Sei sulla pagina 1di 13

Nokia Flexi WBTS IP commissioning settings

BTS ID

(FSME + FTLB + FXDA1 + FRGP2)

BTS name

MGH4999

BTS location

Mghira testbed

BTS description

2+2+2, 20W

BTS IP addresses:
Subnet address

10.209.0.0

Subnet mask

255.255.255.248 / 29

TRS address

10.209.0.1

BTS address

10.209.0.2

DHCP client address range

10.209.0.3 10.209.0.6

RNC address

10.207.19.132

NTP address

10.207.19.135

LDAP server

Not in use

Certificate management

Not in use

TLS for OAM interface

Probing

BTS firewall

Ping and traceroute enabled

FTP server on FTM

Enabled

TRS settings

Physical layer configuration:

FTM type

FTLB

Transport mode

Iub IP

Interface type

E1

PDH interfaces

Not in use

Ethernet interfaces

EIF2 in use => Autodetect

Ethernet switching

QoS aware Ethernet switching not in use

Queue weights

Queue 2 = 8, Queue 3 = 4, Queues 4-6 = 1

QoS classification:

Mode

Priority queue for Non-IP frames

DSCP to priority queue mapping

DSCP

DSCP 46, 48 => Queue 1

DSCP 34, 36, 38 => Queue 2

DSCP 26, 28, 30 => Queue 3

DSCP 10, 12, 14, 18, 20, 22 => Queue 4

VLAN aware configuration

Ethernet interfaces shaper

VLAN aware switching not in use

Speed and duplex (Egress & Ingress)

Egress burst size = 0.0%

Ethernet link OAM

Not in use

Ethernet service OAM

Not in use

CIR = 1.0 Mbit/s

Quality of Service

Defaults in use

IP interfaces:

Settings

OSPFv2

MTU = 1500 octets

Not in use

Transport Ethernet interface:

Interface address

None (VLANs in use)

Traffic shaping type

WFQ

Shaper information rate


Shaper burst size

100.0 Mbit/s
1522 octets

Committed information rate

5.0 Mbit/s

Enable QoS

Yes

Include Ethernet overhead

No

Proxy ARP

Not in use

OSPFv2 parameters

OSPF disabled

VLAN 901:

VLAN ID

901

Address

10.117.250.2 / 29

CES over PSN VLAN

Committed information rate

No

0.5 Mbit/s

Enable QoS

No

Proxy ARP

Not in use

OSPFv2 parameters

OSPF disabled

VLAN 902:

VLAN ID

902

Address

CES over PSN VLAN

Committed information rate

10.167.250.2 / 29

No

0.1 Mbit/s

Enable QoS

Yes

Proxy ARP

Not in use

OSPFv2 parameters

OSPF disabled

VLAN 903:

VLAN ID

903

Address

10.127.250.2 / 29

CES over PSN VLAN

Committed information rate

No

4.3 Mbit/s

Enable QoS

Yes

Proxy ARP

Not in use

OSPFv2 parameters

OSPF disabled

VLAN 904:

VLAN ID

904

Address

10.177.250.2 / 29

CES over PSN VLAN

Committed information rate

Enable QoS

No

0.1 Mbit/s

No

Proxy ARP

Not in use

OSPFv2 parameters

OSPF disabled

CES over PSN settings

Minimum UDP port = 53248

IUB IP settings:

Far-end SCTP subnet

10.207.18.0 / 26

Minimum SCTP port

49152

Minimum UDP port

49152

CAC Committed bit rate

5.0 Mbps

Signalling bit rate

DCN bit rate

500 Kbps

100 Kbps

Frame protocol multiplexing:

Local UDP port

65535

Remote UDP port

65535

Multiplexing delay

2 ms

Multiplexing amount

30 packets

Timing over Packet

Not in use

Application addresses:

User plane 1

10.167.250.2

User plane 2

10.127.250.2

Control plane

10.117.250.2

Management plane

10.209.0.1

RTT measurement

Reflector not in use

TWAMP sessions

Not in use

Synchronization:

Timing sources

None

Sync Ethernet regenerator

Not in use

BTS routing:

Default gateway

10.177.250.1

BFD sessions

None

Static routes:

Destination

Netmask

Gateway

Preference

10.207.19.72

255.255.255.248

10.167.250.1

10.207.19.80

255.255.255.248

10.127.250.1

10.207.18.0

255.255.255.192

10.117.250.1

Route reinstallation delay

0s

IP filtering

Restricted mode for LMP = On

BTS settings

Configuration name

2+2+2, 20W

External 2.048 MHz sync output


Forward sync in co-siting

Not in use
Not in use

Security for Ethernet ports


Enter BTS to test state

Not in use
No

Sync sources for BTS FM

External 2.048 MHz synchronization in use

IP Iub signaling settings

Max assoc. retransmissions = 5

Max path retransmissions = 5

Automatic license distribution:

Enable SW monitoring

No

Automatic licensing in use


R99 channel elements

Yes
None

Concurrent mode settings

RF Sharing not enabled

Local Cell IDs

Cell 1 FRGP2, Ant 1&2 @ 20W

(FRGP2 only)

Cell 2 FRGP2, Ant 3&4 @ 20W

Cell 3 FRGP2, Ant 5&6 @ 20W

Intelligent shutdown

Carrier frequency

(UARFCN)

Not in use

Cell 1 = 10613

Cell 2 = 10613

Cell 3 = 10613

Local cell groups in use

No

BB and HSPA license allocations

None

Mapping HSPA to BB HW

No

HSDPA settings:

HSDPA 16 QAM support

HSDPA PFRP scheduler

In use

In use

HSDPA resource allocation

None

HSDPA shared scheduler

Not in use

HSDPA capacity sets:

BTS processing set 1

Not in use

BTS processing set 2

3 in use

BTS processing set 3

1 in use

HSDPA throughput:

Scheduler 1

18 steps

Scheduler 2

3 steps

HSDPA Iub delay thresholds

Defaults in use

HSUPA settings:

HSUPA FDE in use

HSUPA resource allocation

HS cell FACH state

Happy bit ratio filtering

No

Defaults in use

Not in use

In use (both), UPH threshold = 10 dB

HSUPA capacity sets:

BTS processing set 1

3 in use

SPI Class settings

Resource reservation for non-NBR

Defaults in use

10%

Antenna line management:

3GPP/AISG communication

DC voltage

Not in use

Not in use

Antenna line features:

SW update for antenna devices

Flexi WBTS 3GPP antenna tilt

Not in use

Not in use

Antenna line supervision

Not in use

RX signal level monitoring

Not in use

AISG MHA settings

Not in use

Antenna line settings:

FR1.2.1-ANT1 & 3 & 5


Antenna settings

Feeder loss = -3.0 dB


PHS filter not in use

Multiradio combiner not in use

Multiplexer not in use

VSWR minor fault = 1.5


VSWR major fault = 1.7

Additional RX gain = 0.0 dB

Uplink delay = 0 ns

Forced feeded voltage = Not set

RTT measurements
MHA settings

FR1.2.1-ANT2 & 4 & 6


Antenna settings

User-defined RTT delay = 8.2 ns


MHA not in use

Feeder loss = -3.0 dB

PHS filter not in use

Multiplexer not in use

Additional RX gain = 0.0 dB

Uplink delay = 0 ns

RTT measurements

User-defined RTT delay = 8.2 ns

MHA settings

MHA not in use

Siemens AISG1.1 TMA/RET

Not in use

RET settings

Not in use

System module EAC settings

None

Radio module EAC settings

None

No related Telecom Tutorials found.

Potrebbero piacerti anche