Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Imprint
Editor: EJOT Baubefestigungen GmbH 57334 Bad Laasphe, Germany Layout and Realisation: EJOT Baubefestigungen GmbH, 57334 Bad Laasphe, Germany Print: Vorlnder GmbH & Co. KG, 57072 Siegen, Germany Legal Notes EJOT products are constantly enhanced. We reserve the right to make changes to the technical specications as well as changes to the product range, During planning and use of our products please comply with accepted engineering rules, planning laws as well as relevant safety regulations. The national technical approvals granted to our products can be downloaded on the Internet at www.ejot.com.
Your contact:
General terms and conditions: Our general terms and conditions can also be found at www.ejot.com (footer: GTCT) 2011 by EJOT Baubefestigungen GmbH EJOT, ejotherm, Delta PT und PT are registered trademarks of EJOT GmbH & Co. KG.
www.ejot.com
CRONIMAKS, Corremaks, EJOFAST, Dabo, ECOmate FR-variotool and Solar Ready are registered trademarks of EJOT Baubefestigungen GmbH. DEKTITE is a registered trademark of Deks Industries Pty. Ltd., Bayswater Victoria, AU. TORX, TORX PLUS und AUTOSERT are registered trademarks of Acument Intellectual Properties, LLC, Troy Mich., US. Cover: Turning Torso, Malm, Sweden, iStockphoto Architect: Santiago Calatrava, Spain Supplied by EJOT Baubefestigungen GmbH: EJOT SUPER-SAPHIR self-drilling screw JT3
Contents
Service
Application advice .................. p. 6 Information ............................. p. 8 Side lap screw EJOFAST JF3 (A2 stainless steel + steel) ........ p. 53 Self-drilling screw JT3 (A2 stainless steel + steel) ........ p. 53 Self-tapping screw Corremaks JA1 / JZ1 (A5 stainless steel 1.4529) ............................................... p. 82
S el f-dri l l i ng screw s Acces sor ie s Inst al l at i on to ol s Ancho rs and Embe dmen t Tec hnol og y (Aer at ed) co ncr ete s cr ews St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo P ipe f lashings S caf f olding fast ener s D ir ect Fast ening Fa steni ng S yst . for S ol a r Inst Insta a l l laati tions os R i vets S peci a l screw s
Self-drilling screws
Side lap screw EJOFAST JF2 (steel) ...................................... p. 38 Self-drilling screw JT2 (steel) ...................................... p. 38 Self-drilling screw JT4 (A2 stainless steel) ................... p. 67
Self-tapping screw JA2 / JZ2 (steel) ...................................... p. 76 Self-tapping screw JA3 / JZ3 (A2 stainless steel) ................... p. 78
Special screws
Self-tapping screw BS-R (steel Climadur coated) ............. p. 90 Self-tapping screw JA3/JB3/JZ3 (A2 stainless steel) ................... p. 91 Self-tapping screw Duro PT (A2 stainless steel) ................... p. 95 Chip board screw SH2 (steel, Climadur coated) ............ p. 97 Closed end rivet Al/V ........... p. 103 Bulb-tite rivet ...................... p. 104 Drive rivet Al/E .................... p. 104 Chip board screw SH3 / SH3-S (Edelstahl A2) ........................... p. 97 PT Screw Type DG (for glass facades) .................... p. 99
Rivets
Blind rivet Al/E .................... p. 102 Blind rivet Al/V .................... p. 102 Blind rivet K14-Al/E............. p. 102 Closed end rivet Al/E ........... p. 103 JA3-SB Solar Fastening System ..............................................p. 107 JZ3-SB Solar Fastening System ..............................................p. 107
Direct Fastening
Shot ring tool P 525 L + Accessoires ........................ p. 109 Shot ring tool P 560 + Accessoires ........................ p. 110 Cartridges ........................... p. 111 Tie pins ................................ p. 111
Scaffolding fasteners
Scaffolding anchor JA3-GT p. 113 Scaffolding anchorJA3-GU . p. 114 Scaffolding anchor JZ3-GT . p. 113 Scaffolding anchor JZ3-GU. p. 114 Ring bolt M10 ...................... p. 113 GU Ring bolt M14 ................. p. 115 GU-threaded sleeve .............p. 115
Pipe ashings
Dektite Combo................... p. 117 Dektite Square .................. p. 118 Dektite EZi Seal ................. p. 119 Dektite Soaker .................. p. 120 Dabo A/F 8 R (steel, Climadur coated) ...........p. 128 Dabo A/F 8 RT (steel, Climadur coated) ...........p. 129 Metal stress plate HTV ........ p. 134 Metal stress plater HTV-TK . p. 134 Metal stress plate HTV-F..... p. 135 Metal stress plate HTV RU... p. 135 Concrete screw FBS-R (steel Climadur coated) ............p. 139 Aerated concrete screw FPS-E (A4 stainless steel) ................. p. 140 SDF facade anchor ............................................. p. 144 SDP facade anchor.............. p. 154 Aanchor bolt S-KA............... p. 160 Dektite Retrot.................. p. 121 Dektite Strip Flash ............ p. 122 Accessories......................... p. 123
Installation tools
Nibbler ................................. p. 170 Riveting tools ...................... p. 172 Flat roof installation tool..... p. 173 Electric screw gun .............. p. 177 FR-tool / FR-variotool ......... p. 187 Sockets / Bit holder ............ p. 188 Blow-out pump .................. p. 190 VACUtest manual pump ...... p. 190
Accessories
Sealing washer E / ES ......... p. 191 Mushromm washer ............ p. 191 Shearing load washer VS .... p. 192 Thread protection sleeve .... p. 192
Contact / Index
International contact ......... p. 196 Index................................... p. 198
Storm washers
Self-tapping screws
EJOT Your strong partner for fastening solutions in the building industry
Customer-friendly service
We make a point of building friendly and trustful relationships with our customers. Our technical consultants offer 24-hour customer service. If required our employees go directly to the building site. We also share our know-how in training seminars.
2 3
ILB
WDVS
IFF
BSA
6
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
ROOF Roof with sandwich panels page 20 page 16 ROOF Tin tile roof ROOF Double-leaf roof with seam or clamping proles page 22 page 18 ROOF Flat roof with waterproof membrane (uninsulated or insulated)
page 24
page 26
GLASS FACADE Post and rail structure WALL Single leaf proled wall page 32 page 28
page 99
SOLAR Fastening Systems for Solar Installations page 30 WALL Rear ventilated facades page 34
page 105
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Service Information
S el f-dri l l i ng screw s
PRODUCT RECOMMENDATION For the product recommendations it is assumed that the objects are buildings with no excessive demands to corrosion, load-carrying capacity or visual appearance, e.g. warehouses, ofce buildings, sales rooms etc. The recommendation does not apply to buildings with special demands on the fastening elements due to internal as well as external climatic conditions or which have special demands on the fasteners due to the location of the building. Structural-physical measures such as the application of vapour barrier sheeting or the insertion of seal strip are not addressed and they need to be considered separately. The application compass is only a suggestion without any claim to accuracy or completeness. SCREW LENGTH For determination of the minimum screw length it has to be distinguished between self-drilling screws and non self-drilling screws. For self-drilling screws the clamp thickness has to be observed. The clamp thickness of a self-drilling screw can be obtained from the product catalogue and is not part of the approval. For self-tapping fasteners without drill point the cylindrical part of the screw has to be fastened at least 6 mm into the load-bearing component. In practice 20 mm are added to the sum of the thickness of all components that are fastened onto the substructure. The result is the minimum screw length of a self-tapping screw under consideration of sealing washer and assembly unevenness.
S torm w a shers
S peci a l screw s
R i vets
tII
General
DEFINITION 1 = drill point 2 = thread intake 3 = full thread 4 = free spin zone 5 = fastener head
tI
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
a Clamp thickness
Inst al l at i on to ol s
SELF-TAPPING SCREW L = a + 20 mm
Acces sor ie s
Service Information
ROOF AND WALL MADE OF METAL PROFILE SHEETS / SANDWICH PANEL The following parameters are known: Purlin spacing or post and rail spacing The bar width of the trapezoidal profile a) Number of screws: N1 = Roof or wall area [m2] 1,2 Purlin spacing [m] 2 bar width [m]
Volume determination
GENERAL Spacing and position of the fastening elements can be obtained from the static analysis. To determine the exact number of screws is very tedious and time consuming though. A rough estimate of the required quantity is often very helpful for ordering or calculating. There are empirical values, that are expedient if an installation company always works in a similar way and orders the respective amount of fasteners. If the type of construction signicantly varies it becomes rather difcult. For a rough estimate the following approach has proven to be helpful.
b) Number of side lap screws: N2 = Roof or wall area respectively [m2] 2,2 + (building length [m] + builidng width [m]) 6
3,5 m
TRP 3 5/207 /0,75 mm
12
1,5 m
Estimated demand: N1 = 7 m 12 m 1,2 1,5 m 2 0,207 m = 162 self-drilling screws JT3-2-6,5x100-E16 + ORKAN storm washer
Acces sor ie s
For a rough estimate it can be assumed that an average of 4 screws per m at roof are needed.
Inst al l at i on to ol s
It is recommended to request a questionnaire that contains the most important information for the determination of the screw quantity.
FLAT ROOFING In particular for larger building projects the roong membrane and fastener manufacturers offer the service of initial sizing with determination of the needed volume. The result of this initial sizing idepends directly on the quality of the supplied data.
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
7m
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Service Information
S el f-dri l l i ng screw s
J T 3 -
FR
- 2 H - 4.8 x 19 - E 11 - 9006
Side lap screw EJOFAST Self-tapping screw coarse thread with point
F A Z B
S torm w a shers
Self-tapping screw ne pitch thread with dog point Self-tapping screw ne pitch thread with point Self-drilling screw material Case-hardened steel, zinc-plated
S peci a l screw s
2 3 4
R i vets
A2 stainless steel with hardened steel drill point A2 stainless steel Self-tapping screw material
Edelstahl A5 (1.4529) / Corremaks Zinc-plated steel A2 stainless steel A2 stainless steel / CRONIMAKS Version Standard (hexagon) Truss head
1 2 3 7
FR T D X
TORX drive Distance Special head geometry Countersunk head with TORX
P ipe f lashings
ST STS ZT S
Countersunk ange head with TORX Flat head with TORX Countersunk head Pan head with TORX Fibre cement max. drillable metal thickness (in mm) Free spin zone under screw head Screw diameter (in mm) Screw length (in mm) Sealing washer material Zinc-plated steel A2 stainless steel Aluminium Sealing washer diameter (in mm) Colour (4-digit RAL number)
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
LT FZ
V E A
RAL
Inst al l at i on to ol s
10
Acces sor ie s
SCREW TYPE
VERSION
TORX is a registered trademark of Acument Intellectual Properties, LLC, Troy Mich., US.
11
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Distance (D)
P ipe f lashings
R i vets
S peci a l screw s
Self-drilling screw JT
S torm w a shers
Service Information
S el f-dri l l i ng screw s
Screw type JT2-2-4,2 JT2-2H-4,8 JT2-3-4,8 JT2-3H-5,5 JT2-3-5,5 JT2-6-5,5 JT2-8-5,5 JT2-12-5,5 JT2-6-6,3 JT2-12-6,3
S peci a l screw s
Screwdriver rotation speed rpm 1800 1800 1800 1500 1500 1500 1500 1500 1500 1500
S torm w a shers
Drilling capacity tI + tII max tII min tII recommended application range tI + tII
Fa steni ng S yst . for S ol a r Inst a l l a ti ons R i vets
10
20
30
40
50
60
70
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Screwdriver rotation speed rpm 1800 1800 1500 1500 1300 1300 1300 12.0 mm
1.0
(Aer at ed) co ncr ete s cr ews
2.0
Inst al l at i on to ol s
20
12
Acces sor ie s
70
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0 mm
to slight
to tight
sloping
13
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
correct
P ipe f lashings
20
30
40
50
60
70
80 mm
R i vets
S torm w a shers
Screwdriver rotation speed rpm 1800 1800 1800 1500 1500 1500
Service Information
S el f-dri l l i ng screw s
GENERAL BUILDING AUTHORITIES APPROVAL Fasteners for structures with "cold proles" made of sheet steel - in particular proled steel panels Mechanical fasteners for xing aluminium components together, or with aluminium, steel, timber substructures Fasteners for sandwich element structures Self-drilling screws for xing aluminium clips for building authorities approved standing seam sheets, linear timber components with a min. thickness of 40 mm and other metal part to substructures made of steel, aluminium or wood-based materials Solar Fastening System for xing solar installations Composite anchor systems for embedment in masonry EJOT facade anchor SDF with accompanying special screws for xing faade fascia EJOT aerated concrete anchor SDP with accompanying special screws for xing faade fascia MKT anchor bolt B for embedment in cracked concrete and light ceiling cladding and suspended ceilings KERI conical anchor Special anchor made of stainless steel for the fastening of additional in a permanent manner of external weather resistant skins of three-layer external wall panels made of concrete EJOT VSD cavity wall repair anchor for subsequent installation of outer leafs Fibre cement corrugated prole 177/51 P5 and P6 with polypropylene strip insert (Eternit)
Z-14.1-4
S el f-ta ppi ng screw s
Z-14.1-537 Z-14.4-407
S torm w a shers
S peci a l screw s
Algemeine bauaufsichtliche Zulassungen ('national technical approvals') are granted for such construction products and types of construction for which there are no generally acknowledged rules of technology, DIN standards in particular, or which deviate considerably from these. National technical approvals are granted by the Deutsche Institut fr Bautechnik (DIBt) for all federal states. They are reliable verications of applicability of construction products and verications of applicability of types of construction relating to requirements of construction works in the eld of construction engineering.
Z-14.4-426
R i vets
Z-21.8-1265
D ir ect Fast ening
Z-21.2-1652 Z-31.1-144
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
GENERAL BUILDING AUTHORITIES APPROVALS Self-drilling screws for xing aluminium wall brackets to aluminium bearing prole substructures for rear-ventilated facade cladding Self-drilling screws for xing wooden slats to aluminium bearing prole substructures for rear-ventilated facade cladding Fixing aluminium structures to rear-ventilated facade cladding Fixing aluminium trapezoidal proles to aluminium substructures Self-drilling screws for xing wooden slats to aluminium bearing prole substructures for regulated rear-ventilated facade cladding according to DIN 18516-1 Self-drilling screws for xing aluminium wall brackets to aluminium bearing prole substructures for rear-ventilated facade cladding Self-drilling screws for xing aluminium wall brackets to aluminium bearing prole substructures for rear-ventilated facade cladding
14
Acces sor ie s
Inst al l at i on to ol s
Service Information
EUROPEAN TECHNICAL APPROVAL ETA-07/0013 ETA-06/0067 ETA-06/0068 ETA-06/0069 ETA-01/0013 ETA-05/0018 ETA-03/0017 ETA-99/0010 ETA-04/0069 ETA-99/0007 ETA-10/0200 ETA-10/0305 Fastening elements for roong membrane systems Composite anchor systems for embedment in masonry MKT anchor bolt B for embedment in cracked concrete and light ceiling cladding and suspended ceilings MKT anchor bolt BZ plus for embedment in cracked and non-cracked concrete EJOT special anchor WSS Special anchor made of stainless steel for the fastening of additional in a permanent manner of external weather resistant skins of three-layer external wall panels made of concrete Fasteners for metal components and sheet metal EJOT SDF-10V and SDF-10H plastic anchor for multiple fastening of non-loadbearing systems in concrete and masonry The European technical approval is a proof for the tness for use of a construction product within the meaning of the Construction Products Directive; transposed in Germany by the Bauproduktengesetz (Construction Products Law). The ETA is based on tests, examinations and a technical assessment by approval bodies designated by the EU Member States for this purpose. It covers all product characteristics which can be important for the fulllment of the legal requirements in the Member States, with the relevant levels of performance required being different in each Member State. A European technical approval can be granted for construction products for which harmonised specications according to the Construction Products Directive do not (yet) exist or which deviate substantially from a harmonized standard. Basis for the assessment of the tness for use are either Guidelines for European Technical Approvals ( ETAGs) prepared by EOTA for the relevant product area, or criteria for assessment procedures}that are agreed on with other EOTA bodies for issue of an approval of a specic request. In the interests of the manufacturer the verications presented to DIBt will be used as far as possible for the European procedure. The European technical approval enables the manufacturer to place the CE marking on the construction product and thus the access to the European market. With the CE marking the manufacturer conrms that he carried out the prescribed verication method and that the conformity of the product is given with the approval.
15
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
R i vets
S peci a l screw s
S torm w a shers
Self-drilling screw JT3-12-5,5xL-E16 page 62 + ORKAN storm washer Self-drilling screw JT3-12-5,5xL-E16 page 62 + ORKAN storm washer Self-drilling screw JT3-12-5,5x40-E22 page 62
Self-tapping screw JZ3-6,3xL-E16 page 80 + Storm washer pre-drilling 5,7 mm Self-tapping screw JZ3-6,3xL-E16 page 80 + Storm washer pre-drilling 5,7 mm Self-tapping screw JZ3-6,3x19-E22 page 80 pre-drilling 5,7 mm
Self-tapping screw JZ3-6,3xL-E16 page 80 + Storm washer Self-tapping screw JZ3-6,3xL-E16 page 80 + ORKAN storm washer Self-drilling screw JT3-6-5,5x25-E22 page 60
Self-tapping screw JA3-6,5xL-E16 page 78 + Storm washer pre-drilling 4,5 mm Self-tapping screw JA3-6,5xL-E16 page 78 + Storm washer pre-drilling 4,5 mm Self-tapping screw JA3-6,5x50-E22 page 78 pre-drilling 4,5 mm Self-drilling screw JT2-FZ-F-6,5 page 51
Self-drilling screw JT3-2-6,5xL-E16 page 58 + ORKAN storm washer Self-drilling screw JT3-2-6,5xL-E16 page 58 + ORKAN storm washer Self-drilling screw JT3-2-6,5x50-E22 page 58
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Acces sor ie s
Inst al l at i on to ol s
For highly corrosive environments we recommend the use of Corremaks self-tapping screws ............... page 82
16
h [mm]
L [mm]
180 200
Trapezoidal prole
Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm
Corrugated prole
Pre-drilling may be omitted if a self-drilling screw is used. Pre-drilling of timber has the advantage that expansion forces, which can lead to splicing of the wood, can be clearly reduced and for that reason a reduction of the edge distance is made possible through pre-drilling.
17
Acces sor ie s
SIDE LAP STITCHING If side lap stitching is not regulated any differently, it has to be spaced 50 - 666 mm apart, according to DIN 18807-3. A screw spacing of 500 mm has proven to be very practical. In order to prevent stripping of the proled sheets and destruction of the sealing washers the use of screws with a free spin zone is recommended.
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
For trapezoidal prole joints the installation depth into timber is regulated by the respective approval. The minimum installation depth of a 6,5 screw is 26 mm and the maximum installation depth is 78 mm. In practical experience an installation depth of 50 mm into timber has proven to be optimal, since the pullover load of a 0,75 mm thick steel trapezoidal prole shows approximately the same load bearing capacity against pulling-out of a timber purlin with 50mm installation depth as a 6,5 screw.
P ipe f lashings
DETERMINATION OF THE SCREW LENGTH Special attention should be paid to the waterproong of fastening elements. Practical experience has proven that leakage of only a few tenth millimetres can lead to considerable damage. For that reason EJOT recommends crown xing with storm washers. The advantage of a storm washer is safety against rain water penetration in addition to the effect that indentation of the crown can be largely prevented.
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Trapezoidal prole
Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Corrugated prole
18
Acces sor ie s
Inst al l at i on to ol s
Dolce Hotel
Service Notes
19
Acces sor ie s
Inst al l at i on to ol s
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Load-bearing shell to substructure Steel purlin 1,5 mm Steel purlin 6,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
Fastening to valley
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Inst al l at i on to ol s
Load-bearing shell
20
Acces sor ie s
page 60
DETERMINATION OF THE SCREW LENGTH h = Height of the trapezoidal or corrugated prole L = Screw length Proled sheet to steel substructure 1,5 5,0 mm JT3-6-5,5xL-E16 + ORKAN storm washer h [mm] 18 44 38 64 L [mm] 70 90 110 130 150 170 190
Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm
21
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Load-bearing shell to substructure Steel purlin 1,5 mm Steel purlin 6,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
Fastening to valley
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Inst al l at i on to ol s
Load-bearing shell
22
Acces sor ie s
Substructure (component II) Clip on substructure Spacer 1,5 mm Spacer 1,5 5,0 mm Trapezoidal prole 0,75 mm Roof boarding / OSB
Position 2
Ancho rs and Embe dmen t Tec hnol og y
23
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
DETERMINATION OF THE SCREW LENGTH h = Clip height incl, Thermo stop L = screw length
NOTE The JT3-X-2-6,0xL self-drilling screw is a building authorities approved product to fasten clips to steel, timber or aluminium substructures. Every clip has to be xed with 2 screws in the order depicted below. The special characteristic of the screw are the grooves under the head. They are able to considerably increase the stripping torque, which leads to an increased assembly reliability.
R i vets
S peci a l screw s
S torm w a shers
S peci a l screw s
S torm w a shers
R i vets
Substructure (component II) Sandwich element to substructure Steel purlin 1,5 5,0 mm Steel purlin 4,0 12,0 mm Steel purlin 10,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
Fastening to crown
24
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Proled sheet to timber substructure Min. width 65 mm JT3-2-6,5xL-E16 + ORKAN storm washer h [mm] L [mm]
180 200
Trapezoidal prole
Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm
Corrugated prole
25
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Load-bearing shell to substructure Steel purlin 1,5 mm Steel purlin 6,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
Fastening to valley
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
NOTE Compared to the metal-metal combination, the metal plastic combination has the advantage of minimal thermal transmittance and the telescope effect prevents screw head protrusion due to foot trafc. Metall-metal combinations are indispensable for renovations where old bitumen roong membranes are equipped with a new layer of insulation material. A plastic stress plate can only be installed with increased assembly effort in these kind of applications. For renovations we generally recommend A4 stainless steel screws, since increased corrosion can be expected for wet roof structures. CLIMADUR High-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
Inst al l at i on to ol s
Load-bearing shell
26
Acces sor ie s
20 mm Dabo screw A/F 8-R-4,8xL page 128 + stress plate HTV 82/40 F page 135
30 mm Dabo screw A/F 8-R-4,8xL page 128 + stress plate HTV 82/40 F page 135
30 50 mm Concrete screw FBS-R-6,3xL page 139 + stress plate HTV 82/40 F page 135
60 mm Aerated concrete screw FPS-E-8,0xL page 140 + stress plate HTV 82/40 F page 135
Trapezoidal prole
Concrete
Porous concrete
20 mm Dabo screw A/F 8-RT-4,8xL page 129 + stress plate HTV 82/40 page 134 Dabo screw TKR-4,8xL page 130 + stress plate HTK 50xL page 136
30 mm Dabo screw A/F 8-RT-4,8xL page 129 + stress plate HTV 82/40 page 134 Dabo screw TKR-4,8xL page 130 + stress plate HTK 50xL page 136
30 35 mm
60 mm
27
Acces sor ie s
Inst al l at i on to ol s
Metal-plastic combination
Concrete screw FBS-R-6,3xL page 139 + stress plate EcoTek 50xL page 136
Aerated concrete screw FPS-E-8,0xL page 140 + stress plate EcoTek 50xL page 136
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Trapezoidal prole Roof boarding / OSB Concrete Porous concrete
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Proled sheet to substructure Steel purlin 1,5 5,0 mm Steel purlin 4,0 12,0 mm Steel purlin 10,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
28
Acces sor ie s
Inst al l at i on to ol s
page 55
Self-drilling screw JT3-2H-Plus-5,5x25-E11 Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm Self-drilling screw JT3-FR-2H-Plus-5,5x25-E11
Page 55 page 56
29
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Cassette to substructure Steel purlin 4,0 12 mm Steel purlin 6,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
P ipe f lashings
Fixing to valley
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
NOTE The fastening elements may only be mounted a max. of 75 m away from the cassette bars The fastener in the middle of the cassette does not serve the load-transmission but it has only a structural character. Depending on the cassette type and manufacturer it is not easy to adhere to the 75 mm during the installation and at the same time install the the fastening element perpendicular to the surface. The closer the vertical seam is positioned to the valley the more effective condensation can be prevented. The corrugation bridges are not a positioning aid for the side lap stitching of cassettes.
Inst al l at i on to ol s
30
Acces sor ie s
page 56
page 61
Trapezoidal prole
Side lap screw JF3-2H-4,8x19-E14 page 53 Drilling capacity tI + tII (0,88 + 0,88) mm
Corrugated prole
page 55
page 56
31
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Substructure (component II) Sandwich element to substructure Steel purlin 1,5 5,0 mm Steel purlin 4,0 12,0 mm Steel purlin 10,0 mm Insertion rail 3,0 mm Timber purlin Min. width 65 mm
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
32
Acces sor ie s
Inst al l at i on to ol s
Sandwich element to timber substructure Min. width 65 mm JT3-2-6,5xL-E19 h [mm] 20 40 40 60 60 80 80 100 100 120 120 - 140 L [mm] 100 120 140 160 180
NOTE Practical experience has shown that visibly installed sandwich panels always show a slight indentation at the fastening point. When using screws with high thread (JT3-D) indentations can be reduced but not completely prevented.
33
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
200
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
P ipe f lashings
EJOT is a member of the "Fachverband Baustoffe und Bauteile fr vorgehngte hinterlftete Fassaden e.V." (professional association building material and components for rear ventilated facade)
Embedment substrate Concrete Solid brick Hollow or perforated brick Porous concrete
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Timber substructure
Metal substructure
Inst al l at i on to ol s
34
Acces sor ie s
Aluminium / aluminium
The application area of this screw is limited to a 3,0 mm thick wall bracket and a 1,6 mm to 2,0 mm thick bearing prole.
Timber / aluminium
page 163 page 164 + metal insulation stress plate DMT Hard insulating material Metal insulation support anchor DMH page 164 Wood cladding
page 73
page 98
35
Acces sor ie s
Inst al l at i on to ol s
Plaster-base sheeting
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
S torm w a shers
36
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Service Notes
WALE INDOOR PLAYGROUND, FRIEDRICHSKOOG, GERMANY Supplied by EJOT: EJOT Dabo screw A/F8
Self-drilling screws
PRODUCT VERSIONS EJOT Self-drilling screws SAPHIR JT2 SUPER-SAPHIR JT3 Stainless steel SAPHIR JT4
steel 12
steel or aluminium 12
aluminium 6
PRODUCT VERSIONS EJOT Self-drilling screws EJOFAST Side lap screw JF2 EJOFAST Side lap screw JF3
A2 stainless steel with hardened drill point steel or aluminium 0.88 + 0.88
tII
tI
Clamp thickness
37
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
Fastener Material
A2 stainless steel
S torm w a shers
S el f-dri l l i ng screw s
S torm w a shers
APPLICATION RANGE Side lap stitching of profiled steel sheets FEATURES Case-hardened steel, zinc-plated APPROVAL ETA-10/0200
mm
Length mm
PU
Part number
1,000
3591100624
S peci a l screw s
TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 1,0 mm Drive ........................................................... hexagont A/F7 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
R i vets
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Side lap stitching of proled steel sheets FEATURES Steel, case-hardened, zinc-plated with innovative screw point geometry With free spin zone under the screw head for side lap stitching Non-skid application Fastening without swarf APPROVAL ETA pending TECHNICAL DATA Drilling capacity tI + tII ............................... 0,88 + 0,88 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
in mm
Length mm
Clamp thickness in mm
PU
Part Number
0 - 9 1,000
7380628601
38
Acces sor ie s
Inst al l at i on to ol s
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-2H-4,8
J2
S el f-dri l l i ng screw s
APPLICATION RANGE Side lap stitching of profiled steel sheets FEATURES Case-hardened steel, zinc-plated With free spin zone under the screw head for side lap stitching APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
PU
Part number
1,000
3592200644
39
Acces sor ie s
Inst al l at i on to ol s
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................................ hexagon A/F8
Clamp Price / thickness PU Order description Part number 100 pcs. mm Sealing washer V14, 14 mm 4.8 20 0 - 6 1,000 JT2-2H/3-4,8x20-V14 3592251644 RAL 9006 RAL 9002 RAL 8012 RAL 7016 RAL 6020 RAL 5010 Sealing washer V14, 14 mm, coloured white aluminium grey white red brown anthracite chrome oxide green gentian blue 4.8 20 0 - 6 1,000 JT2-2H/3-4,8x20-V14* * add four-digit RAL colour code. mm Length mm
FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer With free spin zone under the screw head for side lap stitching APPROVAL ETA-10/0200
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE Fastening of profiled steel sheets onto timber substructure Fastening of roofing sheets onto timber substructure FEATURES Case-hardened steel, zinc-plated, powder-coated Steel sealing washer, zinc-plated Pre-assembled sealing washer Thread according to DIN 7998 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
S peci a l screw s
S torm w a shers
mm
Length mm
PU
Part number
R i vets
Sealing washer V14, 14 mm, coloured 4.9 35 500 * add four-digit RAL colour code.
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Side lap stitching of profiled steel sheets Fastening of proled steel sheets onto 0.63 1.5 mm steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer With free spin zone under the screw head for side lap stitching APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Part number
without sealing washer (no approval) 5.5 22 0 - 10 1,000 Sealing washer V16, 16 mm 5.5 22 0-7 500
3593300644 3593321644
40
Acces sor ie s
Inst al l at i on to ol s
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-2H-6,3
J2
S el f-dri l l i ng screw s
APPLICATION RANGE Side lap stitching of proled steel sheets FEATURES Case-hardened steel, zinc-plated With free spin zone under the screw head for side lap stitching TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
PU
Part number
500 500
7380188601 7380452601
TECHNICAL DATA Drilling capacity tI + tII ............................................ 2,0 mm Drive ........................................................hexagon A/F3/8 mm Length mm 35 50 65 90 35 50 65 90 PU Price / Order description 100 pcs. JT2-2-6,5x35 JT2-2-6,5x50 JT2-2-6,5x65 JT2-2-6,5x90 JT2-2-6,5x35-V16 JT2-2-6,5x50-V16 JT2-2-6,5x65-V16 JT2-2-6,5x90-V16 Part number CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
41
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 6.5 6.5 6.5 6.5 Sealing washer V16, 16 mm 6.5 6.5 6.5 6.5
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S torm w a shers
APPLICATION RANGE Fastening of profiled steel sheets onto 2 mm steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer APPROVAL ETA-10/0200
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JT2-3-4,8x19 JT2-3-4,8x25 JT2-3-4,8x38 JT2-3-4,8x19-V14 JT2-3-4,8x25-V14 JT2-3-4,8x38-V14
Part number
S peci a l screw s
TECHNICAL DATA Drilling capacity tI + tII ....................................1,5 + 2,5 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
without sealing washer (no approval) 4.8 19 0 - 11 4.8 25 0 - 17 4.8 38 0 - 27 Sealing washer V14, 14 mm 4.8 19 0-8 4.8 25 0 - 14 4.8 38 0 - 24
R i vets
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Fastening of proled steel sheets onto 1 2.5 mm steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,5 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Part number
42
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 5.5 19 0-6 5.5 25 0 - 12 Sealing washer V16, 16 mm 5.5 19 0-3 5.5 25 0-9
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-3H-5,5
J2
S el f-dri l l i ng screw s
mm
Length mm
Clamp thickness mm
PU
Part number
APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,5 + 1,5 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
J2
APPLICATION RANGE Side lap stitching of profiled steel sheets Fastening of profiled steel sheets onto 1 2,5 mm steel substrate mm Length mm Clamp thickness mm 0-9 0 - 19 PU Price / Order description 100 pcs. JT2-3H-6,3x22 JT2-3H-6,3x32 Part number FEATURES Case-hardened steel, zinc-plated With free spin zone under the screw head for side lap stitching TECHNICAL DATA Drilling capacity tI + tII ................................... 1,5 + 1,5 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
500 500
3574300654 3574500654
43
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
without sealing washer (no approval) 5.5 19 6 5.5 25 12 Sealing washer V16, 16 mm 5.5 19 3 5.5 25 9
FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer With free spin zone under screw head for side lap stitching
S peci a l screw s
S torm w a shers
APPLICATION RANGE Side lap stitching of proled steel sheets Fastening of proled steel sheets onto 1 2.5 mm steel substrate
S torm w a shers
APPLICATION RANGE Fastening of proled steel sheets onto 1,5 5 mm steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer APPROVAL ETA-10/0200 mm Length mm Clamp thickness mm Price / Order description 100 pcs. JT2-6-5,5x19 JT2-6-5,5x22 JT2-6-5,5x25 JT2-6-5,5x19-V16 JT2-6-5,5x22-V16 JT2-6-5,5x25-V16
PU
Part number
TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 5,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
without sealing washer 5.5 19 0-7 5.5 22 0 - 10 5.5 25 0 - 13 Sealing washer V16, 16 mm 5.5 19 0-4 5.5 22 0-7 5.5 25 0 - 10
S peci a l screw s
R i vets
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Fastening of profiled steel sheets onto 2 5 mm steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,5 + 5,0 mm Drive ........................................................hexagon A/F3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JT2-6-6,3x19 JT2-6-6,3x22 JT2-6-6,3x25 JT2-6-6,3x32 JT2-6-6,3x38 JT2-6-6,3x19-V16 JT2-6-6,3x22-V16 JT2-6-6,3x25-V16 JT2-6-6,3x32-V16 JT2-6-6,3x38-V16
Part number
44
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 6.3 19 0-7 6.3 22 0 - 10 6.3 25 0 - 13 6.3 32 0 - 20 6.3 38 0 - 26 Sealing washer V16, 16 mm 6.3 19 0-4 6.3 22 0-7 6.3 25 0 - 10 6.3 32 0 - 17 6.3 38 0 - 23
500 500 500 500 500 500 500 500 500 500
3574200634 3574300634 3574400634 3574500634 3574600634 3574221634 3574321634 3574421634 3574521634 3574621634
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-8-5,5
J2
S el f-dri l l i ng screw s
mm
Length mm
Clamp thickness mm
PU
Part number APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,5 + 8,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JT2-12-5,5x35 JT2-12-5,5x50 JT2-12-5,5x65 JT2-12-5,5x80 JT2-12-5,5x110 JT2-12-5,5x130 JT2-12-5,5x35-V16 JT2-12-5,5x50-V16 JT2-12-5,5x65-V16 JT2-12-5,5x80-V16 JT2-12-5,5x110-V16 JT2-12-5,5x130-V16
Part number
45
Acces sor ie s
without sealing washer (no approval) 5.5 35 0 - 13 5.5 50 0 - 28 5.5 65 9 - 43 5.5 80 24 - 58 5.5 110 54 - 88 5.5 130 74 - 108 Sealing washer V16, 16 mm 5.5 35 0 - 10 5.5 50 0 - 25 5.5 65 6 - 40 5.5 80 21 - 55 5.5 110 51 - 85 5.5 130 71 - 105
TECHNICAL DATA Drilling capacity tI + tII ......... 1,0 + 12,0 mm / 2,0 + 10,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
Inst al l at i on to ol s
APPROVAL ETA-10/0200
FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Steel sealing washer, zinc-plated Pre-assembled sealing washer
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
without sealing washer 5.5 25 0 - 12 5.5 35 0 - 22 Sealing washer V16, 16 mm 5.5 25 0-9 5.5 35 0 - 19
500 500
3573421694 3573621694
R i vets
500 500
3573400694 3573600694
S peci a l screw s
FEATURES Case-hardened steel, zinc-plated Sealing steel washer, zinc-plated Pre-assembled sealing washer
S torm w a shers
S torm w a shers
APPLICATION RANGE Fastening of proled steel sheets onto 4 10 mm steel substrate FEATURES Case-hardened steel, zinc-plated Sealing steel washer, zinc-plated Pre-assembled sealing washer TECHNICAL DATA Drilling capacity tI + tII ................................. 2,0 + 10,0 mm Drive .......................................................... hexagon A/F10 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180 mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT2-12-6,3x35 JT2-12-6,3x35-V16 Part number
S peci a l screw s
R i vets
500 250
3595600614 3595621614
46
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-D-6H-5,5/6,3
J2
S el f-dri l l i ng screw s
FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Sealing steel washer, zinc-plated or stainless steel Pre-assembled sealing washer With free spin zone under screw head High thread TECHNICAL DATA Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Self-tapping screw JZ7-6,3 ...................... page 83 Special screwgun DAM 5 .......................... page 180
mm
High thread mm
Length mm 62 82 102 122 152 172 192 62 82 102 122 152 172 192
For sandwich panels 32.0 - 44.0 42.0 - 64.0 62.0 - 84.0 82.0 - 104.0 102.0 - 134.0 132.0 - 154.0 152.0 - 174.0 32.0 - 44.0 42.0 - 64.0 62.0 - 84.0 82.0 - 104.0 102.0 - 134.0 132.0 - 154.0 152.0 - 174.0
PU
Price / Order description 100 pieces JT2-D-6H-5,5/6,3x62-E19 JT2-D-6H-5,5/6,3x82-E19 JT2-D-6H-5,5/6,3x102-E19 JT2-D-6H-5,5/6,3x122-E19 JT2-D-6H-5,5/6,3x152-E19 JT2-D-6H-5,5/6,3x172-E19 JT2-D-6H-5,5/6,3x192-E19 JT2-D-6H-5,5/6,3x62-V16 JT2-D-6H-5,5/6,3x82-V16 JT2-D-6H-5,5/6,3x102-V16 JT2-D-6H-5,5/6,3x122-V16 JT2-D-6H-5,5/6,3x152-V16 JT2-D-6H-5,5/6,3x172-V16 JT2-D-6H-5,5/6,3x192-V16
Part number
47
Acces sor ie s
Inst al l at i on to ol s
Sealing washer E19, 19 mm 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 Sealing washer V16, 16 mm 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3
250 200 200 150 100 100 100 250 200 200 150 150 150 100
3553412674 3553612674 3553812674 3557012674 3555912674 3556412674 3556612674 3553421674 3553621674 3553821674 3557021674 3555921674 3556421674 3556621674
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S torm w a shers
APPLICATION RANGE Fastening sandwich elements onto 3-12 mm steel substructures FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Sealing steel washer, zinc-plated or stainless steel Pre-assembled sealing washer With free spin zone under screw head High thread TECHNICAL DATA Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Self-tapping screw JZ7-6,3 ...................... page 83 Special screwgun DAM5 .......................... page 180
P ipe f lashings
R i vets
S peci a l screw s
mm
High thread mm
Length mm 80 95 115 135 155 195 235 250 275 300 80 95 115 135 155 195 235 250 275 300
For sandwich panels 41.0 - 50.0 46.0 - 65.0 60.0 - 85.0 75.0 - 105.0 90.0 - 125.0 120.0 - 165.0 160.0 - 205.0 175.0 - 220.0 200.0 - 245.0 225.0 - 270.0 41.0 - 50.0 46.0 - 65.0 60.0 - 85.0 75.0 - 105.0 90.0 - 125.0 120.0 - 165.0 160.0 - 205.0 175.0 - 220.0 200.0 - 245.0 225.0 - 270.0
PU
Price / Order description 100 pieces JT2-D-12H-5,5/6,3x80-E19 JT2-D-12H-5,5/6,3x95-E19 JT2-D-12H-5,5/6,3x115-E19 JT2-D-12H-5,5/6,3x135-E19 JT2-D-12H-5,5/6,3x155-E19 JT2-D-12H-5,5/6,3x195-E19 JT2-D-12H-5,5/6,3x235-E19 JT2-D-12H-5,5/6,3x250-E19 JT2-D-12H-5,5/6,3x275-E19 JT2-D-12H-5,5/6,3x300-E19 JT2-D-12H-5,5/6,3x80-V16 JT2-D-12H-5,5/6,3x95-V16 JT2-D-12H-5,5/6,3x115-V16 JT2-D-12H-5,5/6,3x135-V16 JT2-D-12H-5,5/6,3x155-V16 JT2-D-12H-5,5/6,3x195-V16 JT2-D-12H-5,5/6,3x235-V16 JT2-D-12H-5,5/6,3x250-V16 JT2-D-12H-5,5/6,3x275-V16 JT2-D-12H-5,5/6,3x300-V16
Part number
Sealing washer E19, 19 mm 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 Sealing washer V16, 16 mm 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3 5.5 6.3
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
200 200 150 150 100 100 100 150 100 100 200 200 200 150 150 150 150 100 100 100
3554712614 3554912614 3555212614 3555412614 3555712614 3559512614 3557112614 3557212614 3557312614 3557412614 3554721614 3554921614 3555221614 3555421614 3555721614 3559521614 3557121614 3557221614 3557321614 3557421614
48
Acces sor ie s
Inst al l at i on to ol s
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-FZ-6-6,3
J2
S el f-dri l l i ng screw s
FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Pre-assembled FZD sealing washer A2 stainless steel washer Clearing wings save additional drilling into the corrugated panel no forcing tension TECHNICAL DATA Drive ............................................................ hexagon A/F8 NOTE For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
mm
Length mm
PU
Part number
CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
49
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
6.3 110 100 6.3 150 50 Order information: Further lengths on request
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE Fastening 177/51 sandwich elements onto 1.5-6 mm steel substructures
S torm w a shers
APPLICATION RANGE Fastening 177/51 sandwich elements onto 5-12 mm steel substructures FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Pre-assembled FZD sealing washer A2 stainless steel washer Clearing wings save additional drilling into the corrugated panel no forcing tension TECHNICAL DATA Drive ............................................................ hexagon A/F8 NOTE For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
R i vets
S peci a l screw s
CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm 6.3
Length mm 115
PU 100
50
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
JT2 self-drilling screws Case-hardened steel EJOT SAPHIR Self-drilling screw JT2-FZ-F-6,5
J2
S el f-dri l l i ng screw s
FEATURES Case-hardened steel, hot-dip zinc-plated Pre-assembled FZD sealing washer A2 stainless steel washer Clearing wings save additional drilling into the corrugated panel no forcing tension APPROVAL Z-31.1-144 (Eternit) TECHNICAL DATA Drive ............................................................ hexagon A/F8 Part number NOTE Suitable for corrugation 5 when covering with brous cement corrugated sheets 177/51 onto timber substructure without insulation. For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals. CROSS REFERENCE Accessories ............................................ page 191 JT4-FZ-6,5 ............................................. page 72 Special screwgun DAM5 .......................... page 180
PU 100 100 50
APPROVAL Z-14.4-426 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
51
Acces sor ie s
Inst al l at i on to ol s
mm
Length mm
Clamp thickness mm
PU
Part number
FEATURES Case-hardened steel Climadur coated high-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPLICATION RANGE Fastening wooden parts onto thin-walled steel / aluminium substrate
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE Fastening of brous cement corrugated sheets onto timber substructure
52
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P. Lange
DUBAI METRO, DUBAI Supplied by EJOT: EJOT stainless steel SAPHIR self-drilling screw JT4, EJOT SAPHIR self-drilling screw JT2
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOFAST Side lap screw JF3-2H-4,8
J3
S el f-dri l l i ng screw s
Clamp thickness in mm Sealing washer E 14, 14 mm 4.8 19 0-4 Sealing washer E 16, 16 mm 4.8 19 0-4 in mm Length mm
PU
Part Number
500 500
3591977391 3591911391
TECHNICAL DATA Drilling capacity tI + tII ............................... 0,88 + 0,88 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
APPLICATION RANGE Side lap stitching of proled steel sheets Side lap stitching of proled aluminium sheets mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT3-2H-4,8x19-E14 JT3-2H-4,8x19-E16 Part number FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
Sealing washer E14, 14 mm 4.8 19 0-4 Sealing washer E16, 16 mm 4.8 19 0-4
500
3591911351
53
Acces sor ie s
Inst al l at i on to ol s
1,000
3591977351
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPROVAL ETA-10/0200
R i vets
FEATURES A2 stainless steel with innovative point geometry Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching Non-skid application Fastening without swarf
S peci a l screw s
S torm w a shers
APPLICATION RANGE Side lap stitching of proled steel sheets Side lap stitching of proled aluminium sheets
S torm w a shers
APPLICATION RANGE Side lap stitching of corrugated profile steel sheets Side lap stitching of corrugated prole aluminium sheets FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 1,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Part number
1,000
3591968358
R i vets
S peci a l screw s
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For fixing profiled steel sheets to timber substructure For fixing aluminium profiled sheets to timber substructure For fixing roofing sheets to timber substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer Thread according to DIN 7998 APPROVAL Z-14.1-537 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm 35 35 70
PU
Part number
54
Acces sor ie s
Inst al l at i on to ol s
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-FR-2-4,9
with truss head
S el f-dri l l i ng screw s
mm
Length mm
PU
Part number
APPLICATION RANGE For fixing corrugated prole steel sheets to timber substructure For xing corrugated prole aluminium sheets to timber substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer Thread according to DIN 7998 APPROVAL Z-14.1-537 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
500
3593568328
J3
mm
500 -
CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
55
Acces sor ie s
TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,5 mm Drive ......................................................................... A/F8
Inst al l at i on to ol s
Clamp thickness mm Sealing washer E16, 16 mm 5.5 25 0 - 10 5.5 30 0 - 15 5.5 35 0 - 20 Sealing washer E22, 22 mm 5.5 25 0 - 10 5.5 30 0 - 15 5.5 35 0 - 20 Length mm
PU
Part number
APPLICATION RANGE Side lap stitching of proled steel sheets Side lap stitching of proled aluminium sheets For xing proled steel sheets to cassette system walls For xing proled aluminium sheets to cassette system walls FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching
500 500 -
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE Side lap stitching of proled steel sheets Side lap stitching of proled aluminium sheets For xing proled steel sheets to cassette system walls For xing proled aluminium sheets to cassette system walls FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching APPROVAL Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,5 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
S torm w a shers
PU
Part number
S peci a l screw s
1,000
3592269398
56
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-2-5,6
J3
S el f-dri l l i ng screw s
APPLICATION RANGE For xing proled steel sheets to timber substructure For xing aluminium proled sheets to timber substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drilling capacity tI + tII.............................................2,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
PU
Part number
35
500
54.80
JT3-2-5,6x35-E22
3594513321
J3
APPLICATION RANGE For fixing proled sheets with/without intermediate insulation to thin-walled steel / aluminium substructure as well as timber substructure mm Length mm Clamp thickness mm Price / Order description 100 pcs. JT3-2-6x25-E16 JT3-2-6x120-E16 JT3-2-6x140-E16 JT3-2-6x160-E16 JT3-2-6x25-E22 JT3-2-6x120-E22 JT3-2-6x140-E22 JT3-2-6x160-E22 APPROVAL Z-14.4-426 Z-14.1-537 FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
PU
Part number
57
Acces sor ie s
Inst al l at i on to ol s
Sealing washer E16, 16 mm 6.0 25 0-7 6.0 120 53 - 103 6.0 140 73 - 123 6.0 160 93 - 143 Sealing washer E22, 22 mm 6.0 25 0-7 6.0 120 53 - 103 6.0 140 73 - 123 6.0 160 93 - 143
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
35
500
50.10
JT3-2-5,6x35-E16
3594511321
S peci a l screw s
mm
Length mm
S torm w a shers
APPLICATION RANGE For xing proled steel sheets to timber substructure For xing proled aluminium sheets to timber substructure For xing sandwich panels to timber substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.4-407 Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ............................................ 2,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ Storm washers ........................................ Self-tapping screw JA3-6,5 ...................... Special screwgun DAM5 .......................... Special screwgun DAM5-SH2 ...................
S peci a l screw s
S torm w a shers
R i vets
mm
Length mm
PU
Price / Order description 100 pcs. JT3-2-6,5x50-E16 JT3-2-6,5x65-E16 JT3-2-6,5x80-E16 JT3-2-6,5x100-E16 JT3-2-6,5x120-E16 JT3-2-6,5x140-E16 JT3-2-6,5x160-E16 JT3-2-6,5x180-E16 JT3-2-6,5x200-E16 JT3-2-6,5x220-E16 JT3-2-6,5x240-E16 JT3-2-6,5x50-E22 JT3-2-6,5x65-E22 JT3-2-6,5x80-E22 JT3-2-6,5x100-E22 JT3-2-6,5x120-E22 JT3-2-6,5x140-E22 JT3-2-6,5x160-E22 JT3-2-6,5x180-E22 JT3-2-6,5x200-E22 JT3-2-6,5x220-E22 JT3-2-6,5x240-E22
Part number
58
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Sealing washer E16, 16 mm 6.5 50 6.5 65 6.5 80 6.5 100 20 - 40 6.5 120 40 - 60 6.5 140 60 - 80 6.5 160 80 - 100 6.5 180 100 - 120 6.5 200 120 - 140 6.5 220 140 - 160 6.5 240 160 - 180 Sealing washer E22, 22 mm 6.5 50 6.5 65 6.5 80 6.5 100 20 - 40 6.5 120 40 - 60 6.5 140 60 - 80 6.5 160 80 - 100 6.5 180 100 - 120 6.5 200 120 - 140 6.5 220 140 - 160 6.5 240 160 - 180
250 250 200 200 150 150 150 100 100 100 100 250 250 150 150 100 100 100 100 100 100 50
3598811321 3598911321 3598011321 3598111321 3598311321 3598511321 3598711321 3598211321 3599011321 3599111321 3599211321 3598813321 3598913321 3598013321 3598113321 3598313321 3598513321 3598713321 3598213321 3599013321 3599113321 3599213321
P ipe f lashings
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-3-5,5
J3
S el f-dri l l i ng screw s
APPLICATION RANGE For fixing proled steel sheets to 1 2,5 mm steel substructure For xing proled aluminium sheets to 1 2,5 mm aluminium or steel substructure mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT3-3-5,5x25-E16 JT3-3-5,5x35-E16 JT3-3-5,5x50-E16 JT3-3-5,5x70-E16 Part number FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,5 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Self-drilling screw JT3-2H-Plus-5,5 .......... page 55 Special screwgun DAM5 .......................... page 180
APPLICATION RANGE For fixing corrugated prole steel sheets to 1 2,5 mm steel substructure For xing corrugated prole aluminium sheets to 1 2,5 mm aluminium or steel substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,5 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
500
JT3-FR-3-5,5x50-E11
3592869335
59
Acces sor ie s
Inst al l at i on to ol s
mm
Length mm
Clamp thickness mm
PU
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For fixing proled steel sheets to 1.5 5 mm steel substructure For xing proled aluminium sheets / sandwich panels to 1,5 5 mm aluminium or steel substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.4-407 Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 5,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ Storm washers ........................................ Self-tapping screw JZ3-6,3 ...................... Special screwgun DAM5 .......................... Special screwgun DAM5-SH2 ....................
S torm w a shers
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JT3-6-5,5x25-E16 JT3-6-5,5x30-E16 JT3-6-5,5x35-E16 JT3-6-5,5x50-E16 JT3-6-5,5x70-E16 JT3-6-5,5x90-E16 JT3-6-5,5x110-E16 JT3-6-5,5x130-E16 JT3-6-5,5x150-E16 JT3-6-5,5x170-E16 JT3-6-5,5x190-E16 JT3-6-5,5x25-E22 JT3-6-5,5x30-E22 JT3-6-5,5x35-E22 JT3-6-5,5x50-E22 JT3-6-5,5x70-E22 JT3-6-5,5x90-E22 JT3-6-5,5x110-E22 JT3-6-5,5x130-E22 JT3-6-5,5x150-E22 JT3-6-5,5x170-E22 JT3-6-5,5x190-E22
Part number
60
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Sealing washer E16, 16 mm 5.5 25 0-7 5.5 30 0 - 11 5.5 35 0 - 16 5.5 50 0 - 31 5.5 70 20 - 51 5.5 90 40 - 71 5.5 110 60 - 91 5.5 130 80 - 111 5.5 150 100 - 131 5.5 170 120 - 151 5.5 190 140 - 171 Sealing washer E22, 22 mm 5.5 25 0-7 5.5 30 0 - 11 5.5 35 0 - 16 5.5 50 0 - 31 5.5 70 20 - 51 5.5 90 40 - 71 5.5 110 60 - 91 5.5 130 80 - 111 5.5 150 100 - 131 5.5 170 120 - 151 5.5 190 140 - 171
S peci a l screw s
500 500 500 250 250 200 200 200 150 150 100 500 500 500 250 200 150 150 100 100 100 100
3572211361 3572311361 3572511361 3592811361 3593911361 3596111361 3596211361 3596311361 3596411361 3596511361 3596611361 3572213361 3572313361 3572513361 3592813361 3593913361 3596113361 3596213361 3596313361 3596413361 3596513361 3596613361
R i vets
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-FR-6-5,5
with truss head
S el f-dri l l i ng screw s
APPLICATION RANGE For fixing corrugated prole steel sheets to 1.5 5 mm steel substructure For xing corrugated prole aluminium sheets to 1,5 5 mm aluminium or steel substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 5,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Part number
500
3592569368
J3
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For fixing proled steel sheets to 1.5 5 mm steel substructure For xing proled aluminium sheets to 1,5 5 mm aluminium or steel substructure mm Length mm Clamp thickness mm 7 7 Price / Order description 100 pcs. JT3-6-6,3x25-E16 JT3-6-6,3x25-E22
PU
Part number
500
3599413361
APPROVAL ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 5,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
61
Acces sor ie s
Inst al l at i on to ol s
500
3599411361
FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer
P ipe f lashings
1,000
3592269368
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For fixing proled steel sheets to 4 10 mm steel substructure For xing proled aluminium sheets / sandwich panels to 4-10 mm steel substructure For xing proled aluminium sheets / sandwich panels to 4 12 mm aluminium substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer APPROVAL Z-14.4-407 Z-14.1-537 ETA-10/0200 TECHNICAL DATA Drilling capacity tI + tII 2,0 + 10,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ Storm washers ........................................ Self-tapping screw JZ3-6,3 ...................... Special screwgun DAM5 .......................... Special screwgun DAM5-SH2 ...................
S torm w a shers
S peci a l screw s
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JT3-12-5,5x40-E16 JT3-12-5,5x58-E16 JT3-12-5,5x78-E16 JT3-12-5,5x98-E16 JT3-12-5,5x118-E16 JT3-12-5,5x138-E16 JT3-12-5,5x158-E16 JT3-12-5,5x178-E16 JT3-12-5,5x198-E16 JT3-12-5,5x40-E22 JT3-12-5,5x58-E22 JT3-12-5,5x78-E22 JT3-12-5,5x98-E22 JT3-12-5,5x118-E22 JT3-12-5,5x138-E22 JT3-12-5,5x158-E22 JT3-12-5,5x178-E22 JT3-12-5,5x198-E22
Part number
62
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Sealing washer E16, 16 mm 5.5 40 0 - 11 5.5 58 0 - 31 5.5 78 20 - 51 5.5 98 40 - 71 5.5 118 60 - 91 5.5 138 80 - 111 5.5 158 100 - 131 5.5 178 120 - 151 5.5 198 140 - 171 Sealing washer E22, 22 mm 5.5 40 0 - 11 5.5 58 0 - 31 5.5 78 20 - 51 5.5 98 40 - 71 5.5 118 60 - 91 5.5 138 80 - 111 5.5 158 100 - 131 5.5 178 120 - 151 140 - 171 5.5 198
500 500 250 250 150 150 150 150 100 250 500 200 150 150 100 100 100 100
3595611311 3595811311 3595011311 3595111311 3595211311 3595311311 3595411311 3595511311 3595711311 3595613311 3595813311 3595013311 3595113311 3595213311 3595313311 3595413311 3595513311 3595713311
R i vets
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-FR-12-5,5
with truss head
S el f-dri l l i ng screw s
mm
Length mm
Clamp thickness mm
PU
Part number
500
3595669318
63
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
TECHNICAL DATA Drilling capacity tI + tII ................................. 2,0 + 10,0 mm Drive ............................................ Hexalobular / TORX T25
R i vets
FEATURES A2 stainless steel, with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer
S peci a l screw s
APPLICATION RANGE For fixing corrugated prole steel sheets to 4 10 mm steel substructure For xing corrugated prole aluminium sheets to 4 10 mm steel substructure For xing corrugated prole aluminium sheets to 4 12 mm aluminium substructure
S torm w a shers
S torm w a shers
APPLICATION RANGE For fixing sandwich panels to 1,5 5 mm steel substructure FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head High thread APPROVAL Z-14.4-407 TECHNICAL DATA Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-6-5,5 .................... Self-tapping screw JZ3-6,3 ...................... Self-tapping screw JZ7-6,3 ...................... Special screwgun DAM5 ..........................
R i vets
S peci a l screw s
mm
high thread mm
Length mm
PU
Price / Order description 100 pieces JT3-D-6H-5,5/6,3x67-E16 JT3-D-6H-5,5/6,3x87-E16 JT3-D-6H-5,5/6,3x107-E16 JT3-D-6H-5,5/6,3x127-E16 JT3-D-6H-5,5/6,3x147-E16 JT3-D-6H-5,5/6,3x167-E16 JT3-D-6H-5,5/6,3x197-E16 JT3-D-6H-5,5/6,3x237-E16 JT3-D-6H-5,5/6,3x67-E19 JT3-D-6H-5,5/6,3x87-E19 JT3-D-6H-5,5/6,3x107-E19 JT3-D-6H-5,5/6,3x127-E19 JT3-D-6H-5,5/6,3x147-E19 JT3-D-6H-5,5/6,3x167-E19 JT3-D-6H-5,5/6,3x197-E19 JT3-D-6H-5,5/6,3x237-E19 JT3-D-6H-5,5/6,3x67-E22 JT3-D-6H-5,5/6,3x87-E22 JT3-D-6H-5,5/6,3x107-E22 JT3-D-6H-5,5/6,3x127-E22 JT3-D-6H-5,5/6,3x147-E22 JT3-D-6H-5,5/6,3x167-E22 JT3-D-6H-5,5/6,3x197-E22 JT3-D-6H-5,5/6,3x237-E22
Part number
64
Acces sor ie s
Sealing washer E16, 16 mm 5.5 6.3 67 35.0 - 40.0 5.5 6.3 87 48.0 - 60.0 5.5 6.3 107 58.0 - 80.0 5.5 6.3 127 72.0 - 100.0 5.5 6.3 147 92.0 - 120.0 5.5 6.3 167 112.0 - 140.0 5.5 6.3 197 140.0 - 170.0 5.5 6.3 237 170.0 - 210.0 Sealing washer E19, 19 mm 5.5 6.3 67 35.0 - 40.0 5.5 6.3 87 48.0 - 60.0 5.5 6.3 107 58.0 - 80.0 5.5 6.3 127 72.0 - 100.0 5.5 6.3 147 92.0 - 120.0 5.5 6.3 167 112.0 - 140.0 5.5 6.3 197 140.0 - 170.0 5.5 6.3 237 170.0 - 210.0 Sealing washer E22, 22 mm 5.5 6.3 67 35.0 - 40.0 5.5 6.3 87 48.0 - 60.0 5.5 6.3 107 58.0 - 80.0 5.5 6.3 127 72.0 - 100.0 5.5 6.3 147 92.0 - 120.0 5.5 6.3 167 112.0 - 140.0 5.5 6.3 197 140.0 - 170.0 5.5 6.3 237 170.0 - 210.0 Order information: Further lengths upon request.
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
250 200 200 150 150 150 100 100 250 200 200 150 150 150 100 100 200 150 150 100 100 100 100 50
3554511372 3556011371 3556111371 3556211371 3556311371 3556711371 3559711372 3559611372 3554566372 3556066371 3556166371 3556266371 3556366371 3556766371 3559766372 3559666372 3554513372 3556013371 3556113371 3556213371 3556313371 3556713371 3559713372 3559613372
Inst al l at i on to ol s
Self-drilling screws JT3 / JF3 A2 stainless steel with steel point EJOT SUPER-SAPHIR Self-drilling screw JT3-D-12H-5,5/6,3
J3
S el f-dri l l i ng screw s
FEATURES A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head High thread APPROVAL Z-14.4-407 TECHNICAL DATA Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-12-5,5 .................. Self-tapping screw JZ3-6,3 ...................... Self-tapping screw JZ7-6,3 ...................... Special screwgun DAM5 ..........................
mm
high thread mm
Length mm
PU
Price / Order description 100 pieces JT3-D-12H-5,5/6,3x75-E16 JT3-D-12H-5,5/6,3x95-E16 JT3-D-12H-5,5/6,3x115-E16 JT3-D-12H-5,5/6,3x135-E16 JT3-D-12H-5,5/6,3x155-E16 JT3-D-12H-5,5/6,3x175-E16 JT3-D-12H-5,5/6,3x195-E16 JT3-D-12H-5,5/6,3x245-E16 JT3-D-12H-5,5/6,3x75-E19 JT3-D-12H-5,5/6,3x95-E19 JT3-D-12H-5,5/6,3x115-E19 JT3-D-12H-5,5/6,3x135-E19 JT3-D-12H-5,5/6,3x155-E19 JT3-D-12H-5,5/6,3x175-E19 JT3-D-12H-5,5/6,3x195-E19 JT3-D-12H-5,5/6,3x245-E19 JT3-D-12H-5,5/6,3x75-E22 JT3-D-12H-5,5/6,3x95-E22 JT3-D-12H-5,5/6,3x115-E22 JT3-D-12H-5,5/6,3x135-E22 JT3-D-12H-5,5/6,3x155-E22 JT3-D-12H-5,5/6,3x175-E22 JT3-D-12H-5,5/6,3x195-E22 JT3-D-12H-5,5/6,3x245-E22
Part number
65
Acces sor ie s
Sealing washer E16, 16 mm 5.5 6.3 75 36.0 - 40.0 5.5 6.3 95 48.0 - 60.0 5.5 6.3 115 58.0 - 80.0 5.5 6.3 135 72.0 - 100.0 5.5 6.3 155 92.0 - 120.0 5.5 6.3 175 110.0 - 140.0 5.5 6.3 195 130.0 - 160.0 5.5 6.3 245 170.0 - 210.0 Sealing washer E19, 19 mm 5.5 6.3 75 36.0 - 40.0 5.5 6.3 95 48.0 - 60.0 5.5 6.3 115 58.0 - 80.0 5.5 6.3 135 72.0 - 100.0 5.5 6.3 155 92.0 - 120.0 5.5 6.3 175 110.0 - 140.0 5.5 6.3 195 130.0 - 160.0 5.5 6.3 245 170.0 - 210.0 Sealing washer E22, 22 mm 5.5 6.3 75 36.0 - 40.0 5.5 6.3 95 48.0 - 60.0 5.5 6.3 115 58.0 - 80.0 5.5 6.3 135 72.0 - 100.0 5.5 6.3 155 92.0 - 120.0 5.5 6.3 175 110.0 - 140.0 5.5 6.3 195 130.0 - 160.0 5.5 6.3 245 170.0 - 210.0 Order information: Further lengths upon request.
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For fixing rail systems with intermediate insulation to thin-walled steel / aluminium substructure as well as timber substructure For xing wooden parts onto thin-walled steel / aluminium substructure FEATURES A2 stainless steel with hardened drill point APPROVAL Z-14.4-426 TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180 mm 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 Length mm 60 80 100 120 140 160 180 200 Clamp thickness mm 17 - 45 17 - 65 37 - 85 57 - 105 77 - 125 97 - 145 117 - 165 137 - 185 PU 250 250 250 200 150 150 150 150 Price / Order description 100 pcs. JT3-ST-2-6,0x60 JT3-ST-2-6,0x80 JT3-ST-2-6,0x100 JT3-ST-2-6,0x120 JT3-ST-2-6,0x140 JT3-ST-2-6,0x160 JT3-ST-2-6,0x180 JT3-ST-2-6,0x200 Part number 7382125301 7382107301 7382101301 7382102301 7382103301 7382104301 7382105301 7382106301
R i vets
S peci a l screw s
S torm w a shers
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For fixing standing seam systems (clips) to 0,55 1,25 mm steel substructure For xing standing seam systems (clips) to 0,8 1,5 mm aluminium substructure and timber substructure Embedment depth acc. to the approval 18 24 mm FEATURES A2 stainless steel with hardened drill point Under-head serrations to increase the installation reliability Special thread for thin-walled components High stripping torque Installation without special tools APPROVAL Z-14.4-426 TECHNICAL DATA Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
Length mm 25 36 46
Clamp thickness mm 0 - 10 0 - 20 0 - 30
66
Acces sor ie s
Inst al l at i on to ol s
Self-drilling screws JT4 A2 stainless steel EJOT stainless steel SAPHIR Self-drilling screw JT4-2-4,8
J4
S el f-dri l l i ng screw s
FEATURES A2 stainless steel Stainless steel sealing washer mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT4-2-4,8x19 JT4-2-4,8x19-E14 Part number TECHNICAL DATA Drilling capacity tI + tII ................................... 1,0 + 1,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
without sealing washer 4.8 19 0-9 Sealing washer E14, 14 mm 4.8 19 0-6
1,000
3501909420
APPLICATION RANGE Side lap stitching of aluminium corrugated profile sheets FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under screw head for side lap stitching mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT4-FR-2H-4,8x19-E11 Part number TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 1,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
1,000
3501968458
67
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
1,000
7380402300
S peci a l screw s
S torm w a shers
APPLICATION RANGE Especially suited for xing aluminium proles to aluminium substructure
APPLICATION RANGE For xing aluminium corrugated prole sheets to timber substructure For xing facade panels to timber substructure FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer Thread according to DIN 7998 APPROVAL Z-14.1-537 TECHNICAL DATA Drilling capacity .............................................. 0,5 - 2,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180 mm Length mm PU Price / Order description 100 pcs. JT4-FR-2-4,9x35-E11 Part number
S peci a l screw s
S torm w a shers
500
3503568420
P ipe f lashings
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For xing aluminium proles to aluminium substructure 2 mm FEATURES A2 stainless steel TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 2,0 mm Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 68 Special screwgun DAM5 .......................... page 68 mm Length mm Clamp thickness mm 0-7 0 - 10 PU Price / Order description 100 pcs. JT4-ZT-3-4,2x13 JT4-ZT-3-4,2x16 Part number
1,000 1,000
7381098300 7381074300
68
Acces sor ie s
Inst al l at i on to ol s
Self-drilling screws JT4 A2 stainless steel EJOT stainless steel SAPHIR Self-drilling screw JT4-3H/5-5,5
J4
S el f-dri l l i ng screw s
JT4-3H/5-5,5x19*
7380540300
APPLICATION RANGE For xing aluminium proles to aluminium substructure 3 mm mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT4-4-4,8x19 JT4-4-4,8x19-E11 JT4-4-4,8x19-E14 Part number FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer APPROVAL / TEST CERTIFICATE Z-14.1-537 P-043606 P-043609 TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 3,0 mm Drive ............................................................ hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
1,000
3501909440
69
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 4.8 19 0 - 11 Sealing washer E11, 11 mm 4.8 19 0-8 Sealing washer E14, 14 mm 4.8 19 0-8
1,000 1,000
7380387300 3501968440
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
NOTE Self-drilling screw for fastening 3mm pre-drilled wall support to 2 mm prole. Component I: 3,0 mm / Bauteil II: 1,6 2,0 mm
R i vets
S peci a l screw s
mm
Length mm
PU
Part number
FEATURES A2 stainless steel Installation without depth control / torque clutch Exact design of fixed or floating points Flange head, 13 mm
S torm w a shers
APPLICATION RANGE To form oating and xed points on aluminium substructures of rear ventilated facades
APPLICATION RANGE For xing aluminium corrugated prole sheets to aluminium substructure 3 mm For xing facade panels to aluminium substructure FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 3,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
S torm w a shers
mm
Length mm
Clamp thickness mm
PU
Part number
without sealing washer 4.8 19 0 - 11 Sealing washer E11, 11 mm 4.8 19 0-8 Sealing washer E14, 14 mm 4.8 19 0-8
S peci a l screw s
P ipe f lashings
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For xing aluminium proles to aluminium substructure 3 mm FEATURES A2 stainless steel TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 3,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm 0 - 11 0 - 17
PU
Part number
1,000 1,000
7381118300 7381129300
70
Acces sor ie s
Inst al l at i on to ol s
Self-drilling screws JT4 A2 stainless steel EJOT stainless steel SAPHIR Self-drilling screw JT4-FR-4-5,5
with truss head
S el f-dri l l i ng screw s
mm
Length mm
Clamp thickness mm
PU
Part number
APPLICATION RANGE For xing aluminium corrugated prole sheets to aluminium substructure 3 mm For xing facade panels to aluminium substructure FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drilling capacity tI + tII ....................................1,0 + 3,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
1,000
3501869448
J4
APPLICATION RANGE Fastening aluminium proles to aluminium substructure 4 mm mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JT4-6-5,5x19 JT4-6-5,5x22* JT4-6-5,5x30 JT4-6-5,5x19-E14 JT4-6-5,5x22-E14 JT4-6-5,5x30-E14 JT4-6-5,5x22-E16 JT4-6-5,5x30-E16 Part number FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer APPROVAL / TEST CERTIFICATE Z-14.1-537 P-043609 TECHNICAL DATA Drilling capacity tI + tII ....................................2,0 + 4,0 mm drive............................................................. hexagon A/F8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
71
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 5.5 19 0 - 7 1,000 5.5 22 0 - 10 1,000 5.5 30 0 - 18 500 Sealing washer E14, 14 mm 5.5 19 0-4 500 5.5 22 0 - 7 1,000 5.5 30 0 - 15 500 Sealing washer E16, 16 mm 5.5 22 0-7 500 5.5 30 0 - 15 500 *JT9 made of A4 stainless steel, upon request
3502111460 3502311461
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
1,000
7381138300
S torm w a shers
S torm w a shers
APPLICATION RANGE For xing bre cement corrugated sheets to timber substructures FEATURES A2 stainless steel Pre-assembled FZD sealing washer A2 stainless steel washer Screw wings save additional drilling into the corrugated slabs No forcing tension APPROVAL Z-31.1-144 (Eternit) TECHNICAL DATA drive............................................................. hexagon A/F8 NOTE Suitable for covering with bre cement corrugated sheets prole 177/51 P5 and P6 to timber substructure without insulation. For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals. mm 6.5 Length mm 130 PU 100 Price / Order description 100 pcs. JT4-FZ-6,5x130-FZD Part number 3515675400
R i vets
S peci a l screw s
72
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
CROSS REFERENCE Accessories ............................................ page 191 Self-drilling screw JT2-FZ-F-6,5 ............... page 51 Special screwgun DAM5 .......................... page 180
Self-drilling screws JT4 A2 stainless steel EJOT stainless steel SAPHIR Self-drilling screw JT4-S-2-4,8
S el f-dri l l i ng screw s
APPLICATION RANGE For xing timber laths to aluminium substructure 2 mm FEATURES A2 stainless steel Countersunk head with milling ribs TEST CERTIFICATE P-013604 P-BWU02-064191 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191
mm 4.8 4.8
Length mm 38 48
500 500
JT4-S-2-4,8x38 JT4-S-2-4,8x48
7382086300 7382072300
mm 4.8
Length mm 35
Clamp thickness mm 0 - 27
PU 500
FEATURES A2 stainless steel Countersunk head with flange TECHNICAL DATA Drilling capacity tI + tII .............................................3,0 mm Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191
73
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
PU
Part number
S torm w a shers
74
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P. Lange
THE DUBAI MALL, DUBAI Delivered by EJOT: EJOT Self-tapping screw JZ3
Self-tapping screws
PRODUCT VERSIONS EJOT Self-tapping screws JA2/JZ2 JA3/JZ3 JA1/JZ1 Corremaks JZ7 CRONIMAKS
steel/wood
steel/aluminium/ wood
steel/aluminium/ wood
DRILL HOLE- FOR PROFILED STEEL SHEET-DESIGNS Hot dip galvanised sheet steel / sectional steel, at steel St 37 (Rm 360 N/mm 440 N/mm) 2x 2x 2x 0.63 0.75 0.88 1.00 1.13 1.25 1.50 2.0 - 4.9 5.0 - 6.9 7.0 1.5 - 5.9 6.0 - 7.9 8.0 - 9.9 10.0 0.75 0.88 1.00 3.5 4.0 4.5 4.5 4.5 4.5 5.0 4.5 5.0 5.0 5.3 5.5 5.7 6.8 7.0 7.2 7.4 JA 6,5 / JB 6,3 JZ 6,3 JZ 8,0
DRILL HOLE- FOR ALUMINIUM PROFILED SHEET-DESIGNS/* Aluminium sheet, aluminium extrusion prole F22 up to F 25 (Rm 220 N/mm 290 N/mm) up to 0.9 1.0 - 1.4 1.5 - 2.9 3.0 - 4.9 5.0 4.0 4.0 4.5 5.0 5.3 JA 6,5 / JB 6,3 JZ 6,3
Component I
Component II
Component I
Inst al l at i on to ol s
75
Acces sor ie s
* When fastening aluminium proled sheet (component I) onto steel substrate (component II) the drill-hole- from the chart for proled steel sheet designs apply.
Component II
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
For self-tapping fasteners without drill point the cylindrical part of the screw has to be fastened at least 6 mm into the load-bearing component. In practice 20 mm are added to the sum of the thickness of all components that are fastened onto the substructure. The result is the minimum screw length of a self-tapping screw under consideration of sealing washer and assembly unevenness.
R i vets
S peci a l screw s
Screw Material
A2 stainless steel
A2 stainless steel
S torm w a shers
S el f-dri l l i ng screw s
S torm w a shers
APPLICATION RANGE Fixing proled steel sheets to timber substructure Fixing proled steel sheets to 2 mm steel substrate Side lap stitching FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180 mm Length mm 19 25 32 38 50 64 75 90 100 125 150 175 200 Packaging unit 500 500 500 500 250 250 250 200 200 150 100 100 100 Price / Order description 100 pcs. JA2-6,5x19-V16 JA2-6,5x25-V16 JA2-6,5x32-V16 JA2-6,5x38-V16 JA2-6,5x50-V16 JA2-6,5x64-V16 JA2-6,5x75-V16 JA2-6,5x90-V16 JA2-6,5x100-V16 JA2-6,5x125-V16 JA2-6,5x150-V16 JA2-6,5x175-V16 JA2-6,5x200-V16 Part number
S peci a l screw s
P ipe f lashings
Sealing washer V16, 16 mm 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5
3183121654 3183221654 3183321654 3183421654 3183621654 3183821654 3183921654 3184121654 3184221654 3114421651 3114621651 3114721651 3114821651
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Fixing proled steel sheets to steel substrate FEATURES Case-hardened steel, zinc-plated Steel sealing washer, zinc-plated Pre-assembled sealing washer TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Packaging unit 500 500 500 500 250 250 200 200 200 150 100 100 100
Price / Order description 100 pcs. JZ2-6,3x19-V16 JZ2-6,3x25-V16 JZ2-6,3x32-V16 JZ2-6,3x38-V16 JZ2-6,3x50-V16 JZ2-6,3x64-V16 JZ2-6,3x80-V16 JZ2-6,3x90-V16 JZ2-6,3x100-V16 JZ2-6,3x125-V16 JZ2-6,3x150-V16 JZ2-6,3x175-V16 JZ2-6,3x200-V16
Part number
76
Acces sor ie s
Sealing washer V16, 16 mm 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3
3181121654 3181221654 3181321654 3181421654 3181621654 3181821654 3182021654 3182121654 3182221654 3112421651 3112621651 3112721651 3112821651
Inst al l at i on to ol s
ATOMIUM, BRUSSELS, BELGIUM Supplied by EJOT: EJOT SUPER-SAPHIR Self-drilling screw JT3
CUiNZ
R i vets
77
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
APPLICATION RANGE For xing proled steel sheets to timber substructure For xing sandwich panels to timber substructure For xing proled steel / aluminium sheet to 2 mm steel substructure Side lap stitching of proled steel / aluminium sheet APPROVAL ETA-10/0200 Z-14.4-407 Z-14.1-537 TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-2-6,5 .................... Storm washers ........................................ Special screwgun DAM5 ..........................
R i vets
S peci a l screw s
S torm w a shers
mm
Length mm
PU
Price / Order description 100 pcs. JA3-6,5x19-E16 JA3-6,5x25-E16 JA3-6,5x32-E16 JA3-6,5x38-E16 JA3-6,5x45-E16 JA3-6,5x50-E16 JA3-6,5x64-E16 JA3-6,5x75-E16 JA3-6,5x90-E16 JA3-6,5x100-E16 JA3-6,5x115-E16 JA3-6,5x125-E16 JA3-6,5x150-E16 JA3-6,5x175-E16 JA3-6,5x200-E16 JA3-6,5x230-E16 JA3-6,5x260-E16 JA3-6,5x290-E16 JA3-6,5x19-E19 JA3-6,5x25-E19 JA3-6,5x32-E19 JA3-6,5x38-E19 JA3-6,5x45-E19 JA3-6,5x50-E19 JA3-6,5x64-E19 JA3-6,5x75-E19 JA3-6,5x90-E19 JA3-6,5x100-E19 JA3-6,5x115-E19 JA3-6,5x125-E19 JA3-6,5x150-E19 JA3-6,5x175-E19 JA3-6,5x200-E19 JA3-6,5x230-E19 JA3-6,5x260-E19 JA3-6,5x290-E19
Part number
78
Acces sor ie s
Sealing washer E16, 16 mm 6.5 19 500 6.5 25 500 6.5 32 500 6.5 38 500 6.5 45 500 6.5 50 250 6.5 64 250 6.5 75 250 6.5 90 200 6.5 100 200 6.5 115 150 6.5 125 150 6.5 150 100 6.5 175 100 6.5 200 100 6.5 230 100 6.5 260 100 6.5 290 150 Sealing washer E19, 19 mm 6.5 19 500 6.5 25 500 6.5 32 500 6.5 38 500 6.5 45 250 6.5 50 250 6.5 64 250 6.5 75 200 6.5 90 200 6.5 100 200 6.5 115 150 6.5 125 150 6.5 150 100 6.5 175 100 6.5 200 100 6.5 230 100 6.5 260 100 6.5 290 100 Sealing washer E22, 22 mm (see next page)
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
3113111311 3113211311 3113311311 3113411311 3113511311 3113611311 3113811311 3113911311 3114111311 3114211311 3114311311 3114411311 3114611311 3114711311 3114811311 3114911311 3110911311 3116211311 3113112311 3113212311 3113312311 3113412311 3113512311 3113612311 3113812311 3113912311 3114112311 3114212311 3114312311 3114412311 3114612311 3114712311 3114812311 3114912311 3110912311 3116212311
Inst al l at i on to ol s
P ipe f lashings
Self-tapping screws JA3 / JZ3 A2 stainless steel EJOT Self-tapping screw JA3-6,5
J3
S el f-dri l l i ng screw s
APPLICATION RANGE For xing proled steel sheets to timber substructure For xing sandwich panels to timber substructure For xing proled steel / aluminium sheet to 2 mm steel substructure Side lap stitching of proled steel / aluminium sheet APPROVAL ETA-10/0200 Z-14.4-407 Z-14.1-537 TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-2-6,5 .................... Storm washers ........................................ Special screwgun DAM5 ..........................
mm
Length mm 19 25 32 38 45 50 64 75 90 100 115 125 150 175 200 230 260 290
PU
Price / Order description 100 pcs. JA3-6,5x19-E22 JA3-6,5x25-E22 JA3-6,5x32-E22 JA3-6,5x38-E22 JA3-6,5x45-E22 JA3-6,5x50-E22 JA3-6,5x64-E22 JA3-6,5x75-E22 JA3-6,5x90-E22 JA3-6,5x100-E22 JA3-6,5x115-E22 JA3-6,5x125-E22 JA3-6,5x150-E22 JA3-6,5x175-E22 JA3-6,5x200-E22 JA3-6,5x230-E22 JA3-6,5x260-E22 JA3-6,5x290-E22
Part number
79
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Sealing washer E22, 22 mm 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5
500 500 200 200 250 250 200 150 150 150 100 100 100 100 100 50 100 100
3113113311 3113213311 3113313311 3113413311 3113513311 3113613311 3113813311 3113913311 3114113311 3114213311 3114313311 3114413311 3114613311 3114713311 3114813311 3114913311 3110913311 3116213311
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For xing proled steel sheets/sandwich panels to steel substructure For xing steel / aluminium proled sheets to aluminium substructures FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer APPROVAL ETA-10/0200 Z-14.4-407 Z-14.1-537 TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-6-5,5 .................... Self-drilling screw JT3-12-5,5 .................. Storm washers ........................................ Special screwgun DAM5 ..........................
S peci a l screw s
S torm w a shers
mm
Length mm
PU
Price / Order description 100 pcs. JZ3-6,3x19-E16 JZ3-6,3x25-E16 JZ3-6,3x32-E16 JZ3-6,3x38-E16 JZ3-6,3x50-E16 JZ3-6,3x64-E16 JZ3-6,3x80-E16 JZ3-6,3x90-E16 JZ3-6,3x100-E16 JZ3-6,3x115-E16 JZ3-6,3x125-E16 JZ3-6,3x135-E16 JZ3-6,3x150-E16 JZ3-6,3x175-E16 JZ3-6,3x200-E16 JZ3-6,3x230-E16 JZ3-6,3x270-E16 JZ3-6,3x19-E19 JZ3-6,3x25-E19 JZ3-6,3x32-E19 JZ3-6,3x38-E19 JZ3-6,3x50-E19 JZ3-6,3x64-E19 JZ3-6,3x80-E19 JZ3-6,3x90-E19 JZ3-6,3x100-E19 JZ3-6,3x115-E19 JZ3-6,3x125-E19 JZ3-6,3x135-E19 JZ3-6,3x150-E19 JZ3-6,3x175-E19 JZ3-6,3x200-E19 JZ3-6,3x230-E19 JZ3-6,3x270-E19
Part number
R i vets
P ipe f lashings
Sealing washer E16, 16 mm 6.3 19 500 6.3 25 500 6.3 32 500 6.3 38 500 6.3 50 250 6.3 64 250 6.3 80 200 6.3 90 200 6.3 100 200 6.3 115 150 6.3 125 150 6.3 135 100 6.3 150 100 6.3 175 100 6.3 200 100 6.3 230 100 6.3 270 100 Sealing washer E19, 19 mm 6.3 19 500 6.3 25 500 6.3 32 500 6.3 38 500 6.3 50 250 6.3 64 250 6.3 80 200 6.3 90 200 6.3 100 200 6.3 115 150 6.3 125 150 6.3 135 100 6.3 150 100 6.3 175 100 6.3 200 100 6.3 230 100 6.3 270 100 Sealing washer E22, 22 mm (see next page)
3111111311 3111211311 3111311311 3111411311 3111611311 3111811311 3112011311 3112111311 3112211311 3112311311 3112411311 3112511311 3112611311 3112711311 3112811311 3112911311 3110611311 3111112311 3111212311 3111312311 3111412311 3111612311 3111812311 3112012311 3112112311 3112212311 3112312311 3112412311 3112512311 3112612311 3112712311 3112812311 3112912311 3110612311
80
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Self-tapping screws JA3 / JZ3 A2 stainless steel EJOT Self-tapping screw JZ3-6,3
J3
S el f-dri l l i ng screw s
APPLICATION RANGE For xing proled steel sheets/sandwich panels to steel substructure For xing steel/aluminium proled sheets to aluminium substructures FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer Part number APPROVAL ETA-10/0200 Z-14.4-407 Z-14.1-537 TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ Self-drilling screw JT3-6-5,5 .................... Self-drilling screw JT3-12-5,5 .................. Storm washers ........................................ Special screwgun DAM5 ..........................
mm
Length mm 19 25 32 38 50 64 80 90 100 115 125 135 150 175 200 230 270
PU
Price / Order description 100 pcs. JZ3-6,3x19-E22 JZ3-6,3x25-E22 JZ3-6,3x32-E22 JZ3-6,3x38-E22 JZ3-6,3x50-E22 JZ3-6,3x64-E22 JZ3-6,3x80-E22 JZ3-6,3x90-E22 JZ3-6,3x100-E22 JZ3-6,3x115-E22 JZ3-6,3x125-E22 JZ3-6,3x135-E22 JZ3-6,3x150-E22 JZ3-6,3x175-E22 JZ3-6,3x200-E22 JZ3-6,3x230-E22 JZ3-6,3x270-E22
81
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Sealing washer E22, 22 mm 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3
500 500 200 200 250 200 150 150 150 100 100 100 100 100 100 50 100
3111113311 3111213311 3111313311 3111413311 3111613311 3111813311 3112013311 3112113311 3112213311 3112313311 3112413311 3112513311 3112613311 3112713311 3112813311 3112913311 3110613311
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE Side lap stitching of proled steel sheets in highly corosive environments Fixing proled steel sheets to timber substructures in highly corrosive environments FEATURES A5 stainless steel 1.4529 Stainless steel sealing washer Pre-assembled sealing washer Highest corrosion protection class APPROVAL ETA-10/0200 TECHNICAL DATA Drive ........................................................hexagon A/F3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
S torm w a shers
mm
Length mm
Clamp thickness mm
PU
Price / Order description 100 pcs. JA1-6,5x22 JA1-6,5x38 JA1-6,5x64 JA1-6,5x115 JA1-6,5x22-E16 JA1-6,5x38-E16 JA1-6,5x64-E16 JA1-6,5x115-E16
Part number
P ipe f lashings
without sealing washer 6.5 22 0-9 6.5 38 0 - 25 6.5 64 0 - 51 6.5 115 40 - 102 Sealing washer E16, 16 mm 6.5 22 0-6 6.5 38 0 - 22 6.5 64 0 - 48 6.5 115 40 - 99
S peci a l screw s
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE Fixing proled steel sheets to steel substrate in highly corrosive environments FEATURES A5 stainless steel 1.4529 Stainless steel sealing washer Pre-assembled sealing washer Highest corrosion protection class APPROVAL ETA-10/0200 TECHNICAL DATA Drive ........................................................hexagon A/F3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm
Clamp thickness mm
PU
Part number
without sealing washer 6.3 22 0-9 Sealing washer E16, 16 mm 6.3 22 0-6
500 500
3111200319 3111211319
82
Acces sor ie s
Inst al l at i on to ol s
Self-tapping screws JZ7 A2 stainless steel EJOT CRONIMAKS Self-tapping screw JZ7-6,3
J7
S el f-dri l l i ng screw s
APPLICATION RANGE Fixing proled steel sheet / sandwich panels to steel substrate up to S 355 (St 52) Fixing proled steel sheet / sandwich panels to stainless steel substrate (up to Rm = 700 N/mm) mm Length mm Clamp thickness mm PU Price / Order description 100 pcs. JZ7-6,3x22-E16/2 JZ7-6,3x65-E16/2 JZ7-6,3x85-E16/2 JZ7-6,3x105-E16/2 JZ7-6,3x125-E16/2 JZ7-6,3x145-E16/2 JZ7-6,3x165-E16/2 JZ7-6,3x185-E16/2 JZ7-6,3x22-E19/3 JZ7-6,3x65-E19/3 JZ7-6,3x85-E19/3 JZ7-6,3x105-E19/3 JZ7-6,3x125-E19/3 JZ7-6,3x145-E19/3 JZ7-6,3x165-E19/3 JZ7-6,3x185-E19/3 JZ7-6,3x22-E22/3 JZ7-6,3x65-E22/3 JZ7-6,3x85-E22/3 JZ7-6,3x105-E22/3 JZ7-6,3x125-E22/3 JZ7-6,3x145-E22/3 JZ7-6,3x165-E22/3 JZ7-6,3x185-E22/3 Part number FEATURES Approved A2 stainless steel screw for high-strength steel substructures Stainless steel sealing washer Pre-assembled sealing washer APPROVAL ETA-10/0200 Z-14.4-407 TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ page 191 Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
83
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Sealing washer E16/2, 16 mm 6.3 22 0-6 6.3 65 0 - 49 6.3 85 20 - 69 6.3 105 40 - 89 6.3 125 60 - 109 6.3 145 80 - 129 6.3 165 100 - 149 6.3 185 120 - 169 Sealing washer E19/3, 19 mm 6.3 22 0-6 6.3 65 0 - 49 6.3 85 20 - 69 6.3 105 40 - 89 6.3 125 60 - 109 6.3 145 80 - 129 6.3 165 100 - 149 6.3 185 120 - 169 Sealing washer E22/3, 22 mm 6.3 22 0-6 6.3 65 0 - 49 6.3 85 20 - 69 6.3 105 40 - 89 6.3 125 60 - 109 6.3 145 80 - 129 6.3 165 100 - 149 6.3 185 120 - 169
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
84
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Olaf Schuelke
THE ADDRESS HOTEL, DUBAI Supplied by EJOT: EJOT insulation support anchor DH
Storm washers
Crown width mm
Prole height mm
Valley distance mm
85
Acces sor ie s
Inst al l at i on to ol s
FAX REPLY Please fax the three values to the following fax number: +49 2752 908-731
INSTALLATION RELIABILITY An EJOT storm washer also guarantees installation reliability. The installer always hits the middle of the crown after applying the storm washer which prevents scratching of the surface. It enables an increased clamping force on the component, without plastic deformation. The increased loads due to the use of EJOT storm washers are documented in various building authorities test certicates (type statistics) of aluminium trapezoidal proles.
SELECTION AID Our application engineering will gladly assist you in selecting the right choice of storm washer. We need the following three values in mm: Crown width Profile height Valley width
REQUIREMENTS EJOT ORKAN storm washer have to full multiple requirements. They utilise a consistent load distribution of the crown xing of a trapezoidal proled sheets or sandwich elements. The pronounced reinforcement anges of the EJOT storm washers are a guarantee for high dimensional stability and consistent load transmission. As a so-called second insulation level the EJOT storm washer permanently buffers the xed size between upper substructure edge. The screw head and the crown of a sheet is often slightly convex or concave and in order to compensate these tolerances a soft closed-cell rubber is ideal. No bridging arises where humidity can enter the fastener shank and thus the inside of the building. The permanent compression required for the lasting watertightness of this cellular rubber is minimal and the deformation of a thin-walled trapezoidal proled sheet can thus be prevented during installation.
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S el f-dri l l i ng screw s
Storm washers
S el f-dri l l i ng screw s
R i vets
Acces sor ie s
Storm Angle of washer inclinawidth mm tion Alu self colour 20 34 21 16 21 25 26 15 26 27 26 34 31 31 31 37 32 25 35 23 36 40 41 16 41 32 41 39 53 36 55 32 Alu coloured 20 34 21 16 21 25 26 15 26 27 26 34 31 31 31 37 32 25 35 23 36 40 41 16 41 32 41 39 53 36 55 32 Alu-stucco 20 34 21 16 21 25 26 15 26 27 31 31 31 37 32 25 35 23 36 40 41 16 41 32 41 39 53 36 55 32
Crown width mm 19 20 20 25 25 25 30 30 31 34 35 40 40 40 52 54 19 20 20 25 25 25 30 30 31 34 35 40 40 40 52 54 19 20 20 25 25 30 30 31 34 35 40 40 40 52 54
PU
Price /100 Order description pcs. Storm washer 20-34 alu self colour Storm washer 21-16 alu self colour Storm washer 21-25 alu self colour Storm washer 26-15 alu self colour Storm washer 26-27 alu self colour Storm washer 26-34 alu self colour Storm washer 31-31 alu self colour Storm washer 31-37 alu self colour Storm washer 32-25 alu self colour Storm washer 35-23 alu self colour Storm washer 36-40 alu self colour Storm washer 41-16 alu self colour Storm washer 41-32 alu self colour Storm washer 41-39 alu self colour Storm washer 53-36 alu self colour* Storm washer 55-32 alu self colour Storm washer 20-34 alu** Storm washer 21-16 alu** Storm washer 21-25 alu** Storm washer 26-15 alu** Storm washer 26-27 alu** Storm washer 26-34 alu** Storm washer 31-31 alu** Storm washer 31-37 alu** Storm washer 32-25 alu** Storm washer 35-23 alu** Storm washer 36-40 alu** Storm washer 41-16 alu** Storm washer 41-32 alu** Storm washer 41-39 alu** Storm washer 53-36 alu** Storm washer 55-32 alu** Storm washer 20-34 alu stucco Storm washer 21-16 alu stucco Storm washer 21-25 alu stucco Storm washer 26-15 alu stucco Storm washer 26-27 alu stucco Storm washer 31-31 alu stucco Storm washer 31-37 alu stucco Storm washer 32-25 alu stucco Storm washer 35-23 alu stucco Storm washer 36-40 alu stucco Storm washer 41-16 alu stucco Storm washer 41-32 alu stucco Storm washer 41-39 alu stucco Storm washer 53-36 alu stucco* Storm washer 55-32 alu stucco
Part number
500 500 500 500 500 500 500 500 500 500 500 500 500 500 400 400 500 500 500 500 500 500 500 500 500 500 500 500 500 500 400 400 500 500 500 500 500 500 500 500 500 500 500 500 500 400 400
3046700110 3046600110 3052125000 3046900110 3047000110 3052634000 3053132000 3045900110 3053124000 3046100110 3053538000 3046200110 3049200110 3054139000 3055336000 3049500110 3046700119 3046600119 3046900119 3047000119 3045900119 3046100119 3063640000 3046200119 3049200119 3085336000 3049500119
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
* Storm washer can be supplied with centrally located hole or in special shape with off-centre hole for crown corrugated proles * add four-digit RAL reference.
86
Storm washers
Radius mm
Length mm
PU
Part number
50 50 50
Storm washer W24 Alu stucco Storm washer W30 Alu stucco Storm washer W48 Alu stucco
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Manufacturer
Prole description alubel 28 alubel 21 alubel 40 alubel 44 Alutech Dach Aluform 20/125 Aluform 29/124 Aluform 30/153 Aluform 40/167 Aluform 42/250 Aluform 45/150 Aluform 45/200 Alutherm DT 900 Alutherm DT 1000 Corrugated sheet 18/76 Corrugated sheet 35/137 Corrugated sheet 55/177 AL 34/207 A 35/207 B 35/207 39/333 T AL 40/183 A 40/183 AL 42/333 S
Manufacturer
Prole description 44/180 AL 45/150 50/262.5 85/280 100/275 105/345 106/250 Ondatherm 1001 TS Ondabre 3005 T Agratherm 1001 TS Corrugated sheet 18/76 20/125 30/262K 35/207 40/183/183 S 50/250 50/262 58/315K 70/200 80/307 89/305 100/275 106/250 110/333
ALUBEL
BIEBER
ARCELOR
87
Acces sor ie s
Inst al l at i on to ol s
Aluform
41 - 32 26 - 38 41 - 32 31 - 31 26 - 27 41 - 32 20 - 34 26 - 34 35 - 23 31 - 31 26 - 27 41 - 24 26 - 27 31 - 31 W 24 W 43 W 48 41 - 39 35 - 47 41 - 16 26 - 27 41 - 16 41 - 24 31 - 21
ARCELOR
53 - 36 26 - 27 46 - 43 41 - 39 41 - 24 41 - 24 41 - 16 26 - 27 26 - 27 26 - 27 W24 41 - 32 41 - 44 41 - 32 41 - 16 41 - 39 46 - 43 53 - 36 53 - 18 41 - 32 41 - 32 41 - 24 41 - 16 41 - 16
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Alu self colour 24 18/76 30 27/111 42/160 and 55/177 48 Alu coloured 24 18/76 30 27/111 42/160 and 55/177 48 Alu-stucco 24 18/76 30 27/111 42/160 and 55/177 48 * add four-digit RAL colour code.
50 50 50 50 50 50
Storm washer W24 Alu self colour 3047700110 Storm washer W30 Alu self colour 3050030000 Storm washer W48 Alu self colour 3047400110 Storm washer W24 Alu* Storm washer W30 Alu* Storm washer W48 Alu* -
R i vets
S peci a l screw s
S el f-dri l l i ng screw s
Manufacturer
Prole description DP 20/35 DP 20/65 DP 20/100 DP 35/115 DP Sinus 18/76 DP Sinus 35/143 DP Sinus Variant 35/143 DP72/82/102/122/142/162 DP-F DS 20/115 DS 35/190 DS 35/206 DS Sinus 35/143 SISCOROOF 4G SISCOTEC ROOF 4G Dakproel 18 - 76 Dakproel 42 - 960 Dakproel 20 - 1090 Dakproel 35 - 1000 Dakproel 40 - 915 Dakproel 50 - 1000 Dakproel 58 - 945 KD Dakproel 70R - 800 35/207 40/183 50/250 85/280 100/275 Sinus 18 Sinus 27 Sinus 42 DL 70;80;100; 120;140;160 20/220 W-20/990 W-20/1100 W-45R/900 W-45ER/1000 W-155/840 W-1/1064 Penta 40 JI 33.250.1000 JI 45.333.1000 JI 35.207.1035 JI 40.183.915 JI 50.250.1000 JI 58.317.945 JI Roof 1000 JI Ecopaneel 1000 KS 1000 RW KS 1000 FF 35.207.1035 39.333.1000 KAS AL-20/125 A KAS AL-30/153 A KAS-35/207 KAS AL-40/167 A KAS-40/183 KAS AL-45/200 A KAS-50/250 KAS-85/280
Manufacturer
Prole description KAS-89/305 KAS -18/76 KAS -42/160 KAS -55/177 KAS -D 65 - 115 KAS -D 68 KAS -D 80 KAS -D 62 - 142 Isocopre Eurocinque Eurocopre 35 - 207 22 - 214 20 - 75 45 - 333 S 40 - 100 50 - 250 18 / 76 27 / 111 42 / 160 55 / 177 LP 20 LP 35 LP 1100 Sinus 18 LM40 250 1000 LM19 156 1094 LM 27-111-1000 20-75 22-214 35-207 40-100 45-150 45-333 S Corrugated sheet 18/76 Corrugated sheet 27/111 Corrugated sheet 55/177 G4 Hipertec Dach Hipertec Dach Sound Toproof DG SISCO SP 20 SP 26 SP 30 SP 35 SP 40 SP 41 SP 44 SP 45 SP 59 SP 80 MTD TL 65 MTD TL 85 MTD TL 105 MTD TL 125 MTD TL 145 SP 18/1064 SP 27/1000 SP 42/960 KP
Dansk Proltechnik
KLCKNER
BRUCHA
Lattonedil
S peci a l screw s
DS Staalprol
R i vets
Laukien
FINISH PROFILES
LINDAB
Luxmetall
FISCHER
P ipe f lashings
Maas
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
METECNO
ITALPANNELLI
Joriside
MONTANA
Acces sor ie s
Inst al l at i on to ol s
KLCKNER
M-Prol
88
Manufacturer
Prole description M 20/220 M 35/207 M 40/183 M 40/333 M 40KD/333 M 50/250 M 85/280 M 100/275 M 150/280 M 40/333 20,125/8 20,136/8 25,280/3 25,268/4 30,207/5 30,153/7 35,207/5 40,183/5 40,250/4 45,150/6 45,333/3 50,250/4 50,262.5/4 Corrugated sheet 18/76 Corrugated sheet 55.177 Corrugated sheet 27.111 Plannja 19 Plannja 20-102 Plannja 35 Sinus 18 Sinus 51 Plannja 20 Plannja 60 Plannja 30 Plannja 45 20/154 26/143 30/207 30/220 30 KD 35/207 40/183 45/150 45/333 50/250 58 KD 59/225 70/200 80/277 85/280 90/305 100/275 105/345 106/250 Corrugated sheet 18/76 Corrugated sheet 27/111 Corrugated sheet 42/160 Corrugated sheet 55/177 D62; D82; D102; D122; D142 19(KD)/1050 35R/1035
Manufacturer
Prole description 40R/915 50R/1000 70R/800 85R/1120 89R/915 100R/825 30KD/1050 45KD/1000 58KD/945 D 65-75-95-115-135 D 135.1000 TL 18 / 988 42 / 960 27 / 1000 PS 35/207 PS 40/183 PS 50/250 PS 85/280 PS 100/275 SIP D CB 18/76 CB 35/207 40/183 40/333 50/250 CB 75/305 85/280 100/275 Hoesch Thermodach T 35.1 T 40.1 T 50.1 T 85.1 T 100.1 T 106.1 WP 18/76 WP 42/160 WP 27/100 SNV WU 20/125 WU 30/200 WU 30D/207 WU 30W/207 WU 35/207 WU 40/183 WU 45/333 WU 50/250 WU 80/307 WU 100/275 WU 18/76 WU 27/111 WU 55/177 plusdach DL Ter Corrugated sheet 42/160 30,200/5 39,333/3 39/333 41/193.5
MNKER
SAB
SALZGITTER
O Metall
PLANNJA
TRIMO
PROGE
ROMAKOWSKI SAB
89
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
SIEGMETALL
R i vets
S peci a l screw s
APPLICATION RANGE For xing sandwich panels to concrete FEATURES Case-hardened steel Climadur coated high-quality coating to improve corrosion protection (15 Kesternich cycles, DIN 50018, 1997) TECHNICAL DATA Drive ............................................................ hexagon A/F8 Embedment depth ............................................... 30 mm Hole depth .......................................................... 45 mm NOTE Nominal drill diameter 5.0 mm CROSS REFERENCE Accessories ............................................ page 191
R i vets
S peci a l screw s
S torm w a shers
mm
Length mm
PU
Price / Order description 100 pcs. BS-R-6,3x35 BS-R-6,3x45 BS-R-6,3x100 BS-R-6,3x120 BS-R-6,3x140 BS-R-6,3x160 BS-R-6,3x180 BS-R-6,3x200 BS-R-6,3x220 BS-R-6,3x240 BS-R-6,3x35-V16 BS-R-6,3x45-V16 BS-R-6,3x100-V16 BS-R-6,3x120-V16 BS-R-6,3x140-V16 BS-R-6,3x160-V16 BS-R-6,3x180-V16 BS-R-6,3x200-V16 BS-R-6,3x220-V16 BS-R-6,3x240-V16
Part number
90
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 6.3 35 1000 6.3 45 500 6.3 100 250 6.3 120 200 6.3 140 200 6.3 160 200 6.3 180 200 6.3 200 150 6.3 220 150 6.3 240 150 V16 sealing washer, 16 mm 6.3 35 1000 6.3 45 500 6.3 100 250 6.3 120 200 6.3 140 200 6.3 160 200 6.3 180 200 6.3 200 150 6.3 220 150 6.3 240 150 Order information: Other sealing washers upon request
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
5663035512 5663045512 5663100512 5663120512 5663140512 5663160512 5663180512 5663200512 5663220512 5663240512 -
P ipe f lashings
mm
Length mm
PU
Price / Order description 100 pcs. JA3-FR-4,9x38 JA3-FR-4,9x64 JA3-FR-4,9x38-E14 JA3-FR-4,9x64-E14 JA3-FR-4,9x38-E14* JA3-FR-4,9x64-E14*
Part number
mm
Length mm
PU
Price / Order description 100 pcs. JA3-LT-4,9x25 JA3-LT-4,9x38 JA3-LT-4,9x25-E14 JA3-LT-4,9x38-E14 JA3-LT-4,9x25-E14* JA3-LT-4,9x38-E14*
Part number
APPLICATION RANGE For xing metal proles to timber substructure For xing metal proles to aluminium substructure 2mm TECHNICAL DATA Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
91
Acces sor ie s
Inst al l at i on to ol s
without sealing washer 4.9 25 1,000 4.9 38 1,000 Sealing washer self colour E14, 14 mm 4.9 25 500 4.9 38 500 Sealing washer E14, 14 mm, coloured 4.9 25 500 4.9 38 500 * add four-digit RAL colour code.
3233209312 3233409312
3233200312 5000638300
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
CROSS REFERENCE Accessories ............................................ page 191 FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
without sealing washer 4.9 38 500 4.9 64 500 Sealing washer self colour E14, 14 mm 4.9 38 500 4.9 64 250 Sealing washer E14, 14 mm, coloured 4.9 38 500 4.9 64 250 * add four-digit RAL colour code.
APPLICATION RANGE For fixing steel / aluminium proled sheets to timber substructure For xing steel / aluminium proled sheets to aluminium substructure 2mm FEATURES A2 stainless steel Stainless steel sealing washer Truss head and sealing washer self colour or coloured Pre-assembled sealing washer Thread according to DIN 7998 TECHNICAL DATA Drive ............................................ Hexalobular / TORX T25
3213509311 3213809311
R i vets
S peci a l screw s
3213500311 3213800311
S torm w a shers
APPLICATION RANGE For xing metal proles to timber substructure For xing metal proles to aluminium substructure 3 mm and steel substructure 2 mm FEATURES A2 stainless steel with countersunk head TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180 mm 6.5 6.5 Length mm 35 95 PU 500 200 Price / Order description 100 pcs. JA3-S-6,5x35 JA3-S-6,5x95 Part number 3029800311 3029300311
R i vets
S peci a l screw s
S torm w a shers
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For xing metal proles to timber substructure For xing metal proles to aluminium substructure 3 mm and steel substructure 2 mm FEATURES A2 stainless steel With flat head Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm 50 80
PU
Part number
250 200
3123083311 3124083311
92
Acces sor ie s
Inst al l at i on to ol s
mm
Length mm 19 25 25 25
PU
Part number FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
500
3120111311
mm
Length mm 19 19 25
PU
Part number FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drive ....................................................... hexagon A/F 3/8 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
93
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
without sealing washer 6.3 6.3 Sealing washer E14, 14 mm 6.3 Sealing washer E16, 16 mm 6.3
500
3120183311
S peci a l screw s
500 500
3122100319 3020100311
S torm w a shers
APPLICATION RANGE For fixing metal proles and timber to steel substructure For xing metal proles and timber to aluminium substructure FEATURES A2 stainless steel TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
S torm w a shers
Length mm 19 25 35 64 90
Price / Order description 100 pcs. JZ3-S-6,3x19 JZ3-S-6,3x25 JZ3-S-6,3x35 JZ3-S-6,3x64 JZ3-S-6,3x90
R i vets
S peci a l screw s
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For fixing metal proles and facade panels to steel substructure For xing metal proles and facade panels to aluminium substructure FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
mm
Length mm 19 19 19
PU
Part number
without sealing washer 6.3 Sealing washer E14, 14 mm 6.3 Sealing washer E16, 16 mm 6.3
94
Acces sor ie s
Inst al l at i on to ol s
APPLICATION RANGE Fixing of proled steel sheet to steel substructures under high static stress Fixing of steel / aluminium proled sheets to aluminium substructures mm Length mm PU Price / Order description 100 pcs. JZ3-8x25-E22 JZ3-8x32-E22 JZ3-8x38-E22 JZ3-8x64-E22 JZ3-8x100-E22 JZ3-8x125-E22 JZ3-8x150-E22 JZ3-8x200-E22 Part number FEATURES A2 stainless steel Stainless steel sealing washer Pre-assembled sealing washer APPROVAL ETA-10/0200 TECHNICAL DATA Drive .......................................................... hexagon A/F13 CROSS REFERENCE Accessories ............................................ page 191 Special screwgun DAM5 .......................... page 180
APPLICATION RANGE Concealed fixing of agraffes to HPL facade panels (HPL = High Pressure Laminate) Concealed xing of anchor rails to substructures FEATURES Truss head A4 stainless steel TECHNICAL DATA Drive ............................................ Hexalobular / TORX T30 Hole depth ......................................................... 5.5 mm Hole depth ......................................................... 7.5 mm Hole depth ....................................................... 10.5 mm NOTE Max. installation torque 4Nm CROSS REFERENCE Accessories ............................................ page 191
* Hole diameter and installation depth depend on the appearance of the facade panel. Consultation with the EJOT service team required.
95
Acces sor ie s
Inst al l at i on to ol s
* * *
* * *
mm
Length mm
Drill hole mm
clamping thickness mm
PU
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
96
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
A. Svinnset
NEW OPERA, OSLO, NORWAY Supplied by EJOT: EJOT SUPER-SAPHIR Self-drilling screw JT3, JA3 Self-tapping screw
mm 5.0
Length mm 35
PU 500
Part number 2010464609 FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) TECHNICAL DATA Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 191
APPLICATION RANGE For direct fastening to timber substructure mm 5.0 Length mm 35 PU 500 Price / Order description 100 pcs. SH3-5,0x35 Part number 3195035330 FEATURES A2 stainless steel TECHNICAL DATA Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 191
97
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S torm w a shers
APPLICATION RANGE Fastening of wood cladding to timber substructure FEATURES A2 stainless steel Countersunk head TECHNICAL DATA Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 191 mm 4.0 Length mm 45 PU 500 Price / Order description 100 pcs. SH3-S-4,0x45 Part number 3194045349
R i vets
S peci a l screw s
APPLICATION RANGE Fastening of wood cladding to timber substructure FEATURES A2 stainless steel Countersunk head TECHNICAL DATA Drive ............................................ Hexalobular / TORX T20 CROSS REFERENCE Accessories ............................................ page 191 mm 4.5 Length mm 55 PU 500 Price / Order description 100 pcs. SH3-S-4,5x55 Part number 3194555349
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE Fastening of wood cladding to timber substructure FEATURES A2 stainless steel Countersunk head TECHNICAL DATA Drive ............................................ Hexalobular / TORX T25 CROSS REFERENCE Accessories ............................................ page 191 mm 5.0 5.0 Length mm 60 70 PU 500 500 Price / Order description 100 pcs. SH3-S-5,0x60 SH3-S-5,0x70 Part number 3195060349 3195070349
98
Acces sor ie s
Inst al l at i on to ol s
mm
Length mm
Clamp thickness mm 9 15 7 13
PU
Part number
APPLICATION RANGE Aluminium screw boss Thin-walled aluminium components mm Length mm Clamp thickness mm 19 16 PU Price / Order description 100 pcs. DG-50x25-Z DG-50x25-Z-E11 Part number FEATURES A4 stainless steel Stainless steel sealing washer For thread geometries optimised for aluminium TECHNICAL DATA Thread ................................................................... DG 50 Drive .............................................hexalobular / TORX T25
1,000
2571468340
APPLICATION RANGE Clamped joint in a u-shaped prole FEATURES A2 stainless steel For thread geometries optimised for aluminium mm 5.5 Length mm 42 Clamp thickness mm 35 PU Price / Order description 100 pcs. DG-55x42-C Part number 2590228320 TECHNICAL DATA Drive ...................................................... PH2 cross-recess
99
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
1,000
2590168340
P ipe f lashings
R i vets
without sealing washer 4.0 13 4.0 19 with sealing washer E11 4.0 13 4.0 19
S peci a l screw s
FEATURES A4 stainless steel Stainless steel sealing washer For thread geometries optimised for aluminium
S torm w a shers
S torm w a shers
APPLICATION RANGE Fastening of metal ttings to aluminium FEATURES A2 stainless steel For thread geometries optimised for aluminium TECHNICAL DATA Drilling capacity ............................................. max. 2,5 mm Head diameter....................................................... 7,5 mm Thread ................................................................... DG 40 Drive ...................................................... PH2 cross-recess
S peci a l screw s
mm 4.0 4.0
Length mm 16 25
Clamp thickness mm 10 19
PU 1,000 1,000
Price / Order description 100 pcs. Self-drilling screw DG-40x16 Self-drilling screw DG-40x25
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE Direct fastening of T-bars to aluminium post and rail designs Fastening of additional proles, e.g. connecting proles, expansion joints etc. FEATURES A2 stainless steel For thread geometries optimised for aluminium TECHNICAL DATA Drilling capacity ................................................ bis 2,5 mm Thread ................................................................... DG 50 Drive .............................................hexalobular / TORX T25
mm 5.0
Length mm 16
Clamp thickness mm 8
PU 1,000
100
Acces sor ie s
Inst al l at i on to ol s
rr-fotoreporter
R i vets
101
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Rivet
S el f-dri l l i ng screw s
APPLICATION RANGE For side lap stitching of proled sheet FEATURES Rivet body made of aluminium (Al) Mandrel made of stainless steel (E) Captive locked APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172 mm 4.0 4.8 4.8 4.8 Length mm 10.0 10.0 15.0 25.0 Drill Clampinghole range mm mm 4.1 2.0 - 6.0 5.1 0.5 - 6.5 5.1 4.5 - 11.0 5.1 11.0 - 19.5 PU 1,000 1,000 1,000 1,000 Price / Order description 100 pcs. Blind rivet AL/E-4,0x10,0 Blind rivet AL/E-4,8x10,0 Blind rivet AL/E-4,8x15,0 Blind rivet AL/E-4,8x25,0 Part number 9351115000 9351121000 9351124000 9351130000
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For side lap stitching of proled sheet FEATURES Rivet body made of aluminium (Al) Zinc-plated steel (V) mandrel Captive locked APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172 mm 4.8 4.8 Length mm 10.0 15.0 Drill hole mm 5.1 5.1 Clampingrange mm PU Price / Order description 100 pcs. Blind rivet AL/V-4,8x10,0 Blind rivet AL/V-4,8x15,0 Part number 9350120001 9351122000
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE For xing steel and aluminium substructures To form oating points on aluminium substructure FEATURES Rivet body made of aluminium (Al) Mandrel made of stainless steel (E) Captive locked APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172
Inst al l at i on to ol s
102
Acces sor ie s
Clampingrange mm 1.0 - 3.5 3.5 - 5.0 4.0 - 6.5 6.5 - 8.0 8.0 - 9.5 8.5 - 11.0
Price /100 Order description pcs. Blind rivet K14-AL/E-5,0x8,0 Blind rivet K14-AL/E-5,0x10 Blind rivet K14-AL/E-5,0x12,0 Blind rivet K14-AL/E-5,0x14,0 Blind rivet K14-AL/E-5,0x16,0 Blind rivet K14-AL/E-5,0x18,0
Rivet
APPLICATION RANGE For side lap stitching of proled sheet mm 4.8 4.8 4.8 4.8 4.8 4.8 4.8 Length mm 8.3 10.0 11.5 13.0 14.5 18.0 22.0 Drill Clampinghole range mm mm 4.9 0.5 - 3.2 4.9 3.2 - 4.8 4.9 4.8 - 6.4 4.9 6.4 - 7.9 4.9 7.9 - 9.5 4.9 9.5 - 12.7 4.9 12.7 - 15.9 PU 1,000 1,000 1,000 1,000 1,000 1,000 1,000 Price /100 Order description pcs. Closed-end rivet AL/E-4,8x8,3 Closed-end rivet AL/E-4,8x10 Closed-end rivet AL/E-4,8x11,5 Closed-end rivet AL/E-4,8x13,0 Closed-end rivet AL/E-4,8x14,5 Closed end rivet AL/E-4,8x18,0 Closed-end rivet AL/E-4,8x22,0 Part number 9350102001 9350108001 9350103001 9350106001 9350109001 9350110001 9350107001 FEATURES Rivet body made of aluminium (Al) Mandrel made of stainless steel (E) Captive locked APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172
APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172
103
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Clampingrange mm - 3.2 3.2 -4.8 4.8 - 6.4 6.4 - 7.9 7.9 - 9.5
Price /100 Order description pcs. Closed-end rivet AL/V-4,8x8,3 Closed-end rivet AL/V-4,8x10,0 Becherblindniet AL/V-4,8x11,5 Closed-end rivet AL/V-4,8x13,0 Closed-end rivet AL/V-4,8x14,5
FEATURES Rivet body made of aluminium (Al) Zinc-plated steel (V) mandrel Captive locked
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Rivet
S el f-dri l l i ng screw s
APPLICATION RANGE For side lap stitching of metal and proled plastic sheets FEATURES Body made of aluminium (Al) with neoprene sealing Mandrel made of aluminium (Al) Captive locked APPROVAL Z-14.1-4 CROSS REFERENCE Electric riveting tool ................................. page 172
S torm w a shers
R i vets
Price / Drill ClampingPU 100 hole range mm pcs. mm 5.4 1.3 - 4.8 1,000 5.4 1.5 - 6.4 1,000 5.4 4.8 - 9.5 1,000 5.4 7.9 - 12.7 500 5.4 11.1 - 15.9 500 5.4 14.3 - 19.1 500
Order description Bulbtite rivet -5,2x17,5 Bulbtite rivet-5,2x19,1 Bulbtite rivet-5,2x22,2 Bulbtite rivet-5,2x25,4 Bulbtite rivet-5,2x28,6 Bulbtite rivet-5,2x31,8
S peci a l screw s
P ipe f lashings
APPLICATION RANGE For use in metal, masonry and concrete FEATURES Rivet body made of aluminium (Al) Mandrel made of stainless steel (E) Drill hole mm 4.8 15.3 5 4.8 25.4 5 4.8 35.0 5 Other designs on request. mm Length mm PU 1,000 1,000 500 Price / Order description 100 pcs. Drive rivet AL/E-4.8x15.3 Drive rivet AL/E-4.8x25.4 Drive rivet AL/E-4.8x35.0 Part number 8551600130 8552600130 8553600130
104
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For fastening elevated solar and photovoltaic installations FEATURES A2 stainless steel APPROVAL Z-14.4-532 ADVANTAGES: Short delivery times Flexibility in case of special requests Expert advise High product quality through strict quality control Quick retrofitting on existing roofs No additional holes in the roof cladding Use of proven sealing systems No special assembly tools necessary Extremely secure attachment due to direct fastening into the substructure Building authorities approved fastening system Project related structural pre-analysis, free of charge
Drive A/F 5
Set screw DIN 913 M10 x Lg A2 Lock nut DIN 985 M10 Plain washer M10 Hex nut M10 Sealing washer E16 EJOT ORKAN storm washer FZD A2 sealing washer EJOT Self-tapping screw JA3 - 8,0 x L EJOT Self-tapping screw JZ3 - 8,0 x L
105
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
L
Width Breite
Lg
S peci a l screw s
S torm w a shers
E16
Version For substructure Material Drive Threaded part Sealing systems D [mm]
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
JZ3-SBsteel A2 stainless steel A/F 5 M10 x 50 M10 x 70 Sealing washer E16/2 + Storm Washer Sealing washer FZD A2 8.0 64 80 100 125 150 160 200 240 280
JA3-SBwood A2 stainless steel A/F 5 M10 x 50 M10 x 70 Sealing washer E16/2 + Storm Washer Sealing washer FZD A2 8.0 80 100 130 150 180 200
NOTE For more information please see our brochure EJOT Solar Fastening Systems, which you can also download at our webpage www.ejot.com The EJOT service team will gladly assist you. Phone: +49 2752 908-0
TABLE OF CONTENTS (EXCERPT) EJOT Solar Fastening System EJOT Solar Fastening System concrete EJOT Flat Roof Solar Fastening System EJOT Solar Fastening System FD
106
Acces sor ie s
Inst al l at i on to ol s
Stift Pin
el le k g in An W
Fastening Systems for Solar Installations EJOT Solar Fastening System JZ3-SBwith JZ3 thread for steel substrate TYPE I
S el f-dri l l i ng screw s
TYPE II
APPROVAL Z-14.4-532 SEAL TYPE I Sealing washer E16/2 + ORKAN storm washer APPLICATION RANGE TYPE I Trapezoidal prole (metal) Corrugated prole sheet (metal) Sandwich panel SEAL TYPE II Pre-assembled FZD sealing washer + A2 stainless steel spreader washer APPLICATION RANGE TYPE II Corrugated prole sheet Fibre cement proles
EJOT Solar Fastening System JA3-SBwith JA3 thread for timber substructure TYPE I
FEATURES A2 stainless steel APPROVAL Z-14.4-532 TYPE II SEAL TYPE I Sealing washer E16/2 + ORKAN storm washer APPLICATION RANGE TYPE I Trapezoidal prole (metal) Corrugated prole sheet (metal) Sandwich panel SEAL TYPE II Pre-assembled FZD sealing washer + A2 stainless steel spreader washer APPLICATION RANGE TYPE II Corrugated prole sheet Fibre cement proles
107
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
108
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Colexon Energy AG
WORLD'S LARGEST ROOF SOLAR POWER STATION ON PIG FATTENING STATION, GERMANY Supplied by EJOT: EJOT Solar Fastening System
Direct Fastening
APPLICATION RANGE Fastening of proled steel sheets onto steel substrate 6 mm ADVANTAGES: Ensures ergonomic working to reduce down-time caused by health problems Fatigue-free installation in upright position Quick installation sequence APPROVAL Z-14.1-4 ETA-08/0040 FEATURES Automatic bolt, cartridge and piston feed Bolt collator on the tool TECHNICAL DATA Machine length .................................................. 1000 mm Contact pressure ...................................................... 20 kg Setting energy .......................................................... 520 J Calibre .................................................................. 14 mm Cartridge ..............................................................10 shots INCLUDED IN DELIVERY 1 shot ring tool 1 oil spray 35 ml 1 protective goggles 1 cleaning set 1 operating manual 1 transport box
Weight kg 9
Accessories Order description Power damping element Barrel Cleaning set Thrust piston Protective goggles Spray oil can 35 ml Compressed ring Telescopic ring Intermediate ring Price / Part number pcs. 9600132802 9600110954 9600074000 9600110957 9600074020 9600310080 9600132801 9600110948 9600132805
109
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Direct Fastening
S el f-dri l l i ng screw s
S torm w a shers
APPLICATION RANGE Fastening of proled steel sheets onto steel substrate 6 mm For fastening cassettes onto steel columns 60 mm ADVANTAGES: Fast installation sequence through automated repetition Compact and lightweight design Quick release fastening system Easy cleaning Stability system for secure storage APPROVAL Z-14.1-4 ETA-08/0040 FEATURES Automatic bolt, cartridge and piston feed Bolt collator on the tool TECHNICAL DATA Weight incl. collator ................................................ 4,23 kg Setting energy .......................................................... 520 J Collator ............................................ 10 bolts/10 cartridges Cartridges ...................................... 6,3/16 (black, red, blue) Dimensions ......................H 277 mm / L 363 mm / W 77 mm Accessories INCLUDED IN DELIVERY 1 shot ring tool 1 oil spray 35 ml 1 protective goggles 1 cleaning set 1 operating manual 1 transport box Order description Barrel Cleaning set Thrust piston Protective goggles Spray oil can 35 ml Compressed ring Price / Part number pcs. 9600014139 74000 9600014137 9600011117 9600310080 9600014136 Order description P 560 shot ring tool Weight kg 4.23 Price / Part number pcs. 9600013891
110
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
Direct Fastening
Cartridges 6,3/16
blue, red, black
APPROVAL ETA-08/0040 Order description Blue cartridge: strong Red cartridge: very strong Black cartridge: strongest Price / Part number 100 pcs. 9600003123 9600003122 9600003121
9600003176
APPROVAL ETA-08/0040
APPLICATION RANGE For high strength substructures (e.g. S355 or higher) APPROVAL ETA-08/0040
111
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE For shot firing tool P 525 L For shot firing tool P 560
S el f-dri l l i ng screw s
Scaffolding fasteners
S el f-dri l l i ng screw s
R i vets
S peci a l screw s
S torm w a shers
Characteristic tensile force N R.k [kN] (at right angles with assembly level) Scaffolding anchor JZ 3 - GU - 6,3 x L drill hole (mm) Characteristic pull-out load ** (kN) Thickness of the steel substrate tII in mm from S 235 Jxx (St 37) 2.0 5.3 3.6 3.0 5.3 6.0 4.0 5.3 8.8 5.0 5.5 11.6 6.0 5.5 13.4 7.0 5.7 13.4
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Scaffolding anchor JA 3 - GU - 6,5 x L drill hole (mm) Characteristic pull-out load ** (kN)
30 4.5 1.5
Installation depth into the timber substructure in mm 50 60 75 4.5 2.5 4.5 3.0 4.5 3.7
112
Acces sor ie s
Inst al l at i on to ol s
* Based on the approval of the screws ETA-10/0200 addendum 44 and 45 ** Based on the approval of the screws ETA-10/0200
Scaffolding fasteners
APPLICATION RANGE For installation into wood FEATURES A2 stainless steel TECHNICAL DATA Drive .............................................hexalobular / TORX T30 Sealing washer ......................................................... E16/2 High thread ................................................................ M10 CROSS REFERENCE Accessories ............................................ page 191
PU 50 50
6.5 6.5
32 64
JA3-GT-6,5x32-E16/2 JA3-GT-6,5x64-E16/2
APPLICATION RANGE For installation into steel 2 mm For aluminium substructures 3 mm FEATURES A2 stainless steel mm 6.3 6.3 Length of self-tapping screw [mm] 25 64 Price / Order description 100 pcs. JZ3-GT-6,3x25-E16/2 JZ3-GT-6,3x64-E16/2 TECHNICAL DATA Drive .............................................hexalobular / TORX T30 Sealing washer ......................................................... E16/2 High thread ................................................................ M10 CROSS REFERENCE Accessories ............................................ page 191
50 50
9411211311 9411811311
PU 50 50
Price / Order description 100 pcs. Eyebolt M10-25 stainless steel Eyebolt M10-25 steel
113
Acces sor ie s
FEATURES Zinc-plated forged steel (as per DIN 582) A2 stainless steel
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
PU
Part number
P ipe f lashings
R i vets
S peci a l screw s
mm
S torm w a shers
S el f-dri l l i ng screw s
Scaffolding fasteners
S el f-dri l l i ng screw s
APPLICATION RANGE For installation into wood FEATURES A2 stainless steel TECHNICAL DATA Drive ........................................................ hexagon A/F 3/8 Sealing washer ......................................................... E16/2 Threaded sleeve ................................................... M14x1,5 NOTE consisting of EJOT GU threaded sleeve and EJOT JA3 self-tapping screw CROSS REFERENCE Accessories ............................................ page 191 Self-tapping screw JA3-6,5 ...................... page 78
S peci a l screw s
S torm w a shers
Length of self-tapping screw [mm] 75 90 100 115 125 150 175 200
PU 50 50 50 50 50 50 50 50
Price / Order description 100 pcs. JA3-GU-6,5x55-E16/2 JA3-GU-6,5x70-E16/2 JA3-GU-6,5x80-E16/2 JA3-GU-6,5x95-E16/2 JA3-GU-6,5x105-E16/2 JA3-GU-6,5x130-E16/2 JA3-GU-6,5x155-E16/2 JA3-GU-6,5x180-E16/2
Part number 9403611311 9403911311 9404011311 9404111311 9404211311 9404411311 9404611311 9404711311
R i vets
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For installation into steel 2 mm For installation into aluminium 3 mm FEATURES Threaded sleeve and self-tapping screw made of A2 stainless steel TECHNICAL DATA Drive ........................................................ hexagon A/F 3/8 Sealing washer ......................................................... E16/2 Threaded sleeve ................................................... M14x1,5 NOTE Consisting of EJOT GU threaded sleeve and EJOT JZ3 self-tapping screw Accessories ............................................ page 191 Self-tapping screw JZ3-6,3 ...................... page 80
mm 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3
Effective length scaffolding anchor [mm] 15 30 45 70 80 95 105 130 155 180 210
Length of self-tapping screw [mm] 38 50 64 90 100 115 125 150 175 200 230
PU 50 50 50 50 50 50 50 50 50 50 50
Price / Order description 100 pcs. JZ3-GU-6,3x15-E16/2 JZ3-GU-6,3x30-E16/2 JZ3-GU-6,3x45-E16/2 JZ3-GU-6,3x70-E16/2 JZ3-GU-6,3x80-E16/2 JZ3-GU-6,3x95-E16/2 JZ3-GU-6,3x105-E16/2 JZ3-GU-6,3x130-E16/2 JZ3-GU-6,3x155-E16/2 JZ3-GU-6,3x180-E16/2 JZ3-GU-6,3x210-E16/2
Part number 9401111311 9401211311 9401511311 9401911311 9402011311 9402111311 9402211311 9402411311 9402611311 9402811314 9402911314
114
Acces sor ie s
Inst al l at i on to ol s
Scaffolding fasteners
PU 50
Sleeve length mm 18
PU 50
FEATURES A2 stainless steel TECHNICAL DATA ...................................................................... Wrench Size A/F 13 Threaded sleeve ................................................... M14x1,5 NOTE All EJOT self-tapping screws of the types JZ3 6,3 and JA3 6,5 can be combined to a GU universal scaffolding anchor. Effective length of universal scaffolding anchor GU + 20 mm = length of screw required.
115
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Pipe flashings
S el f-dri l l i ng screw s
easily identiable pipe/cable bundle size absorbing of the load through two exible pleats exible, conical sleeve
S torm w a shers
R i vets
S peci a l screw s
low prole
116
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Pipe flashings
935 x 970 - up to 45 - up to 30 - up to 15 - up to 6
310 -
70/10 -
1 -
DC110 -
8270004704 -
NOTE FOR SUBSEQUENT WATERPROOFING See processing guidelines for Dektite Retrot
3. Apply sealant
117
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
Base mm
Roof pitch
Cartridge capacity ml
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Pipe flashings
S el f-dri l l i ng screw s
S peci a l screw s
S torm w a shers
P ipe f lashings
For pipe mm 0 - 35 5 - 55 5 - 120 110 - 170 160 - 220 160 - 300 290 - 440
Base mm 99 x 99 137 x 137 218 x 218 284 x 284 365 x 365 453 x 453 581 x 581
Screws pcs. 8 8 16 20 28 32 40
PU 1 1 1 1 1 1 1
Price Order / description pcs. DFE 0-35 DFE 5-55 DFE 5-120 DFE 110-170 DFE 160-220 DFE 160-300 DFE 290-440
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
3. Apply sealant
118
Acces sor ie s
Inst al l at i on to ol s
Pipe flashings
119
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
For pipe mm 0 - 35 5 - 55 5 - 120 110 - 170 160 - 220 160 - 300 290 - 440
Base mm 99 x 99 137 x 137 218 x 218 284 x 284 365 x 365 453 x 453 581 x 581
Roof pitch 0 - 60 0 - 35 0 - 35 0 - 35 0 - 35 0 - 35 0 - 35
Screws pcs. 8 8 16 20 28 32 40
PU 1 1 1 1 1 1 1
Price / Order description pcs. DFE 0-35 EZ DFE 5-55 EZ DFE 5-120 EZ DFE 110-170 EZ DFE 160-220 EZ DFE 160-300 EZ DFE 290-440 EZ
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Pipe flashings
S el f-dri l l i ng screw s
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
3. Mark the outline of the soaker on the roof then remove it. Mark a lap allowance of 30mm (inside the original mark)
4. Cut out the roof inside of the marked 30mm area. Trim sharp edges. Timber supports must be installed to support the roof where ribs have been removed.
Acces sor ie s
Inst al l at i on to ol s
6. Fix to the middle front and middle back of the Dektite soaker and x progressively towards the edge
7. Use provided metal strips to seal overlapping ends. Trim excess sides
120
Pipe flashings
PU 1 1 1 1
121
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
2. Place the Dektite Retrot raound the pipe and engage metal teeth in opposing pockets starting at the top
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Pipe flashings
S el f-dri l l i ng screw s
S peci a l screw s
S torm w a shers
R i vets
Length m
Width mm
Cartridge capacity ml
PU 1 1
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
2. Do not mark the sealing line more than 75 mm above the purlin
4. Trim every side of the Dektite Strip Flash. Allow 200 - 300 mm for overlap
5. Fixing along the upper edge without stretching of the Dektite Strip Flash
6. Press Dektite Strip Flash to the proled sheet by hand. Do not use tools!
7. Apply sealant
Acces sor ie s
Inst al l at i on to ol s
9. Stretch the corners of the overlapping upper part of the Dektite Strip Flash and push down. Attach the uper corner
10. Remove excess Dektite Strip Flash. Overlap needs to be done thoroughly. Also apply sealing compound under the overlap on the edges
12. Apply sealing compound acroos the edges and form a ridge in order to slow down the water ow
122
APPLICATION RANGE A reliable seal between pipe and pipe ashing INSTALLATION NOTE Pierce the marking for the clamp or cable tie at the joint, pull through, place around the Dektite Retrot and close.
PU 1 1 1 1 1 1
Price / pcs. Order description Hose clamp 40-60 Hose clamp 60-80 Hose clamp 70-90 Hose clamp 90-110 Hose clamp 110-130 Hose clamp 130-150
APPLICATION RANGE A reliable seal between pipe and pipe ashing FEATURES For diameters from 150 mm onwards ORDER NOTE Universal hose clamp consisting of tightener and universal cable tie. Length of universal cable tie pipe circumference + 50 mm Width mm 7 PU 1 1 Price Order description Part number 8200077300 8200076300 INSTALLING THE CABLE TIE Tip back the hinged screw in the tightener, insert one end of the universal cable tie through the clamp lock and twist about 15 mm. Place universal fastener strap around Dektite, insert through the tightener and tighten by hand. Hinge the screw inwards and tighten as far as possible with a screwdriver.
123
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S torm w a shers
S peci a l screw s
Contents mm 80 310
PU 1 1
R i vets
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
124
Acces sor ie s
Inst al l at i on to ol s
125
Acces sor ie s
Inst al l at i on to ol s
S el f-dri l l i ng screw s
DABO SELF-DRILLING SCREWS BY EJOT Very high corrosion protection due to high-quality Climadur* coating R Alternative corrosion resistance stainless steel "E" Resistant to imposed loads Screws and plates available collated or belt-fed No loosening EJOT STRESS PLATES Metal plates, made of alu-zinc coated steel Plastic plates made of high-grade polyamide Geometry optimised for roofing membranes Screws and plates available collated or belt-fed FEATURES Variable length combinations up to 400 mm insulation thickness Minimal thermal bridging Approved flat roofing fasteners acc. to ETAG 006 New EJOT complete product range with solutions for almost all applications Approved corrosion protection acc. to strictest regulations Economical processing with EJOT ECOset installation tool EJOT AERATED CONCRETE SCREWS Secure fastening of roofing membrane and thermal insulation to aerated concrete Flat roofing fastener approved in the ETA-07/0013 No pre-drilling necessary Suitable for metal and plastic plates Telescope effect in combination with EJOT EcoTek stress plate Corrosion resistant (A4 stainless steel) EJOT CONCRETE SCREWS Case-hardened steel Very high corrosion protection due to high-quality Climadur* coating R Suitable for metal and plastic plates Telescope effect in combination with EJOT EcoTek stress plate Flat roofing fastener approved in the ETA-07/0013 Fastening without additional anchor *CLIMADUR High-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
Recommended at roong system combinations substructure sheet steel mineral bre thermal insulation polystyrene rigid foam without Insulation Others
1) 2)
wood
Others
S torm w a shers
FDD
FDD
FPS-E + HTV F
S peci a l screw s
Recommendation Denition of the design load only after pull-out tests by our service team As a rule, pull-out tests have to be arranged with our service team for all renovation cases
R i vets
SYSTEM OVERVIEW EJOT Fastening Systems sheet steel 0,75 mm S280GD1) X X X X X substructure timber T&G boarding2) concrete plywood C12/155) 3) BFU 100 OSB4) X X X X X X7) X7) X8) X8) X9)
6) P 3.3 / 5,0 EN 12602; 7) embedment depth 30 mm; 8) embedment depth 60 mm; 9) drill-hole diameter 10 mm, embedment depth 30 mm; 10) drill-hole diameter 8 mm, embedment depth 50 mm
screw
stress plate
Dabo TKR/E-4,8xL Dabo TKR/E-4,8xL Dabo TKR/E-4,8xL Dabo A/F8R(T)-4,8xL Dabo A/F8R(T)-4,8xL FBS-R-6,3xL FBS-R-6,3xL FPS-E-8,0xL FPS-E-8,0xL FDD-50xL
HTK HTV 82/40 TK HTV 82/40 F HTV 82/40 HTV 82/40 F EcoTek 50 HTV 82/40 F EcoTek 50
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
X10)
1) S280GD-EN 10326, thickness tmin = 0,75 mm; 2) T&G boarding: EN 338/C24, thickness 25 mm; 3) plywood: EN 636: 2003-11; BFU 100: DIN 68705-3, thickness 21 mm; 4) OSB EN 300, EN 13986:2002-09; thickness 18 mm; 5) C 12/15 EN 206;
126
Acces sor ie s
Inst al l at i on to ol s
NOTE Other combinations of the at roong system componentes are also possible! Ask our service team!
EJOT aerated concrete screw FPS-E-8,0 Self-drilling screw EJOT Dabo TKE-4,8 EJOT stress plate HTK 50 Self-drilling screw EJOT Dabo TKR-4,8 Self-drilling screw EJOT Dabo A/F8 RT-4,8 Self-drilling screw EJOT Dabo A/F 8 R-4,8
EJOT stress plate HTV 82/40 TK EJOT stress plate HTV 82/40 EJOT stress plate HTV 82/40 F EJOT stress plate HTV 40 RU EJOT stress plate EcoTek 50
127
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
J2
APPLICATION RANGE For fixing roofing membrane to sheet steel substructures 0,75 mm 1 mm In combination with EJOT stress plate HTV 82/40 For timber substructure FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) APPROVAL ETA-07/0013 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ............................................................ hexagon A/F8 Length determination for: sheet steel: ............................ insulation thickness +20 mm timber: ................................... insulation thickness +30 mm * Min. lengths CROSS REFERENCE HTV stress plate 82/40............................. page 134 ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
S peci a l screw s
S torm w a shers
R i vets
mm bulk packed 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8
Length mm 80 100 120 140 160 180 200 220 240 260
PU
Price / Order description 100 pcs. A/F8R-4,8x80 A/F8R-4,8x100 A/F8R-4,8x120 A/F8R-4,8x140 A/F8R-4,8x160 A/F8R-4,8x180 A/F8R-4,8x200 A/F8R-4,8x220 A/F8R-4,8x240 A/F8R-4,8x260
Part number
128
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
250 250 250 200 200 200 200 200 150 250
3487100629 3487300629 3487500629 3487700629 3487900629 3488100629 3488300629 3488400629 3488600629 3488800629
Flat roofing Self-drilling screws Climadur coated EJOT Dabo Screw A/F 8 RT-4,8
with A/F8 hexagonal head and supporting thread
S el f-dri l l i ng screw s
J2
FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) mm bulk packed 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 belted 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 Length mm 80 100 120 140 160 180 200 220 240 260 80 100 120 140 160 180 200 220 240 260 PU Price / Order description 100 pcs. A/F8RT-4,8x80 A/F8RT-4,8x100 A/F8RT-4,8x120 A/F8RT-4,8x140 A/F8RT-4,8x160 A/F8RT-4,8x180 A/F8RT-4,8x200 A/F8RT-4,8x220 A/F8RT-4,8x240 A/F8RT-4,8x260 A/F8RT-4,8x80-belted A/F8RT-4,8x100-belted SW8RT-4,8x120-belted A/F8RT-4,8x140-belted A/F8RT-4,8x160-belted A/F8RT-4,8x180-belted A/F8RT-4,8x200-belted A/F8RT-4,8x220-belted A/F8RT-4,8x240-belted A/F8RT-4,8x260-belted Part number APPROVAL ETA-07/0013 TECHNICAL DATA Drilling capacity tI + tII ............................................ 2,0 mm Drive ............................................................ hexagon A/F8 Length determination for: sheet steel: ............................ insulation thickness +20 mm timber: ................................... insulation thickness +30 mm * Min. lengths CROSS REFERENCE HTV stress plate 82/40............................. page 134 ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
250 250 250 200 200 200 200 200 150 250 750 750 750 750 750 750 750 750 750 750
3477100629 3477300629 3477500629 3477700629 3477900629 3478100629 3478300629 3478400629 3478600629 3478800629 3477101629 3477301629 3477501629 3477701629 3477901629 3478101629 3478301629 3478401629 3478601629 3478801629
129
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
APPLICATION RANGE For fixing roofing membrane to sheet steel substructures 0,75 mm 1 mm Support thread designed to engage in the stress plate for resistance to imposed loads In combination with EJOT stress plate HTV 82/40 For timber substructure
S torm w a shers
S peci a l screw s
APPLICATION RANGE For fixing roofing membrane to sheet steel substructures 0,75 mm 1 mm For timber substructure In combination with EJOT HTK 50 stress plate In combination with EJOT stress plate HTV 82/40 F In combination with EJOT stress plate HTV 82/40 F FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Can be delivered belted for EJOT ECOset installation tool or pre-assembled with EJOT stress plates HTK for EJOT ECOset HTK installation tool APPROVAL ETA-07/0013 TECHNICAL DATA Drilling capacity tI + tII ............................................ 2,0 mm Drive ......................................................... H2 cross recess Length determination for: sheet steel: ............................ insulation thickness +20 mm timber: ................................... insulation thickness +30 mm * Min. lengths CROSS REFERENCE Stress plate HTK 50 ................................. Stress plate HTV 82/40 TK ........................ Stress plate HTV 82/40 F.......................... ECOset installation tool............................. ECOset L installation tool .......................... ECOset HTK installation tool .....................
R i vets
S torm w a shers
mm bulk packed 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8
Length mm 35 50 60 70 80 90 100 110 120 130 140 150 160 170 180 200 220 240 260 280 300
PU
Price / Order description 100 pcs. TKR-4,8x35 TKR-4,8x50 TKR-4,8x60 TKR-4,8x70 TKR-4,8x80 TKR-4,8x90 TKR-4,8x100 TKR-4,8x110 TKR-4,8x120 TKR-4,8x130 TKR-4,8x140 TKR-4,8x150 TKR-4,8x160 TKR-4,8x170 TKR-4,8x180 TKR-4,8x200 TKR-4,8x220 TKR-4,8x240 TKR-4,8x260 TKR-4,8x280 TKR-4,8x300
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
page 136 page 134 page 135 page 173 page 174 page 175
500 500 500 500 500 250 250 250 250 250 200 200 200 200 200 200 200 200 250 250 250
3496700629 3496800629 3496900629 3497000629 3497100629 3497200629 3497300629 3497400629 3497500629 3497600629 3497700629 3497800629 3497900629 3498000629 3498100629 3498300629 3498400629 3498600629 3498800629 3498900629 3499000629
P ipe f lashings
Order information: Further lengths upon request. Also available belted for ECOset or pre-assembled with HTK for ECOset HTK.
130
Acces sor ie s
Inst al l at i on to ol s
Flat roofing Self-drilling screws Climadur coated EJOT Dabo Screw TKR-3-4,8
with bugle head
S el f-dri l l i ng screw s
APPLICATION RANGE For fixing roofing membrane to sheet steel substructure 1 mm 3 mm In combination with EJOT HTK 50 stress plate In combination with EJOT stress plate HTV 82/40 F In combination with EJOT stress plate HTV 82/40 F FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) Can be delivered belted for EJOT ECOset installation tool or pre-assembled with EJOT stress plates HTK for EJOT ECOset HTK installation tool TECHNICAL DATA Drilling capacity tI + tII .............................................3,0 mm Drive ......................................................... H2 cross recess CROSS REFERENCE Stress plate HTK 50 ................................. Stress plate HTV 82/40 TK ........................ Stress plate HTV 82/40 F.......................... ECOset installation tool............................. ECOset L installation tool .......................... ECOset HTK installation tool ......................
70 90 110
page 136 page 134 page 135 page 173 page 174 page 175
131
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
mm
Length mm
PU
Part number
R i vets
S peci a l screw s
S torm w a shers
S peci a l screw s
APPLICATION RANGE For xing roong membrane to single-ply sheet steel substructure 0,60 0,75 mm In combination with EJOT HTK 50 stress plate In combination with EJOT HTV 82/40 TK stress plate For timber substructure In combination with EJOT HTV 82/40 F stress plate In combination with EJOT stress plate HTV 40 RU FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) TECHNICAL DATA Drive ......................................................... H2 cross recess NOTE For thicker and/or two-ply sheet steel we recommend the use of the EJOT Dabo screw TKR-4,8. CROSS REFERENCE Stress plate HTK 50 ................................. Stress plate HTV 82/40 TK ........................ Stress plate HTV 82/40 F.......................... Stress plate HTV 40 RU ............................ ECOset installation tool............................. ECOset L installation tool .......................... ECOset HTK installation tool ...................... mm 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 Length mm 35 50 60 70 80 90 100 120 140 160 180 200 PU 500 500 500 500 500 250 250 250 200 200 200 200 Price / Order description 100 pcs. VHT-R-4,8x35 VHT-R-4,8x50 VHT-R-4,8x60 VHT-R-4,8x70 VHT-R-4,8x80 VHT-R-4,8x90 VHT-R-4,8x100 VHT-R-4,8x120 VHT-R-4,8x140 VHT-R-4,8x160 VHT-R-4,8x180 VHT-R-4,8x200 Part number 3496700609 3496800609 3496900609 3497000609 3497100609 3497200609 3497300609 3497500609 3497700609 3497900609 3498100609 3498300609
R i vets
S torm w a shers
132
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
page 136 page 134 page 135 page 135 page 173 page 174 page 175
Flat roofing Self-drilling screws A4 stainless steel EJOT Dabo Screw TKE-4,8
with bugle head
S el f-dri l l i ng screw s
APPLICATION RANGE To fix roofing membrane onto sheet steel substructures 0,75 mm 1 mm in combination with HTK 50 For timber substructures in combination with HTV 82/40 TK and HTV 82/40 F FEATURES A4 stainless steel with case-hardened drill point Can be delivered collated for EJOT ECOset installation tool or pre-assembled with HTK for EJOT ECOset HTK. APPROVAL ETA-07/0013 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Drive ......................................................... H2 cross recess CROSS REFERENCE Stress plate HTK 50 ................................. Stress plate HTV 82/40 TK ........................ Stress plate HTV 82/40 F.......................... ECOset installation tool............................. ECOset L installation tool .......................... ECOset HTK installation tool ......................
133
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
page 136 page 134 page 135 page 173 page 174 page 175
mm
Length mm
PU
Part number
R i vets
S peci a l screw s
S torm w a shers
S peci a l screw s
APPLICATION RANGE For securing roofing membrane onto substructure For renovations For installation with the EJOT ECOset L tool For combination with EJOT Dabo Schrauben SW 8 R, SW 8 RT For new buildings For manual installation FEATURES Alu-zinc coated steel APPROVAL ETA-07/0013 CROSS REFERENCE Dabo screws A/F 8 RT-4,8 ...................... Dabo screws A/F 8 R-4,8 ........................ ECOset installation tool............................. ECOset L installation tool ..........................
S torm w a shers
Width mm 40
Length mm 82
PU 1,000
R i vets
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For securing roofing membrane onto substructure For renovations For installation with the EJOT ECOset L tool For combination with EJOT Dabo screws TKR and TKE For new buildings For manual installation FEATURES Alu-zinc coated steel APPROVAL ETA-07/0013 CROSS REFERENCE Dabo screw TKR-4,8 .............................. Dabo screw TKE-4,8 .............................. ECOset installation tool............................. ECOset L installation tool ..........................
Width mm 40
Length mm 82
PU 1,000
Inst al l at i on to ol s
134
Acces sor ie s
Stress plates / flat roofing anchors Metal stress plates EJOT Stress plate HTV 82/40 F
for solid substructure
S el f-dri l l i ng screw s
Width mm 40
Length mm 82
PU 500
APPLICATION RANGE For securing roofing membrane onto substructure For fastening onto solid substructure in combination with all EJOT Dabo screws In combination with EJOT concrete screw FBS-R and gas concrete screw FPS-E FEATURES Alu-zinc coated steel APPROVAL ETA-07/0013 NOTE For combination with all EJOT Dabo screws CROSS REFERENCE Dabo screw SW 8 RT-4,8 ........................ Dabo screw SW 8 R-4,8 ......................... Dabo screw TKR-4,8 .............................. Dabo screw TKE-4,8 .............................. Concrete screw FBS-R ............................. Gas concrete screw FPS-E ........................
page 129 page 128 page 130 page 133 page 139 page 140
PU 1,000 500
FEATURES Alu-zinc coated steel APPROVAL ETA-07/0013 CROSS REFERENCE Dabo screw TKR-4,8 .............................. Dabo screw TKE-4,8 .............................. Concrete screw FBS-R ............................. Gas concrete screw FPS-E-8,0 ..................
135
Acces sor ie s
Inst al l at i on to ol s
APPLICATION RANGE For securing roofing membrane in combination with EJOT Dabo screws TKR and TKE For fastening pressure-proof insulation in combination with EJOT concrete screw FBS-R and gas concrete screw FPS-E
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE To secure roofing membrane For new buildings For special requirements of resistance to imposed loads For reduction of thermal bridges FEATURES Polyamide Telescope design, prevents screw head protrusion due to foot traffic even with soft insulating material APPROVAL ETA-07/0013 NOTE For combination with EJOT Dabo screws TKR and TKE CROSS REFERENCE Dabo screw TKR-4,8 .............................. Dabo screw TKE-4,8 ............................. ECOset installation tool............................. HSK-HTK manual installation tool ..............
S torm w a shers
plate mm 50 50 50 50 50 50
Price / Order description 100 pcs. HTK-50x35 HTK-50x55 HTK-50x95 HTK-50x115 HTK-50x145 HTK-50x185
R i vets
S peci a l screw s
P ipe f lashings
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE To secure roofing membrane For special requirements of resistance to imposed loads For reduction of thermal bridges FEATURES High-grade plastic material In combination for insulation material thicknesses up to 400 mm (FBS-R) and up to 490 mm (TKR) Telescope design, prevents screw head protrusion due to foot traffic even with soft insulating material APPROVAL ETA-07/0013 NOTE For combination with gas concrete screw FPS-E-8,0 and concrete screw FBS-R-6,3 CROSS REFERENCE Concrete screw FBS-R ............................. page 139 Gas concrete screw FPS-E ........................ page 140 plate mm 50 50 50 50 50 Effective shaft length L mm 25 55 95 155 215 PU 2,000 1,300 900 450 500 Price / Order description 100 pcs. EcoTek-50x35 EcoTek-50x65 EcoTek-50x105 EcoTek-50x165 EcoTek-50x225 Part number 8595035007 8595065007 8595105007 8595165007 8595225007
136
Acces sor ie s
Inst al l at i on to ol s
Stress plates / flat roofing anchors Plastic stress plates EJOT Stress plate HTK-M
collated
S el f-dri l l i ng screw s
Insulation Effective Screw Price / Order description thickness shaft length L length PU 100 pcs. mm mm mm with EJOT Dabo screw TKR 60 35 50 1,000 HTK-M/TKR-60-35/50 70 35 60 1,000 HTK-M/TKR-70-35/60 80 55 50 1,000 HTK-M/TKR-80-55/50 90 55 60 1,000 HTK-M/TKR-90-55/60 100 55 70 1,000 HTK-M/TKR-100-55/70 110 55 80 1,000 HTK-M/TKR-110-55/80 120 95 50 1,000 HTK-M/TKR-120-95/50 130 95 60 1,000 HTK-M/TKR-130-95/60 140 95 70 1,000 HTK-M/TKR-140-95/70 150 95 80 1,000 HTK-M/TKR-150-95/80 160 95 90 1,000 HTK-M/TKR-160-95/90 170 145 50 700 HTK-M/TKR-170-145/50 180 145 60 700 HTK-M/TKR-180-145/60 190 145 70 700 HTK-M/TKR-190-145/70 200 145 80 700 HTK-M/TKR-200-145/80 210 145 90 700 HTK-M/TKR-210-145/90 220 145 100 700 HTK-M/TKR-220-145/100 230 145 110 700 HTK-M/TKR-230-145/110 240 145 120 700 HTK-M/TKR-240-145/120 250 145 130 700 HTK-M/TKR-250-145/130 260 145 140 700 HTK-M/TKR-260-145/140 with EJOT Dabo screw TKE 60 35 50 1,000 HTK-M/TKE-60-35/50 70 35 60 1,000 HTK-M/TKE-70-35/60 80 55 50 1,000 HTK-M/TKE-80-55/50 100 55 70 1,000 HTK-M/TKE-100-55/70 110 55 80 1,000 HTK-M/TKE-110-55/80 120 95 50 1,000 HTK-M/TKE-120-95/50 130 95 60 1,000 HTK-M/TKE-130-95/60 140 95 70 1,000 HTK-M/TKE-140-95/70 150 95 80 1,000 HTK-M/TKE-150-95/80 160 95 90 1,000 HTK-M/TKE-160-95/90 170 145 50 700 HTK-M/TKE-170-145/50 180 145 60 700 HTK-M/TKE-180-145/60 190 145 70 700 HTK-M/TKE-190-145/70 200 145 80 700 HTK-M/TKE-200-145/80 210 145 90 700 HTK-M/TKE-210-145/90 220 145 100 700 HTK-M/TKE-220-145/100 230 145 120 700 HTK-M/TKE-230-145/110 240 145 120 700 HTK-M/TKE-240-145/120 250 145 140 700 HTK-M/TKE-250-145/130 260 145 140 700 HTK-M/TKE-260-145/140 Order information: For wooden substructures screws need to be chosen 10 mm longer
Part number
NOTE For combination with EJOT Dabo screws TKR and TKE drilling capacityt = 3 mm upon request! CROSS REFERENCE Dabo screw TKR-4,8 .............................. page 130 Dabo screw TKE-4,8 .............................. page 133 ECOset HTK installation tool ...................... page 175
3703506841 3703506941 3705506841 3705507041 3709506841 3709506941 3709507041 3709507241 3714506841 3714506941 3714507041 3714507241 -
137
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
3703596891 3703596991 3705596891 3705596991 3705597091 3705597191 3709596891 3709596991 3709597091 3709597191 3709597291 3714596891 3714596991 3714597091 3714597191 3714597291 3714597391 3714597491 3714597591 3714597691 3714597791
FEATURES TKR = Case-hardened steel, Climadur coated TKE = A4 stainless steel Polyamide Collated Telescope design, prevents screw head protrusion due to foot traffic even with soft insulating material Combinations for insulation thicknesses up to 400 mm on request *CLIMADUR High-grade coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) APPROVAL ETA-07/0013 TECHNICAL DATA Drilling capacity tI + tII .............................................2,0 mm Collator capacity ............................................................ 25
P ipe f lashings
R i vets
S peci a l screw s
APPLICATION RANGE To secure roofing membrane For new buildings For installation with the EJOT ECOset HTK tool For special requirements of resistance to imposed loads For reduction of thermal bridges For renovations For manual installation
S torm w a shers
S peci a l screw s
S torm w a shers
mm mm mm mm
R i vets
plate mm 50 50 50 50 50 50 50 50 50 50 50 50 50
Anchor length mm 55 75 95 115 135 155 175 200 220 240 260 280 300
Aerated concrete P 3.3 total height 5 25 45 65 85 105 125 150 170 190 210 230 250
Concrete B 15 total height 25 45 65 85 105 125 145 170 190 210 230 250 270
PU 200 200 200 200 200 200 200 100 100 100 100 100 100
Price / Order 100 pcs. description FDD-50x55 FDD-50x75 FDD-50x95 FDD-50x115 FDD-50x135 FDD-50x155 FDD-50x175 FDD-50x200 FDD-50x220 FDD-50x240 FDD-50x260 FDD-50x280 FDD-50x300
Part number 8520055280 8520075250 8520095220 8520115260 8520135210 8520155280 8520175230 8520200280 8520220250 8520240230 8520260260 8520280240 8520300270
NOTE AS spacer to prevent premature expansion of the anchor sleeve 1) Recommendation Denition of the design load only after pull-out tests by our service team 2) As a rule, pull-out tests have to be arranged with our service team for all renovation cases CROSS REFERENCE AS spacer ............................................... page 194
138
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Concrete- / aerated concrete screws Climadur coated EJOT Concrete screws FBS-R-6,3
S el f-dri l l i ng screw s
APPLICATION RANGE To secure roong membrane to concrete substructures In combination with EJOT stress plate EcoTek 50 In combination with EJOT stress plate HTV 82/40 F In combination with EJOT stress plate HTV 40 RU FEATURES Case-hardened steel Climadur coated high-quality coating to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997) APPROVAL ETA-07/0013 TECHNICAL DATA Drive .............................................hexalobular / TORX T30 Embedment depth ............................................... 30 mm Hole depth .......................................................... 45 mm NOTE Drill nominal diameter 5.0 mm CROSS REFERENCE Stress plate EcoTek 50 ............................. Stress plate HTV 82/40 F.......................... Stress plate HTV 40 RU ............................ Hammer drill bit SDS-plus ........................
Price / Order description 100 pcs. FBS-R-6,3x35 FBS-R-6,3x60 FBS-R-6,3x80 FBS-R-6,3x100 FBS-R-6,3x120 FBS-R-6,3x140 FBS-R-6,3x180 FBS-R-6,3x220
Part number 5763035512 5763060512 5763080512 5763100512 5763120512 5763140512 5763180512 5763220512
EJOT stress plate EcoTek 50 x L Insulation thickness 60 EJOT concrete screw FBS-R-6,3 x L 80 100 120 140 180 220 35 50 70 90 110 130 170 210 65 80 100 120 140 160 200 240 105 120 140 160 180 200 240 280 165 180 200 220 240 260 300 340 225 240 260 280 300 320 360 400
Description Drill bit extension 500mm SDS Blade retainer for EcoTek (drill bit extension) Hammer drill bit A cone 5,0 x 35/102 Hammer drill bit A cone 5,0 x 45/112 Hammer drill bit A cone 5,0 x 52/119 Hammer drill bit A cone 5,0 x 160 Hammer drill bit A cone 5,5 x 160 Hammer drill bit SDS-plus 5,0 x 250/310 Hammer drill bit SDS-plus 5,5 x 200/260 Hammer drill bit SDS-plus 5,5 x 250/310 Bit TORX T30-M6x33
Price / pcs.
Order description 9151950000 9151510071 9200050035 9200050045 9200005052 9200050160 9200055160 9200000028 9200000021 9200000042 9250251430
139
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
APPLICATION RANGE To secure roong membrane to gas concrete substructures2) In combination with EJOT stress plate EcoTek 50 In combination with EJOT stress plate HTV 82/40 F In combination with EJOT stress plate HTV 40 RU FEATURES A4 stainless steel Approved for gas concrete P3.3 onwards No pre-drilling APPROVAL ETA-07/0013 TECHNICAL DATA Drive .............................................hexalobular / TORX T30 Embedment depth ................................................60 mm NOTE 2) As a rule, pull-out tests have to be arranged with our service team for all renovation cases. CROSS REFERENCE Stress plate EcoTek 50 ............................. page 136 Stress plate HTV 82/40 F.......................... page 135 Stress plate HTV 40 RU ............................ page 135
R i vets
S peci a l screw s
S torm w a shers
Price / Order description 100 pcs. FPS-E-8,0x80 FPS-E-8,0x100 FPS-E-8,0x120 FPS-E-8,0x160 FPS-E-8,0x200 FPS-E-8,0x240
P ipe f lashings
EJOT stress plate EcoTek 50 x L Insulation thickness EJOT aerated concrete screw FPS-E-8,0 x L 100 120 160 200 240 35 60 80 120 160 200 65 90 110 150 190 230 105 130 150 190 230 270 165 190 210 250 290 330 225 250 270 310 350 390
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Description Drill bit extension 500mm SDS Blade retainer for EcoTek (drill bit extension) Hammer drill bit A cone 5,0 x 35/102 Hammer drill bit A cone 5,0 x 45/112 Hammer drill bit A cone 5,0 x 52/119 Hammer drill bit A cone 5,0 x 160 Hammer drill bit A cone 5,5 x 160 Hammer drill bit SDS-plus 5,0 x 250/310 Hammer drill bit SDS-plus 5,5 x 200/260 Hammer drill bit SDS-plus 5,5 x 250/310 Bit TORX T30-M6x33
140
Acces sor ie s
Price / Order description pcs. 9151950000 9151510071 9200050035 9200050045 9200005052 9200050160 9200055160 9200000028 9200000021 9200000042 9250251430
Inst al l at i on to ol s
TURNING TORSO, MALM, SWEDEN Supplied by EJOT: EJOT SUPER-SAPHIR self-drilling screw JT3
iStockphoto
R i vets
141
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
R i vets
S peci a l screw s
S torm w a shers
Length range of anchors with zinc-plated steel screws Cr(VI)-free coating Length [mm] 50 60 70 80 100 120 140 160 180 200 220 250 260 275 300 360 1) Delivery time upon request SDF-S10V SDF-KB10V 1) 1) 1) 1) SDF-S10H SDF-KB10H SDF-S -8 SDF-KB -8 SDF-S10U SDF-KB10L SDF-S14U SDF-KB14U SDP-S10S SDP-KB10S SDP-S14 SDP-KB14
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Length range of anchors with A4 stainless steel screws Length [mm] 50 60 70 80 100 120 140 160 180 200 220 1) Delivery time upon request Screw head style and type of drive Design Countersunk Head Hexagon Head T30 T40 A/F 10 A/F 13 A/F 17 SDF-S10V SDF-KB10V SDF-S10H SDF-KB10H SDF-S -8 SDF-KB -8 SDF-S10U SDF-KB10L SDF-S14U SDF-KB14U SDP-S10S SDP-KB10S SDP-S14 SDP-KB14 SDF-S10V SDF-KB10V 1) 1) 1) 1) 1) 1) 1) 1) 1) SDF-S10H SDF-KB10H SDF-S -8 SDF-KB -8 SDF-S10U SDF-KB10L SDF-S14U SDF-KB14U SDP-S10S SDP-KB10S SDP-S14 SDP-KB14
142
Acces sor ie s
Inst al l at i on to ol s
Approval Type of Anchor Nominal drill diameter Drill cut diameter Drill hole depth Embedment depth (concrete + masonry) Embedment depth (concrete) Embedment depth (masonry) Hole diameter of component to be installed Building materials Standard concrete Solid brick Mz 12 Vertically perforated bricks Hlz 12 Vertically perforated brick LHlz1) Solid lime sand brick KS 12 Perforated lime sand brick KSL 6 Slag brick 1) Lightweight concrete cavity block HBL 2 Solid lightweight concrete bricks Solid concrete brick1) Concrete cavity block1) Porous lightweight concrete Porous concrete Porous concrete Lauig/Parchim
1)
ETA-10/0305 SDF-10V dnom / dD [mm] dcut [mm] h1 / t [mm] hnom / hv [mm] hnom,1 / hv [mm] hnom,2 / hv [mm] df [mm] Standard DIN 1045 DIN 105 DIN 105-1 DIN 105-2 DIN 106 DIN 106 DIN 398 DIN 18151 DIN 18152 DIN 18153 DIN 18153 TGL DIN 1053 / 4165 TGL 10 10.45 50 / 60 40 50 10.5 SDF-10V SDF-10H 10 10.45 80 70 70 70 10.5 SDF-10H SDF-8 8 8.45 60 50 50 50 8.5 SDF-8 10
Z-21.2-589 SDF-10U 10.45 80 70 70 70 10.5 SDF-10U SDF-10L 10 10.45 100 90 10.5 SDF-10L SDF-14U 14 14.5 80 70 70 70 14.5 SDF-14U 10
SDP-14
70
Example 1:
Example 2:
SDF-S-10Vx80-V
SDF -S -10 V x80 -V = = = = = = facade screw anchor countersunk head anchor with countersunk head screw anchor diameter in mm solid brick anchor length in mm steel screw with Cr(VI)-free surface
SDF-KB-10Hx120-E
SDF -KB -10 H x120 -E = = = = = = facade screw anchor collar ange anchor with hexagon screw anchor diameter in mm hollow brick anchor length in mm A4 stainless steel screw
143
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
S peci a l screw s
CHARACTERISTIC VALUES Hole depth in concrete h1,1 .................................... 50 mm Effective embedment depth in concrete hnom,1 ......... 40 mm Hole depth in masonry h1,2 .................................... 60 mm Effective embedment depth in masonry hnom,2.......... 50 mm Drill-hole diameter d0 .............................................. 10 mm Hole diameter of construction part to be installed Antrieb .................................. Innensechsrund / TORX T40 CHARACTERISTIC VALUES Tensile load NRk,p in concrete C12/15 Temperature range 30 C / 50 C ...................... 4,50 kN Temperature range 50 C / 80 C ...................... 4,00 kN FRk brick Mz 20-1,8, NF ......................................... 2,50 kN FRk solid lime sand brick KS 36, NF........................... 4,00 kN FRk solid lime sand brick KS 20, 8 DF ........................ 4,50 kN Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw .................................... 7,93 kN Anchor with stainless steel screw A4 .................. 9,12 kN Transverse load VRk,s at hnom,2 = 50 mm Anchor with steel screw .................................. 11,09 kN Anchor with stainless steel screw A4 ................ 12,94 kN Side load MRk,s at hnom,1 =40 mm Anchor with steel screw ................................. 13,80 Nm Anchor with stainless steel screw A4 ............... 16,09 Nm Side load MRk,s at hnom,2 = 50 mm Anchor with steel screw ................................. 23,01 Nm Anchor with stainless steel screw A4 ............... 26,62 Nm PERMITTED LOAD* Tensile load Nper in concrete C12/15 Temperature range 30 C / 50 C ...................... 1,79 kN Temperature range 50 C / 80 C ...................... 1,59 kN Brick Mz 20-1,8, NF .............................................. 0,71 kN Solid lime sand brick KS 36, NF ............................... 1,14 kN Solid lime sand brick KS 20, 8 DF ............................ 1,29 kN Transverse load Vper in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw .................................... 4,53 kN Anchor with stainless steel screw A4 .................. 4,18 kN Transverse load Vper at hnom,2 = 50 mm Anchor with steel screw .................................... 6,34 kN Anchor with stainless steel screw A4 .................. 5,92 kN Max. permitted side load hnom,1 =40 mm Anchor with steel screw ....................................7,89 Nm Anchor with stainless steel screw A4 ..................7,37 Nm Max. permitted side load at hnom,2 = 50 mm Anchor with steel screw ................................. 13,15 Nm Anchor with stainless steel screw A4 ............... 12,19 Nm NOTES Please note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval. *For calculation of the acceptable loading the material safety value JM and the factoral load JF = 1,4 were included.
R i vets
S torm w a shers
APPLICATION RANGE Installation of wood or metal components For all non-load carrying redundant systems according to ETAG 020 Suitable for the structural fastening of gates, doors, windows, square timber
Concrete
Masonry
in mm
Anchor length L mm
PU
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 50 10 100 10 60 20 10 100 10 70 30 20 100 10 80 40 30 100 10 100 60 50 100 10 120 80 70 100 10 140 100 90 100 10 160 120 110 100 10 180 140 130 100 10 200 160 150 100 10 220 180 170 100
SDF-S-10Vx50-V SDF-S-10Vx60-V SDF-S-10Vx70-V SDF-S-10Vx80-V SDF-S-10Vx100-V SDF-S-10Vx120-V SDF-S-10Vx140-V SDF-S-10Vx160-V SDF-S-10Vx180-V SDF-S-10Vx200-V SDF-S-10Vx220-V
8580050450 8580060450 8580070450 8580080450 8580100450 8580120450 8580140450 8580160450 8580180450 8580200450 8580220450
P ipe f lashings
144
Acces sor ie s
Inst al l at i on to ol s
FEATURES Anchor with an embedment depth of 40 mm in concrete Two installation depths (embedment in masonry 50 mm) Very short expansion part, for short installation times Optimal expanding part due to radial expansion Very high bending moment Cr VI-free coating of the screw Product identification through different sleeve colours Double safety lock against torsion for secure installation
APPROVAL ETA-10/0305 INSTALLATION SUBSTRATE Approved for: Concrete Solid brick Solid lime sand brick Solid lightweight concrete brick Suitable for: Natural stone with compact structure Plaster board
h h1,1 hnom,1
Concrete
Masonry
in mm
Anchor length L mm
PU
Part number
*For calculation of the acceptable loading the material safety value JM and the factoral load JF = 1,4 were included.
145
Acces sor ie s
FEATURES Anchor with an embedment depth of 40 mm in concrete Two installation depths (embedment in masonry 50 mm) Very short expansion part, for short installation times Optimal expanding part due to radial expansion Very high bending moment Cr VI-free coating of the screw Product identification through different sleeve colours Double safety lock against torsion for secure installation
APPROVAL ETA-10/0305 INSTALLATION SUBSTRATE Approved for: Concrete Solid brick Solid lime sand brick Solid lightweight concrete brick Suitable for: Natural stone with compact structure Plaster board
NOTES Please note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval.
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 50 10 100 10 60 20 10 100 10 70 30 20 100 10 80 40 30 100 10 100 60 50 100 10 120 80 70 100 10 140 100 90 100 10 160 120 110 100 10 180 140 130 100 10 200 160 150 100 10 220 180 170 100 Anchor with A4 stainless steel screws (-E) 10 50 10 100 10 60 20 10 100 10 70 30 20 100
SDF-KB-10Vx50-V SDF-KB-10Vx60-V SDF-KB-10Vx70-V SDF-KB-10Vx80-V SDF-KB-10Vx100-V SDF-KB-10Vx120-V SDF-KB-10Vx140-V SDF-KB-10Vx160-V SDF-KB-10Vx180-V SDF-KB-10Vx200-V SDF-KB-10Vx220-V
8581050450 8581060450 8581070450 8581080450 8581100450 8581120450 8581140450 8581160450 8581180450 8581200450 8581220450
PERMITTED LOAD* Tensile load Nper in concrete C12/15 Temperature range 30 C / 50 C ...................... 1,79 kN Temperature range 50 C / 80 C ...................... 1,59 kN Brick Mz 20-1,8, NF .............................................. 0,71 kN Solid lime sand brick KS 36, NF ............................... 1,14 kN Solid lime sand brick KS 20, 8 DF ............................ 1,29 kN Transverse load Vper in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw .................................... 4,53 kN Anchor with stainless steel screw A4 .................. 4,18 kN Transverse load Vper at hnom,2 = 50 mm Anchor with steel screw .................................... 6,34 kN Anchor with stainless steel screw A4 .................. 5,92 kN Max. permitted side load hnom,1 =40 mm Anchor with steel screw ....................................7,89 Nm Anchor with stainless steel screw A4 ..................7,37 Nm Max. permitted side load at hnom,2 = 50 mm Anchor with steel screw ................................. 13,15 Nm Anchor with stainless steel screw A4 ............... 12,19 Nm
P ipe f lashings
CHARACTERISTIC VALUES Tensile load NRk,p in concrete C12/15 Temperature range 30 C / 50 C ...................... 4,50 kN Temperature range 50 C / 80 C ...................... 4,00 kN FRk brick Mz 20-1,8, NF ......................................... 2,50 kN FRk solid lime sand brick KS 36, NF........................... 4,00 kN FRk solid lime sand brick KS 20, 8 DF ........................ 4,50 kN Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw .................................... 7,93 kN Anchor with stainless steel screw A4 .................. 9,12 kN Transverse load VRk,s at hnom,2 = 50 mm Anchor with steel screw .................................. 11,09 kN Anchor with stainless steel screw A4 ................ 12,94 kN Bending moment MRk,s at hnom,1 =40 mm Anchor with steel screw ................................. 13,80 Nm Anchor with stainless steel screw A4 ............... 16,09 Nm Side load MRk,s at hnom,2 = 50 mm Anchor with steel screw ................................. 23,01 Nm Anchor with stainless steel screw A4 ............... 26,62 Nm
R i vets
S peci a l screw s
t fix t tol
h h1,2 hnom,2
t fix t tol
S torm w a shers
APPLICATION RANGE Installation of metal components For all non-load carrying redundant systems according to ETAG 020 Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces
CHARACTERISTIC VALUES Hole depth in concrete h1,1 .................................... 50 mm Effective embedment depth in concrete hnom,1 ......... 40 mm Hole depth in masonry h1,2 .................................... 60 mm Effective embedment depth in masonry hnom,2.......... 50 mm Drill-hole diameter d0 .............................................. 10 mm Hole diameter of construction part to be installed Drive .................. hexagon A/F13 + hexalobular / TORX T40
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
CHARACTERISTIC VALUES Hole depth h1 ...................................................... 80 mm Effective embedment depth hnom ........................... 70 mm Drill-hole diameter d0 ........................................... = 10 mm Hole diameter of construction part to be installed Drive ............................................ hexalobular / TORX T40 CHARACTERISTIC VALUES Tensile load NRk,p in concrete C12/15 Temperature range 30 C / 50 C ............................ 4,50 kN Temperature range 50 C / 80 C ............................ 4,00 kN Brick Mz 20-1,8, NF .............................................. 4,00 kN Solid lime sand brick KS 36, NF ............................... 4,50 kN Solid lime sand brick KS 20, 8 DF ............................ 4,50 kN Solid lightweight concrete brick V6, 2 DF .................. 2,00 kN Porous lightweight concrete.................................... 2,00 kN Vertically perforated brick HLz 12-0,9, NF ................ 2,00 kN Perforated lime sand brick KSL 12, 4 DF .................. 2,50 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF .. 1,20 kN Transverse load VRk,s Anchor with steel screw ......................................... 9,35 kN Anchor with stainless steel screw A4 ..................... 10,91 kN Side load MRk,s Anchor with steel screw ...................................... 17,67 Nm Anchor with stainless steel screw A4 .................... 20,62 Nm PERMITTED LOAD* Tensile load Nper in concrete C12/15 Temperature range 30 C / 50 C ............................ 1,79 kN Temperature range 50 C / 80 C ............................ 1,59 kN Brick Mz 20-1,8, NF .............................................. 1,14 kN Solid lime sand brick KS 36, NF ............................... 1,29 kN Solid lime sand brick KS 20, 8 DF ............................ 1,29 kN Solid lightweight concrete brick V6, 2 DF .................. 0,57 kN Porous lightweight concrete.................................... 0,57 kN Vertically perforated brick HLz 12-0,9, NF ................ 0,57 kN Perforated lime sand brick KSL 12, 4 DF .................. 0,71 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF .. 0,34 kN Transverse load Vzul Anchor with steel screw ......................................... 5,34 kN Anchor with stainless steel screw A4 ....................... 5,00 kN Max. permitted side load Anchor with steel screw ...................................... 10,10 Nm Anchor with stainless steel screw A4 ...................... 9,44 Nm NOTES For planning and processing of the product please note the European Technical Approval ETA-10/0305. Further information about parameters and loads can be found in the approval. *For the calculation of the acceptable loading the material safety value JM and the factoral load JF = 1,4 were included.
APPLICATION RANGE Installation of wood or metal components For all non-load carrying redundant systems according to ETAG 020 Suitable for the structural fastening of gates, doors, windows, square timber For installation in external wall panels made of concrete
h h1 hnom t fix t tol
R i vets
S peci a l screw s
S torm w a shers
Installation substrate
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Anchor Fixing Price length L thickness tx PU / 100 Order description mm mm pcs. Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 80 10 100 SDF-S-10Hx80-V 10 100 30 100 SDF-S-10Hx100-V 10 120 50 100 SDF-S-10Hx120-V 10 140 70 100 SDF-S-10Hx140-V 10 160 90 100 SDF-S-10Hx160-V 10 180 110 100 SDF-S-10Hx180-V 10 200 130 100 SDF-S-10Hx200-V 10 220 150 100 SDF-S-10Hx220-V Anchor with A4 stainless steel screws (-E) 10 80 10 100 SDF-S-10Hx80-E 10 100 30 100 SDF-S-10Hx100-E 10 120 50 100 SDF-S-10Hx120-E 10 140 70 100 SDF-S-10Hx140-E 10 160 90 100 SDF-S-10Hx160-E 10 180 110 100 SDF-S-10Hx180-E 10 200 130 100 SDF-S-10Hx200-E 10 220 150 100 SDF-S-10Hx220-E mm
Part number
P ipe f lashings
8510080420 8510100420 8510120420 8510140420 8510160420 8510180420 8510200420 8510220420 8510080620 8510100620 8510120620 8510140620 8510160620 8510180620 8510200620 8510220620
Acces sor ie s
Inst al l at i on to ol s
FEATURES Approved for all common building materials Reliable installation in problematic building material due to optimised expansion part Secure hold due to radial expansion Cr VI-free coating of the screw Product identification through different sleeve colours Double safety lock against torsion for secure installation APPROVAL ETA-10/0305
INSTALLATION SUBSTRATE Approved for: Concrete Solid brick Solid lime sand brick Solid lightweight concrete brick Vertically perforated brick Lightweight vertically perforated brick Perforated lime sand brick Lightweight concrete cavity block Porous lightweight concrete Suitable for: Natural stone Plaster board Non-classied cavity and perforated brick
146
APPLICATION RANGE Installation of metal components For all non-load carrying redundant systems according to ETAG 020 Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces For installation in external wall panels made of concrete
CHARACTERISTIC VALUES Hole depth h1 ...................................................... 80 mm Effective embedment depth hnom ........................... 70 mm Drill-hole diameter d0 ........................................... = 10 mm Hole diameter of construction part to be installed Drive .................... hexagon A/F13 + hexalobular TORX T40 CHARACTERISTIC VALUES Tensile load NRk,p in concrete C12/15 Temperature range 30 C / 50 C ............................ 4,50 kN Temperature range 50 C / 80 C ............................ 4,00 kN Brick Mz 20-1,8, NF .............................................. 4,00 kN Solid lime sand brick KS 36, NF ............................... 4,50 kN Solid lime sand brick KS 20, 8 DF ............................ 4,50 kN Solid lightweight concrete brick V6, 2 DF .................. 2,00 kN Porous lightweight concrete.................................... 2,00 kN Vertically perforated brick HLz 12-0,9, NF ................ 2,00 kN Perforated lime sand brick KSL 12, 4 DF .................. 2,50 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF .. 1,20 kN Transverse load VRk,s Anchor with steel screw ......................................... 9,35 kN Anchor with stainless steel screw A4 ..................... 10,91 kN Side load MRk,s Anchor with steel screw ...................................... 17,67 Nm Anchor with stainless steel screw A4 .................... 20,62 Nm PERMITTED LOAD* Tensile load Nper in concrete C12/15 Temperature range 30 C / 50 C ............................ 1,79 kN Temperature range 50 C / 80 C ............................ 1,59 kN Brick Mz 20-1,8, NF .............................................. 1,14 kN Solid lime sand brick KS 36, NF ............................... 1,29 kN Solid lime sand brick KS 20, 8 DF ............................ 1,29 kN Solid lightweight concrete brick V6, 2 DF .................. 0,57 kN Porous lightweight concrete.................................... 0,57 kN Vertically perforated brick HLz 12-0,9, NF ................ 0,57 kN Perforated lime sand brick KSL 12, 4 DF .................. 0,71 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF .. 0,34 kN Transverse load Vzul Anchor with steel screw ......................................... 5,34 kN Anchor with stainless steel screw A4 ....................... 5,00 kN Max. permitted side load Anchor with steel screw ...................................... 10,10 Nm Anchor with stainless steel screw A4 ...................... 9,44 Nm NOTES For planning and processing of the product please note the European Technical Approval ETA-10/0305. Further information about parameters and loads can be found in the approval. *For the calculation of the acceptable loading the material safety value JM and the factoral load JF = 1,4 were included.
Installation substrate
APPROVAL ETA-10/0305
147
Acces sor ie s
Inst al l at i on to ol s
FEATURES Approved for all common building materials Reliable installation in problematic building material due to optimised expansion part Secure hold due to radial expansion Cr VI-free coating of the screw Product identification through different sleeve colours Double safety lock against torsion for secure installation
INSTALLATION SUBSTRATE Approved for: Concrete Solid brick Solid lime sand brick Solid lightweight concrete brick Vertically perforated brick Lightweight vertically perforated brick Perforated lime sand brick Lightweight concrete cavity block Porous lightweight concrete Suitable for: Natural stone Plaster board Non-classied cavity and perforated brick
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Fixing Price Anchor thickness tx length L PU / 100 Order description mm pcs. mm Anchor with steel screw with zinc-plated Cr(VI)-free coating (-V) 10 80 10 100 SDF-KB-10Hx80-V 10 100 30 100 SDF-KB-10Hx100-V 10 120 50 100 SDF-KB-10Hx120-V 10 140 70 100 SDF-KB-10Hx140-V 10 160 90 100 SDF-KB-10Hx160-V 10 180 110 100 SDF-KB-10Hx180-V 10 200 130 100 SDF-KB-10Hx200-V 10 220 150 100 SDF-KB-10Hx220-V Anchor with A4 stainless steel screws (-E) 10 80 10 100 SDF-KB-10Hx80-E 10 100 30 100 SDF-KB-10Hx100-E 10 120 50 100 SDF-KB-10Hx120-E 10 140 70 100 SDF-KB-10Hx140-E 10 160 90 100 SDF-KB-10Hx160-E 10 180 110 100 SDF-KB-10Hx180-E 10 200 130 100 SDF-KB-10Hx200-E 10 220 150 100 SDF-KB-10Hx220-E in mm
Part number
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For xing timber substructures to solid brick masonry and concrete For installation in external wall panels made of concrete FEATURES Small drill-hole diameter Cr(VI)-free coating Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive .............................................hexalobular / TORX T30 Hole depth t ....................................................... 60 mm Embedment depth hv .......................................... 50 mm PERMITTED LOADS Concrete C12/15 ................................................. 0.5 kN Solid brick Mz 12.................................................. 0.4 kN Unperforated solid brick Mz 12 .............................. 0.5 kN Sand-lime solid brick KS 12 ................................... 0.4 kN Unperforated sand-lime solid brick KS 12 ............... 0.5 kN Light-weight solid brick V 2.................................. 0.15 kN External wall panels made of concrete C12/15 ...... 0.25 kN Maximum allowable bending moment steel ............... 4,7 Nm Maximum allowable bending moment stainless steel .. 5,3 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
R i vets
S peci a l screw s
S torm w a shers
148
Acces sor ie s
Inst al l at i on to ol s
Anchor Fixing Price length L thickness B PU / 100 Order description mm mm pcs. Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 8 80 30 100 SDF-S-8x80-V 8 100 50 100 SDF-S-8x100-V 8 120 70 100 SDF-S-8x120-V 8 140 90 100 SDF-S-8x140-V 8 160 110 100 SDF-S-8x160-V 8 180 130 100 SDF-S-8x180-V 8 200 150 100 SDF-S-8x200-V* 8 220 170 100 SDF-S-8x220-V* Anchor with A4 stainless steel screws (-E) 8 80 30 100 SDF-S-8x80-E* 8 100 50 100 SDF-S-8x100-E 8 120 70 100 SDF-S-8x120-E 8 140 90 100 SDF-S-8x140-E 8 160 110 100 SDF-S-8x160-E 8 180 130 100 SDF-S-8x180-E 8 200 150 100 SDF-S-8x200-E* 8 220 170 100 SDF-S-8x220-E* * Delivery time upon request mm
Part number
8566880403 8566810403 8566812403 8566814403 8566816403 8566818403 8566820403 8566822403 8566880606 8566810606 8566812606 8566814606 8566816606 8566818606 8566820606 8566822606
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE For xing metal substructures to solid brick masonry and concrete For installation in external wall panels made of concrete FEATURES Hexagon head with flange Small drill-hole diameter Cr(VI)-free coating Thermal and galvanic separation Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive .......................................................... hexagon A/F10 Hole depth t ....................................................... 60 mm Embedment depth hv .......................................... 50 mm Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 8 60 10 100 SDF-KB-8x60-V 8 80 30 100 SDF-KB-8x80-V 8 100 50 100 SDF-KB-8x100-V 8 120 70 100 SDF-KB-8x120-V 8 140 90 100 SDF-KB-8x140-V 8 160 110 100 SDF-KB-8x160-V 8 180 130 100 SDF-KB-8x180-V 8 200 150 100 SDF-KB-8x200-V* 8 220 170 100 SDF-KB-8x220-V* Anchor with A4 stainless steel screws (-E) 8 60 10 100 SDF-KB-8x60-E 8 80 30 100 SDF-KB-8x80-E 8 100 50 100 SDF-KB-8x100-E 8 120 70 100 SDF-KB-8x120-E 8 140 90 100 SDF-KB-8x140-E 8 160 110 100 SDF-KB-8x160-E 8 180 130 100 SDF-KB-8x180-E 8 200 150 100 SDF-KB-8x200-E* 8 220 170 100 SDF-KB-8x220-E* * Delivery time upon request mm Part number PERMITTED LOADS Concrete C12/15 ................................................. 0.5 kN Solid brick Mz 12.................................................. 0.4 kN Unperforated solid brick Mz 12 .............................. 0.5 kN Sand-lime solid brick KS 12 ................................... 0.4 kN Unperforated sand-lime solid brick KS 12 ............... 0.5 kN Light-weight solid brick V 2.................................. 0.15 kN External wall panels made of concrete C12/15 ...... 0.25 kN Maximum allowable bending moment steel ............... 4,7 Nm Maximum allowable bending moment stainless steel .. 5,3 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
149
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For xing timber substructures to perforated brick, solid brick masonry and concrete For xing in external wall panels made of concrete and porous lightweight concrete FEATURES High bending moment High loads Cr(VI)-free coating Embedment in all standard building materials Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive ............................................ hexalobular / TORX T40 Hole depth t ........................................................ 80 mm Embedment depth hv ........................................... 70 mm PERMITTED LOADS Concrete C12/15 ................................................. 1.6 kN Solid brick Mz 12.................................................. 0.6 kN Unperforated solid brick Mz 12 .............................. 0.8 kN Sand-lime solid brick KS 12 ................................... 0.6 kN Unperforated sand-lime solid brick KS 12 ............... 0.8 kN Vertically perforated brick Hlz 12 ............................ 0.5 kN Sand-lime perforated brick KSL 6 ........................... 0.4 kN Light-weight cavity block Hbl 2 ............................ 0.25 kN Light-weight solid brick V 2.................................. 0.25 kN External wall panels made of concrete C12/15 ........ 0.6 kN Porous lightweight concrete (hv 90 mm) .................. 0.3 kN Maximum allowable bending moment steel ..............11,5 Nm Maximum allowable bending moment stainless steel .13,0 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169 NOTE An additional large diameter washer acc. to DIN 9021 must be used for fastening metal parts.
R i vets
S peci a l screw s
S torm w a shers
Anchor Fixing Price length L thickness B PU / 100 Order description mm mm pcs. Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 250 180 100 SDF-S-10Ux250-V 10 275 205 100 SDF-S-10Ux275-V 10 300 230 100 SDF-S-10Ux300-V mm
Part number
150
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE For fixing metal substructure to perforated brick For fixing in external wall panels made of concrete and porous lightweight concrete FEATURES Hexagon head with flange Large percentage contact area in vertically perforated brick High bending moment Cr VI-free surface Thermal and galvanic separation Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive .......................................................... hexagon A/F13 Hole depth t ...................................................... 100 mm Embedment depth hv ........................................... 90 mm PERMITTED LOADS Vertically perforated brick Hlz 12 ............................ 0.3 kN Sand-lime perforated brick KSL 6 ........................... 0.4 kN Light-weight cavity block Hbl 2 ............................ 0.25 kN Light-weight solid brick V 2.................................. 0.25 kN External wall panels made of concrete C12/15 .........0.4 kN Porous lightweight concrete (hv 90 mm) ................. 0.5 kN Maximum allowable bending moment steel ..............11,5 Nm Maximum allowable bending moment stainless steel .13,0 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
8755120602
151
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Anchor Fixing Price length L thickness B PU / 100 Order description mm mm pcs. Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 120 30 100 SDF-KB-10Lx120-V mm
Part number
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For fixing timber substructure to perforated brick, solid brick masonry and concrete For embedment in porous lightweight concrete FEATURES Optimum security against torsion Cr(VI)-free coating High load-carrying capacity Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive ............................................ hexalobular / TORX T40 Hole depth t ........................................................ 80 mm Embedment depth hv ........................................... 70 mm PERMITTED LOADS Concrete C12/15 ................................................. 1.8 kN Solid brick Mz 12.................................................. 0.6 kN Unperforated solid brick Mz 12 .............................. 0.8 kN Sand-lime solid brick KS 12 ................................... 0.6 kN Unperforated sand-lime solid brick KS 12 ............... 0.8 kN Vertically perforated brick Hlz 12 ............................ 0.5 kN Sand-lime perforated brick KSL 6 ........................... 0.6 kN Light-weight cavity block Hbl 2 .............................. 0.3 kN Light-weight solid brick V 2.................................... 0.5 kN Porous lightweight concrete (hv 90 mm) .................. 0.7 kN Maximum allowable bending moment steel ............. 26,3 Nm Maximum allowable bending moment stainless steel 24,7 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169 NOTE An additional large diameter washer acc. to DIN 9021 must be used for fastening metal parts.
R i vets
S peci a l screw s
S torm w a shers
152
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 14 120 50 50 SDF-S-14Ux120-V 14 140 70 50 SDF-S-14Ux140-V 14 180 110 50 SDF-S-14Ux180-V 14 220 150 50 SDF-S-14Ux220-V 14 260 190 50 SDF-S-14Ux260-V 14 300 230 50 SDF-S-14Ux300-V 14 360 290 50 SDF-S-14Ux360-V mm
Part number
P ipe f lashings
APPLICATION RANGE For fixing metal substructures in perforated brick, solid brick masonry and concrete For embedment in porous lightweight concrete FEATURES Hexagon head with flange Optimum security against torsion Cr(VI)-free coating High load-carrying capacity Product identification through different sleeve colours APPROVAL Z-21.2-589 CHARACTERISTIC VALUES Drive .......................................................... hexagon A/F17 Hole depth t ........................................................ 80 mm Embedment depth hv ........................................... 70 mm PERMITTED LOADS Concrete C12/15 ................................................. 1.8 kN Solid brick Mz 12.................................................. 0.6 kN Unperforated solid brick Mz 12 .............................. 0.8 kN Sand-lime solid brick KS 12 ................................... 0.6 kN Unperforated sand-lime solid brick KS 12 ............... 0.8 kN Vertically perforated brick Hlz 12 ............................ 0.5 kN Sand-lime perforated brick KSL 6 ........................... 0.6 kN Light-weight cavity block Hbl 2 .............................. 0.3 kN Light-weight solid brick V 2.................................... 0.5 kN Porous lightweight concrete (hv 90 mm) .................. 0.7 kN Maximum allowable bending moment steel ............. 26,3 Nm Maximum allowable bending moment stainless steel 24,7 Nm NOTE For planning and processing please note approval Z-21-2-589 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
mm
153
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 14 80 10 50 SDF-KB-14Ux80-V 14 100 30 50 SDF-KB-14Ux100-V
Part number
8740080602 8740100602
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For xing timber substructure to aerated concrete For xing timber substructure to aerated concrete from Lauig and Parchim FEATURES Reliable form-fit due to combined expansion zones Cr(VI)-free coating Fast rotary hole drilling Product identification through different sleeve colours High anchoring stability even into soft aerated concrete APPROVAL Z-21.2-967 CHARACTERISTIC VALUES Drive .............................................hexalobular / TORX T40 Hole depth t ....................................................... 80 mm Embedment depth hv .......................................... 70 mm PERMITTED LOADS Aerated concrete PP2 / P3,3 acc. to DIN .................... 0.3 kN Aerated concrete PP4 / P4,4 acc. to DIN ................. 0.6 kN Aerated concrete in accordance with TGL Werk Lauig 0.4 kN Aerated concrete in accordance with TGL Werk Parchim; 0.2 kN Maximum allowable bending moment steel ..............11,5 Nm Maximum allowable bending moment stainless steel .13,0 Nm NOTE For planning and processing please note approval Z-21-2-967 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
R i vets
S peci a l screw s
S torm w a shers
Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 80 10 100 SDP-S-10Sx80-V 10 100 30 100 SDP-S-10Sx100-V 10 120 50 100 SDP-S-10Sx120-V 10 140 70 100 SDP-S-10Sx140-V 10 160 90 100 SDP-S-10Sx160-V 10 180 110 100 SDP-S-10Sx180-V 10 200 130 100 SDP-S-10Sx200-V* 10 220 150 100 SDP-S-10Sx220-V* Anchor with A4 stainless steel screws (-E) 10 80 10 100 SDP-S-10Sx80-E 10 100 30 100 SDP-S-10Sx100-E 10 120 50 100 SDP-S-10Sx120-E 10 140 70 100 SDP-S-10Sx140-E 10 160 90 100 SDP-S-10Sx160-E 10 180 110 100 SDP-S-10Sx180-E 10 200 130 100 SDP-S-10Sx200-E* 10 220 150 100 SDP-S-10Sx220-E* * Delivery time upon request mm
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
8774080423 8774100423 8774120423 8774140423 8774160423 8774180423 8774200423 8774220423 8774080623 8774100623 8774120623 8774140623 8774160623 8774180623 8774200623 8774220623
154
Acces sor ie s
Inst al l at i on to ol s
P ipe f lashings
APPLICATION RANGE For xing metal substructures to aerated concrete For xing metal substructures to aerated concrete from Lauig and Parchim FEATURES Hexagon head with flange Reliable form-fit due to combined expansion zones high anchoring stability even into soft gas concrete Cr(VI)-free coating Thermal and galvanic separation Product identification through different sleeve colours Fast rotary hole drilling APPROVAL Z-21.2-967 CHARACTERISTIC VALUES Drive .......................................................... hexagon A/F13 Hole depth t ........................................................ 80 mm Embedment depth hv ........................................... 70 mm Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 10 80 10 100 SDP-KB-10Sx80-V 10 100 30 100 SDP-KB-10Sx100-V 10 120 50 100 SDP-KB-10Sx120-V 10 140 70 100 SDP-KB-10Sx140-V 10 160 90 100 SDP-KB-10Sx160-V 10 180 110 100 SDP-KB-10Sx180-V 10 200 130 100 SDP-KB-10Sx200-V* 10 220 150 100 SDP-KB-10Sx220-V* Anchor with A4 stainless steel screws (-E) 10 80 10 100 SDP-KB-10Sx80-E 10 100 30 100 SDP-KB-10Sx100-E 10 120 50 100 SDP-KB-10Sx120-E 10 140 70 100 SDP-KB-10Sx140-E 10 160 90 100 SDP-KB-10Sx160-E 10 180 110 100 SDP-KB-10Sx180-E 10 200 130 100 SDP-KB-10Sx200-E* 10 220 150 100 SDP-KB-10Sx220-E* * Delivery time upon request mm Part number PERMITTED LOADS Aerated concrete PP2 / P3,3 acc. to DIN .................... 0.3 kN Aerated concrete PP4 / P4,4 acc. to DIN ................. 0.6 kN Aerated concrete in accordance with TGL Werk Lauig 0.4 kN Aerated concrete in accordance with TGL Werk Parchim; 0.2 kN Maximum allowable bending moment steel ..............11,5 Nm Maximum allowable bending moment stainless steel .13,0 Nm NOTE For planning and processing please note approval Z-21-2-967 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
155
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Facade anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For xing timber substructure to aerated concrete For xing timber substructure to aerated concrete from Lauig and Parchim FEATURES Very robust Easy and quick installation Cr(VI)-free coating Thermal and galvanic separation Product identification through different sleeve colours High bending moment Fast rotary hole drilling High embedment stability even in soft gas concrete APPROVAL Z-21.2-967 CHARACTERISTIC VALUES Drive ............................................ hexalobular / TORX T40 Hole depth t ....................................................... 80 mm Embedment depth hv .......................................... 70 mm PERMITTED LOADS Aerated concrete PP2 / P3,3 acc. to DIN .................... 0.4 kN Aerated concrete PP4 / P4,4 acc. to DIN ................. 0.8 kN Aerated concrete in accordance with TGL Werk Lauig 0.5 kN Aerated concrete in accordance with TGL Werk Parchim . 0.3 kN Maximum allowable bending moment steel ............. 26,3 Nm Maximum allowable bending moment stainless steel 24,7 Nm NOTE For planning and processing please note approval Z-21-2-967 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169 Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 14 120 50 50 SDP-S-14x120-V 14 140 70 50 SDP-S-14x140-V 14 180 110 50 SDP-S-14x180-V 14 220 150 50 SDP-S-14x220-V mm Part number
R i vets
S peci a l screw s
S torm w a shers
156
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
APPLICATION RANGE For xing metal substructure to aerated concrete For xing metal substructures to gas concrete from Lauig and Parchim FEATURES Hexagon head with flange Very robust Easy and quick installation Cr(VI)-free coating Thermal and galvanic separation Product identification through different sleeve colours High bending moment Fast rotary hole drilling High embedment stability even in soft gas concrete APPROVAL Z-21.2-967 CHARACTERISTIC VALUES Drive .......................................................... hexagon A/F17 Hole depth t ....................................................... 80 mm Embedment depth hv .......................................... 70 mm Part number PERMITTED LOADS Gas concrete PP2 / P3,3 acc. to DIN .......................... 0.4 kN Gas concrete PP4 / P4,4 acc. to DIN ....................... 0.8 kN Gas concrete in accordance with TGL Werk Lauig ...... 0.5 kN Gas concrete in accordance with TGL Werk Parchim .... 0.3 kN Maximum allowable bending moment steel ............. 26,3 Nm Maximum allowable bending moment stainless steel 24,7 Nm NOTE For planning and processing please note approval Z-21-2-967 CROSS REFERENCE Blow-out pump........................................ page 190 Installation tools ...................................... page 169
157
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Anchor Fixing Price Order description length L thickness B PU / 100 pcs. mm mm Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V) 14 80 10 50 SDP-KB-14x80-V* 14 100 30 50 SDP-KB-14x100-V* Anchor with A4 stainless steel screws (-E) 14 80 10 50 SDP-KB-14x80-E* 14 100 30 50 SDP-KB-14x100-E* * Delivery time upon request mm
8769080310 8769100310
P ipe f lashings
8769080602 8769100602
R i vets
S peci a l screw s
S torm w a shers
158
R i vets
Acces sor ie s
Inst al l at i on to ol s
Ancho rs and Embe dmen t Tec hnol og y P ipe f lashings S caf f olding fast ener s D ir ect Fast ening S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Notes
AVAZ TWIST TOWER, SARAJEVO, BOSNIA AND HERZEGOVINA Supplied by EJOT: EJOT SAPHIR self-drilling screw JT2, EJOT facade anchor
USE OF THE MATERIAL Application range Dry indoor use Wet indoor use Indoor swimming pools Auto tunnels
INSTALLATION INSTRUCTION
159
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Steel anchors
S el f-dri l l i ng screw s
S torm w a shers
APPLICATION RANGE For embedment in cracked and non-cracked concrete C20/25 FEATURES Zinc-plated steel Approval for concrete, option I Fire-resistance classes F30, F60, F90, F120 APPROVAL ETA-08/0173
R i vets
S peci a l screw s
NOTE Characteristic values apply to the compression strength of C20/25 concrete. Design load of an anchor for central tension in cracked concrete. CROSS REFERENCE Blow-out pump........................................ page 190
in mm
Length L mm
Fixing thickness B mm
Hole depth h1 mm
PU
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
72 92 112 147 92 102 112 132 162 103 118 128 163 178 123 138 168 170 220
10 30 50 85 10 20 30 50 80 5 20 30 65 80 5 20 50 20 70
45 45 45 45 60 60 60 60 60 70 70 70 70 70 85 85 85 110 110
50 50 40 40 40 25 25 25 25 20 20 20 20 20 10 10 10 5 5
S-KA 8/10-V S-KA 8/30-V S-KA 8/50-V S-KA 8/85-V S-KA 10/10-V S-KA 10/20-V S-KA 10/30-V S-KA 10/50-V S-KA 10/80-V S-KA 12/5-V S-KA 12/20-V S-KA 12/30-V S-KA 12/65-V S-KA 12/80-V S-KA 16/5-V S-KA 16/20-V S-KA 16/50-V S-KA 20/20-V S-KA 20/70-V
9650001112 9650001114 9650001116 9650001118 9650001132 9650001135 9650001136 9650001137 9650001139 9650001150 9650001152 9650001153 9650001155 9650001157 9650001170 9650001171 9650001173 9650001180 9650001182
P ipe f lashings
Order information: Further lengths upon request. *Not part of the ETA
160
Acces sor ie s
Inst al l at i on to ol s
APPLICATION RANGE For embedment in cracked and non-cracked concrete C20/25 HCR (1.4529) anchor for embedment in chlorinated atmosphere available upon request FEATURES A4 stainless steel Approval for concrete, option I Fire-resistance classes F30, F60, F90, F120 APPROVAL ETA-08/0173 Part number NOTE Characteristic values apply to the compression strength of C20/25 concrete. Design load of an anchor for central tension in cracked concrete. CROSS REFERENCE Blow-out pump........................................ page 190
in mm
Length L mm
168
50
110
85
10
S-KAH 16/50-E
9650005172
161
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Order information: Further lengths upon request. *Not part of the ETA
P ipe f lashings
15 10 50 10 30 50 5 20 30
50 60 60 75 75 75 90 90 90
35 45 45 60 60 60 70 70 70
100 50 40 40 25 25 20 20 20
S-KAH 6/15-E S-KAH 8/10-E S-KAH 8/50-E S-KAH 10/10-E S-KAH 10/30-E S-KAH 10/50-E S-KAH 12/5-E S-KAH 12/20-E S-KAH 12/30-E
Fixing thickness B mm
Hole depth h1 mm
PU
R i vets
S peci a l screw s
S torm w a shers
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Nail anchors
S el f-dri l l i ng screw s
S torm w a shers
APPLICATION RANGE For easy and quick installation For light and constructional fastening FEATURES Zinc-plated steel With pre-assembled special nail For all pressure-resistant building materials Easy to remove RECOMMENDED WORK LOAD Hole depth t ....................................................... 40 mm Embedment depth hv .............................................. 30 mm RECOMMENDED WORK LOAD Concrete................................................................. 0.3 kN Solid brick............................................................. 0.25 kN Perforated brick..................................................... 0.25 kN mm 6 6 6 6 Anchor length L mm 35 45 55 70 Clamping thickness B mm 5 15 25 40 PU 100 100 100 100 Price / Order description 100 pcs. ND-K-6x35 ND-K-6x45 ND-K-6x55 ND-K-6x70 Part number 8561635400 8561645400 8561655400 8561670400
P ipe f lashings
R i vets
S peci a l screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
APPLICATION RANGE For easy and quick installation For light and constructional fastening FEATURES Zinc-plated steel With pre-assembled special nail For all pressure-resistant building materials Easy to remove RECOMMENDED WORK LOAD Hole depth t ....................................................... 55 mm Embedment depth hv .............................................. 45 mm RECOMMENDED WORK LOAD Concrete............................................................... 0.40 kN Solid brick............................................................. 0.30 kN Perforated brick..................................................... 0.30 kN mm 8 8 8 Anchor length L mm 60 75 100 Clamping thickness B mm 15 35 55 PU 50 50 50 Price / Order description 100 pcs. ND-K-8x60 ND-K-8x75 ND-K-8x100 Part number 8561860400 8561875400 8561800400
162
Acces sor ie s
Inst al l at i on to ol s
PU
Part number
163
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
8 8 8 8 8 8 8 8 8 8
350 300 250 250 200 150 150 100 100 100
DH-8x60 DH-8x80 DH-8x100 DH-8x120 DH-8x140 DH-8x160 DH-8x180 DH-8x200 DH-8x220 DH-8x240
8551906009 8551908009 8551910090 8551912009 8551914000 8551916009 8551918009 8551920009 8551922009 8551924009
NOTE The EJOT insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm. The insulation board fastening is carried-out according to DIN 18516-1.
R i vets
mm
Anchor length L mm
mm mm mm mm mm
S peci a l screw s
S torm w a shers
APPLICATION RANGE For fastening hard insulating materials in combination with the EJOT DMT metal insulation stress plate and also for soft insulating materials. Fixing insulating materials for high re protection requirements (cellar ceiling insulation, insulation close to escape routes) FEATURES Easy installation by striking in, self-expanding No pre-drilling required for aerated concrete Easy installation CHARACTERISTIC VALUES Drill bit diameter ....................................................... 8 mm Hole depth t ........................................................ 60 mm Embedment depth hv ............................................... 50 mm Stress plate diameter .............................................. 35 mm NOTE The EJOT insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm. The insulation board fastening is carried-out according to DIN 18516-1.
R i vets
S peci a l screw s
S torm w a shers
mm
Anchor length L mm
Insulation thickness B mm 30 60 90 120 150 200 250 30 60 90 120 150 200 250
PU
Part number
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
80 110 140 170 200 250 300 80 110 140 170 200 250 300
250 250 250 250 250 200 200 250 250 250 250 250 200 200
DMH-8x80-V DMH-8x110-V DMH-8x140-V DMH-8x170-V DMH-8x200-V DMH-8x250-V DMH-8x300-V DMH-8x80-E DMH-8x110-E DMH-8x140-E DMH-8x170-E DMH-8x200-E DMH-8x250-E DMH-8x300-E
9700030301 9700030602 9700030603 9700030912 9700031215 9700031520 9700031300 9700030302 9700033603 9700036904 9700035912 9700035215 9700035520 9700035300
P ipe f lashings
Inst al l at i on to ol s
APPLICATION RANGE For xing soft insulating materials in combination with the EJOT DMH metal insulation support anchor Fixing soft insulating materials for high re protection requirements
PU
Part number
Acces sor ie s
250 250
DMT-80-V DMT-80-E
9700030156 9700030157
164
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Chemical anchors
PROCESSING AND CURING TIMES (dry substrate) Temperature C -10 -5 0 +5 +10 +20 +30 +35 Processing time Polyester Vinylester 90 min 90 min 45 min 25 min 25 min 15 min 15 min 6 min 6 min 4 min 4 min 2 min 2 min Curing time Polyester Vinylester 24 h 14 h 7h 120 min 120 min 80 min 80 min 45 min 45 min 25 min 25 min 20 min 20 min Masonry The temperature in the embedment area may amount to +50C, temporarily +80C Concrete The temperature in the embedment area may amount to +40C, temporarily +80C
PERMITTED LOADS PER EMBEDMENT Substrate Permitted loads max. Fperm. max. Fperm. kN kN Solid brick Mz 12 1.7 Solid lime sand brick KS 12 1.7 Vertically perforated brick HLz 4 0.3 0.6 1 Vertically perforated brick HLz 6 0.4 0.8 1 Vertically perforated brick HLz 12 0.8 1.0 1 Perforated lime sand brick KSL 4 0.4 0.6 1.2 Perforated lime sand brick KSL 6 0.6 0.8 1.2 Perforated lime sand brick KSL 12 0.8 1.4 1.2
Drill hole construction only with rotary drilling. For perforated lime sand brick the outer straps have to be at least 30 mm.
PERMITTED LOADS PER BRICK Stone format Maximum loads w/o extra w. extra load Fperm. load perm. kN kN 1.0 1.4 1.4 1.7 2.0 2.5
1 2
Bending moment Anchor rods M8 M 10 M 12 M 16 Mperm. in Nm Zinc-plated steel 5.8 10.7 21.4 37.4 95.1 A4 stainless steel 12.1 24.1 / 23.8* 42.1 106.7
1. Drill hole
3. Inject the right amount of composite mortar* (ll the sleeve completely)
1. Drill hole
3. Inject the right amount of composite mortar* (ll the hole up to 2/3)
165
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
3 DF 4 to 10 DF 10 DF
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
A n c h o r s a n d E m b e d m e n t Te c h n o l o g y Chemical anchors
S el f-dri l l i ng screw s
APPLICATION RANGE For embedment in Perforated brick masonry Solid brick masonry Concrete (VY 345 SF mortar cartridge, with approval) Concrete (PY 345 mortar cartridge, without approval) Natural stone (without approval) APPROVAL Z-21.3-1815 Z-21.3-1816 ETA-10/0134 NOTE Please observe the corresponding approvals during planning and processing. INCLUDED IN DELIVERY Incl. 2 MD mixing nozzles each Content mm 345 345 Composite mortar Vinyl resin (styrene and phthalate-free) Polyester resin PU 12 12 Price Order description / pcs. VY 345 SF mortar cartridge PY 345 mortar cartridge Part number 9571000345 9570000345
R i vets
S peci a l screw s
S torm w a shers
CONSUMPTION IN SOLID BUILDING MATERIALS* Anchor rod AST M8 x 110 AST M10 x 130 AST M12 x 160 AST M16 x 190 Drill hole Drill hole depth mm mm 10 80 12 90 14 110 18 125 Number of llings Resi Fix 345 54 33 20 11
*According to the ETA approval the drill hole has to be only 2/3 lled with the composite material. Experience has shown more is used and a lling of the complete drill hole has to be expected.
AMOUNT NEEDED IN PERFORATED BUILDING MATERIAL* Anchor rod AST M8 x 110 AST M10 x 130 AST M10 x 130 AST M12 x 160 AST M16 x 190 Mesh sleeve SH13-100 SH15-100 SH15-130 SH20-85 Drill hole Drill hole depth mm mm 14 105 16 105 16 135 16 135 20 90 Number of llings Resi Fix 345 20 15 12 12 11
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
FEATURES with nut and washer Steel quality 5.8 zinc-plated or A4 stainless steel APPROVAL Z-21.3-1815 Z-21.3-1816 ETA-10/0134 NOTE Please observe the corresponding approvals during planning and processing.
Thread
Length mm
Material
PU
Part number
Approved for polyester and vinyl ester composite mortar M8 110 20 Zinc plated steel 10 M8 110 20 A4 stainless steel 10 M10 130 30 Zinc plated steel 10 M10 130 30 A4 stainless steel 10 M12 160 35 Zinc plated steel 10 M12 160 35 A4 stainless steel 10 M16 190 45 Zinc plated steel 10 M16 190 45 A4 stainless steel 10 *for standard inst. depth in concrete
Inst al l at i on to ol s
AST M8x110-V AST M8x110-E AST M10x130-V AST M10x130-E AST M12x160-V AST M12x160-E AST M16x190-V AST M16x190-E
166
Acces sor ie s
APPLICATION RANGE In perforated brick masonry Nominal drill diameter d mm 14 16 16 20 *Part of the approval Hole depth t mm 105 105 135 90 suitable for Thread M8 M10 M8 - M12 M12 - M16 PU Price Order / 100 description pcs. SH13-100* SH15-100* SH15-130 SH20-85 Part number FEATURES Ensures exact calibration of threaded rod APPROVAL Z-21.3-1815 Z-21.3-1816 NOTE Please observe the corresponding approvals during planning and processing.
PU 1
MD mixer
20
MD
9570504192 FEATURES Suitable for VY 345 SF and PY 345 cartridges APPROVAL Z-21.3-1815 Z-21.3-1816 ETA-10/0134 NOTE Please observe the corresponding approvals during planning and processing.
167
Acces sor ie s
Inst al l at i on to ol s
PU
Part number
APPLICATION RANGE For the re-use of mortar cartridges after application of a new mixing nozzle
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
12 12 12 12
S torm w a shers
VSD
APPLICATION RANGE For fast and adhesive-free subsequent installation of curtain walls. For load-bearing shells made of concrete, solid brick and perforated brick FEATURES Building authorities approved anchor for subsequent installation of curtain walls Double expansion wall anchor: simultaneous embedment in load-bearing wall and outer leaf Clean and fast installation (no mortar required) Universal expansion zone: secure installation into concrete load-bearing shells, solid and perforated brick The use of A4 stainless steel screws guarantees corrosion protection 100% installation control Temperature-independent installation Can be installed at 0C APPROVAL Z-21.2-1652 TECHNICAL DATA Embedment depth hef ........................................... 70 mm Hole depth ts .................................................. Id + 10 mm Nominal drill diameter ............................................... 8 mm Minimum thickness of the outer leaf ....................... 115 mm Drive ......................................................... hexalobular T30 NOTE The EJOT VSD double expansion wall anchor enables the subsequent renovation of double-leaf masonry. Advanced corrosion or a complete lack of wire anchors can lead to decreased stability of the outer leaf and possibly cause considerable physical injury. In particular curtain walls made before 1979 should be subject to further inspection. When renovating the outer facade the stability of the curtain wall must be veried. The EJOT VSD is a very cost-effective solution for subsequent installation between load-bearing shell and outer leaf.
S torm w a shers
ef
z d
S peci a l screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
mm
Length ld mm
Distance az mm
PU
Part number
Anchor with A4 stainless steel screws (-E) 8 205 0 - 20 100 8 225 20 - 40 100 8 245 40 - 60 100 8 265 60 - 80 100 8 285 80 - 100 100 8 305 100 - 120 100
168
Acces sor ie s
Inst al l at i on to ol s
For riveting
EJOT RIVETING TOOL Electric riveting gun for blind rivet installation.
169
Acces sor ie s
Inst al l at i on to ol s
POWERFUL EJOT TOOLS Special screwdrivers and power drills for the installation of EJOT products.
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
EJOT INSTALLATION TOOLS EJOT installation tools for secure, fast and efcient fastening of EJOT Dabo screws with and without stress plates for xing insulation and roong menbranes to at roofs.
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
S torm w a shers
S peci a l screw s
Weight kg 1.75
R i vets
Accessories Order description Spare die Spare punch Price / Part number pcs. 9559974001 9559974002
170
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Accessories Order description Spare die Spare punch Punch guiding Allen key TORX T20 Price / Part number pcs. 9559984001 9559984002 9559984005 9559984015
171
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Application range up to mm Rivets: 5,0 Bulb-tite: 6,3 Rivets: 6,4 Bulb-tite: 7,7
Accessories Order description Rapid charger 14,4 V Li-Ion Quick exchange battery 1,3 Ah Quick exchange battery 2,6 Ah Chuck jaws (3-part set) Regular 17/24 nosepiece Regular 17/32 nosepiece Regular BT 17/32 nosepiece Regular BT 17/48 nosepiece Retainer nosepiece 17/24 R Retainer nosepiece 17/29 R Articulated jointed nosepiece 17/29 Articulated jointed nosepiece 17/29 Articulated jointed nosepiece 17/32 Application range Price / Part number pcs. 9150481203 9150481202 9150481204 9150481110 9150481115 9150481118 9150481106 9150481113 9150481121 9150481105 9150481162 9150481163 9150481164
P ipe f lashings
Rivets 4,0 mm Rivets 4,8 mm Bulb-tite 5,2 mm Bulb-tite 7,7 mm Rivets 4,0 mm Rivets 4,8 mm Rivets 4,8 mm Rivets 4,8 mm K14 Rivets 5,2 mm
172
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Weight kg 23.0
Accessories Order description Bit H2 - 1/4 x 30 Spray oil 100 ml Socket A/F 8 - 1/4" x 30 Transport box Tool kit Price / Part number pcs. 9150006000 9150911000 9150315001 9151106000 9151104000
173
Acces sor ie s
Inst al l at i on to ol s
page 134 page 134 page 129 page 128 page 130 page 133
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
P ipe f lashings
Weight kg 28.0
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Accessories Order description page 134 page 134 page 129 page 128 page 130 page 133 Bit H2 - 1/4 x 30 Spray oil 100 ml Socket A/F 8 - 1/4" x 30 Transport box Tool kit Price / Part number pcs. 9150006000 9150911000 9150315001 9151106000 9151104000
174
Acces sor ie s
Inst al l at i on to ol s
Accessories Order description Bit H2 - M6 x 35 Transport box Price / Part number pcs. 9250612000 9151506000
175
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
Weight kg 3.2
176
Acces sor ie s
Inst al l at i on to ol s
Weight kg
177
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Weight kg 1.8
178
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Installation tools Power tools Cordless hammer drill DCD 985 L2K
18,0 Volt FEATURES 3 shift full metal gear with precise torque rate for optimum work progress Very efficient and sturdy high-performance motor with safety electronics Optimal rotation speed / torque ratio for extreme heavy duty drilling and fastening Unproblematic long-term use through safety electronics (continuous monitoring of battery temperature, current drain and discharge protection) Very compact and balanced design as well as rubber covered, ergonomic handle for safety and work comfort 13 mm full metal quick-release chuck and automated spindle lock Easily adjusted switch electronic for exact tapping and precise fastening Integrated LED light 2 Premium lithium system batteries with long service life TECHNICAL DATA Battery .................................................... 18,0 Volt / 3,0 Ah Power output........................................................ 500 Watt Idle speed .......................... 0-575 / 0-1.350 / 0-2.000 min-1 Idle hammer speed ...... 0-9.755 / 0-22.950 / 0-34.000 min-1 Consistent torque .................................................... 55 Nm Max. drilling performance in wood / metal / stone.. 50 / 13 / 16 mm Drill chuck spread ..............................................1,5-13 mm Weight (incl. battery) ................................................. 2,4 kg INCLUDED IN DELIVERY 1 x 60 Min. fast battery recharger 2 x 3,0 Ah Li-Ion rechargeable battery 1 belt clip 1 bit holder 1 transport box
S el f-dri l l i ng screw s
2.4
9150210000
179
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Weight kg
R i vets
S peci a l screw s
S torm w a shers
R i vets
S peci a l screw s
S torm w a shers
Accessories Order description K8-1/4"x50 socket Price / Part number pcs. 9250705101
180
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Weight kg 2.0
Accessories Order description Socket SW8 - 1/4" x 25 Nosepiece Long screw support SH2 incl. socket holder 2 and SW8 socket Price / Part number pcs. 9150315000 9151701029 9150508111
181
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
Installation tools To o l s
S el f-dri l l i ng screw s
mm Form S 4.0 4.1 4.5 4.5 4.5 4.5 4.5 5.0 5.0 5.0 5.0 5.0 5.0 5.1 5.3 5.3 5.3 5.3 5.3 5.3 5.3 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.8 5.8 5.8 5.8 6.8 6.8 6.8 7.0 7.0 7.0 7.0 7.2 7.2 7.2 7.2 7.4 7.4 7.4
Length mm
Part number
S torm w a shers
182
Acces sor ie s
60 55 60 125 175 235 295 60 95 125 175 220 250 62 60 95 125 175 220 250 290 65 95 125 175 220 250 290 65 95 125 170 220 250 290 95 180 260 300 75 175 225 75 125 175 225 75 125 175 225 125 175 225
1000 1000 900 900 900 900 900 900 900 900 900 900 900 900 800 800 800 800 800 800 800 750 750 750 750 750 750 750 700 700 700 700 700 700 700 700 700 700 700 600 600 600 600 600 600 600 600 600 600 600 600 600 600
S 4,0/60 drill bit S 4,1/55 drill bit S 4,5/60 drill bit S 4,5/125 drill bit S 4,5/175 drill bit Bohrer S 4,5/235 S 4,5/295 drill bit S 5,0/60 drill bit S 5,0/95 drill bit S 5,0/125 drill bit S 5,0/175 drill bit S 5,0/220 drill bit S 5,0/250 drill bit S 5,1/62 drill bit S 5,3/60 drill bit S 5,3/95 drill bit S 5,3/125 drill bit S 5,3/175 drill bit S 5,3/220 drill bit S 5,3/250 drill bit S 5,3/290 drill bit S 5,3/65 drill bit S 5,5/95 drill bit S 5,5/125 drill bit S 5,5/175 drill bit S 5,5/220 drill bit S 5,5/250 drill bit S 5,5/290 drill bit S 5,7/65 drill bit S 5,7/95 drill bit S 5,7/125 drill bit S 5,7/170 drill bit S 5,7/220 drill bit S 5,7/250 drill bit S 5,7/290 drill bit S 5,8/95 drill bit S 5,8/180 drill bit S 5,8/260 drill bit S 5,8/300 drill bit S 6,8/75 drill bit S 6,8/175 drill bit S 6,8/225 drill bit S 7,0/75 drill bit S 7,0/125 drill bit S 7,0/175 drill bit S 7,0/225 drill bit S 7,2/75 drill bit S 7,2/125 drill bit S 7,2/175 drill bit S 7,2/225 drill bit S 7,4/125 drill bit S 7,4/175 drill bit S 7,4/225 drill bit
9250407000 9250405000 9250434000 9250435000 9250436000 9250450235 9250450295 9250409000 9250410000 9250411000 9250412000 9250413000 9250414000 9250439000 9250415000 9250416000 9250417000 9250418000 9250419000 9250437000 9250438000 9250420000 9250421000 9250422000 9250408000 9250423000 9250492000 9250424000 9250425000 9250426000 9250427000 9250428000 9250429000 9250432000 9250433000 9250441000 9250580180 9250580260 9250580300 9250430000 9250680175 9250510000 9250440000 9250499000 9250500000 9250493000 9250442000 9250504000 9250505000 9250494000 9250506000 9250507000 9250497000
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
Length mm
Part number
45 50 55 55 60 62 62
D 3,0/45 drill bit D 3,5/55 drill bit D 4,0/55 drill bit D 4,2/55 drill bit D 4,5/60 drill bit Bohrer D 5,0/62 D 5,3/62 drill bit
mm 4.25 4.5 4.6 5.3 5.4 5.4 5.6 5.7 5.8 5.8 5.8
Rotation speed Price / pcs. Order description rpm 450 400 400 350 350 350 350 390 350 350 350 HSCO 4,25/55 HSCO 4,5/126 HSCO 4,6/58 HSCO 5,3/86 HSCO 5,4/66 HSCO 5,4/93 HSCO 5,6/66 HSCO 5,7/66 HSCO 5,8/66 HSCO 5,8/93 HSCO 5,8/139
183
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S torm w a shers
Installation tools To o l s
S el f-dri l l i ng screw s
S peci a l screw s
S torm w a shers
R i vets
184
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
mm 5 5 5 6 6 6 6 8 8 8 8 8 8 10 10 10 10 10
Effective length mm 50 100 150 50 100 150 200 50 100 150 200 250 400 100 150 200 250 400
Total length mm 110 160 210 110 160 210 260 110 160 210 260 310 460 160 210 260 310 460
Price Order description / pcs. 4 edge SDS-plus 5x110 4 edge SDS-plus 5x160 4 edge SDS-plus 5x210 4 edge SDS-plus 6x110 4 edge SDS-plus 6x160 4 edge SDS-plus 6x210 4 edge SDS-plus 6x260 4 edge SDS-plus 8x110 4 edge SDS-plus 8x160 4 edge SDS-plus 8x210 4 edge SDS-plus 8x260 4 edge SDS-plus 8x310 4 edge SDS-plus 8x460 4 edge SDS-plus 10x160 4 edge SDS-plus 10x210 4 edge SDS-plus 10x260 4 edge SDS-plus 10x310 4 edge SDS-plus 10x460
Part number 9210005110 9210005160 9210005210 9210006110 9210006160 9210006210 9210006260 9210008110 9210008160 9210008210 9210008260 9210008310 9210008460 9210010160 9210010210 9210010260 9210010310 9210010460
185
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
Installation tools To o l s
S el f-dri l l i ng screw s
Part number 9250473000 9250474000 9250709000 9200000110 9200000127 9200000152 9200000029 9200000200 9200000300
R i vets
S peci a l screw s
S torm w a shers
Bit TORX
FEATURES External hexagon drive as per DIN 3126 TECHNICAL DATA Drive ................. external hexagon head drive 1/4 6,3 mm Type and size Price Order description / pcs.
Description Length mm
Part number 9150010000 9150008000 9150009000 9150003000 9250431000 9250431002 9150011000 9250431001 9253014200 9253014250 9250480000 9250140110 9250140152 9250251425 9250251430
P ipe f lashings
T20 C 25 TORX T20-1/4/Cx25 T20W C 25 TORX T20W-1/4/Cx25* T25 C 25 TORX T25-1/4/Cx25 T25W C 25 TORX T25W-1/4/Cx25* T30 C 25 TORX T30-1/4/Cx25 T30W C 25 TORX T30W-1/4/Cx25* T25 E 70 TORX T25-1/4/x70 T30 E 50 TORX T30-1/4/Ex50 T30 E 200 TORX T30-1/4/x200 T30 E 250 TORX T30-1/4/x250 T40 C 25 TORX T40-1/4/Cx25 T25 E 110 TORX T25-1/4/ x110 T25 E 152 TORX T25-1/4/ x152 T25 M6 33 TORX T25-M6/x33 T30 M6 33 TORX T30-M6/x33 * special bit: conical design for force t at screw head
186
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
9151600000
Accessories Order description FR-Bit TX 25/70 Depth control sleeve for DAM 5 special screwgun Price / Part number pcs. 9150011000 -
EJOT FR-variotool
APPLICATION RANGE For reliable fixing of corrugated and trapezoidal proles with FR screws without sealing washers! ADVANTAGES For efficient fixing of corrugated and trapezoidal profiles Fastener does not buckle to the side FEATURES Easy to handle Optimum installation in any position Reliable screw guidance Captive
9151630000
Accessories Order description FR-Bit T 25/70 Price / Part number pcs. 9151600009
187
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
Installation tools To o l s
S el f-dri l l i ng screw s
Socket 1/4
FEATURES Drive acc. to DIN 3126 Form E TECHNICAL DATA Drive ......................... external hexagon head 1/4 6,3 mm
Wrench size Clamping socket A/F 8 A/F 3/8 A/F 8 A/F 3/8 socket A/F 8 A/F 13 A/F 10 A/F 8 A/F 13 A/F 3/8 Magnetic socket A/F 7 A/F 8 A/F 8 A/F 7
Length mm
Price / Order description 100 pcs. K-8-1/4"x50 socket K-3/8-1/4"x50 socket K-8-1/4"x65 socket K-3/8-1/4"x65 socket S-8-1/4"x50 socket S-13-1/4"x50 socket S-10/8-1/4"x50 socket S-8-1/4"x65 socket S-13-1/4"x65 socket S-3/8-1/4"x65 socket M-7-1/4"x50 socket M-8-1/4"x50 socket M-8-1/4"x65 socket M-7-1/4"x65 socket
Part number
S torm w a shers
50 50 65 65 50 50 50 65 65 65 50 50 65 65
9250705101 9250706002 9250502100 9250489100 9250705001 9250719000 9250707000 9250502000 9250720000 9250489000 9250704000 9250705000 9250488000 9250487000
P ipe f lashings
R i vets
S peci a l screw s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
Length mm 42 57
188
Acces sor ie s
Inst al l at i on to ol s
Wrench size Clamping socket A/F 3/8 A/F 8 socket A/F 8 A/F 10 Magnetic socket A/F 13 A/F 7 A/F 8
Length mm
Price / Order description 100 pcs. K-3/8-5/16"x65 socket K-8-5/16"x65 socket S-8-5/16"x65 socket S-10-5/16"x65 socket M-13-5/16"x65 socket M-7-5/16"x65 socket M-8-5/16"x65 socket
Part number
65 65 65 65 65 65 65
Length mm 45
189
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
FEATURES Internal hexagon acc. to DIN 3126 Form E Drive acc. to DIN 3126 Form E
R i vets
S peci a l screw s
S torm w a shers
Installation tools To o l s
S el f-dri l l i ng screw s
S torm w a shers
R i vets
S peci a l screw s
Blow-out pump
EJOT VACUtest
APPLICATION RANGE For seal testing of screw and rivet connections on roofs and walls ADVANTAGES Easy to handle Quick and accurate seal-testing of connections Minimal technical effort FEATURES For screw and rivet connections on smooth airtight surfaces INCLUDED IN DELIVERY 1 handpump with manometer and tube 2 nosepiece 1 operating manual 1 transport box
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
190
Acces sor ie s
Inst al l at i on to ol s
Accessories
Part number 3010092300 3010009300 3010077300 3010011300 3010067300 3010066300 3010013300 3010014300 3010015300 ADVANTAGES: Waterproofing Improve the static and dynamic values Excellent weather- and UV-resistance. FEATURES A2 stainless steel 1 mm metal back Sealing EPDM
6.9 6.9
4.0 4.0
3010038300 3010091300
ADVANTAGES: Waterproofing Improve the static and dynamic values Excellent weather- and UV-resistance. FEATURES A2 stainless steel 1.8 mm metal back Sealing EPDM Sealing washer to cover misdrills
internal mm 6.3
ange mm 9.0
Height mm 7.0
FEATURES A2 stainless steel 1 mm metal back Moulded EPDM part Pre-assembled on EJOT screws for JZ3, JA3, JZ2 and JA2
191
Acces sor ie s
Inst al l at i on to ol s
external mm 25.0
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
internal mm
Elastomer thickness mm
Part number
R i vets
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Accessories
S el f-dri l l i ng screw s
PU 250
S peci a l screw s
S torm w a shers
R i vets
1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000
8200010700 8200011700 8200012700 8200013700 8200043700 8200014700 8200015700 8200020700 8200021700 8200022700 8200023700 8200053700 8200054700 8200024700 8200025700
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Screw JT...-2-4,2 JF...-2H-4,8 JT...-2H-4,8 JT...-2-4,8 Dabo ...-4,8 Dabo ...-4,8 JT...-3-4,8 JT...-2H-5,5 JT...-2H-Plus-5,5 JT...-3H-5,5 JT...-3-5,5 JT...-4-5,5 JT...-6-5,5 JT...-8-5,5 JT...-2H-6,3 JT...-3H-6,3 JT...-4-6,3 JT...-6-6,3 JT...-X-6,0 JZ...-6,3 JA...-6,5
Thread protection sleeve 3,0x10 3,0x10 3,0x10 3,0x10 4,5x25 4,5x35 3,5x10 3,5x10 4,0x10 4,0x10 4,0x10 4,5x10 4,5x10 4,5x10 3,5x10 4,5x10 4,5x10 5,0x10 5,5x10 5,5x10 5,5x10
192
Acces sor ie s
Inst al l at i on to ol s
Accessories
PU
Part number*
SDF-KB SDP-KB 14 SDF-KB SDP-KB 8 JZ3 JA3 JT3 JZ3 JA3 SDF-KB SDP-KB 10 JZ3 JA3
26 16 14 16 14 16 19 22 19 22 25 29
A/F 17 A/F 10 A/F 3/8 A/F 8 A/F 3/8 A/F 13 A/F 3/8
20 20 28 28 34
Push-on cap 22-17 Push-on cap 16-10 Push-on cap 16-3/8 Push-on cap 16-8 Push-on cap 22-3/8 Push-on cap 22-13 Push-on cap 29-3/8
193
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
S torm w a shers
External mm
S el f-dri l l i ng screw s
Accessories
S el f-dri l l i ng screw s
Push-on cap mm
PU
Price / Order description 100 pcs. Push-on cap T30 Push-on cap T40
S peci a l screw s
S torm w a shers
R i vets
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
EJOT AS spacer
APPLICATION RANGE To compensate for tolerances on wall and roof AS-30 as installation aid for the EJOT at roong anchor FDD-50 FEATURES Plastics All-purpose for anchor diameters of 8 mm and 10 mm Easy installation through clipping-on from the side Variable combinations TECHNICAL DATA Dimension ...................................................... 50 x 50 mm CROSS REFERENCE Flat roong anchor FDD-50 ...................... page 138 Thickness mm 3 5 8 10 15 30 PU 100 100 100 100 100 100
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
Price / Order description 100 pcs. AS-3 AS-5 AS-8 AS-10 AS-15 AS-30
194
Acces sor ie s
Inst al l at i on to ol s
RUINE HAUS WEITMAR, BOCHUM, GERMANY Supplied by EJOT: EJOT SUPER-SAPHIR self-drilling screw JT4
Accessories Notes
Konvortec
R i vets
195
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
S peci a l screw s
S torm w a shers
S el f-dri l l i ng screw s
Contact International
S el f-dri l l i ng screw s
AUSTRIA EJOT Austria GmbH & Co KG Grazer Vorstadt 146 A-8570 Voitsberg phone: +43 3142 2 76 00-0 fax: +43 3142 2 76 00-30 e-mail: info@ejot.at Internet: www.ejot.at BALTIC STATES UAB EJOT Baltic Titnago g. 19 LT-02300 Vilnius phone: +370 5 23 11-437 fax: +370 5 23 11-439 e-mail: info@ejot.lt Internet: www.ejot.lt BENELUX EJOT Benelux bvba/sprl Reedonk 19-1 B-2880 Bornem phone: +32 3 740 79 70 fax: +32 3 740 79 79 e-mail: info@ejot.be Internet: www.ejot.be BULGARIA EJOT Bulgaria EOOD & Co. KD Logistic center Mimi DM No 31 Miroviane 1289 phone: +359 2421 96 37 fax: +359 2421 96 37 e-mail: mail@ejot.bg BOSNIA AND HERZEGOVINA EJOT d.o.o. Sarajevo Rajlovacka b.b. BiH-71000 Sarajevo phone: +387 33 769 275 fax: +387 33 769 276 e-mail: info@ejot.ba CHINA EJOT Fastening Systems (Taicang) Co., Ltd. No. 88,Zhenghe Road (East) Economic Development Zone, Taicang, Jiangsu Prov. Postcode: 215413, PR China phone: +86 512 53 56 52 90 fax: +86 512 53 56 62 92 e-mail: info@ejot.cn Internet: www.ejot.cn CROATIA EJOT Spojna Tehnika d.o.o. Franje Luia 23/3 HR-10090 Zagreb phone: +385 1 349 86 12 fax: +385 1 349 89 63 e-mail: ejot@ejot.hr CZECH REPUBLIC EJOT CZ, s.r.o. Zdbradsk 65 CZ-25101 iany-Jalovice phone: +420 323 63 78 11 fax: +420 323 63 78 18 e-mail: info@ejot.cz Internet: www.ejot.cz
DENMARK EJOT Danmark ApS Industrisvinget 8 DK-4683 Rnnede phone: +45 56 39 08 42 fax: +45 56 39 91 06 e-mail: info@ejot.dk Internet: www.ejot.dk FRANCE EJOT France S.A.R.L. Z.l. rue du Climont F-67220 Vill phone: +33 388 58 92 00 fax: +33 388 58 92 01 e-mail: info@ejot.fr Internet: www.ejot.fr GERMANY EJOT Building Fasteners In der Stockwiese 35 57334 Bad Laasphe, Germany phone: +49 2752 908-0 fax: +49 2752 908-707 e-mail: bau@ejot.de Internet: www.ejot.de HUNGARY EJOT Hungria Kft. csai t 1-3 H-1239 Budapest phone: +36 1 289 30 90 fax: +36 1 289 30 91 e-mail: ejot@ejot.hu Internet: www.ejot.hu ITALY EJOT Tecnologie di ssaggio S.a.s. Via Pigafetta I-35011 Campodarsego (PD) e-mail: info@ejot.it Internet: www.ejot.it MEXICO EJOT ATF Fasteners de Mxico y Compaia, S. en C. Avenida Del Siglo 180 Parque Industrial Millenium San Luis Potosi S.L.P. 78395, Mxico phone: +52 444 870 82 00 Internet: www.ejot-atf.com NORWAY EJOT Festesystem A/S Aslakveien 20A N-0701 Oslo phone: +47 23 25 30 40 fax: +47 23 25 30 41 e-mail: festesystem@ejot.no Internet: www.ejot.no POLAND EJOT Polska Spka z ograniczon odpowiedzialnoci Spka komandyto Ul. Jeowska 9 PL-42-793 Ciasna phone: +48 34 351 06 60 fax: +47 23 353 54 10 e-mail: ejot@ejot.pl Internet: www.ejot.pl
ROMANIA EJOT Romania SRL Str. Depozitelor 27 RO-110078 Pitesti phone: +40 248 223 886 fax: +40 248 223 886 e-mail: info@ejot.ro RUSSIA OOO EJOT Wostok 107497 Moscow, Russia ul. Amurskaya 5, bld. 7 phone: +7 495 941 95 84 fax: +7 495 941 95 84 e-mail: info@ejot.ru Internet: www.ejot.ru SERBIA EJOT Tehnika spajanja d.o.o. Autoput Beograd-Novi Sad 296X SCG-Serbia, 11080 Zemun phone: +381 11 848 60 82 fax: +381 11 848 60 82 e-mail: info@ejot.rs SLOVAKIA EJOT Slovakia, s.r.o. Juzn trieda 82 (Arel VSS) SK-04001 Koice phone: +421 55 622 17 60 fax: +421 55 678 09 57 e-mail: info@ejot.sk Internet: www.ejot.sk SPAIN EJOT Ibrica S. L. Pol. P 29 - C/ Azuela 78, nave 4 E-28400 Collado Villalba (Madrid) phone: +34 91 286 10 20 fax: +34 91 286 10 21 e-mail: info@ejot.es Internet: www.ejot.es SWEDEN EJOT & AVDEL System AB Santagsvgen 9 S-70236 rebro phone: +46 19 20 65 00 fax: +46 19 20 65 14 e-mail: info@ejot-avdel.se Internet: www.ejot-avdel.se SWITZERLAND EJOT Schweiz AG Uttwiler Strae 3 CH-8582 Dozwil phone: +41 71 414 52 22 fax: +41 71 414 52 50 e-mail: info@ejot.ch Internet: www.ejot.ch TAIWAN EJOT Taiwan Branch 4F, 248-17 Sin Sheng Rd.,Chien Cheng Distr. 806 Kaosiung, Taiwan R.O.C. phone: +886 7 811 08 18 e-mail: ithiel@ejot.de
TURKEY EJOT Tezmak Cebeci Cad. No. 84 TR-34440 Kkky-Istanbul phone: +90 212 538 00 01 fax: +90 212 538 00 93 e-mail: info@ejot-tezmak.com Internet: www.ejot-tezmak.com UNITED ARAB EMIRATES EJOT Middle East FZE Sharjah Airport International Freezone P.O. Box 120588 Sharjah United Arab Emirates phone: +971 6 557 97-70 fax: +971 6 557 97-75 e-mail: mexner@ejot.ae Internet: www.ejot.ae UNITED KINGDOM EJOT U.K. Ltd. Hurricane Close Sherburn Enterprise Park Sherburn-in-Elmet GB-Leeds LS25 6PB phone: +44 1977 68 70 40 fax: +44 1977 68 70 41 e-mail: info@ejot.co.uk Internet: www.ejot.co.uk USA ASYST TECHNOLOGIES, LLC 5811 99th Avenue Kenosha, Wi 53144 USA phone: +1 262 8 57 22 44 e-mail: imefe@asysttech.com Internet: www.asysttech.com
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
www.globalfasteneralliance.com
Acces sor ie s
For all other countries please contact our German ofce directly, EJOT Building Fasteners GmbH.
196
Contact Notes
BIOMASS HEATING POWER PLANT AND WOOD PELLETS PRODUCTION, GERMANY Supplied by EJOT: EJOT SUPER-SAPHIR self-drilling screw JT3, EJOT Dabo screws
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo P ipe f lashings S caf f olding fast ener s D ir ect Fast ening Fa steni ng S yst . for S ol a r Insta l l a ti os R i vets S peci a l screw s S torm w a shers S el f-ta ppi ng screw s S el f-dri l l i ng screw s
197
Acces sor ie s
Inst al l at i on to ol s
Index
S el f-dri l l i ng screw s
A Accessories .................................. 191 Accubird riveting tool ..................... 172 Aerated concrete screw FPS-E-8,0.. 140 Anchor (see anchor bolt, scaffolding anchor) Anchor bolt S-KA ........................... 160 Anchor bolt S-KAH ......................... 161 Anchor rod Resi AST ...................... 166 Applicator gun APVM ..................... 167 Approvals ....................................... 14 AS spacer ..................................... 194 B Bi-met screw (see self-drilling screw JT3) Bit cross-recess ............................ 186 Bit holder BT 1/4 .......................... 188 Bit holder BT 5/16 ........................ 189 Bit TORX ..................................... 186 Blind rivet AL/E-4,8........................ 102 Blind rivet AL/V-4,8........................ 102 Blind rivet K14-AL/E....................... 102 Blow-out pump.............................. 190 BOP electric screwgun 10-2 ........... 177 Bulbtite rivet.................................. 104 C Cartridges 6,3/16 .......................... 111 Case-hardened self-drilling steel screw (see self-drilling screw JT2) Cavity wall repair anchor VSD .......... 168 Chemical anchors .......................... 165 Chip board screw SH2-5,0 ............... 97 Chip board screw SH3-5,0 ............... 97 Chip board screw SH3-S-4,0 ............ 98 Chip board screw SH3-S-4,5 ............ 98 Chip board screw SH3-S-5,0 ............ 98 Climadur (Denition) ........................ 26 Closed-end rivet AL/E-4,8 .............. 103 Closed-end rivet AL/V-4,8 .............. 103 Concrete screw FBS-R-6,3 ............. 139 Cordless hammer drill DCD 985 L2K 179 Cordless screwgun DCD 780 L2K ... 178 Corremaks .................................... 82 CRONIMAKS.................................. 83 D Dabo (see at roong screw) DEKTITE ..................................... 116 DH insulation support anchor .......... 163 Direct fastening ............................. 109 DMH metal insulation support anchor.......................................... 164 DMT metal insulation stress plate .... 164 Drill bits ........................................ 182 Drive rivet AL/E-4,8 ....................... 104 E ECOset installation tool................... 173 ECOset HTK installation tool ........... 175 ECOset L installation tool ................ 174 EJOFAST (see side lap screw) EJOPLAST .................................... 124 EJOPLAST joint sealant .................. 124 European technical approvals ........... 15 F Facade anchor SDF-KB-8 ............... 149 Facade anchor SDF-KB-10H ........... 147 Facade anchor SDF-KB-10L ........... 151
Facade anchor SDF-KB-10V ........... 145 Facade anchor SDF-S-8 ................. 148 Facade anchor SDF-S-10H ............. 146 Facade anchor SDF-S-10V ............. 144 Facade anchor SDP-KB-10S ........... 155 Facade anchor SDP-KB-14 ............. 157 Facade anchor SDP-S-10S ............. 154 Facade anchor SDP-S-14 ............... 156 Fibre cement screw (see self-drilling screw JT2-FZ-/JT4-FZ-) Flat roong installation tool ............. 173 Flat roong anchor FDD-50 ............ 138 Flat roong screw A/F 8 R-4,8......... 128 Flat roong screw A/F 8 RT-4,8 ....... 129 Flat roong screw TKE-4,8.............. 133 Flat roong screw TKR-3-4,8 .......... 131 Flat roong screw TKR-4,8 ............. 130 Flat roong screw VHT-R-4,8 .......... 132 FR-tool ........................................ 187 FR-variotool ................................. 187 G GU ring bolt M14 ........................... 115 GU threaded sleeve ....................... 115 H Hammer drill ................................. 179 Hammer drill bit SDS-plus .............. 184 Hand gun ..................................... 124 Hose clamp ................................... 123 HSBR tie pin 14 ............................. 111 I Information ....................................... 8 Installation aid ............................... 194 Installation tools ............................ 169 International contact ...................... 196 M Manual installation tool HSK-HTK .... 176 Manual pump VACUtest .................. 190 MD mixer ...................................... 167 Mushroom washer ........................ 191 N Nail anchor ND-K -6 ....................... 162 Nail anchor ND-K-8 ....................... 162 Nibbler ......................................... 170 O ORKAN storm washer corrugated ...... 87 ORKAN storm washer trapezoidal ...... 86 P Pipe ashings Combo..................... 117 Pipe ashings Ezi-Seal ................... 119 Pipe ashings Retrot .................... 121 Pipe ashings Soaker ..................... 120 Pipe ashings Square..................... 118 Pipe ashings Strip Flash................ 122 Powerbird riveting tool ................... 172 Precision drill bit HSCO................... 183 Precision drill bit HSS form D .......... 183 Precision drill bit HSS form S ........... 182 PT screw type DG 40 .................... 100 PT screw type DG 40-Z .................. 99 PT screw type DG 50 .................... 100 PT screw type DG 50-Z .................. 99 PT screw type DG 55-C .................. 99 Push-on cap hexagon RAL .............. 193 Push-on cap TORX ....................... 194 R Renovation anchor ......................... 168
Repair screw JB3-7,2 ...................... 93 ResiFix mortar cartridge ................. 166 Ring bolt M10 ............................... 113 Rivets ........................................... 102 S Sandwich screw (see self-drilling screw JT2-D-/JT3-D-) Scaffolding anchor JA3-GT-6,5 ....... 113 Scaffolding anchor JA3-GU-6,5 ...... 114 Scaffolding anchor JZ3-GT-6,3 ....... 113 Scaffolding anchor JZ3-GU-6,3 ...... 114 Sealing washer E ........................... 191 Sealing washer ES ......................... 191 Self-drilling screw JT2-2-4,2 ............ 38 Self-drilling screw JT2-2-4,9 ............ 40 Self-drilling screw JT2-2-6,5 ............ 41 Self-drilling screw JT2-2H/3-4,8....... 39 Self-drilling screw JT2-2H-4,8.......... 39 Self-drilling screw JT2-2H-5,5.......... 40 Self-drilling screw JT2-2H-6,3.......... 41 Self-drilling screw JT2-3-4,8 ............ 42 Self-drilling screw JT2-3-5,5 ............ 42 Self-drilling screw JT2-3H-5,5.......... 43 Self-drilling screw JT2-3H-6,3.......... 43 Self-drilling screw JT2-6-5,5 ............ 44 Self-drilling screw JT2-6-6,3 ............ 44 Self-drilling screw JT2-8-5,5 ............ 45 Self-drilling screw JT2-12-5,5 .......... 45 Self-drilling screw JT2-12-6,3 .......... 46 Self-drill. screw JT2-D-6H-5,5/6,3.... 47 Self-drill. screw JT2-D-12H-5,5/6,3.. 48 Self-drilling screw JT2-FZ-6-6,3 ....... 49 Self-drilling screw JT2-FZ-12-6,3 ..... 50 Self-drilling screw JT2-FZ-F-6,5 ....... 51 Self-drilling screw JT2-ST-2-6,0 ....... 51 Self-drilling screw JT3-2-4,9 ............ 54 Self-drilling screw JT3-2-5,6 ............ 57 Self-drilling screw JT3-2-6,0 ............ 57 Self-drilling screw JT3-2-6,5 ............ 58 Self-drilling screw JT3-2H-4,8.......... 53 Self-drilling screw JT3-2H-Plus-5,5 .. 55 Self-drilling screw JT3-3-5,5 ............ 59 Self-drilling screw JT3-6-5,5 ............ 60 Self-drilling screw JT3-6-6,3 ............ 61 Self-drilling screw JT3-12-5,5 .......... 62 Self-drill. screw JT3-D-6H-5,5/6,3.... 64 Self-drill. screw JT3-D-12H-5,5/6,3.. 65 Self-drilling screw JT3-FR-12-5,5..... 63 Self-drilling screw JT3-FR-2-4,9....... 55 Self-drilling screw JT3-FR-2H-4,8 .... 54 Self-drill. screw JT3-FR-2H-Plus-5,5 56 Self-drilling screw JT3-FR-3-5,5....... 59 Self-drilling screw JT3-FR-6-5,5....... 61 Self-drilling screw JT3-ST-2-6,0 ....... 66 Self-drilling screw JT3-X-2-6,0 ........ 66 Self-drilling screw JT4-2-4,8 ............ 67 Self-drilling screw JT4-3H/5,5,5 ....... 69 Self-drilling screw JT4-4-4,8 ............ 69 Self-drilling screw JT4-6-5,5 ............ 71 Self-drilling screw JT4-FR-2-4,9....... 68 Self-drilling screw JT4-FR-2H-4,8 .... 67 Self-drilling screw JT4-FR-4-4,8....... 70 Self-drilling screw JT4-FR-4-5,5....... 71 Self-drilling screw JT4-FZ-6,5 .......... 72 Self-drilling screw JT4-S-2-4,8 ........ 73 Self-drilling screw JT4-STS-3-4,8..... 73
Self-drilling screw JT4-ZT-3-4,2 ....... 68 Self-drilling screw JT4-ZT-4-4,8 ....... 70 Self-tapping screw BS-R-6,3 ............ 90 Self-tapping screw Duro PT .............. 95 Self-tapping screw JA1-6,5 .............. 82 Self-tapping screw JA2-6,5 .............. 76 Self-tapping screw JA3-6,5 .............. 78 Self-tapping screw JA3-FR-4,9......... 91 Self-tapping screw JA3-LT-4,9 ......... 91 Self-tapping screw JA3-S-6,5 .......... 92 Self-tapping screw JA3-ZT-6,5 ......... 92 Self-tapping screw JB3-ZT-6,3 ......... 93 Self-tapping screw JZ1-6,3 .............. 82 Self-tapping screw JZ2-6,3 .............. 76 Self-tapping screw JZ3-6,3 .............. 80 Self-tapping screw JZ3-8,0 .............. 95 Self-tapping screw JZ3-S-6,3........... 94 Self-tapping screw JZ3-ZT-6,3 ......... 94 Self-tapping screw JZ7-6,3 .............. 83 Shearing load washer VS ................ 192 SH mesh sleeves ........................... 167 Shot ring tool P 525 L ................... 109 Shot ring tool P 560 ..................... 110 Side lap screw JF2-2H-4,8 ............... 38 Side lap screw JF3-2H-4,8 ............... 53 Socket 1/4 .................................. 188 Socket 5/6 .................................. 189 Solar Fastening System JA3-SB ...... 107 Solar Fastening System JZ3-SB ...... 107 Special nibbler KN 1.3 T ................. 170 Special screwgun DAM5 ................ 180 Special screwgun DAM5-SH2 ......... 181 Special screws ................................ 90 Stainless steel self-drilling screw (see self-drilling screw JT4) Standing seam system screw ............ 66 Steel anchor (see anchor bolt, scaffolding anchor) Storm washer .................................. 85 Stress plate Eco Tek 50 .................. 136 Stress plate HTK 50 ....................... 136 Stress plate HTK-M ........................ 137 Stress plate HTV 82/40 .................. 134 Stress plate HTV 82/40 F................ 135 Stress plate HTV 82/40 TK .............. 134 Stress plate HTV RU ....................... 135 T Test certicates ............................... 14 Thread protection sleeve ................ 192 Tie pin HSBR 14 ............................ 111 Tools ............................................ 182 U Universal drill bit SDS-plus.............. 184 Universal facade anchor SDF-KB-14U ................................. 153 Universal facade anchor SDF-S-10U ................................... 150 Universal facade anchor SDF-S-14U ................................... 152 Universal hose clamp ..................... 123 Universal nibbler KN 2.0 L .............. 171 V VACUtest ...................................... 190 VSD cavity wall repair anchor .......... 168
198
Acces sor ie s
Inst al l at i on to ol s
St res s p la tes/ Fla t ro of ing fla t roof ing Sel f-d rilling a nch ors scr ews D abo
P ipe f lashings
R i vets
S peci a l screw s
S torm w a shers
365-GB/1.5/12.11