Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SP3D : Contents
Introduction Cable Ladder & Cable Tray OE Cable Ladder System FOE Cable Ladder System LOE Cable Ladder System FTE Cable Tray System SPB Cable Tray System SP3D Oglaend Reports SP3D Oglaend Specifications Set-up
3 - 11 12 - 22 23 - 33 34 - 46 47 - 53 54 - 63 64 - 66 67 - 78
SP3D representation
Based on SP3D Cable part definition : Allowing easy change of SP3D specification Selection of Cable Ladder and Tray types L di of Loading f particular i l specification ifi i to cover customer project j requirements i Recommended work flow Read the following information Choose the specifications required for your project Refer to the load instructions at the end of this document
SP3D representation
Standard length : 3 metres OE offered in material finishes of : Hot Dipped Galvanized (HDG) Stainless Steel (SS) LOE offered in material finishes of : Hot Dipped Galvanized (HDG) Stainless St i l St Steel l (SS) Pre-Galvanized (PG) FOE offered in material finishes of: Polyester Resin
FOE
All SP3D specification types being designed for open requirements only
2012. Intergraph Process, Power & Marine. All Rights Reserved.
LOE
FOE
LOE
SP3D representation
Cable Ladder systems Un-Lidded FTE SPB FTE-50, FTE-80 SPB-20, SPB-40, SPB-RF
FTE
FTE offered in material finishes of : Polyester Resin (C1, C2) SPB offered in material finishes of : Hot Dipped Galvanized (HDG) Stainless Steel (SS) Pre-Galvanized (PG) SPB SPB-RF RF offered in material finishes of: Hot Dipped Galvanized (HDG) Stainless Steel (SS)
SPB
SPB-RF
All SP3D specification types being designed for open requirements only
2012. Intergraph Process, Power & Marine. All Rights Reserved.
FTE SPB
Lidded specifications have a CO in their name to designate Covered. The covers are implied and have no graphical representation FTE offered in material finishes of : Polyester Resin (C1, C2) SPB offered in material finishes of : Hot Dipped Galvanized (HDG) Stainless Steel (SS) Pre-Galvanized (PG) ( ) SPB-RF offered in material finishes of: Hot Dipped Galvanized (HDG) Stainless Steel (SS)
SPB
SPB-RF
All SP3D specification types being designed for open requirements only
2012. Intergraph Process, Power & Marine. All Rights Reserved.
The specification is designed to place OE fittings in both manual and sketch modes Understanding of the specification is imperative to efficient construction and material purchase h Falling into two remits : Sketch mode : being the most effective manner to place Manual mode : used in restricted environments allowing manual modification and selection of individual fittings
Flexi Riser
Combi Riser
The specification is designed to place FOE fittings in both manual and sketch modes Understanding of the specification is imperative to efficient construction and material purchase h Falling into two remits : Sketch mode : being the most effective manner to place Manual mode : used in restricted environments allowing manual modification and selection of individual fittings
Offset Reducer
Central Reducer
Reducer Part
Riser Bracket
Combi Riser
The specification is designed to place FTE fittings in both manual and sketch modes Understanding of the specification is imperative to efficient construction and material purchase h Falling into two remits : Sketch mode : being the most effective manner to place Manual mode : used in restricted environments allowing manual modification and selection of individual fittings
Combi Riser
The specification is designed to place SPB fittings in both manual and sketch modes Understanding of the specification is imperative to efficient construction and material purchase h Falling into two remits : Sketch mode : being the most effective manner to place Manual mode : used in restricted environments allowing manual modification and selection of individual fittings Note the following g information for SPB specifications : 55mm must be added to the straight length to accommodate fitting to straight joints. This is to allow for the straight insertion depth when a straight is connected to a Tee, Flat Bend or Cross. For example example, a straight length between two flat bends means a total of 110mm being added to the straight length.
2012. Intergraph Process, Power & Marine. All Rights Reserved.
Combi Riser
Central Reducer
SP3D : Oglaend Catalogue : Reporting Oglaend Cable Ladder & Tray SP3D Specification - Reporting
3 Reports supplied: Oglaend g Fittings g Report p Oglaend Cover Report Oglaend Splice Report SP3D representation
2012. Intergraph Process, Power & Marine. All Rights Reserved.
SP3D representation
2012. Intergraph Process, Power & Marine. All Rights Reserved.
Creating SP3D Catalogue (optional for existing project ) Loading SP3D symbols Project Creation (Optional not covered in document) Updating the Catalogue with the particular specification files R l ti S Relating Specification ifi ti t to SP3D systems t Setting up delivered reports
Oglaend Final Deliverables \SmartPlant \FOE Final Deliverable (Contains FOE specifications, code lists and custom symbols) \FTE Final Deliverable \LOE Final Deliverable \OE Final Deliverable (Contains FTE specifications , code lists and custom symbols) (Contains LOE specifications, code lists and custom symbols) (Contains OE specifications , code lists and custom symbols)
\SPBE Final Deliverable (Contains SPBE specifications, code lists and custom symbols) \Reports \PPTS (Contains Custom report templates and DLL) (General overview of use and how to load)
Using and existing specification Normal to use for change from one specification to another Allows change from existing specification to another
Catalogue schema name : ensure this is unique in your database Template file : point to your default template supplied
SharedContent Folder (Do not use product directories for working project) Normal SP3d Administrator function Associate your catalog to the SmartPlant 3d Project.
Bulk load Specifications Open Intergraph SmartPlant 3d >Database Tools >Bulk load reference data You can find these file in the following directories :
Specification\Data\Part Data or Specification\Data\Codelist
File Type Excel Code list File name AllcodelistsFOE CableTray Select Lists Required Required by Spec. Load Function Manufacture, material, span
Required by Spec.
Oglaend_FOE2011
Required by Spec.
The icon and symbol dll where not loaded and update :- contact local Intergraph Support
Select > Specifications to relate to electrical systems Note. These may be removed / sub selected at the system Level. Loading all specifications on previous selection adds lost of parts to the database and should be avoided if not required