Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
(June, 2007)
Air Technology Systems, Inc.
Notice
This document contains information protected by copyright. All rights are reserved. The owner of the equipment for which this manual is written may photocopy the contents of this manual for internal use only. No part of this document may be photocopied, reproduced, or translated into another language for use by anyone other than the owner of the equipment for which this manual is written without the prior written consent of Stulz Air Technology Systems, Inc. (SATS). This document contains confidential and proprietary information of Stulz Air Technology Systems, Inc. Distributing or photocopying this document for external distribution is in direct violation of U.S. copyright laws and is strictly prohibited without the express written consent of SATS. Unpublished rights reserved under the copyright laws of the United States and of other countries. Other brands and tradenames are trademarks of their respective owners. Copyright 2007 by Stulz Air Technology Systems, Inc. Printed in the United States of America. All rights reserved.
Stulz Air Technology Systems, Inc. 1572 Tilco Drive Frederick, MD 21704 USA
06/07 (June, 2007)
Air Technology Systems, Inc.
Press the SET + MODE buttons and hold for 3 to 5 seconds to enter the modifying mode of the FACTORY Level parameters. Enter the code 177 and press the SET button to access the modifiable parameters. For the above quick references, press the HOLD button to accept all changes. Press the RESUME button not to accept any changes.
NIGHT-TIME. Press the SET button to enable modification of the above 3 modes. Use the and buttons to change the setpoint. Note the symbol being modified will be in the bottom-right hand corner of the display during modification. Press the HOLD button to accept all the changes. Press the RESUME button not to accept any changes.
(June, 2007)
Air Technology Systems, Inc.
Automatic reset:
Some alarms are automatically reset when the cause is no longer present, that is, they are deactivated: relevant message on the display, buzzer and alarm relay.
Manual reset:
Pressing the RESUME button for more than 3 seconds, if the alarm conditions have been removed, the instrument returns to the normal operation and the alarm relay is de-energized. If, on the other hand, the alarm conditions persist, the alarm situation in progress remains.
HI T: High temperature alarm When the temperature measured by probe B1 rises above the value specified by the parameter P3 for a period longer than parameter P5, the buzzer and the high temperature alarm message, HI T, are activated. The alarm relay is not energized. LO T: Low temperature alarm When the temperature measured by probe B1 falls below the value specified by parameter P4 for a period longer than parameter P5, the buzzer and the low temperature alarm signal, LO T, are activated. The alarm relay is not energized.
2
Air Technology Systems, Inc.
(June, 2007)
E1: B1 temperature regulation probe error Signals the malfunctioning of the temperature probe used for temperature regulation (B1). Also check the position of jumper J1. In the case of an alarm, the controller provides the alarm message E1, the buzzer and the alarm relay are activated and all outputs are de-energized, except for the supply fan. The fan stays on to allow air circulation in public areas. The alarm is reset automatically, that is when communication is established again. E2: B2 auxiliary probe error Signals the malfunctioning of the B2 active probe. Also check the position of jumper J2. In the case of an alarm, the control provides the alarm message E2, the buzzer and the alarm relay are activated and the humidification and dehumidification functions are suspended. The alarm is reset automatically, that is when the sensor starts working correctly. HI H: High humidity alarm When the humidity measured by probe B2 rises above the value specified by parameter P8 for a time greater than P5, the high humidity alarm signal HI H is activated. The alarm relay and the buzzer are not activated LO H: Low humidity alarm When the humidity measured by probe B2 falls below the value specified by parameter P7 for a time greater than P5, the low humidity alarm signal LO H is activated. The alarm relay and the buzzer are not activated.
(June, 2007)
Air Technology Systems, Inc.
Product Warranty
SATS offers a two year standard limited warranty as stated below.
Stulz Air Technology Systems, Inc.s warranty does not cover failures caused by improper installation, abuse, misuse, misapplication, improper or lack of maintenance, negligence, accident, normal deterioration including wear and tear, or the use of improper parts or improper repair as determined by SATS. This warranty does not include costs for transportation, costs for removal or reinstallation of equipment or labor for repairs or replacement made in the field. THIS OBLIGATION AND LIABILITY OF STULZ AIR TECHNOLOGY SYSTEMS, INC. UNDER THIS WARRANTY DOES NOT INCLUDE LOSSES, DIRECT OR INDIRECT, FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
4
Air Technology Systems, Inc.
(June, 2007)
Technical Support
The SATS Product Support Group (PSG) is dedicated to the prompt reply and solution to any problem encountered with a unit. Should a problem develop that cannot be resolved using this manual, you may contact PSG at (240) 529-1399 Monday through Friday from 8:00 a.m. to 5:00 p.m. EST. If a problem occurs after business hours, dial the page number (301) 414-4514 and follow the steps below: 1. Wait for the dial tone. 2. Dial your telephone number (including area code). 3. Press the pound (#) key. 4. Wait for a busy signal. 5. Hang up the telephone. One of our service technicians will return your call. When calling to obtain support, it is vital to have the following information readily available: Unit Model Number (X-XXXX-XX) Description of Problem
The customer is responsible for the shipping cost incurred for shipping the defective part(s) back to SATS. Return of defective part(s) must be within 30 days at which time an evaluation of the part(s) is conducted and if the part is found to have a manufacturing defect a credit will be issued.
(June, 2007)
Air Technology Systems, Inc.
(June, 2007)
Air Technology Systems, Inc.