Tank capacity 120 cum mm Angle of repose 30 Degree = 17.00 kN/m 3 Conrete M 20 = #### N/m 3 Steel fy 415 N/mm 2 Tensile stess = 150 N/mm 2 scbc 7 N/mm 2 m = 13 Nominal cover 35 mm = 9.81 N/mm 3 1 Solution, general:- There are four components of design. (I) Design of long wall (II) Design of short wall (III) Design of roof slab (IV) Design of base slab The design of walls will be done under two condition. (a) Tank full with water, with no earth fill out side. (b) Tank empty, with full earth pressure due to saturated earth fill. 2 Design Constants:- For HYSD Bars = 20 s st = 150 N/mm 2 = N/mm 2 s cbc = 7 N/mm 2 m = 13 j=1-k/3 = = R=1/2xc x j x k = = 3 Design of Long wall :- (a) Tank empty with pressure satureted soil from outside. P a = K a Y'H +Y w H 1 - sin 30 1 + sin 30 Cutailment of reinfocrement. Since B.M. is proportional to h 3 , we have: A sth h 3 A sth 1/3 A st H 3 A st Direct compression in long walls:- The earth pressure acting on short walls will cause compression in long walls, because top portion of shorts walls act as slab supported on long walls At h = 3.00 / 4 = 0.75 or 1.00 m above the base of walls . = This direct compression devloped on long walls and wall section. This will be well taken by distribution steel and wall section unit wt. of water Cocrete M wt. of concrete 25000 3.00 120000 Saturated soil unit wt unit weight Here, K a = = k= m*c = x 0.333 0.378 m*c+sst 0.874 1.155 The base slab will be designed for uplift pressure and the hole tank is to be tasted against floatation. As the L/B ratio is greater than 2 the long wall will be designed as cantilever. The bottom one metre ( >H /4) of short walls will be designed as cantilever while the top portion will designed as slab supported by long walls . P a =K a Y' (H-h) + Y w (H-h) P LC =P a .x B/2 = = From which h = H H B Q=DISCHRAGE IN CUMEC MANNING'S COEFF FOR CONCRETE N=0.014 V=VELOCITY IN M/S A=AREA OF CROSS SECTION OF DRAIN P=PERIMETER OF DRAIN=2D+B R=A/P S=LONGITUDINAL SLOPE, GENERALLY 1IN 500 TO 1IN 750 Drain dia Area(sq.cm)Spacing Perimeter No wt/m L 10 0.7854 200 c/s 3.5 6 21 0.6165 12.947 8 0.5027 200 L 1 19 19 0.3946 7.4971 8 0.5027 200 L 1 19 19 0.3946 7.4971 2 1 3 2 1 S R N A Q = 10 0.7854 250 c/s 3.5 5 17.5 0.6165 10.789 38.731 kgs Cover Slab Total Weight= 3600 X 38.73= 139.43 MT dia Area(sq.cm) 8 0.5027 200 c/s 1 6 6 0.3946 2.3675 8 0.5027 200 L 1 6 6 0.3946 2.3675 8 0.5027 200 c/s 1 6 6 0.3946 2.3675 8 0.5027 200 L 1 6 6 0.3946 2.3675 9.47 Total Weight= 3600 X 9.47= 34.092 MT Total quantity of steel=Dtrain+Cover Slab= 173.52 MT