0 valutazioniIl 0% ha trovato utile questo documento (0 voti)
45 visualizzazioni4 pagine
Binary input board 23BE22 is used for the isolated input of up to 16 binary process signals. The board is especially used for counter inputs up to 8 kHz Scanning and processing of the inputs are executed with the high time resolution of 1 ms.
Binary input board 23BE22 is used for the isolated input of up to 16 binary process signals. The board is especially used for counter inputs up to 8 kHz Scanning and processing of the inputs are executed with the high time resolution of 1 ms.
Binary input board 23BE22 is used for the isolated input of up to 16 binary process signals. The board is especially used for counter inputs up to 8 kHz Scanning and processing of the inputs are executed with the high time resolution of 1 ms.
ABB Utilities GmbH 19 Doc.-No.: 1KGT 150 524 V000 1 Data Sheet Binary Input 23BE22 Application The binary input board 23BE22 is used for the iso- lated input of up to 16 binary process signals. The board is especially used for counter inputs up to 8 kHz Scanning and processing of the inputs are ex- ecuted with the high time resolution of 1 ms. Alloca- tion of an input to a processing function can be done according to the rules of configuration. The board 23BE22 can process the following types of signals: V 16 single indications with time stamp V 8 double indications with time stamp V 2 digital measured values each with 8 bit V 1 digital measured value with 16 bit V 16 pulse counters Characteristics Eight inputs each form a group with a common return. The 16 inputs form two groups. The inputs are potentially isolated by means of opto-couplers. The board allows process signal voltages from 24 to 60 VDC. The input circuit is dimensionedin that way, that current regulative diodes keepthe signal current constant. The board has sixteen light emitting diodes to indi- cate the signal-state. The LEDs are organized in two columns on the front plate. The LED follows directly the input. The maximum permissible frequency for counter pulses is 8 kHz. Binary input board 23BE22 E01 W01 E02 E08 E07 E06 E05 E04 E03 W02 E16 E15 E14 E13 E12 E11 E10 E09 I I D E V I D E R Fig. 1: Block diagram B U S M O D U L E The binary input board 23BE22 can execute the fol- lowingprocessingfunctions for the different types of signals: V Digital filtering to suppress contact bounce V Suppression of technologically caused chattering signals V Intermediate position suppression and monitoring for double indications ABB Utilities GmbH RTU560 Data Sheet Binary Input 23BE22 20 Doc.-No.: 1KGT 150 524 V000 1 V Consistency check for all binary input chan- nels allocated to digital measured values V Summation of increment pulses to form counter values in 31 bit counter value registers V Relocation of count values into other relo- cation registers on request The effective functionality of the board depends on the executed firmware version. The selection of the requested firmware version for RTU560 stations is done by a jumper on the 23BE22 board. The 23BE22 board has a buffer which allows the temporary storage of 50 time-stamped event messages in chronological order designated for transmission to the communication unit. The microcontroller on the board processes all time -critical tasks of the parameterized processing func- tions. Moreover it carries out the interactive commu- nication with the RTU560 system bus. All configura- tion data and processing parameters are loaded fromthe communication unit via the RTU560 system bus. The board is equipped with both a serial and a paral- lel interface to the RTU560 system bus. During initialization and operation the board carries out a number of tests. If a fault occurs it is reportedto the communication unit. All fault conditions impair- ing the function of the board are displayed as com- mon fault signal with a light emitting diode (ST) on the front panel. A failure of the board is detected by the communication unit. RTU560 Data Sheet Binary Input 23BE22 ABB Utilities GmbH Doc.-No.: 1KGT 150 524 V000 1 21 Technical Data In addition to the RTU560 general technical data, the following applies: Input Channels Inputs: 16, in 2 groups of 8 with common return per group Input voltage: 24, 48, 60 V DC -20 %...+15 % log. 0: -3 V...+9 V log. 1: +18 V...+75 V Maximum -75 V...-3 V max. 1 min. input voltage: +75 V...+120 V max. 1 min. (IEC 870-3) Input current: typically 2 mA for 24 to 60 V DC Power Supply Supply: 5 V / 230 mA Mechanical Layout Printed circuit 3HE, Euro-card format board: (160 x 100 mm) Front panel: 4R, 1 slot (20 mm) Weight: approx. 0.2 kg Connection Type Connector: indirect, 48 pole Type F DIN 41612 Test Voltages AC test voltage: 2.5 kV 50 Hz / VDE 804 safety electrical isolation Impulse voltage 5 kV (1.2/50) withstand test: IEC 255-4 (class III) Electromagnetic Compatibility Electrical fast 1 kV transient test: IEC 801-4 (class 2) High frequency 2.5 kV (1MHz) disturbance test: IEC 255-4 (class III) Environmental Conditions Temperature: 0 ... 70 _C Relative humidity: 5 ... 95% (non condensing) Ordering Information Front plate plastic: light beige 23BE22R5012 1 KGT 009 800 R5001 ABB Utilities GmbH RTU560 Data Sheet Binary Input 23BE22 22 Doc.-No.: 1KGT 150 524 V000 1 ABB Utilities GmbH 68309 Mannheim (Germany) Telephone +49 (0) 621 381-7592 Telefax +49 (0) 621 381-7622 06/2002 Subject to alteration