Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Section
630
Page
630.
Issue
Operating Range:
Cast Iron Series 124A/AE, 4124A/AE, 4124B, 324A,
4324A, 224A/AE, 4224A/AE & 4224B
Ductile Iron Series 126A, 4126A, 226A & 4226A
Nominal
Flow
(GPM)
15 - 1600
(M3/hr.)
3.4 - 364
Pressure
Range
(PSI)
To 200 PSI
(Bar)
To 14 Bar
Temp.
Range
( oF )
60F to +650F
( C)
51C to +343C
(SSU)
Viscosity
Range
(cSt)
15 - 1600
(M /hr.)
3.4 - 364
Pressure
Range
(PSI)
To 200 PSI
(Bar)
To 14 Bar
Temp.
Range
( oF )
20F to +800F
( oC )
29C to +427C
(SSU)
Viscosity
Range
(GPM)
(cSt)
H
HL
K
KK
L/LQ
LL
LS
Q
QS
N
R
RS
Cast Iron,
Ductile Iron &
Steel Externals
Series
GPM
15
30
75
100
135
140
200
300
500
600
1100
1600
M3/hr
3.4
6.8
17.0
23
31
32
45
68
114
136
250
364
Stainless Steel
Series
GPM
10
20
45
65
90
110
160
200
320
600
1100
1600
M3/hr
2.3
4.5
10
15
20
25
36
45
73
136
250
364
(GPM)
10-1600
(M /hr.)
2.3 - 364
Pressure
Range
(PSI)
To 200 PSI
(Bar)
To 14 Bar
Temp.
Range
( oF )
120F to +500F
( oC )
84C to +260C
(SSU)
Viscosity
Range
(cSt)
2007
Section
630
Page
630.
Issue
Series Description
All Universal Seal pumps are equipped with pump casings that can be positioned to meet common piping configurations.
H through Q sizes have standard 90 ports which can be turned to any of eight positions (LQ, LL, and LS sizes will
not allow a port at the 6 oclock position). Optional opposite ports are available in some sizes and materials. QS, N,
and R sizes have opposite ports as standard, with optional 90 ports available in some materials. Direction of flow is
reversible so any given port can be used as suction or discharge. The relief valve must point to the suction port in
all cases. Typical port configurations are shown below. See Optional Casings tables for available port options.
90 port
options
Opposite
port options
2007
Section
630
Page
630.
Issue
Large diameter
threaded bearing
housing allows
easy removal of
cartridge seals.
Double row
ball or tapered
bearing for axial
thrust control.
One-piece
cast bracket
provides rigid
foundation to
maximize seal
and bearing life.
2007
Internal relief
valve standard.
Return-to-tank
and jacketed
relief valves
optional.
Section
630
Page
630.
Issue
Field
2
Field
3
L Q
Size:
H
HL
K
KK
L
LQ
LL
LS
Q
QS
N
R
RS
Field
4
Field
5
Shaft
Seal:
4 = Mechanical
Seal
blank = packing
Jacketing:
1 = no jacketing
2 = jacketed
3 = foot mount casing
w/ jacketed bracket
Field
6
Field
7
2 4
Materials of
Contstruction:
3 = Steel
Externals
4 = Cast Iron
6 = Ductile
Iron
7 = Stainless
Steel
Seal
Location:
A = Stuffing
Box with
Universal
Seal
Design
B = BehindtheRotor (Cast
Iron only)
Field
8
E
Primary Shaft Diameter
(L, LQ and LL sizes
in Cast Iron only):
blank = 1-7/16"
E = 1-5/8"
See dimension drawings
for shaft diameter at
coupling
Note on Field 4 that only the N through RS sizes are the foot mount with jacketed bracket (3). All other sizes are available with
either no jacketing (1) or jacketed (2). The N size is standard with a jacketed bracket and non-jacketed head and non-jacketed relief
valve, while the R and RS sizes are standard with a jacketed bracket, a jacketed head, and a non-jacketed relief valve. There are
relief valve options available on those pump models designed to accept a relief valve. Options include a jacketed relief valve for the
N pump (only available with the non-jacketed head). A non-jacketed relief valve is available for the R pump.
The Universal Seal series comes in several different versions depending on the type and location of the sealing device. The L, LQ
and LL size also offer two shaft diameter options. The model numbering scheme is illustrated in the table below, with the cast iron,
non-jacketed series pumps.
Stuffing Box
Seal
Behind the
Rotor Seal
H124A
H4124A
H4124B
HL124A
HL4124A
HL4124B
K124A
K1424A
K4124B
KK124A
KK4124A
KK4124B
L124A
L124AE
LQ124A
LQ124AE
LL124A
LL124AE
L4124 A
L4124AE
LQ4124A
LQ4124AE
LL4124A
LL4124AE
LS124A
LS4124A
NA
Q124A
Q4124A
NA
QS124A
QS4124A
NA
N324A
N4324A
NA
R324A
R4324A
NA
RS324A
RS4324A
NA
L4124B
LQ4124B
LL4124B
Model Sizes
L, LQ, LL
Shaft Seal
Dimension
U
Dimension
124A, 4124A
224A, 4224A
1-7/16
1-1/8
124AE, 4124AE
224AE, 4224AE
4124B
1-5/8
1-7/16
2007
Section
630
Page
630.
Issue
Standard-Jacketed Pumps
Jacketed Head
Fully-Jacketed Pumps
Pumps with a Fully-Jacketed Option use the StandardJacketed pumps series designation, but replace the standard
casing with a jacketed casing, in addition to the jacketed
head and bracket. Available for steel and stainless steel
models, the jacketed casing provides heat transfer surface
area around the perimeter of the rotor, in the inlet and
discharge throat areas, and in many sizes into the flanges.
Fully jacketed pumps are typically used in applications where
precisely maintaining a uniform, predetermined temperature
is critical, in extreme environments, and to provide faster
startup of cold processes to improve production efficiency.
Jacketed
Bracket
Jacketed
Casing
Jacketed Head
N4324A
Non-Jacketed Head with
Coverplates Shown
R4323A
Jacketed Head with
Non-Jacketed Relief
Valve Shown
Jacketed
Flange
2007
Section
630
Page
630.
Issue
Non-Jacketed Series
124A/AE, 4124A/AE, 4124B,
Jacketed Series
224A, 4224A, 224AE,
4224AE, 4224B
324A , 4324A
Casing
Stainless Steel
Non-Jacketed Series
126A , 4126A
Jacketed Series
226A & 4226A
Steel Externals
Non-Jacketed Series
123A, 4123A, 323A, 4323A
Jacketed Series
223A, 4223A
Non-Jacketed Series
127A, 4127A, 327A,
4327A
Jacketed Series
227A, 4227A
Cast Iron
ASTM A48, Class 35B
Ductile Iron
ASTM A536 Grade 60-40-18
Steel
ASTM A216, Grade WCB
Head
Cast Iron
ASTM A48, Class 35B
Ductile Iron
ASTM A536 Grade 60-40-18
Steel
ASTM A216, Grade WCB
Stainless Steel
ASTM A 743, Grade CF8M
Stainless Steel
ASTM A 743, Grade CF8M
Case Hardened
Cast Iron
ASTM A48, Class 35B
Steel
ASTM A216, Grade WCB
Steel
ASTM A216, Grade WCB
Cast Iron
ASTM A48, Class 35B
Bracket
Cast Iron
ASTM A48, Class 35B
Ductile Iron
ASTM A536 Grade 60-40-18
Steel
ASTM A216, Grade WCB
Idler
Cast Iron
ASTM A48 Class 35B
Cast Iron
ASTM A48 Class 35B
Cast Iron
ASTM A48 Class 35B
Stainless Steel
ASTM A 743, Grade CF8M
Stainless Steel
ASTM A 743, Grade CF8M
Case Hardened
Cast Iron
ASTM A48, Class 35B
Cast Iron
ASTM A48, Class 35B
Cast Iron
ASTM A48, Class 35B
Steel
ASTM A148, Grade 80-40
Steel
ASTM A148, Grade 80-40
Steel
ASTM A148, Grade 80-40
Rotor Shaft
Steel
ASTM A108, Grade 1045
Steel
ASTM A108, Grade 1045
Steel
ASTM A108, Grade 1045
Idler Pin
Hardened Steel
ASTM A108, Grade 1045
Hardened Steel
ASTM A108, Grade 1045
Hardened Steel
ASTM A108, Grade 1045
Bronze
ASTM B584 (B505), Alloy C93700
Bronze
ASTM B584 (B505), Alloy C93700
Bronze
ASTM B584 (B505), Alloy C93700
Carbon Graphite
Carbon Graphite
Carbon Graphite
Bronze
ASTM B584 (B505), Alloy C93700
Bronze
ASTM B584 (B505), Alloy C93700
Bronze
ASTM B584 (B505), Alloy C93700
Carbon Graphite
Carbon Graphite
Carbon Graphite
Cast Iron
ASTM A48, Class 35B
Steel
ASTM A216, Grade WCB
Steel
ASTM A216, Grade WCB
Component
Rotor
Idler
Bushing
Bracket
Bushing
Standard
Steel
Fitted
Packed
Mech.
Seal
Packed
Mech.
Seal
Internal Pressure
Relief Valve
Ductile Iron
Stainless Steel
ASTM A 743, Grade CF8M
Case Hardened
Stainless Steel
ASTM A276 Type XM-19
or 316 condition B
Hard Coated Stainless Steel
ASTM A276 Type 316
Colmonoy # 6 Coated
Carbon Graphite
Carbon Graphite
Stainless Steel
ASTM A 743, Grade CF8M
KK, LS, QS, N and RS sizes have ductile iron rotor, ASTM A536 Grade 60-40-18.
Steel fitted Q and QS sizes have steel idler.
H and HL sizes have powdered metal idler, MPIF Std 35 FC-0208-50.
H-LL 4124B (Behind-the-Rotor) pumps have bronze bracket bushing with Buna N seal, carbon graphite for Viton or PTFE seals.
Material specifiction for HL steel rotor is AISI 8620, LS steel rotor is ASTM A148 80-50.
RS relief valve not available. Contact factory for jacketing options.
Bearing
Housing
Bracket
Rotor
Bracket Shaft
Bushing
Casing
Rotor
Idler
Idler
Bushing Head
Internal
Pressure
Relief
Valve
2007
Section
630
Page
630.
Issue
Pump Size
H
HL
KK
LQ
LL
LS
QS
RS
SSU
25,000
7,500
25,000
25,000
25,000
25,000
2,500
75,000
7,500
75,000
75,000
25,000
75,000
cSt
5,500
1,650
5,500
5,500
5,500
5,500
550
16,500
1,650
16,500
16,500
5,500
16,500
For low viscosities or non-lubricating liquids Below 100 SSU (20 cSt)
Carbon graphite bushings.
Cast iron idler for iron or steel pumps, or Ryton or 770 stainless alloy idler for stainless steel pumps.
Pump should be operated at slower than normal speeds, which may require a larger pump.
For high temperatures Above 225 F (107C)
High temperature elastomers Buna up to 225F (107C); Viton up to 350F (177C); PTFE up to 450F (232C); or
Kalrez up to 550F (288C); Grafoil up to 700F. (371C).
High temperature relief valve above 350oF (177oC).
High temperature bushings recommended depending on temperature, size and specific material. See ESB-3 for
recommendations.
Addiitional operating clearances may be required depending on temperature, size and specific material. See ES-2 for
recommendations.
For temperatures above 450oF (232oC), special materials and sealing requirements may be needed. Contact factory for
recommendations.
Pump should be operated at slower than normal speeds, which may require a larger pump.
For abrasive or dirty liquids
If possible, filter or strain out the abrasives present.
Wear resistant bushings - hardened cast iron, tungsten carbide, colmonoy or silicon carbide.
Abrasive-resistant idler pin - tungsten carbide, colmonoy coated or chrome oxide coated pins.
Hardened or hard-coated shafting.
Abrasive-resistant seal.
Behind-the-rotor, abrasive resistant seal.
For high concentrations of abrasives or particle sizes greater than 250 microns (0.010 in), contact factory for
recommendations.
Pump should be operated at slower than normal speeds, which may require a larger pump.
Consult factory for specific recommendations.
Viton and Kalrez are registered trademarks of DuPont Dow Elastomers, LLC.
2007
Section
630
Page
630.
Issue
LQ (LQ4124A shown)
(Q124A shown)
K & KK
(K123 shown)
LS
LL (LL4126A shown)
QS
(QS4124A shown)
(R324A shown)
RS
(L124A shown)
(LS124A shown)
(N4324A shown)
(RS324A shown)
2007
Section
630
Page
630.
Issue
Standard
Port Size
Packed
Stuffing Box
Seal
Behind the
Rotor Seal
H124A
H126A
H123A
H127A
HL124A
HL126A
HL123A
HL127A
K124A
K126A
K123A
K127A
KK124A
KK126A
KK123A
KK127A
L124A/AE
L126A
LQ124A/AE
LQ126A
LQ123A
LQ127A
LL124A/AE
LL126A
LL123A
LL127A
H4124A
H4126A
H4123A
H4127A
HL4124A
HL4126A
HL4123A
HL4127A
K4124A
K4126A
K4123A
K4127A
KK4124A
KK4126A
KK4123A
KK4127A
L4124A/AE
L4126A
LQ4124A/AE
LQ4126A
LQ4123A
LQ4127A
LL4124A/AE
LL4126A
LL4123A
LL4127A
H4124B
N/A
N/A
N/A
HL4124B
N/A
N/A
N/A
K4124B
N/A
N/A
N/A
KK4124B
N/A
N/A
N/A
L4124B
N/A
LQ4124B
N/A
N/A
N/A
LL4124B
N/A
N/A
N/A
Inches
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
LS124A
LS126A
LS123A
LS127A
Q124A
Q126A
Q123A
Q127A
QS124A
QS126A
QS123A
QS127A
N324A
N323A
N327A
LS4124A
LS4126A
LS4123A
LS4127A
Q4124A
Q4126A
Q4123A
Q4127A
QS4124A
QS4126A
QS4123A
QS4127A
N4324A
N4323A
N4327A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
R324A
R323A
R327A
RS324A
RS323A
RS327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
Nominal Pump
Rating (750 SSU
and below)
GPM
15
15
15
10
30
30
30
20
80
80
80
50
100
100
100
65
135
135
135
135
135
90
140
140
140
110
RPM
1750
1750
1750
1150
1750
1750
1750
1150
780
780
780
520
780
780
780
520
640
640
640
640
640
420
520
520
520
420
3
3
3
3
4
4
4
4
6
6
6
6
6
6
6
200
200
200
160
300
300
300
200
500
500
500
320
600
600
600
640
640
640
520
520
520
520
350
520
520
520
350
350
350
350
8
8
8
10
10
10
1100
1100
1100
1600
1600
1600
280
280
280
280
280
280
Max.
Hydrostatic
Pressure
Max.
Discharge
Pressure
PSIG
PSIG
400
200
150
400
200
150
400
200
150
400
200
150
400
400
200
200
150
400
200
150
400
400
400
400
400
400
Max.
Recommended
Approx.
Steel Fitted
Temp. for Standard
Shipping
Recommended
o
Pump ( F)
Weight with
Above
Valve
Mech
Packed
Seal
SSU
Pounds
38
38
450
225
25,000
43
375
375
N/A
48
40
40
450
225
7,500
45
375
375
N/A
50
105
105
450
225
25,000
120
350
350
N/A
125
110
110
450
225
25,000
125
350
350
N/A
130
155
450
225
25,000
155
175
450
225
25,000
175
185
350
350
N/A
205
185
185
450
225
2,500
195
350
350
N/A
240
200
450
225
75,000
125
325
325
N/A
200
450
225
7,500
125
250
250
N/A
200
450
225
75,000
125
250
250
N/A
200
450
225
75,000
200
175
175
N/A
200
450
225
25,500
175
175
175
N/A
125
450
225
75,000
125
175
175
N/A
For maximum recommended discharge pressures at different viscosities, see performance curves. If suction pressure exceeds 50 PSIG, consult factory.
Extra clearances are required above 225 F. Higher temperatures can be handled with special construction, consult factory.
Ports are tapped for standard (NPT) pipe.
Ports are suitable for use with 125# ANSI cast iron companion flanges or flanged fittings.
Ports are suitable for 150# ANSI steel or stainless steel companion flanges or flanged fittings.
See p.630.11 for other port size options.
2007
190
190
200
220
440
440
450
460
540
540
550
560
810
810
810
1435
1435
1435
1580
1580
1580
Section
630
Page
630.10
Issue
Port Size
Nominal Pump
Rating (165 cSt and
below)
Packed
Stuffing Box
Seal
Behind the
Rotor Seal
mm
M3/hr
RPM
H124A
H126A
H123A
H127A
HL124A
HL126A
HL123A
HL127A
K124A
K126A
K123A
K127A
KK124A
KK126A
KK123A
KK127A
L124A/AE
L126A
LQ124A/AE
LQ126A
LQ123A
LQ127A
LL124A/AE
LL126A
LL123A
LL127A
LS124A
LS126A
LS123A
LS127A
Q124A
Q126A
Q123A
Q127A
QS124A
QS126A
QS123A
QS127A
N324A
N323A
N327A
H4124A
H4126A
H4123A
H4127A
HL4124A
HL4126A
HL4123A
HL4127A
K4124A
K4126A
K4123A
K4127A
KK 4124A
KK4126A
KK4123A
KK4127A
L4124A/AE
L4126A
LQ4124A/AE
LQ4126A
LQ4123A
LQ4127A
LL4124A/AE
LL4126A
LL4123A
LL4127A
LS4124A
LS4126A
LS4123A
LS4127A
Q4124A
Q4126A
Q4123A
Q4127A
QS4124A
QS4126A
QS4123A
QS4127A
N4324A
N4323A
N4327A
H4124B
N/A
N/A
N/A
HL4124B
N/A
N/A
N/A
K4124B
N/A
N/A
N/A
KK4124B
N/A
N/A
N/A
L4124B
N/A
LQ4124B
N/A
N/A
N/A
LL4124B
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
38
38
38
38
38
38
38
38
50
50
50
50
50
50
50
50
50
50
65
65
65
65
75
75
75
75
75
75
75
75
100
100
100
100
150
150
150
150
150
150
150
2.8
2.8
2.8
1.9
5.6
5.6
5.6
3.7
18
18
18
11
23
23
23
15
31
31
31
31
31
20
32
32
32
25
45
45
45
36
68
68
68
45
114
114
114
73
136
136
136
1450
1450
1450
950
1450
1450
1450
950
780
780
780
520
780
780
780
520
640
640
640
640
640
420
520
520
520
420
640
640
640
520
520
520
520
350
520
520
520
350
350
350
350
R324A
R323A
R327A
RS324A
RS323A
RS327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
N/A
N/A
N/A
N/A
N/A
N/A
200
200
200
254
254
254
250
250
250
364
364
364
280
280
280
280
280
280
Max.
Hydrostatic
Pressure
Max.
Discharge
Pressure
BAR
BAR
28
28
28
28
28
28
28
28
28
28
28
28
28
Max.
Steel Fitted
Recommended
Const.
Temp. for Standard
Recommended
Pump (oC)
Above
Mech
Packed
Seal
cSt
14
232
107
5,500
10
191
191
N/A
14
232
107
1,650
10
191
191
N/A
14
232
107
5,500
10
177
177
N/A
14
232
107
5,500
10
177
177
N/A
14
232
107
5,500
14
232
107
5,500
10
177
177
N/A
14
232
107
550
10
177
177
N/A
14
232
107
16,500
163
163
N/A
14
232
107
1,650
121
121
N/A
14
232
107
16,500
121
121
N/A
14
232
107
16,500
14
79
79
N/A
14
232
107
5,500
12
79
79
N/A
232
107
16,500
79
79
N/A
Approx.
Shipping
Weight with
Valve
For maximum recommended discharge pressures at different viscosities, see performance curves. If suction pressure exceeds 50 PSIG, consult factory.
Extra clearances are required for temperatures above 107 C. Higher temperatures can be handled with special construction. Consult factory.
Ports are tapped for standard (NPT) pipe.
Ports are suitable for use with 125# ANSI cast iron companion flanges or flanged fittings.
Ports are suitable for 150# ANSI steel or stainless steel companion flanges or flanged fittings.
Port sizes are inch standard, not metric design or size. See p.630.11 for other port size options.
2007
KG
17
17
20
22
18
18
20
23
48
48
54
57
50
50
57
59
70
70
80
80
84
93
84
84
89
109
86
86
91
100
200
200
204
209
245
245
250
254
367
367
367
651
651
651
718
718
718
Section
630
Page
630.11
Issue
Stuffing Box
Seal
Behind the
Rotor Seal
Standard
Ports
Optional Casings
H124A
H126A
H123A
H127A
HL124A
HL126A
HL123A
HL127A
K124A
K126A
K123A
K127A
KK124A
KK126A
KK123A
KK127A
L124A/AE
L126A
H4124A
H4126A
H4123A
H4127A
HL4124A
HL4126A
HL4123A
HL4127A
K4124A
K4126A
K4123A
K4127A
KK 4124A
KK4126A
KK4123A
KK4127A
L4124A/AE
L4126A
H4124B
N/A
N/A
N/A
HL4124B
N/A
N/A
N/A
K4124B
N/A
N/A
N/A
KK4124B
N/A
N/A
N/A
L4124B
N/A
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
1.5
2
2
2
1.5
2
2
2
2
3
2.5
2.5
2
3
2.5
2.5
LQ124A/AE
LQ4124A/AE
LQ4124B
2.5
2.5
LQ126A
LQ123A
LQ127A
LL124A/AE
LL126A
LL123A
LL127A
LS124A
LS126A
LS123A
LS127A
LQ4126A
LQ4123A
LQ4127A
LL4124A/AE
LL4126A
LL4123A
LL4127A
LS4124A
LS4126A
LS4123A
LS4127A
N/A
N/A
N/A
LL4124B
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
2.5
2.5
3
4
3
4
4
3
3
3
4
4
4 *
4
4
3
3
4
4
Q124A
Q4124A
N/A
Q126A
Q123A
Q127A
QS124A
QS126A
QS123A
QS127A
N324A
N323A
N327A
R324A
R323A
R327A
RS324A
RS3233A
RS327
Q4126A
Q4123A
Q4127A
QS4124A
QS4126A
QS4123A
QS4127A
N4324A
N4323A
N4327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
4
4
4
6
6
6
6
6
6
6
8
8
8
10
10
10
2
2
2
2
2
2.5
4
2.5
2.5
2.5
4
2.5
2.5
2.5
3
3
2.5
3
3
3
4
4
4
4
4
3
3
3
3
4
4
4
4
6*
Side 5,
Top 6
4
4
5*
4
4
6
Side 4 ,
Top 8
Side 4 , Side 6,
Top 8
Top 8
5
3
5
4
6*
5
6*
6*
6
6
6
6
5
6
6
6
6
Port(s) suitable for 150# ANSI steel or stainless steel companion flanges or
flanged fittings.
Port(s) suitable for 300# ANSI steel or stainless steel companion flanges or
flanged fittings.
90 port arranged for Right Hand inlet (viewed from shaft end)
90 port arranged for Left Hand inlet (viewed from shaft end)
Non-Rotatable Ports at 90 degree angle, contact factory for available
orientation (right hand or left hand)
Opposite Ports
* Core smaller than port size
2007
Section
630
Page
630.12
Issue
Stuffing Box
Seal
Behind the
Rotor Seal
H124A
HL124A
H126A
HL126A
H123A
HL123A
H127A
HL127A
K124A
KK124A
K126A
KK126A
K123A
KK123A
K127A
KK127A
H4124A
HL4124A
H4126A
HL4126A
H4123A
HL4123A
H4127A
HL4127A
K4124A
KK4124A
K4126A
KK4126A
K4123A
KK4123A
K4127A
KK4127A
H4124B
HL4124B
L124A/AE
L4124A/AE
L4124B
L126A
L4126A
LQ124A/AE
LQ4124A/AE
LQ126A
LQ4126A
LQ123A
LQ4123A
LQ127A
LQ4127A
LL124A/AE
LL4124A/AE
LL126A
LL4126A
LL123A
LL4123A
LL127A
LL4127A
LS124A
LS126A
LS123A
LS127A
Q124A
Q126A
Q123A
Q127A
LS4124A
LS4126A
LS4123A
LS4127A
Q4124A
Q4126A
Q4123A
Q4127A
in
3.00
4.75
3.50
2.75
2.25
6.75
3.50
0.47
0.99
3.38
5.19
mm
76.2
120.6
88.9
57.1
171.4
88.9
11.9
25.1
85.8
131.8
in
4.00
4.75
3.50
2.75
2.25
6.75
3.50
0.47
0.99
3.38
5.19
mm
101.6
120.6
88.9
69.8
57.1
171.4
88.9
11.9
25.1
85.8
131.8
in
5.12
8.00
5.50
4.00
2.75
9.25
4.00
0.53
1.42
3.00
9.38
mm
130.0
203.2
139.7
101.6
69.8
234.9
101.6
13.5
36.1
76.2
238.3
in
5.25
8.00
5.50
4.00
2.75
9.25
4.00
0.53
1.42
3.00
9.38
mm
133.3
203.2
139.7
101.6
69.8
234.9
101.6
13.5
36.1
76.2
238.3
in
6.50
10.25
7.00
4.38
4.00
10.00
5.38
0.53
3.38
9.12
mm
165.1
260.3
177.8
111.3
101.6
254.0
136.7
13.5
50.8
85.9
231.6
2.5
in
7.19
10.25
7.00
4.38
4.00
10.00
5.38
0.53
3.38
9.12
mm
182.6
260.3
177.8
111.3
101.6
254.0
136.7
13.5
50.8
85.9
231.6
2.5
in
7.19
10.25
7.00
4.38
4.00
10.00
5.38
0.53
3.38
9.12
mm
182.6
260.3
177.8
111.3
101.6
254.0
136.7
13.5
50.8
85.9
231.6
in
7.19
10.25
7.00
4.38
4.00
10.00
5.38
0.53
3.38
9.12
mm
182.6
260.3
177.8
111.3
101.6
254.0
136.7
13.5
50.8
85.9
231.6
in
7.19
10.25
7.00
4.38
4.00
10.00
5.38
0.53
3.38
9.12
mm
182.6
260.3
177.8
111.3
101.6
254.0
136.7
13.5
50.8
85.9
231.6
in
7.19
10.25
7.00
4.38
4.00
10.00
5.38
0.53
2.55
4.75
9.12
mm
182.6
260.3
177.8
111.3
101.6
254.0
136.7
13.5
64.8
120.6
231.6
in
8.25
14.00
8.75
4.12
4.00
10.00
6.00
0.69
3.58
6.62
11.12
mm
209.5
355.6
222.2
104.6
101.6
254.0
152.4
17.5
90.9
168.1
282.4
A
(in)
1.5
1.5
K4124B
KK4124B
LQ4124B
LL4124B
69.8
2007
Section
630
Page
630.13
Issue
Model Number
Packed
Stuffing Box
Seal
H124A
HL124A
H126A
HL126A
H4124A
HL4124A
H4126A
HL4126A
H123A
HL123A
H127A
HL127A
H4123A
HL4123A
H4127A
HL4127A
K124A
KK124A
K126A
KK126A
K4124A
KK4124A
K4126A
KK4126A
K123A
KK123A
K127A
KK127A
K4123A
KK4123A
K4127A
KK4127A
L124A/AE
L4124A/AE
L126A
L4126A
LQ124A/AE
LQ4124A/AE
LQ126A
LQ4126A
LQ123A
LQ4123A
LQ127A
LQ4127A
LL124A/AE
LL4124A/AE
LL126A
LL4126A
LL123A
LL4123A
LL127A
LL4127A
LS124A
LS126A
LS123A
LS127A
LS4124A
LS4126A
LS4123A
LS4127A
Q124A
Q126A
Q123A
Q127A
Q4124A
Q4126A
Q4123A
Q4127A
in
1.19
0.56
0.62
10.44
13.25
1.62
0.75
.19 x .09
2.85
mm
30.2
14.2
15.7
265.2
336.5
41.1
19.0
4.83 x2.29
72.4
in
1.19
0.56
0.62
10.44
13.25
1.62
0.75
.19 x .09
2.85
mm
30.2
14
15.7
265.2
336.5
41.1
19.0
4.83 x2.29
72.4
in
1.75
0.62
0.62
14.12
18.12
2.25
1.12
.25 x .12
5.25
mm
44.4
15.7
15.7
358.6
460.2
57.1
28.4
6.35 x 3.05
133.3
in
1.75
0.62
0.62
14.12
18.12
2.25
1.12
.25 x .12
5.25
mm
44.4
15.7
15.7
358.6
460.2
57.1
28.4
6.35 x 3.05
133.3
in
mm
in
mm
in
mm
in
mm
in
mm
1.75
0.62
0.62
15.62
19.62
2.25
1.12
.25 x .12
5.43
44.4
15.7
15.7
396.7
498.3
57.1
28.7
6.35 x 3.05
137.9
1.75
0.62
0.62
15.62
19.62
2.25
1.12
.25 x .12
5.43
44.4
15.7
15.7
396.7
498.3
57.1
28.7
6.35 x 3.05
137.9
1.75
0.62
0.62
15.62
19.62
2.25
1.12
.25 x .12
5.43
44.4
15.7
15.7
396.7
498.3
57.1
28.7
6.35 x 3.05
137.9
2.25
0.62
0.62
15.62
20.12
2.25
1.12
.25 x .12
5.43
57.1
15.7
15.7
396.7
511.0
57.1
28.7
6.35 x 3.05
137.9
2.25
0.62
0.62
15.62
20.12
2.25
1.12
.25 x .12
5.43
57.1
15.7
15.7
396.7
511.0
57.1
28.7
6.35 x 3.05
137.9
in
2.44
0.62
0.62
15.75
21.69
3.50
1.44
.38 x .19
5.43
mm
62.0
15.7
15.7
400.0
550.9
88.9
36.6
9.65 x 4.83
137.9
in
3.00
0.75
1.00
19.25
26.75
4.50
1.94
.50 x .25
8.25
mm
76.2
19.0
25.4
488.9
679.4
114.3
49.3
12.70 x 6.35
209.5
Behind the
Rotor Seal
H4124B
HL4124B
K4124B
KK4124B
L4124B
LQ4124B
LL4124B
T dimension shown for Cast Iron sizes L, LQ and LL is for A models. dimension for L, LQ and LL size 124AE, 4124AE and 4124B pumps is 2.35 (59.7 mm).
U dimension shown for Cast Iron sizes L, LQ and LL is for A models. U dimension for L, LQ and LL size 124AE, 4124AE and 4124B pumps is 1.44 (36.6 mm).
V dimension shown for Cast Iron sizes L, LQ and LL is for A models. V dimension for L, LQ and LL size 124AE, 4124AE and 4124B pumps is 0.38 X 0.19
(9.65 X 4.83 mm).
2007
Section
630
Page
630.14
Issue
Dimensions in
inches (mm)
2007
Section
630
Page
630.15
Issue
Max.
Discharge
Pressure for
100 SSU
Liquid at
rated speed
PSIG
PSIG
Model Number
Packed
Stuffing Box
Seal
H224A
H226A
H223A
H227A
HL224A
HL226A
HL223A
HL227A
K224A
K226A
K223A
K227A
KK224A
KK226A
KK223A
KK227A
L224A/AE
L226A
LQ224A/AE
LQ226A
LQ223A
LQ227A
LL224A/AE
LL226A
LL223A
LL227A
LS224A
LS226A
LS223A
LS227A
Q224A
Q226A
Q223A
Q227A
QS224A
QS226A
QS223A
QS227A
N324A
N323A
N327A
H4224A
H4226A
H4223A
H4227A
HL4224A
HL4226A
HL4223A
HL4227A
K4224A
K4226A
K4223A
K4227A
KK 4224A
KK4226A
KK4223A
KK4227A
L4224A/AE
L4226A
LQ4224A/AE
LQ4226A
LQ4223A
LQ4227A
LL4224A/AE
LL4226A
LL4223A
LL4227A
LS4224A
LS4226A
LS4223A
LS4227A
Q4224A
Q4226A
Q4223A
Q4227A
QS4224A
QS4226A
QS4223A
QS4227A
N4324A
N4323A
N4327A
R324A
R323A
R327A
RS324A
RS323A
RS327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
Behind the
Rotor Seal
H4224B
N/A
N/A
N/A
HL4224B
N/A
N/A
N/A
K4224B
N/A
N/A
N/A
KK4224B
N/A
N/A
N/A
L4224B
N/A
LQ4224B
N/A
N/A
N/A
LL4224B
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Port Size
Nominal Pump
Rating (750 SSU
and below)
Inches
GPM
RPM
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
6
6
6
6
6
6
6
15
15
15
10
30
30
30
20
80
80
80
50
100
100
100
65
135
135
135
135
135
90
140
140
140
110
200
200
200
160
300
300
300
200
500
500
500
320
600
600
600
1750
1750
1750
1150
1750
1750
1750
1150
780
780
780
520
780
780
780
520
640
640
640
640
640
420
520
520
520
420
640
640
640
520
520
520
520
350
520
520
520
350
350
350
350
8
8
8
10
10
10
1100
1100
1100
1600
1600
1600
280
280
280
280
280
280
400
Packed
Mech
200
450
450
25,000
150
375
375
N/A
450
450
7,500
150
375
375
N/A
200
450
450
25,000
150
350
350
N/A
200
450
450
25,000
150
350
350
N/A
200
450
450
25,000
200
450
450
25,000
150
350
350
N/A
200
450
450
2,500
150
350
350
N/A
200
450
450
75,000
125
325
325
N/A
200
400
400
7,500
125
250
250
N/A
200
400
400
75,000
125
250
250
N/A
200
300
300
75,000
200
175
175
N/A
200
300
300
25,500
175
175
175
N/A
125
300
300
75,500
125
175
175
N/A
200
400
400
400
400
400
400
400
400
400
400
400
400
Max.
Recommended
Steel Fitted
Temp. for Standard
Recommended
Pump (oF)
Above
Seal
SSU
Approx.
Shipping
Weight
with Valve
Pounds
42
42
42
47
45
45
45
52
120
120
120
125
125
125
125
130
175
175
190
190
190
210
200
200
210
255
210
210
210
230
480
480
490
500
580
580
590
600
810
810
810
1435
1435
1435
1580
1580
1580
NOTE: The N size is standard with a jacketed bracket and non-jacketed head and non-jacketed relief valve, while the R size is standard with a jacketed bracket, a
jacketed head, and a non-jacketed relief valve. RS size contact factory for jacketing options.
Ports are suitable for 150# ANSI steel or stainless steel companion flanges
For maximum recommended discharge pressures at different viscosities, see
or flanged fittings.
performance curves. If suction pressure exceeds 50 PSIG, consult factory.
See p. 630.16 for other port size options.
Higher temperatures can be handled with special construction, consult factory.
Temperature based on PTFE seal as standard. Lower temperature limits
Ports are tapped for standard (NPT) pipe.
may be required when using other seal elastomers.
Ports are suitable for use with 125# ANSI cast iron flanges or flanged fittings.
2007
Section
630
Page
630.16
Issue
Packed
Stuffing Box
Seal
Behind the
Rotor Seal
Port Size
mm
Nominal Pump
Rating
(165 cSt and
below)
M3/hr
RPM
H224A
H226A
H223A
H227A
HL224A
HL226A
HL223A
HL227A
K224A
K226A
K223A
K227A
KK224A
KK226A
KK223A
KK227A
L224A/AE
L226A
LQ224A/AE
LQ226A
LQ223A
LQ227A
LL224A/AE
LL226A
LL223A
LL227A
LS224A
LS226A
LS223A
LS227A
Q224A
Q226A
Q223A
Q227A
QS224A
QS226A
QS223A
QS227A
N324A
N323A
N327A
H4224A
H4226A
H4223A
H4227A
HL4224A
HL4226A
HL4223A
HL4227A
K4224A
K4226A
K4223A
K4227A
KK 4224A
KK4226A
KK4223A
KK4227A
L4224A/AE
L4226A
LQ4224A/AE
LQ4226A
LQ4223A
LQ4227A
LL4224A/AE
LL4226A
LL4223A
LL4227A
LS4224A
LS4226A
LS4223A
LS4227A
Q4224A
Q4226A
Q4223A
Q4227A
QS4224A
QS4226A
QS4223A
QS4227A
N4324A
N4323A
N4327A
H4224B
N/A
N/A
N/A
HL4124B
N/A
N/A
N/A
K4124B
N/A
N/A
N/A
KK4124B
N/A
N/A
N/A
L4124B
N/A
LQ4124B
N/A
N/A
N/A
LL4124B
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
38
38
38
38
38
38
38
38
50
50
50
50
50
50
50
50
50
50
65
65
65
65
75
75
75
75
75
75
75
75
100
100
100
100
150
150
150
150
150
150
150
3.4
3.4
3.4
2.3
6.8
6.8
6.8
4.5
18
18
18
11
23
23
23
15
31
31
31
31
31
20
32
32
32
25
45
45
45
36
68
68
68
45
114
114
114
73
136
136
136
1450
1450
1450
950
1450
1450
1450
950
780
780
780
520
780
780
780
520
640
640
640
640
640
420
520
520
520
420
640
640
640
520
520
520
520
350
520
520
520
350
350
350
350
R324A
R323A
R327A
RS324A
RS323A
RS327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
N/A
N/A
N/A
N/A
N/A
N/A
200
200
200
254
254
254
250
250
250
364
364
364
280
280
280
280
280
280
Max.
Hydrostatic
Pressure
Max
Discharge
Pressure for
22 cSt Liquid
at rated
speed
BAR
BAR
Packed
14
28
28
28
28
28
28
28
28
28
28
28
28
28
Steel Fitted
Const.
Recommended
Above
Approx.
Shipping
Weight with
Valve
Mech
Seal
cSt
KG
232
232
5,500
10
191
191
N/A
14
232
232
1,650
10
191
191
N/A
14
232
232
5,500
10
177
177
N/A
14
232
232
5,500
10
177
177
N/A
14
232
232
5,500
14
232
232
5,500
10
177
177
N/A
14
232
232
550
10
177
177
N/A
14
232
232
16,500
163
163
N/A
14
232
232
1,650
121
121
N/A
14
232
232
16,500
Max
Recommended
Temp. for Standard
Pump (oC)
121
121
N/A
14
132
150
16,500
14
79
79
N/A
14
232
107
5,500
12
79
79
N/A
232
107
16,500
79
79
N/A
19
19
19
21
20
20
20
24
54
54
54
57
57
57
57
59
79
79
86
86
86
95
91
91
95
116
95
95
95
104
218
218
222
227
265
265
268
272
367
367
367
651
651
651
718
718
718
NOTE: The N size is standard with a jacketed bracket and non-jacketed head and non-jacketed relief valve, while the R size is standard with a jacketed bracket, a
jacketed head, and a non-jacketed relief valve. RS contact factory for jacketing options.
For maximum recommended discharge pressures at different viscosities,
see performance curves. If suction pressure exceeds 50 PSIG, consult
factory.
Higher temperatures can be handled with special construction. Consult
factory.
Ports are tapped for standard (NPT) pipe.
Ports are suitable for use with 125# ANSI cast iron flanges or flanged fittings.
Ports are suitable for 150# ANSI steel or stainless steel companion flanges
or flanged fittings.
Port sizes are inch standard, not metric design or size. See p.630.16 for
other port size options.
Temperature based on PTFE seal as standard. Lower temperature limits
may be required when using other seal elastomers.
2007
Section
630
Page
630.17
Issue
H224A
H226A
H223A
H227A
HL224A
HL226A
HL223A
HL227A
K224A
K226A
K223A
K227A
KK224A
KK226A
KK223A
KK227A
L224A/AE
L226A
LQ224A/AE
LQ226A
LQ223A
LQ227A
LL224A/AE
LL226A
LL223A
LL227A
LS224A
LS226A
LS223A
LS227A
Q224A
Q226A
Q223A
Q227A
QS224A
QS226A
QS223A
QS227A
N324A
N323A
N327A
R324A
R323A
R327A
RS324A
RS323A
RS327A
H4224A
H4226A
H4223A
H4227A
HL4224A
HL4226A
HL4223A
HL4227A
K4224A
K4226A
K4223A
K4227A
KK4224A
KK4226A
KK4223A
KK4227A
L4224A/AE
L4226A
LQ4224A/AE
LQ4226A
LQ4223A
LQ4227A
LL4224A/AE
LL4226A
LL4223A
LL4227A
LS4224A
LS4226A
LS4223A
LS4227A
Q4224A
Q4226A
Q4223A
Q4227A
QS4224A
QS4226A
QS4223A
QS4227A
N4324A
N4323A
N4327A
R4324A
R4323A
R4327A
RS4324A
RS4323A
RS4327A
Behind the
Rotor Seal
H4224B
N/A
N/A
N/A
HL4224B
N/A
N/A
N/A
K4224B
N/A
N/A
N/A
KK4224B
N/A
N/A
N/A
L4224B
N/A
LQ4224B
N/A
N/A
N/A
LL4224B
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Standard Jacketed
Pumps Standard
Ports
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
4
4
4
4
6
6
6
6
6
6
6
8
8
8
10
10
10
Fully-Jacketed Casings
1.5, 2
2
2
2
1.5, 2
2
2
2
2,2.5 ,3 ,4
4
4
2,2.5 ,3 ,4
3 ; 4 ; 3; 3
3 ; 4 ; 3 ; 3
4
4
3 ; 4 ; 3; 3
3 ; 4 ; 3 ; 3
3 , 4 , 6
3
3
4, 5
3 ; 3 ; 4
3 ; 3 ; 4
4
4
4
3, 5, 6
4 ; 6 ; 4
4 ; 6 ; 4
4 ; 4
4 ; 4
6
6 ; 6
6 ; 6
5 ; 6
6 ; 8
6 ; 8
8
8
Standard port configuration is 90 which may be rotated (H-Q) or opposite (QS). with right hand inlet viewed from the shaft end.
Contact factory for flange details (e.g. Flat face or raised face flanges)
* Standard-Jacketed Pumps have a jacketed bracket and head, but the casing is
not jacketed. They have the series designations 224A/4224A & AE, 226A/4226A,
223A/4223A, and 227A/4227A. Also the N324A, N4324A, N323A, N4324A,
N327A and N4327A are standard with a jacketed bracket and non-jacketed
head and Relief Valve, while the R324A, R4324A, R323A, R4323A, N327A, and
R4327A are standard with a jacketed bracket and jacketed head and non-jacketed
Relief Valve. Fully-Jacketed pumps use the Standard-Jacketed Pumps series
designation, but substitute a Fully-Jacketed Casing from the list above instead of
the Standard-Jacketed Pumps non-jacketed casing.
2007
Section
630
Page
630.18
Issue
Stuffing Box
Seal
H224A
HL224A
H226A
H4224A
HL4224A
H4226A
HL226A
HL4226A
H223A
H4223A
HL223A
HL4223A
H227A
H4227A
HL227A
K224A
KK224A
K226A
HL4227A
K4224A
KK4224A
K4226A
KK226A
KK4226A
K223A
K4223A
KK223A
KK4223A
K227A
K4227A
KK227A
L224A/AE
L226A
LQ224A/AE
LQ226A
KK4227A
L4224A/AE
L4226A
LQ4224A/AE
LQ4226A
LQ223A
LQ4223A
LQ227A
LL224A/AE
LL226A
LQ4227A
LL4224A/AE
LL4226A
LL223A
LL4223A
LL227A
LL4227A
LS224A
LS4224A
LS226A
LS4226A
LS223A
LS4223A
LS227A
LS4227A
Q224A
Q4224A
Q226A
Q4226A
Q223A
Q4223A
Q227A
Q4227A
Behind
the Rotor
Seal
H4224B
HL4224B
1.5
1.5
K4224B
KK4224B
L4224B
LQ4224B
2
2.5
2.5
LL4224B
in
3.00
4.75
3.50
2.75
2.25
6.75
3.50
mm
76.2
120.6
88.9
69.8
57.1
171.4
in
4.00
4.75
3.50
2.75
2.25
mm 101.6
120.6
88.9
69.8
5.12
8.00
5.50
mm 130.0
3
3
3
3
4
4
0.47
0.99
3.38
2.38
4.00
0.56
88.9
11.9
25.1
85.8
60.5
101.6
14.2
6.75
3.50
0.47
0.99
3.38
2.38
4.00
0.56
57.1
171.4
88.9
11.9
25.1
85.8
60.5
101.6
14.2
4.00
2.75
9.25
4.00
0.53
1.42
3.00
4.00
5.75
0.62
203.2
139.7 101.6
69.8
234.9
101.6
13.5
36.1
76.2
101.6
146.0
15.7
5.25
8.00
5.50
4.00
2.75
9.25
4.00
0.53
1.42
3.00
4.00
5.75
0.62
mm 133.3
203.2
139.7 101.6
69.8
234.9
101.6
13.5
36.1
76.2
101.6
146.0
15.7
in
6.50
mm 165.1
in
7.19
mm 182.6
10.25
260.3
10.25
260.3
7.00
177.8
7.00
177.8
5.38
136.7
5.38
136.7
0.53
13.5
0.53
13.5
2
50.8
2
50.8
3.38
85.9
3.38
85.9
5.12
130.0
5.12
130.0
6.56
166.6
6.56
166.6
0.62
15.7
0.62
15.7
A
(in)
in
in
7.19
10.25
7.00
4.38
10.00
5.38
0.53
3.38
5.12
6.56
0.62
mm 182.6
in
7.19
mm 182.6
in
260.3
10.25
260.3
177.8
7.00
177.8
136.7
5.38
136.7
13.5
0.53
13.5
50.8
2
50.8
85.9
3.38
85.9
130.0
5.12
130.0
166.6
6.56
166.6
15.7
0.62
15.7
in
4.00
7.19
10.25
7.00
4.38
mm 182.6
260.3
177.8
111.3 101.6
7.19
10.25
7.00
4.38
mm 182.6
260.3
177.8
111.3 101.6
7.19
10.25
7.00
4.38
mm 182.6
260.3
177.8
111.3 101.6
8.25
14.00
8.75
4.12
mm 209.5
355.6
in
in
in
4.00
4.00
4.00
4.00
10.00
5.38
0.53
3.38
5.12
6.56
0.62
254
136.7
13.5
50.8
85.9
130.0
166.6
15.7
10.00
5.38
0.53
2.55
4.75
5.12
7.40
0.62
254
136.7
13.5
64.8
120.6
130.0
188.0
15.7
10.00
5.38
0.53
2.55
4.75
5.12
7.40
0.62
254
136.7
13.5
64.8
120.6
130.0
188.0
15.7
10.00
6.00
0.69
3.58
6.62
7.00
7.62
0.75
254
152.4
17.5
90.9
168.1
177.8
193.5
19.0
2007
Section
630
Page
630.19
Issue
Model Number
Packed
Stuffing Box
Seal
H224A
HL224A
H226A
HL226A
H223A
HL223A
H227A
HL227A
K224A
H4224A
HL4224A
H4226A
HL4226A
H4223A
HL4223A
H4227A
HL4227A
K4224A
KK224A
KK4224A
K226A
KK226A
K223A
KK223A
K227A
KK227A
K4226A
KK4226A
K4223A
KK4223A
K4227A
KK4227A
L224A/AE
L4224A/AE
L226A
L4226A
Behind
the Rotor
Seal
H4224B
HL4224B
K4224B
KK4224B
L4224B
12.06
1.62
0.75
.19 X .09
101.6
306.3
41.1
19.0
0.62
4.00
12.06
1.62
0.75
.19 X .09
mm
15.7
101.6
306.3
41.1
in
0.62
5.75
16.38
mm
15.7
146.0
in
0.62
mm
15.7
EE
FF
in
0.62
4.00
4.04 1.80
2.41
5.75
2.30
mm
15.7
61.2
146.0
58.4
in
4.04 1.80
2.41
5.75
2.30
19.0
61.2
146.0
58.4
2.25
1.12
.25 X .12
7.00 3.38
3.25
6.75
2.92
416.0
57.1
28.4
82.5
171.4
74.2
5.75
16.38
2.25
1.12
7.00 3.38
3.25
6.75
2.92
146.0
416.0
57.1
28.4
82.5
171.4
74.2
3.25 1.25
3.00
3.81
6.75
2.93
96.8
171.4
74.4
in
0.62
6.56
17.88
2.25
1.12
mm
15.7
166.6
454.2
57.1
28.4
in
0.62
6.56
17.88
2.25
1.12
mm
15.7
166.6
454.2
57.1
28.4
LQ4223A
in
0.62
6.56
17.88
2.25
1.12
LQ4227A
mm
15.7
166.6
454.2
57.1
28.4
LQ226A
LQ4226A
LQ223A
LQ227A
LL224A/AE
LL4224A/AE
LL226A
LL4226A
LL223A
LL227A
LS224A
LS4224A
LS226A
LS4226A
LS223A
LS227A
Q224A
Q226A
Q223A
Q227A
LS4223A
LS4227A
Q4224A
Q4226A
Q4223A
Q4227A
LL4224B
.25 X .12
.25 X .12
.25 X .12
7.18 4.62
AA
3.00
3.81
6.75
2.93
96.8
171.4
74.4
3.00
3.81
6.75
2.93
96.8
171.4
74.4
4.31
6.75
2.93
6.35 X 3.05 182.4 117.3 82.5 31.7 25.4 76.2 109.5 171.4
74.4
in
0.62
6.56
17.88
2.25
1.12
15.7
166.6
454.2
57.1
28.4
LL4223A
in
0.62
6.56
17.88
2.25
1.13
LL4227A
mm
15.7
166.6
454.2
57.1
28.4
in
0.62
7.00
19.25
3.50
1.44
.38 X .19
4.50
7.00
4.03
mm
15.7
177.8
488.9
88.9
36.58
177.8
102.4
in.
1.00
6.62
23.75
4.50
1.94
.50 X .25
mm
25.4
168.1
603.2
114.3
49.3
7.18 4.62
3.25 1.25
mm
.25 X .12
7.18 4.62
3.25 1.25
7.18 4.62
3.25 1.25
BB
7.18 4.62
DD
CC
6.75
2.93
74.4
11.25 5.50
3.30 1.25
4.50
1.5
3.00
6.35 X 3.05 182.4 117.3 82.5 31.7 25.4 76.2 109.5 171.4
7.72 4.40
3.25 1.25
3.00
3.00
4.31
1.25
---
4.57
8.38
5.35
---
116.1
212.8
135.9
Ports for steam or hot oil jacketing are inch standard NPT threads. Metric (mm) equivalents are for information only, and do not indicate a metric thread size.
T dimension show for Cast Iron sizes L,LQ and LL is for A models. Dimension for L, LQ and LL size 224AE, 4224AE and 4224B pumps is 2.35 (59.7 mm).
U dimension shown for Cast Iron sizes L, LQ and LL is for A models. U dimension for L, LQ and LL size 224AE, 4224AE and 4224B pumps is 1.44 (36.6 mm).
V dimension shown for Cast Iron sizes L, LQ and LL is for A models. V dimension for L, LQ and LL size 224AE, 4224AE and 4224B pumps is 0.38 X 0.19
(9.65 X 4.83 mm).
BB Dimension for Q223A and Q227A is 1(25.4 mm).
2007
Section
630
Page
630.20
Issue
Model Number
Packed
Mechanical Seal
QS224A
QS4224A
QS226A
QS4226A
QS223A
QS4223A
QS227A
QS4227A
BB*
DD
GG
1.25 (31.75)
5.57 (141.48)
4.12 (105)
1 (25.4)
6.06 (152.93)
3.75 (95.25)
* Ports for steam or hot oil jacketing are inch standard NPT threads. Metric (mm) equivalents are for information only, and do not indicate a metric thread size.
2007
Section
630
Page
630.21
Issue
Model Number
A
(in)
Packed
Stuffing
Box Seal
N324A
N323A
N327A
N4324A
N4323A
N4327A
R324A
R323A
R327A
R4324A
R4323A
R4327A
RS324A RS4324A
RS323A RS4323A
RS327A RS4327A
10
B
in
5.00
6.25
8.69
1.62
0.69
O
1.00
6.00
2.44
.62x.31
8.63
0.69
N/A 18.94
219.2 17.5
N/A 481.0
3.44
1.25 19.25
168.1 87.4
22.35
304.8 17.5
x11.18
31.7 488.9
6.62
1.25 19.25
0.78
1.00
1.30
1041
6.62
3.44
mm 361.9 622.30 336.5 171.4 177.8 333.24 122.17 22.35 152.4 418.08 206.24 33.02 114.3 725.17 1104.64 168.1 87.4
15.74
x7.87
22.35
304.8 22.35 31.7 488.9
x11.18
NOTE: The N size is standard with a jacketed bracket and non-jacketed head and non-jacketed relief valve, while the R size is standard with a jacketed
bracket, a jacketed head, and a non-jacketed relief valve. RS contact factory for jacketing options.
Ports are suitable for use with 125# ANSI cast iron (324A/4324A) or 150# ANSI steel or stainless steel companion flanges or flanged fittings (323A/4323A & 327A/
4327A).
2007
Section
630
Page
630.22
Issue
Pump Size
H & HL
K & KK
L, LQ, & LL
(A)
L, LQ, & LL
(AE)
LS
Q & QS
R & RS
In
1.12
2.00
2.41
2.22
1.90
1.03
2.27
4.50
3.00 to 3.50
2.00
2.50
4.00
0.66
5/16
4.47
1/8
mm
28.6
50.8
61.2
56.4
48.3
26.2
57.7
114.3
76.2 to 88.9
50.8
63.5
101.6
16.8
7.9
113.5
3.2
In
1.44
2.31
3.00
3.13
2.25
1.25
3.00
5.25
3.50 to 4.50
2.50
3.00
5.00
0.38
7/16
5.25
1/4
mm
36.5
58.7
76.2
79.5
57.1
31.7
76.2
133.3
88.9 to 114.3
63.5
76.2
127.0
9.7
11.1
133.3
6.3
In
1.44
2.31
3.00
3.13
2.25
1.25
4.00
5.25
3.50 to 4.50
2.50
3.00
5.00
0.44
7/16
5.25
1/4
mm
36.5
58.7
76.2
79.5
57.1
31.7
101.6
133.3
88.9 to 114.3
63.5
76.2
127.0
11.2
11.1
133.3
6.3
In
1.62
2.375
3.00
3.13
2.25
1.16
3.52
5.25
3.50 to 4.50
3.00
3.00
5.00
0.46
7/16
5.25
1/4
mm
41.3
60.3
76.2
79.5
57.1
29.5
89.4
133.3
88.9 to 114.3
76.2
76.2
127.0
11.7
11.1
133.3
6.3
In
1.62
2.375
2.80
2.70
2.25
1.16
3.52
5.25
3.25 to 4.50
3.00
2.80
5.00
0.46
7/16
5.25
1/4
mm
41.3
60.3
71.1
68.6
57.1
29.5
89.4
133.3
82.5 to 114.3
76.2
71.1
127.0
11.7
11.1
133.3
6.3
In
2.44
3.42
4.50
4.00
2.50
1.53
4.10
6.75
5.50 to 6.25
3.20
4.50
7.20
0.56
5/8
6.75
1/4
mm
61.9
87.0
114.3
101.6
63.5
38.9
104.1
171.4
139.7 to 158.7
81.3
114.3
182.9
14.2
15.9
171.4
6.3
In
3.44
4.69
5.56
1.65
4.91
8.81
6.75
3/4
9.00
1/4
mm
87.3
119.3
141.2
41.9
124.7
223.8
171.4
19.0
228.6
6.3
In
4.50
5.75
5.56
1.53
4.79
9.81
7.75
3/4
9.81
1/4
mm
114.3
146.1
141.2
38.9
121.7
249.2
196.8
19.0
249.2
6.3
Bracket is counter bored to a diameter of 2.687 inches (68.25 mm), 0.12 inches (3.05 mm) deep from stuffing box face.
Studs are used in place of cap screws.
2007
Section
630
Page
630.23
Issue
Quick Pick Chart Maximum Operating Conditions (Cast & Ductile Iron Series)
38 SSU
(4 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
Speed (RPM)
13.5
100
1750
28
100
1750
75
100
780
96
100
780
133
100
640
135
100
520
192
100
640
270
100
520
440
100
520
480
100
350
870
100
280
1377
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
3.1
7
1, 2
6.4
7
13, 14
17.0
7
25, 26
22
7
37, 38
30
7
49, 50
31
7
61, 62
44
7
73, 74
61
7
85, 86
100
7
97
109
7
105
198
7
113
313
7
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
Speed (RPM)
15
200
1750
31
200
1750
77
200
780
102
200
780
141
200
640
143
200
520
204
150
640
296
150
520
460
150
520
520
150
350
965
150
280
1493
Flow (M3/Hr)
3.4
14
3, 4
7.0
14
15, 16
17.5
14
27, 28
23
14
39, 40
32
14
51, 52
32
14
63, 64
46
10
75, 76
67
10
87, 88
104
10
98
118
10
106
219
10
114
339
10
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
Speed (RPM)
17
200
1750
32
200
1750
79
200
780
105
200
780
146
200
640
149
200
520
565
200
350
1180
175
280
1551
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
3.9
14
5, 6
7.3
14
17, 18
17.9
14
29, 30
24
14
41, 42
33
14
53, 54
34
14
65, 66
47/31
10/14
77, 78
68/45
10/14
89, 90
128
14
107
268
12
115
352
12
2,500 SSU
(5,500 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
Speed (RPM)
10.5
200
1150
21.5
200
1150
51
200
520
69
200
520
115
200
520
146
200
520
175
200
520
262
200
420
385
200
420
570
200
350
1185
200
280
1625
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
2.4
14
7, 8
4.9
14
19, 20
11.6
14
31, 32
15.7
14
43, 44
26
14
55, 56
33
14
67, 68
40
14
79, 80
60
14
91, 92
87
14
100
129
14
108
269
14
116
369
14
7,500 SSU
(1,650 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
Speed (RPM)
10.5
200
1150
21.2
200
1150
43
200
420
56
200
420
95
200
420
119
200
420
145
200
420
220
200
350
325
200
350
460
200
280
905
200
230
1342
2.4
14
9
4.8
14
21
9.8
14
33
12.7
14
45
22
14
57
27
14
69
33
14
81
50
14
93
74
14
101
104
14
109
206
14
117
304
100 SSU
(22 cSt)
Pressure (BAR)
See Curve # 630-
750 SSU
(165 cSt)
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
* N and R and RS Sizes Available in Cast Iron, but not Ductile Iron
To generate performance curves, please use the Pump Selector program available through www.IDEXconnect.com(security passwords required).
2007
100
280
125
280
125
280
125
280
125
230
14
Section
630
Page
630.24
Issue
Quick Pick Chart Maximum Operating Conditions (Cast & Ductile Iron Series)
25,000 SSU
(5,500 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
8.8
200
17
200
36
200
48
200
82
200
100
200
122
200
175
200
260
200
380
200
750
200
1108
Speed (RPM)
950
950
350
350
350
350
350
280
280
230
190
190
Flow (M3/Hr)
2.0
3.9
8.2
10.9
18.6
23
28
40
59
86
170
252
Pressure (BAR)
See Curve # 630-
14
10
14
22
14
34
14
46
14
58
14
70
14
82
14
94
14
102
14
110
14
118
14
75,000 SSU
(16,500 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
Flow (GPM)
Pressure (PSI)
7.2
200
11.5
200
23.2
200
31
200
53
200
67
200
80
200
120
200
175
200
263
200
490
200
730
Speed (RPM)
780
640
230
230
230
230
230
190
190
155
125
125
Flow (M3/Hr)
1.6
2.6
5.3
7.0
12.0
15.2
18.2
27
40
60
111
166
Pressure (BAR)
See Curve # 630-
14
11
14
23
14
35
14
47
14
59
14
71
14
83
14
95
14
103
14
111
14
119
14
250,000 SSU
(55,000 cSt)
HL
KK
L, LQ
LL
LS
QS
N*
R*
RS*
16
200
155
21
200
155
35
200
155
45
200
155
53
200
155
96
200
155
214
200
125
340
200
84
494
3.6
14
36
4.8
14
48
7.9
14
60
10.2
14
72
12.0
14
84
22
14
96
49
14
112
77
14
120
112
14
Flow (GPM)
Pressure (PSI)
Speed (RPM)
4.1
200
420
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
0.9
14
12
Contact
Factory
24
Contact
Factory
104
* N and R, and RS Sizes Available in Cast Iron, but not Ductile Iron
To generate performance curves, please use the Pump Selector program available through www.idexconnect.com (security passwords required).
2007
125
125
125
84
Section
630
Page
630.25
Issue
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
13.5
100
1750
27.5
100
1750
50
100
640
70
100
640
125
100
640
125
100
520
190
100
640
270
100
520
440
100
520
430
75
350
690
75
230
1120
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
3.1
7
121
6.2
7
129
11.4
7
137
15.9
7
145
28
7
153
28
7
161
43
7
169
61
7
177
100
7
185
98
5
193
157
5
201
254
5
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
14.5
200
1750
30
200
1750
56
200
640
75
200
640
136
200
640
136
200
520
200
150
640
295
150
520
460
150
520
485
125
350
765
125
230
1200
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
3.3
14
122
6.8
14
130
12.7
14
138
17.0
14
146
31
14
154
31
14
162
45
10
170
67
10
178
104
10
186
110
8.5
194
174
8.5
202
275
8.5
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
15.8
200
1750
27
200
1750
61
200
640
81
200
640
136
200
640
144
200
520
565
200
350
1020
175
280
1551
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
3.6
14
123
6.1
14
131
13.9
14
139
18.4
14
147
31
14
155
33
14
163
47/30
10/14
171
72/45
10/14
179
107/74
10/14
187
128
14
195
232
12
203
352
8.5
2,500 SSU
(5,500 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
10.5
200
1150
21.2
200
1150
51
200
520
69
200
520
116
200
520
146
200
520
175
200
520
262
200
420
390
200
420
570
200
350
1045
175
280
1625
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
2.4
14
124
4.8
14
132
11.6
14
140
15.7
14
148
26
14
156
33
14
164
40
14
172
60
14
180
89
14
188
129
14
196
237
12
204
369
8.5
7,500 SSU
(1,650 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
10.6
200
1150
21.2
200
1150
43
200
420
56
200
420
95
200
420
119
200
420
139
200
420
220
200
350
330
200
350
460
200
280
880
175
230
1342
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
2.4
14
125
4.8
14
133
9.8
14
141
12.7
14
149
22
14
157
27
14
165
32
14
173
50
14
181
75
14
189
104
14
197
200
12
205
305
8.5
100 SSU
(22 cSt)
750 SSU
(165 cSt)
To generate performance curves, please use the Pump Selector program available through www.idexconnect.com (security passwords required).
2007
75
230
125
230
125
280
125
280
125
230
Section
630
Page
630.26
Issue
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
9
200
950
17.2
200
950
36
200
350
48
200
350
82
200
350
101
200
350
122
200
350
175
200
280
262
200
280
380
200
230
730
175
190
1108
Flow (M3/Hr)
2.0
3.9
8.2
10.9
18.6
23
28
40
60
86
166
252
Pressure (BAR)
14
14
14
14
14
14
14
14
14
14
12
8.5
126
134
142
150
158
166
174
182
190
198
206
75,000 SSU
(16,500 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
7.2
200
11.3
200
23.5
200
30.5
200
52.5
200
66.5
200
80
200
120
200
175
200
253
200
485
175
730
125
Speed (RPM)
780
640
230
230
230
230
230
190
190
155
125
125
Flow (M /Hr)
Pressure (BAR)
See Curve # 630-
1.6
14
127
2.6
14
135
5.3
14
143
6.9
14
151
11.9
14
159
15.1
14
167
18.2
14
175
27
14
183
40
14
191
57
14
199
110
12
207
166
8.5
250,000 SSU
(55,000 cSt)
HL
KK
LQ
LL
LS
QS
RS
16
200
155
21
150
155
35
200
155
45
200
155
53
200
155
96
200
155
214
200
125
325
175
84
494
3.6
14
144
4.8
10
152
7.9
14
160
10.2
14
168
12.0
14
176
22
14
184
49
14
200
74
12
208
112
8.5
Flow (GPM)
Pressure (PSI)
Speed (RPM)
4.1
200
420
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
0.9
14
128
Contact
Factory
136
Contact
Factory
192
To generate performance curves, please use the Pump Selector program available through www.idexconnect.com (security passwords required).
2007
125
190
125
84
Section
630
Page
630.27
Issue
Quick Pick Chart Maximum Operating Conditions (Stainless Steel Externals Series)
38 SSU
(4 cSt)
HL
KK
LQ
LL
LS
QS
RS
8.2
50
17.5
50
31
50
48
50
80
50
105
50
150
50
173
50
235
50
430
75
690
75
1120
Speed (RPM)
1150
1150
420
420
420
420
520
350
280
350
230
230
Flow (M3/Hr)
1.9
4.0
7.0
10.9
18.2
24
34
39
53
98
157
254
Pressure (BAR)
See Curve # 630-
3.4
209
3.4
217
3.4
225
3.4
233
3.4
241
3.4
249
3.4
257
3.4
265
3.4
273
5
281
5
289
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
8.8
100
19.5
100
34
100
50
100
82
100
104
100
160
100
187
100
245
100
485
125
765
125
1200
Speed (RPM)
1150
1150
420
420
420
420
520
350
280
350
230
230
Flow (M3/Hr)
2.0
4.4
7.7
11.4
18.6
24
36
42
56
110
174
275
Pressure (BAR)
See Curve # 630-
7
210
7
218
7
226
7
234
7
242
7
250
7
258
7
266
7
274
8.5
282
8.5
290
8.5
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
9.8
100
20.5
100
40.5
100
55
100
92
100
112
100
172
100
205
100
255
100
565
200
1020
175
1551
Speed (RPM)
1150
1150
420
420
420
420
520
350
280
350
280
280
Flow (M3/Hr)
2.2
4.7
9.2
12.5
21
25
39
47
58
128
232
352
Pressure (BAR)
See Curve # 630-
7
211
7
219
7
227
7
235
7
243
7
251
7
259
7
267
7
275
14
283
12
291
8.5
2,500 SSU
(5,500 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
10.4
150
21
150
42
150
56
150
93
150
96
150
175
125
220
125
275
125
570
200
1045
175
1625
Speed (RPM)
1150
1150
420
420
420
350
520
350
280
350
280
280
Flow (M3/Hr)
2.4
4.8
9.5
12.7
21
22
40
50
62
129
237
369
Pressure (BAR)
See Curve # 630-
10
212
10
220
10
228
10
236
10
244
10
252
8.5
260
8.5
268
8.5
276
14
284
12
292
8.5
7,500 SSU
(1,650 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
8.5
150
17
150
35
150
36.5
150
80
150
77
150
145
125
220
125
285
125
460
200
880
175
1342
Speed (RPM)
950
950
350
280
350
280
420
350
280
280
230
230
Flow (M3/Hr)
1.9
3.4
7.9
8.3
18.2
17.5
33
50
65
104
200
305
Pressure (BAR)
See Curve # 630-
10
213
10
221
10
229
10
237
10
245
10
253
8.5
261
8.5
269
8.5
277
14
285
12
293
8.5
Flow (GPM)
Pressure (PSI)
100 SSU
(22 cSt)
750 SSU
(165 cSt)
To generate performance curves, please use the Pump Selector program available through www.idexconnect.com (security passwords required).
2007
75
125
125
125
125
Section
630
Page
630.28
Issue
Quick Pick Chart Maximum Operating Conditions (Stainless Steel Externals Series)
25,000 SSU
(5,500 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
7
150
14.2
150
28
150
36.5
150
62.5
150
64
150
122
125
175
125
240
125
380
200
730
175
1108
Speed (RPM)
780
780
280
280
280
230
350
280
230
230
190
190
Flow (M3/Hr)
1.6
3.2
6.4
8.3
14.2
14.5
28
40
55
86
166
252
Pressure (BAR)
See Curve # 630-
10
214
10
222
10
230
10
238
10
246
10
254
8.5
262
8.5
270
8.5
278
14
286
12
294
8.5
75,000 SSU
(16,500 cSt)
HL
KK
LQ
LL
LS
QS
RS
Flow (GPM)
Pressure (PSI)
Speed (RPM)
Flow (M3/Hr)
Pressure (BAR)
See Curve # 630-
5.7
150
640
1.3
10
215
11
150
640
2.5
10
223
23
150
230
5.2
10
231
30
150
230
6.8
10
239
52.5
150
230
11.9
10
247
54.5
150
190
12.4
10
255
80
125
230
18.2
8.5
263
120
125
190
27
8.5
271
160
125
155
36
8.5
279
253
200
155
57
14
287
485
175
125
110
12
295
730
250,000 SSU
(55,000 cSt)
HL
KK
LQ
LL
LS
QS
RS
16
150
19.5
150
34.2
150
53
125
96
125
130
125
214
200
325
175
494
155
155
155
155
155
125
125
84
84
3.6
4.4
7.8
12.0
22
30
49
74
112
10
232
10
240
10
248
8.5
264
8.5
272
8.5
280
14
288
12
296
8.5
Flow (GPM)
Pressure (PSI)
3.8
150
Speed (RPM)
420
Flow (M3/Hr)
0.9
Pressure (BAR)
See Curve # 630-
10
216
Contact
Factory
224
Contact
Factory
256
To generate performance curves, please use the Pump Selector program available through www.idexconnect.com (security passwords required).
2007
125
125
125
166
8.5
125