Sei sulla pagina 1di 138

NETWORK IN GALGOTIAS UNIVERSITY

Commands
Router vc

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname VC
VC(config)#interface Serial1/0
VC(config-if)#no ip address
VC(config-if)#ip address 200.1.1.1
255.255.255.0
VC(config)#interface Serial1/1
VC(config-if)#no ip address
VC(config-if)#ip address 200.2.2.2
255.255.255.0
VC(config)#interface Serial1/2
VC(config-if)#no ip address
VC(config-if)#ip address 200.3.3.3
255.255.255.0
VC(config)#interface Serial1/3
VC(config-if)#no ip address
VC(config-if)#ip address 200.4.4.4
255.255.255.0
VC(config)#interface FastEthernet0/0
VC(config-if)#no ip address
VC(config-if)#ip address 201.1.1.1
255.255.255.0
VC(config)#router rip
VC(config-router)#network 200.1.1.0
VC(config-router)#network 200.2.2.0
VC(config-router)#network 200.3.3.0
VC(config-router)#network 200.4.4.0
VC(config-router)#network 200.5.5.0
VC(config-router)#network 201.1.1.0
VC(config)#interface Serial1/0
VC(config-if)#clock rate 64000
VC(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on
Interface Serial1/0, changed state to up
Router pro vc
Router(config)#hostname "pro vc"
pro vc(config)#interface Serial0/0/0
pro vc(config-if)#no ip address
pro vc(config-if)#ip address 200.1.1.6
255.255.255.0
pro vc(config)#interface FastEthernet0/1
pro vc(config-if)#no ip address
pro vc(config-if)#ip address 1.1.1.1
255.0.0.0
pro vc(config)#interface FastEthernet0/0
pro vc(config-if)#ip address 150.1.1.1
255.255.0.0
pro vc(config)#router rip
pro vc(config-router)#
pro vc(config-router)#exit
pro vc(config)#router rip
pro vc(config-router)#network 200.1.1.0
pro vc(config-router)#network 1.0.0.0
pro vc(config-router)#network 150.1.0.0
router SCHOOL OF ENGINEERING &
TECHNOLOGY
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname
% Incomplete command.
Router(config)#
Router(config)#hostname "SCHOOL OF
ENGINEERING & TECHNOLOGY"
SCHOOL OF ENGINEERING &
TECHNOLOGY(config)#interface
FastEthernet0/0
SCHOOL OF ENGINEERING &
TECHNOLOGY(config-if)#no ip address
SCHOOL OF ENGINEERING &
TECHNOLOGY(config-if)#ip address
150.1.1.1 255.255.0.0
SCHOOL OF ENGINEERING &
TECHNOLOGY(config)#interface
FastEthernet0/1
SCHOOL OF ENGINEERING &
TECHNOLOGY(config-if)#no ip address
SCHOOL OF ENGINEERING &
TECHNOLOGY(config-if)#ip address
170.1.1.1 255.255.0.0
SCHOOL OF ENGINEERING &
TECHNOLOGY(config)#router rip
SCHOOL OF ENGINEERING &
TECHNOL(config-router)#network 150.1.0.0
SCHOOL OF ENGINEERING &
TECHNOL(config-router)#network 170.1.0.0

Router business administration

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

Router(config-if)#
Router(config-if)#end
Router#c
%SYS-5-CONFIG_I: Configured from console
by console
onfigure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "business
administration"
business administration(config)#interface
FastEthernet0/0
business administration(config-if)#ip
address 150.1.1.2 255.255.0.0business
administration(config)#interface
FastEthernet0/1
business administration(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

business administration(config-if)#no ip
address
business administration(config-if)#ip
address 170.1.1.2 255.255.0.0
business administration(config)#router rip
business administration(config-
router)#network 150.1.0.0
business administration(config-
router)#network 170.1.0.0
router finance & commerce
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "finance &
commerce"
finance & commerce(config)#interface
FastEthernet0/0
finance & commerce(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

finance & commerce(config-if)#ip address
150.1.1.3 255.255.0.0
finance & commerce(config)#interface
FastEthernet0/1
finance & commerce(config-if)#ip address
170.1.1.3 255.255.0.0
finance & commerce(config)#router rip
finance & commerce(config-
router)#network 150.1.0.0
finance & commerce(config-
router)#network 170.1.0.0


router humanties & social sciences
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "humanties
&social sciences"
humanties &social
sciences(config)#interface FastEthernet0/0
humanties &social sciences(config-if)#ip
address 150.1.1.4 255.255.0.0
humanties &social sciences(config-if)#
humanties &social sciences(config-if)#exit
humanties &social
sciences(config)#interface FastEthernet0/1
humanties &social sciences(config-if)#
humanties &social sciences(config-if)#exit
humanties &social
sciences(config)#interface FastEthernet0/0
humanties &social sciences(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

humanties &social sciences(config-if)#
humanties &social sciences(config-if)#exit
humanties &social
sciences(config)#interface FastEthernet0/1
humanties &social sciences(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

humanties &social sciences(config-if)#ip
address 170.1.1.4 255.255.0.0
humanties &social sciences(config)#router
rip
humanties &social sciences(config-
router)#network 150.1.0.0
humanties &social sciences(config-
router)#network 170.1.0.0
router basic & applied sciences
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "basic & applied
sciences"
basic & applied sciences(config)#
basic & applied sciences(config)#interface
FastEthernet0/0
basic & applied sciences(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

basic & applied sciences(config-if)#ip
address 150.1.1.5 255.255.0.0
basic & applied sciences(config-if)#
basic & applied sciences(config-if)#exit
basic & applied sciences(config)#interface
FastEthernet0/1
basic & applied sciences(config-if)#no
shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

basic & applied sciences(config-if)#ip
address 170.1.1.5 255.255.0.0
basic & applied sciences(config)#router rip
basic & applied sciences(config-
router)#network 150.1.0.0
basic & applied sciences(config-
router)#network 170.1.0.0
router arch
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname
% Incomplete command.
Router(config)#
Router(config)#hostname arch
arch(config)#
arch(config)#interface FastEthernet0/0
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

arch(config-if)#ip address 150.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#interface FastEthernet0/1
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

arch(config-if)#ip address 150.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#router rip
arch(config-router)#network 150.1.0.0
arch(config-router)#network 170.1.0.0
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname
% Incomplete command.
Router(config)#
Router(config)#hostname arch
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname
% Incomplete command.
Router(config)#
Router(config)#hostname arch
arch(config)#
arch(config)#interface FastEthernet0/0
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

arch(config-if)#ip address 150.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#interface FastEthernet0/1
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

arch(config-if)#ip address 170.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#router rip
arch(config-router)#network 150.1.0.0
arch(config-router)#network 170.1.0.0
arch(config)#
arch(config)#interface FastEthernet0/0
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

arch(config-if)#ip address 150.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#interface FastEthernet0/1
arch(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

arch(config-if)#ip address 170.1.1.6
255.255.0.0
arch(config-if)#
arch(config-if)#exit
arch(config)#router rip
arch(config-router)#network 150.1.0.0
arch(config-router)#network 170.1.0.0
router medical
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname medical
medical(config)#
medical(config)#interface FastEthernet0/0
medical(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

medical(config-if)#ip address 150.1.1.7
255.255.0.0
medical(config-if)#
medical(config-if)#exit
medical(config)#interface FastEthernet0/1
medical(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

medical(config-if)#ip address 170.1.1.7
255.255.0.0
medical(config-if)#
medical(config-if)#exit
medical(config)#router rip
medical(config-router)#network 150.1.0.0
medical(config-router)#network 170.1.0.0
router nursing
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname nursing
nursing(config)#
nursing(config)#interface FastEthernet0/0
nursing(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

nursing(config-if)#ip address 150.1.1.8
255.255.0.0
nursing(config-if)#ip address 10.1.1.8
255.255.0.0
nursing(config-if)#no ip address
nursing(config-if)#ip address 150.1.1.8
255.255.0.0
nursing(config-if)#
nursing(config-if)#exit
nursing(config)#interface FastEthernet0/1
nursing(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

nursing(config-if)#ip address 170.1.1.8
255.255.0.0
nursing(config-if)#
nursing(config-if)#exit
nursing(config)#router rip
nursing(config-router)#network 150.1.0.0
nursing(config-router)#network 170.1.0.0
router media
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname media
media(config)#
media(config)#interface FastEthernet0/0
media(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

media(config-if)#ip address 150.1.1.9
255.255.0.0
media(config-if)#
media(config-if)#exit
media(config)#interface FastEthernet0/1
media(config-if)#ip address 170.1.1.9
255.255.0.0
media(config-if)#
media(config-if)#exit
media(config)#router rip
media(config-router)#network 150.1.0.0
media(config-router)#network 170.1.0.0
router cse dean



Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "cse dean"
cse dean(config)#
cse dean(config)#interface FastEthernet0/0
cse dean(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

cse dean(config-if)#ip address 140.1.1.1
255.255.0.0
cse dean(config)#router rip
cse dean(config-router)#network 140.1.0.0
cse dean(config)#interface Serial0/0/0
cse dean(config-if)#no shutdown
cse dean(config-if)#ip address 130.1.1.1
255.255.0.0
cse dean(config-if)#
cse dean(config-if)#exit
cse dean(config)#router rip
cse dean(config-router)#network 130.1.0.0
router ece
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "ece dean"
ece dean(config)#
ece dean(config)#interface FastEthernet0/0
ece dean(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ece dean(config-if)#ip address 140.1.1.2
255.255.0.0
ece dean(config-if)#
ece dean(config-if)#exit
ece dean(config)#interface Serial0/1/0
ece dean(config-if)#no shutdown
ece dean(config-if)#ip address 130.1.1.2
255.255.0.0
ece dean(config-if)#
ece dean(config-if)#exit
ece dean(config)#router rip
ece dean(config-router)#network 140.1.0.0
ece dean(config-router)#network 130.1.0.0
router civil&mec

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "civil&mec dean"
civil&mec dean(config)#
civil&mec dean(config)#interface
FastEthernet0/0
civil&mec dean(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

civil&mec dean(config-if)#ip address
140.1.1.3 255.255.0.0
civil&mec dean(config-if)#
civil&mec dean(config-if)#exit
civil&mec dean(config)#interface
Serial0/1/0
civil&mec dean(config-if)#no shutdown
civil&mec dean(config-if)#no ip address
civil&mec dean(config-if)#no ip address
civil&mec dean(config-if)#ip address
130.1.1.3 255.255.0.0
civil&mec dean(config-if)#
civil&mec dean(config-if)#exit
civil&mec dean(config)#router rip
civil&mec dean(config-router)#network
140.1.0.0
civil&mec dean(config-router)#network
130.1.0.0
router cse hod
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "cse hod"
cse hod(config)#
cse hod(config)#interface Serial0/1/0
cse hod(config-if)#no shutdown
cse hod(config-if)#ip address 155.1.1.1
255.255.0.0
cse hod(config-if)#
cse hod(config-if)#exit
cse hod(config)#interface FastEthernet0/0
cse hod(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

cse hod(config-if)#ip address 160.1.1.1
255.255.0.0
cse hod(config-if)#
cse hod(config-if)#exit
cse hod(config)#router rip
cse hod(config-router)#network 140.1.0.0
cse hod(config-router)#network 130.1.0.0
cse dean(config)#interface Serial0/1/0
cse dean(config-if)#ip address 130.1.1.1
255.255.0.0
cse dean(config-if)#
%LINK-5-CHANGED: Interface Serial0/1/0,
changed state to up
no shutdown

router ece hod
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "ece hod"
ece hod(config)#
ece hod(config)#interface Serial0/1/0
ece hod(config-if)#
%LINK-5-CHANGED: Interface Serial0/1/0,
changed state to up
no shutdown
ece hod(config-if)#ip address 160.1.1.1
255.255.0.0
ece hod(config-if)#no ip address
ece hod(config-if)#ip address 160.1.1.2
255.255.0.0
ece hod(config-if)#
ece hod(config-if)#exit
ece hod(config)#interface FastEthernet0/0
ece hod(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ece hod(config-if)#ip address 155.1.1.2
255.255.0.0
ece hod(config-if)#
ece hod(config-if)#exit
ece hod(config)#router rip
ece hod(config-router)#network 160.1.0.0
ece hod(config-router)#network 155.1.0.0
router civil&mec hod

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface Serial0/1/0
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/1/0,
changed state to up
no shutdown
Router(config-if)#ip address 155.1.1.3
255.255.0.0
Router(config-if)#
Router(config-if)#end
Router#c
%SYS-5-CONFIG_I: Configured from console
by console
onfigure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "civil&mec hod"
civil&mec hod(config)#
civil&mec hod(config)#interface
FastEthernet0/0
civil&mec hod(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

civil&mec hod(config-if)#ip address
160.1.1.3 255.255.0.0
civil&mec hod(config-if)#
civil&mec hod(config-if)#exit
civil&mec hod(config)#router rip
civil&mec hod(config-router)#network
160.1.0.0
civil&mec hod(config-router)#network
155.1.0.0
router comp app
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "comp app"
comp app(config)#
comp app(config)#interface
FastEthernet0/0
comp app(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

comp app(config-if)#
comp app(config-if)#exit
comp app(config)#interface
FastEthernet0/0
comp app(config-if)#ip address 165.1.1.1
255.255.0.0
comp app(config-if)#
comp app(config-if)#exit
comp app(config)#interface
FastEthernet0/1
comp app(config-if)#ip address 166.1.1.1
255.255.0.0
comp app(config-if)#
comp app(config-if)#exit
comp app(config)#router rip
comp app(config-router)#network 166.1.0.0
comp app(config-router)#network 165.1.0.0
router cse
cse>enable
cse#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
cse(config)#
cse(config)#
cse(config)#hostname
% Incomplete command.
cse(config)#
cse(config)#
cse(config)#interface FastEthernet0/0
cse(config-if)#ip address 165.1.1.2
255.255.0.0
cse(config-if)#
cse(config-if)#exit
cse(config)#interface FastEthernet0/1
cse(config-if)#ip address 166.1.1.2
255.255.0.0
cse(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

cse(config-if)#
cse(config-if)#exit
cse(config)#router rip
cse(config-router)#network 166.1.0.0
cse(config-router)#network 165.1.0.0
router bioinfo
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname bioinfo
bioinfo(config)#
bioinfo(config)#interface FastEthernet0/0
bioinfo(config-if)#
bioinfo(config-if)#exit
bioinfo(config)#interface FastEthernet0/0
bioinfo(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

bioinfo(config-if)#ip address 165.1.1.3
255.255.0.0
bioinfo(config-if)#
bioinfo(config-if)#exit
bioinfo(config)#interface FastEthernet0/1
bioinfo(config-if)#ip address 166.1.1.3
255.255.0.0
bioinfo(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

bioinfo(config-if)#
bioinfo(config-if)#exit
bioinfo(config)#interface FastEthernet0/0
bioinfo(config-if)#
bioinfo(config-if)#exit
bioinfo(config)#router rip
bioinfo(config-router)#network 165.1.0.0
bioinfo(config-router)#network 166.1.0.0
router ece
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname ece
ece(config)#
ece(config)#interface FastEthernet0/0
ece(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ece(config-if)#no ip address
ece(config-if)#ip address 180.1.1.1
255.255.0.0
ece(config-if)#
ece(config-if)#exit
ece(config)#interface FastEthernet0/1
ece(config-if)#
ece(config-if)#exit
ece(config)#interface FastEthernet0/0
ece(config-if)#
ece(config-if)#exit
ece(config)#interface FastEthernet0/1
ece(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

ece(config-if)#ip address 181.1.1.2
255.255.0.0
ece(config-if)#
ece(config-if)#exit
ece(config)#router rip
ece(config-router)#network 180.1.0.0
ece(config-router)#network 181.1.0.0
router ee
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname ee
ee(config)#
ee(config)#interface FastEthernet0/0
ee(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ee(config-if)#ip address 180.1.1.2
255.255.0.0
ee(config-if)#
ee(config-if)#exit
ee(config)#interface FastEthernet0/1
ee(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

ee(config-if)#ip address 181.1.1.1
255.255.0.0
ee(config-if)#
ee(config-if)#exit
ee(config)#router rip
ee(config-router)#network 180.1.0.0
ee(config-router)#network 181.1.0.0
router eee
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname ee
ee(config)#
ee(config)#interface FastEthernet0/0
ee(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ee(config-if)#ip address 180.1.1.3
255.255.0.0
ee(config-if)#
ee(config-if)#exit
ee(config)#interface FastEthernet0/1
ee(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

ee(config-if)#ip address 181.1.1.3
255.255.0.0
ee(config-if)#
ee(config-if)#exit
ee(config)#router rip
ee(config-router)#network 180.1.0.0
ee(config-router)#network 181.1.0.0
router civil
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname civil
civil(config)#
civil(config)#interface FastEthernet0/0
civil(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

civil(config-if)#ip address 175.1.1.1
255.255.0.0
civil(config-if)#
civil(config-if)#exit
civil(config)#interface FastEthernet0/1
civil(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

civil(config-if)#ip address 176.1.1.1
255.255.0.0
civil(config-if)#
civil(config-if)#exit
civil(config)#router rip
civil(config-router)#network 175.1.0.0
civil(config-router)#network 176.1.0.0
router mec
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname mec
mec(config)#
mec(config)#interface FastEthernet0/0
mec(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

mec(config-if)#ip address 175.1.1.2
255.255.0.0
mec(config-if)#
mec(config-if)#exit
mec(config)#interface FastEthernet0/1
mec(config-if)#ip address 176.1.1.2
255.255.0.0
mec(config-if)#
mec(config-if)#exit
mec(config)#interface FastEthernet0/0
mec(config-if)#
mec(config-if)#exit
mec(config)#router rip
mec(config-router)#network 175.1.0.0
mec(config-router)#network 176.1.0.0
router Microsoft
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname microsoft
microsoft(config)#
microsoft(config)#interface Serial0/0/0
microsoft(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to up
no shutdown
microsoft(config-if)#sh
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to administratively down
utdown
microsoft(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to up
no shutdown
microsoft(config-if)#ip address 100.1.1.1
255.0.0.0
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface Serial0/0/1
microsoft(config-if)#no shutdown
microsoft(config-if)#ip address 110.1.1.1
255.0.0.0
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface FastEthernet0/0
microsoft(config-if)#no shutdown


%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up
microsoft(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up
ip address 202.1.1.1 255.255.255.0
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface Serial0/0/0
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface FastEthernet0/1
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface FastEthernet0/0
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#interface Serial0/0/1
microsoft(config-if)#
microsoft(config-if)#exit
microsoft(config)#router rip
microsoft(config-router)#network 100.0.0.0
microsoft(config-router)#network 110.0.0.0
microsoft(config-router)#network 202.1.1.0
microsoft(config)#interface Serial0/0/0
microsoft(config-if)#clock rate 64000
microsoft>en
microsoft#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
microsoft(config)#exit
microsoft#
%SYS-5-CONFIG_I: Configured from console
by console

microsoft#copy running-config tftp
Address or name of remote host []?
?Host name or address not specified

microsoft#
microsoft#copy running-config tftp :
^
% Invalid input detected at '^' marker.

microsoft#copy running-config tftp
Address or name of remote host []?
microsoft
Destination filename [microsoft-confg]?
microsoft info

Writing running-config...Translating
"microsoft"...
%Error opening tftp://microsoft/microsoft
info (Cannot resolve domain name)
microsoft#
microsoft#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
microsoft(config)#interface FastEthernet0/0
microsoft(config-if)#exit
microsoft(config)#exit
microsoft#
%SYS-5-CONFIG_I: Configured from console
by console

microsoft#copy running-config tftp
Address or name of remote host []?
microsoft
Destination filename [microsoft-confg]?
microsoft info

Writing running-config...Translating
"microsoft"...
%Error opening tftp://microsoft/microsoft
info (Cannot resolve domain name)
microsoft#copy running-config tftp
Address or name of remote host []?
microsoft
Destination filename [microsoft-confg]?
Microsoftinfo

telnet : microsoft#en
microsoft#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
microsoft(config)#line vty 0 3
microsoft(config-line)#password microsoft
microsoft(config-line)#login

Writing running-config...Translating
"microsoft"...
%Error opening
tftp://microsoft/microsoftinfo (Cannot
resolve domain name)
microsoft#copy running-config tftp
Address or name of remote host []?
microsoft
Destination filename [microsoft-confg]?
microsoftinfo

Writing running-config...Translating
"microsoft"...!!
[OK - 677 bytes]

677 bytes copied in 0.05 secs (13000
bytes/sec)
router 23
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

Router(config-if)#ip address 162.1.1.1
255.255.0.0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial0/0/0
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to up
no shutdown
Router(config-if)#ip address 110.1.1.2
255.0.0.0
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 162.1.0.0
Router(config-router)#network 110.0.0.0
Router job
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "job companies"
job companies(config)#
job companies(config)#interface Serial1/2
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/0
job companies(config-if)#
%LINK-5-CHANGED: Interface Serial1/0,
changed state to up
no shutdown
job companies(config-if)#ip address
210.1.1.1 255.255.255.0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/2
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/1
job companies(config-if)#no shutdown
job companies(config-if)#ip address
210.2.2.2 255.255.255.0
job companies(config-if)#
%LINK-5-CHANGED: Interface Serial1/1,
changed state to up

job companies(config-if)#exit
job companies(config)#interface
FastEthernet0/0
job companies(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

job companies(config-if)#ip address
220.1.1.2 255.255.255.0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#router rip
job companies(config-router)#
job companies(config-router)#exit
job companies(config)#interface
FastEthernet0/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface
FastEthernet0/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/1
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/1
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#router rip
job companies(config-router)#network
210.1.1.0
job companies(config-router)#network
220.1.1.0
job companies(config-router)#
job companies(config-router)#exit
job companies(config)#interface
FastEthernet0/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/0
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#interface Serial1/1
job companies(config-if)#
job companies(config-if)#exit
job companies(config)#router rip
job companies(config-router)#network
210.2.2.0
job companies(config)#interface Serial1/0
job companies(config-if)#clock rate 64000
job companies>enable
job companies#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
job companies(config)#router rip
job companies(config-router)#exit
job companies(config)#^Z
job companies#
%SYS-5-CONFIG_I: Configured from console
by console

job companies#copy running-config tftp
Address or name of remote host []? tcs
Destination filename [job companies-
confg]? tcsinfo

Writing running-config...Translating "tcs"...
%Error opening tftp://tcs/tcsinfo (Cannot
resolve domain name)
job companies#copy running-config tftp
Address or name of remote host []? tcs
Destination filename [job companies-
confg]? tcsinfo

Writing running-config...Translating
"tcs"...!!
[OK - 647 bytes]

647 bytes copied in 0.003 secs (215000
bytes/sec)
telnet:
job companies#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
job companies(config)#line vty 0 3
job companies(config-line)#password tcs
job companies(config-line)#login
router 30
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface Serial1/0
Router(config-if)#
%LINK-5-CHANGED: Interface Serial1/0,
changed state to up
no shutdown
Router(config-if)#ip address 210.2.2.3
255.255.255.0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

Router(config-if)#ip address 36.1.1.1
255.0.0.0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial1/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 36.0.0.0
Router(config-router)#
Router(config-router)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial1/0
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 210.2.2.0
Router hostel
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname hostel
hostel(config)#
hostel(config)#
hostel(config)#interface FastEthernet0/0
hostel(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

hostel(config-if)#ip address 172.1.1.1
255.255.0.0
hostel(config-if)#
hostel(config-if)#exit
hostel(config)#interface FastEthernet0/1
hostel(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

hostel(config-if)#ip address 172.2.2.2
255.255.0.0
hostel(config-if)#
hostel(config-if)#exit
hostel(config)#router rip
hostel(config-router)#network 172.1.0.0
hostel(config-router)#network 172.2.0.0
router finance
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname finance
finance(config)#
finance(config)#interface FastEthernet0/0
finance(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

finance(config-if)#ip address 174.1.1.1
255.255.0.0
finance(config-if)#
finance(config-if)#exit
finance(config)#interface FastEthernet0/1
finance(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

finance(config-if)#ip address 173.1.1.1
255.255.0.0
finance(config-if)#
finance(config-if)#exit
finance(config)#router rip
finance(config-router)#network 174.1.0.0
finance(config-router)#network 173.1.0.0
router hr
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname hr
hr(config)#
hr(config)#interface FastEthernet0/0
hr(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

hr(config-if)#ip address 132.1.1.1
255.255.0.0
hr(config-if)#
hr(config-if)#exit
hr(config)#interface FastEthernet0/1
hr(config-if)#ip address 133.1.1.1
255.255.0.0
hr(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

hr(config-if)#
hr(config-if)#exit
hr(config)#router rip
hr(config-router)#network 132.1.0.0
hr(config-router)#network 133.1.0.0
router controller of exam

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "controller of
exam"
controller of exam(config)#
controller of exam(config)#interface
FastEthernet0/0
controller of exam(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

controller of exam(config-if)#ip address
152.1.1.1 255.255.0.0
controller of exam(config-if)#
controller of exam(config-if)#exit
controller of exam(config)#interface
FastEthernet0/1
controller of exam(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

controller of exam(config-if)#ip address
153.1.1.1 255.255.0.0
controller of exam(config-if)#
controller of exam(config-if)#exit
controller of exam(config)#router rip
controller of exam(config-router)#network
152.1.0.0
controller of exam(config-router)#network
153.1.0.0
router ibm

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname ibm
ibm(config)#
ibm(config)#
ibm(config)#interface Serial0/0/0
ibm(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to up
no shutdown
ibm(config-if)#ip address 195.1.1.1
255.255.255.0
ibm(config-if)#
ibm(config-if)#exit
ibm(config)#interface Serial0/0/0
ibm(config-if)#
ibm(config-if)#exit
ibm(config)#interface Serial0/0/1
ibm(config-if)#no shutdown
ibm(config-if)#ip address 162.1.1.2
255.255.0.0
ibm(config-if)#
ibm(config-if)#exit
ibm(config)#interface FastEthernet0/0
ibm(config-if)#ip address 197.1.1.1
255.255.255.0
ibm(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

ibm(config-if)#
ibm(config-if)#exit
ibm(config)#router rip
ibm(config-router)#network 195.1.1.0
ibm(config-router)#network 162.1.0.0
ibm(config-router)#network 197.1.1.0
ibm>en
ibm#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
ibm(config)#^Z
ibm#
%SYS-5-CONFIG_I: Configured from console
by console

ibm#copy running-config tftp
Address or name of remote host []? ibm
Destination filename [ibm-confg]? ibminfo

Writing running-config...Translating "ibm"...
%Error opening tftp://ibm/ibminfo (Cannot
resolve domain name)
ibm#copy running-config tftp
Address or name of remote host []? ibm
Destination filename [ibm-confg]? ibminfo

Writing running-config...Translating
"ibm"...!!
[OK - 677 bytes]

677 bytes copied in 0.002 secs (338000
bytes/sec)

Ssh:
ibm#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
ibm(config)#ip domain-name ibm.com
ibm(config)#c
ibm(config)#cr
ibm(config)#crypto key ge
ibm(config)#crypto key generate rsa
ibm(config)#crypto key generate rsa ?
<cr>
ibm(config)#crypto key generate rsa
The name for the keys will be: ibm.ibm.com
Choose the size of the key modulus in the
range of 360 to 2048 for your
General Purpose Keys. Choosing a key
modulus greater than 512 may take
a few minutes.

How many bits in the modulus [512]: 512
% Generating 512 bit RSA keys, keys will be
non-exportable...[OK]

ibm(config)#line vty 0 3
*Mar 1 0:31:54.522: RSA key size needs to
be at least 768 bits for ssh version 2
*Mar 1 0:31:54.522: %SSH-5-ENABLED: SSH
1.5 has been enabled
ibm(config-line)#transport input ssh

router 21

Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

Router(config-if)#ip address 161.1.1.1
255.255.0.0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial0/0/0
Router(config-if)#ip address 162.1.1.1
255.255.0.0
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0,
changed state to up
no shutdown
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 161.1.0.0
Router(config-router)#network 162.1.0.0
Router oth uni
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#hostname "oth uni"
oth uni(config)#
oth uni(config)#interface FastEthernet0/0
oth uni(config-if)#ip address 222.1.1.1
255.255.255.0
oth uni(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/0
oth uni(config-if)#
%LINK-5-CHANGED: Interface Serial1/0,
changed state to up
no shutdown
oth uni(config-if)#ip address 223.1.1.1
255.255.255.0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/2
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#no shutdown
oth uni(config-if)#no ip address
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/2
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/3
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/3
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/4
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#no ip address
oth uni(config-if)#no ip address
oth uni(config-if)#ip address 221.1.1.1
255.255.255.0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface Serial1/0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#interface FastEthernet0/0
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#router rip
oth uni(config-router)#network 221.1.1.0
oth uni(config-router)#network 222.1.1.0
oth uni(config-router)#network 223.1.1.0
oth uni>enable
oth uni#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
oth uni(config)#router rip
oth uni(config-router)#
oth uni(config-router)#exit
oth uni(config)#interface Serial1/1
oth uni(config-if)#
oth uni(config-if)#exit
oth uni(config)#router rip
oth uni(config-router)#
oth uni(config-router)#exit
oth uni(config)#router rip
oth uni(config-router)#network 221.1.1.0
oth uni(config-router)#network 222.1.1.0
oth uni(config-router)#network 223.1.1.0
oth uni(config-router)#no network
221.1.0.0
oth uni(config-router)#no network
222.1.0.0
oth uni(config-router)#no network
223.1.0.0
oth uni(config-router)#network 223.1.0.0
oth uni(config-router)#no network
223.1.0.0
oth uni(config-router)#
oth uni(config-router)#^Z
oth uni#
%SYS-5-CONFIG_I: Configured from console
by console

oth uni#copy running-config tftp
Address or name of remote host []?
universites
Destination filename [oth uni-confg]?
universitesinfo

Writing running-config...Translating
"universites"...
%Error opening
tftp://universites/universitesinfo (Cannot
resolve domain name)
oth uni#copy running-config tftp
%LINEPROTO-5-UPDOWN: Line protocol on
Interface Serial1/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Serial1/1, changed state to up

Address or name of remote host []?
universites
Destination filename [oth uni-confg]?
universitesinfo

Writing running-config...Translating
"universites"...
%Error opening
tftp://universites/universitesinfo (Cannot
resolve domain name)
oth uni#copy running-config tftp
Address or name of remote host []?
universites
Destination filename [oth uni-confg]?
universitesinfo

Writing running-config...Translating
"universites"...
%Error opening
tftp://universites/universitesinfo (Cannot
resolve domain name)
oth uni#copy running-config tftp
Address or name of remote host []?
universites
Destination filename [oth uni-confg]?
universitesinfo

Writing running-config...Translating
"universites"...!!
[OK - 829 bytes]

829 bytes copied in 0.006 secs (138000
bytes/sec)
Ssh :


oth uni>
oth uni>en
oth uni#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
oth uni(config)#ip domain-name
universites.com
oth uni(config)#cr
oth uni(config)#crypto key ge
oth uni(config)#crypto key generate rsa
The name for the keys will be: oth
uni.universites.com
Choose the size of the key modulus in the
range of 360 to 2048 for your
General Purpose Keys. Choosing a key
modulus greater than 512 may take
a few minutes.

How many bits in the modulus [512]: 215
% A decimal number between 360 and 2048
How many bits in the modulus [512]: 512
% Generating 512 bit RSA keys, keys will be
non-exportable...[OK]

oth uni(config)#transport input ssh
*Mar 1 0:42:17.278: RSA key size needs to
be at least 768 bits for ssh version 2
*Mar 1 0:42:17.278: %SSH-5-ENABLED: SSH
1.5 has been enabled
^
% Invalid input detected at '^' marker.

router 29
Router>enable
Router#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to
up

Router(config-if)#ip address 141.1.1.1
255.255.0.0
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#
Router(config-router)#exit
Router(config)#router rip
Router(config-router)#network 141.1.0.0
Router(config-router)#
Router(config-router)#exit
Router(config)#interface Serial1/0
Router(config-if)#ip address 221.1.1.2
255.255.255.0
Router(config-if)#
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#network 221.1.1.0



switch 12
Switch>enable
Switch#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#vlan 2
Switch(config-vlan)#name microsoft
Switch(config-vlan)#exit
Switch(config)#interface vlan 2
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan2,
changed state to up

Switch(config-if)#ip address 162.1.1.2
255.255.0.0
Switch(config-if)#interface f0/0
%Invalid interface type and number
Switch(config)#interface f0/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 2

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Vlan2, changed state to up
Switch(config-if)#int f0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#int f0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#int f0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#int f0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#%IP-4-DUPADDR:
Duplicate address 162.1.1.2 on Vlan2,
sourced by 00D0.BC22.7264

Switch21
Switch>en
Switch#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#int range f0/1-4
Switch(config-if-range)#exit
Switch(config)#vlan 3
Switch(config-vlan)#name job
Switch(config-vlan)#exit
Switch(config)#int range f0/1-4
Switch(config-if-range)#switchport mode
access
Switch(config-if-range)#switchport access
vlan 3
Switch(config-if-range)#exit
Switch(config)#interface vlan 3

%LINK-5-CHANGED: Interface Vlan3,
changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Vlan3, changed state to up
Switch(config-if)#ip add 36.1.1.2
% Incomplete command.
Switch(config-if)#ip add 36.1.1.2 255.0.0.0

Switch 22

Switch>
Switch>en
Switch#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#int ran
Switch(config)#int range f
Switch(config)#int range fastEthernet 0/
%LINK-5-CHANGED: Interface
FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/1, changed state to
up

^
% Invalid input detected at '^' marker.

Switch(config)#
Switch(config)#int range fastEthernet 0/1-4
Switch(config-if-range)#exit
Switch(config)#vlan 4
Switch(config-vlan)#name oth uni
^
% Invalid input detected at '^' marker.

Switch(config-vlan)#name othuni
Switch(config-vlan)#exit
Switch(config)#int vlan 4
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan4,
changed state to up

Switch(config-if)#ip add 141.1
^
% Invalid input detected at '^' marker.

Switch(config-if)#ip add 141.1.1.2
255.255.0.0
Switch(config-if)#int range fastEthernet 0/1-
4
Switch(config-if-range)#switchport mode
access
Switch(config-if-range)#switchport access
vlan 4

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Vlan4, changed state to up

Switch 11
Switch>
Switch>en
Switch#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#vlan 5
Switch(config-vlan)#name ibm
Switch(config-vlan)#exit
Switch(config)#int vlan 5
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan5,
changed state to up

Switch(config-if)#ip add 161.1.1.2
255.255.0.0
Switch(config-if)#int range fast
Switch(config-if)#int range fast
Switch(config-if)#int range f
Switch(config-if)#int range fastethernet 0/1-
4
Switch(config-if-range)#switchport mode
access
Switch(config-if-range)#switchport access
vlan 5

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Vlan5, changed state to up
Switch(config-if-range)#
Switch schools
Switch>en
Switch#conf
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#vlan 7
Switch(config-vlan)#
Switch(config-vlan)# vlan 7
Switch(config-vlan)#no vlan 7
Switch(config)#vlan 6
Switch(config-vlan)#name 6
Switch(config-vlan)#exit
Switch(config)#
Switch(config)#int vlan 6
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan6,
changed state to up

Switch(config-if)#ip add 150.1.1.10
255.255.0.0
Switch(config-if)#int range f0/1-10
Switch(config-if-range)#switchport mode
access
Switch(config-if-range)#switchport access
vlan 6

%LINEPROTO-5-UPDOWN: Line protocol on
Interface Vlan6, changed state to up
Switch(config)#int range f0/1-11
Switch(config-if-range)#switchport access
vlan 6
Switch(config-if-range)#switchport mode
access
Switch(config-if-range)#switchport access
vlan 6
Switch#
%SYS-5-CONFIG_I: Configured from console
by console

Switch#copy running-config tftp
Address or name of remote host []? schools
Destination filename [Switch-confg]?
schoolsinfo

Writing running-config...Translating
"schools"...
%Error opening tftp://schools/schoolsinfo
(Cannot resolve domain name)
Switch#
Switch#configure terminal
Enter configuration commands, one per
line. End with CNTL/Z.
Switch(config)#interface FastEthernet0/11
Switch(config-if)#switchport access vlan
6^Z
Switch#
%SYS-5-CONFIG_I: Configured from console
by console

Switch#copy running-config tftp
Address or name of remote host []? schools
Destination filename [Switch-confg]?
schoolsinfo

Writing running-config...Translating
"schools"...!!
[OK - 1550 bytes]

1550 bytes copied in 0.006 secs (258000
bytes/sec)

Potrebbero piacerti anche