Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
www.huawei.com
Foreword
UE behaviors in idle mode include:
PLMN selection System information reception Cell selection and reselection Tracking area registration Paging procedure
Page1
Objectives
Upon completion of this course, you will be able to:
Describe the UE behaviors in RRC idle mode Describe the feature and algorithms of each behavior
Page2
Contents
1. Idle Mode Overview 2. PLMN selection 3. Cell Selection & Reselection 4. System Information Reception 5. Tracking Area Registration 6. Paging Monitoring Procedure
Page3
Page4
Page5
Contents
1. Idle Mode Overview 2. PLMN selection 3. Cell selection & Cell Reselection 4. System information reception 5. Tracking area registration 6. Paging monitoring procedure
Page6
PLMN Selection
Page7
PLMN Selection
Page8
Contents
1. Idle Mode Overview 2. PLMN Selection 3. Cell Selection & Cell Reselection 4. System information reception 5. Tracking area registration 6. Paging monitoring procedure
Page9
Page10
Cell Search
Slot synchronization
Page11
Cell Search
Page12
Cell Selection
Criteria for cell selection Srxlev > 0 and Squal > 0 Srxlev = Qrxlevmeas - (Qrxlevmin + Qrxlevminoffset) Pcompensation Squal = Qqualmeas (Qqualmin + Qqualminoffset)
Page13
Page14
Page15
Page16
Page17
The priorities of inter frequency and inter-RAT are classified into two types: Absolute priority
Static configuration
Dedicated priority
Temporarily configured by RRC
Page18
Page19
10
Note: if priority indicator is set Not CFG, then eNodeB use the same priority setting as local cell
Page20
UMTS
Page21
11
Page22
Page23
12
Page24
Page25
13
Serving cell
Neighbor cell
Page26
Page27
14
Page28
Criteria for Rx quality based (only for LTE&UMTS): Squal = Qqualmeas Qqualmin>ThreshXHighQ
Criteria for Rx level based (For all system) : Srxlev = Qqualmeas (Qqualmin + Pcompensation) > ThreshXHigh
Page29
15
Criteria based on Rx quality (only for LTE & UMTS) Squal_S < ThrshServLowQ and Squal_N > ThreshXLow Criteria based on Rx level (for all system) Srxlev_S < ThrshServLowQ and Srxlev_N > ThreshXLow
Page30
Page31
16
Contents
1. PLMN Selection 2. Cell Selection & Reselection 3. System Information Reception 4. Tracking Area Registration 5. Paging Monitoring Procedure
Page32
Page33
17
MIB Transmission
MIB DL Bandwidth PBCH PHICH Configuration Info SFN
Frame 0 1 2 3 4 5 6 7 8 9
SIB1 Transmission
SIB1: PLMN Identity List P-Max Frequency Band Indicator
SIB1
Cell Barred Indication Scheduling Info List Intra Frequency Reselection SIB Window Length Qrxlevminoffset
SFN
Page35
18
Other SIBs
SIB2: Common radio parameters used by all the UEs in a cell SIB3 Common cell reselection parameters for all the cells and intra-frequency cell reselection parameters SIB4 Intra-frequency neighboring cell list, reselection parameters of each neighboring cell used for cell reselection, and intra-frequency cell reselection blacklist SIB5 Inter Frequency Carrier List Inter Frequency Neighbor Cell List Inter Frequency Black Cell List
SIB6 Neighbor List for UTRAN UTRAN Reselection Info SIB7 Neighbor List for GERAN GERAN Reselection Info SIB8 Neighbor List for cdma2000 cdma2000 Reselection Info SIB9: Name of the home eNodeB SIB10 Earthquake and Tsunami Warning System (ETWS) primary notification SIB11 ETWS secondary notification
Page36
Page37
19
Page38
Page39
20
SI Update Period
MOD BCCHCFG
MOD PCCHCFG
Page40
Contents
1. PLMN Selection 2. Cell Selection & Reselection 3. System Information Reception 4. Tracking Area Registration 5. Paging Monitoring Procedure
Page41
21
A UE informs the EPC of its Tracking Area in two ways: Attach/Detach TA update
Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved. Page42
TA Update
TA updates are performed in the following situations:
The UE detects a new TA The periodic TA update timer expires The UE performs reselection to an E-UTRAN cell from another RAT The RRC connection is released because of load balancing The information on UE capabilities stored in the EPC changes The Discontinuous Reception (DRX) parameters changes
Page43
22
Contents
1. PLMN Selection 2. Cell Selection & Reselection 3. System Information Reception 4. Tracking Area Registration 5. Paging Monitoring Procedure
Page44
Trigger of Paging
Triggered by MME
MME initiates a paging message according to the TAL information in the message, the eNodeB transmits the paging message over the PCCH to the UE in all the cells belonging to the TAs in the TAL
Triggered by eNodeB
When the SI message changes, the eNodeB transmits a paging message to notify all the UEs in the EMMREGISTERED state in the cell and transmits the updated SI message in the next SI message modification period
Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved. Page45
23
Paging Mechanism
The SFN of a PF is derived from the following formula: SFN mod T = (T div N) x (UE_ID mod N) The subframe number i_s of a PO is derived from the following formula: i_s =Floor (UE_ID/N) mod Ns
Page46
The SFN of a PF is derived from the following formula: SFN mod T = (T div N) x (UE_ID mod N) The subframe number i_s of a PO is derived from the following formula: N_s = (UE_ID/N) mod Ns
Page47
24
The SFN of a PF is derived from the following formula: SFN mod T = (T div N) x (UE_ID mod N) The subframe number i_s of a PO is derived from the following formula: N_s = (UE_ID/N) mod Ns
Page48
The SFN of a PF is derived from the following formula: SFN mod T = (T div N) x (UE_ID mod N) The subframe number i_s of a PO is derived from the following formula: N_s = (UE_ID/N) mod Ns
Page49
25
Paging Configuration
MOD PCCHCFG
Page50
Thank you
www.huawei.com
26