:2. Which protocol allows the configuring of a new D9/ to be
distributed to all the switches in a domain in
a switch networ"?
. S!P
#. D!P
$. %&*P
D. S/GP
%. DC$P
nswer' #
1:6. Cow would you respond when as"ed which of the following are
D9/ frame encapsulation types that may be configured on a
catalyst switch? 0$hoose (1
. D!P
#. 4:(.1I
$. 99$
D. IS9
%. $DP
F. $CP
nswer' #)D
11:. Which of the following commands will configure an interface
on a $atalyst (6:: series switch to carry traffic from all D9/s
to another directly connected switch? 0What would your response
be?1
. Switch0config=if1< +lan all
#. Switch0config=if1< switchport trun" encapsulation dot1;
$. Switch0config=if1< switchport access +lan all
D. Switch0config=if1< switchport mode trun"
%. Switch0config=if1< switchport access clan 7:
nswer' D
111. Why is it a wise decision to use a hierarchical design on
OSPF networ"s? 0$hoose 7.1
. !o reduce the comple-ity of router configuration
#. !o speed up con+ergence
$. !o confine networ" instability to single areas of the networ"
D. !o reduce routing o+erhead
%. !o lower costs by replacing routers
F. !o decrease latency by increasing bandwidth
nswer' #)$)D
11(. 8ou are a networ" technician at !est.ing) Inc. 8ou ha+e been
as"ed to add a new router into an established OSPF networ". !he
!est.ing networ"s attached to the new router do not appear in the
routing tables of the other OSPF routers. &i+en the information
in the partial configuration shown below) what configuration
error is causing this problem?
*outer0config1< router ospf 1
*outer0config=router1< networ" 1:.1:.1:.: (55.:.:.: area :
. !he S is not correctly configured
#. !he networ" subnet mas" is incorrectly configured
$. !he networ" wildcard mas" is configured incorrectly
D. !he networ" number is not correctly configured
%. !he process id is configured incorrectly
nswer' $
117. 8ou are a networ" technician at !est.ing) Inc. 8ou need to
configure a router to run OSPF and to add networ" 16(.134.1:.:@(,
to OSPF area :.
Which of the following commands do you need to achie+e this?
0$hoose (.1
. *outer0config=router1< networ" 16(.134.1:.: :.:.:.(55 :
#. *outer0config=router1< networ" 16(.134.1:.: :.:.:.(55 area :
$. *outer0config=router1< networ" 16(.134.1:.: (55.(55.(55.: area
:
D. *outer0config1< router ospf :
%. *outer0config1< router ospf 1
F. *outer0config1< router ospf area :
. It can be specified as either a decimal +alue or as an IP
address. If you intend to associate areas with IP subnets) you
can specify a subnet address as the area=id.
nswer' #)%
11,. 8ou are a networ" technician at !est.ing) Inc. !he !est.ing
%ngineering Department 9/ is recei+ing obsolete information from
the !est.ing #usiness DepartmentEs networ" traffic broadcasting.
8ou need to contain this traffic within the #usiness Department)
but at the same time also maintain connecti+ity with enterprise
ser+ices and the Internet.
Cow will you achie+e this? 0$hoose (.1
. Bse half and full=duple- %thernet on the %ngineering
Department 9/
#. %stablish a D!P domain to minimiJe the obsolete traffic
$. $hange the switch IP address to a normal address
D. $reate separate D9/s and subnets for the two departments and
route between the two
%. Pro+ide greater bandwidth to the %ngineering Department 9/
F. Place the business department on a separate subnet and route
between networ"s
nswer' D)F
115. OSPF routing ma"es use of areas. What are the
characteristics of these areas? 0$hoose 7.1
. Cierarchical OSPF networ"s do not need multiple areas
#. Gultiple OSPF areas must connect to area :
$. Single area OSPF networ"s must be configured in area 1
D. reas can be assigned any number from : to 37575
%. rea : is called the bac"bone area
F. %ach OSPF area need to be configured with a loopbac" interface
nswer' #)D)%
113. 8ou are a networ" technician at !est.ing. newly appointed
trainee wants to "now how the spanningtree path cost is
determined by default.
What would your response be?
. It is the indi+idual lin" cost based on latency
#. It is the sum of the costs based on bandwidth
$. It is the total hop count
D. It is dynamically determined based on load
nswer' #
112. 8ou are a networ" technician at !est.ing) Inc. 8ou are
installing a new wor"station to the !est.ing networ". !he
rele+ant networ" segment is shown in the following e-hibit'
What should be the IP address of the host?
. 16(.134.5.55
#. 16(.134.5.,2
$. 16(.134.5.,:
D. 16(.134.5.7(
%. 16(.134.5.1,
nswer' $
114. If pressed for time) how would you go about ;uic"ly
configuring a router for basic operations?
. *OG Gonitor mode
#. S%!BP mode
$. utoflash mode
D. *M#OO! mode
nswer' #
116. $haracteristic such as c"nowledgements) se;uencing) and
flow control are typical of which OSI layer?
. 9ayer (
#. 9ayer 7
$. 9ayer ,
D. 9ayer 5
%. 9ayer 3
F. 9ayer 2
nswer' $
1(1. Study the %-hibit below carefully'
$onsider the following scenario' 8ou are consoled into the Peanut
router and is able to ping Serial: end %thernet: ports of the
Popcorn router. Cowe+er) you cannot ping its %thernet1 interface.
&i+en the e-hibit abo+e and the command output) can you identify
the possible causes for this problem? 0Select two options.1
. !he Popcorn router is not forwarding *IP updates.
#. !he Popcorn router did not include networ" 16(.134.1(.: in its
routing configuration.
$. !he %thernet1 interface of the Popcorn router is shutdown.
D. !he cloc"rate is not present in the configuration of one of
the routers.
%. !he Serial interface of the Popcorn router is not
operationable.
nswer' #)$
1((. Study the %-hibit below carefully'
*tr<debug ip rip
*ip protocol debugging is on
*tr<
1d:5h' *IP' sending +1 update to (55.(55.(55.(55 +ia
Fast%thernet:@: 012(.13.1.11
1d:5h' *IP' build update entries
1d:5h' networ" 1:.:.:.: metric 1
1d:5h' networ" 16(.134.1.: metric (
1d:5h' *IP' sending +1 update to (55.(55.(55.(55 +ia Serial:@:
01:.:.4.11
1d:5h' *IP' build update entries
1d:5h' networ" 12(.13.:.: metric 1
*tr<
1d:5h' *IP' recei+ed +1 update from 1:.:.15.( on Serial:@:
1d:5h' 16(.134.1.: in 1 hops
1d:5h' 16(.134.: in 13 hops 0inaccessible1
Which of the following statements would be true when one
encounters the command output shown in the
display? 0Select two options.1
. ping to 1:.:.15.( will be successful.
#. *tr has three interfaces that will ta"e part in the *IP
process.
$. !here are at least two routers participating in the *IP
process.
D. ping to 16(.134.134.( will be positi+e.
nswer' )$
1(7. Which of the following is the binary e;ui+alent of the
decimal number (71?
. 11:11:11
#. 1111::11
$. 111::111
D. 11111::1
%. 11:1::11
nswer' $
1(,. Which of the following %I&*P route entries would be
described as a feasible successor?
. primary route) stored in the routing table
#. bac"up route) stored in the routing table
$. bac"up route) stored in the topology table
D. primary route) stored in the topology table
nswer' $
1(5. What ad+antages does full=duple- %thernet ha+e o+er single=
duple-? 0Select two options.1
. Bses ine-pensi+e hubs
#. Operates without collisions
$. Operates on switches
D. Pro+ides faster data transfer
%. BtiliJes fewer wiring pairs
nswer' #)D
1(3. In a routine chec" on the state of the networ") you disco+er
that the e-isting copy of the $isco IOS is outdated and needs to
be updated.
Which of the following commands would you issue to replace the
$isco router IOS with the newer
+ersion?
. *outer< copy tftp flash
#. *outer< copy flash run
$. *outer0config1< restore flash
D. *outer0config1< repair flash
%. *outerN copy start flash
F. *outer< copy start flash
nswer'
1(2. 8our trainee wants to "now which of the following is a 9ayer
( protocol used to maintain a loop=free networ". What will you
tell her?
. *IP
#. S!P
$. D/P
D. $DP
%. D!P
nswer' #
1(6. 8ou want to form a W/ connection between two routers) one
is a $isco router and the other from another manufacturer) that
are directly connected +ia a serial lin". Which of the following
commands can you use?
. 9ab0config=if1< encapsulation hdlc ansi
#. 9ab0config=if1< encapsulation ppp
$. 9ab0config=if1< encapsulation isdn
D. 9ab0config=if1< encapsulation frame=relay default
nswer' #
17:. Which of the following addresses is representati+e of a
unicast address?
. 12(.71.1(4.(55@14
#. (55.(55.(55.(55
$. 16(.134.(,.56@7:
D. FFFF.FFFF.FFFF
%. ((,.1.5.(
nswer'
171. Which of the following are features of the routing protocol
%I&*P? 0Select two options.1
. Cas a ma-imum hop count of (5
#. $an differentiate between internal and e-ternal routes
$. Bses a 7(=bit metric
D. $an maintain only one routing table
%. /eed all networ"s to use the same subnet mas"
F. Supports only one routed protocol
nswer' #)$
17(. Which of the different types of pac"ets mentioned below is
sent by routers running OSPF to maintain connecti+ity with
neighboring routers?
. OSP pac"ets
#. hello pac"ets
$. "eepali+e pac"ets
D. dead inter+al pac"ets
%. 9SB pac"ets
nswer' #
177. 8our !est.ing.com trainee Sandra wants to "now what
information a router runs through a lin"=state protocol to build
and maintain its topological database. What can you tell her?
0Select two options.1
. 9Ss from other routers
#. #eacons recei+ed on point=to=point lin"s
$. hello pac"ets
D. *outing tables recei+ed from other routers
%. SP pac"ets sent by other routers
F. !!9 pac"ets from e-clusi+e routers
nswer' )$
17,. Which type of /! will map multiple pri+ate IP addresses to
a singular registered IP address through ma"ing use of different
ports?
. static /!
#. port loading
$. o+erloading
D. dynamic /!
nswer' $
175. In which D!P mode should a catalyst switch be to be able to
delete and add D9/s to a management domain?
. !ransparent
#. Ser+er
$. Domains
D. $lient
%. Bsers.
nswer' #
176. When dealing with point=to=point networ"s) which address are
OSPF hello pac"ets addressed to?
. 1(2.:.:.1
#. 16(.134.:.5
$. ((7.:.:.1
D. 12(.13.:.1
%. ((,.:.:.5
F. (5,.(55.(55.(55.(55
nswer' %
1,:. Study the %-hibit below carefully'
Which of the following access lists will pre+ent !elnet traffic
from the &raphics Department from
reaching the C* ser+er attached to the %astfield router when
grouped with the e: interface in the
inbound direction on the Westfield router?
. deny tcp 16(.134.13.: :.:.:.(55 16(.134.12.(5( :.:.:.: e; (7
permit ip any any
#. permit ip any any
deny tcp 16(.134.13.: :.:.:.(55 16(.12(.(5( :.:.:.: e; (7
$. permit ip any any
deny tcp 16(.134.12.(5( :.:.:.: 16(.134.: :.:.:.(55 e; (7
D. deny tcp 16(.134.14.(3( :.:.:.: 16(.134.13.: :.:.:.(55 e; (7
permit ip any any
nswer'
1,(. $onsider the address 16(.134.15.16@(4) which of the
following addresses are +alid host addresses on this subnet?
0Select two options.1
. 16(.134.15.12
#. 16(.134.15.:
$. 16(.134.15.(6
D. 16(.134.15.13
%. 16(.134.15.71
nswer' )$
1,7. One of your trainees wants to "now which fields are common
to the !$P and the BDP segments. What can you tell her? 0Select
two options.1
. source address
#. options
$. se;uence number
D. sources
%. destination port
F. chec"sum
nswer' %)F
1,,. $ongestion on an %thernet networ" can be caused by one of
the following. Which one?
. Increasing the number of collision domains.
#. Gicrosegmenting the networ".
$. dding hubs for connecti+ity to the networ".
D. Putting additional switches in the networ".
%. Implementing D9/s in the networ".
nswer' $
1,5. Study the %-hibit below carefully'
fter considering the effects of the command output illustrated
in the e-hibit abo+e) which of the following are operational on
the serial lin"? 0Select two options.1
. $DP
#. IP
$. $ompression
D. IPM
%. Gultilin"
F. !M
nswer' )#
1,3. Study the %-hibit below carefully'
Bsers on the Colyo"e router cannot get access to the intranet
ser+er attached to interface %: of the $hicopee router. fter
in+estigating you disco+er that the routing table of the Colyo"e
router shows that an entry for the $hicopee %: networ" is
missing.
Which command) according to the abo+e e-hibit) will configure the
Colyo"e router with a path to the intranet ser+er networ"?
. Colyo"e0config1< ip host $hicopee (:1.27.1(2.(
#. Colyo"e0config1< ip networ" (:(.14.74.:
$. Colyo"e0config1< ip networ" (:(.14.14.: (55.(55.(55.:
D. Colyo"e0config1< ip host $hicopee (:1.27.1(2.: (55.(55.(55.:
%. Colyo"e0config1< ip route (:(.14.14.: (55.(55.(55.:
(:1.27.1(2.(
F. Colyo"e0config1< ip route (:1.27.1(2.( (55.(55.(55.:
(:(.14.14.:
nswer' %
1,2. Study the %-hibit below carefully'
fter considering the partial outputs displayed in the e-hibit
abo+e) which switch de+ice would be the spanning tree root bridge
for a networ" of only these four de+ices?
. Giami
#. 9ondon
$. !ampa
D. $airo
nswer' D
1,4. One of your trainees wants to "now at what stage are pac"ets
processed by an inbound access list. What can you tell her?
. #efore they are routed to an outbound interface.
#. fter they are routed for outbound traffic.
$. fter they are routed to an outbound interface while ;ueuing.
D. #efore and after they are routed to an outbound interface.
nswer'
1,6. One of your trainees wants to "now what the calculated OSPF
cost of the lin" will be if the interface has been configured
with the bandwidth 3, command. What will you tell her?
. 1(4:::
#. 3,:::
$. 154(
D. 1:
%. 1
nswer' $
15:. Which of the following fields are contained within an I%%%
%thernet frame header?
. source and destination G$ address
#. source G$ address and destination networ" address only
$. source and destination networ" address only
D. source networ" address and destination G$ address
%. source and destination G$ address and source and destination
networ" address
nswer'
151. Study the %-hibit below carefully'
!wo switches named 9ondon and Gadrid has been configured to use
D!P. #ut they are not sharing D!P
messages. *eferring to the command output in the e-hibit abo+e)
why is this so?
. D!P D( mode is not in operation.
#. D!P pruning mode is disabled.
$. !he D!P domain name is configured incorrectly.
D. !he D!P operating mode is not configured.
%. !he D!P +ersion is configured incorrectly.
nswer' $
15(. One of your trainees as"ed you which parameter must be
supplied when initialiJing the I&*P routing process. What is your
response?
. $onnected subnet numbers
#. *egister administrati+e subnet mas"s
$. IP address mas"
D. utonomous system number
%. Getric weights
nswer' D
157. Which of the following de+ices can you use to segment a
networ"? 0Select three options.1
. hub
#. repeater
$. bridge
D. switch
%. router
nswer' $)D)%
15,. 8ou are a technician at !est.ing. fter configuring your
router) you find that you cannot ping the directly connected
serial port of the neighboring router. !he show running=config
output displays the word KshutdownL for the serial interface.
Which of the following lines will be displayed in the show
interface s: output?
. Serial : is down) line protocol is down
#. Serial : is up) line protocol is down
$. Serial : is down) line protocol is up
D. Serial : is administrati+ely down) line protocol is down
%. Serial : is administrati+ely up) line protocol is down
F. Serial : is administrati+ely down) line protocol is up
nswer' D
155. Study the %-hibit below carefully'
Which data structure is described in the e-hibit abo+e?
. FDDI frame
#. %thernet frame
$. BDP datagram
D. !o"en *ing frame
%. !$P segment
nswer' %
152. What are the basic networ" ser+ices that is pro+ided by the
$isco IOS? 0Select three options.1
. Defines topology
#. ccess to networ" resources
$. *outing and switching functions
D. $reation of D9/s
%. Iuality of ser+ice
nswer' $)D)%
156. Which of the following pieces of information is displayed by
the show host command? 0Select two options.1
. !he IP addresses of wor"stations allowed gain access to the
router.
#. Permanent name=to=address mappings created using the ip host
command.
$. !emporary and permanent D/S entries.
D. !he names of the routers created using the hostname command.
%. !he length of time a host has been connected +ia !elnet.
nswer' #)$
13:. Study the %-hibit below carefully'
In the illustration) Cost !est.ing1 is trying to communicate with
Cost !est.ing(. !he e: interface on !est.ing$ is down.
Which of the following are true? 0Select two options.1
. !est.ing$ will ma"e use of I$GP to inform !est.ing 1)
!est.ing) and !est.ing# that Cost ( is
unreachable.
#. !est.ing$ will send a Destination Bnreachable message type.
$. !est.ing$ will ma"e use of I$GP to inform !est.ing 1 that
!est.ing ( is unreachable.
D. !est.ing$ will use I$GP to inform !est.ing# that !est.ing( is
unreachable.
%. !est.ing$ will issue a *outer Selection message type.
F. !est.ing$ will issue a Source Iuench message type.
nswer' #)$
131. Study the %-hibit below carefully'
!he company) !est.ing) networ" is running OSPF on the routers as
shown in the e-hibit abo+e. n
ISD/ lin" pro+ides connecti+ity to the remote sales office.
Which of the following route types should be configured on the
$orporate router to connect to the sales officeEs remote networ"
while minimiJing networ" o+erhead on the ISD/ lin"?
. *IP route
#. n OSPF route
$. static route
D. default route
%. dynamic route
nswer' $
13(. Study the %-hibit below carefully'
!he e-hibit abo+e shows the output from the router. Bse it to
determine which of the following are correct. 0Select two
options.1
. *outer Oohn will get routing updates on the Serial:@1
interface.
#. *outer Oohn will issue routing updates out the Serial:@:
interface.
$. *outer Oohn ma"es use of a lin"=state routing protocol.
D. *outer Oohn will get routing updates on the Serial:@:
interface.
%. *outer Oohn will issue routing updates out the Fast%thernet:@:
interface.
nswer' #)D
13,. Study the %-hibit below carefully'
new router has been installed in the branch office in 9isbon.
Cowe+er) the networ" administrator cannot ma"e a bac"up of the
IOS image of the new route to the !F!P ser+er located in the
&ibraltar office. Following the networ" diagram) can you identify
the cause of the problem?
. IP address if the !F!P ser+er not correct.
#. Incorrect subnet mas" of the !F!P ser+er.
$. Default gateway of the !F!P ser+er not properly set.
D. Subnet mas" on the 9isbon router not correct
%. Incorrect IP address configured on %: of the &ibraltar router
nswer' #
135. Study the %-hibit below carefully'
Bsing the information in the e-hibit abo+e) which of the
following command lines would configure the serial: port on the
!est.ing( router with the least usable host address in the
16(.(13.7(.7( subnet correctly?
. !est.ing(0config=if1< ip address 16(.(13.7(.37 (55.(55.(55.(,4
#. !est.ing(0config=if1< ip address 16(.(13.7(.74 (55.(55.(55.(,:
$. !est.ing(0config=if1< ip address 16(.(13.7(.76 (55.(55.(55.(,4
D. !est.ing(0config=if1< ip address 16(.(13.7(.37 (55.(55.(55.(,4
no shut
%. !est.ing(0config=if1< ip address 16(.(13.7(.76 (55.(55.(55.(,4
no shut
F. !est.ing(0config=if1< ip address 16(.(13.7(.74 (55.(55.(55.(,4
nswer' F
133. Study the %-hibit below carefully'
!o protect the records ser+er) a named access list called
records>bloc" has been employed to pre+ent student and Internet
access to the records. ll other users within the enterprise
should ha+e access to this ser+er. !his access list was applied
to the e: interface of the !est.ing7 router in the outbound
direction.
Which of the following conditions should the access list contain
to meet these re;uirements?
0Select two options.1
. permit 12(.13.3,.(5, :.:.:.: 12(.13.:.: :.:.(55.(55
#. permit 12(.13.:.: :.:.(55.(55 12(.13.3,.(5, :.:.:.:
$. deny 12(.13.3,.(5, :.:.:.: 12(.13.3(.: :.:.:.(55
D. deny 12(.13.3(.: :.:.:.(55 12(.13.3,.(5, :.:.:.:
%. deny 12(.13.3,.(5, :.:.:.: any
F. permit any any
nswer' #)D
132. Study the %-hibit below carefully'
Which of the following statements regarding the IP addresses as
illustrated in the e-hibit abo+e) are true? 0Select three
options.1
. ddress $ is a public $lass $ address.
#. ddress $ is an e-clusi+e $lass $ address.
$. ddress # is a public $lass # address.
D. ddress is a public $lass address.
%. ddress # is a pri+ate $lass # address.
F. ddress is an e-clusi+e $lass address.
nswer' )D)%
134. Study the %-hibit below carefully'
*outer< show running=config
Psome output te-t omittedN
interface serial:@:
bandwidth 3,
ip address 12(.13.1::.( (55.(55.:.:
encapsulation frame=relay
frame=relay map ip 12(.13.1::.1 (:: broadcast
!he Cong .ong office with *outer !est.ing1) has a communication
problem with the !o"yo branch
office which has *outer !est.ing(. !he scenario is the following'
*outer !est.ing1 is unable to reach *outer !est.ing(. #oth
routers are running IOS +ersion 1(.:.
fter re+iewing the command output and graphic) your boss wants
to "now what is the most probable
cause of the problem. What should you tell him?
. #andwidth configuration incorrect
#. IP address not correct
$. Improper map statement
D. Improper 9GI configuration
nswer' $
12:. Which of the following commands should you use if you were
as"ed to apply an access list on a +irtual terminal line of a
router?
. *outer!.0config=line1< access=class 1: in
#. *outer!.0config=if1< ip access=class (7 out
$. *outer!.0config=line1< access=list 15: in
D. *outer!.0config=if1< ip access=list 1(4 out
%. *outer!.0config=line1< access=group 15 out
F. *outer!.0config=if1< ip access=group 11: in
nswer'
121. On three different occasions an administrator configured a
router) and after testing the configuration sa+ed it to /D*G by
issuing the copy running=config startup=config command. fter
each successful sa+e the administrator issued the reload command.
Cowe+er) each time when the router restarted) it appeared to ha+e
the default blan" configuration.
What could be the cause of such results?
. !he /D*G is corrupted.
#. !he boot system commands were omitted in the configuration.
$. !he configuration register setting is incorrect.
D. !he upgraded configuration incompatible with the hardware
platform.
%. !he upgraded IOS incompatible with the hardware.
nswer' $
12(. One of your trainees wants to "now which of the following
statements regarding the command ip route 12(.13.7.:
(55.(55.(55.: 16(.134.(., are true. What can you tell her?
0Select two options.1
. !he default administrati+e distance is used.
#. !he command is used to establish a static route.
$. !he command is used to configure the routers.
D. !he command is used to establish a stub networ".
%. !he subnet mas" for the source address is (55.(55.(55.:
nswer' )#
127. Which of the following statements can you use to describe
the process identifier that is used to run OSPF on a router?
0Select two options.1
. It is needed to identify a uni;ue instance of an OSPF
database.
#. It is an optional parameter only necessary if multiple OSPF
processes are used.
$. It is locally significant.
D. It is globally insignificant
%. ll routers in the same OSPF area must ha+e the same process
ID to e-change routing information.
nswer' )$
12,. 8ou were told to bloc" all traffic from an entire subnet
with a standard access control list by your boss. What IP address
and wildcard mas" should you use in the access control list to
bloc" all hosts from the subnet on which the host
16(.134.13.,7@(4 resides?
. 16(.134.13.7( :.:.:.13
#. 16(.134.13.,7 :.:.:.(1(
$. 16(.134.13.: :.:.:.15
D. 16(.134.13.7( :.:.:.15
%. 16(.134.13.: :.:.:.71
F. 16(.134.13.13 :.:.:.71
nswer' D
125. Study the %-hibit below carefully'
8ou are the networ" administrator at !est.ing. !est.ing is using
multiple routing protocols according to the e-hibit. ssuming
that all networ"s that are connected are ad+ertised) there are no
redistribution of routes) and all other parameters are set to
default) which path do you thin" will !est.ing use to reach
!est.ingD?
. It will ta"e the route +ia !est.ing#.
#. It will ta"e the route +ia !est.ing$.
$. It will use the route with the highest metric.
D. It will load balance o+er both paths.
%. It will ta"e the shortest route
nswer' #
123. Study the %-hibit below carefully'
8ou are the networ" administrator in this scenario. !he e-hibit
illustrates a console session running on a router and you ha+e
connected your Windows wor"station directly to the router %: port
as well. Which of the following are among the re;uirements for
the copy flash tftp command to be successful?0Select three
options.1
. !F!P ser+er software must be acti+ated.
#. !F!P ser+er software must be running on the administratorQs
wor"station.
$. !here must be space in the flash memory of the router to
accommodate the file to be copied.
D. !he copy flash tftp command must be supplied the IP address of
the administratorQs wor"station.
%. !he administratorQs wor"station must be on the same subnet as
the router %: interface.
F. !he %thernet connection between the router and the
administratorQs wor"station must be +ia straight through cable.
nswer' #)D)%
122. Study the %-hibit below carefully'
8ou wor" as a networ" administrator at !est.ing) 8ou recei+ed
complaints from the !est.ing
employees that their Frame *elay connection to the corporate site
is +ery slow. 8ou ha+e a suspicion that the lin" is o+erloaded.
Which output +alue indicates to the local router that traffic is
sent to the corporate site is e-periencing congestion ta"ing into
account the partial output of the *outer< show frame relay p+c
command shown in the e-hibit?
. in D% pac"ets :
#. last time PD$ status changed ::'(5',:
$. in #%$/ pac"ets 16(
D. D9$I R 1::
%. in F%$/ pac"ets 1,2
nswer' $
124. Study the %-hibit below carefully'
. !his router was configure with the commands'
*tr0config1<router rip
*tr0config=router1< networ" 12(.13.:.:
*tr0config=router1< networ" 1:.:.:.:
#. !his router was configured with the commands'
*tr0config1< router rip
*tr0config=router1< networ" 16(.134.1.:
*tr0config=router1< networ" 1:.:.:.:
*tr0config=router1< networ" 16(.134.134.:
$. !his router was configured with the commands'
*tr0config1< router rip
*tr0config=router1< +ersion (
*tr0config=router1< networ" 12(.13.:.:
*tr0config=router1< networ" 1:.:.:.:
D. Split horiJon was disabled on this router.
%. /etwor" 16(.134.134.: will be displayed in the routing table.
F. /etwor" 1:.:.:.: will be displayed in the routing table.
nswer' )F
126. What can you tell the $%O of !est.ing.com about ad+antages
of using D9/s? 0Select three options.1
. D9/s allow access to networ" ser+ices based on department)
not physical location.
#. D9/s utiliJe pac"et filtering to enhance networ" security.
$. D9/s pro+ide a low=latency) high bandwidth internetwor"ing
alternati+e.
D. D9/s pro+ide a method of communication between IP addresses
in large networ"s.
%. D9/s establish broadcast domains in switched networ"s.
F. D9/s can greatly simplify adding) mo+ing) or changing hosts
on the networ".
nswer' )%)F
141. One of your trainees wants to "now what +alues are used to
elect the root bridge in a spanning treetopology. What can you
tell her? 0Select two options.1
. !he #PDB +ersion number
#. !he access layer bridge setting
$. !he #ridge ID
D. !he spanning=tree update number
%. !he bridge priority
F. !he D9/ number
nswer' $)%
14(. Which of the following are the routing protocols that are
capable of supporting a networ" that uses D9SG and route
summariJation? 0Select three options.1
. I&*P
#. %I&*P
$. *IP +1
D. *IP +(
%. OSPF
F. D!P
&. 9S
nswer' #)D)%
14,. 8ou are the networ" administrator. 8our aim is to support a
multi=protocol networ" that includes IP)pple!al" and IPM. Which
routing protocol can you use that will achie+e this aim?
. OSPF
#. %I&*P
$. *IP +(
D. I&*P
%. *IP +1
nswer' #
144. Which of the following fields of frame is used by detection
schemes to perform its function?
. %**
#. Flag
$. F$S
D. G!B
%. G$
F. PDB
nswer' $
146. 8our company has been assigned the following IP address for
its networ"' 166.1,1.(2.:
Of subnet mas" of (55.(55.(55.(,: was selected to ma"e pro+ision
for the 9/ design.
Which of the following addresses can be assigned to hosts on the
resulting subnets? 0Select three options.1
. 166.1,1.(2.1(3
#. 166.1,1.(2.125
$. 166.1,1.(2.77
D. 166.1,1.(2.116
%. 166.1,1.(2.(:4
F. 166.1,1.(2.11(
nswer' )$)D
16:. 8ou ha+e been as"ed to configure a default route.
Which of the IOS commands mentioned below will accomplish this
tas"? 0Select two options.1
. 9!D0config1< ip route :.:.:.: :.:.:.: 16(.134.15.73
#. 9!D0config1< ip route :.:.:.: 16(.134.15.73 (55.(55.(55.(55
$. 9!D< ip default=networ" :.:.:.: 16(.134.15.73 (55.(55.(55.(55
D. 9!D0config1< ip route :.:.:.: :.:.:.: %:
%. 9!D0config1< ip route :.:.:.: (55.(55.(55.(55 S:
F. 9!D0config=router1< ip route (55.(55.(55.(55 :.:.:.:
16(.134.15.73
nswer' )D
161. Why is it beneficial for indi+iduals in the data
communication industry to use the layered OSI reference model?
0Select two options.1
. It encourages industry standardiJation by defining what
functions occur at each layer of the model.
#. It necessitates changes in functionality in one layer to other
layers.
$. It enables e;uipment efficiency from different +endors to use
the same electronic components.
D. It di+ides the networ" communication process into smaller and
simpler components) thus aiding
component de+elopment) design) and troubleshooting.
%. It supports the e+olution of multiple competing standards) and
thus enhances business e;uipment manufacturing opportunities.
nswer' )D
16(. Which routing protocol would allow a networ" administrator
scalability and D9SG support and
minimiJe o+erhead if the networ" administrator want to merge
different networ"s all using routers from multiple +endors.
. D!P
#. *IP
$. %I&*P
D. OSPF
%. I&*P
nswer' D
16,. When you e-ecute *outer< show frame=relay) which of the
following command options will be displayed? 0Select three
options.1
. dlci
#. clients
$. p+c
D. neighbors
%. lmi
F. map
nswer' $)%)F
165. newly assigned trainee wants to "now from you what the
SInside &lobalS address represents in the configuration of /!.
What can you tell him?
. !he G$ address used by inside hosts to connect to the
Internet.
#. !he summariJed address for all internal subnetted addresses.
$. pri+ate IP address assigned to a host on the inside networ".
D. registered address that represents an inside host to an
outside networ".
%. uni;ue IP address used on an intranet.
nswer' D
163. What does the concept route aggregate mean when one tal"s
about using +ariable subnet mas"ing?
. Deleting unusable addresses through the creation of many
subnets.
#. $ombining routes to multiple networ"s into one supernet.
$. *eclaiming unused space by means of changing the subnet siJe.
D. $alculating the a+ailable host addresses in the S.
nswer' #
162. Which of the following statements describes full or half=
duple- %thernet operation correctly? 0Select two options.1
. Full=duple- %thernet uses $SG@$D to pre+ent collisions.
#. Calf=duple- %thernet uses a loopbac" circuit to detect
collisions.
$. full=duple- %thernet card allows (:Gbps for data
transmission.
D. Full=duple- %thernet ma"es use of two pairs of wires for data.
%. n %thernet hub can operate both half and full duple-
simultaneously.
nswer' #)D
164. Select two of the following statements that are
characteristics of a Frame *elay point=to=point subinterface.
. /eeds to use In+erse *P.
#. Gaps a single IP subnet per D9$I.
$. Gaps a single IP subnet across multiple D9$Is.
D. ddresses and resol+es /#G split horiJon issues.
%. /eeds the frame=relay map command.
nswer' #)D
166. 8ou wor" as a networ" administrator for !est.ing.com. 8ou
must design an IP addressing scheme to support the companyEs
networ" that will pro+ide for a minimum of 7:: sub=networ"s and a
ma-imum of 5: host addresses per subnet. Which of the following
subnet mas"s will enable you to support an appropriate addressing
scheme gi+en the fact that you wor" with only one $lass #
address. 0Select two options.1
. (55.(55.(55.:
#. (55.(55.(55.16(
$. (55.(55.(,4.:
D. (55.(55.(5(.:
%. (55.(55.(55.1(4
F. (55.(55.(55.((,
nswer' #)%
(::. Study the %-hibit below carefully'
!he ISP assigned /etwor" (:2.17,.3.: to !est.ing. 8ou are the
networ" administrator at !est.ing and would li"e to configure one
router with the commands to access the Internet.
Which of the following commands will you use to configure the
&ateway *outer to allow Internet access to the entire networ"?
0Select two options.1
. &ateway0config1< ip route :.:.:.: :.:.:.: (:2.17,.3.1.
#. &ateway0config1< router rip
&ateway0config=router1< networ" (:2.17,.3.: default
$. &ateway0config1< ip route (:2.17,.3.: (55.(55.(55.: Serial:@:
D. &ateway0config1< router rip
&ateway0config=router1< networ" (:2.17,.3.:
%. &ateway0config1< ip default=networ" (:2.17,.3.:
nswer' )%
(:1. Study the %-hibit below carefully'
!elnet traffic from the &raphics Department is prohibited from
reaching the C* ser+er attached to the !est.ing( router) but will
allow !elnet traffic to other destinations due to an access list
that has been designed to do precisely this. &i+en the following
access list'
access=list 1:1 deny tcp any any e; (7
permit ip any any
On which router) in what direction) and which interface) should
the access list be placed to most
efficiently implement the abo+e list? 0Select three options.1
. !est.ing1
#. !est.ing(
$. out
D. in
%. s:
F. e:
nswer' #)$)F
(:(. Study the %-hibit below carefully'
bo+e is an illustration of the output of the 9ondon switch. What
is the function of this switch?
. 9earn and sa+ed D!P configuration in the running
configuration.
#. $reate and change D9/s.
$. Passes information about D!P configuration.
D. D!P is disabled on this de+ice.
%. D!P is not sa+ed to /D*G.
nswer' $
(:,. Study the %-hibit below carefully'
remote site has Fust been connected to the central office.
Cowe+er) remote users can not access
applications at the central office. !he remote router can be
pinged from the central office router. fter re+iewing the
command output shown in the e-hibit illustrated abo+e) what is
the most li"ely reason for the problem?
. !he Frame *elay PD$ is down.
#. !he IP addressing on the $entral@*emote serial lin" is
incorrect.
$. *IP routing information is not being forwarded.
D. Frame *elay in+erse=*P is not properly configured.
nswer' $
(:5. /etwor" !opology %-hibit'
$onsider the scenario as depicted in the e-hibit. ssuming the
following aims'
11 allow !elnet from the Internet to the C* ser+er
(1 allow C!!P access from the Internet to the web ser+er
71 all other traffic from the Internet should be bloc"ed
Which of the following access list statements do you thin" are
necessary to accomplish all three aims? 0Select two options.1
. access=list 1:1 permit tcp any 12(.12.14.(5( :.:.:.: e; 4:
#. access=list 1 permit tcp any 12(.12.12.(5( :.:.:.: e; (7
$. access=list 1:1 permit tcp 12(.12.12.(5( :.:.:.: any e; (7
D. access=list 1:1 deny tcp any 12(.12.12.(5( :.:.:.: e; (7
%. access=list 1:1 deny tcp any 12(.12.14.(5( :.:.:.: e; 4:
F. access=list 1:1 permit tcp any 12(.12.12.(5( :.:.:.: e; (7
nswer' )F
(:3. Study the %-hibit below carefully'
Which of the statements mentioned below will describe the networ"
as illustrated in the e-hibit? 0Select two options.1
. !here are two broadcast domains in the networ".
#. !here are four broadcast domains in the networ".
$. !here are si- broadcast domains in the networ".
D. !here are four collision domains in the networ".
%. !here are fi+e collision domains in the networ".
F. !here are se+en collision domains in the networ".
nswer' )F
(:2. Which of the following commands will display the $CP
authentication process as it occurs between the two routers in
the networ" when you "now that all W/ lin"s inside the companyEs
networ" use PPP with $CP for authentication security?
. show ppp authentication
#. debug PP authentication
$. debug PPP authentication
D. show interface serial:
%. show $CP authentication
nswer' $
(:4. Which of the following commands are re;uired to create an
4:(.1I lin" on an IOS based switch when you want to establish a
trun" lin" between two switches? 0Select two options.1
. Switch0+lan1< mode trun"
#. Switch0config1< switchport access mode trun"
$. Switch0config=if1< switchport mode trun"
D. Switch0config=if1< switchport trun" encapsulation dot1;
%. Switch0config1< switchport access mode 1
F. Switch0+lan1< trun" encapsulation dot1;
nswer' $)D
(1:. Cow would you configure a router in a Frame *elay networ" to
pre+ent issues such as split horiJons hampering routing updates?
. $onfigure a separate sub=interface for each PD$ with a uni;ue
D9$I and subnet assigned to the subinterface.
#. $onfigure many sub=interfaces on the same subnet.
$. $onfigure each Frame *elay circuit as a point=to=point line.
D. $onfigure only one sub=interface to establish multiple PD$
connections.
%. $onfigure a single sub=interface connect to multiple remote
router interfaces.
nswer'
(11. Study the %-hibit below carefully'
hostname #arrymore
T
enable password gate"eeper
T
isdn switch=type basic=5ess
T
T
username $entral password cisco
interface #*I:
ip address 16(.134.:.1 (55.(55.(55.:
encapsulation ppp
dialer idle=timeout 14:
dialer map ip 16(.134.:.( name *emote 333(:::
dialer=group 1
no fair=;ueue
ppp authentication chap
T
router rip
networ" 16(.134.:.(
T
no ip classless
ip route 16(.134.1:.: (55.(55.:.: 16(.134.:.(
ip route 16(.134.(:.: (55.(55.:.: 16(.134.:.(
T
dialer=list 1 protocol ip permit
bo+e is the result of the output of show running=config command.
What is causing the problem when the #arrymore router is unable
to ma"e calls to the remote site?
. !he authentication password is missing from the dialer map
command.
#. !he switch=type must be configured.
$. *outing updates are being bloc"ed by the applied dialer=list.
D. !he dialer list only permits one protocol.
%. !he name in the dialer=map must match the name in the username
command.
nswer' %
(1(. ssuming that all OSPF routers in a particular area are
configured with identical priority +alues) which of the following
+alues would a router use for OSPF router ID when it does not
ha+e a loopbac" interface?
. !he IP address of the first Fast %thernet interface.
#. !he IP address of the console management interface.
$. !he highest IP address among its acti+e interfaces.
D. !he lowest IP address among its acti+e interfaces.
%. !he priority +alue until a loopbac" interface is configured.
nswer' $
(17. Study the %-hibit below carefully'
Which of the following is the correct IP address configuration
for Cost?
. IP 16(.134.1::.71 (55.(55.(55.(,: default=gateway
16(.134.1::.14
#. IP 16(.134.1::.7: (55.(55.(55.(,: default=gateway 12(.13.1.1
$. IP 16(.134.1::.(: (55.(55.(55.(,: default=gateway
16(.134.1::.12
D. IP 16(.134.1::.(1 (55.(55.(55.(,4 default=gateway
16(.134.1::.12
%. IP 16(.134.1::.16 (55.(55.(55.(,4 default=gateway 12(.13.1.1
nswer' $
(1,. Study the %-hibit below carefully'
fter considering the command output of both routers) what is the
cause of the problem if connecti+ity cannot be established
between the two routers?
. uthentication needs to be changed to PP for both routers.
#. Serial ip addresses of routers are not on the same subnet.
$. Bsername@password is incorrectly configured.
D. *outer names are incorrectly configured.
nswer' $
(12. Which of the following types of pac"ets will be allowed
entry when a serial interfaceEs inbound access list has been
configured to prohibit entry for !$P and BDP ports (1) (7 and (5?
0Select 7.1
. SG!P
#. D/S
$. F!P
D. !elnet
%. C!!P
F. POP7
nswer' #)%)F
(14. One of the !est.ing.com trainees assigned to you want to
"now which ser+ices use !$P. What can you tell him? 0Select three
options.1
. DC$P
#. SG!P
$. S/GP
D. F!P
%. C!!P
F. !F!P
nswer' #)D)%
(16. Which of the following networ" mas"s would you use to reduce
any wastage of IP addresses in point=topoint
W/ lin"s on a networ" that supports D9SG?
. @74
#. @7:
$. @(2
D. @(7
%. @14
nswer' #
((:. Cow would you configure a router to a+oid situations such as
split horiJon issues hampering routing updates on a Frame *elay
networ"?
. $onfigure a separate sub=interface for each PD$ with a uni;ue
D9$I and subnet assigned to the subinterface.
#. $onfigure each Frame *elay circuit as a point=to=point line to
support multicast and broadcast traffic.
$. $onfigure one sub=interface to disperse into multiple PD$
connections to multiple remote router interfaces.
D. $onfigure as many as possible sub=interfaces on the same
subnet.
nswer'
((7. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what the characteristics of named
access list are. What would your reply be? 0$hoose (.1
. 8ou can delete indi+idual statements in a named access list.
#. /amed access lists re;uire a numbered range from 1::: to 1:66.
$. /amed access lists must be specified as standard or e-tended.
D. 8ou can use the ip access=list command to create named access
lists.
%. 8ou cannot delete indi+idual statements in a named access
list.
F. 8ou can use the ip name=group command to apply named access
lists.
nswer' )$)D
((5. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now which ser+ices use BDP. What would
your reply be? 0$hoose (.1
. !$$S
#. !elnet
$. SG!P
D. S/GP
%. C!!P
F. !F!P
nswer' D)F
((4. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what the purpose of In+erse *P
is. What will your reply be?
. It is used to map a "nown IP address to a G$ address
#. It is used to map a "nown D9$I to a G$ address
$. It is used to map a "nown G$ address to an IP address
D. It is used to map a "nown D9$I to an IP address
%. It is used to map a "nown G$ address to D9$I
F. It is used to map a "nown D9$I to a G$ address
nswer' D
((6. 8ou are the networ" administrator at !est.ing. 8ou +erify
the configuration of a newly installed host by establishing an
F!P connection to a remote ser+er.
What is the highest layer of the protocol stac" used in this
operation?
. application
#. presentation
$. session
D. transport
%. networ"
F. data lin"
&. physical
nswer'
(71. 8ou are the networ" administrator at !est.ing. !he !est.ing
networ" is shown in the following e-hibit'
8ou want to apply the following access control list to one of the
!est.ing routers.
access=list 1:1 permit tcp 16(.134.1.13 :.:.:.15 16(.134.( 13
:.:.:.15 e; (7
With regard to this scenario) which of the following statements
are true? 0$hoose (.1
. !elnet traffic from 16(.134.1.13 :.:.:.15 to 134.(.13 :.:.:.15
is allowed.
#. SG!P traffic from 16(.134.1.13 :.:.:.15 to 134.(.13 :.:.:.15
is allowed.
$. !he $9 is configured to allow traffic from one specific host
to another.
D. !he $9 should be applied inbound to the e: interface of
*outer !est.ing1.
%. !he $9 should be applied outbound to the e: interface of
*outer !est.ing1.
nswer' )D
(7(. 8ou are a trainee technician at !est.ing. 8our instructor
shows you the following output'
She tells you that the output was ta"en from two directly
connected routers. 8our instructor wants to "now which of the
following lines will be displayed when you issue the *outer< show
interface serial: command.
What will your reply be? 0$hoose 7.1
. Serial : is down) line protocol is down
#. Serial : is up) line protocol is up
$. Open' IP$P) $DP$P
D. 9$P closed
%. 9$P open
nswer' #)$)%
(77. 8ou are a technician at !est.ing. 8ou ha+e encapsulated an
ISD/ lin" on the !est.ing networ" with PPP. 8our newly appointed
!est.ing trainee wants to "now why you did not use CD9$ to
encapsulate the ISD/ lin".
What will your reply be? 0$hoose (.1
. PPP is easier to configure and maintain than CD9$.
#. Different e;uipment +endors consistently implement PPP.
$. PPP can be routed across public facilities) while CD9$ is not.
D. PPP uses authentication to pre+ent unauthoriJed access to the
ISD/ circuit.
%. On circuit=switched ISD/ lin"s PPP is faster and more
efficient than CD9$.
nswer' #)D
(7,. 8ou are the networ" administrator at !est.ing. !est.ing has
an OSPF networ". 8ou want to obser+e the D*@#D* election process
in the !est.ing networ". What command can you issue in pri+ileged
%M%$ mode to accomplish this?
. !.1< show ip ospf interface
#. !.1< show ip ospf priority
$. !.1< show ospf neighbor detail
D. !.1< show ospf processes
%. !.1< show ospf neighbor state
nswer'
(75. 8ou are the networ" technician at !est.ing. !est.ing has a
router that is connected to a Frame *elay W/ lin" using a serial
D!% interface. 8our newly appointed !est.ing trainee wants to
"now how the interface cloc" rate is determined on this router.
What will your reply be?
. It is determined by the $SB@DSB.
#. It is determined by the far end router.
$. It is specified in the cloc" rate command.
D. It is determined by the 9ayer 1 bit stream timing.
nswer'
(73. 8ou are the networ" technician at !est.ing. 8ou tell your
newly appointed !est.ing trainee that discontiguous networ"s in
the IP addressing scheme can create problems when a routing
protocol tries to identify the ne-t hop. 8our trainee now wants
to "now which routing protocols can be used to minimiJe the
effects of these problems.
What would your reply be? 0$hoose 7.1
. I&*P
#. I$GP
$. OSPF
D. *IP +1
%. *IP +(
F. %I&*P
nswer' $)%)F
(72. 8ou are the networ" engineer at !est.ing. 8our !est.ing
trainee !ess wants to "now which parameter must be supplied when
you initialiJe the I&*P routing process.
What should you tell her?
. !he wild card mas"
#. !he IP address
$. !he IP address mas"
D. !he metric weights
%. !he utonomous System number
nswer' %
(74. 8ou are the networ" technician at !est.ing. !est.ing has a
switched networ". 8ou want to add a new D9/ to the networ".
Which steps would you ta"e to configure this D9/? 0$hoose 7.1
. $reate the D9/.
#. /ame the D9/.
$. $onfigure an IP address for the D9/.
D. dd the desired ports to the new D9/.
%. dd the D9/ to the S!P domain.
nswer' )#)D
(76. 8ou are the networ" administrator at !est.ing. !he !est.ing
networ" has e-panded considerably o+er the last year. It is now
one large) cumbersome networ". 8ou want to segment the networ".
What de+ices can you use? 0$hoose 7.1
. Cubs
#. *epeaters
$. Switches
D. #ridges
%. *outers
nswer' $)D)%
(,:. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what is specific for a global
command. What should you tell her?
. command that is a+ailable in e+ery release of IOS.
#. command that can be entered in any configuration mode.
$. command that supports all protocols.
D. command that is implemented in all IOS +ersions.
%. command that is set once and affects the entire router.
nswer' %
(,1. 8ou are a trainee technician at !est.ing. 8our instructor
wants you to con+ert the first octet in $lass # address range to
binary.
What would your reply be?
. :::::111=1:::1111
#. ::::::11=1::11111
$. 1:::::::=1:111111
D. 11::::::=11:11111
%. 111:::::=111:1111
nswer' $
(,(. 8ou are a technician at !est.ing. 8ou tell your newly
appointed !est.ing trainee that %thernet networ"s are broadcast
domains and collision domains. 8our trainee wants to "now what
happens when a collision occurs on the networ".
What would your reply be? 0$hoose 7.1
. %ach de+ice stops transmitting for a short time.
#. Fam signal informs all de+ices that a collision occurred.
$. When data transmission resumes) the de+ices that were in+ol+ed
in the collision ha+e priority to transmit.
D. !he de+ices that are in+ol+ed in the collision stops
transmitting for a short time.
%. !he collision in+o"es a random bac"=off algorithm.
nswer' #)D)%
(,7. 8ou are a technician at !est.ing. !est.ing plans to
implement a public networ". !he companyEs ISP suggested that
!est.ing register a $lass IP address. !he !est.ing $%O wants to
"now how many usable IP addresses are pro+ided in a $lass $
address.
What would your reply be?
. 1(4
#. 16(
$. (5,
D. (53
%. 51:
nswer' $
(,2. Which of the following statements describes a con+erged
spanning=tree networ"?
. ll switch and bridge ports are in the forwarding state.
#. ll switch and bridge ports are in the stand=by state.
$. ll switch and bridge ports are assigned as either root or
designated ports.
D. ll switch and bridge ports are in either the forwarding or
bloc"ing state.
%. ll switch and bridge are either bloc"ing or looping.
nswer' D
(,4. s what type of physical networ" is a default Frame *elay
W/ classified?
. point=to=point
#. broadcast multi=access
$. nonbroadcast multipoint
D. nonbroadcast multi=access
%. broadcast point=to=multipoint
nswer' D
(,6. 8ou are the networ" administrator at !est.ing. !est.ing has
its head;uarters in /ew 8or") and regional offices in #oston)
#uffalo) $le+eland) Pittsburgh and #altimore. 8ou want to connect
the regional offices to head;uarters. 8ou are e+aluating W/
technologies that could accomplish this. 8ou want each regional
office to be connected to the corporate head;uarters in a hub and
spo"e arrangement using a pac"et=switched technology.
Which of the following W/ technologies should you use?
. ISD/
#. Wireless
$. Frame *elay
D. !1 leased line
%. Point to point leased line
nswer' $
(5:. 8ou are the networ" administrator at !est.ing. !he !est.ing
networ" is shown in the following e-hibit'
8ou use the ip access=group 1:1 in command to apply the following
access control list on the e: interface of router !.1.
access=list 1:1 deny tcp 5.1.1.1: :.:.:.: 5.1.7.: :.:.:.(55 e;
telnet
access=list 1:1 permit any any
Which of the following will be bloc"ed? 0$hoose two.1
. !elnet sessions from host to host 5.1.1.1:
#. !elnet sessions from host to host 5.1.7.1:
$. !elnet sessions from host # to host 5.1.7.1:
D. !elnet sessions from host # to host 5.1.7.4
%. !elnet sessions from host $ to host 5.1.7.1:
F. !elnet sessions from host F to host 5.1.1.1:
nswer' $)D
(51. 8ou are a networ" administrator at !est.ing. !o routers on
the !est.ing networ") router !.1 and router !.( are configured to
run OSPF. Cowe+er) the two routers cannot establish an adFacency
relationship on their common %thernet lin". In troubleshooting
this problem you issue the show ip ospf interface e: command for
routers !.1 and !.(. !he output from the command is shown in the
following e-hibit'
#ased on the e-hibit) what is the probable cause of this problem?
. !he OSPF area is misconfigured.
#. !he priority on !.( should be set lower.
$. !he cost on !.( should be set lower.
D. !he hello and dead timers are misconfigured.
%. 8ou need to add a bac"up designated router to the networ".
F. !he OSPF process ID numbers do not match.
nswer' D
(5(. 8ou are a networ" administrator at !est.ing. 8our assistant
has been attempting to establish a lin" between interface s:@: on
router !.1 and interface s:@: on router !.( but his attempts ha+e
failed. Ce as"s for your assistance.
8ou issue the show interface s:@: command on router !.1 and
router !.(. !he output from the show
interface s:@: commands is shown in the following e-hibit'
#ased on the e-hibit) what is the most li"ely cause of this
problem?
. !he loopbac" is not set.
#. !he serial cable is faulty.
$. !he subnet mas" is not configured properly.
D. !he IP address is not configured properly.
%. !he 9ayer ( frame types are not compatible.
nswer' %
(57. 8ou are the networ" administrator at !est.ing. !he *IP
routing protocol is being used on the !est.ing networ". *IP is
configured with default settings and e;ual cost load balancing.
!he !est.ing networ" has si- paths with the same metric and
administrati+e distance for a single destination. Which of the
si- paths will *IP use to reach the destination?
. Only the first two paths that are learned.
#. Four of the paths.
$. ll si- routes in a routed robin fashion.
D. !he oldest two paths in the routing table.
%. !he first path learned to the destination networ".
nswer' #
(5,. 8ou are the networ" administrator at !est.ing. 8ou want to
configure a default route to any destination networ" not found in
the routing table on router !.1.
Which of the following commands can you issue?
. !.10config1< ip default=route :.:.:.: (55.(55.(55.(55 s:
#. !.10config1< ip route :.:.:.: (55.(55.(55.(55 s:
$. !.10config1< ip default=route :.:.:.: s:
D. !.10config1< ip route :.:.:.: :.:.:.: s:
%. !.10config1< ip route any any e:
nswer' D
(55. 8ou are the networ" administrator at !est.ing. 8our newly
appointed !est.ing trainee wants to "now which protocol uses both
tcp and udp ports.
What will your reply be?
. F!P
#. !F!P
$. SG!P
D. !elnet
%. D/S
nswer' %
(53. 8ou are the networ" administrator at !est.ing. 8our newly
appointed !est.ing trainee wants to "now what the default
administrati+e distance of OSPF routing protocol is.
What will your reply be?
. 6:
#. 1::
$. 11:
D. 1(:
%. 12:
nswer' $
(52. 8ou are the networ" administrator at !est.ing. 8ou must
configure a router for load balancing across , une;ual cost paths
on the !est.ing networ".
Which of the following routing protocols can you use? 0$hoose
two.1
. *IP +1
#. *IP +(
$. I&*P
D. %I&*P
%. OSPF
F. D9SG
nswer' $)D
(54. 8ou are the networ" administrator at !est.ing. !est.ing
users report that they cannot access resources on the 9/
attached to interface e: of router !.1. 8ou want to +iew the
current IP addressing and the 9ayer 1 and 9ayer ( status of this
interface.
Which of the following commands could you use? 0$hoose three.1
. !.1< show +ersion
#. !.1< show protocols
$. !.1< show interfaces
D. !.1< show controllers
%. !.1< show ip interface
F. !.1< show startup=config
nswer' $)D)%
(56. 8ou are the networ" administrator at !est.ing. 8our need to
design an IP addressing scheme to support a nationwide networ".
!est.ing needs a minimum of 7:: sub=networ"s) each of which must
support a ma-imum of 5: host addresses. !est.ing has been
assigned a $lass # address by its ISP. Which of the following
subnet mas"s will support the appropriate addressing scheme?
0$hoose two.1
. (55.(55.(55.:
#. (55.(55.(55.1(4
$. (55.(55.(5(.:
D. (55.(55.(55.((,
%. (55.(55.(55.16(
F. (55.(55.(,4.:
nswer' #)%
(3:. Which of the following routing protocols minimiJe the
effects of the problems created by discontiguous networ"s?
0$hoose three.1
. *IP +1
#. *IP +(
$. %I&*P
D. I&*P
%. OSPF
F. D9SG
nswer' #)$)%
(31. 8ou are the networ" administrator at !est.ing. 8our !est.ing
trainee is wor"ing in a lab that has a Frame *elay networ" in
which In+erse *P is not operational. She wants to "now which
command would pro+ide connecti+ity in this networ".
What will your reply be?
. frame=relay arp
#. frame=relay map
$. frame=relay interface=dlci
D. frame=relay lmi=type
nswer' #
(3(. 8ou are the networ" administrator at !est.ing. 8our newly
appointed !est.ing trainee wants to "now what D9/ frame
encapsulation types may be configured on a $atalyst switch.
What will your reply be? 0$hoose two.1
. D!P
#. IS9
$. $DP
D. 4:(.1I
%. 4:(.1p
F. 99$
nswer' #)D
(37. 8ou are the networ" administrator at !est.ing. 8ou need to
configure a default route on the !est.ing networ". Which the
following IOS commands could you use? 0$hoose two.1
. !.10config1< ip route :.:.:.: :.:.:.: %:
#. !.10config1< ip route :.:.:.: (55.(55.(55.(55 S:
$. !.10config=router1< ip route (55.(55.(55.(55 :.:.:.:
16(.134.1.(1
D. !.10config1< ip route :.:.:.: :.:.:.: 16(.134.1.(1
%. !.10config1< ip route :.:.:.: 16(.134.1.(1 (55.(55.(55.(55
F. !.1< ip default=networ" :.:.:.: 16(.134.1.(1 (55.(55.(55.(55
nswer' )D
(3,. 8ou are the newly appointed !est.ing trainee. 8our
super+isor tells you that the IP address for your wor"station is
12(.13.(:6.1:@((. Ce wants to "now what the subnetwor" number of
your wor"station is. What will your reply be?
. 12(.13.,(.:
#. 12(.13.1:2.:
$. 12(.13.(:4.:
D. 12(.13.(5(.:
%. 12(.13.(5,.:
nswer' $
(35. With regard to classless routing protocols) which of the
following statements are true? 0$hoose two.1
. Discontiguous subnets are not allowed.
#. Dariable length subnet mas"s are allowed.
$. *IP +1 is a classless routing protocol.
D. I&*P supports classless routing within the same autonomous
system.
%. *IP +( supports classless routing.
nswer' #)%
(33. 8ou are the networ" administrator at !est.ing. 8ou issue the
show ip route command on a router during routine maintenance. !he
output from the show ip route command indicates a networ" that is
ad+ertised by both *IP and I&*P as an I&*P route. 8our !est.ing
assistant wants to "now why the *IP route to the networ" is not
used in the routing table.
What will your reply be?
. I&*P has a faster update timer.
#. I&*P has a lower administrati+e distance.
$. *IP has a higher metric +alue for that route.
D. !he I&*P route has fewer hops.
%. !he *IP path has a routing loop.
nswer' #
(32. 8ou are the networ" administrator at !est.ing. 8our
assistant was unsuccessful in adding D9/ 5: to a switch. In
troubleshooting the problem) you issue the show +tp status
command. !he output of the show +tp status command is displayed
in the following e-hibit.
!.(< show +tp status
D!P Dersion '(
$onfiguration *e+ision '2
Ga-imum D9/s supported local '34
/umber of e-isting D9/s '4
D!P Operating Gode '$lient
D!P Domain /ame 'corp
D!P Pruning Gode 'Disabled
D!P D( Gode 'Disabled
D!P !raps &eneration 'Disabled
GD5 digest ':-(( :-F7 :-1
$onfiguration last modified by 12(.14.((.15 at 5=(4=:7 1t'57'(:
What commands must be issued on this switch to add D9/ 5: to the
database? 0$hoose two.1
. !.(0config=if1< switchport access +lan 5:
#. !.(0+lan1< +tp ser+er
$. !.(0config1< config=re+ision (:
D. !.(0config1< +lan 5: name !ech
%. !.(0+lan1< +lan 5:
F. !.(0+lan1< switchport trun" +lan 5:
nswer' #)%
(34. 8ou are the networ" administrator at !est.ing. !he !est.ing
networ" has the address of 16(.1.1.:@(, and is using *IP as the
routing protocol. portion of the networ" is shown in the
following e-hibit'
8ou want to configure router !.1 for 9/=to=9/ communication
with router !.(.
Which series of commands should you issue? 0$hoose three.1
. !.10config1< interface ethernet :
!.10config=if1< ip address 16(.1.1.1(6 (55.(55.(55.16(
!.10config=if1< no shutdown
#. !.10config1< interface ethernet :
!.10config=if1< ip address 16(.1.1.62 (55.(55.(55.16(
!.10config=if1< no shutdown
$. !.10config1< interface serial :
!.10config=if1< ip address 16(.1.1., (55.(55.(55.(5(
!.10config=if1< cloc" rate 53:::
D. !.10config1< interface serial :
!.10config=if1< ip address 16(.1.1.3 (55.(55.(55.(5(
!.10config=if1< no shutdown
%. !.10config1< router rip
!.10config=router1< networ" 16(.1.1.,
!.10config=router1< networ" 16(.1.1.1(4
F. !.10config1< router rip
!.10config=router1< +ersion (
!.10config=router1< networ" 16(.1.1.:
nswer' )D)F
(36. 8ou are the networ" administrator at !est.ing. portion of
the networ" is shown in the following e-hibit'
8ou configure a static route to the 1:.5.3.:@(, networ" on router
!est.ing. 8ou want router !est.ing to treat this static route as
the most reliable route.
Which command should you use? 0choose (1
. !est.ing0config1< ip route 1:.5.3.: :.:.:.(55 fa:@:
#. !est.ing0config1< ip route 1:.5.3.: :.:.:.(55 1:.5.,.3
$. !est.ing0config1< ip route 1:.5.3.: (55.(55.(55.: fa:@:
D. !est.ing0config1< ip route 1:.5.3.: (55.(55.(55.: 1:.5.,.3
%. !est.ing0config1< ip route 1:.5.,.3 :.:.:.(55 1:.5.3.:
F. !est.ing0config1< ip route 1:.5.,.3 (55.(55.(55.: 1:.5.3.:
nswer' $)D
(2:. 8ou are the networ" administrator at !est.ing. 8our newly
appointed !est.ing trainee wants to "now what router functions
are.
What will your reply be? 0$hoose three.1
. Pac"et switching
#. $ollision pre+ention on a 9/ segment.
$. Pac"et filtering
D. #roadcast domain enlargement
%. #roadcast forwarding
F. Internetwor" communication
nswer' )$)F
(21. With regard to the DC$P Disco+er message) which of the
following are true? 0$hoose two.1
. !he DC$P Disco+er message uses FF=FF=FF=FF=FF as the 9ayer (
destination address.
#. !he DC$P Disco+er message uses BDP as the transport layer
protocol.
$. !he DC$P Disco+er message uses a special 9ayer ( multicast
address as the destination address.
D. !he DC$P Disco+er message uses !$P as the transport layer
protocol.
%. !he DC$P Disco+er message does not use a 9ayer ( destination
address.
F. !he DC$P Disco+er message does not re;uire a transport layer
protocol.
nswer' )#
(2(. 8ou are the networ" administrator at !est.ing. 8ou want to
configure the D9/ trun"ing protocol to communicate D9/
information between two switches.
What must you do? 0$hoose two.1
. Set each end of the trun" line to I%%% 4:(.1% encapsulation.
#. Set the same D!P management domain name on both switches.
$. Set all ports on the two switched as access ports.
D. $onfigure one of the two switches as a D!P ser+er.
%. $onnect the two switches using a rollo+er cable.
F. Bse a router to forward D!P traffic between the D9/s.
nswer' #)D
(27. series of Switches are connected as shown in the following
e-hibit'
Which portion contains both the potential networ"ing problem and
the protocol or setting that would be used to pre+ent this
problem?
. routing loops) hold down timers
#. switching loops) split horiJon
$. routing loops) split horiJon
D. switching loops) D!P
%. routing loops) S!P
F. switching loops) S!P
nswer' F
(25. Which of the following layers are part of the !$P@IP model?
0$hoose three.1
. application layer
#. session layer
$. transport layer
D. internet layer
%. networ" layer
F. data lin" layer
&. physical layer
nswer' )$)D
(23. 8ou are the networ" administrator at !est.ing. !he !est.ing
networ" is shown in the following e-hibit'
With regard to the routing decision router will ma"e to reach
router %) which of the following
statements are true? 0$hoose three.1
. *outer will determine that all paths ha+e an e;ual cost if
*IP is the routing protocol.
#. *outer will install only the D% path in its routing table
if *IP is the routing protocol.
$. *outer will determine that path $% has the lowest cost if
I&*P is the routing protocol.
D. *outer will determine that path D% has the lowest cost if
I&*P is the routing protocol.
%. *outer will use the route information learned by I&*P if
both *IP and I&*P are configured on router .
F. *outer will use the route information learned by *IP if both
*IP and I&*P are configured on router .
nswer' )D)%
(22. 8ou are a networ" administrator at !est.ing. 8ou want to
deny networ" traffic from a specific host. Which access list
statement should you use?
. *outer0config1< access=list 1 deny 12(.71.(1(.2, any
#. *outer0config1< access=list 1 deny 1:.3.111.,4 host
$. *outer0config1< access=list 1 deny 12(.13.,.17 :.:.:.:
D. *outer0config1< access=list 1 deny 16(.134.1,.17(
(55.(55.(55.:
%. *outer0config1< access=list 1 deny 16(.134.133.1(2
(55.(55.(55.(55
nswer' $
(24. 8our newly appointed !est.ing trainee wants to "now at what
layers of the OSI reference model a W/s operates. What will your
reply be? 0$hoose two.1
. pplication layer
#. Presentation layer
$. Session layer
D. !ransport layer
%. /etwor" layer
F. Data lin" layer
&. Physical layer
nswer' %)F
(4:. Which of the following are general recommendations for the
placement of access control lists? 0$hoose two.1
. 8ou should place standard $9S as close as possible to the
source of traffic to be denied.
#. 8ou should place e-tended $9S as close as possible to the
source of traffic to be denied.
$. 8ou should place standard $9S as close as possible to the
destination of traffic to be denied.
D. 8ou should place e-tended $9S should be places as close as
possible to the destination of traffic to be denied.
nswer' #)$
(4(. 8ou are the networ" administrator at !est.ing. 8ou want to
configure a switch port to use the I%%% standard method of
inserting information about D9/ membership into %thernet frames.
Which command should you use?
. Switch0config1< switchport trun" encapsulation isl
#. Switch0config1< switchport trun" encapsulation ietf
$. Switch0config1< switchport trun" encapsulation dot1;
D. Switch0config=if1< switchport trun" encapsulation isl
%. Switch0config=if1< switchport trun" encapsulation ietf
F. Switch0config=if1< switchport trun" encapsulation dot1;
nswer' $
(47. 8our newly appointed !est.ing trainee wants to "now which of
the following are spanning tree switch port states.What will your
reply be? 0$hoose three1
. learning
#. spanning
$. listening
D. forwarding
%. initialiJing
F. filtering
nswer' )$)D
(4,. !est.ing has been assigned the $ID* bloc" of 115.3,.,.:@((
for its public networ". Which of the following IP addresses can
!est.ing use on its public networ"?0choose 71
. 115.3,.4.7(
#. 115.3,.2.3,
$. 115.3,.3.(55
D. 115.3,.7.(55
%. 115.3,.5.1(4
F. 115.3,.1(.1(4
nswer' #)$)%
(45. 8ou are the networ" technician at !est.ing. !wo routers on
the !est.ing networ") *outer !.1 and *outer !.( are configured
with *IP only. *outer !.1 recei+es a routing update with a higher
cost path to a remote networ" that is already in its routing
table.
What will *outer !.1 do?
. It will ignore the update and ta"e no further action.
#. It will add the update information to its routing table.
$. It will replace the e-isting routing table entry with the
update information.
D. It will delete the e-isting routing table and will send out
hello pac"ets to rebuild the routing table.
nswer'
(43. !he !est.ing networ" has a conferencing system that uses
Doice o+er IP. !he system uses BDP
datagrams to send the +oice data between communicating hosts.
8our newly appointed !est.ing trainee wants to "now what will
happen if the datagrams out of se;uence arri+e at their
destination when the networ" becomes busy.
What will your reply be?
. BDP will send an I$GP Information *e;uest to the source host.
#. BDP will pass the information in the datagrams up to the ne-t
OSI layer in the order that they arri+e.
$. BDP will drop the datagrams.
D. BDP will use the se;uence numbers in the datagram headers to
reassemble the data in the correct order.
%. BDP will not ac"nowledge the datagrams and wait for a
retransmission of the datagrams.
nswer' $
(42. 8ou are the networ" administrator at !est.ing. 8ou are
troubleshooting an %I&*P problem on *outer !.1. 8ou want to chec"
the IP addresses as well as the retransmit inter+al and the ;ueue
counts for the de+ices which ha+e established an adFacency with
*outer !.1.
What command should you issue?
. !.1<show ip eigrp adFacency
#. !.1<show ip eigrp topology
$. !.1<show ip eigrp interfaces
D. !.1<show ip eigrp neigbors
nswer' D
(44. 8ou are the $%O at !est.ing. !he networ" administrator has
left the company une-pectedly. !est.ing is e-periencing problems
with its Internet connection. 8ou retrie+e the following
interconnection diagram from the e;uipment room.
#ased on the diagram) what type of Internet connection could
!est.ing ha+e? 0$hoose two1
. DS9
#. Frame *elay
$. ISD/
D. Dedicated !1
%. Wireless
F. PO!S
nswer' #)D
(46.
8ou are the networ" administrator at !est.ing. 8ou ha+e attempted
to !elnet from the console port on !est.ing1 to 16(.1.(.35 but
failed. 8ou can ping 16(.1.(.35 successfully. What is the
probable cause of this problem? 0$hoose two1
. PPP authentication configuration problem.
#. misconfigured IP address or subnet mas"
$. n access control list
D. defecti+e serial cable.
%. /o cloc" rate on interface s: on !est.ing(
F. missing +ty password.
nswer' $)F
(6:. 8ou are the networ" administrator at !est.ing. !he routing
table on a !est.ing router is shown in the following graphic'
!he router recei+es an IP pac"et with a source IP address of
16(.134.(1,.(: and a destination address of 16(.134.((.7.
What will the router do with this pac"et?
. It will encapsulate the pac"et as Frame *elay and forward it
out of interface Serial :@:.112.
#. It will drop the pac"et and send an I$GP Destination
Bnreachable message out interface Fast%thernet :@:.
$. It will forward the pac"et out of interface Serial :@1 and
send an I$GP %cho *eply message out of interface Serial :@:.1:(.
D. It will encapsulate the pac"et to an P* frame and forward it
out of Fast%thernet :@:.
nswer' #
(6(. 8our newly appointed !est.ing trainee wants to "now what
re;uirements must be met before you can configure the D9/
trun"ing protocol to communicate D9/ information between two
switches.
What will your reply be?0choose (1
. 8ou must set each end of the trun" line to I%%% 4:(.1e
encapsulation.
#. 8ou must set the same D!P management domain name on both
switches.
$. 8ou must set all ports on the two switches as access ports.
D. 8ou must configure one of the switches as a D!P ser+er.
%. 8ou must use a rollo+er cable to connect the two switches.
F. 8ou must use a router to forward D!P traffic between D9/s.
nswer' #)D
(67. 8ou are the networ" administrator at !est.ing.com. !he
!est.ing networ" uses *IP as its routing protocol. portion of
the !est.ing networ" is shown in the following e-hibit'
8ou want to create a gateway of last resort.
What command should you issue?
. !est.ing10config1< ip route 12(.13.,.( :.:.:.: :.:.:.:
#. !est.ing10config1< ip route :.:.:.: :.:.:.: S1
$. !est.ing10config1< ip route 12(.13.,.1 :.:.:.: :.:.:.:
D. !est.ing10config1< ip route S: :.:.:.: :.:.:.:
%. !est.ing10config1< ip route :.:.:.: :.:.:.: 12(.13.,.(
nswer' %
(6,. 8our newly appointed !est.ing trainee wants to "now which
W/ encapsulations can be configured on an asynchronous serial
connection.
What will your reply be?
. PPP and !G
#. PPP and SD9$
$. !G and CD9$
D. SD9$ and CD9$
nswer'
(65. 8our !est.ing trainee wants to "now which D9/s are allowed
o+er a new trun" lin" that is configured on an IOS based switch.
What will your reply be?
. ll defined D9/s are allowed on the trun" by default.
#. %ach D9/) or D9/ range) that is specified with the
switchport mode command.
$. %ach D9/) or D9/ range) that is specified with the +tp
domain command.
D. %ach D9/) or D9/ range) that is specified with the +lan
database command.
nswer'
(63. 8ou are the networ" administrator at !est.ing. 8ou want to
configure a default route to any destination not found in the
routing table. What command should you use?
. *outer0config1< ip default=route :.:.:.: (55.(55.(55.(55 s:
#. *outer0config1< ip route :.:.:.: (55.(55.(55.(55 s:
$. *outer0config1< ip default=route :.:.:.: :.:.:.: s:
D. *outer0config1< ip route :.:.:.: :.:.:.: s:
%. *outer0config1< ip route any any e:
nswer' D
(62. 8ou are the networ" administrator at !est.ing. 8ou are as"ed
to pro+ide an ISD/ W/ lin" for the !est.ing networ". modular
$isco router with ( serial connections and a #*I@B interface is
the only a+ailable router. 8ou want to adapt this router for the
ISD/ connection.
What should you do?
. Do nothing. !he router is already suitable.
#. Purchase and install a #*I W/ interface in the router.
$. Purchase an e-ternal /!1 to terminate the local loop.
D. Purchase and install a !@/!1 de+ice on the router.
nswer'
(66. 8our !est.ing trainee Sandra as"s you what is the decimal)
base 1:) +alue of the binary number 1:11::11.
What should you tell her?
. 61
#. 155
$. 126
D. 14:
%. (:1
F. ((2
nswer' $
7::. 8our boss) !ess .ing) is curious about %I&*P route
information. She as"s you which %I&*P route information are held
in *G and maintained through the use of hello and update
pac"ets.
What should you tell !ess? 0Select two.1
. /eighbor !able
#. S*F !able
$. *!P !able
D. !opology !able
%. Iuey !able
F. Dual !able
nswer' )D
7:1. s technician at !est.ing.com you are re;uired to pro+ide
the subnetwor" address for a host with the IP address
(:1.1::.5.34@(4.
. (:1.1::.5.:
#. (:1.1::.5.7(
$. (:1.1::.5.3,
D. (:1.1::.5.35
%. (:1.1::.5.71
F. (:1.1::.5.1
nswer' $
7:(. 8our boss at !est.ing.com as"s you which routing protocols
that supports D9SG.
What should you tell her? 0Select three1
. IP
#. *IP+1
$. %I&*P
D. OSPF
%. I&*P
F. *IP+(
nswer' $)D)F
7:7. 8our boss at !est.ing.com as"s you which routing protocols
that supports D9SG.
What should you tell her? 0Select three1
. *IP+1
#. I&*P
$. %I&*P
D. OSPF
%. IS=IS
F. $DP+(
nswer' $)D)%
7:,. s technician at !est.ing.com you are re;uired to pro+ide
the subnetwor" number for a host with the IP address
12(.13.(1:.:@((.
. 12(.13.,(.:
#. 12(.13.1:2.:
$. 12(.13.(:4.:
D. 12(.13.(5(.:
%. 12(.13.(5,.:
nswer' $
7:5. 8ou wor" as a networ" consultant. 8ou are re;uired to design
a $isco networ" for !est.ing.com) a large company. !est.ing has
the following re;uirements on the networ"'
U minimal bandwidth for routing updates should be used
U ;uic" con+erging
U support D9SG) $ID*) IP) and IPM.
What routing protocol should you suggest?
. *IP+1
#. *IP+(
$. I&*P
D. OSPF
%. %I&*P
nswer' %
7:3. bandwidth 3,
8ou wor" as a technician at !est.ing.com. 8ou ha+e an OSPF
interface configured with the command
displayed in the e-hibit. What is the calculated OSPF cost of
this lin"?
. 1
#. 1:
$. 153(
D. 3,:::
%. 1(4:::
nswer' $
711. 8our boss at !est.ing.com is interested in the concept of
OSPF routing areas.
What are the characteristics of OSPF areas? 0$hoose three.1
. %ach OSPF area re;uires a loopbac" interface to be configured.
#. reas may be assigned any number from : to 35575.
$. rea : is called the bac"bone area.
D. Cierarchical OSPF networ"s do not re;uire multiple areas.
%. Gultiple OSPF areas must connect to area :.
F. Single area OSPF networ"s must be configured in area 1.
nswer' #)$)%
71(. One of the !est.ing.com trainees assigned to you want to
"now which ser+ices use BDP. What can you tell him? 0Select three
options.1
. D/S
#. !elnet
$. SG!P
D. S/GP
%. C!!P
F. !F!P
nswer' )D)F
71,. What Functions do router perform in a networ"? 0$hoose two1.
. Pac"et Switching
#. ccess 9ayer Security
$. Path Selection.
D. D9/ Gembership ssignment.
%. #ridging between 9/ segments.
F. Gicrosegmentation of #roadcast Domains.
nswer' )$
713. 8our boss at !est.ing.com is concerned about 9/ traffic
congestion.
What could cause this congestion? 0$hoose 71
. !oo many hosts in a broadcast domain
#. Full duple- operation
$. #roadcast storms
D. Gulticasting
%. Segmentation
F. 9ow bandwidth
nswer' )$)D
712. 8ou wor" as a networ" technician at !est.ing.com.
$isco router has been recei+ed from another !est.ing.com
di+ision. fter connecting to the console of the router) you
disco+er that the router has a configuration from a pre+ious
deployment.What should be done before a new configuration in
entered in the router?
. *G should be erases and the router restarted.
#. Flash should be erased and the router restarted.
$. /D*G should be erased and the router restarted.
D. !he new configuration should be entered and sa+ed.
nswer' D
714. What can you tell the $%O of !est.ing.com about ad+antages
of using D9/s? 0Select three options.1
. !hey increase the siJe of collision domains
#. !hey allow logical grouping of users by function.
$. !hey can enhance networ" security.
D. !hey increase the siJe of broadcast while decreasing the
number of collision domains.
%. !hey increase the number of broadcast domains while decreasing
the siJe of the broadcast domains.
F. !hey simplify switch administration.
nswer' #)$)%
714. !ess .ing wor" as a networ" administrator at !est.ing.com.
!ess is configuring a catalyst switch with D9/ information that
must be automatically distributed to other catalyst switches in
the networ".
What conditions must be met in order for the D9/s configured on
the other switches? 0$hoose three.1
. !he switch that will share the D9/ information must be in the
D!P Ser+er mode.
#. !he switches must be in the same D!P domain.
$. !he switch that will share the D9/ information must be
configured as root bridge.
D. !he switches must be configured to use the same D!P +ersion.
%. !he switches must be configured to use the same S!P +ersion.
F. !he switches must be configured to use the same type of ID
tagging.
nswer' )#)F
716. /etwor" topology e-hibit'
8ou wor" as a networ" administrator at !est.ing.com.
Cost !est.ing has established a connection with the
!est.ingSer+er C!!P ser+er attached to
interface %: of the !est.ing( router.
Which of the following statements describe the information
contained in protocol data units sent from host !est.ing to
!est.ingSer+er. 0$hoose three.1
. !he destination port number in a segment header will ha+e a
uni;ue +alue of 4:.
#. !he destination port number in a segment header will ha+e a
uni;ue +alue greater than or e;ual to 1:(7.
$. !he destination address of a frame will be the Gac address of
the C!!P ser+er interface.
D. !he destination address of a frame will be the Gac address of
the %: interface of the abc router.
%. !he destination address of a pac"et will be the IP address of
the %: interface of the abc router.
F. !he destination address of a pac"et will be the IP address of
the networ" interface of the C!!P Ser+er.
nswer' )D)F
7(:. /etwor" topology e-hibit'
Which destination addresses will be used by !est.ing to send
data to !est.ing$? 0$hoose two.1
. !he IP address of Switch !est.ing(
#. !he G$ address of Switch !est.ing(
$. !he IP address of !est.ing$
D. !he G$ address of !est.ing$
%. !he IP address of the route !est.ing1Qs %: interface.
F. !he Gac address of the router !est.ing1Qs %: interface.
nswer' $)F
7(1. /etwor" !opology %-hibit'
Dr. Sandra .ing wor"s as a networ" administrator at !est.ing.com.
She manages two routers named
!est.ing1 and !est"ing(. !hese two routers are connected by their
serial interfaces as illustrated in the networ" topology e-hibit)
but there is no connecti+ity between them. !he !est.ing1 router
is "nown to ha+e a correct configuration.
&i+en the Partial configurations) Grs .ing is re;uired to
identify the problem on the !est.ing router that is causing the
lac" of connecti+ity. 0Select 11
. !ransmission Bnit siJe too large
#. /o loopbac" set.
$. an incorrect subnet mas".
D. incompatible encapsulation at each end.
%. an incorrect IP address.
F. incompatible bandwidth between routers.
nswer' %
7(,. !est.ing trainee is curios about IS9 and 4:(.1; Frame
!agging) and as"s you what is the purpose of these.
What should you tell the !est.ing trainee?
. !hey Pro+ide #est Path Determination.
#. !hey llow the %-change of filtering tables.
$. !hey Specify different Implementations of the Spanning=!raa
Protocol.
D. !hey Pro+ide Interswitch D9/ $ommunication.
nswer' D
7(5. /etwor" !opology %-hibit'
n ccess 9ist has been designed to pre+ent C!!P traffic from the
Production Department from
reaching the C* ser+er ttached to the !est.ing( *outer. Which of
the following access lists will
accomplish this tas" when lists will accomplish this tas" when
grouped with the e: interface on the !est.ing1 *outer?
. Permit ip any any
Deny tcp 12(.13.13.: :.:.:.(55 12(.12.12.(5( :.:.:.: e; 4:
#. Permit ip any any
Deny tcp 12(.12.12.(5( :.:.:.: 12(.13.13.: :.:.:.(55 e; 4:
$. Deny tcp 12(.12.12.(5( :.:.:.: 12(.13.13.: :.:.:.(55 e; 4:
Permit ip any any
D. Deny tcp 12(.13.13.: :.:.:.(55 12(.12.12.(5( :.:.:.: e; 4:
Permit ip any any
nswer' D
7(3. In the implementation of D9SG techni;ues on a networ" using
a Single $lass $ IP address) which subnet mas" is the most
efficient for point=to=point serial lin"?1
. (55.(55.(55.:
#. (55.(55.(55.(,:
$. (55.(55.(55.(,4
D. (55.(55.(55.(5(
%. (55.(55.(55.(5,
nswer' D
7(2. /etwor" !opology %-hibit'
n ccess 9ist has been designed to pre+ent !elnet traffic from
the &raphics Department from reaching the Web Ser+er ttached to
the !est.ing7 *outer. On Which Interface and in what direction
should the access list be placed to most efficiently implement
this list?0$hoose !hree1
. !est.ing1 *outer
#. !est.ing7 *outer
$. s:
D. e:
%. in
F. out
nswer' )D)%
7(4. /etwor" !opology %-hibit'
8ou wor" as a networ" technician at !est.ing.com. It has become
necessary to pre+ent ccounting
Department Bsers on the !est.ing1 *outer from accessing the Cuman
*esources Ser+er attached to
interface %: of the !est.ing( *outer. !he following access
control list has been created.
access=list 16 deny 16(.134.13.1(4 :.:.:.71
access=list 16 permit any
On Which Interface and in which direction should the access list
be placed to pre+ent accounting users
from accessing the networ" attached to the %: interface of the
!est.ing( *outer? ccess to other
networ" should be unaffected.
. !est.ing1 S:) out.
#. !est.ing1 %1) in.
$. !est.ing1 %1) out.
D. !est.ing( S1) in.
%. !est.ing( %:) out.
F. !est.ing( %:) in.
nswer' %
77:. /etwor" !opology %-hibit'
8ou wor" as a networ" administrator at !est.ing.com.
Which of the following ccess 9ist statements are necessary to
allow F!P access to the C* ser+er from the Internet while
bloc"ing all other traffic.0Select two1.
. ccess=list 1:1 Permit tcp any 16(.134.,,.(5( :.:.:.: e; (1
#. ccess=list 1:1 Permit tcp any 16(.134.,,.(5( :.:.:.: e; (:
$. ccess=list 1:1 Permit tcp 16(.134.,,.(5( :.:.:.: any e; (:
D. ccess=list 1:1 Permit tcp 16(.134.,,.(5( :.:.:.: any e; (1
%. ccess=list 1:1 Deny tcp any 16(.134.,,.(55 :.:.:.: gt (1
F. ccess=list 1:1 Permit tcp 16(.134.,,.(55 :.:.:.: any gt (1
nswer' )#
771. 8ou are the networ" administrator at !est.ing.com. !he
internal !est.ing networ" is shown in the following e-hibit'
With regard to the IP addressing information in the e-hibit)
which interface will *outer # use to forward
an IP datagram to a host with an IP address of 1:.1:.1:.1:?
. S:
#. %:
$. %1
D. %(
nswer' #
777. With regard to Positi+e c"nowledgment and *etransmission
0P*1) which of the following are true? 0$hoose 7.1
. !he source de+ice will only retransmit lost pac"ets on the
re;uest of the destination de+ice.
#. !he source de+ice starts a timer when it sends a segment and
retransmits if an ac"nowledgment is not recei+ed before the timer
e-pires.
$. !he destination de+ice ac"nowledges receipt of a segment by
sending a pac"et with a new se;uence number and the $. bit sent.
D. !he destination de+ice ac"nowledges receipt of a segment by
sending a pac"et that indicates the ne-t se;uence number it
e-pects.
%. If the destination de+ice does not recei+e a segment) all
segments are retransmitted.
F. !he source de+ice "eeps a record of all segments sent and
e-pects and ac"nowledgment of each.
nswer' #)D)F
775. 8our boss at !est.ing.com is curios about the e-tended ping
command.
Which of the following statements are true? 0$hoose 7.1
. !he e-tended ping command is supported from user %M%$ mode.
#. !he e-tended ping command is supported from pri+ileged %M%$
mode.
$. With the e-tended ping command you can specify the port to be
pinged.
D. With the e-tended ping command you can specify the timeout.
%. With the e-tended ping command you can specify the datagram
siJe.
nswer' #)D)%
773. 8ou wor" as a technician at !est.ing. 8ou configure router
on the !est.ing networ" but you cannot ping the serial port of
the neighboring router. 8ou issue the show running=config
command. !he output from this command displays the word
KshutdownL for the serial interface. 8ou issue the show interface
s: command.
Which of the following lines would you e-pect to be displayed in
the output?
. Serial : is up) line protocol is up
#. Serial : is up) line protocol is down
$. Serial : is down) line protocol is down
D. Serial : is down) line protocol is up
%. Serial : is administrati+ely down) line protocol is down
F. Serial : is administrati+ely down) line protocol is up
nswer' %
772. 8ou wor" as networ" administrator at !est.ing. 8ou are
configuring a $isco router for the !est.ing networ". 8ou want to
apply an access control list on an interface of the router.
What command should you use?
. permit access=list 1:1 out
#. ip access=group 1:1 out
$. apply access=list 1:1 out
D. access=class 1:1 out
%. ip access=list e: out
nswer' #
774. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee) Fernanda is unsure of the distinction between
routed and routing protocols.
Cow would you e-plain the distinction to her? 0$hoose (.1
. routing protocol is assigned to an interface and determines
the method of pac"et deli+ery.
#. routed protocol is assigned to an interface and determines
the method of pac"et deli+ery.
$. routing protocol determines the path of a pac"et through a
networ".
D. routed protocol determines the path of a pac"et through a
networ".
%. routing protocol operates at the transport layer of the OSI
model.
F. routed protocol updates the routing table of a router.
nswer' #)$
776. 8ou wor" as a networ" administrator at !est.ing. 8ou install
a new host on the !est.ing networ". 8ou want to +erify the
configuration of the new host by establishing an F!P connection
to a remote ser+er. 8ou !est.ing trainee wants to "now what the
highest layer of the protocol stac" is that you are using for
this operation. What would your reply be?
. pplication
#. Presentation
$. Session
D. !ransport
%. Internet
F. Data 9in"
&. Physical
nswer'
7,:. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what the differences between half=
duple- %thernet and full=duple- %thernet are.
What should you tell her? 0$hoose (.1
. Calf=duple- %thernet operates in a shared collision domain.
#. Full=duple- %thernet has a lower effecti+e throughput.
$. Calf=duple- %thernet operates in a pri+ate collision domain.
D. Full=duple- %thernet allows two=way communication.
%. Calf=duple- %thernet operates in a pri+ate broadcast domain.
nswer' )D
7,1. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now which
command will show the 9GI traffic statistics. What would your
reply be?
. Show interface lmi
#. Show frame=relay lmi
$. Show interface frame=relay
D. Debug frame=relay interface.
nswer' #
7,(. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now which
command will set the bandwidth of serial : to 53"bps.
What would your reply be?
. #andwidth 53:::
#. #andwidth 53::::::
$. #andwidth 53
D. #andwidth 53"bps
nswer' $
7,7. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now which 9/ switch method holds the
pac"et in memory until the data portion of the pac"et reaches the
switch. What would your reply be?
. $ut=through
#. Store and forward
$. Frag=free
D. /one of the abo+e
nswer' $
7,,. What is the most common layer ( de+ice?
. Cub
#. #ridge
$. Switch
D. *outer
nswer' $
7,5. What is used to find the hardware address of a de+ice on a
9/?
. In+erse=*P
#. *e+erse=*P
$. Interior=*P
D. *P
nswer' D
7,3. What are the two most common re;uest@reply pair with I$GP
messages when using the ping
command?
. %cho re;uest and %cho reply
#. I$GP hold and I$GP send
$. I$GP re;uest and I$GP reply
D. %cho off and %cho on
nswer'
7,2. What do you call it when a frame is placed into another type
of frame?
. Framing
#. De=encapsulation
$. %ncapsulation
D. De=framing
nswer' $
7,4. Which technology is used by $atalyst switches to resol+e
topology loops and ensure data flows
properly though a single networ" path?
. D!P
#. IS9
$. 4:(.1I
D. S!P
nswer' D
7,6. Which command displays all the commands in the history
buffer?
. Show history
#. Show buffers
$. Show typed commands
D. Show terminal buffer
nswer'
75:. What does IP standard access lists filter on?
. !he source and destination addresses
#. !he destination port number
$. !he destination address
D. !he source address
nswer' D
751. When enabling %I&*P routing) what parameters must you apply?
. broadcast address) and S number
#. networ" number and S number
$. eigrp routing) networ" number) and passi+e interface
D. eigrp routing) networ" number) and S
nswer' D
75(. What is a connection protocol at the Cost to Cost layer?
. *P
#. **P
$. !$P
D. BDP
%. IP
F. I$GP
&. #ootP
nswer' $
757. I&*P sends a complete routing table to its neighbors how
often by default?
. e+ery 5 minutes
#. e+ery 6: seconds
$. e+ery 3: seconds
D. e+ery 7: seconds
nswer' #
75,. Which networ" mas" should you place on a $lass $ networ" to
accommodate a user re;uirement of ten subnetwor"s?
. (55.(55.(55.16(
#. (55.(55.(55.((,
$. (55.(55.(55.(,:
D. (55.(55.(55.(,4
nswer' $
755. What is the ma-imum distance of 1:#ase!?
. 1:: meters
#. 1:: yards
$. (:: meters
D. (:: yards
nswer'
753. Which of the following is not a distance=+ector routing
protocol?
. *IP
#. IPM *IP
$. I&*P
D. OSPF
nswer' D
752. Which of the following layers from the !$P@IP model
corresponds to the networ" layer in the OSI Godel?
. pplication
#. Internet
$. !ransport
D. /etwor"
%. Data 9in"
nswer' #
754. 8ou are a technician at !est.ing. 8ou are considering the
pros and cons of a connectionless ser+ice. Which of the following
are characteristics of a connectionless ser+ice? 0Select !wo1
. *eliable
#. /on=reliable
$. 9ess bandwidth=intensi+e
D. Candsha"ing
nswer' #)$
756. Which of the following OSI layers is used to determine the
best path to a networ"?
. Data 9in"
#. Session
$. Physical
D. Presentation
%. /etwor"
F. !ransport
nswer' %
73:. 8ou are a technician at !est.ing. 8ou are wor"ing within the
$isco IOS. Which of the following functions does the up arrow "ey
pro+ide?
. *ecalls the pre+ious command line
#. Go+es the cursor one line up
$. *edisplays the current command line
D. $apitaliJes the command line
nswer'
73(. Which of the following statements regarding routed and
routing protocols are true?
0Select ( choices1
. routed protocol is assigned to an interface and determines
the method of pac"et deli+ery
#. routing protocol determines the path of the pac"et through a
networ"
$. routed protocol determines the path of the pac"et through a
networ"
D. routing protocol operates at the transport layer of the OSI
model
%. routed protocol updates the routing table of a router
nswer' )#
737. When powering up a router) which of the following types of
memory normally stores the start=up
configuration?
. *G
#. *OG
$. F9SC
D. /D*G
nswer' D
73,. #ased on the debug output shown) what type of handsha"e
occurred for PPP authentication?
<debug ppp authentication
ppp serial1' Send $CP challenge idR7, to remote
ppp serial1' $CP challenge from P1*(
ppp serial1' $CP response recei+ed from P1*(
ppp serial1' $CP response idR7, recei+ed from P1*(
ppp serial1' Send $CP success idR7, to remote
ppp serial1' *emote passed $CP authentication
ppp serial1' Passed $CP authentication
ppp serial1' Passed $CP authentication with remote
. one=way
#. two=way
$. three=way
D. no handsha"es re;uired during authentication
nswer' $
735. Which of the following commands will send and recei+e I$GP
echo messages to +erify connecti+ity from host to host?
. ping
#. tracert
$. netstat
D. show cdp neighbors detail
%. show ip route
F. traceroute
nswer'
732. 8ou are a networ" technician at !est.ing. 8ou ha+e Fust
finished configuring a router on the !est.ing networ". !he
changes ha+e been successfully entered and e+erything is wor"ing
properly.
8ou then sa+e your changes and reboot the router. /one of your
changes are acti+e after the reboot. Cowe+er) when you loo" at
the contents of the startup config) your changes are there.
Which of the following indicates the source of the problem?
. Cardware failure in /D*G pre+ents the router from loading the
config
#. Startup=config in flash is corrupt and cannot be analyJed
$. *outer configuration=register set to bypass startup
configuration
D. Startup=config in /D*G is corrupt and cannot be analyJed
nswer' $
734. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what the word KanyL mean in the
following e-tended access list statement'
ccess=list 1:1 permit tcp any 16(.134.1:.: :.:.:.(55 e; tcp
What would your reply be?
. chec" any of the bits in the source address
#. permit any wildcard mas" for the address
$. accept any source address
D. chec" any bit in the destination address
%. permit (55.(55.(55.(55 :.:.:.:
F. accept any destination
nswer' $
72:. In Frame *elay) what are D9$Is used for?
. !hey determine the Frame *elay encapsulation type
#. !hey identify the logical circuit between a local router and a
Frame *elay W/ switch
$. !hey represent the "eepali+es used to maintain the PD$ in an
acti+e state
D. !hey represent the physical address of the router attached to
a Frame *elay networ"
nswer' #
721. Which of the following W/ ser+ices uses two data lin" layer
encapsulations) one for data and one for signaling?
. ISD/
#. Frame *elay
$. !G
D. FDDI
nswer'
72(. Which of the following statements is true in regards to
Frame *elay Gultipoint subinterfaces?
. n ip address is re;uired on the physical interface
#. ll routers are re;uired to be fully meshed
$. ll routers must be in the same subnet to forward routing
updates and broadcasts
D. Gultipoint is the default configuration for Frame *elay
subinterfaces
nswer' $
727. 8ou are a technician at !est.ing. 8ou ha+e Fust connected a
new host to a wor"group switch on the !est.ing networ". !he new
hostQs 9ayer 7 configuration is correct. Cowe+er) the host is
unable to access the ser+er resources in its networ" segment.
Which of the following is most li"ely causing the problem?
. !he router lac"s a routing table entry for the new host
#. !he host switch port is assigned to the incorrect D9/
$. !he host G$ address is incorrectly configured
D. DIP instance for the new host has not been initialiJed
nswer' #
72,. Which of the following is the decimal and he-adecimal
e;ui+alent of this binary number 1:1:1:1:?
. DecimalR13:) he-idecimalR::
#. DecimalR12:) he-idecimalR
$. DecimalR14:) he-idecimalR##
D. DecimalR16:) he-idecinalR$$
nswer' #
723. 8ou are the networ" administrator at !est.ing.com.
!est.ing.com has a switched networ". 8ou need to add a new D9/)
named Debits) to the networ". Which of the following are true
regarding configuration of this +lan? 0$hoose 71
. !he D9/ must be created
#. !he D9/ must named
$. n IP address must be configured for the $$OB/!S D9/
D. !he desired ports must be added to the new D9/
%. !he D9/ must be added to the S!P Domain
nswer' )#)D
722. Which of the following commands should be used to display
*IP routing updates as they are sent and recei+ed by the router?
. Show ip protocols
#. Show ip route rip
$. Debug ip rip
D. Debug ip updates
%. Debug ip transactions
nswer' $
724. 8ou are the networ" administrator at !est.ing.com. 8ou ha+e
Fust configured a new router that you attached to the !est.ing
networ". 8ou ping the directly connected serial port of the
directly neighboring router. !he ping is unsuccessful.
!he show running=config output displays the word KshutdownL for
the serial interface.
Which of the following lines will be displayed in the show
interface s: output?
. Serial : is up) line protocol is down
#. Serial : is down) line protocol is down
$. Serial : is down) line protocol is up
D. Serial : is administrati+ely down) line protocol is down
%. Serial : is administrati+ely down) line protocol is up
F. Serial : is administrati+ely up) line protocol is down
nswer' D
74:. Which of the following bit patterns is for a $lass #
address?
. :-------
#. 1:------
$. 11:-----
D. 111:----
%. 1111:---
nswer' #
74(. Which symbol in the router prompt indicates you are in the
pri+ileged mode?
. N
#. <
$. ?
D. V
nswer' #

747. 8ou are a technician at !est.ing. 8our newly appointed
!est.ing trainee wants to "now what the binary
+alue for 12( is. What would your reply be?
. 1::1::1:
#. 1::11::1
$. 1:1:11::
D. 1:1::11:
%. 111:::11
nswer' $
7,,. In the following is the G$ address of your /I$'
$6=7F=7(=#,=D$=16
What is the OBI portion e-pressed in binary format?
. 11::11::=::111111=:::11:::
#. 11:::11:=11::::::=:::11111
$. 11::111:=:::11111=:11:::::
D. 11::1::1=::111111=::11::1:
%. 11::11::=:1111:::=:::11:::
F. 11111:::=:11::111=:::11::1
nswer' D
7,2. In the router IOS binary image file name c2(::=aFs,:=m-)
what does c2(:: represent?
. !he memory capacity re;uirements
#. !he hardware product platform
$. !he distribution channel
D. !he feature capabilities
%. !he run location and compression status
nswer' #
7,6. 8ou are the networ" administrator at !est.ing.com. 8ou want
to telnet to a router on the !est.ing
networ") howe+er) the connection is denied. 8ou +erify
connecti+ity to the router by pinging the router
successfully. 8ou need to enter a set of commands on the remote
router to allow !elnet connecti+ity.
Which commands should you use?
. router0config1< line con :
router0config=line1< password welcome
router0config=line1< login
#. router0config1< line au- : ,
router0config=line1< password welcome
router0config=line1< login
$. router0config1< line +ty : ,
router0config=line1< password welcome
router0config=line1< login
D. router0config1< line tty : ,
router0config=line1< password welcome
router0config=line1< enable login
nswer' $
75:. 8ou are the networ" administrator at !est.ing. 8our
assistant made a number of errors when utiliJing
the router setup mode facility. 8ou want to e-it setup mode
without applying the changes that your
assistant made.
What should you do?
. !ype e-it at the setup dialog.
#. !ype close at the setup dialog.
$. Press the $trl=$ "ey combination.
D. Press the $trl=M "ey combination.
%. Issue the copy startup=config command.
F. Issue the write erase command.
nswer' $
751. !he abo+e graphic represents the result of an attempt to
open a !elnet connection to router $$%SS1
from router *emote(2.
Which of the following command se;uences will address this
problem correctly?
. $$%SS10config1< line console :
$$%SS10config=line1< password cisco
#. *emote(20config1< line console :
*emote(20config=line1< login
*emote(20config=line1< password cisco
$. *emote(20config1< line +ty : ,
*emote(20config=line1< login
*emote(20config=line1< password cisco
D. $$%SS10config1< line +ty : ,
$$%SS10config=line1< login
$$%SS(0config=line1< password cisco
%. $$%SS10config1< enable password cisco
F. *emote(20config1< enable password cisco
nswer' D
757. *efer to the topology and configuration shown in the
graphic.
Which of the following IOS commands are necessary to configure
switch port 1 to establish a lin" with
router !est"ing1 as shown? 0$hoose three options.1
. Switch0config1< interface fastethernet :@1
#. Switch0config=if1< switchport mode access
$. Switch0config=if1< switchport mode trun"
D. Switch0config=if1< switchport access +lan 1
%. Switch0config=if1< switchport trun" encapsulation isl
F. Switch0config=if1< switchport trun" encapsulation dot1;
nswer' ) $) F
75,. !he new !est.ing trainee technicianwants to "now which which
networ" type will OSPF establish router
adFacencies but not perform the D*@#D* election process. What
will your reply be?
. Point=to=point
#. #roadcast multicast
$. /onbroadcast multicast
D. #ac"bone area :
%. /one of the abo+e
nswer'
755. n internetwor" has been configured as shown in the diagram)
with both routers using %I&*P routing
for S ,,. Bsers on the #ranch router can not reach any of the
subnets on the CI router.
Which of the following commands will fi- this problem?
. #ranch0config=router1< +ersion (
#. #ranch0config=router1< no auto=summary
$. #ranch0config=router1< redistribute eigrp ,,
D. #ranch0config=router1< eigrp log=neighbor=changes
%. #ranch0config=router1< default=information originate
nswer' #
754. networ" administrator has been re;uested to ensure that
only the ser+er is allowed to connect to port
Fa:@1 on a $atalyst switch. !he ser+er is plugged into the switch
Fa:@1 port and ready to be brought
online.
What can the administrator do to ensure that only the G$ address
of the ser+er is allowed by switch
port Fa:@1? 0$hoose two options.1
. $onfigure port Fa:@1 to accept connections only from the
static IP address of the ser+er.
#. %mploy a proprietary connector type on Fa:@1 that is
incompatible with other host connectors.
$. $onfigure the G$ address of the ser+er as a static entry
associated with port Fa:@1.
D. #ind the IP address of the ser+er to its G$ address on the
switch to pre+ent other hosts from spoofing
the ser+er IP address.
%. $onfigure port security on Fa:@1 to reFect traffic with a
source G$ address other than that of the
ser+er.
F. $onfigure an access list on the switch to deny ser+er traffic
from entering any port other than Fa:@1.
nswer' $) %
731. What will be the conse;uence in an e+ent where two $isco 9/
switches are connected with a single
crosso+er cable?
. !he switch port lin" lights will be off on both switches
indicating the ports are not connected.
#. !he switch port lin" light will be off on one switch
indicating that S!P has disabled the port.
$. !he switch port lin" lights will flash amber indicating an
error.
D. !he switch port lin" lights will be green indicating normal
operation.
nswer' D
73(. Study the e-hibit below carefully'
*efer to the diagram. ll hosts ha+e connecti+ity with one
another.
Which of the statements below describe the addressing scheme
utiliJed in the networ"? 0$hoose three
options.1
. !he subnet mas" in use is (55.(55.(55.16(.
#. !he subnet mas" in use is (55.(55.(55.1(4.
$. !he IP address 12(.13.1.(5 can be assigned to hosts in D9/1.
D. !he IP address 12(.13.1.(:5 can be assigned to hosts in D9/1.
%. !he 9/ interface of the router is configured with one IP
address.
F. !he 9/ interface of the router is configured with multiple IP
addresses.
nswer' #) $) F
737. Study the e-hibit below carefully'
*efer to the diagram.
Which of the following statements describes the router port
configuration and the switch port
configuration as shown in the topology? 0$hoose three options.1
. !he !est"ing1 W/ port is configured as a trun"ing port.
#. !he !est"ing1 port connected to Switch1 is configured using
subinterfaces.
$. !he !est"ing1 port connected to Switch1 is configured as 1:
Gbps.
D. !he Switch1 port connected to !est"ing1 is configured as a
trun"ing port.
%. !he Switch1 port connected to Cost # is configured as an
access port.
F. !he switch1 port connected to Cub1 is configured as full
duple-.
nswer' #) D) %
73,. In what location are %I&*P successor routes stored?
. In the routing table only.
#. In the neighbor table only.
$. In the topology table only.
D. In the routing table and neighbor table.
%. In the routing table and topology table.
F. In the topology table and neighbor table.
nswer' %
735. Which protocol will you ad+ice the new !est.ing trainee
technician to use in order to minimiJe
administrati+e o+erhead in a switched networ" by allowing the
configuration of a new D9/ to be
distributed to all the switched in a domain?
. S!P
#. &D*P
$. S/GP
D. D!P
%. DC$P
nswer' D
732. Study the e-hibit below carefully'
*efer to the networ" shown in the graphic.
!he !est.ing trainee technician wants to "now which access list
statement will pre+ent hosts in the range
of networ"s from 16(.134.13:.: to 16(.134.161.: from access to
the ser+er and not affect access by hosts
from the 16(.134.165.: networ"? 0!he access list will be placed
on the Come router Fa: interface.1 What
will your reply be?
. access=list 1 deny 16(.134.137.: :.:.:.(55
#. access=list 1 deny 16(.134.1(4.: :.:.1(2.(55
$. access=list 1 deny 16(.134.155.: :.:.(55.(55
D. access=list 1 deny 16(.134.: :.:.71.(55
nswer' D
734. !est"ing< show running=config
Psome output te-t omittedN
router rip
networ" 1:.:.:.:
T
ip classless
!est"ing< show ip route
Psome output te-t omittedN
&ateway of last resort is 1:.1.(.( to networ" :.:.:.:
1:.:.:.:@(, is subnetted) ( subnets
* 1:.1.7.: ?1(:@1A +ia 1:.1.(.() ::'::'::) Serial:@:
$ 1:.1.(.: is directly connected) Serial:@:
$ 1:.1.5.: is directly connected) Serial:@1
$ 1:.1.3.: is directly connected) Fast%thernet:@:
*V :.:.:.:@: ?1(:@1A +ia 1:.1.5.5) ::'::'::) Serial:@1
*eferring to the output of the two show commands in the graphic
abo+e' Cow will the I$P pac"ets be
processed by !est"ing if an administrator wants to ping host
1:.1.4.5 from host 1:.1.3.1::?
. !he pac"ets will be discarded.
#. !he pac"ets will be routed out the S:@: interface.
$. !he pac"ets will be routed out the S:@1 interface.
D. !he pac"ets will be routed out the Fa:@: interface.
%. !he pac"ets will be routed through the 1:.1.(.( gateway.
nswer' $
72:. Which configuration command must be in effect to allow the
use of eight subnets if the subnet mas" is
(55.(55.(55.((, when a new internetwor" is being implemented with
a single $lass $ networ" address?
. *outer0config1< ip classless
#. *outer0config1< ip subnet=Jero
$. *outer0config1< ip +ersion 3
D. *outer0config1< no ip classful
%. *outer0config1< ip unnumbered
F. *outer0config1< ip all=nets
nswer' #
721. Which of the following statements regarding %I&*P successor
routes is +alid? 0$hoose two options.1
. successor route is used by %I&*P to forward traffic to
destination.
#. Successor routes are sa+ed in the topology table to be used if
the primary route fails.
$. Successor routes are flagged as Kacti+eL in the routing table.
D. successor route may be bac"ed up by a feasible successor
route.
%. Successor routes are stored in the neighbor table following
the disco+ery process.
nswer' ) D
726. 8ou are the networ" administrator at !est.ing. !est.ing has
been assigned the IP address 146.33.1.: by
its Internet Ser+ice Pro+ider. 8our newly appointed !est.ing
trainee wants to "now how many hosts will
be supported on each subnet if you di+ide the networ" by using
the (55.(55.(55.((, subnet mas".
What would your reply be?
. 1,
#. 13
$. 7:
D. 7(
%. 3(
F. 3,
nswer' $

Potrebbero piacerti anche