Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
5
Package list
1 Reader
Instruction Package
1
1 4 7 8 5 9 2 6 3 c/ 0/ OK /M
Accessory Package
Connector Jack
12V COM
Port PIN 1
P1 2 8 7 6 5
P3 4 3 2 1
12V COM
Exit Door Button sensor OPEN DOOR
PIN
Function Connector
EN CH
COMPACT CD-ROM
P1
P2
P3
P4
2 1
Function Connector
Power Supply
1 2
Power Supply
Output Controller
NO NC
Access control
P1
12V COM
FOR
1 2
GND
EN CH
COMPACT
windows
CD-ROM
P3
COM NC NO
DC12V
+12V GND
12V COM
P3
+12V
GND
COM GND
OPEN DOOR
P2
3 4 2 1
DATA0
P1
P2
P3
DATA1
GND RS485A RS485B GND
TCP/IP
RS485 6
P3
P4
2 3 4
P4
1 2 8 7 6
P1
P2
P3
RJ45 USB
Relay State
Relay State
+
Diode
Installation Diagram
2 1
Installation Steps:
1 2 3
Drill holes in the wall follow the hole position on back panel Install and fix back panel, connect related cables Fix access control reader
Door Sensor
+Diode
Power on to unlock
Power on to unlock
NC Mark +12V GND
Wiring Instruction
Door Sensor
The interface marked with for specific models, Please according to the practical device to wiring.
P1
Function PIN
Power
1 2
Red Black
DC12V GND
Communicate with PC
P2
P2
P1
RJ45(TCP/IP)
Relay states Function PIN Cable Color Description
P1 1 2 6 5
RS485
P2 4 3 2 1
PIN
Function
Connector
Power Supply
Wiegand Output
1 2 3 4
Wiegand DATA0 Output Wiegand DATA1 Output GND RS485A RS485B GND
Wiegand Output
+12V GND
D1
D0
P3
RS485
RS485
5 6
TCP/IP
COM 12V
P3
Relay
6 7 8
COM NC NO
COM 12V
P3
Relay
6 7 8
P3
Function PIN
Cable Color
Description
1 2 3 4
GND
5 6
Relay
7 8
Mini-USB
Important notice: Please carefully follow this wiring diagram, If the reader gets damaged by incorrect wiring then your warranty will be void.
Switch Power
Access control
V1.5
Reader Appearance LED
There are three colours for device status: Red, Blue and Green. Swipe the card here.
Add Card+Fingerprint: (Operation Steps show as figure 1.3) After registered you can continue register another user or swipe enroll card save and exit.
Swipe Enroll Card, begin
Continue to register
Swipe User Card
Place finger Place finger again, please
Underneath:
Mini USB Port Reset Button
Notice:When swipe card, Red LED flashes twice with two long beeps means the User Card have been registered.
Blue LED flashes Blue LED flashes Green LED lights up fast and FingerPrint fast and FingerPrint Four short beeps sensor lights up sensor lights up Registration Successed
Figure 1.3
Fingerprint Sensor
Place the finger here.
Screw Hole
Delete User:
Delete fingerprint only: (Operation Steps show as figure 1.4) After delete you can continue delete another user or swipe Delete Card save and exit. Swipe Delete
Card, begin
Continue to delete
Place finger
Notice: When place finger, Red LED flashes with long beep means the fingerprint does not exist in the device.
Make sure you cover the entire sensor surface with as much of your finger as possible.
=Figure 1.4
Incorrect method :
Delete Card / Card+Fingerprint: (Operation Steps show as figure 1.5) After delete you can continue delete another user or swipe Delete Card save and exit.
Swipe Delete Card, begin
Continue to delete
DO NOT move your finger before the backlights of sensor turns off.
DO NOT place finger away from the center of the sensor window.
Operation Guide
DC 12V supply the power for device. Blue LED flashes fast and Fingerprint Sensor lights with beeps. There are 4 cards in the packing: Enroll Card Delete Card User Card * 2
Notice: When swipe card, Red LED flashes with long beep means the fingerprint does not exist in the device.
Function button
Function Button
Add Fingerprint Only: (Operation Steps show as figure 1.1) After registed you can continue register another user or swipe Enroll Card save and exit.
Swipe Enroll Card, begin
Continue to register
Place finger Place finger again, please
Press the button until heard beeps, that eliminate Enroll Card and Delete Card information in the device. After that MUST register management cards (Enroll Card and Delete Card) to run the machine.
Swipe Enroll Card, end
Function Button Notice: When place finger, Red LED flashes with two long beeps means the finger have been registered.
Blue LED flashes Blue LED flashes fast and FingerPrint sensor lights up
Figure 1.1
Notice: The operation will not delete any user data stored in the device.
Register Management Cards (Enroll Card and Delete Card)
Add Card Only: ( Operation Steps show as figure 1.2) After registed you can continue register another user or swipe Enroll Card save and exit.
Swipe Enroll Card, begin
Continue to register
Swipe User Card Swipe User Card again, please Swipe Enroll Card, end Swipe Enroll Card Swipe Delete Card
Notice:When swipe card, Red LED flashes twice with two long beeps means the User Card have been registered.
Blue LED flashes Blue LED flashes fast and FingerPrint sensor lights up
Figure 1.2
In orginal state Blue LED flashes Green LED lights up Four short beeps Registration Successed
Figure 1.6