Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
- UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 1 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
This document illustrates how to connect a D700 Drive to the following:
FX3U PLC
GOT 1020/1030
Modbus master
E1000 as a Modbus master
The information in this document to based around software versions
GX Developer V8
GX IEC Developer V7
GT Designer 2 V2.77
E-Designer V7.4
For full communication details see the relevant manuals
FX3U PLC to inverter communication
FX3U Users Manual (Data Communication) 168594
GOT 1020/1030
GOT1000 Series Connection Manual SH/NA -08053
Modbus
FR-E700-EC (European version applied manual) ib0600336engb
Chapter 4.20.6
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 2 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
FX3U to D700
FX3U configuration
In GX Developer or GX IEC Developer enter the following in to the PLC
Parameters:
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 3 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
D700 Configuration
Enter the following parameters into the D700 drive
Parameter
Number
Name Set Value
160 Enable Parameters 0 -
79 Operation mode
selection
0 PU/EXT switch over mode
117 Station number 1 Set to Salve Station number
118 Communication speed 192 19200
119 Stop bit length 10 7 bits 1 stop
120 Parity check
presence/absence
2
With even parity check
121 Number of
communication retries
9999 Disabled, but can be used to stop drive if
comms failed
122 Communication check
time interval
9999 Disabled, but can be used to stop drive if
comms failed
123 Waiting time setting 9999 Disabled, but can be used to stop drive if
comms failed
124 CR, LF
presence/absence
selection
1
340 Link start mode
selection
1 Net mode
549 Mitsubishi or Modbus
Protocol
0 Mitsubishi
551* PU mode operation
command source
selection
9999 Parameter unit automatic recognition
Normally, operation panel is the command
source. When the parameter unit is
connected to the PU connector, PU is the
command source.
For PU operation the same as the E500 set Pr.551 = 2.
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 4 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Wiring
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 5 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
GOT configuration.
GOT Configuration
In GT Designer 2 enter the following in to the system environment
D700 Configuration
Enter the following parameters into the D700 drive
Parameter
Number
Name Set Value
160 Enable Parameters 0 -
79 Operation mode
selection
0 PU/EXT switch over mode
117 Station number 1 Set to Salve Station number
118 Communication speed 192 19200
119 Stop bit length 10 7 bits one stop
120 Parity check
presence/absence
1 CL
121 Number of
communication retries
9999 Disabled, but can be used to stop drive
if comms failed
122 Communication check
time interval
9999 Disabled, but can be used to stop drive
if comms failed
123 Waiting time setting 90 Disabled, but can be used to stop drive
if comms failed
124 CR, LF presence/absence
selection
1
340 Link start mode selection 1 Net mode
549 Mitsubishi or Modbus
Protocol
0 Mitsubishi
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 6 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Wiring
Photo of wiring a standard Ethernet cable from the RJ-45 PU port on the
inverter to the terminal strip on the GOT 1030
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 7 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Addressing
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 8 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 9 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Modbus
E1000 Settings
In E-Designer enter the following in to the HMI peripherals
D700 Configuration
Enter the following parameters into the D700 drive
Parameter
Number
Name Set Value
160 Enable Parameters 0 -
79 Operation mode selection 0 PU/EXT switch over mode
117 Station number 1 Set to Salve Station number
118 Communication speed 192 19200
119 Stop bit length 10 7 bits one stop
This setting has no effect using modbus
120 Parity check
presence/absence
2 CL
This setting has no effect using modbus
121 Number of
communication retries
9999 Disabled, but can be used to stop drive if
comms failed
122 Communication check
time interval
9999 Disabled, but can be used to stop drive if
comms failed
123 Waiting time setting 9999 Disabled, but can be used to stop drive if
comms failed
124 CR, LF presence/absence
selection
1 This setting has no effect using modbus
340 Link start mode selection 1 Net mode
549 Mitsubishi or Modbus
Protocol
1 Modbus
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 10 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Modbus protocol details
Drive parameter details
In this product, the inverter data are classified in the holding register area,
register addresses 40001 to 49999.
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 11 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Modbus registers
System environment variable
Real time monitor
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 12 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Parameters
Errors
Issued by: Mitsubishi Electric Europe B.V. - UK Branch
Document issue: Ver August 2008
Produced by : - CTC
Travellers Lane, Hatfield, Herts, AL10 8XB, UK
Author: Barry Weller
Databank - Technical Bulletin
Title: Ethernet comms between Qn and FX3U Page 13 of 13
Keywords: Qn, QJ71E71
Ethernet
FX3U, FX3U-ENET
Wiring
Point-to-Point
The RS422 port on the operator terminal is connected to the PU port on the
FR-A/F/E/D frequency inverter system or to the RJ45 port on the FR-S500
inverter system with the standard cable CAB9.
The RS232 port on the operator terminal is connected to the PU port on the
FR-A/F/E/D frequency inverter system or to the RJ45 port on the FR-S500
inverter system with the standard cable SC-FR-PC.