Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
xix xix xx
Objectives Organization
Related Documentation xxiv Cisco ASR 1000 Series Routers Documentation Conventions
xxv
xxiv
Obtaining Documentation and Submitting a Service Request Software Packaging and Architecture
1
xxvi
Software Packaging on the Cisco ASR 1000 Series Routers 1 ASR 1000 Series Routers Software Overview 1 Consolidated Packages 2 Important Information About Consolidated Packages 2 Individual Software SubPackages Within a Consolidated Package 3 Important Notes About Individual SubPackages 3 Optional Software SubPackages Outside of Consolidated Packages 4 Important Notes About Optional SubPackages 4 Provisioning Files 4 Important Notes About Provisioning Files 5 ROMmon Image 5 File to Upgrade Field Programmable Hardware Devices 5 Processes Overview 6 IOS as a Process 7 Dual IOS Processes 8 File Systems on the Cisco ASR 1000 Series Router 8 Autogenerated File Directories and Files 9 Important Notes About Autogenerated Directories Using Cisco IOS XE Software
1
Accessing the CLI Using a Router Console 1 Accessing the CLI Using a Directly-Connected Console 2 Connecting to the Console Port 2 Using the Console Interface 2 Accessing the CLI from a Remote Console Using Telnet 3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
iii
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Preparing to Connect to the Router Console Using Telnet 3 Using Telnet to Access a Console Interface 3 Accessing the CLI from a Remote Console Using a Modem 4 Using the Auxiliary Port Using Keyboard Shortcuts
4 5 5
Using the History Buffer to Recall Commands Understanding the Command Mode Understanding the Diagnostic Mode Getting Help 8 Finding Command Options Saving Configuration Changes Managing Configuration Files Powering Off a Router
14 8 6 7
11
13
Finding Support Information for Platforms and Cisco Software Images Using the Cisco Feature Navigator 14 Using the Software Advisor 15 Using the Software Release Notes 15 Console Port, Telnet, and SSH Handling Console Port Handling Overview
1 2 1 1
14
Console Port Overview for the Cisco ASR 1000 Series Routers Telnet and SSH Overview for the Cisco ASR 1000 Series Routers Persistent Telnet and Persistent SSH Overview Configuring a Console Port Transport Map Examples 4 Configuring Persistent Telnet Prerequisites 5 Examples 7 Configuring Persistent SSH Examples 10
8 5 3 2
Viewing Console Port, SSH, and Telnet Handling Configurations Important Notes and Restrictions
16 1 1
11
Consolidated Packages and SubPackages Management Running the Cisco ASR 1000 Series Routers: An Overview
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iv
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Running the Cisco ASR 1000 Series Routers Using Individual and Optional SubPackages: An Overview 2 Running the Cisco ASR 1000 Series Routers Using a Consolidated Package: An Overview 2 Running the Cisco ASR 1000 Series Routers: A Summary 3 Software File Management Using Command Sets The request platform Command Set 4 The copy Command 5 The issu Command Set 5
4
Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages 6 Quick Start Software Upgrade 6 Managing and Configuring a Router to Run Using a Consolidated Package 7 Managing and Configuring a Consolidated Package Using the copy Command 7 Managing and Configuring a Consolidated Package Using the request platform software package install Command 8 Managing and Configuring a Router to Run Using Individual SubPackages From a Consolidated Package 10 Extracting a Consolidated Package and Booting Using the Provisioning File 10 Copying a Set of Individual SubPackage Files, and Booting Using a Provisioning File 14 Managing and Configuring a Router to Run Using Optional SubPackages 14 Installing an Optional SubPackage 15 Uninstalling an Optional SubPackage 16 Troubleshooting Software Mismatch with ESP Board ASR1000-ESP10-N 18 Upgrading Individual SubPackages Upgrading a SPA SubPackage
18 19
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers 1 Contents
2 2
ISSU Upgrade for Redundant Platforms 2 Overview of ISSU on the Cisco ASR 1000 Series Routers 3 ISSU Rollback Timer Overview 4 Software Upgrade with Dual IOS Processes on a Single RP Overview 4 Cisco IOS XE Software Package Compatibility for ISSU 5 Restrictions for ISSU 5 ISSU Upgrade Procedures 6 Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration 6 Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration 12 In Service One-Shot Software Upgrade Procedure 73
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) 74 Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2) 74 Using ISSU to Upgrade SubPackages (Prior to Cisco IOS XE Release 2.1.2) 74 Upgrade Process With Service Impact for Nonredundant Platforms 76 Configuring SSO on a Cisco ASR 1001, Cisco ASR 1002, or Cisco ASR 1004 Router 76 Using SubPackages for Software Upgrade on a Cisco ASR 1001 Router 78 Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (software upgrade Command Set) 93 Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (request platform Command Set) 118 Minimal Disruptive Restart ISSU 139 Restrictions and Limitations 140 High Availability Considerations 141 Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR 141 Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR 151 Using ISSU to Upgrade the SubPackages on a Cisco ASR 1006 or ASR 1013 Router (issu Command Set) with MDR 151 Using ISSU to Upgrade SubPackages on a Cisco ASR 1006 Router or ASR 1013 Router (request platform command set) with MDR 185 Additional References 222 Related Documents 222 Standards 222 MIBs 222 RFCs 222 Technical Assistance 223 Feature Information for Software Upgrade Process High Availability Overview Contents
1 2 1 1 224
Hardware Redundancy Overview on the Cisco ASR 1000 Series Routers Software Redundancy on the Cisco ASR 1000 Series Routers 4 Software Redundancy Overview 4 Second IOS Process on a Cisco ASR 1002 or 1004 Router 5 Configuring two Cisco IOS process on one RP 5 Route Processor Redundancy
6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
vi
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
IPsec Failover
8 8
Bidirectional Forwarding Detection Additional References 9 Related Documents 9 Standards 9 MIBs 9 RFCs 9 Technical Assistance 9
Feature Information for High Availability Overview Broadband Scalability and Performance Finding Feature Information in This Module Contents
1 1 1
10
PPP Sessions and L2TP Tunnel Scaling 2 Restrictions for PPP Sessions and L2TP Tunnel Scaling ISG Scaling
3 4
Configuring the Cisco ASR 1000 Series Router for High Scalability 4 Configuring Call Admission Control 5 Control Plane Policing 5 VPDN Group Session Limiting 6 PPPoE Session Limiting 6 Monitoring PPP Sessions Using the SNMP Management Tools 6 Configuring the Access Interface Input and Output Hold Queue 6 Configuring the keepalive Command 6 Scaling the L2TP Tunnel Configurations 7 Using the cisco-avpair="lcp:interface-config" RADIUS Attribute 7 Enhancing the Scalability of Per-User Configurations 8 Setting the VRF and IP Unnumbered Interface Configurations in User Profiles 8 Setting the VRF and IP Unnumbered Interface Configurations in Virtual Interface Templates Redefining User Profiles to Use the ip:vrf-id and ip:ip-unnumbered VSAs 8 Walk-by User Support for PWLAN in ISG 9 Restrictions for Walk-by Session Support for PWLAN in ISG ISG Scaling to Support Lite Sessions 9 Additional References 11 Related Documents 11 Standards 11 MIBs 11 RFCs 11
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
vii
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Technical Assistance
11 12
Feature Information for Broadband Scalability and Performance Configuring Cisco License Call Home Contents
1 2 2 2 1 1
Finding Feature Information in This Module Prerequisites for Cisco License Call Home Restrictions for Cisco License Call Home
Informatio n About Cisco License Call Homes Cisco License Call Home Interface 2
How to Configure Cisco License Call Home 3 Installing Licenses or Upgrading Software by Using Cisco License Call Home Rehosting a License by Using Cisco License Call Home 4 Requesting a License Resend by Using Cisco License Call Home 5
Configuration Examples for Cisco License Call Home 6 Example: Installing Licenses or Upgrading Software by Using Cisco License Call Home Example: Rehosting a License by Using Cisco License Call Home 7 Example: Requesting a License Resend by Using Cisco License Call Home 8 Additional References 9 Related Documents 9 Standards 9 MIBs 9 RFCs 9 Technical Assistance 9 Feature Information for Cisco License Call Home Configuring Call Home Contents
1 1 10
Information About Call Home 2 Benefits of Using Call Home 2 How to Obtain Smart Call Home Service Prerequisites for Call Home
3
How to Configure Call Home 4 Configuring the Management Interface VRF 4 What To Do Next 5 Configuring a Destination Profile 5 Configuring a Destination Profile to Send Email Messages Configuring a Destination Profile to Send HTTP Messages Working With Destination Profiles 14
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
6 10
viii
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Subscribing to Alert Groups 17 Periodic Notification 18 Message Severity Threshold 18 Syslog Pattern Matching 19 Configuring Contact Information 21 Example 22 Configuring the Number of Call Home Messages Sent Per Minute 23 Enabling and Disabling Call Home 23 Sending Call Home Communications Manually 24 Sending a Call Home Test Message Manually 24 Sending Call Home Alert Group Messages Manually 24 Submitting Call Home Analysis and Report Requests 25 Sending the Output of a Command to Cisco or an E-Mail Address 27 How To Configure Call Home to Support the Smart Call Home Service Prerequisites 28 Configure and Enable Call Home 28 Declare and Authenticate a CA Trustpoint 31 Examples 33 Start Smart Call Home Registration 33 What To Do Next 34 Displaying Call Home Configuration Information Examples 35 Default Settings
39 40 34 27
Message Contents 42 Sample Syslog Alert Notification in Long Text Format Sample Syslog Alert Notification in XML Format 50 Additional References 57 Related Documents 58 Standards 58 MIBs 58 RFCs 58 Technical Assistance 59 Feature Information for Call Home
59 1
46
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
ix
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Restrictions for Cisco RTU License
2
Information About Cisco RTU License 2 Overview of the Cisco Licensing Mechanism RTU Supported Software Licenses 2 Evaluation Licenses and RTU Licenses 3 How to Activate an Evaluation License 4
Configuration Examples for RTU Supported Software Licenses 6 Configuring Throughput 6 Example: Accepting the Global EULA 6 Example: Accepting an EULA for Software Redundancy License 7 Example: Accepting an EULA for the Inter-Chassis Redundancy License Example: Accepting an EULA for the Lawful Intercept License 8 Example: Sample Output for show Commands 9 Sample Output for the show license EULA Command 9 Sample Output for the show license all Command 10 Additional References 11 Related Documents 11 MIBs 12 Technical Assistance 12 Feature Information for Cisco RTU License
13
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Finding Feature Information Contents
2 2 3 4 4 1
Overview of the iWAG Deployment Restrictions for the GTP of the iWAG
Information About IP Address Assignment Information About Authentication Methods Information About GGSN Selection
5
How to Configure Authentication, Authorization, and Accounting for the iWAG How to Configure DHCP when the iWAG Acts as a DHCP Proxy How to Configure a Subscriber Initiator for the iWAG How to Configure a Tunnel Initiator for the iWAG How to Configure the GTP of the iWAG
19 15 17 13 8 10
How to Configure the Cisco ISG Class Map and Policy Map for the iWAG
Configuration Examples for the iWAG 21 Example: Configuring the iWAG Using the TAL Authentication Method
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Example: Configuring the iWAG Using the EAP-SIM Authentication Method 23 Example: Configuring the iWAG Using the Web Logon Authentication Method 25 Multiple-Flow Tunnel
27 27
GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers Restrictions for GTPv2 of the iWAG 28 GTPv2 Configuration 28 RADIUS Configuration 29 Intra-iWAG Roaming 29 iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers Enabling SSO Support for the GTP 31 ISG Policy Templating on the Cisco ASR 1000 Series Aggregation Services Routers Restrictions for ISG Policy Templating 32 Configuring ISG Policy Templating 32 Additional References 33 Related Documents 33 Standards 33 MIBs 33 RFCs 33 Technical Assistance 34
32
30
Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload 34 UniDirectional Link Detection (UDLD) Protocol Finding Feature Information Contents
1 2 1 1
Information About the UDLD Protocol 2 UDLD Overview 2 Configuring the UDLD Aggressive Mode Default UDLD Configuration 3
How to Configure the UDLD Protocol 4 Enabling UDLD Globally 4 Enabling UDLD on Individual LAN Interfaces 4 Disabling UDLD on Fiber-Optic LAN Interfaces 6 Configuring the UDLD Probe Message Interval 7 Resetting the Disabled LAN Interfaces Manually 8 Resetting the Disabled LAN Interfaces Automatically Debugging UDLD 9 Configuration Examples for UDLD Protocol
10
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xi
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Example: Verifying a UDLD Configuration 10 Example: Verifying Information About Neighbors 10 Example: Displaying all the UDLD Interface Statuses 11 Additional References 12 Related Documents 12 Standards 12 MIBs 12 RFCs 12 Technical Assistance 13 Feature Information for Configuring UDLD on Cisco ASR 1000 Series Aggregation Services Routers Using the Management Ethernet Interface Finding Feature Information in This Module Contents
1 2 1 1 14
IP Address Handling in ROMmon and the Management Ethernet Port Gigabit Ethernet Management Interface VRF
3
Common Ethernet Management Tasks 3 Viewing the VRF Configuration 4 Viewing Detailed VRF Information for the Management Ethernet VRF 4 Setting a Default Route in the Management Ethernet Interface VRF 4 Setting the Management Ethernet IP Address 5 Telnetting over the Management Ethernet Interface 5 Pinging over the Management Ethernet Interface 5 Copy Using TFTP or FTP 5 NTP Server 6 SYSLOG Server 6 SNMP-Related Services 6 Domain Name Assignment 6 DNS service 6 RADIUS or TACACS+ Server 6 VTY lines with ACL 7 Additional References 8 Standards 8 MIBs 8 RFCs 8 Technical Assistance 8 Feature Information for Using the Management Ethernet Interface
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xii
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Network Synchronization Support Finding Feature Information Contents
1 2 1 1
Synchronization Status Message and Ethernet Synchronization Messaging Channel Synchronization Status Message 5 Ethernet Synchronization Messaging Channel 5 Clock Selection Algorithm 6 Restrictions for Network Synchronization
6
Configuring Network Synchronization 7 Configuring Clock Recovery from SyncE 7 Configuring Clock Recovery from a BITS Port 9 Configuring Clock Recovery with a BITS Port as an Input-Source 9 Configuring Clock Recovery with a BITS Port as an Output-Source 11 Configuring SyncE by Using the Line to External Feature 13 Managing Synchronization 15 Verifying the Network Synchronization Configuration 17 Troubleshooting the Network Synchronization Configuration 20 Additional References 22 Related Documents 22 Standards 22 MIBs 22 RFCs 22 Technical Assistance 22 Feature Information for Network Synchronization Support
23 1
Service Provider WiFi: Support for Integrated Ethernet Over GRE Finding Feature Information Contents
2 3 3 2
Restrictions for Configuring Ethernet Over GRE Prerequisites for Configuring Ethernet Over GRE
Information About Configuring Ethernet Over GRE 3 EoGRE Deployment with PMIPv6 Integrated for Mobility Service 6 EoGRE Deployment with GTP Integrated for Mobility Service 7 EoGRE Deployment with ISG Integrated for Simple IP Service 7 Supported Features
8 8
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xiii
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Examples
11
Additional References 13 Related Documents 13 Standards 13 MIBs 13 RFCs 13 Technical Assistance 14 Feature Information for Configuring Ethernet Over GRE Configuring Bridge Domain Interfaces Finding Feature Information Contents
1 1 1 1 14
Information About Bridge Domain Interfaces 2 Ethernet Virtual Circuit Overview 2 Bridge Domain Interface Encapsulation 3 Assigning a MAC Address 3 Support for IP Protocols 3 Support for IP Forwarding 4 Packet Forwarding 4 Layer 2 to Layer 3 4 Layer 3 to Layer 2 4 Link States of a Bridge Domain and a Bridge Domain Interface BDI Initial State 5 BDI Link State 5 Bridge Domain Interface Statistics 5 Creating or Deleting a Bridge Domain Interface Bridge Domain Interface Scalability
6 6 6
How to Configure a Bridge Domain Interface Example 8 Additional References 10 Related Documents 10 Standards 10 MIBs 10 RFCs 10 Technical Assistance 10
11
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xiv
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Enabling Support for Tunable DWDM-XFP-C Configuring the DWDM-XFP-C Module 4 Verifying the ITU Configuration 4 Monitoring and Maintaining Multilink Frame Relay Finding Feature Information in This Module Contents
1 2 2 2 1 1 1
Feature Overview
Configuring Multilink Frame Relay Additional References 3 Related Documents 3 Standards 3 MIBs 3 RFCs 3 Technical Assistance 3
Feature Information for Monitoring and Maintaining Multilink Frame Relay Configuring MPLS Layer 2 VPNs Finding Feature Information Contents
1 1 1
Overview of L2VPN Interworking 2 L2VPN Interworking Modes 2 Ethernet or Bridged Interworking IP or Routed Interworking 3
Virtual Private LAN Services 4 Reverse Layer 2 Gateway Protocol 4 BPDUs Sent Out of R-L2GP Ports 5 BPDUs Received on R-L2GP Ports 6 BPDUs Received on L2 Protocol Forwarding PW 6 Restrictions for R-L2GP 6 Configuring the R-L2GP 6 Configuring the MST 7 Configuring an R-L2GP Instance 8 Attaching an R-L2GP Instance to a Port 9 Example: Configuring an R-L2GP 10 Configuring the Layer 2 Protocol Forwarding Virtual Private LAN Services Pseudowire between Two Redundant NPES 10 Verifying an R-L2GP Configuration 11
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xv
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Prerequisites for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
12 12
Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking 14 Example: Frame Relay-to-ATM Bridged Interworking on an ATM-PE Router 18 Example: Frame Relay-to-ATM Bridged Interworking on a Frame Relay-PE Router Gigabit EtherChannel for Virtual Private Wire Service 25 Supported Modes 25 GEC Like-to-Like Mode 25 Any-to-GEC Mode 26 Restrictions for Gigabit EtherChannel for Virtual Private Wire Service Configuring Gigabit EtherChannel for Virtual Private Wire Service 27 EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking 27 EtherChannel-to-EtherChannel over MPLS (Routed) Interworking 29 Example: GEC Like-to-Like (Routed) Interworking 31 Any-to-EtherChannel over MPLS (Bridged) Interworking 32 Any-to-EtherChannel over MPLS (Routed) Interworking 34 Additional References 38 Related Documents 38 Standards 38 MIBs 38 RFCs 39 Technical Assistance 39 Feature Information for Configuring MPLS Layer 2 VPNs Glossary
42 39
24
26
LSM-MLDP-based MVPN Support 1 Restrictions and Usage Guidelines 1 Configuring LSM-MLDP-based MVPN Support 2 Configuring MLDP MVPN Intranet Services 2 Verification 6 Configuring MLDP MVPN for Extranet Services Configuring MLDP TE-FRR Support 19 Configuring MLDP with PIM-based MVPN 20 MLDP Support with Load Balancing 20 Root Node Redundancy 20 Verification 20 Sample Configuration for MLDP MVPN 31 Configuration Example Using SSM Mode 31 Configuration Example Using SM Mode 47
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xvi
OL-16506-14
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
Troubleshooting LSM MLDP based MVPN Support Tracing and Trace Management 1 Tracing Overview 1 How Tracing Works 1 Tracing Levels 2 Viewing a Tracing Level 3 Setting a Tracing Level 4 Viewing the Content of the Trace Buffer
63
5 1
Web User Interface Overview 1 Web User Interface General Overview 1 Legacy Web User Interface Overview 2 Graphics-Based Web User Interface Overview 3 Persistent Web User Interface Transport Maps Overview Configuring the Router for Web User Interface Access Authentication and the Web User Interface Clocks and the Web User Interface Accessing the Web User Interface Using Auto Refresh
9 10 7 8 7 7 5
APPENDIX
APPENDIX
1 1
Configuring the Router to Boot the Consolidated Package on the TFTP Server Copying the Consolidated Package from the TFTP Server to the Router
5
Configuring the Router to Boot Using the Consolidated Package Stored on the Router Extracting the SubPackages from a Consolidated Package into the Same File System Extracting the SubPackages from a Consolidated Package into a Different File System Configuring the Router to Boot Using the SubPackages
10
6 7 9
Backing Up Configuration Files 14 Copying a Startup Configuration File to Bootflash 14 Copying a Startup Configuration File to an USB Flash Disk 14 Copying a Startup Configuration File to a TFTP Server 15 Enabling a Second IOS Process on a Single RP Using SSO
15
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xvii
Contents
7 / 14 / 10 D r a ft - - C I S C O CO N F I D E N T I A L
ISSUConsolidated Package Upgrade
19
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xviii
OL-16506-14
Preface
Revised: July 30, 2013, OL-16506-14
This preface describes the objectives and organization of this document and explains how to find additional information on related products and services. This preface contains the following sections:
Objectives, page xix Document Revision History, page xx Organization, page xxii Related Documentation, page xxiv Conventions, page xxv Obtaining Documentation and Submitting a Service Request, page xxvi
Objectives
This document provides an overview of software functionality that is specific to the Cisco ASR 1000 Series Aggregation Services Routers. It is not intended as a comprehensive guide to all of the software features that can be run using the Cisco ASR 1000 Series Routers, but only the software aspects that are specific to these routers. For information on general software features that are also available on the Cisco ASR 1000 Series Routers, see the Cisco IOS XE technology guide for that specific software feature.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xix
Preface
Added information for the following features in the iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload chapter:
GTP Version 2 in the iWAG on the Cisco ASR 1000
IOS XE 3.9.0
Added Multiple Flows Tunnel section in the iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload chapter. Added new content to document UniDirectional Link Detection (UDLD) Protocol in the UniDirectional Link Detection (UDLD) Protocol chapter. Added new content to document Configuring Ethernet Over Soft GRE in the Service Provider WiFi: Support for Integrated Ethernet Over GRE chapter. Added new content to document iWAG on the Cisco ASR 1000 Series Aggregation Services Routers for Service Provider WiFi Offload in the iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload chapter. Added Minimal Disruptive Restart Process section in the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Added new content to document the Configuring Cisco Right-To-Use License in the Configuring a Cisco Right-To-Use License chapter. Added new content to the Synchronous Ethernet in the Network Synchronization Support chapter. Added new content to document the Walk-by User Support for PWLAN in ISG in the Broadband Scalability and Performance chapter. Added new content to the bridge domain interface configurations in the Configuring Bridge Domain Interfaces chapter.
IOS XE 3.8.0
IOS XE 3.7.0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xx
OL-16506-14
Preface
IOS XE 3.6.0
Added new content to document the Cisco License Call Home in the Configuring Cisco License Call Home chapter. Added new content to document the Frame Relay to ATM Bridged Interworking in the Configuring MPLS Layer 2 VPNs chapter. Added new content to document the xconnect support on GEC (VPWS) on ASR1000 in the Configuring MPLS Layer 2 VPNs chapter. Added new content to document the Monitoring and Maintaining Multilink Frame Relay feature in the Monitoring and Maintaining Multilink Frame Relay chapter. Added new content to document In Service One-Shot Software Upgrade Procedure in the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Added new content to document the Scalability and Performance in the Broadband Scalability and Performance chapter. Added software upgrade information for ASR 1001 chassis in the Using SubPackages for Software Upgrade on a Cisco ASR 1001 Router section in Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Added new content to document bridge domain interface configurations in the Configuring Bridge Domain Interfaces chapter. Added new content to document the Synchronous Ethernet in the Network Synchronization Support chapter. Added upgrade and file package information in the Software Packaging and Architecture chapter. Added restriction regarding ISSU support in Cisco IOS XE Release 3.1S in Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Added support for the Call Home feature in the Configuring Call Home chapter. Moved the ISSU compatibility tables into the Release Notes for Cisco ASR 1000 Series Aggregation Services Routers document. Relocated other ISSU compatibility information into the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter.
IOS XE 2.6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xxi
Preface
IOS XE 2.5
Updated the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter with new compatibility information.
IOS XE 2.4
Updated the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter with new compatibility information. Updated book with installation information for the new optional subpackage for the Cisco WebEx Node for ASR 1000 Series.
IOS XE 2.3
Updated the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter with new compatibility information. Updated the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter with new compatibility information. Added new content to document compatibility of different versions of Cisco IOS XE software in the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Updated book to document ISSU procedures for Cisco IOS XE Release 2.2. Removed ISSU procedures from the Consolidated Packages and SubPackage Management chapter of the book and created the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers chapter. Added the Troubleshooting Software Mismatch with ESP Board ASR1000-ESP10-N section for the Cisco ASR 1000 Embedded Services Processor 10G Non Crypto Capable feature. Added the Configuring and Accessing the Web User Interface section. Added Appendix Configuration Examples. First release of the book.
IOS XE 2.2
IOS XE 2.2
November 3, 2008
IOS XE 2.2
October 3, 2008
IOS XE 2.2
IOS XE 2.1
July 2, 2008
IOS XE 2.1
May 2, 2008
Organization
This document contains the following chapters: Title Software Packaging and Architecture Description Provides an introduction to Cisco ASR 1000 Series Routers software packaging, processes, and file systems. Provides an introduction to accessing the command-line interface (CLI) and using the Cisco software and related tools.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xxii
OL-16506-14
Preface
Description Provides an overview and configuration options for the handling of incoming console port, telnet, and SSH traffic on the Cisco ASR 1000 Series Routers. Provides information on downloading, installing, and running the software on the Cisco ASR 1000 Series Routers. Provides information on ISSU compatibility and performing limited-downtime software upgrades on the Cisco ASR 1000 Series Routers. Provides an overview of the High Availability architecture, behavior, and features on the Cisco ASR 1000 Series Routers. Provides information on scaling and performance on the Cisco ASR 1000 Series Routers. Provides information on activating the Cisco License for Call Home feature. Provides information about the Call Home feature, which supports e-mail-based and web-based notification of critical system events. A versatile range of message formats are available for optimal compatibility with pager services, standard e-mail, or XML-based automated parsing applications. Provides information on activating the Cisco Right-To-Use License. Provides information on the deployment of the Intelligent Wireless Access Gateway (iWAG) feature on the Cisco ASR 1000 Series Aggregation Services Routers that involves two main technologies: the General Packet Radio Service (GPRS) Tunneling Protocol (GTP) for connecting to the Cisco Gateway GPRS Support Node (Cisco GGSN) and the Mobile Access Gateway (MAG) using Proxy Mobile IPv6 (PMIPv6) for connecting to the Cisco Packet Data Network Gateway (PGW). Provides an overview and configuration options for the UDLD protocol on the Cisco ASR 1000 Series Routers. Provides an overview and configuration options for the Management Ethernet interface on the Cisco ASR 1000 Series Routers.
Scalability and Performance Cisco License Call Home Configuring Call Home for Cisco ASR 1000 Series Aggregation Services Routers
Configuring Cisco Right-To-Use License iWAG on ASR 1000 Series Aggregation Services Routers for Service Provider WiFi Offload
UniDirectional Link Detection (UDLD) Protocol Using the Management Ethernet Interface
Synchronous Ethernet Support On The Cisco Provides an overview and configuration options for the ASR 1000 Series Routers Synchronous Ethernet on the Cisco ASR 1000 Series Routers. Configuring Ethernet Over Soft GRE Provides an overview and configuration for the Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an IP internetwork.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xxiii
Preface
Description Provides an overview of configuration options for the Bridge Domain Interface on the Cisco ASR 1000 Series Routers.
Monitoring and Maintaining Multilink Frame Provides an overview of monitoring and maintaining Relay the Multilink Frame Relay feature for the Cisco ASR 1000 Series Routers. Configuring MPLS Layer 2 VPNs LSM-MLDP-based MVPN Support Provides an overview of The Frame Relay to ATM Bridged Interworking feature Provides information on the Label Switched Multicast (LSM) feature supports IPv4 and IPv6 multicast traffic over a Multi-Protocol Label Switching (MPLS) network. Provides an overview of tracing on the Cisco ASR 1000 Series Router, and how to manage the tracing process and files. Provides an overview of the Cisco ASR 1000 Series Router web user interface, and information on configuring and accessing the web user interface.
Related Documentation
This section refers you to other documentation that also might be useful as you configure your Cisco ASR 1000 Series Router. The documentation listed below is available online.
Cisco IOS XE Software Command References Command Lookup Tool (cisco.com login required)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xxiv
OL-16506-14
Preface
Conventions
This document uses the following conventions: Convention bold font italic font [ ] {x | y | z } [x|y|z] string
courier
Indication Commands and keywords and user-entered text appear in bold font. Document titles, new or emphasized terms, and arguments for which you supply values are in italic font. Elements in square brackets are optional. Required alternative keywords are grouped in braces and separated by vertical bars. Optional alternative keywords are grouped in brackets and separated by vertical bars. A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.
font
Terminal sessions and information the system displays appear in courier font. Nonprinting characters such as passwords are in angle brackets. Default responses to system prompts are in square brackets. An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line.
< > [ ] !, #
Note
Tip
Caution
Means reader be careful. In this situation, you might perform an action that could result in equipment damage or loss of data.
Timesaver
Means the described action saves time. You can save time by performing the action described in the paragraph.
Warning
Means reader be warned. In this situation, you might perform an action that could result in bodily injury.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-14
xxv
Preface
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
xxvi
OL-16506-14
Software Packaging on the Cisco ASR 1000 Series Routers, page 1 Processes Overview, page 6 File Systems on the Cisco ASR 1000 Series Router, page 8 Autogenerated File Directories and Files, page 9
ASR 1000 Series Routers Software Overview, page 1 Consolidated Packages, page 2 Individual Software SubPackages Within a Consolidated Package, page 3 Optional Software SubPackages Outside of Consolidated Packages, page 4 Provisioning Files, page 4 ROMmon Image, page 5 File to Upgrade Field Programmable Hardware Devices, page 5
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Software Packaging and Architecture Software Packaging on the Cisco ASR 1000 Series Routers
Importantly, IOS (the RPIOS subpackage) is considered one of the seven individual subpackages that makes up a complete consolidated package. For additional information on individual software subpackages, see the Consolidated Packages section on page 2. A collection of software subpackages packaged together creates a single consolidated package. A consolidated package allows users to upgrade all individual subpackages on the router with a single software image download. Consolidated packages can be downloaded from Cisco.com; users who want to run the router using individual subpackages that are part of the consolidated package must first download the image from Cisco.com and extract the individual subpackages from the image, which can be done by entering request platform command-line interface commands. Beginning in Cisco IOS XE Release 2.4, support for a supplemental, optional subpackage of type called sipspawma is introduced to support the Cisco WebEx Node for ASR 1000 Series shared port adapter (SPA). Optional subpackages are installed similarly to individual subpackages; however, optional subpackages are not bundled as part of a consolidated package like prior support for the individual subpackages, and optional subpackages must be downloaded independently. See the Consolidated Packages section on page 2 and Individual Software SubPackages Within a Consolidated Package section on page 3 of this book for additional information on extracting individual subpackages from a consolidated package, supplemental optional subpackages, and other information on managing software.
Consolidated Packages
A consolidated package is a single image composed of individual software subpackage files. A single consolidated package file is a bootable file, and the Cisco ASR 1000 Series Router can be run using the consolidated package.
Note
Consolidated packages only contain the required individual subpackage files. These packages do not contain supplemental, optional subpackages, such as the sipspawma package for the Cisco WebEx Node for ASR 1000 Series. Each consolidated package also contains a provisioning file. A provisioning file is used for booting in cases where the individual subpackages are extracted from the consolidated package, or optional subpackages are used to run the router. For additional information on the advantages and disadvantages of running a complete consolidated package, see the Running the Cisco ASR 1000 Series Routers: An Overview section on page 1. For additional information on provisioning files, see the Provisioning Files section on page 4. For information about the consolidated packages available in a specific version of Cisco IOS XE, see the release notes for that version of Cisco IOS XE. The Cisco IOS XE Software Release Notes contains the release notes for each version of Cisco IOS XE.
For each version of a consolidated package, the RPBase, RPControl, ESPBase, SIPSPA, and SIPBase subpackages are identical among consolidated packages. For each version of consolidated package, the RPIOS subpackage is always different among consolidated packages.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Packaging and Architecture Software Packaging on the Cisco ASR 1000 Series Routers
A consolidated package file is a bootable file. If the router is configured to run using a the complete consolidated package, boot the router using the consolidated package file. If the router is configured to run using individual subpackages, boot the router using the provisioning file. For additional information on the advantages and disadvantages of running a complete consolidated package, see the Running the Cisco ASR 1000 Series Routers: An Overview section on page 1. For additional information on provisioning files, see the Provisioning Files section on page 4. If you need to install optional subpackages, then you must boot the router using the individual subpackage provisioning file method.
Purpose Provides the operating system software for the Route Processor. Controls the control plane processes that interface between the IOS process and the rest of the platform. Exports processing of restricted components, such as Secure Socket Layer (SSL), Secure Shell (SSH), and other security features. Provides the Cisco IOS kernel, which is where IOS features are stored and run. Each consolidated package has a different RPIOS. Provides the ESP operating system and control processes, and the ESP software. Controls the SIP operating system and control processes. Provides the SPA driver and Field Programmable Device (FPD) images.
Individual subpackages cannot be downloaded from Cisco.com individually. To get these individual subpackages, users must download a consolidated package and then extract the individual subpackages from the consolidated package using the command-line interface. If the router is being run using individual subpackages instead of being run using a complete consolidated package, the router must be booted using a provisioning file. A provisioning file is included in all consolidated packages and is extracted from the image along with the individual subpackages whenever individual subpackages are extracted. For additional information on provisioning files, see the Provisioning Files section on page 4.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Packaging and Architecture Software Packaging on the Cisco ASR 1000 Series Routers
Optional subpackages are downloaded separately from consolidated package files. Optional subpackages are not contained within a consolidated package for a release. Optional package installation works similarly to the installation of individual subpackages using a provisioning file. Optional subpackages can be uninstalled to remove provisioning when the package no longer applies to an RP. Optional subpackages are easily supported by the standard ISSU upgrade process as long as the package is located in the directory of the provisioning file for each RP.
Provisioning Files
Note
You must use the provisioning files to manage the boot process if you need to install optional subpackages. Provisioning files manage the boot process when the Cisco ASR 1000 Series Router is configured to run using individual subpackages or optional subpackages (such as the package for the Cisco WebEx Node for ASR 1000 Series). When individual subpackages are being used to run the Cisco ASR 1000 Series Router, the router has to be configured to boot the provisioning file. The provisioning file manages the bootup of each individual subpackage and the Cisco ASR 1000 Series Router assumes normal operation. Provisioning files are extracted automatically when individual subpackage files are extracted from a consolidated package. Provisioning files are not necessary for running the router using the complete consolidated package; if you want to run the router using the complete consolidated package, simply boot the router using the consolidated package file. See the Running the Cisco ASR 1000 Series Routers: An Overview section on page 1 for additional information on the advantages and disadvantages of running individual subpackages versus running a complete consolidated package.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Packaging and Architecture Software Packaging on the Cisco ASR 1000 Series Routers
Each consolidated package contains two provisioning files. One of the provisioning files is always named packages.conf, while the other provisioning file will have a name based on the consolidated package naming structure. In any consolidated package, both provisioning files perform the exact same function. In most cases, the packages.conf provisioning file should be used to boot the router. Configuring the router to boot using this file is generally easier because the router can be configured to boot using packages.conf, so no changes have to be made to the boot statement when Cisco IOS XE is upgraded (the boot system file-system:packages.conf configuration command can remain unmodified before and after an upgrade). The provisioning file and individual subpackage files must be kept in the same directory. The provisioning file does not work properly if the individual subpackage files are in other directories. The provisioning filename can be renamed; the individual subpackage filenames cannot be renamed. After placing the provisioning file and the individual subpackage files in a directory and booting the router, it is highly advisable not to rename, delete, or alter any of these files. Renaming, deleting, or altering the files can lead to unpredictable router problems and behaviors.
ROMmon Image
An independent ROMmon image is released periodically separate from consolidated packages or any other software releases. See the documentation that accompanies the ROMmon image for information on each ROMmon image. For additional information on ROMmon, see the Cisco ASR 1000 Series Routers Maintain and Operate Guide.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Processes Overview
Cisco IOS XE has numerous components that run entirely as separate processes on the Cisco ASR 1000 Series Routers. This modular architecture increases network resiliency by distributing operating responsibility among separate processes rather than relying on Cisco IOS software for all operations. This section covers the following topics:
Table 2 provides a list of the important individual processes for the Cisco ASR 1000 Series Routers. These processes run in the background, and the CLI on Cisco ASR 1000 Series Routers using Cisco IOS-XE is identical in look, feel, and usage to the Cisco IOS CLI on most platforms. This information is provided because it may be useful for checking router state and troubleshooting, but understanding this information is not essential to understanding most router operations.
Table 2 Individual Processes
Purpose Responsible for all chassis management functions, including management of the HA state, environmental monitoring, and FRU state control. Provides an interface between the IOS process and many of the information-gathering functions of the underlying platform kernel and operating system. Provides IOS facing logging services to processes running on each FRU.
Affected FRUs RP (one instance per RP) SIP (one instance per SIP) ESP (one instance per ESP) RP (one instance per RP) SIP (one instance per SIP) ESP (one instance per ESP) RP (one instance per RP) SIP (one instance per SIP) ESP (one instance per ESP) RP (one instance per RP) SIP (one instance per SIP)
SubPackage Mapping RPControl SIPBase ESPBase RPControl SIPBase ESPBase RPControl SIPBase ESPBase RPControl SIPBase
Host Manager
Logger
Interface Manager
Provides an interface between the IOS process and the per-SPA interface processes on the SIP. The IOS process implements all forwarding and routing features for the router.
IOS
RP (one per software RPIOS redundancy instance per RP). Maximum of two instances per RP.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 2
Purpose Manages the downloading of configuration to each of the ESPs and the communication of forwarding plane information, such as statistics, to the IOS process. The integration point between platform policy application, such as authentication and the IOS process.
Affected FRUs
SubPackage Mapping
RP (one per software RPControl redundancy instance per RP). Maximum of two instances per RP. ESPBase ESP (one per ESP) RP (one per software RPControl redundancy instance per RP). Maximum of two instances per RP. RPControl
Pluggable Services
Shell Manager
Provides all user interface RP (one instance per features and handling related RP) to features in the nonIOS image of the consolidated package, which are also the features available in diagnostic mode when the IOS process fails. Provides an isolated process driver for a specific SPA. SPA (one instance per SPA per SIP)
SPA driver process CPP driver process CPP HA process CPP SP process
Manages the CPP hardware ESP (one instance per forwarding engine on the ESP. ESP) Manages HA state for the CPP ESP (one instance per hardware forwarding engine. ESP) Performs high-latency tasks for the CPP-facing functionality in the ESP instance of the Forwarding Manager process. ESP (one instance per ESP)
IOS as a Process
In almost all previous Cisco router platforms, an overwhelming majority of the internal software processes are run using Cisco IOS memory. The Cisco ASR 1000 Series Routers introduce a distributed software architecture that moves many operating system responsibilities out of the IOS process. In this architecture, IOS, which previously was responsible for almost all of the internal software processes, now runs as one of many Linux processes while allowing other Linux processes to share responsibility for running the router. This architecture allows for better allocation of memory so the router can run more efficiently. Furthermore, the Cisco ASR 1000 Series Routers has a command-line interface in diagnostic mode that can be accessed in certain scenarios even if the IOS process fails. See the Understanding the Diagnostic Mode section on page 7 for information on diagnostic mode.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Increased fault toleranceIn the event of an active IOS failure, the second IOS process immediately becomes the active IOS process with little to no service disruption. No downtime software upgradesIOS and other software on the router can be upgraded using the In Service Software Upgrade (ISSU) feature in the standby IOS process, thereby allowing the network to remain active during the software upgrade. See the Router# section on page 20 for additional information on when ISSU can and cannot be used to perform no downtime software upgrades.
File System bootflash: cns: harddisk: nvram: obfl: stby-bootflash: stby-harddisk: stby-usb[0-1]: system: tar: tmpsys: usb[0-1]:
Description The boot flash memory file system on the active RP. The Cisco Networking Services file directory. The hard disk file system on the active RP. The harddisk: file system is not available on the Cisco ASR 1002 Routers. Router NVRAM. You can copy the startup configuration to NVRAM or from NVRAM. The file system for Onboard Failure Logging files. The boot flash memory file system on the standby RP. The hard disk file system on the standby RP. The harddisk: file system is not available on the Cisco ASR 1002 Routers. The Universal Serial Bus (USB) flash drive file systems on the standby RP. The stby-usb: file system is not available on the Cisco ASR 1002 Routers. The system memory file system, which includes the running configuration. The archive file system. The temporary system files file system. The Universal Serial Bus (USB) flash drive file systems on the active RP. Only usb0: is available on the Cisco ASR 1002 Router.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
If you run into a file system not listed in Table 3, enter the? help option or see the copy command reference for additional information on that file system.
Description A crashinfo file may appear in the bootflash: or harddisk: file system. These files provide descriptive information of a crash and may be useful for tuning or troubleshooting purposes, but the files are not part of router operations and can be erased without impacting the functioning of the router.
core directory
The storage area for.core files. If this directory is erased, it will automatically regenerate itself at bootup. The .core files in this directory can be erased without impacting any router functionality, but the directory itself should not be erased.
lost+found directory This directory is created on bootup if a system check is performed. Its appearance is completely normal and does not indicate any issues with the router. tracelogs directory The storage area for trace files. Trace files are useful for troubleshooting; if the IOS process fails, for instance, users or troubleshooting personnel can access trace files using diagnostic mode to gather information related to the IOS failure. Trace files, however, are not part of router operations and can be erased without impacting the routers performance.
Any autogenerated file on the bootflash: directory should not be deleted, renamed, moved, or altered in any way unless directed by customer support. Altering autogenerating files on the bootflash: can have unpredictable consequences for system performance. Crashinfo, core, and trace files can be deleted, but the core and tracelog directories that are automatically part of the harddisk: file system should not be deleted.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Accessing the CLI Using a Router Console, page 1 Using the Auxiliary Port, page 4 Using Keyboard Shortcuts, page 5 Using the History Buffer to Recall Commands, page 5 Understanding the Command Mode, page 6 Understanding the Diagnostic Mode, page 7 Getting Help, page 8 Using the no and default Forms of Commands, page 11 Saving Configuration Changes, page 12 Managing Configuration Files, page 12 Filtering the Output of the show and more Commands, page 13 Powering Off a Router, page 14 Finding Support Information for Platforms and Cisco Software Images, page 14
Accessing the CLI Using a Directly-Connected Console, page 2 Accessing the CLI from a Remote Console Using Telnet, page 3 Accessing the CLI from a Remote Console Using a Modem, page 4
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Using Cisco IOS XE Software Accessing the CLI Using a Router Console
9600 bits per second (bps) 8 data bits No parity 1 stop bit No flow control
Step 2
Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or using the RJ-45-to-DB-9 DTE adapter (labeled Terminal).
After you attach the terminal hardware to the console port on the router and you configure your terminal emulation software with the proper settings, the following prompt appears:
Press RETURN to get started.
Step 2
Press Return to enter user EXEC mode. The following prompt appears:
Router>
Step 3
From user EXEC mode, enter the enable command as shown in the following example:
Router> enable
Step 4
At the password prompt, enter your system password. If an enable password has not been set on your system, this step may be skipped. The following example shows entry of the password enablepass:
Password: enablepass
Step 5
When your enable password is accepted, the privileged EXEC mode prompt appears:
Router#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Using Cisco IOS XE Software Accessing the CLI Using a Router Console
Step 6 Step 7
You now have access to the CLI in privileged EXEC mode and you can enter the necessary commands to complete your desired tasks. To exit the console session, enter the quit command as shown in the following example:
Router# quit
Note
To prevent disabling login on the line, be careful that you specify a password with the password command when you configure the login line configuration command. If you are using authentication, authorization, and accounting (AAA), you should configure the login authentication line configuration command. To prevent disabling login on the line for AAA authentication when you configure a list with the login authentication command, you must also configure that list using the aaa authentication login global configuration command. For more information about AAA services, see the Cisco IOS XE Security Configuration Guide, and the Cisco IOS Security Command Reference Guide. In addition, before you can make a Telnet connection to the router, you must have a valid host name for the router or have an IP address configured on the router. For more information about requirements for connecting to the router using Telnet, information about customizing your Telnet services, and using Telnet key sequences, see the Cisco IOS Configuration Fundamentals Configuration Guide.
In this syntax, host is the router hostname or an IP address, port is a decimal port number (23 is the default), and keyword is a supported keyword. For more information, see the Cisco IOS Configuration Fundamentals Command Reference Guide.
Note
If you are using an access server, then you will need to specify a valid port number such as telnet 172.20.52.40 2004, in addition to the hostname or IP address. The following example shows the telnet command to connect to the router named router:
unix_host% telnet router
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Step 2
At the password prompt, enter your login password. The following example shows entry of the password mypass:
User Access Verification Password: mypass
Note Step 3
If no password has been configured, press Return. From user EXEC mode, enter the enable command as shown in the following example:
Router> enable
Step 4
At the password prompt, enter your system password. The following example shows entry of the password enablepass:
Password: enablepass
Step 5
When the enable password is accepted, the privileged EXEC mode prompt appears:
Router#
Step 6 Step 7
You now have access to the CLI in privileged EXEC mode and you can enter the necessary commands to complete your desired tasks. To exit the Telnet session, use the exit or logout command as shown in the following example:
Router# logout
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Keystrokes Ctrl-B or the Left Arrow key1 Ctrl-F or the Right Arrow key1 Ctrl-A Ctrl-E Esc B Esc F
Purpose Move the cursor back one character Move the cursor forward one character Move the cursor to the beginning of the command line Move the cursor to the end of the command line Move the cursor back one word Move the cursor forward one word
Purpose Recall commands in the history buffer, beginning with the most recent command. Repeat the key sequence to recall successively older commands. Return to more recent commands in the history buffer after recalling commands with Ctrl-P or the Up Arrow key. While in EXEC mode, list the last several commands you have just entered.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Prompt
Router>
Exit Method Use the logout command. To return to user EXEC mode, use the disable command. To return to privileged EXEC mode from global configuration mode, use the exit or end command. To return to global configuration mode, use the exit command. To return to privileged EXEC mode, use the end command.
From user EXEC mode, use the enable EXEC Router# command. From privileged EXEC mode, use the configure terminal privileged EXEC command. From global configuration mode, specify an interface using an interface command.
Router(config)#
Interface configuration
Router(config-if)#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 7
Access Method The router boots up or accesses diagnostic mode in the following scenarios: In some cases, diagnostic mode will be reached when the IOS process or processes fail. In most scenarios, however, the router will reload. A user-configured access policy was configured using the transport-map command that directed the user into diagnostic mode. See the Console Port, Telnet, and SSH Handlingchapter of this book for information on configuring access policies. The router was accessed using a Route Processor auxiliary port. A break signal (Ctrl-C, Ctrl-Shift-6, or the send break command) was entered and the router was configured to go into diagnostic mode when the break signal was received.
Prompt
Router(diag)#
Exit Method If the IOS process failing is the reason for entering diagnostic mode, the IOS problem must be resolved and the router rebooted to get out of diagnostic mode. If the router is in diagnostic mode because of a transport-map configuration, access the router through another port or using a method that is configured to connect to the Cisco IOS CLI. If the router is accessed through the Route Processor auxiliary port, access the router through another port. Accessing the router through the auxiliary port is not useful for customer purposes anyway. To exit ROM monitor mode, use the continue command.
ROM monitor
> From privileged EXEC mode, use the reload EXEC command. Press the Break key during the first 60 seconds while the system is booting.
The IOS process or processes fail, in some scenarios. In other scenarios, the RP will simply reset when the IOS process or processes fail. A user-configured access policy was configured using the transport-map command that directs the user into diagnostic mode. The router was accessed using a Route Processor auxiliary port. A send break signal (Ctrl-C or Ctrl-Shift-6) was entered while accessing the router, and the router was configured to enter diagnostic mode when a break signal was sent.
In diagnostic mode, a subset of the commands that are also available in User EXEC mode are made available to users. Among other things, these commands can be used to:
Inspect various states on the router, including the IOS state. Replace or roll back the configuration. Provide methods of restarting the IOS or other processes. Reboot hardware, such as the entire router, an RP, an ESP, a SIP, a SPA, or possibly other hardware components.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Transfer files into or off of the router using remote access methods such as FTP, TFTP, SCP, and so on.
The diagnostic mode provides a more comprehensive user interface for troubleshooting than previous routers, which relied on limited access methods during failures, such as ROMmon, to diagnose and troubleshoot IOS problems. The diagnostic mode commands are stored in the nonIOS packages on the Cisco ASR 1000 Series Routers, which is why the commands are available even if the IOS process is not working properly. Importantly, all the commands available in diagnostic mode are also available in privileged EXEC mode on the router even during normal router operation. The commands are entered like any other commands in the privileged EXEC command prompts when used in privileged EXEC mode.
Getting Help
Entering a question mark (?) at the CLI prompt displays a list of commands available for each command mode. You can also get a list of keywords and arguments associated with any command by using the context-sensitive help feature. To get help specific to a command mode, a command, a keyword, or an argument, use one of the commands listed in Table 8:
Table 8 Help Commands and Purpose
Purpose Provides a brief description of the help system in any command mode. Provides a list of commands that begin with a particular character string. (No space between command and question mark.) Lists all commands available for a particular command mode. Lists the keywords or arguments that you must enter next on the command line. (Space between command and question mark.)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 9 shows examples of how you can use the question mark (?) to assist you in entering commands.
Table 9 Finding Command Options
Command
Router> enable Password: <password> Router#
Comment Enter the enable command and password to access privileged EXEC commands. You are in privileged EXEC mode when the prompt changes to a # from the >; for example, Router> to Router#. Enter the configure terminal privileged EXEC command to enter global configuration mode. You are in global configuration mode when the prompt changes to Router(config)#. Enter interface configuration mode by specifying the serial interface that you want to configure using the interface serial global configuration command. Enter ? to display what you must enter next on the command line. In this example, you must enter the serial interface slot number and port number, separated by a forward slash. When the <cr> symbol is displayed, you can press Enter to complete the command. You are in interface configuration mode when the prompt changes to Router(config-if)#.
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Router(config)# interface serial ? <0-6> Serial interface number Router(config)# interface serial 4 ? / Router(config)# interface serial 4/ ? <0-3> Serial interface number Router(config)# interface serial 4/0 ? <cr> Router(config)# interface serial 4/0 Router(config-if)#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 9
Command
Router(config-if)# ? Interface configuration commands: . . . ip Interface Internet Protocol config commands keepalive Enable keepalive lan-name LAN Name command llc2 LLC2 Interface Subcommands load-interval Specify interval for load calculation for an interface locaddr-priority Assign a priority group logging Configure logging for interface loopback Configure internal loopback on an interface mac-address Manually set interface MAC address mls mls router sub/interface commands mpoa MPOA interface configuration commands mtu Set the interface Maximum Transmission Unit (MTU) netbios Use a defined NETBIOS access list or enable name-caching no Negate a command or set its defaults nrzi-encoding Enable use of NRZI encoding ntp Configure NTP . . . Router(config-if)# Router(config-if)# ip ? Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit broadcast-address Set the broadcast address of an interface cgmp Enable/disable CGMP directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time . . . Router(config-if)# ip
Comment Enter ? to display a list of all the interface configuration commands available for the serial interface. This example shows only some of the available interface configuration commands.
Enter the command that you want to configure for the interface. This example uses the ip command. Enter ? to display what you must enter next on the command line. This example shows only some of the available interface IP configuration commands.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Using Cisco IOS XE Software Using the no and default Forms of Commands
Table 9
Command
Router(config-if)# ip address ? A.B.C.D IP address negotiated IP Address negotiated over PPP Router(config-if)# ip address
Comment Enter the command that you want to configure for the interface. This example uses the ip address command. Enter ? to display what you must enter next on the command line. In this example, you must enter an IP address or the negotiated keyword. A carriage return (<cr>) is not displayed; therefore, you must enter additional keywords or arguments to complete the command.
Enter the keyword or argument that you want to use. This example uses the 172.16.0.1 IP address. Enter ? to display what you must enter next on the command line. In this example, you must enter an IP subnet mask. A <cr> is not displayed; therefore, you must enter additional keywords or arguments to complete the command.
Router(config-if)# ip address 172.16.0.1 255.255.255.0 ? secondary Make this IP address a secondary address <cr> Router(config-if)# ip address 172.16.0.1 255.255.255.0
Enter the IP subnet mask. This example uses the 255.255.255.0 IP subnet mask. Enter ? to display what you must enter next on the command line. In this example, you can enter the secondary keyword, or you can press Enter. A <cr> is displayed; you can press Enter to complete the command, or you can enter another keyword.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
It might take a minute or two to save the configuration. After the configuration has been saved, the following output appears:
[OK] Router#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Using Cisco IOS XE Software Filtering the Output of the show and more Commands
12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw7516 Jul 2 2008 15:01:39 -07:00 startup-config
For more detailed information on managing configuration files, see the Managing Configuration Files section in the Cisco IOS XE Configuration Fundamentals Configuration Guide.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
show command | {append | begin | exclude | include | redirect | section | tee} regular-expression The output matches certain lines of information in the configuration file. The following example illustrates how to use output modifiers with the show interface command when you want the output to include only lines in which the expression protocol appears:
Router# show interface | include protocol FastEthernet0/0 is up, line protocol is up Serial4/0 is up, line protocol is up Serial4/1 is up, line protocol is up Serial4/2 is administratively down, line protocol is down Serial4/3 is administratively down, line protocol is down
Place the power supply switch in the Off position after seeing this message.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Using Cisco IOS XE Software Finding Support Information for Platforms and Cisco Software Images
Platform support information Memory recommendations New feature information Open and resolved severity 1 and 2 caveats for all platforms
Release notes are intended to be release-specific for the most current release, and the information provided in these documents may not be cumulative in providing information about features that first appeared in previous releases. Refer to Cisco Feature Navigator for cumulative feature information.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Using Cisco IOS XE Software Finding Support Information for Platforms and Cisco Software Images
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Console Port Overview for the Cisco ASR 1000 Series Routers, page 1 Console Port Handling Overview, page 1 Telnet and SSH Overview for the Cisco ASR 1000 Series Routers, page 2 Persistent Telnet and Persistent SSH Overview, page 2 Configuring a Console Port Transport Map, page 3 Configuring Persistent Telnet, page 5 Configuring Persistent SSH, page 8 Viewing Console Port, SSH, and Telnet Handling Configurations, page 11 Important Notes and Restrictions, page 16
Console Port Overview for the Cisco ASR 1000 Series Routers
The console port on the Cisco ASR 1000 Series Router is an EIA/TIA-232 asynchronous, serial connection with no flow control and an RJ-45 connector. The console port is used to access the router and is located on the front panel of the Route Processor (RP). For information on accessing the router using the console port, see the Accessing the CLI Using a Directly-Connected Console section on page 2.
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Console Port, Telnet, and SSH Handling Telnet and SSH Overview for the Cisco ASR 1000 Series Routers
These settings can be changed by configuring a transport map for the console port and applying that transport map to the console interface.
Telnet and SSH Overview for the Cisco ASR 1000 Series Routers
Telnet and Secure Shell (SSH) on the Cisco ASR 1000 Series Routers can be configured and handled like Telnet and SSH on other Cisco platforms. For information on traditional Telnet, see the line command in the Cisco IOS Terminal Services Command Reference guide located at: http://www.cisco.com/en/US/docs/ios/12_2/termserv/command/reference/trflosho.html#wp1029818. For information on configuring traditional SSH, see the Configuring Secure Shell chapter of the Cisco IOS Security Configuration Guide located at: http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/scfssh.html. The Cisco ASR 1000 Series Routers also introduces persistent Telnet and persistent SSH. Persistent Telnet and persistent SSH allow network administrators to more clearly define the treatment of incoming traffic when users access the router through the Management Ethernet port using Telnet or SSH. Notably, persistent Telnet and persistent SSH provide more robust network access by allowing the router to be configured to be accessible through the Ethernet Management port using Telnet or SSH even when the IOS process has failed.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Console Port, Telnet, and SSH Handling Configuring a Console Port Transport Map
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7.
(Required) enable (Required) configure terminal (Required) transport-map type console transport-map-name (Required) connection wait [allow interruptible | none {disconnect}] (Optional) banner [diagnostic | wait] banner-message (Required) exit (Required) transport type console console-line-number input transport-map-name
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Creates and names a transport map for handling console connections, and enter transport map configuration mode.
Example:
Router(config)# transport-map type console consolehandler
Step 4
Specifies how a console connection will be handled using this transport map:
Example:
Router(config-tmap)# connection wait none
allow interruptibleThe console connection waits for an IOS vty line to become available, and also allows user to enter diagnostic mode by interrupting a console connection waiting for the IOS vty line to become available. This is the default setting.
Note
Users can interrupt a waiting connection by entering Ctrl-C or Ctrl-Shift-6. noneThe console connection immediately enters diagnostic mode.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Console Port, Telnet, and SSH Handling Configuring a Console Port Transport Map
Command or Action
Step 5
banner [diagnostic | wait] banner-message
Purpose (Optional) Creates a banner message that will be seen by users entering diagnostic mode or waiting for the IOS vty line as a result of the console transport map configuration.
Example:
Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. --Welcome to Diagnostic Mode-X Router(config-tmap)#
diagnosticCreates a banner message seen by users directed into diagnostic mode as a result of the console transport map configuration. waitCreates a banner message seen by users waiting for the IOS vty to become available. banner-messageThe banner message, which begins and ends with the same delimiting character.
Step 6
exit
Example:
Router(config-tmap)# exit
Step 7
Applies the settings defined in the transport map to the console interface. The transport-map-name for this command must match the transport-map-name defined in the transport-map type console command.
Example:
Router(config)# transport type console 0 input consolehandler
Examples
In the following example, a transport map to set console port access policies is created and attached to console port 0:
Router(config)# transport-map type console consolehandler Router(config-tmap)# connection wait allow interruptible Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. Welcome to diagnostic mode X Router(config-tmap)# banner wait X Enter TEXT message. End with the character 'X'. Waiting for IOS vty line X Router(config-tmap)# exit Router(config)# transport type console 0 input consolehandler
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Prerequisites
For a persistent Telnet connection to access an IOS vty line on the Cisco ASR 1000 Series Router, local login authentication must be configured for the vty line (the login command in line configuration mode). If local login authentication is not configured, users will not be able to access IOS using a Telnet connection into the Management Ethernet interface with an applied transport map. Diagnostic mode will still be accessible in this scenario.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
(Required) enable (Required) configure terminal (Required) transport-map type persistent telnet transport-map-name (Required) connection wait [allow {interruptible} | none {disconnect}] (Optional) banner [diagnostic | wait] banner-message (Required) transport interface GigabitEthernet 0 (Required) exit (Required) transport type persistent telnet input transport-map-name
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Creates and names a transport map for handling persistent Telnet connections, and enters transport map configuration mode.
Example:
Router(config)# transport-map type persistent telnet telnethandler
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command or Action
Step 4
connection wait [allow {interruptible}| none {disconnect}]
Purpose Specifies how a persistent Telnet connection will be handled using this transport map:
Example:
Router(config-tmap)# connection wait none
allowThe Telnet connection waits for an IOS vty line to become available, and exits the router if interrupted. allow interruptibleThe Telnet connection waits for the IOS vty line to become available, and also allows user to enter diagnostic mode by interrupting a Telnet connection waiting for the IOS vty line to become available. This is the default setting.
Note
Users can interrupt a waiting connection by entering Ctrl-C or Ctrl-Shift-6. noneThe Telnet connection immediately enters diagnostic mode. none disconnectThe Telnet connection does not wait for the IOS vty line and does not enter diagnostic mode, so all Telnet connections are rejected if no vty line is immediately available in IOS.
Step 5
Example:
Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. --Welcome to Diagnostic Mode-X Router(config-tmap)#
(Optional) Creates a banner message that will be seen by users entering diagnostic mode or waiting for the IOS vty line as a result of the persistent Telnet configuration.
diagnosticcreates a banner message seen by users directed into diagnostic mode as a result of the persistent Telnet configuration. waitcreates a banner message seen by users waiting for the vty line to become available. banner-messagethe banner message, which begins and ends with the same delimiting character.
Step 6
Applies the transport map settings to the Management Ethernet interface (interface gigabitethernet 0). Persistent Telnet can only be applied to the Management Ethernet interface on the Cisco ASR 1000 Series Routers. This step must be taken before applying the transport map to the Management Ethernet interface.
Example:
Router(config-tmap)# transport interface gigabitethernet 0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command or Action
Step 7
exit
Purpose Exits transport map configuration mode to re-enter global configuration mode.
Example:
Router(config-tmap)# exit
Step 8
Applies the settings defined in the transport map to the Management Ethernet interface. The transport-map-name for this command must match the transport-map-name defined in the transport-map type persistent telnet command.
Example:
Router(config)# transport type persistent telnet input telnethandler
Examples
In the following example, a transport map that will make all Telnet connections wait for an IOS vty line to become available before connecting to the router, while also allowing the user to interrupt the process and enter diagnostic mode, is configured and applied to the Management Ethernet interface (interface gigabitethernet 0). A diagnostic and a wait banner are also configured. The transport map is then applied to the interface when the transport type persistent telnet input command is entered to enable persistent Telnet.
Router(config)# transport-map type persistent telnet telnethandler Router(config-tmap)# connection wait allow interruptible Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. --Welcome to Diagnostic Mode-X Router(config-tmap)# banner wait X Enter TEXT message. End with the character 'X'. --Waiting for IOS Process-X Router(config-tmap)# transport interface gigabitethernet 0 Router(config-tmap)# exit Router(config)# transport type persistent telnet input telnethandler
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
(Required) enable (Required) configure terminal (Required) transport-map type persistent ssh transport-map-name (Required) connection wait [allow {interruptible} | none {disconnect}] (Required) rsa keypair-name rsa-keypair-name (Optional) authentication-retries number-of-retries (Optional) banner [diagnostic | wait] banner-message (Optional) time-out timeout-interval-in-seconds (Required) transport interface GigabitEthernet 0
10. (Required) exit 11. (Required) transport type persistent ssh input transport-map-name
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Creates and names a transport map for handling persistent SSH connections, and enters transport map configuration mode.
Example:
Router(config)# transport-map type persistent ssh sshhandler
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command or Action
Step 4
connection wait [allow {interruptible}| none {disconnect}]
Purpose Specifies how a persistent SSH connection will be handled using this transport map:
Example:
Router(config-tmap)# connection wait allow interruptible
allowThe SSH connection waits for the vty line to become available, and exits the router if interrupted. allow interruptibleThe SSH connection waits for the vty line to become available, and also allows users to enter diagnostic mode by interrupting a SSH connection waiting for the vty line to become available. This is the default setting.
Note
Users can interrupt a waiting connection by entering Ctrl-C or Ctrl-Shift-6. noneThe SSH connection immediately enters diagnostic mode. none disconnectThe SSH connection does not wait for the vty line from IOS and does not enter diagnostic mode, so all SSH connections are rejected if no vty line is immediately available.
Step 5
Names the RSA keypair to be used for persistent SSH connections. For persistent SSH connections, the RSA keypair name must be defined using this command in transport map configuration mode. The RSA keypair definitions defined elsewhere on the router, such as through the use of the ip ssh rsa keypair-name command, do not apply to persistent SSH connections. No rsa-keypair-name is defined by default. (Optional) Specifies the number of authentication retries before dropping the connection. The default number-of-retries is 3. (Optional) Creates a banner message that will be seen by users entering diagnostic mode or waiting for the vty line as a result of the persistent SSH configuration.
Example:
Router(config-tmap)# rsa keypair-name sshkeys
Step 6
authentication-retries number-of-retries
Example:
Router(config-tmap)# authentication-retries 4
Step 7
Example:
Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. --Welcome to Diagnostic Mode-X Router(config-tmap)#
diagnosticCreates a banner message seen by users directed into diagnostic mode as a result of the persistent SSH configuration. waitCreates a banner message seen by users waiting for the vty line to become active. banner-messageThe banner message, which begins and ends with the same delimiting character.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command or Action
Step 8
time-out timeout-interval
Purpose (Optional) Specifies the SSH time-out interval in seconds. The default timeout-interval is 120 seconds.
Example:
Router(config-tmap)# time-out 30
Step 9
Applies the transport map settings to the Management Ethernet interface (interface gigabitethernet 0). Persistent SSH can only be applied to the Management Ethernet interface on the Cisco ASR 1000 Series Routers. Exits transport map configuration mode to re-enter global configuration mode.
Example:
Router(config-tmap)# transport interface gigabitethernet 0
Step 10
exit
Example:
Router(config-tmap)# exit
Step 11
Applies the settings defined in the transport map to the Management Ethernet interface. The transport-map-name for this command must match the transport-map-name defined in the transport-map type persistent ssh command.
Example:
Router(config)# transport type persistent ssh input sshhandler
Examples
In the following example, a transport map that will make all SSH connections wait for the vty line to become active before connecting to the router is configured and applied to the Management Ethernet interface (interface gigabitethernet 0). The RSA keypair is named sshkeys. This example only uses the commands required to configure persistent SSH.
Router(config)# transport-map type persistent ssh sshhandler Router(config-tmap)# connection wait allow Router(config-tmap)# rsa keypair-name sshkeys Router(config-tmap)# transport interface gigabitethernet 0
In the following example, a transport map is configured that will apply the following settings to any users attempting to access the Management Ethernet port via SSH:
Users using SSH will wait for the vty line to become active, but will enter diagnostic mode if the attempt to access IOS through the vty line is interrupted. The RSA keypair name is sshkeys The connection allows one authentication retry. The banner --Welcome to Diagnostic Mode-- will appear if diagnostic mode is entered as a result of SSH handling through this transport map. The banner --Waiting for vty line-- will appear if the connection is waiting for the vty line to become active.
The transport map is then applied to the interface when the transport type persistent ssh input command is entered to enable persistent SSH:
Router(config)# transport-map type persistent ssh sshhandler Router(config-tmap)# connection wait allow interruptible
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Console Port, Telnet, and SSH Handling Viewing Console Port, SSH, and Telnet Handling Configurations
Router(config-tmap)# rsa keypair-name sshkeys Router(config-tmap)# authentication-retries 1 Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. --Welcome to Diagnostic Mode-X Router(config-tmap)#banner wait X Enter TEXT message. End with the character 'X'. --Waiting for vty line-X Router(config-tmap)# time-out 30 Router(config-tmap)# transport interface gigabitethernet 0 Router(config-tmap)# exit Router(config)# transport type persistent ssh input sshhandler
Transport Map: Name: sshhandler Type: Persistent SSH Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS prompt Bshell banner: Welcome to Diagnostic Mode
SSH:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Console Port, Telnet, and SSH Handling Viewing Console Port, SSH, and Telnet Handling Configurations
Timeout: 120 Authentication retries: 5 RSA keypair: sshkeys Transport Map: Name: telnethandler Type: Persistent Telnet Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS process Bshell banner: Welcome to Diagnostic Mode
Transport Map: Name: telnethandling1 Type: Persistent Telnet Transport Connection: Wait option: Wait Allow
Router# show transport-map type console Transport Map: Name: consolehandler Type: Console Transport Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for the IOS CLI Bshell banner: Welcome to Diagnostic Mode
Router# show transport-map type persistent ssh Transport Map: Name: sshhandler Type: Persistent SSH Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS prompt Bshell banner: Welcome to Diagnostic Mode
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Console Port, Telnet, and SSH Handling Viewing Console Port, SSH, and Telnet Handling Configurations
SSH: Timeout: 120 Authentication retries: 5 RSA keypair: sshkeys Router# show transport-map type persistent telnet Transport Map: Name: telnethandler Type: Persistent Telnet Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS process Bshell banner: Welcome to Diagnostic Mode
Transport Map: Name: telnethandling1 Type: Persistent Telnet Transport Connection: Wait option: Wait Allow
Router# show transport-map name telnethandler Transport Map: Name: telnethandler Type: Persistent Telnet Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS process Bshell banner: Welcome to Diagnostic Mode
Router# show transport-map name consolehandler Transport Map: Name: consolehandler Type: Console Transport Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for the IOS CLI Bshell banner:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Console Port, Telnet, and SSH Handling Viewing Console Port, SSH, and Telnet Handling Configurations
Router# show transport-map name sshhandler Transport Map: Name: sshhandler Type: Persistent SSH Transport Interface: GigabitEthernet0 Connection: Wait option: Wait Allow Interruptable Wait banner: Waiting for IOS prompt Bshell banner: Welcome to Diagnostic Mode
The show platform software configuration access policy command can be used to view the current configurations for the handling of incoming console port, SSH, and Telnet connections. The output of this command provides the current wait policy for each type of connection, as well as any information on the currently configured banners. Unlike show transport-map, this command is available in diagnostic mode so it can be entered in cases when you need transport map configuration information but cannot access the IOS CLI.
Router# show platform software configuration access policy The current access-policies Method : telnet Rule : wait Shell banner: Wait banner : Method : ssh Rule : wait Shell banner: Wait banner : Method : console Rule : wait with interrupt Shell banner: Wait banner :
In the following example, the connection policy and banners are set for a persistent SSH transport map, and the transport map is enabled. The show platform software configuration access policy output is given both before the new transport map is enabled and after the transport map is enabled so the changes to the SSH configuration are illustrated in the output.
Router# show platform software configuration access policy
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Console Port, Telnet, and SSH Handling Viewing Console Port, SSH, and Telnet Handling Configurations
The current access-policies Method : telnet Rule : wait with interrupt Shell banner: Welcome to Diagnostic Mode Wait banner : Waiting for IOS Process
Method : ssh Rule : wait Shell banner: Wait banner : Method : console Rule : wait with interrupt Shell banner: Wait banner :
Router(config)# transport-map type persistent ssh sshhandler Router(config-tmap)# connection wait allow interruptible Router(config-tmap)# banner diagnostic X Enter TEXT message. End with the character 'X'. Welcome to Diag Mode X Router(config-tmap)# banner wait X Enter TEXT message. End with the character 'X'. Waiting for IOS X Router(config-tmap)# rsa keypair-name sshkeys Router(config-tmap)# transport interface gigabitethernet 0 Router(config-tmap)# exit Router(config)# transport type persistent ssh input sshhandler Router(config)# exit Router# show platform software configuration access policy The current access-policies Method : telnet Rule : wait with interrupt Shell banner: Welcome to Diagnostic Mode Wait banner : Waiting for IOS process
Method : ssh Rule : wait with interrupt Shell banner: Welcome to Diag Mode Wait banner : Waiting for IOS
Method
: console
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Console Port, Telnet, and SSH Handling Important Notes and Restrictions
The Telnet and SSH settings made in the transport map override any other Telnet or SSH settings when the transport map is applied to the Management Ethernet interface. Only local usernames and passwords can be used to authenticate users entering a Management Ethernet interface. AAA authentication is not available for users accessing the router through a Management Ethernet interface using persistent Telnet or persistent SSH. Applying a transport map to a Management Ethernet interface with active Telnet or SSH sessions can disconnect the active sessions. Removing a transport map from an interface, however, does not disconnect any active Telnet or SSH sessions. Configuring the diagnostic and wait banners is optional but recommended. The banners are especially useful as indicators to users of the status of their Telnet or SSH attempts.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Running the Cisco ASR 1000 Series Routers: An Overview, page 1 Software File Management Using Command Sets, page 4 Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages, page 6 Upgrading Individual SubPackages, page 18
Note
This section of the document does not discuss limited downtime upgrades. For information on limited downtime upgrades, see the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers section on page 1.
Running the Cisco ASR 1000 Series Routers Using Individual and Optional SubPackages: An Overview, page 2 Running the Cisco ASR 1000 Series Routers Using a Consolidated Package: An Overview, page 2 Running the Cisco ASR 1000 Series Routers: A Summary, page 3
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Consolidated Packages and SubPackages Management Running the Cisco ASR 1000 Series Routers: An Overview
Running the Cisco ASR 1000 Series Routers Using Individual and Optional SubPackages: An Overview
The Cisco ASR 1000 Series Routers can be configured to run using individual subpackages and optional subpackages. When the router is configured to run using individual and optional subpackages:
Each individual subpackage within a consolidated package is extracted onto the router as its own file. Additionally, any optional subpackages must be separately downloaded and stored in the same directory with the provisioning file and the other individual subpackages that have been extracted. The router then runs by accessing each file as needed for operational purposes. All individual and optional subpackage files must be stored in the same directory on the router for the router to run properly using individual subpackages.
When a Cisco ASR 1000 Series Router is configured to run using individual and optional subpackages, software image content from the RP is copied into memory on an as-needed basis only. Memory is conserved for other router processes, such as passing traffic. The router, therefore, allows for the highest peak traffic load when configured to run using individual subpackages. When running the Cisco ASR 1000 Series Routers using individual and optional subpackages, the router must be configured to boot using the provisioning file that was included in the consolidated package with the individual subpackage files. This provisioning file must also be in the same directory as the individual and optional subpackage files. The router boots faster when configured to run using individual and optional subpackages than it does when configured to run using a consolidated package. A Cisco ASR 1000 Series Router cannot be configured to run individual and optional subpackages stored on a TFTP or any other network server. The individual and optional subpackages along with the provisioning file must be copied onto the bootflash: file system to run the router using this method.
Running the Cisco ASR 1000 Series Routers Using a Consolidated Package: An Overview
The Cisco ASR 1000 Series Routers can also be configured to run using a consolidated package.
Note
Booting the router from a consolidated package is not supported for installation of optional subpackages. For more information, see the Running the Cisco ASR 1000 Series Routers Using Individual and Optional SubPackages: An Overview section on page 2. When the router is configured to run using a consolidated package, the entire consolidated package file is copied onto the router or accessed by the router via TFTP or another network transport method. The router runs using the consolidated package file. When a Cisco ASR 1000 Series Router is configured to run using the consolidated package file, more memory is required to process router requests because the router has to search one larger file for every request. The peak amount of memory available for passing network traffic is therefore lower when the router is configured to run using a consolidated package. A Cisco ASR 1000 Series Router configured to run using a consolidated package is booted by booting the consolidated package file. Because this file is large, the boot process for routers running using the consolidated package is slower than the boot process for routers running individual subpackages.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Running the Cisco ASR 1000 Series Routers: An Overview
A Cisco ASR 1000 Series Router configured to run using a consolidated package does have some advantages over a Cisco ASR 1000 Series Router configured to run individual subpackages. First, a consolidated package can be booted and utilized using TFTP or another network transport method. Secondly, configuring the router to use the one consolidated package file is easier than managing several individual subpackage files. Running the router using a consolidated package may be the right method of running the router in certain networking environments. The consolidated package should be stored on bootflash:, usb[0-1]:, or a remote file system when this method is used to run the router.
Optimizes router memory usageWhen the router is booting using the individual and optional subpackage method, software image content from the Router Processor (RP) is copied into memory on an as-needed basis only, which conserves memory for other router processes. The router boots fastest and allows for the highest peak traffic load when booted using the individual subpackage boot approach. Simplified installationOnly one software file needs to be managed instead of several separate images. StorageA consolidated package, unlike individual subpackages, can be used to run the router while being stored in bootflash:, on a USB Flash disk, or on a network server. A consolidated package can be booted and utilized using TFTP or another network transport method, while the individual subpackage method requires the individual subpackage files to be copied into the bootflash: file directory on the router.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Software File Management Using Command Sets
Advantages
Disadvantages
This method is required if you need to install any optional subpackages for your system.
Optimizes memory usage, allowing for faster boot times and increased traffic loads.
Multiple software subpackages more difficult to manage. Cannot be booted from TFTP or any other network server. If you are going to use the individual subpackage boot method, each individual subpackage file must be placed in the bootflash: directory. Individual and optional subpackage files and the provisioning file must be stored in bootflash:. Slower boot times and lessened maximum system scalability because the larger image must be processed at all times.
Consolidated Package
Easier management. Only have to manage one file instead of many files. A consolidated package file can be stored in bootflash:, on a USB Flash disk, or on any TFTP or other network server.
The request platform Command Set, page 4 The copy Command, page 5 The issu Command Set, page 5
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Software File Management Using Command Sets
The request platform software package command requires that the destination device or process be specified in the command line, so the commands can be used to upgrade software on both an active or a standby processor. The request platform software package command allows for no downtime software upgrades in many scenarios. The basic syntax of the command is request platform software package install rp rp-slot-number file file-URL, where rp-slot-number is the number of the RP slot and file-URL is the path to the file being used to upgrade the Cisco ASR 1000 Series Router. The command has other options; see the request platform software package command references for information on all of the options available with this command set. In Cisco IOS XE Release 2.4, the request platform software package uninstall command is introduced on the Cisco ASR 1000 Series Routers to remove provisioning of an optional subpackage from an RP. The syntax for the command follows the install form of the command: request platform software package uninstall rp rp-slot-number type pkg, where rp-slot-number is the number of the RP slot and pkg is the type of optional subpackage file to be removed.
Note
For additional information on limited downtime upgrades using the request platform software package command set, see the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers section on page 1.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
A confirm prompt is displayed when the command issu abortversion is issued and when the standby has not reached the terminal (hot) state. The following example shows a confirm prompt notification:
The system is without a fully initialized peer and service impact will occur. Proceed with abort? [confirm]
The issu runversion command is optional for completing a consolidated package upgrade on the Cisco ASR 1000 Series Routers. You can enter issu commitversion from the active RP to complete the software upgrade, then use the redundancy force-switchover command to switch to the upgraded RP on this platform, if desired.
Note
For additional information on limited downtime upgrades using the issu command set, see the Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers section on page 1.
Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
This section discusses the following topics:
Quick Start Software Upgrade, page 6 Managing and Configuring a Router to Run Using a Consolidated Package, page 7 Managing and Configuring a Router to Run Using Individual SubPackages From a Consolidated Package, page 10 Managing and Configuring a Router to Run Using Optional SubPackages, page 14 Troubleshooting Software Mismatch with ESP Board ASR1000-ESP10-N, page 18
Copy the consolidated package into bootflash: using the copy URL-to-image bootflash: command. If you want to run the router using individual subpackages, enter the request platform software package expand file bootflash:image-name command. If you want to run the router using a consolidated package, skip this step. Enter the dir bootflash: command to verify your consolidated package or your extracted subpackages are in the directory.
Step 3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
Step 4 Step 5
If you are trying to run individual subpackages, use the delete bootdisk:image-name to delete the consolidated package. If you want to run the router using the consolidated package, skip this step. Set up the boot parameters for your boot. Set the configuration register to 0x2 by entering the config-register 0x2102 global configuration command, and enter the boot system flash bootflash:image-name (if running using the consolidated package) or boot system flash bootflash:provisionging-file-name (if running using individual subpackages) global configuration command. Enter copy running-config startup-config to save your configuration. Enter the reload command to reload the router and finish the boot. The upgraded software should be running when the reload completes.
Step 6 Step 7
Do not use this procedure if you also need to install any optional subpackages. This section documents the following procedures:
Managing and Configuring a Consolidated Package Using the copy Command, page 7 Managing and Configuring a Consolidated Package Using the request platform software package install Command, page 8
928862208 bytes total (712273920 bytes free) Router# copy tftp bootflash: Address or name of remote host []? 172.17.16.81 Source filename []? /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Destination filename [asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
Accessing tftp://172.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.b in... Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!! [OK - 208904396 bytes] 208904396 bytes copied in 330.453 secs (632176 bytes/sec) Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 lost+found .ssh .rollback_timer .prst_sync .installer
target_support_output.tgz.tgz
928862208 bytes total (503156736 bytes free) Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#boot system flash bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Router(config)#config-reg 0x2102 Router(config)#exit Router#show run | include boot boot-start-marker boot system flash bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin boot-end-marker Router# copy run start Destination filename [startup-config]? Building configuration... [OK] Router# reload
Managing and Configuring a Consolidated Package Using the request platform software package install Command
In the following example, the request platform software package install command is used to upgrade a consolidated package running on RP 0. The force option, which forces the upgrade past any prompt (such as already having the same consolidated package installed), is used in this example.
Router# request platform software package install rp 0 file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
--- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Extracting super package content Verifying parameters Validating package type Copying package files Checking and verifying packages contained in super package Creating candidate provisioning file WARNING: WARNING: Candidate software will be installed upon reboot WARNING: Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility with running software Checking IPC compatibility with running software ... skipped Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. Router# reload New software will load on reboot.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
Note
A reload must be performed to finish this procedure. The Managing and Configuring a Consolidated Package Using the copy Command section on page 7 includes an example of how to configure the router to boot using the consolidated package, and then an example of what happens after the reload is performed to finish the installation.
Managing and Configuring a Router to Run Using Individual SubPackages From a Consolidated Package
To run the router using individual subpackages from a consolidated package, follow one of the following procedures:
Extracting a Consolidated Package and Booting Using the Provisioning File, page 10 Copying a Set of Individual SubPackage Files, and Booting Using a Provisioning File, page 14
Copy the consolidated package file (or, in cases where you have every individual subpackage and a provisioning file for the subpackages available, each individual subpackage and the provisioning file) onto the bootflash: file system using the copy command. Make sure to copy the consolidated package into the bootflash: file system and directory where you want to store the provisioning file and the individual image subpackages. Enter the request platform software package expand file bootflash:url-to-Cisco-IOS-XE-imagename command with no other option to extract the provisioning file and the individual subpackages out of the consolidated package file and into the current directory in bootflash:. Copy the consolidated package file onto any file system on your router, then enter the request platform software package expand file file-system:url-to-Cisco-IOS-XE-imagename to bootflash: command to extract the provisioning file and the individual image subpackages onto the bootflash: file system.
Note
After performing this step, do not move any of the files. The bootup process cannot function properly unless all of the subpackages and the provisioning file are located in the same directory. Also, do not rename the subpackage files. Only the provisioning file can be renamed, and the renaming of the provisioning file, if desired, should be done at this step before the router is rebooted. Configure the router to boot using the provisioning file. The sequence below provides an example that would boot the router using the provisioning file named packages.conf that was stored with the other subpackages in the bootflash: file system:
Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit *May 11 01:31:04.815: %SYS-5-CONFIG_I: Configured from console by con Router# copy running-config startup-config
Step 2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
The following example shows how to extract the individual subpackages and the provisioning file from a consolidated package that has already been placed in the directory where you want to store the individual subpackages and the provisioning file. Output of the directory before and after the extraction is given to confirm the files were extracted.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 928862208 bytes total (503156736 bytes free) Router# request platform software package expand file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 57611 -rw47071436 May 22 2008 11:26:23 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw5740 May 22 2008 11:26:22 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57612 -rw20334796 May 22 2008 11:26:24 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57613 -rw22294732 May 22 2008 11:26:24 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 57614 -rw21946572 May 22 2008 11:26:25 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57615 -rw48099532 May 22 2008 11:26:26 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57616 -rw34324684 May 22 2008 11:26:27 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg 57617 -rw22124748 May 22 2008 11:26:28 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 57603 -rw6256 May 22 2008 11:26:28 -07:00 packages.conf 13 -rw45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz lost+found .ssh .rollback_timer .prst_sync .installer
target_support_output.tgz.tgz
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
The following example shows how to extract the individual subpackages and the provisioning file from a consolidated package that has already been placed on the router in a directory that will not store the individual subpackages and the provisioning file. In this particular example, the contents of a consolidated package stored in usb0: are extracted into bootflash:. Output of the bootflash: directory before and after the extraction is given to confirm the files were extracted:
Router# dir usb0: Directory of usb0:/ 1240 -rwx 208904396 May 27 2008 14:10:20 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 255497216 bytes total (40190464 bytes free) Router# dir bootflash: Directory of bootflash:/ 11 87937 14657 29313 12 58625 drwx drwx drwx drwx -rwdrwx 16384 4096 4096 4096 33554432 4096 Dec 13 Dec 13 Dec 13 Dec 13 Dec 13 May 7 2004 2004 2004 2004 2004 2008 03:45:47 03:46:45 03:47:17 03:53:00 03:53:49 17:27:51 -08:00 -08:00 -08:00 -08:00 -08:00 -07:00 lost+found .rollback_timer .installer .ssh nvram_00100 .prst_sync
945377280 bytes total (695246848 bytes free) Router# request platform software package expand file usb0:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin to bootflash: Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 13 2004 03:45:47 -08:00 lost+found 87937 drwx 4096 Dec 13 2004 03:46:45 -08:00 .rollback_timer 14657 drwx 4096 Dec 13 2004 03:47:17 -08:00 .installer 29313 drwx 4096 Dec 13 2004 03:53:00 -08:00 .ssh 12 -rw33554432 Dec 13 2004 03:53:49 -08:00 nvram_00100 43979 -rw47071436 May 27 2008 14:25:01 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 58625 drwx 4096 May 7 2008 17:27:51 -07:00 .prst_sync 43970 -rw5740 May 27 2008 14:25:00 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 43980 -rw20334796 May 27 2008 14:25:01 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 43981 -rw22294732 May 27 2008 14:25:02 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 43982 -rw21946572 May 27 2008 14:25:03 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 43983 -rw48099532 May 27 2008 14:25:04 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 43984 -rw34324684 May 27 2008 14:25:05 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
43985 -rw22124748 May 27 2008 14:25:05 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 43971 -rw6256 May 27 2008 14:25:05 -07:00 945377280 bytes total (478752768 bytes free)
packages.conf
Extracting the SubPackages, Configuring the Router to Boot Using the Provisioning File, and Reloading the Router: Example 3
In the following example, the provisioning file and the individual subpackages are extracted from a consolidated package. The router is then configured to boot using the provisioning file. This example also shows the config-register being set and the running configuration being saved because these tasks must be performed for the router to reload properly. The router is then reloaded to complete the process.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 928862208 bytes total (503156736 bytes free) Router# request platform software package expand file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 57611 -rw47071436 May 22 2008 11:26:23 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw5740 May 22 2008 11:26:22 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57612 -rw20334796 May 22 2008 11:26:24 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57613 -rw22294732 May 22 2008 11:26:24 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 57614 -rw21946572 May 22 2008 11:26:25 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57615 -rw48099532 May 22 2008 11:26:26 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57616 -rw34324684 May 22 2008 11:26:27 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg 57617 -rw22124748 May 22 2008 11:26:28 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg lost+found .ssh .rollback_timer .prst_sync .installer
target_support_output.tgz.tgz
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
57603 13
-rw-rw-
6256 45977
packages.conf target_support_output.tgz.tgz
928862208 bytes total (286662656 bytes free) Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit Router# copy run start Router# reload
Copying a Set of Individual SubPackage Files, and Booting Using a Provisioning File
To copy a set of individual subpackage files and to boot using a provisioning file, perform the following steps:
Note
Although this upgrade method works, it is less efficient than other methods of upgrading the routers software. Copy each individual subpackage and the provisioning file into the bootflash: directory using the copy command. Note that this method of running the router will only work if all the individual subpackages for a release and a provisioning file are downloaded onto the router and stored in the bootflash: directory. No other file directories should be used for booting the router using individual subpackages. The files can also be moved on the router physically using a USB Flash drive.
Step 1
Step 2
Configure the router to boot using the provisioning file. The sequence below provides an example that describes how to boot the router using the provisioning file named packages.conf that was stored with the other subpackages in the bootflash: file system. The router runs using individual subpackages once the reload is complete.
Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit *May 11 01:31:04.815: %SYS-5-CONFIG_I: Configured from console by con Router# write memory Building configuration... [OK] Router# reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
If you install the Cisco WebEx Node for ASR 1000 Series SPA before the software subpackage is installed, you will receive the error message %ASR1000_RP_SPA-3-MISSING_SPA_PKG_ERR. This message will resolve once you download and install the appropriate sipspawma subpackage and then reload the router in individual subpackage mode. To run the router using an optional subpackage, perform the following steps for each RP in the system:
Step 1
Verify that the RP is running in individual subpackage mode and was booted from a provisioning file. For more information, see the Managing and Configuring a Router to Run Using Individual SubPackages From a Consolidated Package section on page 10. Verify that the version of the optional subpackage that you want to install is the same version as the software running on the active RP. Download the optional subpackage that you want to install. Optional subpackages must be downloaded independently from consolidated packages for the Cisco ASR 1000 Series Routers. On each RP, copy the optional subpackage to the directory where any other individual subpackages and the provisioning file is located. Run the request platform software package install rp file command, as shown in the following example.
Note
Do not use the optional slot or bay keywords for the initial installation.
Router# request platform software package install rp 0 file bootflash:asr1000rp1-sipspawmak9.BLD_V122_33_XND_ASR_RLS4_THROTTLE_LATEST_20090511_042308. pkg --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting file path checking --Finished file path checking --- Starting image file verification --- Checking image file names Verifying image file locations Locating image files and validating name syntax Found asr1000rp1sipspawmak9.BLD_V122_33_XND_ASR_RLS4_THROTTLE_LATEST_20090511_042308.pkg Inspecting image file types Processing image file constraints Creating candidate provisioning file WARNING: No package of type sipspawmak9 is installed. WARNING: Package will be installed for all SIP slots and bays. Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting list of software package changes --- No old package files removed New files list: Added asr1000rp1sipspawmak9.BLD_V122_33_XND_ASR_RLS4_THROTTLE_LATEST_20090511_042308.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
On each RP in the system, use the request platform software package uninstall command as shown in the following example:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Consolidated Packages and SubPackages Management Managing and Configuring the Router to Run Using Consolidated Packages and Individual SubPackages
Router# request platform software package uninstall rp 0 type sipspawma --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting uninstall preparation --Validating uninstall options Creating candidate provisioning file Finished uninstall preparation --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --- Old files list: Removed asr1000rp1sipspawmak9.BLD_V122_33_XND_ASR_RLS4_THROTTLE_LATEST_20090511_042308.pkg No new package files added Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Step 2 Step 3
Use the show version provisioned command to verify that the optional subpackage is no longer installed. (Optional) Use the request platform software clean command to remove the unused packages.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
The Route Processor (RP) then reloads the chassis and reboots continuously. To troubleshoot this problem, follow these steps:
Step 1 Step 2 Step 3 Step 4
Enable ROM Monitor (ROMmon) mode by entering the reload command. Press the Break key during the first 60 seconds while the system is booting. Force the system to remain in ROMmon mode, waiting for manual bootup, by entering the command: confreg 0x0. Load the latest Cisco IOS XE package or subpackages that are compatible with the ASR1000-ESP10-N ESP board. Compatible subpackages include:
Cisco ASR1000 Series RP1 IP BASE W/O CRYPTO Cisco ASR1000 Series RP1 ADVANCED IP SERVICES W/O CRYPTO Cisco ASR1000 Series RP1 ADVANCED ENTERPRISE SERVICES W/O CRYPTO
Step 5 Step 6
Remove the forced manual boot mode by entering the command: confreg config register setting, where config register setting is the default for the user system, often 0x2102. Reboot the system.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
Caution
Do not run your router using subpackages from different consolidated packages. The Cisco ASR 1000 Series Router is not designed to use multiple subpackages from different consolidated packages. Running subpackages from different consolidated packages is not recommended and can cause unpredictable router behavior. Individual subpackages should only be upgraded individually if you or a Cisco customer support representative has determined that upgrading to the same subpackage that is running could have some benefit for your Cisco ASR 1000 Series Router.
Router# request platform software package install rp 0 file bootflash:asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg slot 1 bay 0 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Finished compatibility testing --- Starting impact testing --Checking operational impact of change
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions interim IPC and database definitions applied Replacing running software Replacing CLI software Restarting software Restarting SPA CC1/0 Applying interim IPC and database definitions Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers
Cisco ASR 1000 Series Aggregation Services Routers support the following software upgrade procedures:
In-Service Software Upgrades (ISSU) for redundant platformsThe ISSU process allows software to be updated or otherwise modified while packet forwarding continues with minimal interruption. ISSU supports two different software upgrade modes:
Consolidated package mode Subpackage mode
The supported platforms include Cisco ASR 1006 and Cisco ASR 1013 Routers.
Upgrade process with service impact for nonredundant platformsNon-hardware-redundant chassis models (such as the Cisco ASR 1001 Router, Cisco ASR 1002 Router and Cisco ASR 1004 Router) do not support ISSU upgrade or downgrade. Instead subpackage software upgrade is supported only if the router is running in subpackage mode.Traffic loss cannot be avoided during the installation of the ESP package as a part of ISSU.
Table 11 lists Compatibility matrix of the software upgrade process for various Cisco ASR 1000 Series Aggregation Services Router.
Table 11 Software Upgrade Compatibility Matrix for Various Cisco ASR 1000 Series Aggregation Services Router Platforms
Platform Cisco ASR 1006 Router CiscoASR 1013 Router CiscoASR 1004 Router CiscoASR 1002 Router CiscoASR 1001 Router
Consolidated Package Supported Supported Not Supported Not Supported Not Supported
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Contents
Your Cisco IOS software release may not support all of the features documented in this module. To reach links to specific feature documentation in this module and to see a list of the releases in which each feature is supported, use the Feature Information for Software Upgrade Process section on page 224.
Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Contents
This guide discusses various software upgrade procedures and contains the following sections:
Prerequisites for Software Upgrade Processes, page 2 ISSU Upgrade for Redundant Platforms, page 2 Upgrade Process With Service Impact for Nonredundant Platforms, page 76 Minimal Disruptive Restart ISSU, page 139
Refer to the ISSU compatibility tables in the Release Notes for Cisco ASR 1000 Series Aggregation Services Routers. 4 GB of DRAM memory is required for installing software upgrade on a system with RP1 route processor. ISSU is supported when the router is running in subpackage mode or in consolidated package mode. For the Cisco ASR 1001 Router, the Cisco IOS Software redundancy requires 8-GB DRAM and the IOS software redundancy license.
Overview of ISSU on the Cisco ASR 1000 Series Routers, page 3 ISSU Upgrade Procedures, page 6 In Service One-Shot Software Upgrade Procedure, page 73 ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2), page 74
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Note
ROMmon images are downloaded separately from Cisco IOS XE images and have their own installation procedures, and are therefore not mentioned as part in this document as part of the ISSU upgrade procedure. Table 11 provides a list of the Cisco ASR 1000 Series Routers subpackages and whether or not they can be upgraded without losing any network traffic in single and dual RP and ESP configurations using ISSU.
Table 12 Limited Interruption Upgrade Compatibility Table
SubPackage Consolidated package (any) RPBase RPControl RPAccess RPIOS ESPBase SIPBase4 SIPSPA5
Nonredundant RP and ESP No (Reload required) No (RP Reload required) Yes (in-service) Yes (in-service) Yes (IOS software switchover) No (ESP reload required)
2 1
Redundant RP and ESP Yes (RP switchover) Yes (RP switchover) Yes (in-service) Yes (in-service) Yes (RP switchover) Yes3 (via ESP switchover)
No (SPAs in SIP do not forward No (SPAs in SIP do not forward traffic during upgrade) traffic during upgrade) No (SPAs in SIP do not forward No (SPAs in SIP do not forward traffic during upgrade) traffic during upgrade)
1. Only supported if software redundancy is configured on the RP. 2. ESP has to reload to complete ESPBase subpackage upgrade. All router traffic will be lost during ESP upgrade.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
3. An ESP switchover occurs as part of the upgrade, so traffic is forwarded with minimal interruption. 4. Any SIPBase upgrade will require the SPA interfaces to go down during the upgrade for all the SPAs in the SIP. 5. Any SIPSPA upgrade will require the SPA interfaces for that particular SPA to go down during the upgrade.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Note
Cisco IOS XE software compatibility is between like images, for example, advipservicesk9 to advipservicesk9, adventerprisek9 to adventerprisek9, and so on. Cross-image-type upgrades or installations are not supported in the ISSU process. For example, you cannot upgrade ipbase to advipservicesk9 or advipservices to advipservicesk9.
Different image types must not be run simultaneously. For ATM SPAs on the Cisco ASR1000 Series Routers, ISSU from releases prior to Cisco IOS XE Release 2.5.0 to Cisco IOS XE Release 2.5.0, or from Cisco IOS XE Release 2.5.0 to a release prior to Cisco IOS XE Release 2.5.0, is not supported. If you want to perform ISSU in this environment, you must first remove the configuration from the ATM SPAs on the router, and then shut down the SPAs using the shutdown command prior to running the ISSU process. Cisco IOS XE releases not listed as compatible in the ISSU compatibility tables (documented in the Release Notes for Cisco ASR 1000 Series Aggregation Services Routers as stated in the Prerequisites for Software Upgrade Processes section on page 2) must not be run simultaneously (in a Cisco ASR1006 series router or Cisco ASR 1013 series router) or co-installed on any of the Cisco ASR1000 Series Routers since unexpected failures of one or both RPs or state loss can be experienced. Cisco IOS XE releases listed as partially compatible may incur a loss of state. Cisco IOS XE releases listed as requiring an intermediate release are not directly compatible; however, a migration path is available to preserve some or all state by upgrading to a separate intermediate version, as shown in the tables. The tables do not cover nonredundant (software or hardware) environments as no incremental update is possible under those circumstances. In Cisco IOS XE Release 3.1S, ISSU upgrade and subpackage software upgrade from Cisco IOS XE Release 2.x.x to Cisco IOS XE Release 3.x.xS, including release 3.1S, are not supported. The ISSU downgrade from Cisco IOS XE Release 3.x.xS, including release 3.1S to 2.x.x, is also not supported.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
ISSU upgrade and subpackage software upgrade is restarted from Cisco IOS XE Release 3.1S. Therefore, rebuilds and releases after Cisco IOS XE Release 3.1S will support ISSU and software upgrade and downgrade, based on the ISSU compatibility matrix tables.
Note
When you run the software upgrade from Cisco IOS XE Release 2.x.x to Cisco IOS XE Release 3.x.xS, you have to load the new image on both RPs, verify that it is good code, change the boot loader variable, and reboot the whole chassis. Failure to do that results in a "wedged" router and the only remedy is physically pull out one of the RPs, boot on the remaining RP, downgrade its code to the same version as the pulled out RP and start the process over again.
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration, page 6 Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration, page 12
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration
Consolidated packages can only be upgraded using ISSU in dual Route Processor configurations. ISSU is not supported for consolidated package upgrades in single Route Processor configurations. If you want the RPs on your Cisco ASR 1000 Series router to be running using a consolidated package after the ISSU upgrade is complete, use the following instructions:
Note
This procedure will only work if the current RPs are already running consolidated packages.
SUMMARY STEPS
1. 2. 3. 4.
ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location copy source-file-system:filename standby-destination-filesystem dir URL-to-target-location dir URL-to-target-stby-location
5. 6. 7. 8. 9.
issu loadversion rp upgrade-rp-number standby-file-system:filename issu runversion telnet ip-address port issu acceptversion issu commitversion
10. show version, show version active-RP running, show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
DETAILED STEPS
Command or Action
Step 1
ip tftp
Purpose Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 2
standby-destination-filesystem
Example:
Router# copy tftp bootflash:
Step 3
source-file-system:filename standby-destination-filesystem
copy
Example:
Router# copy bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33. XNA1.bin stby-bootflash:
Step 4
dir dir
URL-to-target-location URL-to-target-stby-location
Example:
Router# dir bootflash: Router# dir stby-bootflash:
(Optional) Display the contents of the target directories to confirm the successful copy of the file package.
Step 5
Load the target consolidated package onto the standby RP. After you receive the message indicating that the terminal state has been reached, go on to Step 6.
Example:
Router# issu loadversion rp 1 file stby-bootflash:asr1000rp1-adventerprisek9.02.01.01.12 2-33.XNA1.bin
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 6
issu runversion
Example:
Router# issu runversion
If this command is entered before the terminal state is reached, a peer is not online or Standby RP is not in terminal state error message will be seen and the issu runversion command will not work. If the issu runversion command does not run for these reasons, wait for the terminal state is reached message to appear and retry the issu runversion command. You can also monitor the terminal state using the show platform command.
After ISSU runversion is completed, a switchover will automatically occur and the standby RP will become the active RP.
Step 7
telnet ip-address port
Example:
[unix-server-1 ~]$ telnet 172.17.52.157 2003 User Access Verification Username: user Password: ******** Router>
Log in to the RP being upgraded, preferably using the RPs console port, to complete the upgrade. (This is the new active RP, that was the standby RP prior to the ISSU process.)
Note
Ensure the hostname does not end in -stby after logging into the RP, as this indicates that the RP being accessed is still the standby RP.
There are many ways to log on to a console port. The example shows access to the console port from a UNIX host using telnet.
Step 8
issu acceptversion
(Optional) Stops the ISSU rollback timer. This step is optional as long as Step 9 is completed before the rollback timer expires. Completes the ISSU upgrade.
Example:
Router# issu acceptversion
Step 9
issu commitversion
Example:
Router# issu commitversion
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 10
show show show show show version version active-RP running version active-RP provisioned platform running-configuration
Purpose (Optional) Enter the show version, show platform, or show running-configuration commands to confirm that the upgrade completed successfully, as follows:
show versionConfirm that the correct software version is running on your router and that the RP was booted from the correct file. show running-configurationConfirm that the booting configuration, in particular the boot system statements, are correct. Use the show running-config | include boot command to display only the boot statements from the show running-configuration output. show platform Confirm that both RP0 and RP1 are correctly running as active and standby.
Tip
Step 11
hw-module slot RP-slot reload
Example:
Router# hw-module slot R0 reload
Examples
The following example shows how to perform consolidated package upgrade in a dual route processor configuration:
Router(config)# ip tftp source-interface gigabitethernet 0 Router# copy tftp bootflash: Address or name of remote host []? 172.17.16.81 Source filename []? /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]? Accessing tftp://172.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1. bin... Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 329.215 secs (635536 bytes/sec) Router# copy bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin stby-bootflash: Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Copy in progress...CCCCCCCC <output removed for brevity> 209227980 bytes copied in 434.790 secs (481216 bytes/sec) Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Jul 21 2008 15:29:25 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 57604 -rw47071436 May 29 2008 15:45:24 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw5740 May 29 2008 15:45:23 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57605 -rw20334796 May 29 2008 15:45:25 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57606 -rw22294732 May 29 2008 15:45:25 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 57607 -rw21946572 May 29 2008 15:45:26 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57608 -rw48099532 May 29 2008 15:45:27 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57609 -rw34324684 May 29 2008 15:45:28 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg 57610 -rw22124748 May 29 2008 15:45:29 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 14 -rw275093 May 29 2008 16:27:53 -07:00 crashinfo_RP_00_00_20080529-162753-DST 15 -rw7516 Jul 2 2008 15:01:39 -07:00 startup-config 13 -rw45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 16 -rw209227980 Jul 17 2008 16:06:58 -07:00 asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin 928862208 bytes total (76644352 bytes free) Router# dir stby-bootflash: Directory of stby-bootflash:/ 11 drwx 16384 Dec 13 2004 03:45:47 -08:00 lost+found 87937 drwx 4096 Jul 17 2008 16:43:34 -07:00 .rollback_timer 14657 drwx 4096 Jul 17 2008 16:43:34 -07:00 .installer 29313 drwx 4096 Dec 13 2004 03:53:00 -08:00 .ssh 12 -rw33554432 Dec 13 2004 03:53:49 -08:00 nvram_00100 13 -rw208904396 Jun 5 2008 20:12:53 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 58625 drwx 4096 Jul 21 2008 15:32:59 -07:00 .prst_sync 43972 -rw47071436 Jun 5 2008 20:16:55 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 43970 -rw5740 Jun 5 2008 20:16:54 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 43973 -rw20334796 Jun 5 2008 20:16:56 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 43974 -rw22294732 Jun 5 2008 20:16:56 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 43975 -rw21946572 Jun 5 2008 20:16:57 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 43976 -rw48099532 Jun 5 2008 20:16:58 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 43977 -rw34324684 Jun 5 2008 20:16:59 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
43978 -rw22124748 Jun 5 2008 20:17:00 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 43971 -rw6256 Jun 5 2008 20:17:00 -07:00 14 -rw209227980 Jul 17 2008 16:16:07 -07:00 asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin 945377280 bytes total (276652032 bytes free)
packages.conf
Router# issu loadversion rp 1 file stby-bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting system installation readiness checking --Finished system installation readiness checking --- Starting installation changes --Setting up image to boot on next reset Starting automatic rollback timer Finished installation changes SUCCESS: Software will now load. PE23_ASR-1006# *Jul 21 23:34:27.206: %ASR1000_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Jul 21 23:37:05.528: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Jul 21 23:37:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Jul 21 23:37:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Finished installation state synchronization *Jul 21 23:37:26.349: %REDUNDANCY-3-IPC: IOS versions do not match. *Jul 21 23:38:47.172: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Jul 21 23:38:47.173: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# issu runversion --- Starting installation state synchronization --Finished installation state synchronization Initiating active RP failover SUCCESS: Standby RP will now become active PE23_ASR-1006# System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc. <additional output removed for brevity> *Jul 21 23:43:31.970: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Compiled Thu 01-May-08 00:29 by mcpre *Jul 21 23:43:31.978: %SSH-5-ENABLED: SSH 1.99 has been enabled *Jul 21 23:43:35.196: Relay: standby progression done *Jul 21 23:43:35.197: %PLATFORM-6-RF_PROG_SUCCESS: RF state STANDBY HOT
At this point of the procedure, use your UNIX client to log in to the other RP:
[unix-server-1 ~]$ telnet 172.17.52.157 2003 User Access Verification Username: user Password: ******** Router> Router# issu acceptversion Cancelling rollback timer SUCCESS: Rollback timer cancelled Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Saving image changes Finished installation changes Building configuration... [OK] SUCCESS: version committed: bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin
After you confirm the software versions and configuration, reload the RP as shown in the following example:
Router# hw-module slot R0 reload Proceed with reload of module? [confirm] *Jul 21 23:54:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Jul 21 23:54:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Jul 21 23:54:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Jul 21 23:57:05.528: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R0 *Jul 21 23:57:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Jul 21 23:57:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Jul 21 23:58:47.172: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Jul 21 23:58:47.173: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
Using ISSU to Upgrade the SubPackages on a Cisco ASR 1006 or ASR 1013 Router (issu Command Set), page 13 Using ISSU to Upgrade SubPackages on a Cisco ASR 1006 Router or ASR 1013 Router (request platform command set), page 46
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Using ISSU to Upgrade the SubPackages on a Cisco ASR 1006 or ASR 1013 Router (issu Command Set)
This section provides the instructions for performing an ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the issu command set. This procedure can only be performed if the current ASR 1006 or ASR 1013 routers have two active RPs and both RPs are running subpackages.
SUMMARY STEPS
1.
show version show version active-rp installed dir filesystem:<directory> show platform show redundancy-states
2. 3. 4. 5. 6. 7. 8.
copy running-config startup-config mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-standby-RP
9.
10. issu loadversion rp standby-RP file URL-to-standby-file-system:asr1000rp*version*.pkg force 11. hw-module slot standby-RP reload 12. issu loadversion rp active-RP file
URL-to-active-file-system:asr1000rp1-{sipbase,sipspa}*version*.pkg slot SIP-slot-number force issu commitversion Repeat the step 12, for each available SIP installed in the router before moving onto the next step.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
standby-ESP-slot issu commitversion issu loadversion rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot active-ESP-slot issu commitversion
14. issu loadversion rp active-RP file URL-to-active-file-system:asr1000rp1*version*.pkg force 15. show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
DETAILED STEPS
Command or Action
Step 1
show version show version active-rp installed dir filesystem : directory show platform show redundancy states
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed dir bootflash: show platform show redundancy states
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs. show redundancy statesConfirm the operational and configured redundancy states.
Step 2
Example:
Router# copy running-config startup-config
After you have confirmed that the system states are acceptable, save the current configuration to the startup configuration. Create a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Step 3
mkdir
URL-to-directory-name
Example:
Router# mkdir usb0:221subs
Step 4
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 5
copy tftp:
URL-to-target-location
Copy the consolidated package file into the directory created in Step 3. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: usb0:221subs
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 6
request platform software package expand file
Purpose Extract the subpackages out of the consolidated package file into the temporary directory.
Note
URL-to-consolidated-package
Example:
Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.0 1.122-33.XNB1.bin
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 7
dir
target-URL
(Optional) Display the directory to confirm that the files were extracted.
Example:
Router# dir usb0:221subs
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 8
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg bootflash:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 9
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the standby RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-standby-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg stby-bootflash:
Step 10
standby-RP file Upgrade the RP subpackages on the standby RP, where the target-standbyRP-URL-for-sub-packages:asr1000rp* rp* wildcard is specified to capture all of the RP version*.pkg force subpackages for the desired upgrade release.
issu loadversion rp
Example:
Router# issu loadversion rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*. pkg force
Step 11
hw-module slot
standby-RP reload
Example:
Router# hw-module slot R1 reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 12
Purpose Upgrade the SIP and SPA subpackages for each SIP on the router.
Note
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 0 force Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 1 force Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 2 force Router# issu commitversion
Tip
Note
Step 13
active-RP file Upgrade the ESP Base subpackage on the standby and the URL-to-active-file-system:asr1000rp1-esp*version*. active ESPs. pkg slot standby-ESP-slot issu commitversion After entering the issu loadversion rp command on the issu loadversion rp active-RP file active RP, the ESP switchover will occur automatically. URL-to-active-file-system:asr1000rp1-esp*version*. Minimal traffic interruption will occur as a result of this pkg slot active-ESP-slot switchover. issu commitversion
issu loadversion rp
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg slot 1 Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg slot 0 Router# issu commitversion
Step 14
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp1*02.02.01.122-33.XNB1*.pkg force
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Step 15
Example:
Router# show version r0 provisioned Router# show version r0 installed
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 16
redundancy force-switchover
Example:
Router# redundancy force-switchover
Step 17
Example:
Router# request platform software package clean
Examples
The following example shows ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the issu command set
Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) <output removed for brevity> System image file is "bootflash:packages.conf" <output removed for brevity> Router# show platform Chassis type: ASR1006 Slot --------0 0/0 0/1 0/2 0/3 1 1/0 1/1 1/3 R0 R1 F0 F1 P0 P1 Slot --------0 1 R0 R1 F0 F1 Type ------------------ASR1000-SIP10 SPA-4XT-SERIAL SPA-5X1GE-V2 SPA-2XOC3-POS SPA-4XT-SERIAL ASR1000-SIP10 SPA-4X1FE-TX-V2 SPA-2X1GE-V2 SPA-1XOC12-POS ASR1000-RP1 ASR1000-RP1 ASR1000-ESP10 ASR1000-ESP10 ASR1006-PWR-AC ASR1006-FAN CPLD Version ------------------07091401 07091401 07062111 07062111 07091401 07091401 State --------------------ok ok ok ok ok ok ok ok ok ok, active ok, standby ok, active ok, standby ok ok Insert time (ago) ----------------00:03:03 00:01:35 00:01:35 00:01:36 00:01:35 00:03:03 00:01:36 00:01:35 00:01:36 00:03:03 00:03:03 00:03:03 00:03:03 00:02:07 00:02:07
Router# show version r0 installed Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: 174bef13f7ce20af077bae7aaefb5279c790dd57 Package: rpbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: RP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 661bcb2efda479533c87f23504bf7021d42b3165 Package: rpaccess, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg , on: RP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: b0dc8e07cd4f997b045280fa79051e41068c6f3e Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP0/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: RP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 661bcb2efda479533c87f23504bf7021d42b3165 Package: rpaccess, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg , on: RP1 Built: 2008-09-24_03.46, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: b0dc8e07cd4f997b045280fa79051e41068c6f3e Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: espbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: ESP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: da8e5c93d0fa3f7cf27381841fa9efcde409964d Package: espbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: ESP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: da8e5c93d0fa3f7cf27381841fa9efcde409964d Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/0 Built: 2008-09-24_03.46, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/3 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/3 Built: 2008-09-24_03.46, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/3 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Router# mkdir usb0:221subs Create directory filename [221subs]? Created dir bootflash:221subs Router(config)# ip tftp source-interface gigabitethernet 0 Router# copy tftp: usb0:221subs Address or name of remote host []? 172.17.16.81 Source filename []? /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Destination filename [asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin]? Accessing tftp://172.17.16.81//auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin... Loading /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 880.002 secs (237759 bytes/sec) Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir usb0:221subs Directory of usb0:/221subs/ 72013 -rw51904716 Oct 7 2008 15:46:02 -07:00 asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg 72004 -rw5773 Oct 7 2008 15:46:02 -07:00 asr1000rp1-packages-adventerprisek9.02.02.01.122-33.XNB1.conf 72014 -rw20533452 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg 72015 -rw22388940 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg 72016 -rw27961548 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg 72017 -rw50942156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg 72018 -rw36442316 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg 72019 -rw26366156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg 72005 -rw6290 Oct 7 2008 15:46:03 -07:00 packages.conf 72003 -rw224768204 Oct 7 2008 15:38:57 -07:00 asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin 928862208 bytes total (466358272 bytes free) Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
25
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 26366156 bytes copied in 2.857 secs (9228616 bytes/sec)
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
26
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
27
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 26366156 bytes copied in 2.857 secs (9228616 bytes/sec) Router#issu loadversion rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. Router# hw-module slot r1 reload Router# *Sep 25 19:16:29.709: %ASR1000_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Sep 25 19:16:29.787: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) New software will load on reboot.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
28
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
*Sep 25 19:16:29.788: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Sep 25 19:16:29.788: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Sep 25 19:19:05.496: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Sep 25 19:19:30.549: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 19:19:30.550: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Sep 25 19:19:31.512: %REDUNDANCY-3-IPC: IOS versions do not match. *Sep 25 19:21:02.256: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Sep 25 19:21:02.257: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.122-33.XNB1*.pkg slot 0 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
29
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP0 Applying final IPC and database definitions *Sep 29 15:12:18.972: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 0 *Sep 29 15:12:18.973: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled *Sep 29 15:12:18.973: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled *Sep 29 15:12:18.973: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/2, interfaces disabled *Sep 29 15:12:18.973: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/3, interfaces disabled *Sep 29 15:12:18.977: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4XT-SERIAL) offline in subslot 0/0 *Sep 29 15:12:18.981: %SPA_OIR-6-OFFLINECARD: SPA (SPA-5X1GE-V2) offline in subslot 0/1 *Sep 29 15:12:18.985: %SPA_OIR-6-OFFLINECARD: SPA (SPA-2XOC3-POS) offline in subslot 0/2 *Sep 29 15:12:18.994: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4XT-SERIAL) offline in subslot 0/3 *Sep 29 15:13:04.553: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Sep 29 15:13:06.051: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Sep 29 15:13:06.935: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/1 *Sep 29 15:13:07.765: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Sep 29 15:13:08.250: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/3 Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages *Sep 29 15:13:14.936: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up *Sep 29 15:13:21.634: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XT-SERIAL) online in subslot 0/0Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. *Sep 29 15:13:21.967: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/0, changed state to down
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
30
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
*Sep 29 15:13:21.968: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/2, changed state to down *Sep 29 15:13:21.969: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/3, changed state to down *Sep 29 15:13:21.969: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/4, changed state to down *Sep 29 15:13:20.772: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up *Sep 29 15:13:26.364: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XT-SERIAL) online in subslot 0/3 *Sep 29 15:13:25.347: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/0, changed state to down *Sep 29 15:13:25.567: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/2, changed state to down *Sep 29 15:13:26.141: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/3, changed state to down *Sep 29 15:13:26.603: %LINK-3-UPDOWN: SIP0/3: Interface EOBC0/1, changed state to up *Sep 29 15:13:28.355: %LINK-3-UPDOWN: Interface Serial0/3/1, changed state to down *Sep 29 15:13:27.112: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/4, changed state to down Router# Router# Router# Router# Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.122-33.XNB1*.pkg slot 1 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
31
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP1 Applying final IPC and database definitions *Sep 29 15:17:29.883: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 1 *Sep 29 15:17:29.887: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/0, interfaces disabled *Sep 29 15:17:29.887: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/1, interfaces disabled *Sep 29 15:17:29.887: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/3, interfaces disabled *Sep 29 15:17:29.890: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4X1FE-TX-V2) offline in subslot 1/0 *Sep 29 15:17:29.895: %SPA_OIR-6-OFFLINECARD: SPA (SPA-2X1GE-V2) offline in subslot 1/1 *Sep 29 15:17:29.898: %SPA_OIR-6-OFFLINECARD: SPA (SPA-1XOC12-POS) offline in subslot 1/3 *Sep 29 15:18:15.555: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 1 *Sep 29 15:18:16.939: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/0 *Sep 29 15:18:17.721: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/1 *Sep 29 15:18:18.065: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/3 *Sep 29 15:18:24.912: %LINK-3-UPDOWN: SIP1/0: Interface EOBC1/1, changed state to up *Sep 29 15:18:27.856: %SPA_OIR-6-ONLINECARD: SPA (SPA-4X1FE-TX-V2) online in subslot 1/0 Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information *Sep 29 15:18:30.388: %LINK-3-UPDOWN: SIP1/1: Interface EOBC1/1, changed state to upUnmounting old packages *Sep 29 15:18:32.259: %SPA_OIR-6-ONLINECARD: SPA (SPA-2X1GE-V2) online in subslot 1/1 *Sep 29 15:18:33.572: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 1/3Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
32
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
*Sep 29 15:18:34.066: down *Sep 29 15:18:34.281: down *Sep 29 15:18:35.068: GigabitEthernet1/1/0, Router# *Sep 29 15:18:33.905: *Sep 29 15:18:34.625: state to down *Sep 29 15:18:35.293: state to down *Sep 29 15:18:38.950: *Sep 29 15:18:38.686: state to up *Sep 29 15:18:39.972: GigabitEthernet1/1/0,
%LINK-3-UPDOWN: Interface GigabitEthernet1/1/0, changed state to %LINK-3-UPDOWN: Interface GigabitEthernet1/1/1, changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface changed state to down %LINK-3-UPDOWN: SIP1/3: Interface EOBC1/1, changed state to up %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/0, changed %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/1, changed %LINK-3-UPDOWN: Interface GigabitEthernet1/1/0, changed state to up %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/0, changed %LINEPROTO-5-UPDOWN: Line protocol on Interface changed state to up
Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# Router# Router# Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.122-33.XNB1*.pkg slot 2 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
33
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# Router# Router# Router# issu loadversion rp 0 file bootflash:asr1000rp1-espbase*02.02.01.122-33.XNB1*.pkg slot 1 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
34
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
35
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# issu loadversion rp 0 file bootflash:asr1000rp1-espbase.*02.02.01.122-33.XNB1*.pkg slot 0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
36
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP0 Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# issu loadversion rp 0 file bootflash:asr1000rp1*02.02.01.122-33.XNB1*.pkg force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
37
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# show version r0 provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: aca136bd8bcb99f87e6aa7a0ce2a92a3b5a5a200 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
38
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
39
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
40
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown
Router# show version r1 provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: aca136bd8bcb99f87e6aa7a0ce2a92a3b5a5a200 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
41
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
42
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP0/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP0/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
43
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File: unknown, on: SIP2/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Router# redundancy force-switchover Proceed with switchover to standby RP? [confirm] Manual Swact = enabled *Sep 25 19:38:33.562: %SYS-5-SWITCHOVER: Switchover requested by Exec. Reason: redundancy force-switchover Router# request platform software package clean Cleaning up unnecessary package files No path specified, will use booted path bootflash:packages.conf Cleaning bootflash: Scanning boot directory for packages ... done. Preparing packages list to delete ... asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-espbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_ 0100_1.pkg File is in use, will not delete. asr1000rp1-sipbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-sipspa.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. Files that will be deleted: asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.bin asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1 .bin
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
44
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100 _1.conf asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_200809 24_0100_1.conf asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1. pkg asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg packages.conf.00packages.conf.01packages.conf.02packages.conf.03packages.conf.04Do you want to proceed? [confirm]y Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.p kg ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_010 0_1.bin ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080 924_0100_1.bin ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200 80924_0100_1.conf ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LAT EST_20080924_0100_1.conf ... done. Deleting file bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g ... done. Deleting file bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:packages.conf.00- ... done. Deleting file bootflash:packages.conf.01- ... done. Deleting file bootflash:packages.conf.02- ... done. Deleting file bootflash:packages.conf.03- ... done. Deleting file bootflash:packages.conf.04- ... done. SUCCESS: Files deleted.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
45
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Using ISSU to Upgrade SubPackages on a Cisco ASR 1006 Router or ASR 1013 Router (request platform command set)
This procedure can only be performed if the current ASR 1006 router or ASR 1013 router has two active RPs and both RPs are running subpackages. To perform an ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the request platform command set, follow the following instructions.
SUMMARY STEPS
1.
show version show version active-rp installed show version standby-rp installed dir filesystem:<directory> show platform mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-standby-RP request platform software package install rp standby-RP file URL-to-standby-file-system:asr1000rp*version*.pkg force
2. 3. 4. 5. 6. 7.
8.
9.
10. hw-module slot standby-RP reload 11. request platform software package install rp active-RP file URL-to-active-file-system:image slot
SIP-slot-number force Repeat the step 11, for each available SIP installed in the router before moving onto the next step.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
46
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot standby-ESP-slot request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot active-ESP-slot
13. request platform software package install rp active-RP file
URL-to-active-file-system:asr1000rp*version*.pkg force
14. show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
47
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
DETAILED STEPS
Command or Action
Step 1
show version show version active-rp installed show version standby-rp installed dir filesystem :<directory> show platform
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed show version r1 installed dir bootflash: show platform
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs.
Step 2
mkdir
URL-to-directory-name
Creates a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router# mkdir usb0:221subs
Step 3
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 4
copy tftp:
URL-to-target-location
Copies the consolidated package file into the directory created in Step 2. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: usb0:221subs
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
48
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 5
request platform software package expand file
Purpose Extracts the subpackages out of the consolidated package file into the temporary directory.
Note
URL-to-consolidated-package
Example:
Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.0 1.122-33.XNB1.bin
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 6
dir
target-URL
(Optional) Displays the directory to confirm that the files were extracted.
Example:
Router# dir usb0:221subs
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
49
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 7
Purpose Copies the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg bootflash:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
50
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 8
Purpose Copies the subpackages out of the temporary directory into the directory on the router where the subpackages running the standby RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-standby-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg stby-bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg stby-bootflash:
Step 9
request platform software package install rp standby-RP file target-standbyRP-URL-for-sub-packages:asr1000rp* version*.pkg force
Upgrades the RP subpackages on the standby RP, where the rp* wildcard is specified to capture all of the RP subpackages for the desired upgrade release.
Example:
Router# request platform software package install rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*. pkg force
Step 10
hw-module slot
standby-RP reload
Example:
Router# hw-module slot R1 reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
51
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 11
request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-{sipbase,sip spa}*version *.pkg slot SIP-slot-number force Repeat this step for each SIP installed in the router before moving onto the next step.
Purpose Upgrades the SIP and SPA subpackages for each SIP on the router.
Note
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 0 force Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 1 force Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01. 122-33.XNB1*.pkg slot 2 force
Tip
Note
Step 12
request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*. pkg slot standby-ESP-slot
Upgrades the ESP Base subpackage on the standby and the active ESPs.
After entering the issu loadversion rp command on the active RP, the ESP switchover will occur automatically. request platform software package install rp Minimal traffic interruption will occur as a result of this active-RP file URL-to-active-file-system:asr1000rp1-esp*version*. switchover. pkg slot active-ESP-slot
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg slot 1 Router# request platform software package install rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg slot 0
Step 13
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1*02.02.01.122-33.XNB1*.pkg force
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
52
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Command or Action
Step 14
show version show version
Example:
Router# show version r0 provisioned Router# show version r0 installed
Step 15
redundancy force-switchover
Example:
Router# redundancy force-switchover
Step 16
Examples
This example shows ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup:
Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) <output removed for brevity> System image file is "bootflash:packages.conf" <output removed for brevity> Router# show platform Chassis type: ASR1006 Slot --------0 0/0 0/1 0/2 0/3 1 1/0 1/1 1/3 R0 R1 F0 F1 P0 P1 Slot --------0 1 R0 R1 F0 F1 Type ------------------ASR1000-SIP10 SPA-4XT-SERIAL SPA-5X1GE-V2 SPA-2XOC3-POS SPA-4XT-SERIAL ASR1000-SIP10 SPA-4X1FE-TX-V2 SPA-2X1GE-V2 SPA-1XOC12-POS ASR1000-RP1 ASR1000-RP1 ASR1000-ESP10 ASR1000-ESP10 ASR1006-PWR-AC ASR1006-FAN CPLD Version ------------------07091401 07091401 07062111 07062111 07091401 07091401 State --------------------ok ok ok ok ok ok ok ok ok ok, active ok, standby ok, active ok, standby ok ok Insert time (ago) ----------------00:03:03 00:01:35 00:01:35 00:01:36 00:01:35 00:03:03 00:01:36 00:01:35 00:01:36 00:03:03 00:03:03 00:03:03 00:03:03 00:02:07 00:02:07
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
53
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Router# show version r0 installed Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 174bef13f7ce20af077bae7aaefb5279c790dd57 Package: rpbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: RP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 661bcb2efda479533c87f23504bf7021d42b3165 Package: rpaccess, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg , on: RP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: b0dc8e07cd4f997b045280fa79051e41068c6f3e Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP0/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: RP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 661bcb2efda479533c87f23504bf7021d42b3165
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
54
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: rpaccess, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg , on: RP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: b0dc8e07cd4f997b045280fa79051e41068c6f3e Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: rpcontrol, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g, on: RP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 258c79c9b9e67eb4c21dcb4c9b2fe8b8c1f96cfd Package: rpios-adventerprisek9, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 88ea800ae1c094c46ca5e2f26d116f4e0012c219 Package: espbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: ESP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: da8e5c93d0fa3f7cf27381841fa9efcde409964d Package: espbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: ESP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: da8e5c93d0fa3f7cf27381841fa9efcde409964d Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
55
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP0/3 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
56
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP1/3 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipbase, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 31b36be34aa63e0aafbb8abb2cc40a0cbcd5f68e Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/0 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/1 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/2 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Package: sipspa, version: BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg, on: SIP2/3 Built: 2008-09-24_03.46, by: mcpre File SHA1 checksum: 337c662bcea5d34736e6df3acf7d7cb2a0a8c2f7 Router# mkdir usb0:221subs Create directory filename [221subs]? Created dir bootflash:221subs Router(config)# ip tftp source-interface gigabitethernet 0 Router# copy tftp: usb0:221subs Address or name of remote host []? 172.17.16.81 Source filename []? /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Destination filename [asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin]? Accessing tftp://172.17.16.81//auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin... Loading /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
57
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 880.002 secs (237759 bytes/sec) Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir usb0:221subs Directory of usb0:/221subs/ 72013 -rw51904716 Oct 7 2008 15:46:02 -07:00 asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg 72004 -rw5773 Oct 7 2008 15:46:02 -07:00 asr1000rp1-packages-adventerprisek9.02.02.01.122-33.XNB1.conf 72014 -rw20533452 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg 72015 -rw22388940 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg 72016 -rw27961548 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg 72017 -rw50942156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg 72018 -rw36442316 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg 72019 -rw26366156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg 72005 -rw6290 Oct 7 2008 15:46:03 -07:00 packages.conf 72003 -rw224768204 Oct 7 2008 15:38:57 -07:00 asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin 928862208 bytes total (466358272 bytes free) Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
58
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 26366156 bytes copied in 2.857 secs (9228616 bytes/sec)
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
59
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
60
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg stby-bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 26366156 bytes copied in 2.857 secs (9228616 bytes/sec) Router# request platform software package install rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. Router# hw-module slot r1 reload Router# New software will load on reboot.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
61
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
*Sep 25 18:20:15.371: %ASR1000_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Sep 25 18:20:15.426: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Sep 25 18:20:15.427: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Sep 25 18:20:15.427: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Sep 25 18:22:58.808: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Sep 25 18:23:23.038: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 18:23:23.039: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Sep 25 18:23:23.894: %REDUNDANCY-3-IPC: IOS versions do not match. *Sep 25 18:24:54.264: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Sep 25 18:24:54.265: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# Router#request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 0 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
62
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP0 *Sep 29 13:48:03.269: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 0 *Sep 29 13:48:03.270: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled *Sep 29 13:48:03.270: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled *Sep 29 13:48:03.271: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/2, interfaces disabled *Sep 29 13:48:03.271: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/3, interfaces disabled *Sep 29 13:48:03.274: %SPA_OIR-6-OFFLINECARD: Applying final IPC and database definitions SPA (SPA-4XT-SERIAL) offline in subslot 0/0 *Sep 29 13:48:03.278: %SPA_OIR-6-OFFLINECARD: SPA (SPA-5X1GE-V2) offline in subslot 0/1 *Sep 29 13:48:03.282: %SPA_OIR-6-OFFLINECARD: SPA (SPA-2XOC3-POS) offline in subslot 0/2 *Sep 29 13:48:03.286: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4XT-SERIAL) offline in subslot 0/3 *Sep 29 13:48:49.448: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Sep 29 13:48:50.872: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Sep 29 13:48:51.703: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/1 *Sep 29 13:48:52.680: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Sep 29 13:48:53.217: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/3 Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information *Sep 29 13:49:01.336: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XT-SERIAL) online in subslot 0/0 *Sep 29 13:49:03.344: %LINK-3-UPDOWN: Interface Serial0/0/2, changed state to downUnmounting old packages *Sep 29 13:48:59.734: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to upCleaning temporary installation files
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
63
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Finished update running software SUCCESS: Finished installing software. Router# *Sep 29 13:49:05.151: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up *Sep 29 13:49:08.006: %SPA_OIR-6-ONLINECARD: SPA (SPA-5X1GE-V2) online in subslot 0/1 *Sep 29 13:49:09.086: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/2, changed state to down *Sep 29 13:49:09.087: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/3, changed state to down *Sep 29 13:49:09.087: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/4, changed state to down *Sep 29 13:49:09.294: %SPA_OIR-6-ONLINECARD: SPA (SPA-2XOC3-POS) online in subslot 0/2 *Sep 29 13:49:09.580: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/0, changed state to down *Sep 29 13:49:07.951: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up *Sep 29 13:49:11.289: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XT-SERIAL) online in subslot 0/3 *Sep 29 13:49:10.788: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/0, changed state to down *Sep 29 13:49:11.114: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/2, changed state to down *Sep 29 13:49:11.217: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/3, changed state to down *Sep 29 13:49:11.530: %LINK-3-UPDOWN: SIP0/1: Interface GigabitEthernet0/1/4, changed state to down *Sep 29 13:49:10.567: %LINK-3-UPDOWN: SIP0/3: Interface EOBC0/1, changed state to up *Sep 29 13:49:13.289: %LINK-3-UPDOWN: Interface Serial0/3/1, changed state to down Router# Router# Router#request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 1 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
64
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP1 Applying final IPC and database definitions *Sep 29 13:53:01.370: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 1 *Sep 29 13:53:01.370: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/0, interfaces disabled *Sep 29 13:53:01.370: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/1, interfaces disabled *Sep 29 13:53:01.370: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/3, interfaces disabled *Sep 29 13:53:01.373: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4X1FE-TX-V2) offline in subslot 1/0 *Sep 29 13:53:01.378: %SPA_OIR-6-OFFLINECARD: SPA (SPA-2X1GE-V2) offline in subslot 1/1 *Sep 29 13:53:01.381: %SPA_OIR-6-OFFLINECARD: SPA (SPA-1XOC12-POS) offline in subslot 1/3 *Sep 29 13:53:45.225: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 1 *Sep 29 13:53:47.082: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/0 *Sep 29 13:53:47.833: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/1 *Sep 29 13:53:48.727: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/3 Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information *Sep 29 13:53:55.700: %LINK-3-UPDOWN: SIP1/0: Interface EOBC1/1, changed state to upUnmounting old packages *Sep 29 13:54:03.132: down *Sep 29 13:54:03.135: down *Sep 29 13:54:00.621: *Sep 29 13:54:03.449: *Sep 29 13:54:04.139: GigabitEthernet1/1/0, %LINK-3-UPDOWN: Interface GigabitEthernet1/1/0, changed state to %LINK-3-UPDOWN: Interface GigabitEthernet1/1/1, changed state to %LINK-3-UPDOWN: SIP1/1: Interface EOBC1/1, changed state to up %SPA_OIR-6-ONLINECARD: SPA (SPA-2X1GE-V2) online in subslot 1/1 %LINEPROTO-5-UPDOWN: Line protocol on Interface changed state to downCleaning temporary installation files
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
65
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Finished update running software SUCCESS: Finished installing software. *Sep 29 13:54:04.320: %SPA_OIR-6-ONLINECARD: SPA (SPA-4X1FE-TX-V2) online in subslot 1/0 Router# *Sep 29 13:54:05.911: %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/0, changed state to down *Sep 29 13:54:06.243: %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/1, changed state to down *Sep 29 13:54:03.492: %LINK-3-UPDOWN: SIP1/3: Interface EOBC1/1, changed state to up *Sep 29 13:54:09.434: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 1/3 *Sep 29 13:54:10.427: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/0, changed state to up *Sep 29 13:54:09.709: %LINK-3-UPDOWN: SIP1/1: Interface GigabitEthernet1/1/0, changed state to up *Sep 29 13:54:11.445: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/0, changed state to up Router# Router# Router# Router# Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 2 force --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
66
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# Router# request platform software package install rp 0 file bootflash:asr1000rp1-espbase*02.02.01.122-33.XNB1*.pkg slot 1 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
67
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP1 Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# request platform software package install rp 0 file bootflash:asr1000rp1-espbase.*02.02.01.122-33.XNB1*.pkg slot 0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
68
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP0 Applying final IPC and database definitions Generating software version information
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
69
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Router# request platform software package install rp 0 file bootflash:asr1000rp1*02.02.01.122-33.XNB1*.pkg --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# show version r0 provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
70
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: aca136bd8bcb99f87e6aa7a0ce2a92a3b5a5a200 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
71
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
72
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP1/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
73
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
The one-shot upgrade procedure is divided into stages. When a failure occurs, the command execution is stalled and users have to perform the rollback tasks manually. Necessary switchovers are automatically taken care of in one of the upgrade stages. During a switchover, the console and its output are lost. Additional commands are used to connect back to the console.
Note
One-shot upgrade does not support multiple upgrades at the same time. The command request platform software package install node file <consolidated file name> interface-module-delay <secs> is used for the one-shot ISSU procedure. interface-module-delay is an optional parameter. Example:
router#request platform software package install node file bootflash interface-module-delay 1
The SIP-delay option enables you to delay the SIP restart duration thus enabling you to choose the restart time to minimize traffic loss. The request platform software package install node attach command enables the users to view the last run log that contains the reports of all the stages of the one-shot upgrade. The request platform software package install file mdr command enables the users to initiate the ISSU procedure using MDR. For more information see, Minimal Disruptive Restart ISSU section on page 139.
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2), page 74 Using ISSU to Upgrade SubPackages (Prior to Cisco IOS XE Release 2.1.2), page 74
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration (Prior to Cisco IOS XE 2.1.2)
This procedure is identical to the procedure used to upgrade post-Cisco IOS XE 2.2 images using ISSU. See the Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration section on page 6 for instructions on performing this process.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
74
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers ISSU Upgrade for Redundant Platforms
Step 1 Step 2
Copy all subpackages other than the RPBase subpackage into the same directory. Install the RP subpackages from the directory simultaneously by using a wildcard statement to capture all of the RP subpackages. This command should capture the RPControl, RPAccess, and RPIOS subpackages without capturing the RPBase subpackage and should be done using the standby bay. Use the asr1000rp1-rp*version.pkg syntax instead of using the {pattern} syntax to complete this upgrade: request platform software package install rp 1 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg bay 1 force
Wait for the system to reach SSO ready state. The show platform command can be used to monitor whether both IOS instances are active, and a system message will indicate SSO state has been reached. Use the redundancy force-switchover command to trigger an IOS switchover. Wait for the system to reach SSO ready state. Like in step 3, the state can be monitored by checking system messages or by entering the show platform command. Install the RP subpackages from the directory simultaneously by using a wildcard statement to capture all of the RP subpackages. This command should capture the RPControl, RPAccess, and RPIOS subpackages without capturing the RPBase subpackage and should be done using the standby bay. Use the asr1000rp1-rp*version.pkg syntax instead of using the {pattern} syntax to complete this upgrade:
request platform software package install rp 0 file stby-bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg bay 0 force
Step 7
Step 8
Step 9
Copy the RPBase subpackage into the directory, then upgrade all of the RP subpackages simultaneously. This step will upgrade the RPBase subpackage, which is the last remaining subpackage that requires an upgrade:
request platform software package install rp 1 file bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg force
Step 10 Step 11
Enter show version provisioned to confirm that all of the software has been updated. Reload the router using the reload command when appropriate to complete the installation.
Downgrades in versions that do not support the {pattern} syntax are problematic because an RPBASE package for the downgrade version will always be present if an upgrade was previously performed. Removing and restaging all packages will work in this case, but they effectively put the system into a state where if the RP reloads prior to the installation being completed, the RP may no longer be bootable.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
75
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Note
The Cisco ASR 1002 and ASR 1002-F Routers come by default with 4-GB DRAM. The Cisco ASR 1001 Router comes by default with 4-GB DRAM, and is upgradeable up to 8-GB or 16-GB DRAM. This section explains how to upgrade subpackages on a Cisco ASR 1001, 1002 or 1004 Router. It contains the following sections:
Configuring SSO on a Cisco ASR 1001, Cisco ASR 1002, or Cisco ASR 1004 Router, page 76 Using SubPackages for Software Upgrade on a Cisco ASR 1001 Router, page 78 Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (software upgrade Command Set), page 93 Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (request platform Command Set), page 118
Configuring SSO on a Cisco ASR 1001, Cisco ASR 1002, or Cisco ASR 1004 Router
The following instructions show how to configure SSO on a Cisco ASR 1001, Cisco ASR 1002, and Cisco ASR 1004 Routers. The standby IOS process is created automatically as part of these configuration steps.
Step 1
(Optional) Enter the show version command to confirm the amount of DRAM on your router:
Router# show version <some output removed for brevity> 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at bootflash:. Configuration register is 0x2102
In the example show version output, the router has 4 GB of DRAM memory. If you are using a Cisco ASR 1001, Cisco ASR 1002, or Cisco ASR 1004 Router with 2-GB DRAM memory on the RP, SSO cannot be configured on your RP.
Step 2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
76
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Router# show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit ID = 6 Redundancy Mode (Operational) = Non-redundant Redundancy Mode (Configured) = Non-redundant Redundancy State = Non Redundant
In this example, HA for the dual RPs is not configured, as indicated by the nonredundant operational mode.
Step 3
Step 4
Step 5
Enter mode sso to enable SSO, or mode none to disable dual software redundancy:
Router(config-red)# mode sso Router(config-red)# mode none
Step 6
Return to privileged EXEC mode using any method, such as entering Ctrl-Z or the exit command multiple times until you get to the # router prompt:
Router(config-red)#^Z Router# Router(config-red)#exit Router(config)#exit Router#
Step 7
Enter the show redundancy states command to confirm the configured redundancy mode changed to your new configuration. In the following example, the configured redundancy mode has been changed to SSO. Note that the operation redundancy mode remains unchanged:
Router# show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit ID = 6 Redundancy Mode (Operational) = Non-redundant Redundancy Mode (Configured) = sso Redundancy State = Non Redundant
Step 8
Enter the copy running-config startup-config command to save the new configuration, and press enter to confirm the filename (or change the name, if desired):
Router# copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] PE25_ASR-1004#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
77
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Step 9
After the reload is complete, enter the show redundancy states command to confirm the operational redundancy mode has changed to the mode that you configured in Step 5. In this example, the operational redundancy mode has changed to SSO:
Router# show redundancy states my state = 13 -ACTIVE peer state = 8 -STANDBY HOT Mode = Duplex Unit ID = 6 Redundancy Mode (Operational) = sso Redundancy Mode (Configured) = sso Redundancy State = sso
Step 10
The router must be reloaded for the new HA configuration. Enter the reload command to reload the router:
Router# reload Proceed with reload? [confirm] <bootup messages removed for brevity>
If you are not using the console port to complete this procedure, your session may be terminated at this point. If you session is terminated, give the router a few minutes to complete the reload and then log into the router.
Step 11
(Optional) To confirm an active and a standby IOS process exist, and how the processes are numbered, enter the show platform command. In this example, the show platform command output reveals that R0/0 is the active IOS process and R0/1 is the standby IOS process:
Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 R0 R0/0 R0/1 F0 P0 P1 Type ------------------ASR1000-SIP10 SPA-2X1GE-V2 SPA-2XT3/E3 ASR1000-RP1 State --------------------ok ok ok ok ok, active ok, standby ok, active ok ok Insert time (ago) ----------------00:52:34 00:51:30 00:51:24 00:52:34 00:52:34 00:51:00 00:52:34 00:51:57 00:51:57
SUMMARY STEPS
1.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
78
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
3. 4. 5. 6. 7. 8.
mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1001-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP issu loadversion rp 0 file file-system:asr1001-{rpaccess,rpios,rpcontrol}*version-string*.pkg bay standby-bay force
9.
10. issu commitversion 11. redundancy force-switchover 12. show platform 13. issu loadversion rp 0 file file-system:asr1001-{rpaccess,rpios,rpcontrol}*version-string*.pkg
force
16. show version installed 17. reload
Note
Step 17 does not have to be performed immediately, and should be done at a convenient time.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
79
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
DETAILED STEPS
Command or Action
Step 1
show version show version installed dir filesystem:<directory> show platform show redundancy-states
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed dir bootflash: show platform show redundancy-states
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs. show redundancy statesConfirm the operational and configured redundancy states. Save the configuration after making this configuration step.
Step 2
Example:
Router(config)# redundancy Router(config-red)# mode sso
Step 3
mkdir URL-to-directory-name
Create a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router# mkdir 221subs
Step 4
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 5
Copy the consolidated package file into the directory created in Step 3. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: 221subs
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
80
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 6
request platform software package expand file URL-to-consolidated-package (Optional) dir target-URL
Purpose Extract the subpackages out of the consolidated package file into the temporary directory.
Note
Example:
Router# request platform software package expand file usb0:221subs/asr1001-universalk9.03.02.01.S.151-1.S 1_2.bin Router# dir 221subs
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 7
dir
target-URL
(Optional) Display the directory to confirm that the files were extracted.
Example:
Router# dir 221subs
Step 8
copy file-system:asr1001-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1001-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP
Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
Example:
Router# copy 221subs/asr1001-espbase.03.02.01.S.151-1.S1_2.pkg bootflash: Router# copy 221subs/asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg bootflash: Router# copy 221subs/asr1001-rpbase.03.02.01.S.151-1.S1_2.pkg bootflash: Router# copy 221subs/asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg bootflash: Router# copy 221subs/asr1001-rpios-universalk9.03.02.01.S.151-1. S1_2.pkg bootflash: Router# copy 221subs/asr1001-sipbase.03.02.01.S.151-1.S1_2.pkg bootflash: Router# copy 221subs/asr1001-sipspa.03.02.01.S.151-1.S1_2.pkg bootflash:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
81
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 9
issu loadversion rp 0 file
Purpose Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay.
Example:
Router# issu commitversion
Force a switchover from the active IOS process to the standby IOS process.
Note
Example:
Router# redundancy force-switchover
Your connection to the router often drops and is expected behavior at this point of the procedure in many scenarios. If this step drops your connection to the router, wait a few minutes before reconnecting to the router and then continue to Step 12.
(Optional) Monitor system state to ensure both IOS processes are active.
Example:
Router# show platform
Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay (a different bay than in Step 9).
Example:
Router# issu loadversion rp 0 file bootflash:asr1001-{rpaccess,rpios,rpcontrol}*03.02. 01.S.151-1.S1_2*.pkg bay 0 force
Example:
Router# issu commitversion
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
82
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 15 issu loadversion rp 0 file
Purpose
Upgrade the RP, SIP, SPA, and ESP subpackages for file-system:asr1001-{rpbase,sipbase,sipspa,espbase}*v each SIP on the router. ersion*.pkg force Note This step must be completed one SIP at a time, and repeated for each SIP installed on the router Example: before performing the next step. Router#issu loadversion rp 0 file
bootflash:221subs/asr1001-{rpbase,sipbase,sipspa,es pbase}*03.02.01.S.151-1.S1_2.pkg force
Tip
You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (rpbase, sipbase, sipspa, and espbase) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Note
Example:
Router# show version installed
Step 17 reload
Example:
Router# reload
The router will continue normal operation even without a reload, so you can reload the router during scheduled maintenance or a slower traffic period. It is highly recommended reload to avoid conflicts in the software base.
Examples
The following example shows the software upgrade for Cisco ASR 1001 Router running subpackages.
Router#show version Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Experimental Version 15.1(20110301:124851) [asr1001-universalk9.03.02.01.S.151-1.S1] Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Tue 01-Mar-11 06:25 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2011 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
83
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
ROM: IOS-XE ROMMON Router uptime is 5 days, 26 minutes Uptime for this control processor is 5 days, 27 minutes System returned to ROM by reload System image file is "bootflash:asr1001-universalk9.03.02.01.S.151-1.S1" Last reload reason: Reload Command
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com.
License Info: License UDI: Device# PID SN UDI -------------------------------------------------------------------------------*0 ASR1001 JAE14020AT1 ASR1001:JAE14020AT1
License Package Information for Module:'asr1001' Module name Image level Pri Config Valid license -----------------------------------------------------------------------asr1001 adventerprise 1 NO adventerprise advipservices 2 NO advipservices ipbase 3 NO ipbase Module name Current Level Reboot Level -----------------------------------------------------------------------asr1001 ipbase ipbase cisco ASR1001 (1RU) processor with 3851680K/6147K bytes of memory. 6 Gigabit Ethernet interfaces 32768K bytes of non-volatile configuration memory. 8388608K bytes of physical memory. 7782399K bytes of eUSB flash at bootflash:. Configuration register is 0x8102 Router# show version installed Package: Provisioning File, version: n/a, status: active File: consolidated:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: e11c9aacb8c233ed10eeac61ca20a9469fb0b81e Package: rpbase, version: 03.02.01.S.151-1.S1, status: active File: consolidated:asr1001-rpbase.03.02.01.S.151-1.S1.pkg, on: RP0 Built: 2011-03-01_07.10, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
84
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
File SHA1 checksum: e3c93ac457f2632ae90ba346692d58001cf0d02c Package: rpcontrol, version: 03.02.01.S.151-1.S1, status: active File: consolidated:asr1001-rpcontrol.03.02.01.S.151-1.S1.pkg, on: RP0/0 Built: 2011-03-01_07.10, by: mcpre File SHA1 checksum: 59ba43488cf2a0e7bc06b66fad0e574bbdf42a62 <output removed for brevity>
Router#show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit = Primary Unit ID = 48 Redundancy Mode (Operational) = Non-redundant Redundancy Mode (Configured) = Non-redundant Redundancy State = Non Redundant Manual Swact = disabled (system is simplex (no peer unit)) Communications = Down Reason: Simplex mode client count = 63 client_notification_TMR keep_alive TMR keep_alive count keep_alive threshold RF debug mask Router# show platform Chassis type: ASR1001 Slot --------0 0/0 0/1 R0 F0 P0 P1 P2 Slot --------0 R0 F0 Type ------------------ASR1001 ASR1001 SPA-2X1GE-V2 ASR1001 ASR1001 ASR1001-PWR-AC ASR1001-PWR-AC ASR1001-FANTRAY CPLD Version ------------------1001050E 10010514 1001050E State --------------------ok ok ok ok, active ok, active ps, fail ok ok Insert time (ago) ----------------5d07h 5d07h 5d07h 5d07h 5d07h 5d07h 5d07h 5d07h
= = = = =
Router# mkdir 221subs Create directory filename [221subs]? Created dir bootflash:221subs Router(config)# ip tftp source-interface gigabitethernet 0 Router# copy tftp: 221subs Address or name of remote host []? 172.27.55.254 Source filename []? /auto/users/asr1001-universalk9.03.02.01.S.151-1.S1_2.bin,12 Destination filename [asr1001-universalk9.03.02.01.S.151-1.S1.bin,12]? Accessing tftp://172.27.55.254//auto/users/asr1001-universalk9.03.02.01.S.151-1.S1_2.bin,12... Loading /auto/users/asr1001-universalk9.03.02.01.S.151-1.S1.bin,12 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
85
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 880.002 secs (237759 bytes/sec) Router# request platform software package expand file 221subs/asr1001-universalk9.03.02.01.S.151-1.S1_2.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir 221subs Directory of 221subs/ 72013 -rw51904716 Oct 7 2008 15:46:02 -07:00 asr1001-espbase.03.02.01.S.151-1.S1_2.pkg 72004 -rw5773 Oct 7 2008 15:46:02 -07:00 asr1001-packages-universalk9.03.02.01.S.151-1.S1_2.conf 72014 -rw20533452 Oct 7 2008 15:46:03 -07:00 asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg 72015 -rw22388940 Oct 7 2008 15:46:03 -07:00 asr1001-rpbase.03.02.01.S.151-1.S1_2.pkg 72016 -rw27961548 Oct 7 2008 15:46:03 -07:00 asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg 72017 -rw50942156 Oct 7 2008 15:46:03 -07:00 asr1001-rpios-universalk9.03.02.01.S.151-1.S1_2.pkg 72018 -rw36442316 Oct 7 2008 15:46:03 -07:00 asr1001-sipbase.03.02.01.S.151-1.S1_2.pkg 72019 -rw26366156 Oct 7 2008 15:46:03 -07:00 asr1001-sipspa.03.02.01.S.151-1.S1_2.pkg 72005 -rw6290 Oct 7 2008 15:46:03 -07:00 packages.conf 72003 -rw224768204 Oct 7 2008 15:38:57 -07:00 asr1001-universalk9.03.02.01.S.151-1.S1_2.bin 928862208 bytes total (466358272 bytes free) Router# copy 221subs/asr1001-espbase.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-espbase.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy 221subs/asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
86
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy 221subs/asr1001-rpbase.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-rpbase.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy 221subs/asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy 221subs/asr1001-rpios-universalk9.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-rpios-universalk9.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy 221subs/asr1001-sipbase.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-sipbase.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy 221subs/asr1001-sipspa.03.02.01.S.151-1.S1_2.pkg bootflash: Destination filename [asr1001-sipspa.03.02.01.S.151-1.S1_2.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
87
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
--- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg Found asr1001-rpios-universalk9.03.02.01.S.151-1.S1_2.pkg Found asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting list of software package changes --No old package files removed New files list: Added asr1001-rpaccess.03.02.01.S.151-1.S1_2.pkg Added asr1001-rpcontrol.03.02.01.S.151-1.S1_2.pkg Added asr1001-rpios-universalk9.03.02.01.S.151-1.S1_2.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
88
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting IOS PID: 9275, in slot/bay 0/1 *Mar 15 16:28:50.014: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 15 16:28:50.014: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Mar 15 16:28:50.014: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 15 16:28:52.224: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 15 16:29:29.214: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 15 16:29:29.214: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Generating software version information Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software
Router#issu commitversion --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation Router# *Mar 15 16:30:24.885: *Mar 15 16:30:25.421: *Mar 15 16:30:25.423: changes committed %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeedd %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
%ASR1000_INFRA-6-CONSOLE_ACTIVE: R0/1 console active. *Mar *Mar *Mar *Mar 15 15 15 15 16:31:00.014: 16:31:00.015: 16:31:00.015: 16:31:00.328: %REDUNDANCY-3-SWITCHOVER: %REDUNDANCY-3-SWITCHOVER: %REDUNDANCY-3-SWITCHOVER: %LINK-3-UPDOWN: Interface
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
89
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
*Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar *Mar
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
16:31:00.328: 16:31:00.328: 16:31:01.328: 16:31:01.328: 16:31:01.328: 16:31:01.328: 16:31:02.064: 16:31:02.293: 16:31:02.321: 16:31:03.321: 16:31:03.322: 16:31:03.322: 16:31:03.322: 16:31:03.322: 16:31:03.322: 16:31:03.322: 16:31:43.189: 16:31:43.189: 16:32:28.411: 16:32:28.971: 16:32:28.973:
%LINK-3-UPDOWN: Interface EOBC0, changed state to up %LINK-3-UPDOWN: Interface LIIN0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, cp %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, chp %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, chp %RF-5-RF_RELOAD: Self reload. Reason: redundancy force-swr %SYS-5-SWITCHOVER: Switchover requested by red_switchover. %LINK-3-UPDOWN: Interface Null0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Null0, chp %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEtn %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a stand) %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a stand) %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeedd %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
Router# issu loadversion rp 0 file bootflash:221subs/asr1001-{rpaccess,rpios,rpcontrol}*03.02.01.S.151-1.S1_2.pkg bay 0 force --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
90
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Finished compatibility testing --- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting list of software package changes --Old files list: Removed asr1001-rpaccess.03.02.01.S.151-1.S1.pkg Removed asr1001-rpcontrol.03.02.01.S.151-1.S1.pkg Removed asr1001-rpios-universalk9.03.02.01.S.151-1.S1.pkg No new package files added Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting IOS PID: 20548, in slot/bay 0/0 *Mar 15 16:36:14.365: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 15 16:36:14.365: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Mar 15 16:36:14.365: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 15 16:36:16.558: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 15 16:36:49.365: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 15 16:36:49.365: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Router#issu commitversion --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation changes --Cancelling rollback timer
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
91
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Router#issu loadversion rp 0 file bootflash:221subs/asr1001-{rpbase,sipbase,sipspa,espbase}*03.02.01.S.151-1.S1_2.pkg force --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Verifying image file locations Inspecting image file types WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP WARNING: Automatically setting the on-reboot flag Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --Old files list: Removed asr1001-espbase.03.02.01.S.151-1.S1.pkg Removed asr1001-rpbase.03.02.01.S.151-1.S1.pkg Removed asr1001-sipbase.03.02.01.S.151-1.S1.pkg Removed asr1001-sipspa.03.02.01.S.151-1.S1.pkg New files list: Added asr1001-espbase.03.02.01.S.151-1.S1_2.pkg Added asr1001-rpbase.03.02.01.S.151-1.S1_2.pkg Added asr1001-sipbase.03.02.01.S.151-1.S1_2.pkg Added asr1001-sipspa.03.02.01.S.151-1.S1_2.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
92
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (software upgrade Command Set)
This section provides instructions on using software upgrade for Cisco ASR 1002 or 1004 Router running subpackages. These instructions assume two IOS processes are active on the RP and that the router is already running using subpackages. For information on checking and configuring two IOS processes on the same RP, see the Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (software upgrade Command Set) section on page 93.
SUMMARY STEPS
1.
show version show version installed dir filesystem:<directory> show platform show redundancy-states
2.
3. 4. 5. 6. 7. 8.
mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP issu loadversion rp 0 file file-system:asr1000rp1-{rpaccess,rpios,rpcontrol}*version-string*.pkg bay standby-bay force
9.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
93
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
SIP-slot-number force issu commitversion Repeat the step 15, for each available SIP installed in the router before moving onto the next step.
16. issu loadversion rp 0 file file-system:asr1000rp1-esp*version*.pkg force 17. issu commitversion 18. issu loadversion rp 0 file file-system:asr1000rp*version*.pkg 19. show version installed 20. reload 21. request platform software package clean
Note
Step 19, 20, and 21 does not have to be performed immediately, and can be done at a convenient time.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
94
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
DETAILED STEPS
Command or Action
Step 1
show version show version installed dir filesystem:<directory> show platform show redundancy-states
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed dir bootflash: show platform show redundancy-states
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs. show redundancy statesConfirm the operational and configured redundancy states. Save the configuration after making this configuration step.
Step 2
Example:
Router(config)# redundancy Router(config-red)# mode sso
Step 3
mkdir URL-to-directory-name
Create a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router# mkdir usb0:221subs
Step 4
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 5
copy tftp:
URL-to-target-location
Copy the consolidated package file into the directory created in Step 3. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: usb0:221subs
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
95
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 6
request platform software package expand file URL-to-consolidated-package (Optional) dir target-URL
Purpose Extract the subpackages out of the consolidated package file into the temporary directory.
Note
Example:
Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.0 1.122-33.XNB1.bin Router# dir usb0:221subs
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 7
dir target-URL
(Optional) Display the directory to confirm that the files were extracted.
Example:
Router# dir usb0:221subs
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
96
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 8
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg bootflash:
Step 9
Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay.
Step 10
issu commitversion
Example:
Router# issu commitversion
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
97
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 11
redundancy force-switchover
Purpose Force a switchover from the active IOS process to the standby IOS process.
Note
Example:
Router# redundancy force-switchover
Your connection to the router often drops and is expected behavior at this point of the procedure in many scenarios. If this step drops your connection to the router, wait a few minutes before reconnecting to the router and then continue to Step 12.
Step 12
show platform
(Optional) Monitor system state to ensure both IOS processes are active.
Example:
Router# show platform
Step 13
Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay (a different bay than in Step 9).
Step 14
issu commitversion
Example:
Router# issu commitversion
Step 15
issu loadversion rp 0 file file-system:asr1000rp1-{sipbase,sipspa}*version*. pkg slot SIP-slot-number force issu commitversion Repeat this step for each SIP installed in your router before proceeding to the next step.
Upgrade the SIP and SPA subpackages for each SIP on the router.
Note
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 0 force Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 1 force Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 2 force Router# issu commitversion
Tip
Note
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
98
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 16
issu loadversion rp 0 file file-system:asr1000rp1-esp*version*.pkg force
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg force
Step 17
issu commitversion
Example:
Router# issu commitversion
Step 18
file-system:asr1000rp*version*.pkg
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg
Upgrades all subpackages, including the RPBase subpackage, which is the last subpackage that needs to be upgraded.
Note
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Step 19
Example:
Router# show version installed
Step 20
reload
Example:
Router# reload
The router will continue normal operation even without a reload, so you can reload the router during scheduled maintenance or a slower traffic period.
Step 21
Examples
The following example shows the software upgrade for Cisco ASR 1002 or 1004 Router running sub-packages:
Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) <output removed for brevity> System image file is "bootflash:packages.conf" <output removed for brevity> cisco ASR1004 (RP1) processor with 752142K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 2 Serial interfaces 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 937983K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at bootflash:. 253424K bytes of USB flash at usb0:.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
99
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Configuration register is 0x2102 Router# show version installed Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 9172d30751d79fc1afb7b405eca244bbf9f8f2f2 Package: rpbase, version: 02.01.00.122-33.XNA, status: active File: bootflash:asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg, on: RP0 Built: 2008-05-01_01.48, by: mcpre File SHA1 checksum: c09fe08ff908c8ce0b789d8acc774fe43dacf5e3 Package: rpaccess, version: 02.01.01.122-33.XNA, status: active File: bootflash:asr1000rp1-rpaccess.02.01.01.122-33.XNA.pkg, on: RP0 Built: 2008-07-08_16.01, by: mcpre File SHA1 checksum: c1afc591c9cd198409820226c4f23d2647d0d138 <output removed for brevity>
Router# show redundancy states my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit ID = 48 Redundancy Mode (Operational) = sso Redundancy Mode (Configured) = sso Redundancy State = sso Maintenance Mode = Disabled Manual Swact = disabled (peer unit not yet in terminal standby state) Communications = Up client count = 67 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0 Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 0/3 R0 R0/0 R0/1 F0 P0 P1 Slot --------0 R0 F0 Type ------------------ASR1000-SIP10 SPA-1XOC12-POS SPA-2XOC3-POS SPA-5X1GE-V2 ASR1000-RP1 State --------------------ok ok ok ok ok ok, active ok, standby ok, active ok ok Insert time (ago) ----------------00:04:43 00:03:25 00:03:24 00:03:20 00:04:43 00:04:43 00:02:55 00:04:43 00:03:53 00:03:53
Router# mkdir usb0:221subs Create directory filename [221subs]? Created dir bootflash:221subs Router(config)# ip tftp source-interface gigabitethernet 0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
100
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Router# copy tftp: usb0:221subs Address or name of remote host []? 172.17.16.81 Source filename []? /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Destination filename [asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin]? Accessing tftp://172.17.16.81//auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin... Loading /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 880.002 secs (237759 bytes/sec) Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir usb0:221subs Directory of usb0:/221subs/ 72013 -rw51904716 Oct 7 2008 15:46:02 -07:00 asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg 72004 -rw5773 Oct 7 2008 15:46:02 -07:00 asr1000rp1-packages-adventerprisek9.02.02.01.122-33.XNB1.conf 72014 -rw20533452 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg 72015 -rw22388940 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg 72016 -rw27961548 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg 72017 -rw50942156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg 72018 -rw36442316 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg 72019 -rw26366156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg 72005 -rw6290 Oct 7 2008 15:46:03 -07:00 packages.conf 72003 -rw224768204 Oct 7 2008 15:38:57 -07:00 asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin 928862208 bytes total (466358272 bytes free) Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
101
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
102
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
103
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software *Sep 25 18:04:39.462: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Sep 25 18:04:39.462: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Sep 25 18:04:39.463: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Sep 25 18:05:32.476: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 18:05:32.476: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Router# *Sep 25 18:05:33.409: %REDUNDANCY-3-IPC: IOS versions do not match. *Sep 25 18:07:39.886: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded Router# *Sep 25 18:07:39.888: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# redundancy force-switchover Proceed with switchover to standby RP? [confirm] %ASR1000_INFRA-6-CONSOLE_ACTIVE: R0/1 console active. Press RETURN to get started!
*Sep 25 18:08:27.898: %CMANRP-6-CMHASTATUS: RP switchover, received fastpath becoming active event *Sep 25 18:08:28.224: %CMANRP-6-CMHASTATUS: RP switchover, received chassis event to become active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
104
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
*Sep 25 18:08:28.229: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun *Sep 25 18:08:28.243: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT) *Sep 25 18:08:28.243: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN) *Sep 25 18:08:28.243 Manual Swact = enabled *Sep 25 18:08:27.956: %SYS-5-SWITCHOVER: Switchover requested by Exec. Reason: redundancy force-switchover.: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE) *Sep 25 18:08:28.248: %PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after chassis confirmation *Sep 25 18:08:28.249: %CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active *Sep 25 18:08:28.497: %PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event became active. Switch to primary (count 1) *Sep 25 18:08:30.630: %LINK-3-UPDOWN: Interface Null0, changed state to up *Sep 25 18:08:30.631: %LINK-3-UPDOWN: Interface Loopback0, changed state to up *Sep 25 18:08:30.635: %LINK-5-CHANGED: Interface POS0/0/0, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface POS0/1/0, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface POS0/1/1, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface GigabitEthernet0/3/0, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface GigabitEthernet0/3/1, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface GigabitEthernet0/3/2, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface GigabitEthernet0/3/3, changed state to administratively down *Sep 25 18:08:30.636: %LINK-5-CHANGED: Interface GigabitEthernet0/3/4, changed state to administratively down *Sep 25 18:08:31.630: %LINEPROTO-5-UPDOWN: Line protocol on Interface Null0, changed state to up *Sep 25 18:08:31.630: %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up *Sep 25 18:09:16.667: %REDUNDANCY-3-IPC: IOS versions do not match. *Sep 25 18:09:16.717: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 18:09:16.717: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Sep 25 *Sep 25 Router# Chassis 18:11:00.500: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded 18:11:00.502: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) show platform type: ASR1004 Type ------------------ASR1000-SIP10 SPA-1XOC12-POS SPA-2XOC3-POS SPA-5X1GE-V2 ASR1000-RP1 State --------------------ok ok ok ok ok ok, standby ok, active ok, active ok ok Insert time (ago) ----------------00:14:44 00:04:02 00:04:02 00:04:02 00:14:44 00:02:01 00:05:57 00:14:44 00:13:54 00:13:54
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
105
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Slot --------0 R0 F0
Router# Router# issu loadversion rp 0 file bootflash:asr1000rp1-{rpaccess,rpios,rpcontrol}*02.02.01.122-33.XNB1*.pkg bay 0 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
106
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software *Sep 25 18:13:53.696: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Sep 25 18:13:53.696: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Sep 25 18:13:53.697: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) Applying final IPC and database definitions *Sep 25 18:13:59.457: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# Router# Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed
*Sep 25 18:14:47.299: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 18:14:47.299: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 0 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
107
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP0 Applying final IPC and database definitions *Sep 29 11:05:40.249: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 0 *Sep 29 11:05:40.250: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled *Sep 29 11:05:40.250: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled *Sep 29 11:05:40.250: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/3, interfaces disabled Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
108
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
SUCCESS: Finished installing software. Router# *Sep 29 11:06:23.227: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0 Router# Router# *Sep 29 11:06:24.624: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Sep 29 11:06:25.379: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/1 Router# *Sep 29 11:06:26.306: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/3 Router# *Sep 29 11:06:33.776: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 0/0 Router# *Sep 29 11:06:33.934: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up Router# Router# *Sep 29 11:06:37.496: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up Router# Router# Router# *Sep 29 11:06:43.820: %SPA_OIR-6-ONLINECARD: SPA (SPA-2XOC3-POS) online in subslot 0/1 Router# *Sep 29 11:06:42.046: %LINK-3-UPDOWN: SIP0/3: Interface EOBC0/1, changed state to up Router# *Sep 29 11:06:48.410: %SPA_OIR-6-ONLINECARD: SPA (SPA-5X1GE-V2) online in subslot 0/3 Router# Router# Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# Router# issu loadversion rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 1 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
109
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router#issu loadversion rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*.pkg force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
110
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
--- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP0 Applying final IPC and database definitions *Sep 25 18:22:56.525: %ASR1000_OIR-6-OFFLINECARD: Card (fp) offline in slot F0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
111
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software.
Router# *Sep 25 18:23:45.207: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0 Router# Router# *Sep 25 18:23:55.309: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of 5) ready. *Sep 25 18:23:55.698: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /usr/cpp/bin/cpp-mcplo-ucode *Sep 25 18:23:55.931: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /usr/cpp/bin/cpp-mcplo-ucode Router# *Sep 25 18:24:00.837: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /usr/cpp/bin/cpp-mcplo-ucode *Sep 25 18:24:01.077: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete Router# *Sep 25 18:24:01.077: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system configuration start. Router# *Sep 25 18:24:02.403: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Sep 25 18:24:02.597: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system enabled. *Sep 25 18:24:02.598: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system initialization complete. Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed
Router# issu loadversion rp 0 file bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP WARNING: Automatically setting the on-reboot flag Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
112
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# show version provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: aca136bd8bcb99f87e6aa7a0ce2a92a3b5a5a200 Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/0 --More-Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
113
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: active File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 --More-Package: rpbase, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_ 1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 32b3fceaf59e3acd7cf9937ef33a822d6b359887 Package: rpaccess, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_010 0_1.pkg, on: RP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: 7c8dfdf9b2e3602b0c6c531a88dd93c8d2d180c6 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive --More-File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpcontrol, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_01 00_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a544cd10841b237066ccbc4714f4e23c00a9d2e5 Package: rpios-adventerprisek9, version: BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1, status: inactive File: bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST _20080924_0100_1.pkg, on: RP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: a4967ac35d6ac37ef275b28e032773762be9f202 Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: ESP0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
114
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown --More-Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: ESP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP0/2 --More-Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: active File: unknown, on: SIP0/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/1 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown --More-Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP1/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
115
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
File: unknown, on: SIP2/0 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/1 Built: 2008-09-24_03.52, by: mcpre --More-File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/2 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown Package: rpios-adventerprisek9, version: unknown, status: inactive File: unknown, on: SIP2/3 Built: 2008-09-24_03.52, by: mcpre File SHA1 checksum: unknown
Router# reload <some output removed for brevity> Router# request platform software package clean Cleaning up unnecessary package files No path specified, will use booted path bootflash:packages.conf Cleaning bootflash: Scanning boot directory for packages ... done. Preparing packages list to delete ... asr1000rp1-espbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_ 0100_1.pkg File is in use, will not delete. asr1000rp1-sipbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-sipspa.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. Files that will be deleted: asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.bin asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1 .bin asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100 _1.conf
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
116
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_200809 24_0100_1.conf asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1. pkg asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg packages.conf.00packages.conf.01packages.conf.02packages.conf.03packages.conf.04packages.conf.05Do you want to proceed? [confirm]y Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.p kg ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_010 0_1.bin ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080 924_0100_1.bin ... done. Deleting file bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200 80924_0100_1.conf ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LAT EST_20080924_0100_1.conf ... done. Deleting file bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g ... done. Deleting file bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:packages.conf.00- ... done. Deleting file bootflash:packages.conf.01- ... done. Deleting file bootflash:packages.conf.02- ... done. Deleting file bootflash:packages.conf.03- ... done. Deleting file bootflash:packages.conf.04- ... done. Deleting file bootflash:packages.conf.05- ... done.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
117
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (request platform Command Set)
This section provides instructions on using software upgrade for Cisco ASR 1002 or 1004 Router running subpackages using the request platform command set. These instructions assume two IOS processes are active on the RP and that the router is already running using subpackages. For information on checking and configuring two IOS processes on the same RP, see the Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (software upgrade Command Set) section on page 93.
SUMMARY STEPS
1.
show version show version installed dir filesystem:<directory> show platform show redundancy-states
2.
3. 4. 5. 6. 7. 8.
mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP request platform software package install rp 0 file file-system:asr1000rp1-{rpaccess,rpios,rpcontrol}*version-string*.pkg bay standby-bay force
9.
10. redundancy force-switchover 11. show platform 12. request platform software package install rp 0 file
file-system:asr1000rp1-{sipbase,sipspa}*version*.pkg slot SIP-slot-number Repeat the step 13, for each available SIP installed in the router before moving onto the next step.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
118
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
force
15. request platform software package install rp 0 file file-system:asr1000rp*version*.pkg 16. show version provisioned 17. reload 18. request platform software package clean
Note
Step 16, 17, 18 does not have to be performed immediately, and can be done at a convenient time.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
119
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
DETAILED STEPS
Command or Action
Step 1
show version show version installed dir filesystem :<directory> show platform show redundancy-states
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed dir bootflash: show platform show redundancy-states
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs. show redundancy statesConfirm the operational and configured redundancy states. Save the configuration after making this configuration step.
Step 2
Example:
Router(config)# redundancy Router(config-red)# mode sso
Step 3
mkdir
URL-to-directory-name
Create a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router# mkdir usb0:221subs
Step 4
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 5
copy tftp:
URL-to-target-location
Copy the consolidated package file into the directory created in Step 3. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: usb0:221subs
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
120
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 6
request platform software package expand file
Purpose Extract the subpackages out of the consolidated package file into the temporary directory.
Note
URL-to-consolidated-package
Example:
Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.0 1.122-33.XNB1.bin
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 7
dir
target-URL
(Optional) Display the directory to confirm that the files were extracted.
Example:
Router# dir usb0:221subs
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
121
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 8
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-3 3.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33. XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.12233.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.0 2.02.01.122-33.XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33 .XNB1.pkg bootflash: Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33. XNB1.pkg bootflash:
Step 9
request platform software package install rp 0 file file-system:asr1000rp1-{rpaccess,rpios,rpcontrol }*version-string *.pkg bay standby-bay force
Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay.
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-{rpaccess,rpios,rpcontrol} *02.02.01.122-33.XNB1*.pkg bay 1 force
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
122
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 10
redundancy force-switchover
Purpose Force a switchover from the active IOS process to the standby IOS process.
Note
Example:
Router# redundancy force-switchover
Your connection to the router often drops and is expected behavior at this point of the procedure in many scenarios. If this step drops your connection to the router, wait a few minutes before reconnecting to the router and then continue to Step 11.
Step 11
(Optional) Monitor system state to ensure both IOS processes are active.
Example:
Router# show platform
Step 12
request platform software package install rp 0 file file-system:asr1000rp1-{rpaccess,rpios,rpcontrol }*version-string *.pkg bay standby-bay force
Upgrade the RPAccess, RPIOS, and RPControl subpackages in the standby bay, which in this context is the opposite bay used in Step 9.
Note
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-{rpaccess,rpios,rpcontrol} *02.02.01.122-33.XNB1*.pkg bay 0 force
The pattern options used in this CLI (rpaccess, rpios, and rpcontrol) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Step 13
request platform software package install rp 0 file file-system:asr1000rp1-{sipbase,sipspa}*version*. pkg slot SIP-slot-number force Repeat this step for each SIP installed in your router before proceeding to the next step.
Upgrade the SIP and SPA subpackages for each SIP on the router.
Note
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 0 force Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 1 force Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01. 122-33.XNB1*.pkg slot 2 force
Tip
Note
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
123
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Command or Action
Step 14
request platform software package install rp 0 file file-system :asr1000rp1-esp*version *.pkg force
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*. pkg force
Step 15
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg
Upgrade all subpackages, including the RPBase subpackage, which is the last subpackage that needs to be upgraded.
Note
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Step 16
Example:
Router# show version installed
Step 17
reload
Example:
Router# reload
The router will continue normal operation even without a reload, so you can reload the router during scheduled maintenance or a slower traffic period.
Step 18
Examples
The following example shows the software upgrade for Cisco ASR 1002 or 1004 Router running sub-packages:
Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) <output removed for brevity> System image file is "bootflash:packages.conf" <output removed for brevity> cisco ASR1004 (RP1) processor with 752142K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 2 Serial interfaces 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 937983K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at bootflash:. 253424K bytes of USB flash at usb0:. Configuration register is 0x2102 Router# show version installed
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
124
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 9172d30751d79fc1afb7b405eca244bbf9f8f2f2 Package: rpbase, version: 02.01.00.122-33.XNA, status: active File: bootflash:asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg, on: RP0 Built: 2008-05-01_01.48, by: mcpre File SHA1 checksum: c09fe08ff908c8ce0b789d8acc774fe43dacf5e3 Package: rpaccess, version: 02.01.01.122-33.XNA, status: active File: bootflash:asr1000rp1-rpaccess.02.01.01.122-33.XNA.pkg, on: RP0 Built: 2008-07-08_16.01, by: mcpre File SHA1 checksum: c1afc591c9cd198409820226c4f23d2647d0d138 <output removed for brevity>
Router# show redundancy states my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit ID = 48 Redundancy Mode (Operational) = sso Redundancy Mode (Configured) = sso Redundancy State = sso Maintenance Mode = Disabled Manual Swact = disabled (peer unit not yet in terminal standby state) Communications = Up client count = 67 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0 Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 0/3 R0 R0/0 R0/1 F0 P0 P1 Slot --------0 R0 F0 Type ------------------ASR1000-SIP10 SPA-1XOC12-POS SPA-2XOC3-POS SPA-5X1GE-V2 ASR1000-RP1 State --------------------ok ok ok ok ok ok, active ok, standby ok, active ok ok Insert time (ago) ----------------00:04:43 00:03:25 00:03:24 00:03:20 00:04:43 00:04:43 00:02:55 00:04:43 00:03:53 00:03:53
Router# mkdir usb0:221subs Create directory filename [221subs]? Created dir bootflash:221subs Router(config)# ip tftp source-interface gigabitethernet 0 Router# copy tftp: usb0:221subs Address or name of remote host []? 172.17.16.81 Source filename []? /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Destination filename [asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
125
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Accessing tftp://172.17.16.81//auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin... Loading /auto/users/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 880.002 secs (237759 bytes/sec) Router# request platform software package expand file usb0:221subs/asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir usb0:221subs Directory of usb0:/221subs/ 72013 -rw51904716 Oct 7 2008 15:46:02 -07:00 asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg 72004 -rw5773 Oct 7 2008 15:46:02 -07:00 asr1000rp1-packages-adventerprisek9.02.02.01.122-33.XNB1.conf 72014 -rw20533452 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg 72015 -rw22388940 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg 72016 -rw27961548 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg 72017 -rw50942156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg 72018 -rw36442316 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg 72019 -rw26366156 Oct 7 2008 15:46:03 -07:00 asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg 72005 -rw6290 Oct 7 2008 15:46:03 -07:00 packages.conf 72003 -rw224768204 Oct 7 2008 15:38:57 -07:00 asr1000rp1-adventerprisek9.02.02.01.122-33.XNB1.bin 928862208 bytes total (466358272 bytes free) Router# copy usb0:221subs/asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-espbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 51904716 bytes copied in 5.478 secs (9475122 bytes/sec)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
126
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Router# copy usb0:221subs/asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpaccess.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 20533452 bytes copied in 2.346 secs (8752537 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 22388940 bytes copied in 2.496 secs (8969928 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpcontrol.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27961548 bytes copied in 2.992 secs (9345437 bytes/sec) Router# copy usb0:221subs/asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-rpios-adventerprisek9.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 50942156 bytes copied in 5.719 secs (8907529 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipbase.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 36442316 bytes copied in 3.906 secs (9329830 bytes/sec) Router# copy usb0:221subs/asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg bootflash: Destination filename [asr1000rp1-sipspa.02.02.01.122-33.XNB1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
127
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
--- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
128
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
--- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software *Sep 25 11:23:41.962: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Sep 25 11:23:41.962: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Sep 25 11:23:41.962: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Sep 25 11:24:35.148: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 11:24:35.149: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Router# *Sep 25 11:24:36.067: %REDUNDANCY-3-IPC: IOS versions do not match. Router# *Sep 25 11:26:48.281: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded Router# *Sep 25 11:26:48.283: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# redundancy force-switchover Proceed with switchover to standby RP? [confirm] %ASR1000_INFRA-6-CONSOLE_ACTIVE: R0/1 console active. Press RETURN to get started!
*Sep 25 11:31:33.401: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun *Sep 25 11:31:33.438: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_NOT_PRESENT) *Sep 25 11:31:33.438: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_DOWN) *Sep 25 11:31:33.438: %REDUNDANCY-3-SWITCHOVER: RP switchover (PEER_REDUNDANCY_STATE_CHANGE) *Sep 25 11:31:33.442: %PLATFORM-6-HASTATUS: RP switchover, sent message became active. IOS is ready to switch to primary after Manual Swact = enabled *Sep 25 11:31:33.061: %SYS-5-SWITCHOVER: Switchover requested by Exec. Reason: redundancy force-switchover. chassis confirmation *Sep 25 11:31:33.446: %CMANRP-6-CMHASTATUS: RP switchover, received chassis event became active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
129
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
*Sep 25 11:31:33.692: became active. Switch *Sep 25 11:31:35.802: *Sep 25 11:31:35.803: *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:35.808: administratively down *Sep 25 11:31:36.802: to up *Sep 25 11:31:36.802: state to up *Sep 25 11:32:21.530:
%PLATFORM-6-HASTATUS_DETAIL: RP switchover, received chassis event to primary (count 1) %LINK-3-UPDOWN: Interface Null0, changed state to up %LINK-3-UPDOWN: Interface Loopback0, changed state to up %LINK-5-CHANGED: Interface POS0/0/0, changed state to %LINK-5-CHANGED: Interface POS0/1/0, changed state to %LINK-5-CHANGED: Interface POS0/1/1, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/3/0, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/3/1, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/3/2, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/3/3, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/3/4, changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface Null0, changed state %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed %REDUNDANCY-3-IPC: IOS versions do not match.
*Sep 25 11:32:21.615: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 11:32:21.615: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Sep 25 11:34:05.450: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Sep 25 11:34:05.453: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 0/3 R0 R0/0 R0/1 F0 P0 P1 Slot --------0 R0 F0 Type ------------------ASR1000-SIP10 SPA-1XOC12-POS SPA-2XOC3-POS SPA-5X1GE-V2 ASR1000-RP1 State --------------------ok ok ok ok ok ok, standby ok, active ok, active ok ok Insert time (ago) ----------------00:31:12 00:11:35 00:11:35 00:11:35 00:31:12 00:05:38 00:13:36 00:31:12 00:30:22 00:30:22
Router# request platform software package install rp 0 file bootflash:asr1000rp1-{rpaccess,rpios,rpcontrol}*02.02.01.122-33.XNB1*.pkg bay 0 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
130
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change WARNING: Connection may be lost during installation of IOS package Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Applying final IPC and database definitions *Sep 25 11:40:59.590: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Sep 25 11:40:59.591: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
131
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
*Sep 25 11:40:59.591: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Sep 25 11:41:05.397: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software
Generating
SUCCESS: Finished installing software. *Sep 25 11:41:50.937: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Sep 25 11:41:50.937: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Router# Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 0 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
132
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting SIP0 Applying final IPC and database definitions *Sep 29 10:11:16.631: %ASR1000_OIR-6-OFFLINECARD: Card (cc) offline in slot 0 *Sep 29 10:11:16.632: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled *Sep 29 10:11:16.632: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled *Sep 29 10:11:16.632: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/3, interfaces disabled Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Sep 29 Router# Router# *Sep 29 *Sep 29 Router# *Sep 29 Router# *Sep 29 Router# *Sep 29 Router# *Sep 29 Router# *Sep 29 Router#
10:12:01.833: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0 10:12:02.579: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/1 10:12:03.460: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/3 10:12:10.405: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up 10:12:16.944: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 0/0 10:12:15.024: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up 10:12:20.938: %SPA_OIR-6-ONLINECARD: SPA (SPA-2XOC3-POS) online in subslot 0/1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
133
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
*Sep 29 10:12:17.086: %LINK-3-UPDOWN: SIP0/3: Interface EOBC0/1, changed state to up Router# *Sep 29 10:12:23.640: %SPA_OIR-6-ONLINECARD: SPA (SPA-5X1GE-V2) online in subslot 0/3 Router# Router# Router# request platform software package install rp 0 file bootflash:asr1000rp1-{sipspa,sipbase}*02.02.01.122-33.XNB1*.pkg slot 1 force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
134
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# request platform software package install rp 0 file bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*.pkg force --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software Checking Checking Checking Checking Finished sets are identified as compatible IPC compatibility with running software candidate package set infrastructure compatibility infrastructure compatibility with running software package specific compatibility compatibility testing
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
135
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Finished impact testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP0 Applying final IPC and database definitions *Sep 25 12:43:27.892: %ASR1000_OIR-6-OFFLINECARD: Card (fp) offline in slot F0 Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Sep 25 12:44:11.960: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0 Router# Router# *Sep 25 12:44:21.256: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of 5) ready. *Sep 25 12:44:21.798: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /usr/cpp/bin/cpp-mcplo-ucode *Sep 25 12:44:21.909: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /usr/cpp/bin/cpp-mcplo-ucode Router# *Sep 25 12:44:26.763: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /usr/cpp/bin/cpp-mcplo-ucode *Sep 25 12:44:27.004: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete Router# *Sep 25 12:44:27.004: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system configuration start. Router# *Sep 25 12:44:28.321: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Sep 25 12:44:28.516: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system enabled. *Sep 25 12:44:28.517: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system initialization complete. Router# Router# request platform software package install rp 0 file bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg --- Starting file path checking ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
136
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
Finished file path checking --- Starting image file verification --Checking image file names Verifying image file locations Locating image files and validating name syntax Inspecting image file types WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP WARNING: Automatically setting the on-reboot flag Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. Router# reload Proceed with reload? [confirm]y New software will load on reboot.
Router# request platform software package clean Cleaning up unnecessary package files No path specified, will use booted path bootflash:packages.conf Cleaning bootflash: Scanning boot directory for packages ... done. Preparing packages list to delete ... asr1000rp1-espbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpaccess.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-rpcontrol.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
137
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Upgrade Process With Service Impact for Nonredundant Platforms
asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_ 0100_1.pkg File is in use, will not delete. asr1000rp1-sipbase.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. asr1000rp1-sipspa.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. Files that will be deleted: asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.pkg asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.bin asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1 .bin asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100 _1.conf asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_200809 24_0100_1.conf asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1. pkg asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg packages.conf.00packages.conf.01packages.conf.02packages.conf.03packages.conf.04packages.conf.05Do you want to proceed? [confirm]y Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000-rommon.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080924_0100_1.p kg ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_010 0_1.bin ... done. Deleting file bootflash:asr1000rp1-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LATEST_20080 924_0100_1.bin ... done. Deleting file bootflash:asr1000rp1-espbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200 80924_0100_1.conf ... done. Deleting file bootflash:asr1000rp1-packages-adventerprisek9.BLD_V122_33_XNB_ASR_02.02.01.122-33.XNB1_LAT EST_20080924_0100_1.conf ... done.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
138
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Minimal Disruptive Restart ISSU
Deleting file bootflash:asr1000rp1-rpaccess.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-rpcontrol.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pk g ... done. Deleting file bootflash:asr1000rp1-rpios-adventerprisek9.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_200809 24_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipbase.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:asr1000rp1-sipspa.BLD_V122_33_XNA_ASR_RLS1_THROTTLE_LATEST_20080924_0100_1.pkg ... done. Deleting file bootflash:packages.conf.00- ... done. Deleting file bootflash:packages.conf.01- ... done. Deleting file bootflash:packages.conf.02- ... done. Deleting file bootflash:packages.conf.03- ... done. Deleting file bootflash:packages.conf.04- ... done. Deleting file bootflash:packages.conf.05- ... done. SUCCESS: Files deleted.
Note
MDR upgrades (both consolidated and subpackage upgrades) are supported only on hardware-redundant dual route processor (RP) and Enhanced Services Processors (ESP) platforms. MDR reduces the downtime (time during which the data plane is unavailable) due to ISSU of a SIP and the SPA(s) within it. The downtime is reduced from 100 seconds to not more than 25 seconds on a SIP reload and from 30 seconds to not more than 10 seconds on a SPA reload. The reload time of a SIP or SPA using a MDR or a non-MDR upgrade remains the same. MDR for a SIP is permitted if following conditions are met:
Chassis is hardware redundant (dual RP and dual ESP) SIP-type supports MDR. At least one MDR-compatible SPA in the SIP should be present for the MDR process. All the SPAs associated with the SIP support MDR. Both the current software version and the upgrade software version must be ISSU and MDR compatible for both the SIPBase and SIPSPA subpackages for each SPA type that is present. The following SPAs support MDR:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
139
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Minimal Disruptive Restart ISSU
Starting with IOS XE release 3.10S and later, MDR support has been extended to include the following SPA's:
SPA-2XOC3-POS SPA-4XOC3-POS SPA-4XOC3-POS-V2 SPA-8XOC3-POS SPA-1XOC12-POS SPA-2XOC12-POS SPA-4XOC12-POS SPA-8XOC12-POS
Use the request platform software package verify and issu checkversion commands with the mdr option to verify the MDR upgrade compatibility of a consolidated package or an individual subpackage. When performing an ISSU upgrade, you can specify whether the upgrade should use MDR. If you do not specify this, the ISSU upgrade process will remain unchanged. For more information on ISSU upgrade for nonredundant platforms, see Upgrade Process With Service Impact for Nonredundant Platforms section on page 76.
MDR is not supported on non-hardware-redundant platforms, such as, Cisco ASR 1001 Router, Cisco ASR 1002 Router, Cisco ASR 1002-X Router, or Cisco ASR 1004 Router, and on hardware-redundant platforms without redundant hardware, such as, Cisco ASR 1006 router, or Cisco ASR 1013 router with only a single RP or ESP. MDR is not supported on SIP10. MDR does not support software downgrade. To use MDR, both the current software and the upgrade software must be ISSU and MDR compatible. If a SIP is performing an MDR upgrade the following events cannot be handled during the upgrade:
Fast Reroute (FRR) Automatic protection switching (APS) Ethernet over Multiprotocol Label Switching (EoMPLS) and pseudoWire (PW) down that
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
140
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Consolidated packages can only be upgraded using ISSU in dual Route Processor configurations. ISSU is not supported for consolidated package upgrades in single Route Processor configurations. If you want the RPs on your Cisco ASR 1000 Series router to be running using a consolidated package with MDR after the ISSU upgrade is complete, use the following instructions:
Note
This procedure will only work if the current RPs are already running consolidated packages.
SUMMARY STEPS
1. 2. 3. 4.
ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location copy source-file-system:filename standby-destination-filesystem dir URL-to-target-location dir URL-to-target-stby-location
5. 6. 7. 8. 9.
issu checkversion rp upgrade-rp-number file URL mdr {force} issu loadversion rp upgrade-rp-number file standby-file-system:filename mdr {force} issu runversion telnet ip-address port issu acceptversion
10. issu commitversion 11. show version, show version active-RP running, show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
141
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
DETAILED STEPS
Command or Action
Step 1
ip tftp
Purpose Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 2
standby-destination-filesystem
Example:
Router# copy tftp bootflash:
Step 3
source-file-system:filename standby-destination-filesystem
copy
Example:
Router# copy bootflash:asr1000rp1-adventerprisek9.03.08.01.S.153-1 .S1.bin stby-bootflash:
Step 4
dir dir
URL-to-target-location URL-to-target-stby-location
Example:
Router# dir bootflash: Router# dir stby-bootflash:
(Optional) Display the contents of the target directories to confirm the successful copy of the file package.
Step 5
Checks the ISSU MDR software packaging compatibility on the standby Route Processor (RP).
Step 6
Load the target consolidated package onto the standby RP. After you receive the message indicating that the terminal state has been reached, go on to Step 7.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
142
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Command or Action
Step 7
issu runversion
Example:
Router# issu runversion
If this command is entered before the terminal state is reached, a peer is not online or Standby RP is not in terminal state error message will be seen and the issu runversion command will not work. If the issu runversion command does not run for these reasons, wait for the terminal state is reached message to appear and retry the issu runversion command. You can also monitor the terminal state using the show platform command.
After ISSU runversion is completed, a switchover will automatically occur and the standby RP will become the active RP.
Step 8
telnet ip-address port
Example:
[unix-server-1 ~]$ telnet 172.17.52.157 2003 User Access Verification Username: user Password: ******** Router>
Log in to the RP being upgraded, preferably using the RPs console port, to complete the upgrade. (This is the new active RP, that was the standby RP prior to the ISSU process.)
Note
Ensure the hostname does not end in -stby after logging into the RP, as this indicates that the RP being accessed is still the standby RP.
There are many ways to log on to a console port. The example shows access to the console port from a UNIX host using telnet.
Step 9
issu acceptversion
(Optional) Stops the ISSU rollback timer. This step is optional as long as Step 10 is completed before the rollback timer expires. Completes the ISSU upgrade.
Example:
Router# issu acceptversion
Step 10
issu commitversion
Example:
Router# issu commitversion
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
143
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Command or Action
Step 11
show show show show show version version active-RP running version active-RP provisioned platform running-configuration
Purpose (Optional) Enter the show version, show platform, or show running-configuration commands to confirm that the upgrade completed successfully, as follows:
show versionConfirm that the correct software version is running on your router and that the RP was booted from the correct file. show running-configurationConfirm that the booting configuration, in particular the boot system statements, are correct. Use the show running-config | include boot command to display only the boot statements from the show running-configuration output. show platform Confirm that both RP0 and RP1 are correctly running as active and standby.
Tip
Step 12
hw-module slot RP-slot reload
Example:
Router# hw-module slot R0 reload
Examples
The following example shows how to perform consolidated package upgrade in a dual route processor configuration:
Router(config)# ip tftp source-interface gigabitethernet 0 Router#copy tftp: bootflash: Address or name of remote host []? 172.17.26.81 Source filename []? asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Destination filename [asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin]? Accessing tftp://172.17.26.81/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin... Loading asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin from 172.17.26.81 (via GigabitEthernet0/0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!! [OK - 577420028 bytes] 577420028 bytes copied in 317.985 secs (1815872 bytes/sec)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
144
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Router#copy bootflash: stby-bootflash: Source filename []? asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Destination filename [asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC <output removed for brevity> 577420028 bytes copied in 154.951 secs (3726469 bytes/sec) Router#dir bootflash: Directory of bootflash:/ 11 drwx 16384 Sep 26 2011 00:30:14 +00:00 208833 drwx 4096 Sep 26 2011 00:30:57 +00:00 48193 drwx 4096 Mar 12 2013 20:03:38 +00:00 128513 drwx 4096 Sep 23 2012 19:08:45 +00:00 192770 drwx 4096 Sep 23 2012 19:08:45 +00:00 16 -r-680 Oct 10 2012 20:27:21 +00:00 22 -rw1135306 Nov 30 2012 02:15:24 +00:00 224897 drwx 4096 Mar 12 2013 17:32:24 +00:00 13 -r-577995644 Mar 12 2013 21:17:20 +00:00 asr1000rp2-adventerprisek9.03.08.00.S.153-1.S.bin 14 -r-577420028 Mar 12 2013 21:34:48 +00:00 asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin 192769 drwx 4096 May 30 2012 03:36:18 +00:00 25 -rw0 Feb 26 2012 16:16:36 +00:00 1940303872 bytes total (683945984 bytes free) Router# dir stby-bootflash: Directory of stby-bootflash:/ 11 drwx 16384 Apr 28 2009 03:43:50 +00:00 16065 drwx 4096 Mar 12 2013 18:26:02 +00:00 208833 drwx 4096 May 30 2012 03:36:52 +00:00 48193 drwx 4096 Mar 12 2013 22:39:32 +00:00 64257 drwx 4096 Mar 12 2013 18:26:02 +00:00 224897 drwx 4096 Mar 12 2013 18:18:18 +00:00 112449 drwx 4096 Jan 26 2011 16:57:39 +00:00 12 -r-577995644 Mar 12 2013 21:17:47 +00:00 asr1000rp2-adventerprisek9.03.08.00.S.153-1.S.bin 14 -r-680 Sep 4 2012 23:29:00 +00:00 13 -r-577420028 Mar 12 2013 21:18:12 +00:00 asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin 20 -rw0 Feb 26 2012 16:16:36 +00:00 1940303872 bytes total (685084672 bytes free) lost+found .installer virt_strg_pool_bf .prst_sync .rollback_timer vman_fdb .ssh lost+found .ssh .prst_sync .rollback_timer .installer debug.conf policy-250.pkg vman_fdb
virt_strg_pool_bf virtual-instance-upgrade.conf
debug.conf
virtual-instance-upgrade.conf
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
145
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Router#issu checkversion rp 1 file stby-bootflash:asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting system installation readiness checking --Finished system installation readiness checking --- Starting image verification --Compatibility check with running software on active RP WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Finished image verification --- Starting mdr compatibility verification --Extracting consolidated package content Checking and verifying packages contained in consolidated package Creating candidate provisioning file Processing candidate provisioning file Finished mdr compatibility verification SUCCESS: Software is ISSU MDR compatible. Router# issu loadversion rp 1 file stby-bootflash:asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting system installation readiness checking --Finished system installation readiness checking --- Starting image verification --Compatibility check with running software on active RP WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
146
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Finished image verification --- Starting mdr compatibility verification --Extracting consolidated package content Checking and verifying packages contained in consolidated package Creating candidate provisioning file Processing candidate provisioning file Finished mdr compatibility verification --- Starting installation changes --Setting up image to boot on next reset Starting automatic rollback timer Finished installation changes SUCCESS: Software will now load. *Mar 14 19:55:44.264: %IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Mar 14 19:55:44.288: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 14 19:55:44.288: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Mar 14 19:55:44.288: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 14 19:55:46.347: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 14 19:55:46.357: % Redundancy mode change to SSO Router# *Mar 14 19:59:37.523: %IOSXE_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Mar 14 19:59:46.889: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 14 19:59:46.889: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Mar 14 19:59:49.794: %REDUNDANCY-3-IPC: IOS versions do not match. *Mar 14 20:00:58.364: %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! *Mar 14 20:00:58.777: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Mar 14 20:00:59.778: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
Router# issu runversion --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting switchover readiness checking --Finished switchover readiness checking SUCCESS: Standby RP will now become active Initiating active RP failover
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
147
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
Mar 14 20:02:19.797 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: reload fru action requested
Initializing Hardware ... Calculating the ROMMON CRC ... CRC is correct
System Bootstrap, Version 15.2(1r)S, RELEASE SOFTWARE Copyright (c) 1994-2011 by cisco Systems, Inc. Current image running: Boot ROM0 Last reset cause: LocalSoft [Output removed for brevity]
*Mar 14 20:08:51.197: %REDUNDANCY-3-PEER_MONITOR: PEER_FOUND event on standby *Mar 14 20:09:53.509: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.3(1)S, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Tue 27-Nov-12 11:13 by mcpre *Mar 14 20:10:00.174: %PLATFORM-6-RF_PROG_SUCCESS: RF state STANDBY HOT Router-stby>
At this point of the procedure, use your UNIX client to log in to the other RP:
[unix-server-1 ~]$ telnet 172.17.152.157 2013 User Access Verification Username: user Password: ******** Router> *Mar 14 20:02:15.767: *Mar 14 20:02:15.768: *Mar 14 20:02:15.768: *Mar 14 20:02:16.768: state to up *Mar 14 20:02:16.768: to up *Mar 14 20:02:16.768: changed state to down *Mar 14 20:02:16.768: to up *Mar 14 20:02:17.498: *Mar 14 20:02:17.498: *Mar 14 20:02:17.756: *Mar 14 20:02:17.757: *Mar 14 20:02:17.757: state to up *Mar 14 20:02:17.757: *Mar 14 20:02:17.765: administratively down *Mar 14 20:02:17.765: administratively down
Lsmpi0, changed state to up EOBC0, changed state to up LIIN0, changed state to up protocol on Interface Lsmpi0, changed
%LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF %LINK-3-UPDOWN: Interface Null0, changed state to up %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed %LINK-3-UPDOWN: Interface Loopback0, changed state to up %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to %LINK-5-CHANGED: Interface GigabitEthernet0/0/2, changed state to
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
148
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
*Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/0/3, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/0/4, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/0/5, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/0/6, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/0/7, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/1/0, changed state to administratively down *Mar 14 20:02:17.765: %LINK-5-CHANGED: Interface GigabitEthernet0/1/1, changed state to administratively down *Mar 14 20:02:18.756: %LINEPROTO-5-UPDOWN: Line protocol on Interface Null0, changed state to up *Mar 14 20:02:18.757: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/0, changed state to up *Mar 14 20:04:05.534: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 14 20:04:05.863: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 14 20:04:07.781: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F1 *Mar 14 20:04:11.123: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 14 20:04:11.342: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization complete *Mar 14 20:04:11.472: %IOSXE-6-PLATFORM: F1: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Mar 14 20:04:19.443: %PLATFORM-5-RESETCARD: R1/0: card_reset: ESP0 reset to acquire provisioned software *Mar 14 20:04:19.458: %IOSXE_OIR-6-OFFLINECARD: Card (fp) offline in slot F0 *Mar 14 20:04:21.546: %MDR-5-CARD_RESTART: R1/0: card_mdr: Minimal Disruptive Restart SIP0 to acquire provisioned software *Mar 14 20:04:29.266: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA0 initiated Minimal Disruptive Restart *Mar 14 20:04:29.269: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA1 initiated Minimal Disruptive Restart *Mar 14 20:04:29.270: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA2 initiated Minimal Disruptive Restart *Mar 14 20:05:17.807: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Mar 14 20:05:21.287: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Mar 14 20:05:21.630: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1 *Mar 14 20:05:21.896: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Mar 14 20:05:29.364: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up *Mar 14 20:05:34.058: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/0 *Mar 14 20:05:33.064: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA0 completed Minimal Disruptive Restart *Mar 14 20:05:34.093: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up *Mar 14 20:05:35.125: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/1 *Mar 14 20:05:34.130: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA1 completed Minimal Disruptive Restart *Mar 14 20:05:34.099: %TRANSCEIVER-6-INSERTED: SIP0/1: transceiver module inserted in GigabitEthernet0/1/0 *Mar 14 20:05:35.046: %LINK-3-UPDOWN: SIP0/0: Interface GigabitEthernet0/0/0, changed state to up *Mar 14 20:05:37.996: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up *Mar 14 20:05:43.230: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/2 *Mar 14 20:05:42.239: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA2 completed Minimal Disruptive Restart *Mar 14 20:06:10.368: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 14 20:06:10.697: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
149
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Perform a Consolidated Package Upgrade in a Dual Route Processor Configuration with MDR
*Mar 14 20:06:12.158: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0 *Mar 14 20:06:15.940: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 14 20:06:16.158: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete *Mar 14 20:06:16.290: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Mar 14 20:08:41.564: %IOSXE_OIR-6-ONLINECARD: Card (rp) online in slot R0 *Mar 14 20:08:51.188: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 14 20:08:51.188: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Mar 14 20:08:54.115: %REDUNDANCY-3-IPC: IOS versions do not match. *Mar 14 20:10:00.611: %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! *Mar 14 20:10:01.026: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Mar 14 20:10:02.027: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router>enable
Router# issu acceptversion --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 Cancelling rollback timer SUCCESS: Rollback timer cancelled
Router# issu commitversion --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting commit readiness checking --Finished commit readiness checking --- Starting installation changes --Cancelling rollback timer Saving image changes Finished installation changes Building configuration... [OK] SUCCESS: version committed: bootflash:asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin
After you confirm the software versions and configuration, reload the RP as shown in the following example:
Router# hw-module slot R0 reload Proceed with reload of module? [confirm] *Mar 14 20:31:05.511: %IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R0 *Mar 14 20:31:05.587: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 14 20:31:05.588: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Mar 14 20:31:05.588: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 14 20:31:07.622: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 14 20:31:07.632: % Redundancy mode change to SSO *Mar 14 20:34:29.337: %IOSXE_OIR-6-ONLINECARD: Card (rp) online in slot R0 *Mar 14 20:34:38.988: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4))
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
150
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
*Mar 14 20:34:38.988: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Mar 14 20:35:47.610: %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! *Mar 14 20:35:48.023: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Mar 14 20:35:49.025: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
This section provides instructions on performing an ISSU upgrade on a Cisco ASR 1000 Series Router with dual RPs that is currently running individual subpackages. This section covers the following topics:
Using ISSU to Upgrade the SubPackages on a Cisco ASR 1006 or ASR 1013 Router (issu Command Set) with MDR, page 151 Using ISSU to Upgrade SubPackages on a Cisco ASR 1006 Router or ASR 1013 Router (request platform command set) with MDR, page 185
Using ISSU to Upgrade the SubPackages on a Cisco ASR 1006 or ASR 1013 Router (issu Command Set) with MDR
This section provides the instructions for performing an ISSU upgrade using subpackages with MDR on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the issu command set. This procedure can only be performed if the current ASR 1006 or ASR 1013 routers have two active RPs and both RPs are running subpackages.
SUMMARY STEPS
1.
show version show version active-rp installed dir filesystem:<directory> show platform show redundancy-states
2. 3. 4. 5. 6. 7. 8.
copy running-config startup-config mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
151
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP
Note
In step 6, each individual subpackage that was extracted in step 4 is copied to the directory where the subpackages that are currently running the standby RP are stored. copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-standby-RP
9.
10. issu checkversion rp standby-RP file standy-file-system:asr1000rp*version*.pkg mdr {force} 11. issu loadversion rp standby-RP file URL-to-standby-file-system:asr1000rp*version*.pkg force 12. hw-module slot standby-RP reload 13. issu loadversion rp active-RP file
URL-to-active-file-system:asr1000rp1-{sipbase,sipspa}*version*.pkg slot SIP-slot-number mdr {force} issu commitversion Repeat this step for each SIP installed in the router before moving onto the next step.
14. issu loadversion rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot
standby-ESP-slot issu commitversion issu loadversion rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot active-ESP-slot issu commitversion
15. issu loadversion rp active-RP file URL-to-active-file-system:asr1000rp1*version*.pkg force 16. show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
152
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
DETAILED STEPS
Command or Action
Step 1
show version show version active-rp installed dir filesystem : directory show platform show redundancy states
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed dir bootflash: show platform show redundancy states
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs. show redundancy statesConfirm the operational and configured redundancy states.
Step 2
Example:
Router# copy running-config startup-config
After you have confirmed that the system states are acceptable, save the current configuration to the startup configuration. Create a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Step 3
mkdir
URL-to-directory-name
Example:
Router# mkdir bootflash:tmp
Step 4
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 5
copy tftp:
URL-to-target-location
Copy the consolidated package file into the directory created in Step 3. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: bootflash:tmp
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
153
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 6
request platform software package expand file
Purpose Extract the subpackages out of the consolidated package file into the temporary directory.
Note
URL-to-consolidated-package
Example:
Router# request platform software package expand file bootflash:tmp/asr1000rp2-adventerprisek9.03.08. 01.S.153-1.S1.bin
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 7
dir
target-URL
(Optional) Display the directory to confirm that the files were extracted.
Example:
Router# dir bootflash:tmp
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
154
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 8
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153 -1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.15 3-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.1531.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.1 53-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpios-adventerprisek9. 03.08.01.S.153-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153 -1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.1531.S1.pkg bootflash:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
155
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 9
Purpose Copy the subpackages out of the temporary directory into the directory on the router where the subpackages running the standby RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-standby-RP
copy
Examples:
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153 -1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.15 3-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.1531.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.1 53-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-adventerprisek9.03.08. 01.S.153-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153 -1.S1.pkg stby-bootflash: Router# ccopy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.1531.S1.pkg stby-bootflash:
Step 10
Checks the ISSU MDR software packaging compatibility on the standby Route Processor (RP).
Step 11
standby-RP file Upgrade the RP subpackages on the standby RP, where the target-standbyRP-URL-for-sub-packages:asr1000rp* rp* wildcard is specified to capture all of the RP version*.pkg force subpackages for the desired upgrade release.
issu loadversion rp
Example:
Router# issu loadversion rp 1 file stby-bootflash:asr1000rp2-*03.08.01*pkg force
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
156
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 12
hw-module slot
standby-RP reload
Example:
Router# hw-module slot R1 reload
Step 13
Upgrade the SIP and SPA subpackages for each SIP on the router using MDR.
Note
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Tip
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp2-{sipbase,sipspa}*03.08.01* pkg mdr Router# issu commitversion
Note
Step 14
active-RP file Upgrade the ESP Base subpackage on the standby and the URL-to-active-file-system:asr1000rp1-esp*version*. active ESPs. pkg slot standby-ESP-slot issu commitversion After entering the issu loadversion rp command on the issu loadversion rp active-RP file active RP, the ESP switchover will occur automatically. URL-to-active-file-system:asr1000rp1-esp*version*. Minimal traffic interruption will occur as a result of this pkg slot active-ESP-slot switchover. issu commitversion
issu loadversion rp
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 1 Router# issu commitversion Router# issu loadversion rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 0 Router# issu commitversion
Step 15
Example:
Router# issu loadversion rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg force
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Step 16
Example:
Router# show version r0 provisioned Router# show version r0 installed
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
157
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 17
redundancy force-switchover
Example:
Router# redundancy force-switchover
Step 18
Example:
Router# request platform software package clean
Examples
The following example shows ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the issu command set
Router# show version Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.3(1)S, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Tue 27-Nov-12 11:13 by mcpre <output removed for brevity> System image file is "bootflash:packages.conf" Last reload reason: Reload Command <output removed for brevity> Router# show platform Chassis type: ASR1006 Slot --------0 0/0 0/1 0/2 R0 R1 F0 F1 P0 P1 Slot --------0 R0 R1 F0 F1 Type ------------------ASR1000-SIP40 SPA-8X1GE-V2 SPA-8X1GE-V2 SPA-8X1GE-V2 ASR1000-RP2 ASR1000-RP2 ASR1000-ESP40 ASR1000-ESP40 ASR1006-PWR-AC ASR1006-PWR-AC CPLD Version ------------------00200800 08103002 08103002 1003190E 1003190E State --------------------ok ok ok ok ok, active ok, standby ok, active ok, standby ps, fail ok Insert time (ago) ----------------00:07:13 00:06:05 00:06:05 00:05:57 00:07:13 00:07:13 00:07:13 00:07:13 00:06:23 00:06:22
Router# show version r0 installed Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 994420f6eb61a67d1838dfc083489f1b84a80dc9 Package: rpbase, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
158
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP0/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP0/1 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP0/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
159
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: espbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg, on: ESP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 2dcf4ace7236e77055f580a84628c6d802ef8c3b Package: espx86base, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg, on: ESP0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: b07dfcd9eb3fe00cd52c27a2ff261b190036dc39 Package: espbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg, on: ESP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 2dcf4ace7236e77055f580a84628c6d802ef8c3b Package: espx86base, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg, on: ESP1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: b07dfcd9eb3fe00cd52c27a2ff261b190036dc39 Package: sipbase, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 --More--
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
160
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
*Mar 14 20:56:35.827: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: inactive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
161
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
162
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP4 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP4 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
163
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP5 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP5 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/3 Built: 2012-11-27_13.54, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
164
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365
Router#copy tftp: bootflash:tmp Address or name of remote host []? 172.17.16.87 Source filename []? asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Destination filename [asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin]? Accessing tftp://172.17.16.87 /asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin... Loading asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin from 172.17.16.87 (via GigabitEthernet0/0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!! [OK - 577420028 bytes] 577420028 bytes copied in 317.985 secs (1815872 bytes/sec)
Router# request platform software package expand file bootflash:tmp/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router#dir bootflash:tmp Directory of bootflash:/tmp/ 144578 -r-- 577420028 May 13 2013 00:12:46 +00:00 asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
165
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
208843 -rw- 33223408 May 13 2013 00:14:30 +00:00 asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg 208844 -rw- 49169136 May 13 2013 00:14:30 +00:00 asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg 208845 -rw- 80138996 May 13 2013 00:14:30 +00:00 asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg 208846 -rw- 98632436 May 13 2013 00:14:30 +00:00 asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg 208841 -rw- 9139 May 13 2013 00:14:30 +00:00 asr1000rp2-packages-adventerprisek9.03.08.01.S.153-1.S1.conf 208847 -rw- 27165428 May 13 2013 00:14:30 +00:00 asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg 208848 -rw- 49359604 May 13 2013 00:14:30 +00:00 asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg 208849 -rw- 45224692 May 13 2013 00:14:30 +00:00 asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg 208850 -rw- 110813948 May 13 2013 00:14:30 +00:00 asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg 208851 -rw- 41722612 May 13 2013 00:14:30 +00:00 asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg 208852 -rw- 59964148 May 13 2013 00:14:30 +00:00 asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg 208842 -rw- 9919 May 13 2013 00:14:30 +00:00 packages.conf 1940303872 bytes total (87834624 bytes free) Router#
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 80138996 bytes copied in 5.280 secs (15177840 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27165428 bytes copied in 1.771 secs (15339033 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 49359604 bytes copied in 3.232 secs (15272155 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
166
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 45224692 bytes copied in 2.971 secs (15222044 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 110813948 bytes copied in 8.257 secs (13420607 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 41722612 bytes copied in 2.754 secs (15149823 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 59964148 bytes copied in 3.899 secs (15379366 bytes/sec)
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 80138996 bytes copied in 43.096 secs (1859546 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
167
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
27165428 bytes copied in 16.590 secs (1637458 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 49359604 bytes copied in 29.490 secs (1673774 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 45224692 bytes copied in 26.694 secs (1694189 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 110813948 bytes copied in 60.787 secs (1822988 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 41722612 bytes copied in 24.351 secs (1713384 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 59964148 bytes copied in 35.324 secs (1697547 bytes/sec) Router#issu checkversion rp 1 file stby-bootflash:asr1000rp2-*03.08.01*pkg mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
168
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
--- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting mdr compatibility verification --Finished mdr compatibility verification SUCCESS: Software is ISSU MDR compatible. Router#issu loadversion rp 1 file stby-bootflash:asr1000rp2-*03.08.01*pkg force --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
169
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
--- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-espbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
170
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Removed asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg New files list: Added asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# hw-module slot r1 reload Proceed with reload of module? [confirm] Router# *Mar 14 22:21:51.678: %IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Mar 14 22:21:51.690: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 14 22:21:51.690: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Mar 14 22:21:51.690: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 14 22:21:53.465: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 14 22:21:53.475: % Redundancy mode change to SSO *Mar 14 22:25:23.959: %IOSXE_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Mar 14 22:25:32.991: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 14 22:25:32.991: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Mar 14 22:25:35.944: %REDUNDANCY-3-IPC: IOS versions do not match. *Mar 14 22:26:45.418: %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! *Mar 14 22:26:45.833: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Mar 14 22:26:46.834: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO)
Router# issu loadversion rp 0 file bootflash:asr1000rp2-{sipbase,sipspa}*03.08.01*pkg mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
171
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting mdr compatibility verification --Finished mdr compatibility verification --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg New files list: Added asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
172
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
--- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software *Mar 14 22:32:39.826: %MDR-5-CARD_RESTART: R0/0: card_reset: Minimal Disruptive Restart SIP0 to acquire provisioned software Applying final IPC and database definitions *Mar 14 22:32:49.139: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA0 initiated Minimal Disruptive Restart *Mar 14 22:32:49.144: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA1 initiated Minimal Disruptive Restart *Mar 14 22:32:49.144: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: SPA2 initiated Minimal Disruptive Restart Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. *Mar 14 22:33:37.680: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Mar 14 22:33:41.161: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Mar 14 22:33:41.508: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1 *Mar 14 22:33:41.785: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Mar 14 22:33:49.531: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up *Mar 14 22:33:50.449: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/0 *Mar 14 22:33:49.584: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA0 completed Minimal Disruptive Restart *Mar 14 22:33:49.538: %TRANSCEIVER-6-INSERTED: SIP0/0: transceiver module inserted in GigabitEthernet0/0/0 *Mar 14 22:33:51.566: %LINK-3-UPDOWN: SIP0/0: Interface GigabitEthernet0/0/0, changed state to up *Mar 14 22:33:53.840: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up *Mar 14 22:33:58.613: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/1 *Mar 14 22:33:57.750: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA1 completed Minimal Disruptive Restart *Mar 14 22:33:59.721: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/2 *Mar 14 22:33:58.861: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA2 completed Minimal Disruptive Restart *Mar 14 22:33:57.884: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up Router# Router# Router# Router# Router# issu commitversion --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation changes ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
173
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed Router# issu loadversion rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 1 --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
174
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
--- Starting list of software package changes --No old package files removed New files list: Added asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Finished installation changes SUCCESS: Installation changes committed
Router# issu loadversion rp 0 file bootflash:asr1000rp2-*03.08.01*pkg force --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
175
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg New files list: Added asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
176
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Router# show version r0 provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: eca1c579979a1ffec0b1774307acfcdd71eb1449 Package: rpbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg, on: RP0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: e3cc362353e89c567f6401534abac8aa7f563131 Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg, on: RP1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: e3cc362353e89c567f6401534abac8aa7f563131 Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
177
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: espbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg, on: ESP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 857b318967cefc17c1af026467b5b4345c8e208a Package: espx86base, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: espbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg, on: ESP1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 857b318967cefc17c1af026467b5b4345c8e208a Package: espx86base, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
178
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
179
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP3 Built: 2012-11-27_13.54, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
180
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP4 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP4 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
181
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP5 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP5 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
182
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365
Router# show version r0 running Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: eca1c579979a1ffec0b1774307acfcdd71eb1449 Package: rpbase, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: espx86base, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP0 Built: 2013-02-08_14.10, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
183
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: espx86base, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: sipbase, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: sipspa, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: sipspa, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: sipspa, version: 03.08.01.S.153-1.S1, status: active File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Router# redundancy force-switchover Proceed with switchover to standby RP? [confirm] Manual Swact = enabled <output removed for brevity>
*Mar 14 23:04:31.468: %REDUNDANCY-3-PEER_MONITOR: PEER_FOUND event on standby *Mar 14 23:05:32.827: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.3(1)S1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Fri 08-Feb-13 10:19 by mcpre *Mar 14 23:05:33.041: %SYS-6-BOOTTIME: Time taken to reboot after reload = 287 seconds
Router# request platform software package clean Cleaning up unnecessary package files No path specified, will use booted path bootflash:packages.conf Cleaning bootflash: Scanning boot directory for packages ... done. Preparing packages list to delete ... asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg File is in use, will not delete.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
184
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. Files that will be deleted: asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg asr1000rp2-espbase.03.08.00.S.153-1.S.pkg asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg asr1000rp2-packages-adventerprisek9.03.08.00.S.153-1.S.conf asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg packages.conf.00Do you want to proceed? [confirm]y Deleting file bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-packages-adventerprisek9.03.08.00.S.153-1.S.conf ... done. Deleting file bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:packages.conf.00- ... done. SUCCESS: Files deleted.
Using ISSU to Upgrade SubPackages on a Cisco ASR 1006 Router or ASR 1013 Router (request platform command set) with MDR
This procedure can only be performed if the current ASR 1006 router or ASR 1013 router has two active RPs and both RPs are running subpackages. To perform an ISSU upgrade with MDR using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup using the request platform command set, follow the following instructions.
SUMMARY STEPS
1.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
185
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
mkdir URL-to-directory-name ip tftp source-interface gigabitethernet slot/port copy tftp: URL-to-target-location request platform software package expand file URL-to-consolidated-package dir URL-to-consolidated-package copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-rpios.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system:asr1000rp1-sipspa.version.pkg URL-to-directory-of-sub-packages-standby-RP request platform software package verify rp slot file URL mdr {force} URL-to-standby-file-system:asr1000rp*version*.pkg force
8.
9.
10. request platform software package install rp standby-RP file 11. hw-module slot standby-RP reload 12. request platform software package install rp active-RP file URL-to-active-file-system:image slot
SIP-slot-number mdr {force} Repeat this step for each SIP installed in the router before moving onto the next step.
13. request platform software package install rp active-RP file
URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot standby-ESP-slot request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*.pkg slot active-ESP-slot
14. request platform software package install rp active-RP file
URL-to-active-file-system:asr1000rp*version*.pkg force
15. show version active-RP provisioned
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
186
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
187
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
DETAILED STEPS
Command or Action
Step 1
show version show version active-rp installed show version standby-rp installed dir filesystem :<directory> show platform
Purpose (Optional) Use the following commands to confirm the current router configuration, as follows:
Example:
Router# Router# Router# Router# Router# show version show version r0 installed show version r1 installed dir bootflash: show platform
show version and show version active-rp installedVerify the running version of the Cisco IOS XE software on the router, and which file was used to boot the router, and where that file is stored. dirConfirm that the files that were used to boot the router are located in the directory. show platformConfirm the current status of the active and standby RPs.
Step 2
mkdir
URL-to-directory-name
Creates a directory to store the consolidated package and subpackages. This directory must be created in most cases because the consolidated packages and subpackages have to be separated from the subpackages that booted the router at this step of the procedure. Specifies the Gigabit Ethernet TFTP source-interface to be configured: slot/portSpecifies the location of the TFTP source-interface.
Note
Example:
Router# mkdir bootflash:tmp
Step 3
ip tftp
Example:
Router(config)# ip tftp source-interface gigabitethernet 0
To copy a file using TFTP through the Management Ethernet interface, the ip tftp source-interface GigabitEthernet 0 command must be entered before entering the copy tftp command.
Step 4
copy tftp:
URL-to-target-location
Copies the consolidated package file into the directory created in Step 2. The consolidated package in this step should not be copied into the same directory where the subpackages that are currently running your router are stored (the directory containing the packages.conf provisioning file from which the router was booted).
Tip
Example:
Router# copy tftp: bootflash:tmp
It is recommended that you copy the package onto a usb: or harddisk: file system for space considerations when performing this step of the procedure.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
188
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 5
request platform software package expand file
Purpose Extracts the subpackages out of the consolidated package file into the temporary directory.
Note
URL-to-consolidated-package
Example:
Router# request platform software package expand file bootflash:tmp/asr1000rp2-adventerprisek9.03.08. 01.S.153-1.S1.bin
Take extra care to extract the subpackages to a temporary subdirectory and do not delete any of the files currently running the router at this point of the procedure. To erase the files that were running on the router before the ISSU upgrade, enter the request platform software package clean command after the ISSU upgrade has been completed.
Step 6
dir
target-URL
(Optional) Displays the directory to confirm that the files were extracted.
Example:
Router# dir bootflash:tmp
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
189
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 7
Purpose Copies the subpackages out of the temporary directory into the directory on the router where the subpackages running the active RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-active-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-active-RP
copy
Example:
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153 -1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.15 3-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.1531.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.1 53-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-rpios-adventerprisek9. 03.08.01.S.153-1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153 -1.S1.pkg bootflash: Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.1531.S1.pkg bootflash:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
190
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 8
Purpose Copies the subpackages out of the temporary directory into the directory on the router where the subpackages running the standby RP are currently stored.
file-system:asr1000rp1-espbase.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpaccess.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpcontrol.version.pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-rpios.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipbase.version .pkg URL-to-directory-of-sub-packages-standby-RP copy file-system :asr1000rp1-sipspa.version .pkg URL-to-directory-of-sub-packages-standby-RP
copy
Example:
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153 -1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.15 3-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.1531.S1.pkg stby-bootflash: Router# ccopy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.1 53-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-adventerprisek9.03.08. 01.S.153-1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153 -1.S1.pkg stby-bootflash: Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.1531.S1.pkg stby-bootflash:
Step 9
request platform software package verify rp slot file URL mdr {force}
Example:
Router# request platform software package verify rp 1 file stby-bootflash:asr1000rp2-*03.08.01*.pkg mdr
Verifies the RP subpackages on the standby RP, where the rp* wildcard is specified to capture all of the RP subpackages for the desired upgrade release.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
191
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 10
request platform software package install rp standby-RP file target-standbyRP-URL-for-sub-packages:asr1000rp* version*.pkg force
Purpose Upgrades the RP subpackages on the standby RP, where the rp* wildcard is specified to capture all of the RP subpackages for the desired upgrade release.
Example:
Router# request platform software package install rp 1 file stby-bootflash:asr1000rp2-*03.08.01*.pkg force
Step 11
hw-module slot
standby-RP reload
Example:
Router# hw-module slot R1 reload
Step 12
request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-{sipbase,sip spa}*version *.pkg slot SIP-slot-number mdr
Upgrades the SIP and SPA subpackages for each SIP on the router using MDR.
Note
{force} Repeat this step for each SIP installed in the router before moving onto the next step.
Tip
This step must be completed one SIP at a time, and repeated for each SIP installed on the router before performing the next step. You can use the show ip interface brief command to identify which slots contain SIPs and SPAs. The interfaces with three numbers (in the form SIP-number/SPA-number/interface-number) identify the SIP and SPA locations in the router. The pattern options used in this CLI (sipbase and sipspa) were introduced in Cisco IOS XE Release 2.1.2 and are not available in previous Cisco IOS XE Releases. See the ISSU Procedures (Prior to Cisco IOS XE Release 2.1.2) section on page 74 for pre-Cisco IOS XE Release 2.1.2 ISSU upgrade procedures.
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp2-{sipb rp 0 file bootflash:asr1000rp2-{sipbase,sipspa}*03.08.01* pkg mdr
Note
Step 13
request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp1-esp*version*. pkg slot standby-ESP-slot
Upgrades the ESP Base subpackage on the standby and the active ESPs.
After entering the issu loadversion rp command on the active RP, the ESP switchover will occur automatically. request platform software package install rp Minimal traffic interruption will occur as a result of this active-RP file URL-to-active-file-system:asr1000rp1-esp*version*. switchover. pkg slot active-ESP-slot
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 1 Router# request platform software package install rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
192
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Command or Action
Step 14
request platform software package install rp active-RP file URL-to-active-file-system:asr1000rp*version*.pkg force
Example:
Router# request platform software package install rp 0 file bootflash:asr1000rp2-*03.08.01*.pkg force
This step is required to ensure that all subpackages on the router were upgraded as part of this procedure, and might upgrade some subpackages that would otherwise be missed in the process.
Step 15
Example:
Router# show version r0 provisioned Router# show version r0 installed
Step 16
redundancy force-switchover
Example:
Router# redundancy force-switchover
Step 17
Examples
This example shows ISSU upgrade using subpackages on a Cisco ASR 1006 router or ASR 1013 router with a dual RP setup:
Router# show version Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.3(1)S, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Tue 27-Nov-12 11:13 by mcpre IOS XE Version: 03.08.00.S Cisco IOS-XE software, Copyright (c) 2005-2012 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: IOS-XE ROMMON Router uptime is 3 minutes Uptime for this control processor is 5 minutes System returned to ROM by reload System image file is "bootflash:packages.conf" Last reload reason: Reload Command <output removed for brevity>
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
193
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Router# show platform Chassis type: ASR1006 Slot --------0 0/0 0/1 0/2 R0 R1 F0 F1 P0 P1 Slot --------0 R0 R1 F0 F1 Type ------------------ASR1000-SIP40 SPA-8X1GE-V2 SPA-8X1GE-V2 SPA-8X1GE-V2 ASR1000-RP2 ASR1000-RP2 ASR1000-ESP40 ASR1000-ESP40 ASR1006-PWR-AC ASR1006-PWR-AC CPLD Version ------------------00200800 08103002 08103002 1003190E 1003190E State --------------------ok ok ok ok ok, active ok, standby ok, active ok, standby ps, fail ok Insert time (ago) ----------------00:07:13 00:06:05 00:06:05 00:05:57 00:07:13 00:07:13 00:07:13 00:07:13 00:06:23 00:06:22
Router# show version r0 installed Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 994420f6eb61a67d1838dfc083489f1b84a80dc9 Package: rpbase, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP0/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP0/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP0/1 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP0/1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
194
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg, on: RP1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 260422fb9cb28321d92055eb8dae238291aa671c Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP1/0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: rpcontrol, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 7d362c705939a438994315f13e36fc2869218d92 Package: rpios-adventerprisek9, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.15, by: mcpre File SHA1 checksum: 1d48c0d5c4a5086f78808cfdb43b4420da59d3b7 Package: rpaccess, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg, on: RP1/1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: 48f96c898fc28196cc1632915022ce6c1d38e7c3 Package: espbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg, on: ESP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 2dcf4ace7236e77055f580a84628c6d802ef8c3b Package: espx86base, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg, on: ESP0 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: b07dfcd9eb3fe00cd52c27a2ff261b190036dc39 Package: espbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg, on: ESP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 2dcf4ace7236e77055f580a84628c6d802ef8c3b Package: espx86base, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg, on: ESP1 Built: 2012-11-27_16.07, by: mcpre File SHA1 checksum: b07dfcd9eb3fe00cd52c27a2ff261b190036dc39 Package: sipbase, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
195
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: active File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 --More-*Mar 14 20:56:35.827: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP0/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP0/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
196
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP1/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP1/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: inactive File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
197
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP2/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP2/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP3/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
198
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP3/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP4 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP4 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP4/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP4/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg, on: SIP5 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 608439b20059b8b58ffe12479208c25bd440759a Package: elcbase, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg, on: SIP5 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 904fdb7bd9ed36fe277498d43b6941095dbae0b1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
199
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/0 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/1 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/2 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Package: sipspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg, on: SIP5/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: 17e980066fa9c077ac1128f278a5d9ae81af7bc6 Package: elcspa, version: 03.08.00.S.153-1.S, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg, on: SIP5/3 Built: 2012-11-27_13.54, by: mcpre File SHA1 checksum: ffc7e5a916a807e90d2b624e228ce6577f978365 Router#mkdir bootflash:tmp Create directory filename [tmp]? Created dir bootflash:/tmp Router(config)# ip tftp source-interface gigabitethernet 0 Router#copy tftp: bootflash:tmp Address or name of remote host []? 172.17.16.81 Source filename []? asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Destination filename [asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin]? Accessing tftp://172.17.16.81/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin... Loading asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin from 172.17.16.81 (via GigabitEthernet0/0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
200
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!! [OK - 577420028 bytes] 577420028 bytes copied in 317.985 secs (1815872 bytes/sec) Router# request platform software package expand file bootflash:tmp/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router#dir bootflash:tmp Directory of bootflash:/tmp/ 144578 -r-- 577420028 May 13 2013 00:12:46 +00:00 asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.bin 208843 -rw- 33223408 May 13 2013 00:14:30 +00:00 asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg 208844 -rw- 49169136 May 13 2013 00:14:30 +00:00 asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg 208845 -rw- 80138996 May 13 2013 00:14:30 +00:00 asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg 208846 -rw- 98632436 May 13 2013 00:14:30 +00:00 asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg 208841 -rw- 9139 May 13 2013 00:14:30 +00:00 asr1000rp2-packages-adventerprisek9.03.08.01.S.153-1.S1.conf 208847 -rw- 27165428 May 13 2013 00:14:30 +00:00 asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg 208848 -rw- 49359604 May 13 2013 00:14:30 +00:00 asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg 208849 -rw- 45224692 May 13 2013 00:14:30 +00:00 asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg 208850 -rw- 110813948 May 13 2013 00:14:30 +00:00 asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg 208851 -rw- 41722612 May 13 2013 00:14:30 +00:00 asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg 208852 -rw- 59964148 May 13 2013 00:14:30 +00:00 asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg 208842 -rw- 9919 May 13 2013 00:14:30 +00:00 packages.conf 1940303872 bytes total (87834624 bytes free) Router#
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
201
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 80138996 bytes copied in 5.280 secs (15177840 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27165428 bytes copied in 1.771 secs (15339033 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 49359604 bytes copied in 3.232 secs (15272155 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 45224692 bytes copied in 2.971 secs (15222044 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 110813948 bytes copied in 8.257 secs (13420607 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 41722612 bytes copied in 2.754 secs (15149823 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg bootflash: Destination filename [asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg]?
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
202
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 59964148 bytes copied in 3.899 secs (15379366 bytes/sec)
Router# copy bootflash:tmp/asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg bootflash:: Destination filename [asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 80138996 bytes copied in 43.096 secs (1859546 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 27165428 bytes copied in 16.590 secs (1637458 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 49359604 bytes copied in 29.490 secs (1673774 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 45224692 bytes copied in 26.694 secs (1694189 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-adventerprisek9.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
203
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
110813948 bytes copied in 60.787 secs (1822988 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCC 41722612 bytes copied in 24.351 secs (1713384 bytes/sec) Router# copy bootflash:tmp/asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg stby-bootflash: Destination filename [asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg]? Copy in progress...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 59964148 bytes copied in 35.324 secs (1697547 bytes/sec) Router#request platform software package verify rp 1 file stby-bootflash:asr1000rp2-*03.08.01*.pkg mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction ---
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
204
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting mdr compatibility verification --Finished mdr compatibility verification SUCCESS: Software is ISSU MDR compatible. Router# request platform software package install rp 1 file stby-bootflash:asr1000rp2-*03.08.01*.pkg force --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting local lock acquisition on R1 --Finished local lock acquisition on R1 --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
205
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
--- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg Removed asr1000rp2-espbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg New files list: Added asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg Added asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# hw-module slot r1 reload Proceed with reload of module? [confirm] Router# *Mar 15 19:33:59.952: %IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Mar 15 19:34:00.005: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Mar 15 19:34:00.005: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
206
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
*Mar 15 19:34:00.005: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Mar 15 19:34:01.770: %RF-5-RF_RELOAD: Peer reload. Reason: EHSA standby down *Mar 15 19:34:01.780: % Redundancy mode change to SSO *Mar 15 19:37:25.794: %IOSXE_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Mar 15 19:37:34.005: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Mar 15 19:37:34.005: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Mar 15 19:37:36.976: %REDUNDANCY-3-IPC: IOS versions do not match. *Mar 15 19:38:45.751: %NBAR_HA-5-NBAR_INFO: NBAR sync DONE! *Mar 15 19:38:46.165: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Mar 15 19:38:47.165: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# Router# Router#request platform software package install rp 0 file bootflash:asr1000rp2-{sipbase,sipspa}*03.08.01*pkg mdr --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
207
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting mdr compatibility verification --Finished mdr compatibility verification --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg New files list: Added asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software *Mar 15 19:42:48.675: %MDR-5-CARD_RESTART: R0/0: card_reset: Minimal Disruptive Restart SIP0 to acquire provisioned software Applying final IPC and database definitions *Mar 15 19:42:58.508: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: Restart *Mar 15 19:42:58.514: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: Restart *Mar 15 19:42:58.515: %CMCC-5-SPA_MDR_INIT: SIP0: cmcc: Restart Generating software version information Notifying running software of updates SPA0 initiated Minimal Disruptive SPA1 initiated Minimal Disruptive SPA2 initiated Minimal Disruptive
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
208
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Mar 15 19:43:47.031: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Mar 15 19:43:50.504: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0 *Mar 15 19:43:50.849: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1 *Mar 15 19:43:51.133: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Mar 15 19:43:58.338: %LINK-3-UPDOWN: SIP0/0: Interface EOBC0/1, changed state to up *Mar 15 19:44:02.678: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/0 *Mar 15 19:44:02.472: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA0 completed Minimal Disruptive Restart *Mar 15 19:44:02.642: %LINK-3-UPDOWN: SIP0/1: Interface EOBC0/1, changed state to up *Mar 15 19:44:03.451: %TRANSCEIVER-6-INSERTED: SIP0/1: transceiver module inserted in GigabitEthernet0/1/0 *Mar 15 19:44:03.883: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/1 *Mar 15 19:44:03.678: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA1 completed Minimal Disruptive Restart *Mar 15 19:44:04.452: %LINK-3-UPDOWN: SIP0/0: Interface GigabitEthernet0/0/0, changed state to up *Mar 15 19:44:07.327: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up *Mar 15 19:44:10.822: %SPA_OIR-6-ONLINECARD: SPA (SPA-8X1GE-V2) online in subslot 0/2 *Mar 15 19:44:10.619: %CMCC-5-SPA_MDR_DONE: SIP0: cmcc: SPA2 completed Minimal Disruptive Restart Router# Router# request platform software package install rp 0 file bootflash:asr1000rp2-esp*03.08.01*pkg slot 1 --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
209
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING:
WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting list of software package changes --No old package files removed New files list: Added asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP1 Applying final IPC and database definitions *Mar 15 19:47:21.342: %IOSXE_OIR-6-OFFLINECARD: Card (fp) offline in slot F1 software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Generating
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
210
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Mar 15 19:49:17.581: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:49:17.908: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:49:19.334: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F1 *Mar 15 19:49:23.162: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image /tmp/sw/fp/1/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:49:23.380: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization complete *Mar 15 19:49:23.511: %IOSXE-6-PLATFORM: F1: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER Router# Router#request platform software package install rp 0 file bootflash:asr1000rp2-esp*03.08.01*.pkg slot 0 --- Starting local lock acquisition on R0 --Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid Software sets are identified as compatible Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
211
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Finished compatibility testing --- Starting impact testing --Checking operational impact of change Finished impact testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-espbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg No new package files added Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --Finished analysis of software changes --- Starting update running software --Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting ESP0 Applying final IPC and database definitions *Mar 15 19:53:01.267: %IOSXE_OIR-6-OFFLINECARD: Card (fp) offline in slot F0 software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Router# *Mar 15 19:54:54.423: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:54:54.751: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:54:56.877: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0 *Mar 15 19:54:59.998: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /tmp/sw/fp/0/0/fpx86/mount/usr/cpp/bin/qfp-ucode-esp40 *Mar 15 19:55:00.217: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete *Mar 15 19:55:00.347: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER Router# Router# request platform software package install rp 0 file bootflash:asr1000rp2-*03.08.01*.pkg force --- Starting local lock acquisition on R0 --Generating
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
212
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Finished local lock acquisition on R0 --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting image file verification --Checking image file names Locating image files and validating name syntax Found asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Found asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg Found asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg Verifying image file locations Inspecting image file types WARNING: In-service installation of IOSD package WARNING: requires software redundancy on target RP WARNING: or on-reboot parameter WARNING: Automatically setting the on-reboot flag WARNING: In-service installation of RP Base package WARNING: requires software reboot of target RP Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --Determining whether candidate package set is compatible Determining whether installation is valid Determining whether installation is valid ... skipped Verifying image type compatibility Checking IPC compatibility for candidate software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking infrastructure compatibility with running software ... skipped Checking package specific compatibility Finished compatibility testing --- Starting list of software package changes --Old files list: Removed asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg Removed asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg New files list:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
213
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Added asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg Added asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg Finished list of software package changes --- Starting commit of software changes --Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes SUCCESS: Software provisioned. New software will load on reboot.
Router# Router#show version r0 provisioned Package: Provisioning File, version: n/a, status: active File: bootflash:packages.conf, on: RP0 Built: n/a, by: n/a File SHA1 checksum: 2009d5b2f30812a4d743a75386a388710d08d60e Package: rpbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg, on: RP0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: e3cc362353e89c567f6401534abac8aa7f563131 Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP0/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP0/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg, on: RP1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: e3cc362353e89c567f6401534abac8aa7f563131 Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
214
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP1/0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: rpcontrol, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 13ad6ed98884c45fb3fad012baa5ed9cdb6188b3 Package: rpios-adventerprisek9, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.14, by: mcpre File SHA1 checksum: 930fd8616910c930b8f2c6a7e5cd84056633378e Package: rpaccess, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg, on: RP1/1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 44560f45b13a136f7223a3dfde8606c4b3e9816e Package: espbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg, on: ESP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 857b318967cefc17c1af026467b5b4345c8e208a Package: espx86base, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP0 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: espbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg, on: ESP1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 857b318967cefc17c1af026467b5b4345c8e208a Package: espx86base, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg, on: ESP1 Built: 2013-02-08_14.10, by: mcpre File SHA1 checksum: 89c8197e5ff8c1c780db3d5f709691dbe329dcbf Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
215
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP0/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP0/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP0/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP0/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP0/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP1/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP1/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
216
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP1/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP1/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP1/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP2/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP2/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP2/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP2/3 Built: 2013-02-08_12.40, by: mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
217
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP2/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP3/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP3/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP3/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP3/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP3/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP4 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP4
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
218
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP4/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP4/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP4/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP4/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP4/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg, on: SIP5 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 8f3291686d718fbbb702765004e7193ea20087ae Package: elcbase, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg, on: SIP5 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 7a9e6dce8afb6d8473d97209d0fe4543e17917d0 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP5/0 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
219
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP5/1 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP5/2 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81 Package: sipspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg, on: SIP5/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: ae97a24e2f579ab16768a37f69768d717fd467d3 Package: elcspa, version: 03.08.01.S.153-1.S1, status: n/a File: bootflash:asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg, on: SIP5/3 Built: 2013-02-08_12.40, by: mcpre File SHA1 checksum: 613506735b9b536372359dc7b7d94e5004918e81
Router#redundancy force-switchover Proceed with switchover to standby RP? [confirm] Manual Swact = enabled <output removed for brevity> Router# request platform software package clean Cleaning up unnecessary package files No path specified, will use booted path bootflash:packages.conf Cleaning bootflash: Scanning boot directory for packages ... done. Preparing packages list to delete ... asr1000rp2-elcbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-elcspa.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-espbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-espx86base.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpaccess.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpcontrol.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-rpios-adventerprisek9.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-sipbase.03.08.01.S.153-1.S1.pkg File is in use, will not delete. asr1000rp2-sipspa.03.08.01.S.153-1.S1.pkg File is in use, will not delete. packages.conf File is in use, will not delete.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
220
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Using ISSU to Upgrade the SubPackages in a Dual Route Processor Configuration with MDR
Files that will be deleted: asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg asr1000rp2-espbase.03.08.00.S.153-1.S.pkg asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg asr1000rp2-packages-adventerprisek9.03.08.00.S.153-1.S.conf asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg packages.conf.00Do you want to proceed? [confirm]y Deleting file bootflash:asr1000rp2-elcbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-elcspa.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-espbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-espx86base.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-packages-adventerprisek9.03.08.00.S.153-1.S.conf ... done. Deleting file bootflash:asr1000rp2-rpaccess.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpcontrol.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-rpios-adventerprisek9.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-sipbase.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:asr1000rp2-sipspa.03.08.00.S.153-1.S.pkg ... done. Deleting file bootflash:packages.conf.00- ... done. SUCCESS: Files deleted. Router#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
221
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Additional References
Additional References
The following sections provide references related to the Software Upgrade Process feature.
Related Documents
Related Topic Cisco IOS XE commands Performing an In Service Software Upgrade Title Cisco IOS Master Commands List, All Releases High Availability Configuration Guide, Cisco IOS XE Release 3S
Standards
Standard Title No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
RFCs
RFC No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature. Title
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
222
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Additional References
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
223
Software Upgrade Processes Supported by Cisco ASR 1000 Series Aggregation Services Routers Feature Information for Software Upgrade Process
Note
Table 13 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.
Table 13 Feature Information for Software Upgrade Process
Feature Information This feature was introduced. Added support for the following GigabitEthernet SPAs to the Minimal Disruptive Restart (MDR) feature on Cisco ASR 1000 Series Router with SIP40: -SPA-2X1GE-V2 -SPA-5X1GE-V2 -SPA-8X1GE-V2 -SPA-10X1GE-V2 -SPA-1X10GE-L-V2
This feature was introduced. Cisco ASR 1000 Series Routers support the following software upgrade procedures:
In Service Software Upgrades (ISSU) for redundant platforms Upgrade process with service impact for nonredundant platforms.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2012 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
224
Contents
This section discusses various aspects of High Availability on the Cisco ASR 1000 Series Routers and contains the following sections:
Hardware Redundancy Overview on the Cisco ASR 1000 Series Routers, page 2
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
High Availability Overview Hardware Redundancy Overview on the Cisco ASR 1000 Series Routers
Software Redundancy on the Cisco ASR 1000 Series Routers, page 4 Route Processor Redundancy, page 6 Stateful Switchover, page 7 IPsec Failover, page 8 Bidirectional Forwarding Detection, page 8
Allowing two Route Processors (RPs) in the same Cisco ASR 1000 Series Router Allowing two Enhanced Services Processors (ESPs) in the same Cisco ASR 1000 Series Router SPA interface processors (SIPs)A SIP must be reloaded, and traffic briefly interrupted, for a SIP upgrade to complete. Shared port adapters (SPAs)A SPA must be reloaded, which will briefly interrupt traffic to that SPA, for a SPA software subpackage update to complete. A failover optionIf a processor fails, the standby processor immediately becomes the active processor with little or no delay. The failover happens completely within the same router, so a second standby router is not needed. No downtime upgradesUsing features like ISSU, a software upgrade can be handled on the standby processor while the active processor continues normal operation.
Hardware redundancy on the Cisco ASR 1000 Series Routers gives users the following benefits:
Hardware redundancy is available on the Cisco ASR 1006 Router only at this time. provides a hardware redundancy overview.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
High Availability Overview Hardware Redundancy Overview on the Cisco ASR 1000 Series Routers
Table 14
Support for Dual Hardware Configuration on Cisco ASR 1006 Router Failover Behavior Yes If an active ESP experiences a hardware or software event that makes it unable to forward traffic (such as a hardware failure, an OIR, or a manual switch) and a standby ESP is configured, the standby ESP becomes the active ESP with the possibility of a minor interruption (less than 200 ms). If an active RP experiences an event that makes it unable to forward traffic (such as a hardware failure, a software failure, an OIR, or a manual switch) and a standby RP is configured, the standby RP immediately becomes the active RP. No standby configurations are available for SPAs. If a SPA fails, that particular SPA is down and unable to forward traffic. In the event of a SPA shutdown, all other SIPs and SPAs on the router continue to be fully operational.
Route Processor
No
No
No
Yes
SPA
No
No
No
No
SIP
No
No
No
No
No standby configurations are available for SIPs. If a SIP fails, all SPAs in that SIP are down and unable to forward traffic. In the event of a SIP shutdown, all other SIPs and SPAs on the router continue to be fully operational.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
High Availability Overview Software Redundancy on the Cisco ASR 1000 Series Routers
Software Redundancy Overview, page 4 Second IOS Process on a Cisco ASR 1002 or 1004 Router, page 5 SSO-Aware Protocol and Applications, page 7
Router Cisco ASR 1001 Router1 Cisco ASR 1002 Router Cisco ASR 1004 Router Cisco ASR 1006 Router
Support for a Support for Two IOS Second IOS Processes on Same Process on Standby Route Processor Route Processor Explanation Yes N/A The Cisco ASR 1001 Router only supports one RP, so dual IOS processes run on the lone RP. The Cisco ASR 1002 Router only supports one RP, so dual IOS processes run on the lone RP. The Cisco ASR 1004 Router only supports one RP, so dual IOS processes run on the lone RP. The Cisco ASR 1006 Router supports a second Route Processor, so the second IOS process can only run on the standby Route Processor.
Yes
N/A
Yes
N/A
No
Yes
1. If a critical process, such as the ESP or the SIP fails on the Cisco ASR 1001 Router, then the entire chassis reloads.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
High Availability Overview Software Redundancy on the Cisco ASR 1000 Series Routers
ISSU cannot be used to upgrade consolidated packages on Cisco ASR 1002 or 1004 Routers, and only a few subpackages can be upgraded individually using ISSU through the use of dual IOS processes on the same Route Processor. See the Route Processor Redundancy section on page 6 for more information on which subpackages can be upgraded using ISSU in a dual RP setup.
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
redundancy
Example:
Router(config)# redundancy
Step 4
mode SSO
Example:
Router(config)# mode SSO
Configures SSO. When this command is entered, the redundant supervisor engine is reloaded and begins to work in SSO mode. Exits configuration mode and returns to global configuration mode.
Step 5
exit
Example:
Router(config)# exit Router #
Step 6
reload
Example:
Router # reload
Reloads IOS.
Example
Router# configure terminal Router(config)# redundancy Router(config)# mode SSO Router(config)# exit Router# reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
On the Cisco ASR 1000 Series Router, RPR can also be used to enable a second IOS process on a single RP for a Cisco ASR 1002 or 1004 Router. See the Second IOS Process on a Cisco ASR 1002 or 1004 Router section on page 5 for additional information on the second IOS process. For the Cisco ASR 1000 Series Routers, RPR introduces the following functionality:
Startup configuration synchronization between the active and standby RP or IOS process. It is important to note, however, that changes in the running configuration are not synchronized using RPR. Warm ReloadThe Warm Reload feature allows users to reload their routers without reading images from storage; that is, the router reboots by restoring the read-write data from a previously saved copy in the RAM and by starting execution without either copying the software from flash to RAM or self-decompression of the image.
It is important to note that in most cases, Stateful Switchover (SSO) requires less downtime for switchover and upgrades than RPR. RPR should only be used when there is a compelling reason to not use SSO. It is important to note RPR is supported on the Cisco ASR 1000 Series Routers while RPR+ is not.
Stateful Switchover
The Stateful Switchover (SSO) feature takes advantage of processor redundancy by establishing one of the processors as the active processor while the other RP is designated as the standby processor, and then synchronizing critical state information between them. Following an initial synchronization between the two processors, SSO dynamically maintains RP state information between the dual processors. Stateful Switchover is particularly useful in conjunction with Nonstop Forwarding. SSO allows the dual processors to maintain state at all times, and Nonstop Forwarding lets a switchover happen seamlessly when a switchover occurs. On the Cisco ASR 1000 Series Router, SSO can also be used to enable a second IOS process on a single RP for a Cisco ASR 1002 or 1004 Router. See the Second IOS Process on a Cisco ASR 1002 or 1004 Router section on page 5 for additional information on the second IOS process. It is important to note that in most cases, SSO requires less downtime for switchover and upgrades than RPR. RPR should only be used when there is a compelling reason to not use SSO. For additional information on NSF/SSO, see the Cisco Nonstop Forwarding document.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
IPsec Failover
IPSec failover is a feature that increases the total uptime (or availability) of a customer's IPSec network. Traditionally, this is accomplished by employing a redundant (standby) router in addition to the original (active) router. If the active router becomes unavailable for any reason, the standby router takes over the processing of IKE and IPSec. IPSec failover falls into two categories: stateless failover and stateful failover. The IPsec on the Cisco ASR 1000 Series Router supports only stateless failover. Stateless failover uses protocols such as the Hot Standby Router Protocol (HSRP) to provide primary to secondary cutover and also allows the active and standby VPN gateways to share a common virtual IP address.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Additional References
Related Documents
Related Topic Bidirectional Forwarding Detection High Availability Configurations Software Upgrade Process Configurations Cisco IOS commands Document Title IP Routing BFD Configuration Guide, Cisco IOS XE Release 3S High Availability Configuration Guide, Cisco IOS XE Release 3S Software Upgrade Process Configuration Guide Cisco IOS Master Commands List, All Releases
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Note
Table 17 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 17
Feature Information In Cisco IOS XE Release 2.1S, this feature was introduced on the Cisco ASR 1000 Series Router.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Contents
This guide provides information about the following topics:
PPP Sessions and L2TP Tunnel Scaling, page 2 ISG Scaling, page 3 Layer 4 Redirect Scaling, page 4 Configuring the Cisco ASR 1000 Series Router for High Scalability, page 4 Using the cisco-avpair="lcp:interface-config" RADIUS Attribute, page 7 Walk-by User Support for PWLAN in ISG, page 9
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Broadband Scalability and Performance PPP Sessions and L2TP Tunnel Scaling
Chassis 1001 1002 1004, 1006 1004, 1006 1004, 1006, 1013
1. 32000 session scaling with RP2 and ESP-40G is fully supported without any additional restrictions. For restrictions on 48000 and 64000 see the Restrictions for PPP Sessions and L2TP Tunnel Scaling section on page 2.
Table 19 lists the virtual circuit limits for ASR 1000 ATM SPAs, effective from Cisco IOS XE Release 3.5.
Table 19 ASR 1000 ATM Virtual Circuit (VC) Limits
ASR1000-SIP10 SPA/SIP SPA-1XOC12-ATM-V2 SPA-1XOC3-ATM-V2 SPA-3XOC3-ATM-V2 ASR1000-SIP10 Number of VCs 4000 VCs per Port, 4000 VCs per SPA 4000 VCs per Port, 4000 VCs per SPA 3000 VCs per Port, 9000 VCs per SPA 24000 VCs per SIP
ASR1000-SIP40 SPA/SIP SPA-1XOC12-ATM-V2 SPA-1XOC3-ATM-V2 SPA-3XOC3-ATM-V2 ASR1000-SIP40 Number of VCs 4000 VCs per Port, 4000 VCs per SPA 4000 VCs per Port, 4000 VCs per SPA 4000 VCs per Port, 12000 VCs per SPA 32000 VCs per SIP
To achieve maximum scaling for the 1001, 1002, and 1004 chassis, we recommend software redundancy be disabled for broadband applications, and only hardware redundancy be configured. Restrictions on 48000 session scaling with RP2 and ESP-40G include:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Intelligent Services Gateway (ISG) Services are not supported Point-to-Point Protocol over ATM (PPPoA) and Point-to-Point Protocol over Ethernet
Note
If any of the listed restrictions is not met, the router scales to a maximum of 32000 sessions only.
Note
If any of the listed restrictions is not met, the router scales to a maximum of 32000 sessions or 48000 sessions only.
Note
If any of the listed restrictions is not met, the router scales to a maximum of 16000 L2TP tunnels.
The RP2 and ESP10 hardware combination is not supported for broadband. RP1 with 2GB of DRAM is not recommended for broadband deployment.
ISG Scaling
The ASR 1000 Series Routers can be deployed as an IP session aggregator. The maximum number of IP sessions that can be supported depends on the hardware combination. Table 20 lists the hardware combination and the maximum number of IP sessions that are supported when used for wireline Broadband applications. The session limits apply to all variety of IP session initiators: DHCP, unclassified Mac address, unclassified IP, and RADIUS proxy..
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 20
Note
Configuring the Cisco ASR 1000 Series Router for High Scalability
The Cisco ASR 1000 Series Routers provide powerful performance and scalability for embedded services. To achieve maximum scaling on the 1001, 1002, and 1004 chassis, IOS software redundancy must be disabled. For more information about restrictions and limitations, see the Restrictions for PPP Sessions and L2TP Tunnel Scaling section on page 2. To ensure high scalability on the Cisco ASR 1000 Series Router, perform the following configuration tasks:
Configuring Call Admission Control, page 5 Control Plane Policing, page 5 VPDN Group Session Limiting, page 6 PPPoE Session Limiting, page 6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Broadband Scalability and Performance Configuring the Cisco ASR 1000 Series Router for High Scalability
Monitoring PPP Sessions Using the SNMP Management Tools, page 6 Configuring the Access Interface Input and Output Hold Queue, page 6 Configuring the keepalive Command, page 6 Scaling the L2TP Tunnel Configurations, page 7
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Broadband Scalability and Performance Configuring the Cisco ASR 1000 Series Router for High Scalability
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Note
For IP sessions, the keepalives are not enabled by default. Enabling keepalives for IP sessions provides the same capability as PPP keepalives except that ICMP or ARP is used to test the presence of subscribers. For more information about Using ARP for Keepalive Messages and Using ICMP for Keepalive Messages, see the feature documentation at: http://www.cisco.com/en/US/docs/ios-xml/ios/isg/configuration/xe-3s/Configuring_ISG_Policies_for_ Session_Maintenance.html
When you configure this command, the router directly queues the L2TP Hello packets and Hello acknowledgements to the L2TP control process. We recommend that you configure this command in all the scaled LAC and LNS L2TP tunnel configurations. If you do not configure the vpdn ip udp ignore checksum command, the L2TP software sends the packets to UDP to validate the checksum. When too many packets are queued to the IP input process, the router starts Selective Packet Discard (SPD) mechanism that causes IP packets to be dropped.
Note
Head-of-the-line blocking of the IP input process might occur in other nonL2TP configurations. A flush occurring on an input interface indicates that the SPD mechanism is discarding packets.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
You should specify only one ip:vrf-id and one ip:ip-unnumbered value in a user profile. However, if the profile configuration includes multiple values, the Cisco ASR 1000 Series Router applies the value of the last VSA received, and creates a virtual access subinterface. If the profile includes the lcp:interface-config VSA, the router always applies the value of the lcp:interface-config VSA.
Setting the VRF and IP Unnumbered Interface Configurations in Virtual Interface Templates
You can specify one VSA value in a user profile on RADIUS and another value locally in the virtual template interface. The Cisco ASR 1000 Series Router clones the template and then applies the values configured in the profiles it receives from RADIUS, resulting in the removal of any IP configurations when the router applies the profile values.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Broadband Scalability and Performance Walk-by User Support for PWLAN in ISG
The following example shows how to redefine the Loopback 0 interface using the ip:ip-unnumbered VSA.
Change: Cisco:Cisco-Avpair = lcp:interface-config=ip unnumbered Loopback 0 To: Cisco:Cisco-Avpair = ip:ip-unnumbered=Loopback 0
On the ASR 1000 Series router, the Layer 4 Redirect (L4R) feature supports a maximum of 16 translation entries per walk-by session. For more information on the limit for the total number of translations on the system, see Layer 4 Redirect Scaling, page 4.
Note
For additional platform-independent restrictions pertaining to the walk-by sessions and information on how to configure the Walk-By User Support for PWLAN in ISG feature, refer to the following URL: http://www.cisco.com/en/US/docs/ios-xml/ios/isg/configuration/xe-3s/isg-wlkby-supp.html
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Broadband Scalability and Performance Walk-by User Support for PWLAN in ISG
The scale numbers provided in the Table 22 assume the following reference configuration:
Walk-by users: A maximum of three traffic classes on the default session. Authenticated users: A maximum of three traffic classes per user, with accounting on each traffic class and L4R on a single traffic class.
Any deviation from the conditions mentioned above may result in different scale numbers. The scale limits and the hardware combinations listed in the next table requires a maximum available RP memory size (16GB DRAM).
Table 22 ISG Scaling Numbers and Supported Hardware
Calls Per Second2 Hardware RP2/ESP40 RP2/ESP100 ASR1002-X ASR1001 Walk-by Users1 128 K 224 K 128 K 16 K Authenticated Users1 48 K 48 K 32 K 8K Walk-by Users 135 135 135 135 Authenticated Users 15 15 15 15
1. For a redundant system, after a route processor (RP) switchover, the existing configuration in a forwarding processor (FP) takes some time to be cleaned up while new configuration (for walk-by users) is applied at a faster rate. In this scenario, if the system operates at the maximum scale before the switchover, the system might exceed the resource limit. Therefore, it is advisable to run a redundant system at a reduced scale. 2. The calls-per-second rates mentioned in the Table 22 are the target-sustained rates. However, after events such as failover or reload, the rates might exceed these numbers for some period before falling back to the sustained values.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Additional References
Related Documents
Related Topic Control Plane Policing VPDN Group Session Limiting PPPoE session limiting Using ARP for Keepalive Messages and Using ICMP for Keepalive Messages Cisco IOS commands Document Title Quality of Service Solutions Configuration Guide VPDN Configuration Guide, Cisco IOS XE Release 3S Configuring PPP over Ethernet Session Limit Support Feature Guide Intelligent Services Gateway Configuration Guide Cisco IOS XE Release 3S Cisco IOS Master Commands List, All Releases
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website provides online http://www.cisco.com/cisco/web/support/index.html resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Broadband Scalability and Performance Feature Information for Broadband Scalability and Performance
Note
Table 23 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 23
Feature Name High Availability Overview Walk-by User Support for PWLAN in ISG
Feature Information In Cisco IOS XE Release 2.1S, this feature was introduced on the Cisco ASR 1000 Series Router. In Cisco IOS XE Release 3.7S, this feature was introduced on the Cisco ASR 1000 Series Router.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Contents
Prerequisites for Cisco License Call Home, page 2 Restrictions for Cisco License Call Home, page 2 Informatio n About Cisco License Call Homes, page 2 How to Configure Cisco License Call Home, page 3 Configuration Examples for Cisco License Call Home, page 6 Additional References, page 9 Feature Information for Cisco License Call Home, page 10
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Configuring Cisco License Call Home Prerequisites for Cisco License Call Home
You must obtain the device certificate from the Cisco licensing infrastructure before starting. You must have a CCO user login account.
The router or switch must have an Internet connection and use HTTPS to connect to the Cisco licensing infrastructure. To set up a secure HTTP connection, see the HTTP 1.1 Web Server and Client chapter in the HTTP Services Configuration Guide: http://www.cisco.com/en/US/docs/ios-xml/ios/https/configuration/xe-3s/https-xe-3s-book.html Only certain platforms support the Cisco License Call Home feature, and these devices must be running a Cisco IOS crypto K9 image. For information about platform support, see the Feature Information for Cisco License Call Home section on page 10.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home How to Configure Cisco License Call Home
Figure 1 shows how the Cisco License Call Home feature interfaces to the Cisco licensing back-end system. The architecture shown in Figure 1 allows the use of the License Call Home EXEC commands to communicate with the Cisco licensing infrastructure and to perform administrative license operations.
Figure 1 Cisco License Call Home Interface
License Call Home transport for XML requests and to create SWIFT sessions
HTTPS
INTERNET
Device
Licensing infrastructure
The Cisco License Call Home feature works as a client-server model with each transaction completed as a separate connection to the Cisco licensing infrastructure. The Cisco License Call Home feature displays prompts to obtain required information and then connects to the Cisco licensing back end to interact with the Cisco licensing infrastructure. A Cisco License Call Home EXEC command initiates a request, and the Cisco licensing infrastructure provides the response. The processes designed into the Cisco License Call Home architecture manage the transport of information that provides the URL required to connect to the Cisco licensing infrastructure over the Internet and to create a session.
Installing Licenses or Upgrading Software by Using Cisco License Call Home, page 3 (required) Rehosting a License by Using Cisco License Call Home, page 4 (optional) Requesting a License Resend by Using Cisco License Call Home, page 5 (optional)
SUMMARY STEPS
1. 2.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
204163
License administrative operations install, revoke, provide UDI and device credential
Configuring Cisco License Call Home How to Configure Cisco License Call Home
3. 4. 5.
show license call-home pak pak-id license call-home install pak pak-id show license feature
DETAILED STEPS
Command or Action
Step 1
Purpose The PAK is provided to you when you order or purchase the right to use a feature set for a particular platform. The PAK serves as a receipt and is used as part of the process to obtain a license. Enables privileged EXEC mode.
Step 2
enable
Example:
Router> enable
Step 3
Displays the stock keeping unit (SKU) list and features available for the PAK provided.
Example:
Router# show license call-home pak 3XPXR9E7D30
Step 4
Example:
Router# license call-home install pak 3XPXR9E7D30
Step 5
Example:
Router# show license feature
SUMMARY STEPS
1. 2. 3. 4.
enable license call-home revoke udi target-udi output-of-rehosted-license-url show license detail (Optional) license install stored-location-url
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home How to Configure Cisco License Call Home
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
Example:
Router# license call-home revoke udi AS54XM-AC-RPS:JAE0948QT6R flash:licensetargetudi.xml
Revokes and transfers a license by using source and target UDIs. Sends the rehost ticket to the Cisco licensing infrastructure with the target UDI, converts it to a license file, and stores it in the URL specified.
Select from multiple SKUs for rehosting when you are prompted, and supply information when required.
Step 3
Example:
Router# show license detail
Step 4
For details, see the Installing and Upgrading Licenses in the Configuring the Cisco IOS Software Activation Feature module.
SUMMARY STEPS
1. 2. 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home Configuration Examples for Cisco License Call Home
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
Obtains all licenses this device owns and stores them in the specified location.
Example:
Router# license call-home resend flash:licenseresend.lic
Step 3
For details, see the Installing and Upgrading Licenses in the Configuring the Cisco IOS Software Activation Feature module.
Example: Installing Licenses or Upgrading Software by Using Cisco License Call Home, page 6 Example: Rehosting a License by Using Cisco License Call Home, page 7 Example: Requesting a License Resend by Using Cisco License Call Home, page 8
Example: Installing Licenses or Upgrading Software by Using Cisco License Call Home
The following example shows how to use the license call-home install pak command to install a license by using the Cisco License Call Home feature. The command also displays prompts for mandatory information. The show license feature command is used to verify the installation.
Router# license call-home install pak 3XPXR9E7D30 CCO CCO Pak Pak User name: User1 password : ************ Number : 3XPXR9E7D30 Fulfillment type: SINGLE 1. SKU Name SKU Type Description Ordered Qty Available Qty Feature List Feature name: Platform Supported : : : : : : Gatekeeper Product Gatekeeper 1 1 gatekeeper Count: Uncounted : N/A 5400 5350 2800 3800
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home Configuration Examples for Cisco License Call Home
Please enter the user's detail: First Name : First-name Last Name : Last-name Title : Software Engineer Company Name : Cisco Systems Address1 : 510 McCarthy Blvd. Address2 [Optional]: City : Milpitas State : CA Province [Optional]: Zipcode : 95134 Country : USA Phone : 408 526-4000 Fax [Optional]: Email : User1@cisco.com Installing...Feature:gatekeeper...Successful Router# show license feature Feature name gsmamrnb-codec-pack Router# Enforcement yes Evaluation yes Subscription no Enabled no
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home Configuration Examples for Cisco License Call Home
2800 3800 4. SKU Name : GSMAMRNB SKU Type : Product Description : Transfer this feature set Ordered Qty : 1 Available Qty : 1 Feature List : Feature name: gsmamrnb-codec-pac Count: Uncounted Platform Supported : 5400 5350 5. All of the above Please select the sku number you want to revoke : 4 Retrieving the permission ticket from swift .............
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Additional References
Related Documents
Related Topic Cisco License Manager application Cisco IOS XE Software Activation conceptual overview Cisco IOS Software Activation Command Reference Cisco IOS commands Integrated Services Routers licensing Document Title User Guide for Cisco License Manager Software Activation Configuration Guide, Cisco IOS XE Release 3S Cisco IOS Software Activation Command Reference Cisco IOS Master Commands List, All Releases Software Activation on Cisco Integrated Services Routers
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring Cisco License Call Home Feature Information for Cisco License Call Home
Note
Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 1
Feature Name
Releases
Feature Information
Cisco License Call Home Cisco IOS The Cisco License Call Home feature provides a robust set of commands that XE Release communicate with the Cisco licensing infrastructure, makes connections and data 3.6S transfers, and provides interactive prompts to help you install and maintain software licenses. In Cisco IOS XE Release 3.6S, this feature was introduced on the Cisco ASR 1000 Series Router. The following commands were introduced or modified by this feature: license call-home install, license call-home resend, license call-home revoke, license call-home url, show license call-home.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
The Call Home feature provides e-mail-based and web-based notification of critical system events. A versatile range of message formats are available for optimal compatibility with pager services, standard e-mail, or XML-based automated parsing applications. Common uses of this feature may include direct paging of a network support engineer, e-mail notification to a Network Operations Center, XML delivery to a support website, and utilization of Cisco Smart Call Home services for direct case generation with the Cisco Systems Technical Assistance Center (TAC). This document describes how to configure the Call Home feature on Cisco ASR 1000 Series Aggregation Services Routers beginning with Cisco IOS XE Release 2.6.
Finding Feature Information in This Module
Your Cisco IOS software release may not support all of the features documented in this module. To reach links to specific feature documentation in this module and to see a list of the releases in which each feature is supported, use the Feature Information for Call Home section on page 59.
Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Contents
This guide includes the following sections:
Information About Call Home, page 2 Prerequisites for Call Home, page 3 How to Configure Call Home, page 4 How To Configure Call Home to Support the Smart Call Home Service, page 27 Displaying Call Home Configuration Information, page 34 Default Settings, page 39 Alert Group Trigger Events and Commands, page 40
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Message Contents, page 42 Additional References, page 57 Feature Information for Call Home, page 59
Benefits of Using Call Home, page 2 How to Obtain Smart Call Home Service, page 3
Markup Language (AML) document type definitions (DTDs). The XML format enables communication with the Cisco Smart Call Home server.
Multiple concurrent message destinations. Multiple message categories, including configuration, diagnostics, environmental conditions, inventory, and syslog events. Filtering of messages by severity and pattern matching. Scheduling of periodic message sending.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Analysis of Call Home messages from your device, and where supported, automatic Service Request generation routed to the appropriate TAC team, including detailed diagnostic information to speed problem resolution. Continuous device health monitoring. Analysis of Call Home messages from your device. Secure message transport directly from your device or through a downloadable Transport Gateway (TG) aggregation point. You can use a TG aggregation point in cases requiring support for multiple devices or in cases where security requirements mandate that your devices may not be connected directly to the Internet. Web-based access to Call Home messages and recommendations, inventory, and configuration information for all Call Home devices. Provides access to associated Field Notices, Security Advisories, and End-of-Life Information. SMARTnet contract number for your router. Your e-mail address Your Cisco.com ID
For information about how to configure Call Home to work with the Smart Call Home service, see the How To Configure Call Home to Support the Smart Call Home Service section on page 27. For detailed information on Smart Call Home, see the Smart Call Home page at: http://www.cisco.com/en/US/products/ps7334/serv_home.html
Obtain e-mail, phone, and street address information for the Call Home contact to be configured so that the receiver can determine the origin of messages received. Identify the name or IPv4 address of a primary Simple Mail Transfer Protocol (SMTP) server and any backup servers, if using e-mail message delivery. Configure a trustpoint certificate authority (CA) if using secure HTTP (HTTPS) message delivery. For example, this procedure is required if you are using the HTTPS server for Cisco Smart Call Home Service in the CiscoTAC-1 profile for Call Home. Verify IP connectivity from the router to the e-mail server(s) or the destination HTTP server.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
If Cisco Smart Call Home is used, verify an active service contract exists for the device being configured.
Configuring the Management Interface VRF, page 4 (required) Configuring a Destination Profile, page 5 (required) Subscribing to Alert Groups, page 17 (required) Configuring Contact Information, page 21 (required) Configuring the Number of Call Home Messages Sent Per Minute, page 23 (optional) Enabling and Disabling Call Home, page 23 (required) Sending Call Home Communications Manually, page 24 (optional)
SUMMARY STEPS
1. 2. 3. 4.
configure terminal interface GigabitEthernet 0 vrf forwarding Mgmt-intf ip address ip-address mask [secondary [vrf vrf-name]] or ipv6 address {X:X:X:X::X link-local | X:X:X:X::X/prefix [anycast | eui-64] | autoconfig [default]}
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
interface GigabitEthernet 0
(Required) Specifies the Gigabit Ethernet Management interface on the Cisco ASR 1000 Series Router.
Example:
Router(config)# interface GigabitEthernet0
Step 3
Example:
Router(config-if)# vrf forwarding Mgmt-intf
(Required) Associates the Mgmt-intf VRF with the Gigabit Ethernet Management interface. This command is configured by default. (Required) Specifies the IPv4 or IPv6 addressing for the interface.
Step 4
or
ipv6 address {X:X:X:X::X link-local | X:X:X:X::X/prefix [anycast | eui-64] | autoconfig [default]}
Example:
Router(config-if)# ip address 10.10.10.10 0.0.0.0
What To Do Next
To find out more about the Gigabit Ethernet Management interface on the Cisco ASR 1000 Series Routers or perform additional related configuration tasks on the management interface, see the Using the Management Ethernet Interface section on page 1 .
Note
The Call Home feature provides a predefined profile named CiscoTAC-1 that is inactive by default. The CiscoTAC-1 profile is intended for use with the Smart Call Home service, which requires certain additional configuration steps to enable the service with the Call Home feature. For more information about this profile, see the Using the Predefined CiscoTAC-1 Destination Profile section on page 17.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Profile nameA string that uniquely identifies each user-defined destination profile. The profile name is limited to 31 characters and is not case-sensitive. You cannot use all as a profile name. Transport methodThe transport mechanism, either e-mail or HTTP (including HTTPS), for delivery of alerts.
For user-defined destination profiles, e-mail is the default, and you can enable one or both
Destination addressThe actual address related to the transport method to which the alert should be sent. Message formattingThe message format used for sending the alert. The format options for a user-defined destination profile are long-text, short-text, or XML. The default is XML. For the predefined Cisco TAC profile, only XML is allowed. If you use the Cisco Smart Call Home service, the destination profile must use the XML message format. Message sizeThe maximum destination message size. The valid range is 50 to 3,145,728 bytes and the default is 3,145,728 bytes. Configuring a Destination Profile to Send Email Messages, page 6 Configuring a Destination Profile to Send HTTP Messages, page 10 Working With Destination Profiles, page 14
Configuring the Mail Server, page 6 Associating the Management Interface VRF With Call Home, page 7 Configuring a Destination Profile for E-mail, page 8 Configuring Other Email Options, page 10
Backup e-mail servers can be defined by repeating the mail-server command using different priority numbers. The mail-server priority number parameter can be configured from 1 to 100. The server with the highest priority (lowest priority number) is tried first.
SUMMARY STEPS
1. 2.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
3.
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
Specifies an e-mail server and its relative priority among configured e-mail servers, where:
Example:
Router(cfg-call-home)# mail-server stmp.example.com priority 1
ipv4-addressSpecifies the IPv4 address of the mail server. nameSpecifies the mail servers fully qualified domain name (FQDN) of 64 characters or less. numberAssigns a number between 1 (highest priority) and 100 (lowest priority).
Example:
The following example shows the configuration of a primary mail server (named smtp.example.com) and secondary mail server at IP address 192.168.0.1:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# call-home Router(cfg-call-home)# mail-server smtp.example.com priority 1 Router(cfg-call-home)# mail-server 192.168.0.1 priority 2 Router(cfg-call-home)# exit
Router(config)#
SUMMARY STEPS
1. 2. 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
vrf Mgmt-intf
(Required) Associates the Mgmt-intf VRF for the email transport method using Call Home.
Example:
Router(cfg-call-home)# vrf Mgmt-intf
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
configure terminal call-home profile name destination transport-method email destination address email email-address destination preferred-msg-format {long-text | short-text | xml} destination message-size bytes active exit
10. end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
profile name
Example:
Router(config-call-home)# profile profile1
Enters call home destination profile configuration mode for the specified destination profile name. If the specified destination profile does not exist, it is created. (Optional) Configures the message transport method for email. This is the default.
Step 4
Example:
Router(cfg-call-home-profile)# destination transport-method email
Step 5
(Required) Configures the destination e-mail address to which Call Home messages are sent.
Example:
Router(cfg-call-home-profile)# destination address email myaddress@example.com
Step 6
Example:
Router(cfg-call-home-profile)# destination preferred-msg-format xml
Step 7
Example:
Router(cfg-call-home-profile)# destination message-size 3145728
(Optional) Configures a maximum destination message size (from 50 to 3145728 bytes) for the destination profile. The default is 3145728 bytes.
Step 8
active
(Optional) Enables the destination profile. By default, a user-defined profile is enabled when it is created.
Example:
Router(cfg-call-home-profile)# active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command or Action
Step 9
exit
Purpose Exits call home destination profile configuration mode and returns to call home configuration mode.
Example:
Router(cfg-call-home-profile)# exit
Step 10
end
Example:
Router(cfg-call-home)# end
SUMMARY STEPS
1. 2. 3. 4.
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
Example:
Router(cfg-call-home)# sender from username@example.com
(Optional) Assigns the e-mail address that will appear in the from field in Call Home e-mail messages. If no address is specified, the contact e-mail address is used.
Step 4
(Optional) Assigns the e-mail address that will appear in the reply-to field in Call Home e-mail messages.
Example:
Router(cfg-call-home)# sender reply-to username@example.com
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Configuring the HTTP Source Interface, page 11 Configuring a Destination Profile for HTTP, page 11 Configuring a Trustpoint Certificate Authority, page 14
SUMMARY STEPS
1. 2. 3.
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
Example:
Router(config)# ip http client source-interface gigabitethernet 0
On the Cisco ASR 1000 Series Router, this interface should be the VRF management interface.
Step 3
end
Example:
Router(cfg-call-home)# end
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
configure terminal call-home profile name destination transport-method http destination address http url destination preferred-msg-format {long-text | short-text | xml} destination message-size bytes active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
9.
exit
10. end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
profile name
Example:
Router(config-call-home)# profile test
Enters call home destination profile configuration mode for the specified destination profile. If the specified destination profile does not exist, it is created. Enables the HTTP message transport method.
Step 4
Example:
Router(cfg-call-home-profile)# destination transport-method http
Step 5
Configures the destination URL to which Call Home messages are sent.
Note
Example:
Router(cfg-call-home-profile)# destination address http https://example.url.com
When entering a destination URL, include either http:// or https://, depending on whether the server is a secure server. If the destination is a secure server, you must also configure a trustpoint CA.
Step 6
Example:
Router(cfg-call-home-profile)# destination preferred-msg-format xml
Step 7
(Optional) Configures a maximum destination message size for the destination profile.
Example:
Router(cfg-call-home-profile)# destination message-size 3,145,728
Step 8
active
Example:
Router(cfg-call-home-profile)# active
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Command or Action
Step 9
exit
Purpose Exits call home destination profile configuration mode and returns to call home configuration mode.
Example:
Router(cfg-call-home-profile)# exit
Step 10
end
Example:
Router(cfg-call-home)# end
Activating and Deactivating a Destination Profile, page 14 Copying a Destination Profile, page 15 Renaming a Destination Profile, page 16 Using the Predefined CiscoTAC-1 Destination Profile, page 17
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
profile name
Example:
Router(config-call-home)# profile test
Enters call home destination profile configuration mode for the specified destination profile. If the specified destination profile does not exist, it is created. Enables the destination profile. By default, a new profile is enabled when it is created.
Step 4
active
Example:
Router(cfg-call-home-profile)# active
Step 5
no active
Example:
Router(cfg-call-home-profile)# no active
Step 6
end
Exits call home destination profile configuration mode and returns to privileged EXEC mode.
Example:
Router(cfg-call-home)# end
SUMMARY STEPS
1. 2. 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
Example:
Router(cfg-call-home)# copy profile profile1 profile2
Creates a new destination profile with the same configuration settings as the existing destination profile, where:
source-profileSpecifies the existing name of the profile. target-profileSpecifies a name for the new copy of the profile.
SUMMARY STEPS
1. 2. 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
Example:
Router(cfg-call-home)# rename profile2 testprofile
source-profileSpecifies the existing name of the profile. target-profileSpecifies a new name for the existing profile.
For more information about additional requirements for Configuring the Smart Call Home service, see the How To Configure Call Home to Support the Smart Call Home Service section on page 27.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
The triggering events for each alert group are listed in the Alert Group Trigger Events and Commands section on page 40, and the contents of the alert group messages are listed in the Message Contents section on page 42. You can select one or more alert groups to be received by a destination profile.
Note
A Call Home alert is only sent to destination profiles that have subscribed to the alert group containing that Call Home alert. In addition, the alert group must be enabled.
Periodic Notification
When you subscribe a destination profile to either the Configuration or the Inventory alert group, you can choose to receive the alert group messages asynchronously or periodically at a specified time. The sending period can be one of the following:
DailySpecify the time of day to send, using an hour:minute format hh:mm, with a 24-hour clock (for example, 14:30). WeeklySpecify the day of the week and time of day in the format day hh:mm, where the day of the week is spelled out (for example, monday). MonthlySpecify the numeric date, from 1 to 31, and the time of day, in the format date hh:mm.
Note
When syslog level is changed via IOS CLI, the new value is propagated to non-IOS processes as well, with the result that these processes no longer send syslog messages of lower priority to IOS to process, thus "saving" CPU cycles for IOS Table 1 lists the keywords used to configure the severity, which range from catastrophic (level 9, highest level of urgency) to debugging (level 0, lowest level of urgency). If no severity threshold is configured, the default is debugging (level 0). However, the default is not recommended due to the number of messages that will be triggered.
Note
Call Home severity levels are not the same as system message logging severity levels.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
Table 1
Level 9 8 7 6 5 4 3 2 1 0
Keyword catastrophic disaster fatal critical major minor warning notification normal debugging
Syslog Level N/A N/A Emergency (0) Alert (1) Critical (2) Error (3) Warning (4) Notice (5) Information (6) Debug (7)
Description Network-wide catastrophic failure. Significant network impact. System is unusable. Critical conditions, immediate attention needed. Major conditions. Minor conditions. Warning conditions. Basic notification and informational messages. Possibly independently insignificant. Normal event signifying return to normal state. Debugging messages.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
configure terminal call-home alert-group {all | configuration | environment | inventory | syslog} profile name subscribe-to-alert-group all subscribe-to-alert-group configuration [periodic {daily hh:mm | monthly date hh:mm | weekly day hh:mm}] subscribe-to-alert-group diagnostic [severity {catastrophic | critical | debugging | disaster | fatal | major | minor | normal | notification | warning}] subscribe-to-alert-group environment [severity {catastrophic | critical | debugging | disaster | fatal | major | minor | normal | notification | warning}] subscribe-to-alert-group inventory [periodic {daily hh:mm | monthly date hh:mm | weekly day hh:mm}] major | minor | normal | notification | warning}] [pattern string]
10. subscribe-to-alert-group syslog [severity {catastrophic | critical | debugging | disaster | fatal | 11. exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
Enables the specified alert group. Use the all keyword to enable all alert groups. By default, all alert groups are enabled.
Example:
Router(cfg-call-home)# alert-group all
Step 4
profile name
Enters call home destination profile configuration mode for the specified destination profile.
Example:
Router(cfg-call-home)# profile profile1
Step 5
subscribe-to-alert-group all
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group all
Alternatively, you can also subscribe to alert groups individually by specific type as described in steps 6 through 9.
Step 6
subscribe-to-alert-group configuration [periodic {daily hh:mm | monthly date hh:mm | weekly day hh:mm}]
Subscribes this destination profile to the Configuration alert group, with an optional periodic value.
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group configuration periodic daily 12:00
Step 7
subscribe-to-alert-group diagnostic [severity {catastrophic | critical | debugging | disaster | fatal | major | minor | normal | notification | warning}]
Subscribes this destination profile to the Diagnostic alert group, with an optional severity level.
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group diagnostic severity critical
Step 8
subscribe-to-alert-group environment [severity {catastrophic | critical | debugging | disaster | fatal | major | minor | normal | notification | warning}]
Subscribes this destination profile to the Environment alert group, with an optional severity level.
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group environment severity major
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Command or Action
Step 9
subscribe-to-alert-group inventory [periodic {daily hh:mm | monthly date hh:mm | weekly day hh:mm}]
Purpose Subscribes this destination profile to the Inventory alert group, with an optional periodic value.
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group inventory periodic monthly 1 12:00
Step 10
subscribe-to-alert-group syslog [severity {catastrophic | critical | debugging | disaster | fatal | major | minor | normal | notification | warning}][pattern string]
Example:
Router(cfg-call-home-profile)# subscribe-to-alert-group syslog
Subscribes this destination profile to the Syslog alert group, with an optional severity level. You can specify a pattern to be matched in the syslog message, up to a maximum of five patterns per profile. If the pattern contains spaces, you must enclose it within double quotation marks ( ).
Step 11
exit
Example:
Router(cfg-call-home-profile)# exit
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
configure terminal call-home contact-email-addr email-address phone-number +phone-number street-address street-address customer-id text site-id text contract-id text
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router> configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
contact-email-addr email-address
Assigns the customers e-mail address. Enter up to 200 characters in e-mail address format with no spaces.
Example:
Router(cfg-call-home)# contact-email-addr username@example.com
Step 4
phone-number +phone-number
Example:
Router(cfg-call-home)# phone-number +1-222-333-4444
The number must begin with a plus (+) prefix, and may contain only dashes (-) and numbers. Enter up to 16 characters. If you include spaces, you must enclose your entry within double quotation marks ( ).
Step 5
street-address street-address
Example:
Router(cfg-call-home)# street-address 1234 Any Street, Any city, Any state, 12345
(Optional) Assigns the customers street address where RMA equipment can be shipped. Enter up to 200 characters. If you include spaces, you must enclose your entry within double quotation marks ( ). (Optional) Identifies the customer ID. Enter up to 64 characters. If you include spaces, you must enclose your entry within double quotation marks ( ). (Optional) Identifies the customer site ID. Enter up to 200 characters. If you include spaces, you must enclose your entry within double quotation marks ( ). (Optional) Identifies the customers contract ID for the router. Enter up to 64 characters. If you include spaces, you must enclose your entry within double quotation marks ( ).
Step 6
customer-id text
Example:
Router(cfg-call-home)# customer-id Customer1234
Step 7
site-id text
Example:
Router(cfg-call-home)# site-id Site1ManhattanNY
Step 8
contract-id text
Example:
Router(cfg-call-home)# contract-id Company1234
Example
The following example shows the configuration of contact information:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
Enter configuration commands, one per line. End with CNTL/Z. Router(config)# call-home Router(cfg-call-home)# contact-email-addr username@example.com Router(cfg-call-home)# phone-number +1-222-333-4444 Router(cfg-call-home)# street-address 1234 Any Street, Any city, Any state, 12345 Router(cfg-call-home)# customer-id Customer1234 Router(cfg-call-home)# site-id Site1ManhattanNY Router(cfg-call-home)# contract-id Company1234 Router(cfg-call-home)# exit
SUMMARY STEPS
1. 2. 3.
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
rate-limit number
Specifies a limit on the number of messages sent per minute. Range 1 to 60. The default is 20.
Example:
Router(cfg-call-home)# rate-limit 40
SUMMARY STEPS
1. 2. 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
service call-home
Example:
Router(config)# service call-home
Step 3
no service call-home
Example:
Router(config)# no service call-home
Sending a Call Home Test Message Manually, page 24 Sending Call Home Alert Group Messages Manually, page 24 Submitting Call Home Analysis and Report Requests, page 25 Sending the Output of a Command to Cisco or an E-Mail Address, page 27t
SUMMARY STEPS
1.
DETAILED STEPS
Command or Action
Step 1
call-home test [test-message] profile name
Purpose Sends a test message to the specified destination profile. The user-defined test message text is optional, but must be enclosed in quotes ( ) if it contains spaces. If no user-defined message is configured, a default message is sent.
Example:
Router# call-home test profile profile1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
Configuration, diagnostic, and inventory alert groups can be sent manually. When you manually trigger an alert group message and you specify a destination profile name, a message is sent to the destination profile regardless of the active status, subscription status, or severity setting of the profile. When you manually trigger a configuration or inventory alert group message and do not specify a destination profile name, a message is sent to all active profiles that have either a normal or periodic subscription to the specified alert group. When you manually trigger a diagnostic alert group message and do not specify a destination profile name, a message is sent to all active profiles that have a lower severity subscription than the severity of the diagnostic results of the specified slot.
To manually trigger Call Home alert group messages, complete the following steps:
SUMMARY STEPS
1. 2. 3.
call-home send alert-group configuration [profile name] call-home send alert-group diagnostic slot R0 [profile name] call-home send alert-group inventory [profile name]
DETAILED STEPS
Command or Action
Step 1
call-home send alert-group configuration [profile name]
Purpose Sends a configuration alert group message to one destination profile if specified, or to all subscribed destination profiles.
Example:
Router# call-home send alert-group configuration profile CiscoTAC-1
Step 2
Example:
Router# call-home send alert-group diagnostic slot R0 profile CiscoTAC-1
Sends a diagnostic alert group message to one destination profile if specified, or to all subscribed destination profiles with a lower severity subscription than the diagnostic result for route processor slot 0.
Step 3
Sends an inventory alert group message to one destination profile if specified, or to all subscribed destination profiles.
Example:
Router# call-home send alert-group inventory
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
25
If a profile name is specified, the request is sent to the profile. If no profile is specified, the request is sent to the Cisco TAC profile. The recipient profile does not need to be enabled for the call-home request. The profile should specify the e-mail address where the transport gateway is configured so that the request message can be forwarded to the Cisco TAC and the user can receive the reply from the Smart Call Home service. The ccoid user-id is the registered identifier of the Smart Call Home user. If the user-id is specified, the response is sent to the e-mail address of the registered user. If no user-id is specified, the response is sent to the contact e-mail address of the device. Based on the keyword specifying the type of report requested, the following information is returned:
config-sanityInformation on best practices as related to the current running configuration. bugs-listKnown bugs in the running version and in the currently applied features. command-referenceReference links to all commands in the running configuration. product-advisoryProduct Security Incident Response Team (PSIRT) notices, End of Life
(EOL) or End of Sales (EOS) notices, or field notices (FN) that may affect devices in your network. To submit a request for analysis and report information from the Cisco Output Interpreter tool, complete the following steps:
SUMMARY STEPS
1. 2.
call-home request output-analysis show-command [profile name] [ccoid user-id] call-home request {config-sanity | bugs-list | command-reference | product-advisory} [profile name] [ccoid user-id]
DETAILED STEPS
Command or Action
Step 1
call-home request output-analysis show-command [profile name] [ccoid user-id]
Purpose Sends the output of the specified show command for analysis. The show command must be contained in quotes ().
Example:
Router# call-home request output-analysis show diag profile TG
Step 2
call-home request {config-sanity | bugs-list | command-reference | product-advisory} [profile name] [ccoid user-id]
Example:
Router# call-home request config-sanity profile TG
Sends the output of a predetermined set of commands, such as the show running-config all and show version commands, for analysis. In addition, the call home request product-advisory subcommand includes all inventory alert group commands. The keyword specified after the call-home request command specifies the type of report requested.
Example
The following example shows a request for analysis of a user-specified show command:
Router# call-home request output-analysis "show diag" profile TG
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
26
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
The specified CLI command can be any run command, including commands for all modules. The command must be contained in quotes (). If an e-mail address is specified, the command output is sent to that address. If no e-mail address is specified, the output is sent to the Cisco TAC (attach@cisco.com). The e-mail is sent in long text format with the service number, if specified, in the subject line. The service number is required only if no e-mail address is specified, or if a Cisco TAC e-mail address is specified.
To execute a CLI command and e-mail the command output, complete the following step:
SUMMARY STEPS
1.
call-home send command {email email-addr [tac-service-request request-number] | tac-service-request request-number email email-addr}
DETAILED STEPS
Command or Action
Step 1
call-home send command {email email-addr [tac-service-request request-number] | tac-service-request request-number [email email-addr]}
Purpose Executes the specified CLI command and e-mails the output, where:
Example:
Router# call-home send show call-home email support@example.com
email email-addrSpecifies the email address to which the command output should be sent. This keyword is optional if used after entering the tac-service-request option. tac-service-request request-numberSpecifies the TAC service request number that will appear in the subject line of the email. This keyword is optional if used after entering the email option.
Example
The following example shows how to send the output of a CLI command to a user-specified e-mail address: Router# call-home send "show diag" email support@example.com
How To Configure Call Home to Support the Smart Call Home Service
.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
27
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
This section provides an overview of the minimum steps required to configure the Call Home feature on a Cisco device, and other required supporting configuration to communicate securely with the Smart Call Home service using HTTPS:
Prerequisites, page 28 (required) Configure and Enable Call Home, page 28 (required) Declare and Authenticate a CA Trustpoint, page 31 (required) Start Smart Call Home Registration, page 33 (required)
Prerequisites
Before you configure and use the Smart Call Home Service, be sure that you have completed the following prerequisites:
Verify that you have an active Cisco Systems service contract for the device being configured. Verify that you have IP connectivity to the Cisco HTTPS server. Obtain the latest Cisco Systems server security certificate. In Cisco IOS XE Release 2.6.0, the following shows the latest text for the Cisco Systems server security certificate:
MIIDAjCCAmsCEH3Z/gfPqB63EHln+6eJNMYwDQYJKoZIhvcNAQEFBQAwgcExCzAJ BgNVBAYTAlVTMRcwFQYDVQQKEw5WZXJpU2lnbiwgSW5jLjE8MDoGA1UECxMzQ2xh c3MgMyBQdWJsaWMgUHJpbWFyeSBDZXJ0aWZpY2F0aW9uIEF1dGhvcml0eSAtIEcy MTowOAYDVQQLEzEoYykgMTk5OCBWZXJpU2lnbiwgSW5jLiAtIEZvciBhdXRob3Jp emVkIHVzZSBvbmx5MR8wHQYDVQQLExZWZXJpU2lnbiBUcnVzdCBOZXR3b3JrMB4X DTk4MDUxODAwMDAwMFoXDTI4MDgwMTIzNTk1OVowgcExCzAJBgNVBAYTAlVTMRcw FQYDVQQKEw5WZXJpU2lnbiwgSW5jLjE8MDoGA1UECxMzQ2xhc3MgMyBQdWJsaWMg UHJpbWFyeSBDZXJ0aWZpY2F0aW9uIEF1dGhvcml0eSAtIEcyMTowOAYDVQQLEzEo YykgMTk5OCBWZXJpU2lnbiwgSW5jLiAtIEZvciBhdXRob3JpemVkIHVzZSBvbmx5 MR8wHQYDVQQLExZWZXJpU2lnbiBUcnVzdCBOZXR3b3JrMIGfMA0GCSqGSIb3DQEB AQUAA4GNADCBiQKBgQDMXtERXVxp0KvTuWpMmR9ZmDCOFoUgRm1HP9SFIIThbbP4 pO0M8RcPO/mn+SXXwc+EY/J8Y8+iR/LGWzOOZEAEaMGAuWQcRXfH2G71lSk8UOg0 13gfqLptQ5GVj0VXXn7F+8qkBOvqlzdUMG+7AUcyM83cV5tkaWH4mx0ciU9cZwID AQABMA0GCSqGSIb3DQEBBQUAA4GBAFFNzb5cy5gZnBWyATl4Lk0PZ3BwmcYQWpSk U01UbSuvDV1Ai2TT1+7eVmGSX6bEHRBhNtMsJzzoKQm5EWR0zLVznxxIqbxhAe7i F6YM40AIOw7n60RzKprxaZLvcRTDOaxxp5EJb+RxBrO6WVcmeQD2+A2iMzAo1KpY oJ2daZH9
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
28
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
configure terminal call-home profile CiscoTAC-1 destination transport-method http active exit contact-email-addr email-address exit service call-home
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
29
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
call-home
Example:
Router(config)# call-home
Step 3
profile CiscoTAC-1
Enters call home destination profile configuration mode for the CiscoTAC-1 destination profile.
Example:
Router(config-call-home)# profile CiscoTAC-1
Step 4
(Required only if using HTTPS) Configures the message transport method for http.
Example:
Router(cfg-call-home-profile)# destination transport-method http
Step 5
active
Example:
Router(cfg-call-home-profile)# active
Step 6
exit
Exits call home destination profile configuration mode and returns to call home configuration mode.
Example:
Router(cfg-call-home-profile)# exit
Step 7
contact-email-addr email-address
Assigns the customers e-mail address. Enter up to 200 characters in e-mail address format with no spaces.
Example:
Router(cfg-call-home)# contact-email-addr username@example.com
Step 8
exit
Exits call home configuration mode and returns to global configuration mode.
Example:
Router(cfg-call-home)# exit
Step 9
service call-home
Example:
Router(config)# service call-home
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
30
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
Command or Action
Step 10
exit
Purpose Exits global configuration mode and returns to privileged EXEC mode.
Example:
Router(config)# exit
Step 11
Example:
Router# copy running-config startup-config
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
configure terminal crypto pki trustpoint name enrollment terminal exit crypto pki authenticate name At the prompt, paste the security certificate text. quit yes end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
31
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
Example:
Router(config)# crypto pki trustpoint cisco
Step 3
enrollment terminal
Example:
Router(ca-trustpoint)# enrollment terminal
Step 4
exit
Example:
Router(ca-trustpoint)# exit
Step 5
Example:
Router(config)# crypto pki authenticate cisco
The CA name should match the name specified in the crypto pki trustpoint command.
Step 6
Example:
quit
Step 8
yes
Example:
% Do you accept this certificate? [yes/no]: yes
Step 9
end
Example:
Router# end
Step 10
Example:
Router# copy running-config startup-config
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
32
Configuring Call Home How To Configure Call Home to Support the Smart Call Home Service
Examples
The following example shows the configuration for declaring and authenticating the Cisco server security certificate:
Router# configure terminal Router(config)# crypto pki trustpoint cisco Router(ca-trustpoint)# enrollment terminal Router(ca-trustpoint)# exit Router(config)# crypto pki authenticate cisco Enter the base 64 encoded CA certificate. End with a blank line or the word "quit" on a line by itself MIIDAjCCAmsCEH3Z/gfPqB63EHln+6eJNMYwDQYJKoZIhvcNAQEFBQAwgcExCzAJ BgNVBAYTAlVTMRcwFQYDVQQKEw5WZXJpU2lnbiwgSW5jLjE8MDoGA1UECxMzQ2xh c3MgMyBQdWJsaWMgUHJpbWFyeSBDZXJ0aWZpY2F0aW9uIEF1dGhvcml0eSAtIEcy MTowOAYDVQQLEzEoYykgMTk5OCBWZXJpU2lnbiwgSW5jLiAtIEZvciBhdXRob3Jp emVkIHVzZSBvbmx5MR8wHQYDVQQLExZWZXJpU2lnbiBUcnVzdCBOZXR3b3JrMB4X DTk4MDUxODAwMDAwMFoXDTI4MDgwMTIzNTk1OVowgcExCzAJBgNVBAYTAlVTMRcw FQYDVQQKEw5WZXJpU2lnbiwgSW5jLjE8MDoGA1UECxMzQ2xhc3MgMyBQdWJsaWMg UHJpbWFyeSBDZXJ0aWZpY2F0aW9uIEF1dGhvcml0eSAtIEcyMTowOAYDVQQLEzEo YykgMTk5OCBWZXJpU2lnbiwgSW5jLiAtIEZvciBhdXRob3JpemVkIHVzZSBvbmx5 MR8wHQYDVQQLExZWZXJpU2lnbiBUcnVzdCBOZXR3b3JrMIGfMA0GCSqGSIb3DQEB AQUAA4GNADCBiQKBgQDMXtERXVxp0KvTuWpMmR9ZmDCOFoUgRm1HP9SFIIThbbP4 pO0M8RcPO/mn+SXXwc+EY/J8Y8+iR/LGWzOOZEAEaMGAuWQcRXfH2G71lSk8UOg0 13gfqLptQ5GVj0VXXn7F+8qkBOvqlzdUMG+7AUcyM83cV5tkaWH4mx0ciU9cZwID AQABMA0GCSqGSIb3DQEBBQUAA4GBAFFNzb5cy5gZnBWyATl4Lk0PZ3BwmcYQWpSk U01UbSuvDV1Ai2TT1+7eVmGSX6bEHRBhNtMsJzzoKQm5EWR0zLVznxxIqbxhAe7i F6YM40AIOw7n60RzKprxaZLvcRTDOaxxp5EJb+RxBrO6WVcmeQD2+A2iMzAo1KpY oJ2daZH9 quit Certificate has the following attributes: Fingerprint MD5: A2339B4C 747873D4 6CE7C1F3 8DCB5CE9 Fingerprint SHA1: 85371CA6 E550143D CE280347 1BDE3A09 E8F8770F % Do you accept this certificate? [yes/no]: yes Trustpoint CA certificate accepted. % Certificate successfully imported Router(config)# end Router# copy running-config startup-config
SUMMARY STEPS
1.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
33
DETAILED STEPS
Command or Action
Step 1
call-home send alert-group inventory profile CiscoTAC-1
Purpose Sends an inventory alert group message to the CiscoTAC-1 destination profile.
Example:
Router# call-home send alert-group inventory profile CiscoTAC-1
What To Do Next
To receive an email from Cisco Systems and follow the instructions to complete the device registration in the Smart Call Home web application:
Launch the Smart Call Home web application at the following URL: https://tools.cisco.com/sch/ Accept the Legal Agreement. Confirm device registration for Call Home devices with pending registration.
For more information about using the Smart Call Home web application, see Smart Call Home User Guide. This user guide also includes configuration examples for sending Smart Call Home messages directly from your device or through a transport gateway (TG) aggregation point. You can use a TG aggregation point in cases requiring support for multiple devices or in cases where security requirements mandate that your devices must not be connected directly to the Internet.
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
show call-home show call-home detail show call-home alert-group show call-home mail-server status show call-home profile {all | name} show call-home statistics
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
34
DETAILED STEPS
Command or Action
Step 1
show call-home
Example:
Router# show call-home
Step 2
Example:
Router# show call-home detail
Step 3
Example:
Router# show call-home alert-group
Step 4
Example:
Router# show call-home mail-server status
Step 5
Example:
Router# show call-home profile all
Displays the configuration of the specified destination profile. Use the all keyword to display the configuration of all destination profiles. Displays the statistics of Call Home events.
Step 6
Example:
Router# show call-home statistics
Examples
The following examples show the sample output when using different options of the show call-home command.
Example: Configured Call Home Information in Summary
Router# show call-home Current call home settings: call home feature : disable call home message's from address: username@example.com call home message's reply-to address: username@example.com vrf for call-home messages: Mgmt-intf contact person's email address: username@example.com contact person's phone number: +14085551234 street address: 1234 Any Street Any city Any state 12345 customer ID: customer@example.com contract ID: 123456789 site ID: example.com Mail-server[1]: Address: smtp.example.com Priority: 1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
35
Mail-server[2]: Address: 192.168.0.1 Priority: 2 Rate-limit: 20 message(s) per minute Available alert groups: Keyword -----------------------configuration diagnostic environment inventory syslog Profiles: Profile Name: campus-noc Profile Name: CiscoTAC-1
Description ------------------------------configuration info diagnostic info environmental info inventory info syslog info
Description ------------------------------configuration info diagnostic info environmental info inventory info syslog info
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
36
Profile Name: CiscoTAC-1 Profile status: INACTIVE Preferred Message Format: xml Message Size Limit: 3145728 Bytes Transport Method: email Email address(es): callhome@cisco.com HTTP address(es): https://tools.cisco.com/its/service/oddce/services/DDCEService Periodic configuration info message is scheduled every 23 day of the month at 10:28 Periodic inventory info message is scheduled every 23 day of the month at 10:13 Alert-group -----------------------diagnostic environment inventory Syslog-Pattern -----------------------.* Severity -----------minor minor normal Severity -----------major
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
37
Profile Name: CiscoTAC-1 Profile status: INACTIVE Preferred Message Format: xml Message Size Limit: 3145728 Bytes Transport Method: email Email address(es): callhome@cisco.com HTTP address(es): https://tools.cisco.com/its/service/oddce/services/DDCEService Periodic configuration info message is scheduled every 23 day of the month at 12:13 Periodic inventory info message is scheduled every 23 day of the month at 11:58 Alert-group -----------------------diagnostic environment inventory Syslog-Pattern -----------------------.* Router# Severity -----------minor minor normal Severity -----------major
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
38
Environment Inventory SysLog Test Request Send-CLI Total Failed Config Diagnostic Environment Inventory SysLog Test Request Send-CLI Total Ratelimit -dropped Config Diagnostic Environment Inventory SysLog Test Request Send-CLI
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
Default Settings
Table 2 lists the default Call Home settings.
Table 2 Default Call Home Settings
Parameters Call Home feature status User-defined profile status Predefined Cisco TAC profile status Transport method Message format type Alert group status Call Home message severity threshold Message rate limit for messages per minute
Destination message size for a message sent in long text, short text, or XML format 3,145,728
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
39
Syslog Event
Description and CLI Commands Severity Executed User-generated request for configuration. (Sent to TAC.) CLI commands executed: show platform show inventory show running-config all show startup-config show version
Diagnostic
CLI commands executed: show platform show diagnostic result slot x detail show version show inventory show buffers show logging show diagnostic result slot all show diagnostic events slot all
Error Counter %ASR1000_RP_DIAG_TEST-4Monitoring Test ERR_CNTR_HM_TEST_FAIL failure count exceeds threshold Error Counter %ASR1000_RP_DIAG_TEST-4Monitoring Test ERR_CNTR_HM_TEST_DATA failure count exceeds threshold
ERROR_COUNTER_WARNING: Slot number Error counter exceeds threshold, system operation continue. ERROR_COUNTER_DATA: ID:number IN:number PO:number RE:number RM:number DV:number EG:number CF:number TF:number Events related to power, fan, and environment sensing elements, such as temperature alarms. (Sent to TAC.) CLI commands executed: show platform show environment show inventory show logging
Environmental
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
40
Table 3
Alert Group
Description and CLI Commands Severity Executed 3 The fan in slot (slot/subslot number) is encountering a failure condition. The fan in slot (slot/subslot number) is functioning properly. The PEM in slot (slot number) is switched off or encountering a failure condition. The PEM in slot (slot number) is functioning properly. Any sensor in fp/cc/rp has exceeded a certain threshold and resulted in this environmental alert. Any sensor in fp/cc/rp has failed and resulted in this environmental alert. Any sensor in fp/cc/rp has recovered and resulted in this environmental alert. Inventory status should be provided whenever a unit is cold-booted, or when FRUs are inserted or removed. This is considered a noncritical event, and the information is used for status and entitlement. (Sent to TAC.) CLI commands executed: show platform show inventory oid show version show diag all eeprom detail
%ASR1000_PEM-6-FANOK %ASR1000_PEM-3-PEMFAIL
6 3
%ASR1000_PEM-6-PEMOK %ENVIRONMENTAL-1-ALERT
6 1
ENVM
%ENVIRONMENTAL-1-SENSORFAIL
%ENVIRONMENTAL-1-SENSOROK
Inventory
%ASR1000_OIR-6-REMSPA
SPA removed from subslot (slot/subslot number) and the interfaces are disabled. SPA inserted in subslot (slot/subslot number). Card (cc/rp/fp) removed from slot (slot number). Card (cc/rp/fp) inserted in slot (slot number).
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
41
Table 3
Alert Group
Description and CLI Commands Severity Executed 6 PEM/FM slot (slot number) removed. PEM/FM slot (slot number) inserted. Event logged to syslog. CLI commands executed: show inventory show logging
Syslog
Test
0 1 2 3 4 5 6 7
System is unusable. Action must be taken immediately. Critical conditions. Error conditions. Warning conditions. Normal but signification condition. Informational. Debug-level messages. User-generated test message. (Sent to TAC.) CLI commands executed: show platform show inventory show version
Message Contents
The following tables display the content formats of alert group messages:
Table 4 describes the content fields of a short text message. Table 5 describes the content fields that are common to all long text and XML messages. The fields specific to a particular alert group message are inserted at a point between the common fields. The insertion point is identified in the table. Table 6 describes the inserted content fields for reactive messages (system failures that require a TAC case) and proactive messages (issues that might result in degraded system performance). Table 7 describes the inserted content fields for an inventory message. Sample Syslog Alert Notification in Long Text Format, page 46 Sample Syslog Alert Notification in XML Format, page 50
This section also includes the following subsections that provide sample messages:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
42
Table 4
Data Item Device identification Date/time stamp Error isolation message Alarm urgency level
Description Configured device name Time stamp of the triggering event Plain English description of triggering event Error level such as that applied to a system message
Table 5
Data Item Description (Plain Text and XML) (Plain Text and XML) Time stamp Message name Date and time stamp of event in ISO time notation: YYYY-MM-DD HH:MM:SS GMT+HH:MM. Name of message. Specific event names are listed in the Alert Group Trigger Events and Commands section on page 40. Specifically Call Home. Specific type of message: full, delta, test Specifically reactive. Optional, because default is reactive. Severity level of message (see Table 1).
MML Tag (XML Only) CallHome/EventTime For short text message only
Message type Message subtype Message group Severity level Source ID Device ID
Product type for routing through the workflow engine. This For long-text message only is typically the product family name. Unique device identifier (UDI) for end device generating message. This field should be empty if the message is nonspecific to a fabric switch. The format is type@Sid@serial.
CallHome/CustomerData/ ContractData/DeviceId
type is the product model number from backplane IDPROM. @ is a separator character. Sid is C, identifying the serial ID as a chassis serial number. serial is the number identified by the Sid field. CallHome/CustomerData/ ContractData/CustomerId CallHome/CustomerData/ ContractData/ContractId CallHome/CustomerData/ ContractData/SiteId
Example: ASR1006@C@FOX105101DH Customer ID Contract ID Site ID Optional user-configurable field used for contract information or other ID by any support service. Optional user-configurable field used for contract information or other ID by any support service. Optional user-configurable field used for site IDs supplied by Cisco Systems or other data meaningful to alternate support services.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
43
Table 5
Common Fields for All Long Text and XML Messages (continued)
Data Item Description (Plain Text and XML) (Plain Text and XML) Server ID
If the message is generated from the fabric switch, this is the For long text message only unique device identifier (UDI) of the switch. The format is type@Sid@serial.
type is the product model number from backplane IDPROM. @ is a separator character. Sid is C, identifying the serial ID as a chassis serial number. serial is the number identified by the Sid field. CallHome/MessageDescription
Example: ASR1006@C@FOX105101DH Message description Short text describing the error. Device name Contact name Contact e-mail Contact phone number Street address Model name Serial number Node that experienced the event. This is the host name of the CallHome/CustomerData/ device. SystemInfo/NameName Name of person to contact for issues associated with the node experiencing the event. E-mail address of person identified as contact for this unit. CallHome/CustomerData/ SystemInfo/Contact CallHome/CustomerData/ SystemInfo/ContactEmail
Phone number of the person identified as the contact for this CallHome/CustomerData/ unit. SystemInfo/ContactPhoneNumber Optional field containing street address for RMA part shipments associated with this unit. CallHome/CustomerData/ SystemInfo/StreetAddress
Model name of the router. This is the specific model as part CallHome/Device/Cisco_Chassis/ of a product family name. Model Chassis serial number of the unit. CallHome/Device/Cisco_Chassis/ SerialNumber CallHome/Device/Cisco_Chassis/ AdditionalInformation/AD@name= PartNumber CallHome/Device/Cisco_Chassis/ AdditionalInformation/AD@name= sysObjectID CallHome/Device/Cisco_Chassis/ AdditionalInformation/AD@name= sysDescr
System object ID
System description
Fields specific to a particular alert group message are inserted here. The following fields may be repeated if multiple CLI commands are executed for this alert group. Command output name Attachment type The exact name of the issued CLI command. Attachment type. Usually inline. /aml/Attachments/Attachment/Name /aml/Attachments/Attachment@type
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
44
Table 5
Common Fields for All Long Text and XML Messages (continued)
Data Item Description (Plain Text and XML) (Plain Text and XML) MIME type Command output text Normally text or plain or encoding type. Output of command automatically executed (see Table 3).
Table 6
Data Item Description (Plain Text and XML) (Plain Text and XML) Chassis hardware version Supervisor module software version Hardware version of chassis. Top-level software version.
MML Tag (XML Only) CallHome/Device/Cisco_Chassis/ HardwareVersion CallHome/Device/Cisco_Chassis/ AdditionalInformation/AD@name= SoftwareVersion CallHome/Device/Cisco_Chassis/ Cisco_Card/Model CallHome/Device/Cisco_Chassis/ Cisco_Card/SerialNumber CallHome/Device/Cisco_Chassis/ Cisco_Card/PartNumber CallHome/Device/Cisco_Chassis/ Cisco_Card/LocationWithinContainer CallHome/Device/Cisco_Chassis/ Cisco_Card/HardwareVersion CallHome/Device/Cisco_Chassis/ Cisco_Card/SoftwareIdentity/ VersionString
Affected FRU name Name of the affected FRU generating the event message. Affected FRU serial Serial number of affected FRU. number Affected FRU part number FRU slot FRU hardware version FRU software version Part number of affected FRU. Slot number of FRU generating the event message. Hardware version of affected FRU. Software version(s) running on affected FRU.
Table 7
Data Item Description (Plain Text and XML) (Plain Text and XML) Chassis hardware version Supervisor module software version FRU name FRU s/n Hardware version of chassis. Top-level software version.
MML Tag (XML Only) CallHome/Device/Cisco_Chassis/ HardwareVersion CallHome/Device/Cisco_Chassis/ AdditionalInformation/AD@name= SoftwareVersion CallHome/Device/Cisco_Chassis/ Cisco_Card/Model CallHome/Device/Cisco_Chassis/ Cisco_Card/SerialNumber
Name of the affected FRU generating the event message. Serial number of FRU.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
45
Table 7
Data Item Description (Plain Text and XML) (Plain Text and XML) FRU part number FRU slot FRU hardware version FRU software version Part number of FRU. Slot number of FRU. Hardware version of FRU. Software version(s) running on FRU.
MML Tag (XML Only) CallHome/Device/Cisco_Chassis/ Cisco_Card/PartNumber CallHome/Device/Cisco_Chassis/ Cisco_Card/LocationWithinContainer CallHome/Device/Cisco_Chassis/ CiscoCard/HardwareVersion CallHome/Device/Cisco_Chassis/ Cisco_Card/SoftwareIdentity/ VersionString
Console logging: disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 112 messages logged, xml disabled,
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
46
filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled No active filter modules. Trap logging: level informational, 104 message lines logged Log Buffer (1000000 bytes): *Dec 3 07:16:55.020: ASR1000-RP HA: RF status CID 1340, seq 93, status RF_STATUS_REDUNDANCY_MODE_CHANGE, op 0, state DISABLED, peer DISABLED *Dec 3 07:17:00.379: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001 *Dec 3 07:17:00.398: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun *Dec 3 07:17:00.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface EOBC0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface LIIN0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.818: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded from the Shell Manager *Dec 3 07:16:30.926: %CMRP-5-PRERELEASE_HARDWARE: R0/0: cmand: 2 is pre-release hardware *Dec 3 07:16:24.147: %HW_IDPROM_ENVMON-3-HW_IDPROM_CHECKSUM_INVALID: F1: cman_fp: The idprom contains an invalid checksum in a sensor entry. Expected: 63, calculated: fe *Dec 3 07:16:24.176: %CMFP-3-IDPROM_SENSOR: F1: cman_fp: One or more sensor fields from the idprom failed to parse properly because Success. *Dec 3 07:16:27.669: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:27.839: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:28.659: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:28.799: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.557: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.812: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:33.532: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:33.786: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:34.158: %IOSXE-6-PLATFORM: F1: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:35.134: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:38.965: %CMRP-6-FP_HA_STATUS: R0/0: cmand: F0 redundancy state is Active with ready Standby *Dec 3 07:17:01.926: %DYNCMD-7-PKGINT_INSTALLED: The command package 'platform_trace' has been succesfully installed
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
47
*Dec 3 12:17:05.385 IST: %SYS-6-CLOCKUPDATE: System clock has been updated from 07:17:05 UTC Thu Dec 3 2009 to 12:17:05 IST Thu Dec 3 2009, configured from console by console. *Dec 3 12:17:05.506 IST: %SYS-5-CONFIG_I: Configured from memory by console *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/2, interfaces disabled *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/3, interfaces disabled *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 2/3, interfaces disabled *Dec 3 12:17:05.514 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-8XOC3-POS) offline in subslot 0/2 *Dec 3 12:17:05.515 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4XOC3-POS) offline in subslot 1/3 *Dec 3 12:17:05.516 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-1XOC12-POS) offline in subslot 2/3 *Dec 3 12:17:05.520 IST: %ASR1000_OIR-6-INSCARD: Card (rp) inserted in slot R1 *Dec 3 12:17:05.521 IST: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F0 *Dec 3 12:17:05.521 IST: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0 *Dec 3 12:17:05.574 IST: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F1 *Dec 3 12:17:05.574 IST: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F1 *Dec 3 12:17:05.575 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 0 *Dec 3 12:17:05.575 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Dec 3 12:17:05.576 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Dec 3 12:17:05.580 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 1 *Dec 3 12:17:05.581 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 1 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/3 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 2 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 2 *Dec 3 12:17:05.583 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 2/3 *Dec 3 12:17:05.844 IST: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version 12.2(20091118:075558) [v122_33_xnf_asr_rls6_throttle-mcp_dev_rls6 102] Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 18-Nov-09 01:14 by *Dec 3 12:17:06.005 IST: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF *Dec 3 12:17:06.005 IST: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF *Dec 3 12:16:30.097 IST: %LINK-3-UPDOWN: SIP2/3: Interface EOBC2/1, changed state to up *Dec 3 12:16:27.595 IST: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up *Dec 3 12:16:26.420 IST: %LINK-3-UPDOWN: SIP1/3: Interface EOBC1/1, changed state to up *Dec 3 12:17:07.435 IST: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF *Dec 3 12:17:07.435 IST: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF *Dec 3 12:17:07.476 IST: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up *Dec 3 12:17:08.137 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XOC3-POS) online in subslot 1/3 *Dec 3 12:17:08.139 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-8XOC3-POS) online in subslot 0/2 *Dec 3 12:17:08.346 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 2/3 *Dec 3 12:17:08.491 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up *Dec 3 12:17:11.047 IST: %SYS-6-BOOTTIME: Time taken to reboot after reload = 12319 seconds *Dec 3 12:17:11.562 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[879]: xinetd Version 2.3.14 started with no options compiled in. *Dec 3 12:17:11.562 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[879]: Started working: 1 available service *Dec 3 12:17:11.584 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[887]: xinetd Version 2.3.14 started with no options compiled in. *Dec 3 12:17:11.584 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[887]: Started working: 2 available services *Dec 3 12:17:13.753 IST: %LINK-3-UPDOWN: Interface POS0/2/0, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/1, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/2, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/3, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/4, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/5, changed state to down
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
48
*Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/6, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/7, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/1, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/2, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/3, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/4, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/5, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/6, changed state to down *Dec 3 12:17:14.755 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/7, changed state to down *Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/1: SLOS declared *Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/2: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/3: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/4: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/5: SLOS declared *Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/6: SLOS declared *Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/7: SLOS declared *Dec 3 12:17:14.850 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0, changed state to down *Dec 3 12:17:14.851 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0, changed state to down *Dec 3 12:17:16.069 IST: %LINK-3-UPDOWN: Interface POS0/2/0, changed state to up *Dec 3 12:17:15.734 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/0, changed state to up *Dec 3 12:17:16.868 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to up *Dec 3 12:17:16.905 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to up *Dec 3 12:17:16.538 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/7, changed state to down *Dec 3 12:17:17.070 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0, changed state to up *Dec 3 12:17:16.488 IST: %LINK-3-UPDOWN: SIP1/3: Interface POS1/3/0, changed state to up *Dec 3 12:17:17.868 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0, changed state to up *Dec 3 12:17:16.199 IST: %LINK-3-UPDOWN: SIP2/3: Interface POS2/3/0, changed state to up *Dec 3 12:17:17.905 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0, changed state to up *Dec 3 12:22:01.574 IST: %IP-4-DUPADDR: Duplicate address 172.27.55.233 on GigabitEthernet0, sourced by 001a.3044.1ec0 *Dec 3 12:23:47.613 IST: %SYS-5-CONFIG_I: Configured from console by console *Dec 3 12:24:37.134 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console *Dec 3 12:25:34.356 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has failed. Error code = 0x1 (DIAG_FAILURE) *Dec 3 12:25:39.459 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has failed. Error code = 0x1 (DIAG_FAILURE) *Dec 3 12:25:54.405 IST: %SYS-5-CONFIG_I: Configured from console by console mcp-6ru-3# Command Output Name : show inventory Attachment Type : command output MIME Type : text/plain Command Output Text : NAME: "Chassis", DESCR: "Cisco ASR1006 Chassis" PID: ASR1006 , VID: V00, SN: FOX105101DH NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: MCP-CC , VID: V00, SN: JAB1104064W
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
49
NAME: "SPA subslot 0/2", DESCR: "8-port OC3/STM1 POS Shared Port Adapter" PID: SPA-8XOC3-POS , VID: V01, SN: JAE1236TSW0 NAME: "subslot 0/2 transceiver 0", DESCR: "OC3 SR-1/STM1 MM" PID: SFP-OC3-MM , VID: A , SN: OCP12231628 NAME: "module 1", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: MCP-CC , VID: V00, SN: JAB1104062X NAME: "SPA subslot 1/3", DESCR: "4-port OC3/STM1 POS Shared Port Adapter" PID: SPA-4XOC3-POS , VID: V01, SN: JAB085202QU NAME: "subslot 1/3 transceiver 0", DESCR: "OC3 SR-1/STM1 MM" PID: SFP-OC3-MM , VID: A , SN: OCP12310174 NAME: "module 2", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: ASR1000-SIP10 , VID: V00, SN: JAB113701L9 NAME: "SPA subslot 2/3", DESCR: "1-port OC12/STM4 POS Shared Port Adapter" PID: SPA-1XOC12-POS , VID: V01, SN: JAE1236U41L NAME: "subslot 2/3 transceiver 0", DESCR: "OC12 SR-1/STM4 MM" PID: SFP-OC12-MM , VID: A , SN: OCP10100281 NAME: "module R0", DESCR: "Cisco ASR1000 Route Processor 1" PID: ASR1000-RP1 , VID: V00, SN: JAB11110181 NAME: "module R1", DESCR: "Cisco ASR1000 Route Processor 1" PID: ASR1000-RP1 , VID: V00, SN: JAB1111016K NAME: "module F0", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps" PID: ASR1000-ESP10 , VID: V00, SN: JAB111801ZX NAME: "module F1", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps" PID: ASR1000-ESP10 , VID: V00, SN: JAB111101AP NAME: "Power Supply Module 0", DESCR: "Cisco ASR1006 AC Power Supply" PID: TBD000000000000000, VID: +^A , SN: ART1114Q00F NAME: "Fan Module 1", DESCR: "Cisco ASR1006 Fan Module" PID: TBD000000000000000, VID: +^A , SN: ART1115P00D
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
50
<aml-block:Header> <aml-block:Type>http://www.cisco.com/2005/05/callhome/syslog</aml-block:Type> <aml-block:CreationDate>2009-12-03 12:29:02 GMT+05:00</aml-block:CreationDate> <aml-block:Builder> <aml-block:Name>ASR1000</aml-block:Name> <aml-block:Version>2.0</aml-block:Version> </aml-block:Builder> <aml-block:BlockGroup> <aml-block:GroupId>G1:FOX105101DH:CEC1E73E</aml-block:GroupId> <aml-block:Number>0</aml-block:Number> <aml-block:IsLast>true</aml-block:IsLast> <aml-block:IsPrimary>true</aml-block:IsPrimary> <aml-block:WaitForPrimary>false</aml-block:WaitForPrimary> </aml-block:BlockGroup> <aml-block:Severity>2</aml-block:Severity> </aml-block:Header> <aml-block:Content> <ch:CallHome xmlns:ch="http://www.cisco.com/2005/05/callhome" version="1.0"> <ch:EventTime>2009-12-03 12:29:01 GMT+05:00</ch:EventTime> <ch:MessageDescription>*Dec 3 12:29:01.017 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console</ch:MessageDescription> <ch:Event> <ch:Type>syslog</ch:Type> <ch:SubType></ch:SubType> <ch:Brand>Cisco Systems</ch:Brand> <ch:Series>ASR1000 Series Routers</ch:Series> </ch:Event> <ch:CustomerData> <ch:UserData> <ch:Email>username@example.com</ch:Email> </ch:UserData> <ch:ContractData> <ch:CustomerId>username@example.com</ch:CustomerId> <ch:SiteId>example.com</ch:SiteId> <ch:ContractId>123456789</ch:ContractId> <ch:DeviceId>ASR1006@C@FOX105101DH</ch:DeviceId> </ch:ContractData> <ch:SystemInfo> <ch:Name>mcp-6ru-3</ch:Name> <ch:Contact></ch:Contact> <ch:ContactEmail>username@example.com</ch:ContactEmail> <ch:ContactPhoneNumber>+14085551234</ch:ContactPhoneNumber> <ch:StreetAddress>1234 Any Street Any City Any State 12345</ch:StreetAddress> </ch:SystemInfo> <ch:CCOID></ch:CCOID> </ch:CustomerData> <ch:Device> <rme:Chassis xmlns:rme="http://www.cisco.com/rme/4.0"> <rme:Model>ASR1006</rme:Model> <rme:HardwareVersion>2.1</rme:HardwareVersion> <rme:SerialNumber>FOX105101DH</rme:SerialNumber> <rme:AdditionalInformation> <rme:AD name="PartNumber" value="68-2584-05" /> <rme:AD name="SoftwareVersion" value="" /> <rme:AD name="SystemObjectId" value="1.3.6.1.4.1.9.1.925" /> <rme:AD name="SystemDescription" value="Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version 12.2(20091118:075558) [v122_33_xnf_asr_rls6_throttle-mcp_dev_rls6 102] Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 18-Nov-09 01:14 by " /> </rme:AdditionalInformation> </rme:Chassis> </ch:Device> </ch:CallHome>
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
51
</aml-block:Content> <aml-block:Attachments> <aml-block:Attachment type="inline"> <aml-block:Name>show logging</aml-block:Name> <aml-block:Data encoding="plain"> <![CDATA[ Syslog logging: enabled (1 messages dropped, 29 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator.
Console logging: disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 114 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled No active filter modules. Trap logging: level informational, 106 message lines logged Log Buffer (1000000 bytes): *Dec 3 07:16:55.020: ASR1000-RP HA: RF status CID 1340, seq 93, status RF_STATUS_REDUNDANCY_MODE_CHANGE, op 0, state DISABLED, peer DISABLED *Dec 3 07:17:00.379: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001 *Dec 3 07:17:00.398: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun *Dec 3 07:17:00.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface EOBC0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface LIIN0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.818: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded from the Shell Manager *Dec 3 07:16:30.926: %CMRP-5-PRERELEASE_HARDWARE: R0/0: cmand: 2 is pre-release hardware *Dec 3 07:16:24.147: %HW_IDPROM_ENVMON-3-HW_IDPROM_CHECKSUM_INVALID: F1: cman_fp: The idprom contains an invalid checksum in a sensor entry. Expected: 63, calculated: fe *Dec 3 07:16:24.176: %CMFP-3-IDPROM_SENSOR: F1: cman_fp: One or more sensor fields from the idprom failed to parse properly because Success. *Dec 3 07:16:27.669: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:27.839: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
52
*Dec 3 07:16:28.659: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:28.799: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.557: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.812: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:33.532: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:33.786: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:34.158: %IOSXE-6-PLATFORM: F1: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:35.134: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:38.965: %CMRP-6-FP_HA_STATUS: R0/0: cmand: F0 redundancy state is Active with ready Standby *Dec 3 07:17:01.926: %DYNCMD-7-PKGINT_INSTALLED: The command package 'platform_trace' has been succesfully installed *Dec 3 12:17:05.385 IST: %SYS-6-CLOCKUPDATE: System clock has been updated from 07:17:05 UTC Thu Dec 3 2009 to 12:17:05 IST Thu Dec 3 2009, configured from console by console. *Dec 3 12:17:05.506 IST: %SYS-5-CONFIG_I: Configured from memory by console *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/2, interfaces disabled *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 1/3, interfaces disabled *Dec 3 12:17:05.508 IST: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 2/3, interfaces disabled *Dec 3 12:17:05.514 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-8XOC3-POS) offline in subslot 0/2 *Dec 3 12:17:05.515 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-4XOC3-POS) offline in subslot 1/3 *Dec 3 12:17:05.516 IST: %SPA_OIR-6-OFFLINECARD: SPA (SPA-1XOC12-POS) offline in subslot 2/3 *Dec 3 12:17:05.520 IST: %ASR1000_OIR-6-INSCARD: Card (rp) inserted in slot R1 *Dec 3 12:17:05.521 IST: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F0 *Dec 3 12:17:05.521 IST: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0 *Dec 3 12:17:05.574 IST: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F1 *Dec 3 12:17:05.574 IST: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F1 *Dec 3 12:17:05.575 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 0 *Dec 3 12:17:05.575 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0 *Dec 3 12:17:05.576 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/2 *Dec 3 12:17:05.580 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 1 *Dec 3 12:17:05.581 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 1 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 1/3 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 2 *Dec 3 12:17:05.582 IST: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 2 *Dec 3 12:17:05.583 IST: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 2/3 *Dec 3 12:17:05.844 IST: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version 12.2(20091118:075558) [v122_33_xnf_asr_rls6_throttle-mcp_dev_rls6 102] Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 18-Nov-09 01:14 by *Dec 3 12:17:06.005 IST: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF *Dec 3 12:17:06.005 IST: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF *Dec 3 12:16:30.097 IST: %LINK-3-UPDOWN: SIP2/3: Interface EOBC2/1, changed state to up *Dec 3 12:16:27.595 IST: %LINK-3-UPDOWN: SIP0/2: Interface EOBC0/1, changed state to up *Dec 3 12:16:26.420 IST: %LINK-3-UPDOWN: SIP1/3: Interface EOBC1/1, changed state to up *Dec 3 12:17:07.435 IST: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF *Dec 3 12:17:07.435 IST: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF *Dec 3 12:17:07.476 IST: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up *Dec 3 12:17:08.137 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-4XOC3-POS) online in subslot 1/3 *Dec 3 12:17:08.139 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-8XOC3-POS) online in subslot 0/2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
53
*Dec 3 12:17:08.346 IST: %SPA_OIR-6-ONLINECARD: SPA (SPA-1XOC12-POS) online in subslot 2/3 *Dec 3 12:17:08.491 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up *Dec 3 12:17:11.047 IST: %SYS-6-BOOTTIME: Time taken to reboot after reload = 12319 seconds *Dec 3 12:17:11.562 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[879]: xinetd Version 2.3.14 started with no options compiled in. *Dec 3 12:17:11.562 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[879]: Started working: 1 available service *Dec 3 12:17:11.584 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[887]: xinetd Version 2.3.14 started with no options compiled in. *Dec 3 12:17:11.584 IST: %IOSXE-5-PLATFORM: R0/0: xinetd[887]: Started working: 2 available services *Dec 3 12:17:13.753 IST: %LINK-3-UPDOWN: Interface POS0/2/0, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/1, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/2, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/3, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/4, changed state to down *Dec 3 12:17:13.754 IST: %LINK-3-UPDOWN: Interface POS0/2/5, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/6, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS0/2/7, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to down *Dec 3 12:17:13.755 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/1, changed state to down *Dec 3 12:17:14.753 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/2, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/3, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/4, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/5, changed state to down *Dec 3 12:17:14.754 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/6, changed state to down *Dec 3 12:17:14.755 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/7, changed state to down *Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/1: SLOS declared *Dec 3 12:17:14.848 IST: %SONET-4-ALARM: POS0/2/2: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/3: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/4: SLOS declared *Dec 3 12:17:14.849 IST: %SONET-4-ALARM: POS0/2/5: SLOS declared *Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/6: SLOS declared *Dec 3 12:17:14.850 IST: %SONET-4-ALARM: POS0/2/7: SLOS declared *Dec 3 12:17:14.850 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0, changed state to down *Dec 3 12:17:14.851 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0, changed state to down *Dec 3 12:17:16.069 IST: %LINK-3-UPDOWN: Interface POS0/2/0, changed state to up *Dec 3 12:17:15.734 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/0, changed state to up *Dec 3 12:17:16.868 IST: %LINK-3-UPDOWN: Interface POS1/3/0, changed state to up *Dec 3 12:17:16.905 IST: %LINK-3-UPDOWN: Interface POS2/3/0, changed state to up *Dec 3 12:17:16.538 IST: %LINK-3-UPDOWN: SIP0/2: Interface POS0/2/7, changed state to down *Dec 3 12:17:17.070 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS0/2/0, changed state to up *Dec 3 12:17:16.488 IST: %LINK-3-UPDOWN: SIP1/3: Interface POS1/3/0, changed state to up *Dec 3 12:17:17.868 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS1/3/0, changed state to up *Dec 3 12:17:16.199 IST: %LINK-3-UPDOWN: SIP2/3: Interface POS2/3/0, changed state to up
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
54
*Dec 3 12:17:17.905 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0, changed state to up *Dec 3 12:22:01.574 IST: %IP-4-DUPADDR: Duplicate address 172.27.55.233 on GigabitEthernet0, sourced by 001a.3044.1ec0 *Dec 3 12:23:47.613 IST: %SYS-5-CONFIG_I: Configured from console by console *Dec 3 12:24:37.134 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console *Dec 3 12:25:34.356 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has failed. Error code = 0x1 (DIAG_FAILURE) *Dec 3 12:25:39.459 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has failed. Error code = 0x1 (DIAG_FAILURE) *Dec 3 12:25:54.405 IST: %SYS-5-CONFIG_I: Configured from console by console *Dec 3 12:26:02.319 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console *Dec 3 12:28:56.057 IST: %SYS-5-CONFIG_I: Configured from console by console mcp-6ru-3#]]></aml-block:Data> </aml-block:Attachment> <aml-block:Attachment type="inline"> <aml-block:Name>show inventory</aml-block:Name> <aml-block:Data encoding="plain"> <![CDATA[NAME: "Chassis", DESCR: "Cisco ASR1006 Chassis" PID: ASR1006 , VID: V00, SN: FOX105101DH NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: MCP-CC , VID: V00, SN: JAB1104064W NAME: "SPA subslot 0/2", DESCR: "8-port OC3/STM1 POS Shared Port Adapter" PID: SPA-8XOC3-POS , VID: V01, SN: JAE1236TSW0 NAME: "subslot 0/2 transceiver 0", DESCR: "OC3 SR-1/STM1 MM" PID: SFP-OC3-MM , VID: A , SN: OCP12231628 NAME: "module 1", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: MCP-CC , VID: V00, SN: JAB1104062X NAME: "SPA subslot 1/3", DESCR: "4-port OC3/STM1 POS Shared Port Adapter" PID: SPA-4XOC3-POS , VID: V01, SN: JAB085202QU NAME: "subslot 1/3 transceiver 0", DESCR: "OC3 SR-1/STM1 MM" PID: SFP-OC3-MM , VID: A , SN: OCP12310174 NAME: "module 2", DESCR: "Cisco ASR1000 SPA Interface Processor 10" PID: ASR1000-SIP10 , VID: V00, SN: JAB113701L9 NAME: "SPA subslot 2/3", DESCR: "1-port OC12/STM4 POS Shared Port Adapter" PID: SPA-1XOC12-POS , VID: V01, SN: JAE1236U41L NAME: "subslot 2/3 transceiver 0", DESCR: "OC12 SR-1/STM4 MM" PID: SFP-OC12-MM , VID: A , SN: OCP10100281 NAME: "module R0", DESCR: "Cisco ASR1000 Route Processor 1" PID: ASR1000-RP1 , VID: V00, SN: JAB11110181 NAME: "module R1", DESCR: "Cisco ASR1000 Route Processor 1" PID: ASR1000-RP1 , VID: V00, SN: JAB1111016K NAME: "module F0", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps" PID: ASR1000-ESP10 , VID: V00, SN: JAB111801ZX NAME: "module F1", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps" PID: ASR1000-ESP10 , VID: V00, SN: JAB111101AP NAME: "Power Supply Module 0", DESCR: "Cisco ASR1006 AC Power Supply" PID: TBD000000000000000, VID: +^A , SN: ART1114Q00F NAME: "Fan Module 1", DESCR: "Cisco ASR1006 Fan Module"
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
55
PID: TBD000000000000000, VID: +^A , SN: ART1115P00D Router#]]></aml-block:Data> </aml-block:Attachment> </aml-block:Attachments> </aml-block:Block> </soap-env:Body> </soap-env:Envelope>
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
56
Additional References
The following sections provide references related to the Call Home feature.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
57
Related Documents
Related Topic Cisco IOS XE commands Explains how the Smart Call Home service offers web-based access to important information on select Cisco devices and offers higher network availability, and increased operational efficiency by providing proactive diagnostics and real-time alerts. Title Cisco IOS Master Commands List, All Releases Smart Call Home User Guide
Smart Call Home site page on Cisco.com for access to http://www.cisco.com/go/smartcall/ all related product information. Public Key Infrastructure (PKI) and Certificate Authority configuration in Cisco IOS XE software Cisco IOS XE Security Configuration Guide: Secure Connectivity
Standards
Standard Title No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.
MIBs
MIB CISCO-CALLHOME-MIB MIBs Link To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
RFCs
RFC No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature. Title
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
58
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Note
Table 8 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.
Table 8 Feature Information for Call Home
Feature Information Call Home provides e-mail-based and web-based notification of critical system events. A versatile range of message formats are available for optimal compatibility with pager services, standard e-mail, or XML-based automated parsing applications. In Cisco IOS XE Release 2.6, support for this feature was added for the Cisco ASR 1000 Series Aggregation Services Routers. The following commands are new or modified: show diagnostic commands.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
59
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2012 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
60
This guide provides an overview and guidance for configuring the Cisco ASR 1000 Series Aggregation Services Routers with Right-To-Use License (RTU).
Contents
Prerequisites for Cisco RTU License, page 1 Restrictions for Cisco RTU License, page 2 Information About Cisco RTU License, page 2 Configuration Examples for RTU Supported Software Licenses, page 6 Additional References, page 11 Feature Information for Cisco RTU License, page 13
You must obtain the device certificate from the Cisco licensing infrastructure before you start the installation process.
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Overview of the Cisco Licensing Mechanism, page 2 RTU Supported Software Licenses, page 2 Evaluation Licenses and RTU Licenses, page 3
Note
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
An evaluation license is required to activate the licensed features. When a router enters the configuration mode, a check is performed to verify the license. Feature configurations are allowed only valid licenses are available. If a permanent license does not exist, Cisco IOS activates an RTU license when you accept the EULA agreement and the corresponding Cisco IOS functionalities will be available. The RTU license supports the following software features:
Accept the EULA to activate the corresponding feature. Migration of a permanent license from previous versions of the software images are seamless. For information on accepting the EULA, see Example: Accepting the Global EULA, page 6.
License Description
Evaluation License RTU No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Upgrade from 2.5G to 5G license for Cisco ASR1001 Yes Router Software redundancy license for Cisco ASR1000 Series Aggregation Services Routers IPSEC License for Cisco ASR1000 Series Aggregation Services Routers FW License for Cisco ASR1000 Series Aggregation Services Routers Flex. Pack. Insp License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
FLSASR1-FWNAT-R Firewall and NAT Stateful Inter-Chassis Redundancy License FLSASR1-LI FLSASR1-BB FLSASR1-BB-4K FLSASR1-BB-16K FLSASR1-BB-32K Lawful Intercept License for Cisco ASR1000 Series Aggregation Services Routers Broadband License for Cisco ASR1000 Series Aggregation Services Routers Broadband 4K Sessions for Cisco ASR1000 Series Aggregation Services Routers Broadband 16K Sessions for Cisco ASR1000 Series Aggregation Services Routers Broadband 32K Sessions for Cisco ASR1000 Series Aggregation Services Routers
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 1
License Name FLSASR1-CS-250P FLSASR1-CS-2KP FLSASR1-CS-4KP FLSASR1-CS-16KP FLSASR1-CS-32KP FLSASR1-CS-LAB FLSASR1-CS-TPEX SLASR1-AIS SLASR1-AES SLASR1-IPB FLS-ASR1001-5G
License Description CUBE(SP) 250 Session License for Cisco ASR1000 Series Aggregation Services Routers CUBE(SP) 2K Session License for Cisco ASR1000 Series Aggregation Services Routers CUBE(SP) 4K Session License for Cisco ASR1000 Series Aggregation Services Routers CUBE(SP) 16K Session License for Cisco ASR1000 Series Aggregation Services Routers CUBE(SP) 32K Session License for Cisco ASR1000 Series Aggregation Services Routers CUBE(SP) Lab Use Only Lic for Cisco ASR1000 Series Aggregation Services Routers Cisco ASR 1000 Advanced IP Services License Cisco ASR 1000 Advanced Enterprise Services License Cisco ASR 1000 IP BASE License Throughput performance upgrade from 2.5G to 5G license for ASR1001
Evaluation License RTU Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Yes
Yes
Note
Evaluation RTU licenses automatically changes to RTU licenses after an evaluation period of 60 days. Evaluation licenses can be activated using the license boot level {adventerprise | advipservices |ipbase} command.
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
enable configure terminal license boot level {adventerprise | advipservices |ipbase} exit copy running-config startup-config reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router#configure terminal
Step 3
Use the ? command with the technology-package command to see the software packages and features supported on your router.
Step 4
exit
Example:
Router(config)#exit
Step 5
Step 6
reload
Example:
Router#reload
Example
The following example shows how to activate an evaluation license:
Router>enable Router#configure terminal Router(config)#license boot level adventerprise % use 'write' command to make license boot config take effect on next boot Router(config)#exit Router#copy running-config startup-config Router#reload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring a Cisco Right-To-Use License Configuration Examples for RTU Supported Software Licenses
Configuring Throughput, page 6 Example: Accepting the Global EULA, page 6 Example: Accepting an EULA for Software Redundancy License, page 7 Example: Accepting an EULA for the Inter-Chassis Redundancy License, page 7 Example: Accepting an EULA for the Lawful Intercept License, page 8
Configuring Throughput
You can upgrade the throughput of the ESP from 2.5 Gbps to 5 Gbps by activating the RTU license.
For information on configuring throughput on the Cisco ASR 1001 Router, see Cisco ASR 1001 Router Quick Start Guide. For information on configuring throughput on the Cisco ASR 1002-X Router, see Cisco ASR 1001 Router Quick Start Guide.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring a Cisco Right-To-Use License Configuration Examples for RTU Supported Software Licenses
ACCEPT? (yes/[no]): Yes Router(config)# *Jul 6 09:36:11.293: %LICENSE-6-EULA_ACCEPT_ALL: The Right to Use End User License Agreement is accepted
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring a Cisco Right-To-Use License Configuration Examples for RTU Supported Software Licenses
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN. Use of this product feature requires an additional license from Cisco, together with an additional payment. You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the product, including during the 60 day evaluation period, is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day evaluation period, your use of the product feature will be governed solely by the Cisco end user license agreement (link above), together with any supplements relating to such product feature. The above applies even if the evaluation license is not automatically terminated and you do not receive any notice of the expiration of the evaluation period. It is your responsibility to determine when the evaluation period is complete and you are required to make payment to Cisco for your use of the product feature beyond the evaluation period. Your acceptance of this agreement for the software features on one product shall be deemed your acceptance with respect to all such software on all Cisco products you purchase which includes the same software. (The foregoing notwithstanding, you must purchase a license for each software feature you use past the 60 days evaluation period, so that if you enable a software feature on 1000 devices, you must purchase 1000 licenses for use past the 60 day evaluation period.) Activation of the software command line interface will be evidence of your acceptance of this agreement. ACCEPT? (yes/[no]): yes
snmp-server view INTERCEPT_VIEW ciscoIpTapMIB snmp-server view INTERCEPT_VIEW cisco802TapMIB snmp-server view INTERCEPT_VIEW ciscoTap2MIB
The following example shows the acceptance of an EULA for the lawful intercept feature:
Router(config-red)#snmp-server view INTERCEPT_VIEW ciscoIpTapMIB included PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN. Use of this product feature requires an additional license from Cisco, together with an additional payment. You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the product, including during the 60 day evaluation period, is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day evaluation period, your use of the product feature will be governed solely by the Cisco end user license agreement (link above), together with any supplements relating to such product feature. The above applies even if the evaluation license is not automatically terminated and you do not receive any notice of the expiration of the evaluation period. It is your
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring a Cisco Right-To-Use License Configuration Examples for RTU Supported Software Licenses
responsibility to determine when the evaluation period is complete and you are required to make payment to Cisco for your use of the product feature beyond the evaluation period. Your acceptance of this agreement for the software features on one product shall be deemed your acceptance with respect to all such software on all Cisco products you purchase which includes the same software. (The foregoing notwithstanding, you must purchase a license for each software feature you use past the 60 days evaluation period, so that if you enable a software feature on 1000 devices, you must purchase 1000 licenses for use past the 60 day evaluation period.) Activation of the software command line interface will be evidence of your acceptance of this agreement. ACCEPT? (yes/[no]): yes
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring a Cisco Right-To-Use License Configuration Examples for RTU Supported Software Licenses
Use of this product feature requires an additional license from Cisco, together with an additional payment. You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the product, including during the 60 day evaluation period, is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day evaluation period, your use of the product feature will be governed solely by the Cisco end user license agreement (link above), together with any supplements relating to such product feature. The above applies even if the evaluation license is not automatically terminated and you do not receive any notice of the expiration of the evaluation period. It is your responsibility to determine when the evaluation period is complete and you are required to make payment to Cisco for your use of the product feature beyond the evaluation period. Your acceptance of this agreement for the software features on one product shall be deemed your acceptance with respect to all such software on all Cisco products you purchase which includes the same software. (The foregoing notwithstanding, you must purchase a license for each software feature you use past the 60 days evaluation period, so that if you enable a software feature on 1000 devices, you must purchase 1000 licenses for use past the 60 day evaluation period.) Activation of the software command line interface will be evidence of your acceptance of this agreement.
1.0
1.0
1.0
1.0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Evaluation total period: 8 weeks 4 Evaluation period left: 8 weeks 4 Period used: 0 minute 0 second License Count: Non-Counted License Priority: None StoreIndex: 4 Feature: lawful_intr License Type: EvalRightToUse License State: Active, Not in Use, EULA Evaluation total period: 8 weeks 4 Evaluation period left: 8 weeks 4 Period used: 0 minute 0 second License Count: Non-Counted License Priority: None StoreIndex: 5 Feature: sw_redundancy License Type: RightToUse License State: Active, In Use License Count: Non-Counted License Priority: Low StoreIndex: 6 Feature: throughput_10g License Type: EvalRightToUse License State: Active, Not in Use, EULA Evaluation total period: 8 weeks 4 Evaluation period left: 8 weeks 4 Period used: 0 minute 0 second License Count: Non-Counted License Priority: None StoreIndex: 7 Feature: throughput_20g License Type: EvalRightToUse License State: Active, Not in Use, EULA Evaluation total period: 8 weeks 4 Evaluation period left: 8 weeks 4 Period used: 0 minute 0 second License Count: Non-Counted License Priority: None StoreIndex: 8 Feature: throughput_36g License Type: EvalRightToUse License State: Active, Not in Use, EULA Evaluation total period: 8 weeks 4 Evaluation period left: 8 weeks 4 Period used: 0 minute 0 second License Count: Non-Counted License Priority: None
days days
Version: 1.0
Additional References
Related Documents
Related Topic Cisco IOS commands Cisco IOS Software Activation Commands Document Title Cisco IOS Master Commands List, All Releases Cisco IOS Software Activation Command Reference
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
MIBs
MIB
MIBs Link snmp-server view INTERCEPT_VIEW ciscoIpTapMIB snmp-server view INTERCEPT_VIEW cisco802TapMIB snmp-server view INTERCEPT_VIEW ciscoTap2MIB To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Configuring a Cisco Right-To-Use License Feature Information for Cisco RTU License
Note
Table 2 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 2
Feature Information The Cisco ASR 1001 Router and ASR 1002-X Router support technology package-based licenses that are not node locked. In Cisco IOS XE Release 3.7, this feature was introduced on the Cisco ASR 1000 Aggregation Services Routers. The following sections provide information about this feature:
Information About Cisco RTU License, page 2 Configuration Examples for RTU Supported Software Licenses, page 6
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Configuring a Cisco Right-To-Use License Feature Information for Cisco RTU License
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload
First Published: November 28, 2012 Last Updated: July 30, 2013
The deployment of the Intelligent Wireless Access Gateway (iWAG) feature on the Cisco ASR 1000 Series Aggregation Services Routers involves two main technologies: the General Packet Radio Service (GPRS) Tunneling Protocol (GTP) for connecting to the Cisco Gateway GPRS Support Node (Cisco GGSN) and the Mobile Access Gateway (MAG) using Proxy Mobile IPv6 (PMIPv6) for connecting to the Cisco Packet Data Network Gateway (PGW). The integration of these two technologies with the Cisco Intelligent Service Gateway (ISG), in combination with the Service Provider WiFi, is the key concept of the iWAG. The iWAG on the Cisco ASR 1000 Series Aggregation Services Routers provides a clientless solution to integrate with existing 3G mobile cores through Cisco GGSN using the GTP. Leveraging the Cisco ISG framework, the iWAG can selectively divert user traffic towards a mobile network, or offload to the Internet directly. This document provides information about the GTP of the iWAG and its configurations. For more information about PMIPv6 and ISG configurations for the iWAG, see the Intelligent Wireless Access Gateway Configuration Guide, Cisco IOS XE Release 3S.
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Contents
Contents
Overview of the iWAG Deployment, page 2 Restrictions for the GTP of the iWAG, page 3 Information About IP Address Assignment, page 4 Information About Authentication Methods, page 4 Information About GGSN Selection, page 5 How to Configure Authentication, Authorization, and Accounting for the iWAG, page 5 How to Configure DHCP when the iWAG Acts as a DHCP Proxy, page 8 How to Configure the Cisco ISG Class Map and Policy Map for the iWAG, page 10 How to Configure a Subscriber Initiator for the iWAG, page 13 How to Configure a Tunnel Initiator for the iWAG, page 15 How to Enable Mobile Client Service Abstraction and Access Lists, page 17 How to Configure the GTP of the iWAG, page 19 Configuration Examples for the iWAG, page 21 Multiple-Flow Tunnel, page 27 GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers, page 27 iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers, page 30 ISG Policy Templating on the Cisco ASR 1000 Series Aggregation Services Routers, page 32 Additional References, page 33 Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload, page 34
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Restrictions for the GTP of the iWAG
Figure 1 shows a deployment model of the iWAG on a Cisco ASR 1000 Series Aggregation Services Router.
Figure 1 iWAG Deployment on a Cisco ASR 1000 Series Aggregation Services Router
HLR
OCS
PCRF CGF
v GTP
2/S
2a
PGW/LMA
4G Core
Roaming from a 3G mobility network to a WLAN is not supported for the GTP and Cisco ISG sessions. IPv6 and quality of service (QoS) are not supported. Only newly established calls are offloaded to the WLAN Third-Generation Partnership Project (3GPP) IP access. The iWAG solution for WLAN offload is currently available only for the 3G Universal Mobile Telecommunications System (UMTS) and not for 4G Long Term Evolution (LTE).
Note
In Cisco IOS XE Release 3.8S, the iWAG may fail to establish the GTPv1 tunnel with the GGSN, for example, with the Cisco ASR 5000 platform. To address this issue, a workaround that involves prepending 19 to the original MSISDN number was introduced in Cisco IOS XE Release 3.8S. The original issue of the iWAG failing to establish the GTPv1 tunnel with the GGSN is fixed in Cisco IOS XE Release 3.8.1S. Therefore, for customers using Cisco IOS XE Release 3.8.1S and later releases, this workaround is not required. For customers who are using the workaround provided in Cisco IOS XE Release 3.8S, the following commands have been added in the Cisco IOS XE Release 3.8.1S to customize MSISDN encoding:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
360957
Internet
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Information About IP Address Assignment
information-element msisdn [npi npi-value | ton ton-value] radius msisdn leading-digits number of digits
Default gateway Subnet mask and prefix length Domain Name System (DNS) server address Dynamic Host Configuration Protocol (DHCP) server address
802.1x authentication (such as, Extensible Authentication Protocol Method for GSM Subscriber Identity Module (EAP-SIM), and Extensible Authentication Protocol Method for Authentication and Key Agreement (EAP-AKA) Web authentication Media Access Control-Transparent Auto Logon (MAC-TAL) authentication
802.1x Authentication
The 802.1x Authentication method is used in a trusted WiFi network. In this method, the Microsoft client is authenticated before it is assigned an IP address for use.
Web Authentication
The Web authentication method is used in an untrusted WiFi network. In this method, the Microsoft client is authenticated after it is assigned an IP address for use. The iWAG uses the Cisco ISG functionalities in enforcing the Open Garden policy and L4 Redirect to complete the authentication before tunneling a client's session to the corresponding GGSN.
MAC-TAL Authentication
The MAC-TAL authentication method is associated with the Web authentication method in which the Microsoft client tries to reauthenticate after moving from one access point to another access point and attempting to reconnect while the AAA server on which it is authenticated still keeps a record of the clients past results. Thus, when such a reconnect occurs, the iWAG gets an Access Accept message for reauthentication using the clients MAC address as the calling station ID.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Information About GGSN Selection
If a GGSN address is configured in a user profile, the address will have the highest precedence, and will be picked for use. If a GGSN address is not present, but an APN is present in a user profile, the APN will be picked for use. The GTP then sends a DNS query to the DNS servers configured on the box to resolve this name into an address or a list of addresses (when the DNS server performs load balancing). If a list of addresses is received in return, the GTP records this entire list and performs round-robin assignments using this list when establishing new PDP contexts. If both the GGSN address and the APN are not present, the default GGSN address is used. After a GGSN address is picked, it is possible that the picked GGSN is not reachable. If the allowed number of attempts to contact the GGSN fails, the GGSN is considered dead. In such a scenario, further retries with a different GGSN address having higher or lower precedence is not performed. The Microsoft client's PDP context simply fails to establish. If this GGSN address comes from DNS resolution, its entry from the GGSN address list for this APN is removed so that an effort to use the APN will not be made again.
2.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal aaa new-model aaa group server radius group-name server-private ip-address [auth-port port-number | acct-port port-number] [non-standard] [timeout seconds] [retransmit retries] [key string] aaa authentication login {default | list-name} {[passwd-expiry] method1 [method2...]} aaa authorization network authorization-name group server-group name aaa authorization subscriber-service {default {cache | group | local} | list-name} method1 [method2...] aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x} {default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure Authentication, Authorization, and Accounting for the iWAG
12. aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x}
{default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure Authentication, Authorization, and Accounting for the iWAG
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
aaa new-model
Example:
Router(config)# aaa new-model
Step 4
Groups different RADIUS server hosts into distinct lists and distinct methods.
Example:
Router(config)# aaa group server radius AAA_SERVER_CAR
Step 5
server-private ip-address [auth-port port-number | acct-port port-number] [non-standard] [timeout seconds] [retransmit retries] [key string]
Configures the IP address of the private RADIUS server for the group server.
Example:
Router(config-sg-radius)# server-private 5.3.1.76 auth-port 2145 acct-port 2146 key cisco
Step 6
Example:
Router(config-sg-radius)# aaa authentication login default none
Step 7
Example:
Router(config)# aaa authorization network ISG_PROXY_LIST group AAA_SERVER_CAR
Runs authorization for all network-related service requests, including Serial Line Internet Protocol (SLIP), Point-to-Point Protocol (PPP), PPP Network Control Programs (NCPs), and AppleTalk Remote Access (ARA). Specifies one or more AAA authorization methods for the Cisco ISG to provide subscriber service.
Step 8
aaa authorization subscriber-service {default {cache | group | local} | list-name} method1 [method2...]
Example:
Router(config)# aaa authorization subscriber-service default local group AAA_SERVER_CAR
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure DHCP when the iWAG Acts as a DHCP Proxy
Command or Action
Step 9
aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x} {default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name
Purpose Enables AAA of requested services for billing and security purposes when RADIUS or TACACS+ is used.
Example:
Router(config)# aaa accounting network PROXY_TO_CAR
Step 10
Example:
Router(cfg-acct-mlist)# action-type start-stop
Step 11
Example:
Router(cfg-preauth)# group AAA_SERVER_CAR
Step 12
aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x} {default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name
Enables AAA of requested services for billing and security purposes when using RADIUS or TACACS+.
Example:
Router(config)# aaa accounting network ISG_PROXY_LIST start-stop group AAA_SERVER_CAR
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
enable configure terminal ip dhcp excluded-address [vrf vrf-name] ip-address [last-ip-address] ip dhcp pool pool-name network network-number [mask [secondary] | /prefix-length [secondary] default-router ip-address domain-name domain lease {days [hours [minutes]] | infinite}
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure DHCP when the iWAG Acts as a DHCP Proxy
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Specifies the IP address that a DHCP server should not assign to DHCP clients.
Example:
Router(config)# ip dhcp excluded-address 192.168.10.1
Step 4
Configures a DHCP address pool on a DHCP server and enters the DHCP pool configuration mode.
Example:
Router(config)# ip dhcp pool test
Step 5
Example:
Router(dhcp-config)# network 192.168.0.0 255.255.0.0
Configures the network number and mask for a DHCP address pool primary subnet or DHCP address pool secondary subnet on a Cisco IOS DHCP server. Specifies the default router list for a DHCP client.
Step 6
Example:
Router(dhcp-config)# default-router 192.168.10.1
Step 7
domain-name domain
Example:
Router(dhcp-config)# domain-name starent.com
Step 8
Example:
Router(dhcp-config)# lease 1 2 2
Configures the duration of the lease for an IP address that is assigned from a Cisco IOS DHCP server to a DHCP client.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure the Cisco ISG Class Map and Policy Map for the iWAG
How to Configure the Cisco ISG Class Map and Policy Map for the iWAG
This section describes how to configure the Cisco ISG class map and policy map for the iWAG.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal class-map type traffic match-any class-map-name match access-group output {access-group | name access-group-name} match access-group input {access-group | name access-group-name} policy-map type service policy-map-name [priority] class type traffic {class-map-name | default {in-out | input | output}} accounting aaa list aaa-method-list [priority] class type traffic {class-map-name | default {in-out | input | output}}
10. drop 11. policy-map type control policy-map-name 12. class type control {control-class-name | always} [event {access-reject | account-logoff |
account-logon | acct-notification | credit-exhausted | dummy-event | quota-depleted | radius-timeout | service-failed | service-start | service-stop | session-default-service | session-restart | session-service-found | session-start | timed-policy-expiry}]
13. action-number service-policy type service [unapply] [aaa list list-name] {name service-name |
network-service-found {continue | stop}] [use method authorization-type] identifier identifier-type [plus identifier-type]
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure the Cisco ISG Class Map and Policy Map for the iWAG
Command or Action
Step 3
class-map type traffic match-any class-map-name
Purpose Creates or modifies a traffic class map that is used for matching packets to a specified Cisco ISG traffic class.
Example:
Router(config)# class-map type traffic match-any TC_OPENGARDEN
Step 4
Configures the match criteria for a Cisco ISG traffic class map on the basis of the specified access control list (ACL).
Example:
Router(config-traffic-classmap)# match access-group output name ACL_OUT_OPENGARDEN
Step 5
Configures the match criteria for a Cisco ISG traffic class map on the basis of the specified ACL.
Example:
Router(config-traffic-classmap)# match access-group input name ACL_IN_OPENGARDEN
Step 6
Creates or modifies a service policy map that is used to define a Cisco ISG subscriber service.
Example:
Router(config)# policy-map type service OPENGARDEN_SERVICE
Step 7
Creates or modifies a traffic class map that is used for matching packets to a specified Cisco ISG traffic class.
Example:
Router(config-service-policymap)# 20 class type traffic TC_OPENGARDEN
Step 8
Example:
Router(config-service-policymap)# accounting aaa list PROXY_TO_CAR
Enables Cisco ISG accounting and specifies an AAA method list to which accounting updates are forwarded.
Step 9
Creates or modifies a traffic class map that is used for matching packets to a specified Cisco ISG traffic class.
Example:
Router(config-service-policymap)# class type traffic default in-out
Step 10
drop
Configures a Cisco ISG to discard packets belonging to the default traffic class.
Example:
Router(config-service-policymap)# drop
Step 11
Creates or modifies a control policy map that defines a Cisco ISG control policy.
Example:
Router(config)# policy-map type control BB_PROFILE
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure the Cisco ISG Class Map and Policy Map for the iWAG
Command or Action
Step 12
class type control {control-class-name | always} [event {access-reject | account-logoff | account-logon | acct-notification | credit-exhausted | dummy-event | quota-depleted | radius-timeout | service-failed | service-start | service-stop | session-default-service | session-restart | session-service-found | session-start | timed-policy-expiry}]
Purpose Specifies a control class for which actions can be configured in a Cisco ISG control policy.
Example:
Router (config-control-policymap)# class type control always event session-start
Step 13
action-number service-policy type service [unapply] [aaa list list-name] {name service-name | identifier {authenticated-domain | authenticated-username | dnis | nas-port | tunnel-name | unauthenticated-domain | unauthenticated-username}}
Example:
Router(config-control-policymap-class-control)# 10 service-policy type service name OPENGARDEN_SERVICE
Step 14
action-number authorize [aaa {list-name | list {list-name | default}} [password password]] [upon network-service-found {continue | stop}] [use method authorization-type] identifier identifier-type [plus identifier-type]
Initiates a request for authorization based on a specified identifier in a Cisco ISG control policy.
Example:
Router(config-control-policymap-class-control)# 20 authorize aaa list ISG_PROXY_LIST password cisco identifier mac-address
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure a Subscriber Initiator for the iWAG
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal interface GigabitEthernet slot/subslot/port description string ip address ip-address mask [secondary [vrf vrf-name]] negotiation auto service-policy type control policy-map-name ip subscriber {l2-connected | routed} initiator {dhcp [class-aware] | radius-proxy | static ip subscriber list listname | unclassified ip | unclassified mac} unclassified mac}
10. initiator {dhcp [class-aware] | radius-proxy | static ip subscriber list listname | unclassified ip |
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure a Subscriber Initiator for the iWAG
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# interface GigabitEthernet 1/3/3
Step 4
description string
Example:
Router(config-if)# description access interface connected to subscriber
Step 5
Example:
Router(config-if)# ip address 192.171.10.1 255.255.0.0
Step 6
negotiation auto
Example:
Router(config-if)# negotiation auto
Step 7
Example:
Router(config-if)# service-policy type control BB_Profile
Step 8
Example:
Router(config-if)# ip subscriber l2-connected
Enables Cisco ISG IP subscriber support on an interface and specifies the access method that IP subscribers use for connecting to the Cisco ISG on an interface.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure a Tunnel Initiator for the iWAG
Command or Action
Step 9
initiator {dhcp [class-aware] | radius-proxy | static ip subscriber list listname | unclassified ip | unclassified mac-address}
Purpose Enables Cisco ISG to create an IP subscriber session upon receipt of a specified type of packet.
Example:
Router(config-subscriber)# initiator unclassified mac-address
Step 10
initiator {dhcp [class-aware] | radius-proxy | static ip subscriber list listname | unclassified ip | unclassified mac-address}
Enables Cisco ISG to create an IP subscriber session upon receipt of a specified type of packet.
Example:
Router(config-subscriber)# initiator dhcp
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
enable configure terminal interface GigabitEthernet slot/subslot/port description string ip address ip-address mask [secondary [vrf vrf-name]] negotiation auto
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# interface GigabitEthernet 1/3/5
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure a Tunnel Initiator for the iWAG
Command or Action
Step 4
description string
Example:
Router(config-if)# description interface connected to GGSN
Step 5
Example:
Router(config-if)# ip address 192.170.10.1 255.255.0.0
Step 6
negotiation auto
Example:
Router(config-if)# negotiation auto
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Enable Mobile Client Service Abstraction and Access Lists
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal mcsa enable sessionmgr ip access-list {{standard | extended} {access-list-name | access-list-number} | helper egress check} permit ip any any permit udp any any ip access-list {{standard | extended} {access-list-name | access-list-number} | helper egress check} permit ip any any
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Enable Mobile Client Service Abstraction and Access Lists
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
mcsa
Example:
Router(config)# mcsa
Enables mobile client service abstraction on the Cisco ASR 1000 Series Aggregation Services Routers. Enables mobile client service abstraction to receive notifications from the Cisco ISG.
Step 4
enable sessionmgr
Example:
Router(config-mcsa)# enable sessionmgr
Step 5
Defines an IP access list by name or number, or enables filtering for packets with IP helper address destinations.
Example:
Router(config)# ip access-list extended ACL_IN_OPENGARDEN
Step 6
Example:
Router(config-ext-nacl)# permit ip any any
Step 7
Example:
Router(config-ext-nacl)# permit udp any any
Step 8
Defines an IP access list by name or number, or enables filtering for packets with IP helper-address destinations.
Example:
Router(config)# ip access-list extended ACL_OUT_OPENGARDEN
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure the GTP of the iWAG
Command or Action
Step 9
permit ip any any
Example:
Router(config-ext-nacl)# permit ip any any
Step 10
Example:
Router(config-ext-nacl)# permit udp any any
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal gtp n3-request request-number interval t3-response response-number interval echo-request request-number interface local GigabitEthernet slot/subslot/port apn apn-name ip address ggsn ip-address
10. default-gw address prefix-len value 11. dns-server ip-address 12. dhcp-server ip-address 13. dhcp-lease seconds
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload How to Configure the GTP of the iWAG
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
gtp
Configures the GTP for the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers.
Example:
Router(config)# gtp
Step 4
Example:
Router(config-gtp)# n3-request 3
Specifies the number of times a control message must be retried before a failure is issued. The default value is 5. Specifies the time interval, in seconds, for which the Serving GPRS Support Node (SGSN) of the iWAG waits for a response for the control message sent. The default value is 1. Specifies the time interval, in seconds, for which the SGSN for the iWAG waits for before sending an echo request message. The range is from 60 to 65535. The default value is 60. The value of 0 disables the Echo Request feature. Configures the transport interface to communicate with the GGSN.
Step 5
Example:
Router(config-gtp)# interval t3-response 10
Step 6
Example:
Router(config-gtp)# interval echo-request 60
Step 7
Example:
Router(config-gtp)# interface local GigabitEthernet 0/0/3
Step 8
apn apn-name
Example:
Router(config-gtp)# apn starent.com
Configures an ASCII regular expression string to be matched against the APN for general packet radio service (GPRS) load balancing. Sets the IP address for the GGSN.
Step 9
Example:
Router(config-gtp-apn)# ip address ggsn 192.170.10.2
Step 10
Example:
Router(config-gtp-apn)# default-gw 192.171.10.1 prefix-len 16
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
Command or Action
Step 11
dns-server ip-address
Purpose Specifies the Domain Name System (DNS) IP servers that are available for a DHCP client.
Example:
Router(config-gtp-apn)# dns-server 192.165.1.1
Step 12
dhcp-server ip-address
Example:
Router(config-gtp-apn)# dhcp-server 192.168.10.1
Specifies primary and backup DHCP servers to allocate IP addresses to mobile station users entering a particular public data network (PDN) access point. Configures the duration of the lease for an IP address that is assigned from a Cisco IOS DHCP Server to a DHCP client.
Step 13
dhcp-lease seconds
Example:
Router(config-gtp-apn)# dhcp-lease 3000
Example: Configuring the iWAG Using the TAL Authentication Method, page 21 Example: Configuring the iWAG Using the EAP-SIM Authentication Method, page 23 Example: Configuring the iWAG Using the Web Logon Authentication Method, page 25
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
! class-map type traffic match-any TC_OPENGARDEN match access-group output name ACL_OUT_OPENGARDEN match access-group input name ACL_IN_OPENGARDEN ! policy-map type service OPENGARDEN_SERVICE 20 class type traffic TC_OPENGARDEN accounting aaa list PROXY_TO_CAR ! class type traffic default in-out drop ! ! policy-map type control BB_PROFILE class type control always event session-start 10 service-policy type service name OPENGARDEN_SERVICE 20 authorize aaa list ISG_PROXY_LIST password cisco identifier mac-address ! ! interface GigabitEthernet1/3/3 descriptions interface connected to LS-IP APP Node ip address 192.171.10.1 255.255.0.0 negotiation auto service-policy type control BB_PROFILE ip subscriber l2-connected initiator unclassified mac-address initiator dhcp ! interface GigabitEthernet1/3/5 descriptions connected to LS-GGSN ip address 192.170.10.1 255.255.0.0 negotiation auto ! mcsa enable sessionmgr ! ! ip access-list extended ACL_IN_OPENGARDEN permit ip any any permit udp any any ip access-list extended ACL_OUT_OPENGARDEN permit ip any any permit udp any any ! ! gtp n3-request 3 interval t3-response 10 interval echo-request 60 interface local GigabitEthernet0/0/3 apn 1 apn-name starent.com ip address ggsn 192.170.10.2 default-gw 192.168.10.1 prefix-len 16 dns-server 192.165.1.1 dhcp-server 192.168.10.1 dhcp-lease 30000 ! End
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
interface GigabitEthernet1/3/3 description connected to subscriber ip address 192.171.10.1 255.255.0.0 negotiation auto service-policy type control BB_PROFILE ip subscriber l2-connected initiator dhcp initiator radius-proxy ! interface GigabitEthernet1/3/4 description interface connected to AAA server ip address 192.171.10.1 255.255.0.0 negotiation auto ! interface GigabitEthernet1/3/5 description connected to GGSN ip address 192.170.10.1 255.255.0.0 negotiation auto ! ! mcsa enable sessionmgr ! ip access-list extended ACL_IN_OPENGARDEN permit ip any any permit udp any any ip access-list extended ACL_OUT_OPENGARDEN permit ip any any permit udp any any ! radius-server attribute 44 include-in-access-req default-vrf radius-server attribute 44 extend-with-addr radius-server attribute 8 include-in-access-req radius-server attribute 32 include-in-access-req radius-server attribute 32 include-in-accounting-req radius-server attribute 55 include-in-acct-req radius-server attribute 55 access-request include radius-server attribute 31 send nas-port-detail radius-server source-ports extended radius-server throttle accounting 50 radius-server unique-ident 49 radius-server vsa send accounting radius-server vsa send authentication ! ! gtp n3-request 3 interval t3-response 10 interval echo-request 60 information-element rat-type wlan interface local GigabitEthernet0/0/3 apn 1 apn-name starent.com ip address ggsn 192.170.10.2 default-gw 192.168.10.1 prefix-len 16 dns-server 192.165.1.1 dhcp-server 192.168.10.1 ! End
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
Example: Configuring the iWAG Using the Web Logon Authentication Method
The following example shows how to configure the iWAG using the Web logon authentication method:
aaa new-model ! ! aaa group server radius AAA_SERVER_CAR server-private 5.3.1.76 auth-port 2145 acct-port 2146 key cisco ! aaa authentication login default none aaa authentication login ISG_PROXY_LIST group AAA_SERVER_CAR aaa authorization network ISG_PROXY_LIST group AAA_SERVER_CAR aaa authorization subscriber-service default local group AAA_SERVER_CAR aaa accounting network PROXY_TO_CAR action-type start-stop group AAA_SERVER_CAR ! aaa accounting network ISG_PROXY_LIST start-stop group AAA_SERVER_CAR ! aaa server radius dynamic-author client 5.3.1.76 server-key cisco auth-type any ignore server-key ! ip dhcp excluded-address 192.168.10.1 ip dhcp excluded-address 192.168.10.2 ip dhcp excluded-address 192.168.10.3 ! ip dhcp pool TEST network 192.168.0.0 255.255.0.0 default-router 192.168.10.1 domain-name starent.com lease 1 2 2 ! ! redirect server-group REDIRECT-SERVER-GROUP1 server ip 5.3.1.76 port 10080 ! ! ip tftp source-interface GigabitEthernet0 class-map type traffic match-any TC_L4R_class match access-group input name TC_L4R ! class-map type traffic match-any TC_OPENGARDEN match access-group output name ACL_OUT_OPENGARDEN match access-group input name ACL_IN_OPENGARDEN ! policy-map type service OPENGARDEN_SERVICE 20 class type traffic TC_OPENGARDEN accounting aaa list PROXY_TO_CAR ! class type traffic default in-out drop ! ! policy-map type service L4Redirect_service 10 class type traffic TC_L4R_class redirect to group REDIRECT-SERVER-GROUP1 ! ! policy-map type control BB_PROFILE class type control always event session-start
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
25
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Configuration Examples for the iWAG
10 service-policy type service name L4Redirect_service 20 service-policy type service name OPENGARDEN_SERVICE ! class type control always event account-logon 10 authenticate aaa list ISG_PROXY_LIST 20 service-policy type service unapply name L4Redirect_service ! ! interface GigabitEthernet1/3/3 description interface connected to subscriber ip address 192.171.10.1 255.255.0.0 negotiation auto service-policy type control BB_PROFILE ip subscriber l2-connected initiator unclassified mac-address initiator dhcp ! ! interface GigabitEthernet1/3/5 descriptions interface connected to GGSN ip address 192.170.10.1 255.255.0.0 negotiation auto ! ! mcsa enable sessionmgr ! ! ip access-list extended ACL_IN_OPENGARDEN permit ip any any permit udp any any ip access-list extended ACL_OUT_OPENGARDEN permit ip any any permit udp any any ip access-list extended TC_L4R permit udp any any permit tcp any any ! ! radius-server attribute 44 include-in-access-req default-vrf radius-server attribute 8 include-in-access-req radius-server attribute 32 include-in-access-req radius-server attribute 32 include-in-accounting-req radius-server attribute 55 include-in-acct-req radius-server attribute 55 access-request include no radius-server attribute nas-port radius-server source-ports extended radius-server unique-ident 73 ! gtp n3-request 3 interval t3-response 10 interval echo-request 60 information-element rat-type wlan interface local GigabitEthernet 0/0/3 apn 1 apn-name starent.com ip address ggsn 192.170.10.2 default-gw 192.168.10.1 prefix-len 16 dns-server 192.165.1.1 dhcp-server 192.168.10.1 dhcp-lease 30000 ! End
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
26
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Multiple-Flow Tunnel
Multiple-Flow Tunnel
A tunnel facilitates bidirectional transport or acts as a conduit for forwarding subscriber traffic. In PMIPv6, subscriber traffic is transported between the MAG and the Local Mobility Anchor (LMA) through the Generic Routing Encapsulation (GRE) tunnel. In the GTP, subscriber traffic is transported between the iWAG and the GGSN through the GTP tunnel. The tunnel information structure is associated with each tunnel and specifies common tunnel attributes, such as source address, destination address, protocol, port, key, tunnel transport VRF, and tunnel mode. Both the GTP and PMIPv6 support multiple flows per tunnel. A multiple-flow tunnel mechanism configures and manages multiple flows of traffic within the same tunnel. Each flow is identified by a flow key. A flow identifier or flow key is a 32-bit integer. The key is globally unique per system for the GTP. However, the key can be unique per tunnel for PMIPv6. The flow key for the GTP is the Tunnel Endpoint Identifier (TEID), and for PMIPv6, it is the GRE key. Each flow has parameters to describe the per-flow attributes. PMIPv6 uses a multipoint GRE tunnel per LMA, and creates one adjacency per flow. An LMA can support scaling numbers up to 128,000 MAG. From the LMA perspective, only one multipoint GRE tunnel interface is created and 128,000 tunnel endpoints are populated. This scaling level supports the MAG functionality that is implemented on access points or hotspots, from which only one or few PMIPv6 subscribers can be attached. Cisco high-end routing platforms, such as the Cisco ASR 1000 Series Route Processor 2, the Cisco ASR 1000 Series 40-Gbps ESP, and the Cisco ASR 1000 Series 100-Gbps ESP support 128,000 scaling for the LMA. To support 128,000 scaling, configure the following on the LMA:
ipv6 mobile pmipv6-lma LMA1 domain D1 bce maximum 128000
GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers
Effective from Cisco IOS XE Release 3.10S, the support for GPRS Tunneling Protocol Version 2 (GTPv2) is offered on the Cisco ASR 1000 Series Aggregation Services Routers as an enhancement to the GTPv1 offering in the iWAG solution that was introduced in Cisco IOS XE Release 3.8S. GTPv2 provides support for both the 4G and 3G mobile users, whereas GTPv1 provides support only for 3G mobile users. A GTP session with GTPv2 support uses more memory than a GTP session with GTPv1 support. GTPv2 support does not require any new AAA attributes. However, the new gtpv2 enum value for the Cisco-MPC-Protocol-Interface attribute is necessary to specify the use of GTPv2. The AAA server identifies a subscriber depending upon whether the subscriber profile is sent over GTPv1 tunnel or GTPv2 tunnel from the iWAG back to the Evolved Packet Core (EPC). The GTPv1 and GTPv2 sessions can exist simultaneously on the iWAG.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
27
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers
gtp n3-request 7 interval t3-response 1 interval echo-request 64 information-element rat-type wlan interface local GigabitEthernet1/3/0 apn 1 apn-name example.com #Same donamin name as apn2356, not supported, should be different ip address ggsn 98.0.7.13 default-gw 192.168.0.1 prefix-len 16 dns-server 192.168.255.253 dhcp-lease 3000 apn 2356 apn-name example.com #Same domain name as apn1, not supported, should be different ip address ggsn 98.0.7.14 default-gw 10.254.0.1 prefix-len 16 dns-server 10.254.255.253 dhcp-lease 3000 !
The same domain name cannot be configured in different APNs, for example:
The same pool cannot be associated with different APNs. The PGW or GGSN must have different IPs for pools configured on different domains, for example:
Example:
gtp n3-request 7 interval t3-response 1 interval echo-request 64 information-element rat-type wlan interface local GigabitEthernet1/3/0 apn 1 apn-name example.com ip address ggsn 98.0.7.13 default-gw 192.168.0.1 prefix-len 16 #different domain name but same pool ip; this is not supported dns-server 192.168.255.253 dhcp-lease 3000 apn 2356 apn-name example.com #Same domain name as apn1, not supported, should be different ip address ggsn 98.0.7.14 default-gw 192.168.0.1 prefix-len 16 #different domain name but same pool ip; this is not supported dns-server 10.254.255.253 dhcp-lease 3000 !
GTPv2 Configuration
All the configurations required for GTPv1 support are also needed for GTPv2 support.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
28
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers
RADIUS Configuration
The following configurations are required on the RADIUS server to differentiate between a GTPv1 subscriber and a GTPv2 subscriber:
subscriber-profile profile1 { # this is a GTPv2 profile access-accept { reply-msg "Default profile" cisco-avpair { "cisco-mn-service=ipv4" } cisco-avpair { "cisco-mpc-protocol-interface=gtpv2" } cisco-avpair { "cisco-service-selection=example.com" } cisco-avpair { "cisco-msisdn=4910000000" } 3gpp { imsi 406091000000000 } } } subscriber-profile profile2 { # this is a GTPv1 profile access-accept { reply-msg "Default profile" cisco-avpair { "cisco-mn-service=ipv4" } cisco-avpair { "cisco-mpc-protocol-interface=gtpv1" } cisco-avpair { "cisco-service-selection=example.com" } cisco-avpair { "cisco-msisdn=4900000000" } 3gpp { imsi 406090000000000 } } } sub-grp-mgr sub-grp1 { control-by round-robin group-profiles { subscriber-profile profile1 profile-priority 99 subscriber-profile profile2 profile-priority 98 } }
Intra-iWAG Roaming
Effective from Cisco IOS XE Release 3.10S, both GTPv1 and GTPv2 support connected subscriber roaming across different access interfaces of the iWAG. GTPv1 and GTPv2 preserve and update their existing sessions to allow their data traffic to flow through the new ingress interfaces from the access network.
Configuration for the GTPv1 and GTPv2 Roaming Scenario
The initiator unclassified mac-address command must be configured on every iWAG access interface to support subscriber roaming between these interfaces. As shown in the following configuration, all the access interfaces must be specified under the GTP configuration before bringing up the IP subscriber sessions. If the access interface is not specified under the GTP, a subscribers roaming option is not enabled for that interface. Also, adding interfaces under the GTP after the sessions bring up fails subscriber roaming. The following example shows the configuration for GTPv1 and GTPv2 roaming scenario:
interface GigabitEthernet0/0/2 description To client facing interface ip address 192.1.1.1 255.255.0.0 negotiation auto service-policy type control ISG_GTP_CONTROL ip subscriber l2-connected
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
29
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers
initiator unclassified mac-address # must for roaming config initiator dhcp ! interface GigabitEthernet0/0/3 description To client facing interface ip address 192.2.1.1 255.255.0.0 negotiation auto service-policy type control ISG_GTP_CONTROL ip subscriber l2-connected initiator unclassified mac-address # must for roaming config initiator dhcp ! gtp n3-request 3 interval t3-response 10 interval echo-request 64 information-element rat-type wlan interface local GigabitEthernet1/3/0 apn 1200 apn-name example.com ip address ggsn 98.0.7.13 default-gw 192.168.0.1 prefix-len 16 dns-server 192.168.255.253 dhcp-lease 3000 interface access GigabitEthernet0/0/2 interface access GigabitEthernet0/0/3
iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers
Effective from Cisco IOS XE Release 3.10S, the per-session Stateful Switchover (SSO)/In Service Software Upgrade (ISSU) feature supports iWAG mobility sessions that are tunneled to MNO using GTP. The SSO feature takes advantage of Route Processor (RP) redundancy by establishing one of the RPs as the active processor, while the other RP is designated as the standby processor, and then synchronizing the critical state information between them. When a failover occurs, the standby device seamlessly takes over, starts performing traffic-forwarding services, and maintains a dynamic routing table. The SSO/ISSU feature supports only the Cisco ASR 1000 Series Aggregation Services Routers intrachassis (RP-to-RP) SSO, but not the interchassis (Cisco ASR1K-to-Cisco ASR1K) SSO. The First Sign Of Life (FSOL) triggers that are supported on SSO include DHCP proxy (where the iWAG acts as the DHCP proxy server) and DHCP proxy plus unclassified MAC. For more information about ISSU, see the Overview of ISSU on the Cisco ASR 1000 Series Routers section of the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide. The process as part of iWAG SSO handling GTP checkpoints to the standby RP the information that is necessary to create a copy of the session on the standby RP. Such an inactive copy of the session becomes active when the standby RP becomes active. When an iWAG mobility session with GTP tunneling is enabled using the SSO/ISSU, Cluster Control Manager on the active RP needs to wait for a few more components, including the GTP, to become ready before checkpoint data collection, and polls these additional components for checkpoint data during data collection. A very similar operation is performed on the standby RP as well. Although such additional CPU consumption is per session, it is not expected to be too heavy since processing in each of these components should include the time spent on a few data structure lookups and memory-copying operations.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
30
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers
During ISSU SIP and SPA upgrade, there is traffic interruption. To avoid session disconnect because of dropped echo messages during such traffic interruption, a user has the following options:
Option 1 (preferred):
1. 2.
Disable the echo messages on the iWAG and GGSN for the duration of the ISSU. Re-enable the echo messages after ISSU is completed on the iWAG and GGSN.
Option 2: Extend the t3 and n3 configurations to exceed the expected traffic interruption. The traffic interruption characterized in the Cisco IOS XE Release 3.10S is 127 seconds. Hence, we recommend the following t3 and n3 settings (t3_response: 1 and n3_request: 7, resulting in 127 seconds on both the iWAG and GGSN) but the duration of the traffic interruption may depend on the types of SIPs and SPAs and how loaded the router is. If traffic interruption exceeds the configured t3 and n3 limits, the session is disconnected.
SUMMARY STEPS
1. 2. 3. 4.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
31
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload ISG Policy Templating on the Cisco ASR 1000 Series Aggregation Services Routers
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
redundancy
Example:
Router(config)# redundancy
Step 4
mode SSO
Example:
Router(config-redundan)# mode SSO
ISG Policy Templating on the Cisco ASR 1000 Series Aggregation Services Routers
In Cisco IOS XE Release 3.10S, the Intelligent Services Gateway (ISG) Policy Templating feature optimizes the provisioning of ISG policies on IPv4 and IPv6 subscriber sessions. It enables support of up to 128,000 IP subscriber sessions with more complex ISG policies at a higher churn rate on the Cisco ASR 1000 Series Aggregation Services Routers. The optimization takes advantage of the fact that a typical ISG configuration has very few distinct policies and many sessions with these policies. Instead of provisioning an ISG policy with all its individual services and features on each target IP subscriber session, it provisions a template of the policy through the system only once and references the template after that to apply the policy on each target session. Enabling policy templates in the ISG does not impact session SSO.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
32
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Additional References
Note
The platform subscriber template command does not take effect until the router is reloaded. For example, if this command is entered at the configuration prompt, policy templating remains disabled until the router is reloaded. Similarly, if templating is enabled, the router has to be reloaded after the no subscriber template command is entered to disable ISG policy templating.
Additional References
The following sections provide references related to the iWAG feature.
Related Documents
Related Topic Cisco IOS commands Intelligent Services Gateway Cisco IOS Configuration Fundamentals Document Title Cisco IOS Master Commands List, All Releases Intelligent Services Gateway Configuration Guide, Cisco IOS XE Release 3S Cisco IOS Configuration Fundamentals Command Reference
Standards
Standard No new or modified standards are supported by this feature. Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use the Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
RFCs
RFC1 RFC 5213 RFC 5844 RFC 5845 Title Proxy Mobile IPv6 IPv4 Support for Proxy Mobile IPv6 Generic Routing Encapsulation (GRE) Key Option for Proxy Mobile IPv6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
33
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload
Table 1 lists the features in this module and provides links to specific configuration information. Only features that were introduced or modified in Cisco IOS Release 3.8.0S or a later release appear in the table. Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the corresponding command reference documentation. Use the Cisco Feature Navigator to find information about platform support and software image support. The Cisco Feature Navigator enables you to determine which Cisco IOS and Cisco Catalyst operating system software images support a specific software release, feature set, or platform. To access the Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 1 Feature Information for the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers
Feature Name
Releases
Feature Information In Cisco IOS XE Release 3.10S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. For information on this feature, see the GTP Version 2 in the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers section on page 27.
GTP Version 2 in the iWAG on the Cisco ASR 3.10S 1000 Series Aggregation Services Routers
iWAG SSO Support for GTP on the Cisco ASR 3.10S 1000 Series Aggregation Services Routers
In Cisco IOS XE Release 3.10S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. For information on this feature, see the iWAG SSO Support for GTP on the Cisco ASR 1000 Series Aggregation Services Routers section on page 30.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
34
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload
Table 1
Feature Information for the iWAG on the Cisco ASR 1000 Series Aggregation Services Routers (continued)
Feature Name
Releases
Feature Information In Cisco IOS XE Release 3.10S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. For information on this feature, see the ISG Policy Templating on the Cisco ASR 1000 Series Aggregation Services Routers section on page 32.
ISG Policy Templating on the Cisco ASR 1000 3.10S Series Aggregation Services Routers
3.9S
In Cisco IOS XE Release 3.9S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. For information on this feature, see Multiple-Flow Tunnel section on page 27.
iWAG on the Cisco ASR 1000 Series Aggregation Services Routers for Service Provider WiFi Offload
3.8S
The iWAG deployment involves two main technologies: GTP for connecting to the Cisco GGSN and MAG using PMIPv6 for connecting to the Cisco PGW. The integration of these two technologies with Cisco ISG in combination with service provider WiFi is the key concept of the iWAG feature. In Cisco IOS XE Release 3.8S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 2012-2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
35
iWAG on Cisco ASR 1000 Series Routers for Service Provider WiFi Offload Feature Information for the iWAG on the Cisco ASR 1000 Series Routers for Service Provider WiFi Offload
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
36
This document describes how to configure the UniDirectional Link Detection (UDLD) protocol on the Cisco ASR 1000 Series Aggregation Services Routers.
Contents
Restrictions for the UDLD Protocol, page 2 Information About the UDLD Protocol, page 2 How to Configure the UDLD Protocol, page 4 Configuration Examples for UDLD Protocol, page 10 Additional References, page 12 Feature Information for Configuring UDLD on Cisco ASR 1000 Series Aggregation Services Routers, page 14
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
UniDirectional Link Detection (UDLD) Protocol Restrictions for the UDLD Protocol
High Availability (HA) is not supported, but when the Ethernet port is up and UDLD is enabled on the port, the UDLD automatically performs the detection. Only Gigabit Ethernet, 10 Gigabit Ethernet, and Fast Ethernet interfaces are supported. Supports only the basic UDLD functions.
UDLD Overview, page 2 Configuring the UDLD Aggressive Mode, page 3 Default UDLD Configuration, page 3
UDLD Overview
The Cisco-proprietary UDLD protocol allows the devices connected through fiber optic or copper (for example, Category 5 cabling) Ethernet cables that are connected to the LAN ports to monitor the physical configuration of the cables and detect whether a unidirectional link exists. When a unidirectional link is detected, the UDLD shuts down the affected LAN port and alerts the corresponding user, because unidirectional links cause a variety of problems, including spanning tree topology loops. UDLD is a Layer 2 protocol that works with the Layer 1 protocols to determine the physical status of a link. In Layer 1, auto negotiation takes care of physical signaling and fault detection. UDLD performs tasks that auto negotiation cannot perform, such as detecting the identities of neighbors and shutting down misconnected LAN ports. When you enable both auto negotiation and UDLD, the Layer 1 and Layer 2 detections work together to prevent physical and logical unidirectional connections and the malfunctioning of other protocols. A unidirectional link occurs whenever the traffic transmitted by a local device over a link is received by a neighbor, but traffic transmitted from the neighbor is not received by the local device. If one of the fiber strands in a pair is disconnected, the link does not stay up as long as the auto negotiation is active. In such a scenario, the logical link is undetermined, and the UDLD does not take any action. If both the fibers are working normally in Layer 1, the UDLD in Layer 2 determines whether those fibers are connected correctly and whether the traffic is flowing bidirectionally between the correct neighbors. This check cannot be performed by auto negotiation because auto negotiation operates in Layer 1. The Cisco ASR 1000 Series Aggregation Services Routers periodically transmit the UDLD packets to the neighbor devices on LAN ports where UDLD is enabled. If the packets are echoed back within a specific timeframe and they are lacking a specific acknowledgment (echo), the link is flagged as unidirectional and the LAN port is shut down. Devices on both ends of the link must support UDLD for the protocol to successfully identify and disable the unidirectional links.
Note
By default, the UDLD is disabled on all ports to avoid sending unnecessary traffic.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol Information About the UDLD Protocol
Figure 1-1 shows an example of a unidirectional link condition. Switch B successfully receives traffic from Switch A on the port. However, Switch A does not receive traffic from Switch B on the same port. UDLD detects the problem and disables the port.
Figure 1-1 Unidirectional Link
Switch A TX RX
TX
RX
18720
Switch B
One side of a link has a port (either Tx and Rx) stuck. One side of a link remains up while the other side of the link has gone down.
Feature UDLD global enable state UDLD aggressive mode UDLD per-port enable state for twisted-pair (copper) media
Default Value Globally disabled Disabled Disabled on all Ethernet 10/100 and 1000BASE-TX LAN ports
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
Enabling UDLD Globally, page 4 Enabling UDLD on Individual LAN Interfaces, page 4 Disabling UDLD on Fiber-Optic LAN Interfaces, page 6 Configuring the UDLD Probe Message Interval, page 7 Resetting the Disabled LAN Interfaces Manually, page 8 Resetting the Disabled LAN Interfaces Automatically, page 8 Debugging UDLD, page 9
SUMMARY STEPS
1. 2. 3.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router# enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# udld enable
This command configures only the fiber-optic LAN ports. Individual LAN port configuration overrides the setting of this command.
Use the no form of this command to disable the UDLD globally on fiber-optic LAN ports.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
SUMMARY STEPS
1. 2. 3. 4.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# interface gigabitethernet2/2
Step 4
Example:
Router(config)# udld port aggressive
Enables UDLD on a specific LAN port. Enter the aggressive keyword to enable the aggressive mode. On a fiber-optic LAN port, this command overrides the udld enable global configuration command setting. Use the no form of this command to disable the UDLD on a nonfiber-optic LAN port. On fiber-optic LAN ports, the no udld port command reverts the LAN port configuration to the udld enable global configuration command setting.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
SUMMARY STEPS
1. 2. 3. 4.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# interface gigabitethernet2/2
Step 4
Disables UDLD on a fiber-optic LAN port. Use the no form of this command to revert to the udld enable global configuration command setting.
Example:
Router(config)# udld port disable
Note
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
SUMMARY STEPS
1. 2. 3.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# udld message time 60
Configures the time between the UDLD probe messages on the ports that are in the advertisement mode and are currently determined to be bidirectional. Valid values are from 7 to 90 seconds. Use the no form of this command to return to the default value (15 seconds).
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
SUMMARY STEPS
1. 2.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
udld reset
Resets all the LAN ports that have been shut down by UDLD.
Example:
Router# udld reset
SUMMARY STEPS
1. 2. 3. 4.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol How to Configure the UDLD Protocol
Command
Step 3
udld recovery no udld recovery
Purpose Enables the recovery timer for the UDLD error disabled state. Use the no form of this command to disable the recovery timer for the UDLD error disabled state. Specifies the time to recover from a UDLD error disabled state. Valid values are from 30 to 86400 seconds. Use the no form of this command to return to the default value (300 seconds).
Example:
Router(config)# udld recovery
Step 4
Example:
Router(config)# udld recovery interval 100
Debugging UDLD
To enable the debugging of an UDLD activity, perform this task:
SUMMARY STEPS
1. 2.
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
debug udld {events | packets | registries} no debug udld {events | packets | registries}
Enables the debugging of UDLD process events, packets, or registry events. Use the no form of this command to disable the debugging of UDLD process events, packets, or registry events.
Example:
Router# debug udld events
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
UniDirectional Link Detection (UDLD) Protocol Configuration Examples for UDLD Protocol
-------- ------------------------------ ------------ ------- -------------Gi3/1 Gi4/1 SAL0734K5R2 SAL0734K5R2 1 1 Gi4/1 Gi3/1 Bidirectional Bidirectional
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
UniDirectional Link Detection (UDLD) Protocol Configuration Examples for UDLD Protocol
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Additional References
The following sections provide references related to the UniDirectional Link Detection (UDLD) protocol on the Cisco ASR 1000 Series Aggregation Services Routers.
Related Documents
Related Topic Cisco IOS commands Cisco IOS Configuration Fundamentals Document Title Cisco IOS Master Commands List, All Releases Cisco IOS Configuration Fundamentals Command Reference
Standards
Standard No new or modified standards are supported by this feature. Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use the Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
RFCs
RFC1 RFC 5171
1. Not all the supported RFCs are listed.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
UniDirectional Link Detection (UDLD) Protocol Feature Information for Configuring UDLD on Cisco ASR 1000 Series Aggregation Services Routers
Feature Information for Configuring UDLD on Cisco ASR 1000 Series Aggregation Services Routers
Table 2 lists the features in this module and provides links to specific configuration information. Only features that were introduced or modified in Cisco IOS Release 3.9S or later appear in the table. Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the corresponding command reference documentation. Use the Cisco Feature Navigator to find information about platform support and software image support. The Cisco Feature Navigator enables you to determine which Cisco IOS and Cisco Catalyst operating system software images support a specific software release, feature set, or platform. To access the Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 2 Feature Information for Configuring UDLD on Cisco ASR 1000 Series Aggregation Services Routers
Releases 3.9S
Feature Information The Cisco-proprietary UDLD protocol allows devices connected through fiber-optic or copper (for example, Category 5 cabling) Ethernet cables connected to LAN ports to monitor the physical configuration of the cables and detect when a unidirectional link exists. When a unidirectional link is detected, UDLD shuts down the affected LAN port and alerts users. Unidirectional links can cause a variety of problems, including spanning tree topology loops. In Cisco IOS XE Release 3.9S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. The following sections provide information about this feature:
Information About the UDLD Protocol, page 2 How to Configure the UDLD Protocol, page 4
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Contents
This guide covers the following topics:
Gigabit Ethernet Management Interface Overview, page 2 Gigabit Ethernet Port Numbering, page 2 Gigabit Ethernet Port Numbering, page 2 IP Address Handling in ROMmon and the Management Ethernet Port, page 2 Gigabit Ethernet Management Interface VRF, page 3 Common Ethernet Management Tasks, page 3
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Using the Management Ethernet Interface Gigabit Ethernet Management Interface Overview
Each RP has a Management Ethernet interface, but only the active RP has an accessible Management Ethernet interface (the standby RP can be accessed using the console port, however). IPv4, IPv6, and ARP are the only routed protocols supported for the interface. The interface provides a method of access to the router even if the SPA interfaces or the IOS processes are down. The Ethernet Management Interface cannot be used as a Lawful Intercept MD source interface. The Management Ethernet interface is part of its own VRF. This is discussed in more detail in the Gigabit Ethernet Management Interface VRF section on page 3.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Using the Management Ethernet Interface Gigabit Ethernet Management Interface VRF
In dual RP configurations, however, users should never configure the IP address in the ROMmon on either RP0 or RP1 to match each other or the IP address as defined by the IOS CLI. Configuring matching IP addresses introduces the possibility for an active and standby Management Ethernet interface having the same IP address with different MAC addresses, which will lead to unpredictable traffic treatment.
Many features must be configured or used inside the VRF, so the CLI may be different for certain Management Ethernet functions on the Cisco ASR 1000 Series Routers than on Management Ethernet interfaces on other routers. Prevents transit traffic from traversing the router. Because all of the SPA interfaces and the Management Ethernet interface are automatically in different VRFs, no transit traffic can enter the Management Ethernet interface and leave a SPA interface, or vice versa. Improved security of the interface. Because the Mgmt-intf VRF has its own routing table as a result of being in its own VRF, routes can only be added to the routing table of the Management Ethernet interface if explicitly entered by a user.
The Management Ethernet interface VRF supports both IPv4 and IPv6 address families.
Viewing the VRF Configuration, page 4 Viewing Detailed VRF Information for the Management Ethernet VRF, page 4 Setting a Default Route in the Management Ethernet Interface VRF, page 4 Setting the Management Ethernet IP Address, page 5 Telnetting over the Management Ethernet Interface, page 5 Pinging over the Management Ethernet Interface, page 5 Copy Using TFTP or FTP, page 5 NTP Server, page 6 SYSLOG Server, page 6 SNMP-Related Services, page 6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Domain Name Assignment, page 6 DNS service, page 6 RADIUS or TACACS+ Server, page 6 VTY lines with ACL, page 7
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
IPv6 Example
Router(config)# interface GigabitEthernet 0 Router(config-if)# ipv6 address X:X:X:X::X
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
FTP Example
Router(config)# ip ftp source-interface gigabitethernet 0
NTP Server
To allow the software clock to be synchronized by a Network Time Protocol (NTP) time server over the Management Ethernet interface, enter the ntp server vrf Mgmt-intf command and specify the IP address of the device providing the update. The following CLI provides an example of this procedure.
Router(config)# ntp server vrf Mgmt-intf 172.17.1.1
SYSLOG Server
To specify the Management Ethernet interface as the source IP or IPv6 address for logging purposes, enter the logging host <ip-address> vrf Mgmt-intf command. The following CLI provides an example of this procedure.
Router(config)# logging host <ip-address> vrf Mgmt-intf
SNMP-Related Services
To specify the Management Ethernet interface as the source of all SNMP trap messages, enter the snmp-server source-interface traps gigabitEthernet 0 command. The following CLI provides an example of this procedure:
Router(config)# snmp-server source-interface traps gigabitEthernet 0
DNS service
To specify the Management Ethernet interface VRF as a name server, enter the ip name-server vrf Mgmt-intf IPv4-or-IPv6-address command.
Router(config)# ip name-server vrf Mgmt-intf IPv4-or-IPv6-address
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
The same concept is true for configuring a TACACS+ server group. To group the Management VRF as part of a TACACS+ server group, enter the ip vrf forwarding Mgmt-intf command when configuring the TACACS+ server group.
RADIUS Server Group Configuration
Router(config)# aaa group server radius hello Router(config-sg-radius)# ip vrf forwarding Mgmt-intf
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Additional References
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Using the Management Ethernet Interface Feature Information for Using the Management Ethernet Interface
Note
Table 3 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 3
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Using the Management Ethernet Interface Feature Information for Using the Management Ethernet Interface
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Contents
This guide covers the following topics:
Prerequisites for Network Synchronization Support, page 2 Network Synchronization Overview, page 2 Synchronization Status Message and Ethernet Synchronization Messaging Channel, page 5 Restrictions for Network Synchronization, page 6 Configuring Network Synchronization, page 7
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Synchronize the greatest number of network elements to the smallest number of independent clock sources. Ideally, all the network elements should be synchronized to a single clock source. Use clock sources of the highest quality (in terms of stability and long-term accuracy). To ensure resiliency of synchronization, plan for possible failure of the clock sources, network elements, and network trunks.
Framing Modes Supported T1 ESF T1 SF T1 D4 E1 CRC4 E1 FAS E1 CAS E1 CAS CRC4 2048 kHz
SSM or QL Support Yes Yes Yes Yes Yes Yes Yes Yes
Table 2 lists the framing modes for a BITS port on the other Cisco ASR 1000 Series Aggregation Services Routers.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 2
Framing Modes for a BITS or SSU Port on the Other Cisco ASR 1000 Series Aggregation Services Routers
Framing Modes Supported T1 ESF T1 SF E1 CRC4 E1 FAS E1 CAS E1 CAS CRC4 2048 kHz
SSM or QL Support No No No No No No No
Tx Port No No No No No No No
You can configure network synchronization on the Cisco ASR 1000 Series Aggregation Services Routers by using one of the following features:
Clock Recovery from SyncE When this feature is configured, the system clock is recovered from the SyncE clocking source (SyncE-enabled interfaces only). The router uses this clock as the Tx clock for other supported Shared Port Adapters (SPAs).
Clock Recovery from an External Interface When this feature is enabled, the system clock is recovered from a BITS clock source. Clock Recovery from a GPS (10M) Source
Note
When this feature is enabled, the system clock is recovered from a GPS (10M) clock source.
Line to External
Note
When this feature is enabled, the clock received from an Ethernet is forwarded to an external SSU. The SyncE feature provides the clock cleanup functionality. When a router is in the middle of a synchronization chain, the received clock may experience unacceptable wander and jitter. The router recovers the clock from the SyncE interface, converts it to the format required for the BITS interface, and sends it to an SSU through the BITS port. The SSU then performs a cleanup and sends it back to the BITS interface. The cleaned up clock is received from the SSU and is used as the Tx clock for the SyncE ports. In the context of the Cisco ASR 1000 Series Aggregation Services Routers, the interface from which the clock is recovered and the BITS port to the SSU must reside on the same card. A SyncE-enabled Cisco ASR 1000 Series Router provides the Squelching feature. In this feature, an alarm indication signal (AIS) is sent to the Tx interfaces if the clock source goes down. When the Line to External feature is configured, if the line source goes down at any point of time, an AIS is transmitted through the external interface to the SSU. Squelching can be performed only on external devices, such as SSUs and PRCs.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
You can have a maximum of eight clock sources configured on a Cisco ASR 1000 Series Router. On a router that supports the Network Synchronization feature, you can configure selection of the clock source on the basis of the quality of the clock source. With this feature configured, the clock source that offers the best quality is made the default clock source. If the highest level of quality is offered by more than one clock source, the clock source with the highest priority is made the default clock source. You can also manage synchronization by using the following management options:
Hold-Off Time: If a clock source goes down, the router waits for a specific hold-off time before removing the clock source from the clock selection process. By default, the value of hold-off time is 300 milliseconds (ms). Wait to Restore: If a SyncE interface comes up, the router waits for a specific period of time before considering the SyncE interface for synchronization source. By default, the value is 300 seconds. Force Switch: Forcefully selects a synchronization source irrespective of whether the source is available or within the specified range. Manual Switch: Manually select a synchronization source, provided the clock source has a higher quality level than the currently active clock.
SPA Name SPA_TYPE_HYBRID_2KP SPA_TYPE_PRO_1xCHOC3_STM1 SPA_TYPE_CHOP_1xCHOC12 SPA_TYPE_CEOP_1xOC3 SPA_TYPE_CEOP_24xT1E1 SPA_TYPE_TATM_1xOC3 SPA_TYPE_TATM_2xOC3 SPA_TYPE_TATM_3xOC3 SPA_TYPE_TATM_1xOC12
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Network Synchronization Support Synchronization Status Message and Ethernet Synchronization Messaging Channel
Table 3
SPA Name SPA_TYPE_POS_2xOC3 SPA_TYPE_POS_4xOC3 SPA_TYPE_POS_1xOC12 SPA_TYPE_POS_2xOC12 SPA_TYPE_POS_MF_4xOC3 SPA_TYPE_POS_MF_8xOC3 SPA_TYPE_POS_MF_2xOC12 SPA_TYPE_POS_MF_4xOC12 SPA_TYPE_POS_MF_8xOC12 SPA_TYPE_POS_SRP_OC192 SPA_TYPE_POS_SRP_OC192_XFP SPA_TYPE_POS_SRP_1xOC48 SPA_TYPE_POS_SRP_2xOC48 SPA_TYPE_POS_SRP_4xOC48
Prevents timing loops.Provides fast recovery when a part of the network fails. Ensures that a node gets timing from the most reliable clock source.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
The ESMC packets are received only for the ports configured as clock sources, and transmitted on all the SyncE interfaces in the system. These packets are then processed by the clock selection algorithm on route processors (RP) and are used to select the best clock. The Tx frame is generated based on the QL value of the selected clock source, and sent to all the enabled SyncE ports.
When multiple selection processes are present in a network element, all the processes work in the same mode.
QL-Enabled Mode
In QL-enabled mode, the following parameters contribute to the selection process:
If no external commands are active, the algorithm selects the reference (for clock selection) with the highest QL that does not experience a signal fail condition. If multiple inputs have the same highest QL, the input with the highest priority is selected. For multiple inputs having the same highest priority and QL, the existing reference is maintained (if it belongs to the highest priority and QL group). Otherwise, an arbitrary reference from the highest priority and QL group is selected.
QL-Disabled Mode
In QL-disabled mode, the following parameters contribute to the selection process:
If no external commands are active, the algorithm selects the reference (for clock selection) with the highest priority that does not experience a signal fail condition. For multiple inputs having the same highest priority, the existing reference is maintained (if it belongs to highest priority group). Otherwise, an arbitrary reference from highest priority group is selected.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
If the network clock algorithm is enabled, use the system clock as the Tx clock (synchronous mode) for the Ethernet interfaces of the corresponding router. You cannot change the synchronous mode on a per-interface basis. You can configure up to eight ports as clock sources on a router. The SyncE feature coexists with SSO, but is not SSO-compliant. The clock selection algorithm is restarted on a switchover. During switchover, the router goes into holdover mode. The SyncE interfaces in the WAN mode cannot be used for QL-enabled clock selection. You must either use them with the system in QL-disabled mode, or disable the ESMC on the interfaces, and use them as QL-disabled interfaces. We recommend that you do not configure multiple input sources with the same priority because this impacts the TSM (switching message delay). You cannot implement the network clock-based clock selection algorithm and the new algorithm simultaneously. Both these are mutually exclusive. The Line to External feature for clock cleanup is supported only if the line interface and the external interface are on the same metronome SPA.
Note
The Line to External feature is not supported on the Cisco ASR 1002-X Router.
Configuring Clock Recovery from SyncE, page 7 Configuring Clock Recovery from a BITS Port, page 9 Configuring SyncE by Using the Line to External Feature, page 13
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
configure terminal network-clock synchronization automatic network-clock synchronization ssm option {1 | 2 {GEN1 | GEN2}} interface gigabitethernet slot/card/port synchronous mode exit network-clock input-source priority {interface interface-name slot/card/port | {external slot/card/port}} exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
Example:
Router(config)# network-clock synchronization automatic
Enables the network clock selection algorithm. This command disables the Cisco-specific network clock process, and turns on the G.781-based automatic clock selection process. Configures the equipment to work in a synchronization network. The option_id value 1 refers to a synchronization network design for Europe. This is the default value. The option_id value 2 refers to a synchronization network design for the U.S. Specifies the Gigabit Ethernet interface to be configured: slot/card/portSpecifies the location of the interface.
Step 3
Example:
Router(config)# network-clock synchronization ssm option 2 GEN1
Step 4
Example:
Router(config)# interface gigabitethernet 0/2/0
Step 5
synchronous mode
Example:
Router(config-if)# synchronous mode
Step 6
exit
Example:
Router(config)# exit
Step 7
network-clock input-source priority {interface interface-name slot/card/port | {external slot/card/port}} Router(config)# network-clock input-source 1 interface gigabitethernet 0/2/0 Router(config)# network-clock input-source 1 external R0 2048k
Enables clock recovery from SyncE. The Cisco ASR1006 router supports two RP ports, one active and the other standby.
Step 8
exit
Example:
Router(config)# exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Examples
The following example shows how to configure clock recovery from SyncE:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN1 Router(config)# interface gigabitethernet 0/2/0 Router(config-if)# synchronous mode Router(config)# exit Router(config)# network-clock input-source 1 interface gigabitethernet 0/2/0 Router(config)# exit
Configuring Clock Recovery with a BITS Port as an Input-Source, page 9 Configuring Clock Recovery with a BITS Port as an Output-Source, page 11
SUMMARY STEPS
1. 2. 3. 4. 5.
configure terminal network-clock synchronization automatic network-clock synchronization ssm option option-id generation-id network-clock input-source priority {external slot/card/port} exit
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password if prompted.
Example:
Router# enable
Step 2
configure terminal
Example:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 3
network-clock synchronization automatic
Purpose Enables the network clock selection algorithm. This command disables the Cisco-specific network clock process, and turns on the G.781-based automatic clock selection process. Configures the equipment to work in the synchronization network. The option_id value 1 refers to synchronization network design for Europe. This is the default value. The option_id value 2 refers to the synchronization network design for the U.S. Enables clock recovery from a BITS port.
Note
Example:
Router(config)# network-clock synchronization automatic
Step 4
Example:
Router(config)# network-clock synchronization ssm option 2 GEN1
Step 5
Example:
Router(config)# network-clock input-source 1 External 0/3/0 t1 esf Router(config)# network-clock input-source 1 External R0 t1 esf
Routers with dual hardware support, such as the Cisco ASR 1006 Router, can have two RP ports, wherein one RP is active and the other is standby. Both the active and standby RP BITS ports can be configured as output sources.
Step 6
exit
Example:
Router(config)# exit
Examples
The following example shows how to configure clock recovery from a BITS port for a Metronome SPA:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN1 Router(config)# network-clock input-source 1 external 0/3/0 t1 esf Router(config)# exit
The following example shows how to configure clock recovery from a BITS port for RP BITS on Cisco ASR 1000 Series Aggregation Services Routers with dual RP:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN Router(config)# network-clock input-source 1 External R0 t1 esf Router(config)# exit
The following example shows how to configure clock recovery with BITS as the input source on the Cisco ASR 1002-X Series Aggregation Services Routers on the E1 Common Channel Signal mode:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN Router(config)# network-clock input-source 1 external r0 e1 cas crc4 120 linecode Router(config)# exit
Note
BITS configuration as output sources is supported only on Cisco ASR 1002-X Router.
SUMMARY STEPS
1. 2. 3. 4. 5.
configure terminal network-clock synchronization automatic network-clock synchronization ssm option option-id generation-id network-clock output-source priority {external slot/card/port} exit
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password if prompted.
Example:
Router# enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# network-clock synchronization automatic
Enables the network clock selection algorithm. This command disables the Cisco-specific network clock process, and turns on the G.781-based automatic clock selection process. Configures the equipment to work in synchronization network. The option_id value 1 refers to synchronization networks design for Europe. This is the default value. The option_id value 2 refers to the synchronization networks design for the U.S.
Step 4
Example:
Router(config)# network-clock synchronization ssm option 2 GEN1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Command
Step 5
network-clock output-source priority {external slot/card/port}
Example:
Router(config)# network-clock output-source system 1 External 0/3/0 t1 esf Router(config)# network-clock output-source 1 External R0 t1 esf
For routers with dual hardware support such as the Cisco ASR 1006 Router can have two RP ports wherein one RP is active and the other is standby. Both the active and standby RP BITS ports can be configured as output sources.
Step 6
exit
Example:
Router(config)# exit
Examples
The following example shows how to configure clock recovery from a BITS port for a Metronome SPA:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN1 Router(config)# network-clock output-source 1 external 0/3/0 t1 esf Router(config)# exit
The following example shows how to configure clock recovery from a BITS port for RP BITS on Cisco ASR 1000 Series Aggregation Services Routers with dual RP:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN Router(config)# network-clock output-source 1 external R0 t1 esf Router(config)# exit
The following example shows how to configure clock recovery with BITS as output-source on Cisco ASR 1002-X Series Aggregation Services Routers on a E1 Common Channel Signal Mode:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN Router(config)# network-clock output-source 1 external r0 e1 cas crc4 120 linecode Router(config)# exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Note
The Line to External feature is not supported on the Cisco ASR 1002-X Router.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8.
configure terminal network-clock synchronization automatic network-clock synchronization ssm option {1 | 2 {GEN1 | GEN2}} interface gigabitethernet slot/card/port synchronous mode exit network-clock output-source line priority {interface interface-name} {external slot/card/port} exit
DETAILED STEPS
Command
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
Example:
Router(config)# network-clock synchronization automatic
Enables the network clock selection algorithm. This command disables the Cisco-specific network clock process, and turns on the G.781-based automatic clock selection process. Configures the equipment to work in a synchronization network. The option_id value 1 refers to a synchronization network design for Europe. This is the default value. The option_id value 2 refers to a synchronization network design for the U.S.
Step 3
Example:
Router(config)# network-clock synchronization ssm option 2 GEN1
Step 4
Specifies the Gigabit Ethernet interface to be configured: slot/card/portSpecifies the location of the interface.
Example:
Router(config)# interface gigabitethernet 0/2/0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Command
Step 5
synchronous mode
Example:
Router(config-if)# synchronous mode
Step 6
exit
Example:
Router(config)# exit
Step 7
Example:
Router(config-if-srv)# network-clock output-source line 1 interface gigabitethernet 0/2/0 external 0/3/0
Step 8
exit
Example:
Router(config)# exit
Examples
The following example shows how to configure a SyncE using the Line to External method:
Router# configure terminal Router(config)# network-clock synchronization automatic Router(config)# network-clock synchronization ssm option 2 GEN1 Router(config)# interface gigabitethernet 0/2/0 Router(config-if)# synchronous mode Router(config)# exit Router(config)# network-clock output-source line 1 interface gigabitethernet 0/2/0 external 0/3/0 Router(config)# exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Managing Synchronization
Manage synchronization on a Cisco ASR 1000 Series Aggregation Service Router using the following management commands:
network-clock synchronization mode QL-enabled command Use the network-clock synchronization mode QL-enabled command in the global configuration mode to configure the automatic selection process for the QL-enabled mode. This succeeds only if the SyncE interfaces are capable of sending SSMs. The following example shows how to configure network clock synchronization (QL-enabled mode) in the global configuration mode:
Router(config)# network-clock synchronization mode QL-enabled
esmc process command Use the esmc process command in the global configuration mode to enable the ESMC process at system level. The no form of this command disables the ESMC process. The no form of this command fails if no SyncE-capable interface is installed on the platform. The following example shows how to enable the ESMC process in the global configuration mode:
Router(config)# esmc process
esmc mode [tx | rx] command Use the esmc mode [tx | rx] command in the interface configuration mode to enable the ESMC process at the interface level. The no form of the command disables the ESMC process. The following example shows how to enable ESMC in the interface configuration mode:
Router(config-if)# esmc mode tx
network-clock quality-level command Use the network-clock source quality-level command in the interface configuration mode to configure the QL value for ESMC on a gigabit Ethernet port. The value is based on global interworking options:
If Option 1 is configured, the available values are QL-PRC, QL-SSU-A, QL-SSU-B, QL-SEC,
and QL-DNU.
If Option 2 is configured with GEN 2, the available values are QL-PRS, QL-STU, QL-ST2,
QL-SMC, QL-ST4, and QL-DUS The following example shows how to configure the network-clock source quality-level in the interface configuration mode:
Router(config-if)# network-clock source quality-level QL-PRC rx
Use the network-clock quality-level command in the global configuration mode to configure the QL value for the SSMs on a BITS port. The following example shows how to configure network-clock quality-level command in the global configuration mode:
Router(config)# network-clock quality-level rx qL-pRC external R0 2048k
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
network-clock wait-to-restore command Use the network-clock wait-to-restore timer global command to set the wait-to-restore time. You can configure the wait-to-restore time to any value between 0 to 86400 seconds. The default value is 300 seconds. The wait-to-restore timer can be set in the global configuration mode and the interface configuration mode. The following example shows how to configure the wait-to-restore timer in the global configuration mode:
Router(config)# network-clock wait-to-restore 10 global
The following example shows how to configure the wait-to-restore timer in the interface configuration mode:
Router(config)# interface gigabitethernet 0/2/0 Router(config-if)# network-clock wait-to-restore 10
network-clock hold-off command Use the network-clock hold-off timer global command to configure hold-off time. You can configure the hold-off time to either 0 or any value between 50 to 10000 ms. The default value is 300 ms. The network-clock hold-off timer can be set in the global configuration mode and the interface configuration mode. The following example shows how to configure the hold-off timer:
Router(config-if)# network-clock hold-off 50 global
network-clock switch force command Use the network-clock switch force command to forcefully select a synchronization source irrespective of whether the source is available, and within range. The following example shows how to configure a force switch:
Router# network-clock switch force interface gigabitethernet 0/2/0
network-clock switch manual command Use the network-clock switch manual command to manually select a synchronization source, provided the clock source has a higher quality level than the currently active clock. The following example shows how to configure a manual switch:
Router# network-clock switch manual interface gigabitethernet 0/2/0
network-clock clear switch controller-id command Use the network-clock clear switch controller-id command to clear the manual, or switch it on by force. The following example shows how to clear a switch:
Router# network-clock clear switch t0
network-clock set lockout command Use the network-clock set lockout command to lockout a clock source. A clock source flagged as lockout is not selected for SyncE. To clear the lock-out on a source, use the network-clock clear lockout command. The following example shows how to lock out a clock source:
Router# network-clock set lockout interface gigabitethernet 0/2/0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
The following example shows how to clear the lock out on a clock source:
Router# network-clock clear lockout interface gigabitethernet 0/2/0
Automatic selection process : Enable Equipment Clock : 1544 (EEC-Option2) Clock Mode : QL-Enable ESMC : Enabled SSM Option : GEN1 T0 : External R0 t1 esf Hold-off (global) : 300 ms Wait-to-restore (global) : 300 sec Tsm Delay : 180 ms Revertive : No Force Switch: FALSE Manual Switch: FALSE Number of synchronization sources: 2 sm(netsync NETCLK_QL_ENABLE), running yes, state 1A Last transition recorded: (src_rem)-> 1A (src_added)-> 1A (src_rem)-> 1A (src_added)-> 1A (ql_change)-> 1A (sf_change)-> 1A (force_sw)-> 1C (clear_sw)-> 1A (sf_change)-> 1A (sf_change)-> 1A
Nominated Interfaces Interface Internal Gi1/2/0 *External R0 SigType NA NA T1 ESF Mode/QL NA/Dis Sync/En NA/En Prio QL_IN ESMC Tx 251 QL-ST3 NA 1 QL-FAILED 2 QL-STU NA ESMC Rx NA NA
Use the show network-clock synchronization detail command to display all the details of network clock synchronization parameters at the global and interface level, as shown in the following example:
Router# show network-clock synchronization detail Symbols: En NA * # & Enable, Dis - Disable, Not Applicable Synchronization source Synchronization source Synchronization source Adis - Admin Disable selected force selected manually switched
Automatic selection process : Enable Equipment Clock : 1544 (EEC-Option2) Clock Mode : QL-Enable ESMC : Enabled SSM Option : GEN1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
T0 : External R0 t1 esf Hold-off (global) : 300 ms Wait-to-restore (global) : 300 sec Tsm Delay : 180 ms Revertive : No Force Switch: FALSE Manual Switch: FALSE Number of synchronization sources: 2 sm(netsync NETCLK_QL_ENABLE), running yes, state 1A Last transition recorded: (src_rem)-> 1A (src_added)-> 1A (src_rem)-> 1A (src_added)-> 1A (ql_change)-> 1A (sf_change)-> 1A (force_sw)-> 1C (clear_sw)-> 1A (sf_change)-> 1A (sf_change)-> 1A
Nominated Interfaces Interface Internal Gi1/2/0 *External R0 SigType NA NA T1 ESF Mode/QL NA/Dis Sync/En NA/En Prio 251 1 2 QL_IN ESMC Tx QL-ST3 NA QL-FAILED QL-STU NA ESMC Rx NA NA
Interface: --------------------------------------------Local Interface: Internal Signal Type: NA Mode: NA(Ql-enabled) SSM Tx: Disable SSM Rx: Disable Priority: 251 QL Receive: QL-ST3 QL Receive Configured: QL Receive Overrided: QL Transmit: QL Transmit Configured: Hold-off: 0 Wait-to-restore: 0 Lock Out: FALSE Signal Fail: FALSE Alarms: FALSE Slot Disabled: FALSE Local Interface: Gi1/2/0 Signal Type: NA Mode: Synchronous(Ql-enabled) ESMC Tx: Disable ESMC Rx: Enable Priority: 1 QL Receive: QL-PRS QL Receive Configured: QL Receive Overrided: QL-FAILED QL Transmit: QL-DUS QL Transmit Configured: Hold-off: 300 Wait-to-restore: 300 Lock Out: FALSE Signal Fail: FALSE Alarms: TRUE Slot Disabled: FALSE Local Interface: External R0 Signal Type: T1 ESF Mode: NA(Ql-enabled) SSM Tx: Disable SSM Rx: Enable
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
Priority: 2 QL Receive: QL-STU QL Receive Configured: QL Receive Overrided: QL Transmit: QL Transmit Configured: Hold-off: 300 Wait-to-restore: 300 Lock Out: FALSE Signal Fail: FALSE Alarms: FALSE Slot Disabled: FALSE
Use the show esmc command to display the ESMC configuration output:
Router# show esmc Interface: GigabitEthernet0/0/0 Administative configurations: Mode: Synchronous ESMC TX: Enable ESMC RX: Enable QL TX: QL RX: Operational status: Port status: UP QL Receive: QL-PRC QL Transmit: QL-DNU QL rx overrided: ESMC Information rate: 1 packet/second ESMC Expiry: 5 second Interface: GigabitEthernet0/0/0 Administrative configurations: Mode: Synchronous ESMC TX: Enable ESMC RX: Enable QL TX: QL RX: Operational status: Port status: UP QL Receive: QL-DNU QL Transmit: QL-DNU QL rx overrided: QL-DNU ESMC Information rate: 1 packet/second ESMC Expiry: 5 second
Use the show esmc detail command to display all the details of the ESMC parameters at the global and interface level, as shown in the following example:
Router# show esmc detail Router#show esmc detail Interface: GigabitEthernet0/0/0 Administative configurations: Mode: Synchronous ESMC TX: Enable ESMC RX: Enable QL TX: QL RX: QL-PRS Operational status: Port status: UP QL Receive: QL-DUS QL Transmit: QL-ST3 QL rx overrided: QL-DUS
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
Information rate: 1 packet/second Expiry: 5 second Tx Timer: Running Rx Timer: Running Tx interval count: 1 INFO pkts in: 0 INFO pkts out: 256 EVENT pkts in: 0 EVENT pkts out: 0
Before you troubleshoot, ensure that all the network synchronization configurations are complete. Table 4 provides information about troubleshooting scenarios that you may encounter while configuring network synchronization.
Table 4 Troubleshooting Scenarios
Solution
Verify that there are no alarms on the interfaces. Use the show network-clock synchronization detail command to check this. Ensure that the nonrevertive configurations are in place.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Table 4
Solution
Verify that there are no alarms on the interfaces. Use the show network-clock synchronization detail RP command to confirm. Use the show network-clock synchronization command to confirm if the system is in revertive mode or nonrevertive mode and verify the nonrevertive configurations as shown in this example:
Router#show network-clock synchronization Symbols: En - Enable, Dis - Disable, Adis - Admin Disable NA - Not Applicable * # & - Synchronization source selected - Synchronization source force selected - Synchronization source manually switched
Automatic selection process : Enable Equipment Clock : 1544 (EEC-Option2) Clock Mode : QL-Enable ESMC : Enabled SSM Option : GEN1 T0 : External R0 t1 esf Hold-off (global) : 300 ms Wait-to-restore (global) : 300 sec Tsm Delay : 180 ms Revertive : No Force Switch: FALSE Manual Switch: FALSE Number of synchronization sources: 2 sm(netsync NETCLK_QL_ENABLE), running yes, state 1A Last transition recorded: (src_rem)-> 1A (src_added)-> 1A (src_rem)-> 1A (src_added)-> 1A (ql_change)-> 1A (sf_change)-> 1A (force_sw)-> 1C (clear_sw)-> 1A (sf_change)-> 1A (sf_change)-> 1A
Incorrect QL values observed when you use the show network-clock synchronization detail command.
Use the network-clock synchronization SSM (option 1 |option 2) command to confirm that there is no framing mismatch. Use the show run interface command to validate the framing for a specific interface. For SSM option 1, framing should be SDH or E1, and for SSM option 2, it should be T1.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
Additional References
Related Documents
Related Topic Cisco IOS commands Document Title Cisco IOS Master Commands List, All Releases
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
Note
Table 5 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 5
Feature Name
Releases
Feature Information In Cisco IOS XE Release 3.2S, this feature was introduced on the Cisco ASR 1000 Series Aggregation Service Routers. In Cisco IOS XE Release 3.7S, the commands that are used to configure this feature have been extended with the introduction of the Cisco ASR 1002-X Router.
Network Cisco IOS Synchronization Support XE 3.2S Network Cisco IOS Synchronization Support XE 3.7S
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
Generic Routing Encapsulation (GRE) is a tunneling protocol that encapsulates a wide variety of network layer protocols inside virtual point-to-point links over a Layer 3 IPv4 or Layer 3 IPv6 access network. Ethernet over GRE (EoGRE) is a new aggregation solution for aggregating WiFi traffic from hotspots. This solution enables customer premises equipment (CPE) devices to bridge the Ethernet traffic coming from an end host, and encapsulate the traffic in Ethernet packets over an IP GRE tunnel. When the IP GRE tunnels are terminated on a service provider broadband network gateway, the end hosts traffic is terminated and subscriber sessions are initiated for the end host.
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Service Provider WiFi: Support for Integrated Ethernet Over GRE Finding Feature Information
Contents
Restrictions for Configuring Ethernet Over GRE, page 3 Prerequisites for Configuring Ethernet Over GRE, page 3 Information About Configuring Ethernet Over GRE, page 3 Supported Features, page 8 How to Configure the EoGRE Feature, page 8 Additional References, page 13 Feature Information for Configuring Ethernet Over GRE, page 14
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Restrictions for Configuring Ethernet Over GRE
IPsec tunnel between the Cisco ASR 1000 Series Aggregation Services Routers and the CPE devices. Native multicast coexistence for subscribers Per-CPE QoS IPv6 subscriber The Cisco Intelligent Services Gateway (ISG) RADIUS proxy initiator QinQ tag for the inner L2 frame High Availability is not supported.
A physical interface or dot1Q interface should be configured. The ISG policy should not be applied to the physical interface.
Terminates IPv4 or IPv6 GRE tunnels. Manages the subscriber session for end-host clients.
The EoGRE feature works with legacy residential gateways and CPE devices to terminate the Ethernet L2 traffic in the Cisco ASR 1000 Series Aggregation Services Routers. When configured as an intelligent Wireless Access Gateway (iWAG) with EoGRE access tunneling support, the Cisco ASR 1000 Series Aggregation Services Routers can extend mobility and the ISG services in support of these legacy devices. Figure 2 shows the structure of the EoGRE feature with PMIP/GTP integrated for mobility service.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Information About Configuring Ethernet Over GRE
Figure 2
Structure of the EoGRE Feature with PMIP/GTP Integrated for Mobility Service
Indoor Hotspot
IP or Ethernet Aggregation Network iWAG with EoGRE Access Public User IP Traffic
Internet
Metro WiFi
3G
9:42 AM
Internet
Indoor/Outdoor Managed AP
User IP obtained via DHCP. AP in DHCP relay mode Proxy ARP for Subscribers EoGRE Tunnel IP Address = RG IP Address
GGSN or PGW
360124
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Information About Configuring Ethernet Over GRE
Figure 3 shows the structure of the EoGRE feature for simple IP service.
Figure 3 Structure of the EoGRE Feature for Simple IP Service
Indoor Hotspot
IP or Ethernet Aggregation Network iWAG with EoGRE Access NAT Public User IP Traffic
IP/MPLS
Internet
Metro WiFi
3G
9:42 AM
IP/MPLS
Internet
Indoor/Outdoor Managed AP
User IP obtained via DHCP. AP in DHCP relay mode Proxy ARP for Subscribers EoGRE Tunnel IP Address = RG IP Address
NAT
360125
(Optional)
EoGRE Deployment with PMIPv6 Integrated for Mobility Service, page 6 EoGRE Deployment with GTP Integrated for Mobility Service, page 7 EoGRE Deployment with ISG Integrated for Simple IP Service, page 7
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Information About Configuring Ethernet Over GRE
Mobile nodes access the mobile internet service over Wi-Fi access points. The access points are either autonomous access points or are connected to the Cisco Wireless LAN Controller (WLC). These access points and WLCs are used as residential gateways or CPE devices. CPEs are preconfigured with a point-to-multipoint GRE IP tunnel to the Cisco ASR 1000 Series Aggregation Services Routers as the MAG. The tunnel from the CPE device can be configured with a static GRE key. The CPEs are provisioned to forward the Ethernet traffic from both public and private customers to the GRE tunnel, and to add a VLAN tag on the Ethernet frame before forwarding the traffic. As with regular PMIPv6 deployments, the Cisco ASR 1000 Series Aggregation Services Routers can create IP sessions on EoGRE access tunnels similar to the regular IP sessions on the physical Ethernet interfaces, and allocate IP addresses for mobile nodes, either locally or in the proxy mode. Mobility service is provided to the mobile nodes and the tunneled Ethernet traffic is forwarded via IP tunnels to the Local Mobility Anchor (LMA).
Note
When you ping a mobile node from the MAG with a packet size that is larger than that of the path maximum transmission unit (PMTU) that is configured with the DF bit set, the packet will be dropped. However, you will not get the return type as M.M.M (could not fragment). This is reflected in the log messages or error messages. For more information about PMIPv6 and the ISG configurations for the iWAG, see the Intelligent Wireless Gateway Configuration Guide, Cisco IOS Release 3S.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Information About Configuring Ethernet Over GRE
3G
9:42 AM
WLC/CPE
Eth
erne
t Ov er IP
iWAG-1
PT unn e
l to
GG
SN
N
3G
9:42 AM
CPE
GT
nel Tun
to G
GS
GGSN
3G
9:42 AM
er Eth
net
Ove
r IP
iWAG-2
360171
CPE
For more information about the GTP and ISG configurations for the iWAG, see the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE Supported Features
Figure 6
Structure of the EoGRE Deployment with ISG Integrated for Simple IP Service
Supported Features
The following features are supported as part of the EoGRE feature on the Cisco ASR 1000 Series Aggregation Services Routers:
Ethernet over GRE traffic termination on the routers Frames can have up to one dot1Q VLAN tag L2-connected IPv4 mobile nodes GRE tunnel for IPv4 or IPv6 ISG and PMIPv6 or GTP integrated with the EoGRE tunnel ISG initiator-unclassified MAC, DHCP, DNAv4 Subscriber roaming
enable configure terminal interface interface-name ip unnumbered loopback interface-name or ip address ip-address tunnel source interface-type interface-number (For simple IP mode) mac-address H.H.H tunnel mode ethernet gre ipv4
5. 6. 7.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE How to Configure the EoGRE Feature
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
interface interface-name
Example:
Router(config)# interface Tunnel 0
Step 4
Example:
Router(config-if)# ip unnumbered loopback 0
For PMIPv6 and GTP scenarios, an unnumbered address or a specified IP address can be configured on the tunnel interface. For a simple IP scenario, only a specified IP address can be configured on the tunnel interface. This IP address can be used as a default gateway IP address.
or
ip address ip-address
Example:
Router(config-if)# ip address 20.1.1.2 255.255.255.0
Step 5
Example:
Router(config-if)# tunnel source Loopback 0
Step 6
Example:
Router(config-if)# mac-address 0000.5e00.5213
Sets the source MAC address for the EoGRE tunnel interface. The MAC address is mandatory for simple IP deployment. For PMIPv6/GTP, the default MAC address associated with EoGRE Tunnel is 0000.5e00.5213.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Service Provider WiFi: Support for Integrated Ethernet Over GRE How to Configure the EoGRE Feature
Command or Action
Step 7
tunnel mode ethernet gre ipv4
Purpose Sets the EoGRE encapsulation mode for the tunnel interface for IPv4. or Sets the EoGRE encapsulation mode for the tunnel interface for IPv6.
Example:
Router(config-if)# tunnel mode ethernet gre ipv4 or tunnel mode ethernet gre ipv6
Example:
Router(config-if)# tunnel mode ethernet gre ipv6
Step 8
Example:
Router(config-if)# tunnel vlan 1000
Step 9
end
Example:
Router(config-if)# end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Service Provider WiFi: Support for Integrated Ethernet Over GRE How to Configure the EoGRE Feature
Examples
aaa new-model ! aaa group server radius AAA_SERVER_CAR server-private 5.3.1.76 auth-port 2145 acct-port 2146 key cisco ! aaa authentication login default none aaa authentication login ISG_PROXY_LIST group AAA_SERVER_CAR aaa authorization network ISG_PROXY_LIST group AAA_SERVER_CAR aaa authorization subscriber-service default local group AAA_SERVER_CAR aaa accounting network PROXY_TO_CAR action-type start-stop group AAA_SERVER_CAR ! aaa accounting network ISG_PROXY_LIST start-stop group AAA_SERVER_CAR ! aaa server radius dynamic-author client 5.3.1.76 server-key cisco auth-type any ignore server-key ! ! ip dhcp excluded-address 172.16.254.254 ! ip dhcp pool ISG_SIMPLE_IP network 172.16.0.0 255.255.0.0 default-router 172.16.254.254 domain-name cisco.com ! policy-map type control EOGRE_L2_ISG class type control always event session-start 2 authorize aaa list ISG_PROXY_LIST password cisco identifier mac-address 4 set-timer IP_UNAUTH_TIMER 5 ! class type control always event service-start 1 service-policy type service identifier service-name 2 collect identifier nas-port ! ! interface Loopback0 ip address 9.9.9.9 255.255.255.255 interface GigabitEthernet1/0/0 ip address 192.168.0.9 255.255.255.0 negotiation auto ! interface GigabitEthernet1/0/0.778 description "to ASR5K GGSN" encapsulation dot1Q 778 ip address 172.16.199.9 255.255.255.0 ! interface Tunnel10 description "EoGRE Tunnel for Simple IP subscribers" mac-address 0000.5e00.5213 ip address 172.16.254.254 255.255.0.0 no ip redirects tunnel source 172.16.199.9 tunnel mode ethernet gre ipv4 service-policy type control EOGRE_L2_ISG ip subscriber l2-connected
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Service Provider WiFi: Support for Integrated Ethernet Over GRE How to Configure the EoGRE Feature
initiator unclassified mac-address initiator dhcp interface Tunnel100 description "IPv4 EoGRE Tunnel for PMIP/GTP subscribers" ip unnumbered Loopback0 tunnel source GigabitEthernet1/0/0 tunnel mode ethernet gre ipv4 tunnel vlan 100 service-policy type control EOGRE_L2_ISG ip subscriber l2-connected initiator unclassified mac-address initiator dhcp ! interface Tunnel200 description "IPv6 EoGRE Tunnel for PMIP/GTP subscribers" ip unnumbered Loopback0 tunnel source 2001:161::9 tunnel mode ethernet gre ipv6 tunnel vlan 200 service-policy type control EOGRE_L2_ISG ip subscriber l2-connected initiator unclassified mac-address initiator dhcp ! mcsa enable sessionmgr ! ipv6 mobile pmipv6-domain D1 replay-protection timestamp window 255 lma LMA_5K ipv4-address 192.168.199.1 ! ipv6 mobile pmipv6-mag M1 domain D1 sessionmgr role 3GPP address ipv4 9.9.9.9 interface Tunnel100 interface Tunnel200 lma LMA_5K D1 ipv4-address 192.168.199.1 encap gre-ipv4 ! ntp master ! gtp information-element rat-type wlan interface local GigabitEthernet1/0/0.778 apn 1 apn-name gtp.com ip address ggsn 172.16.199.1 fixed link-layer address 00ab.00cd.00ef default-gw 20.100.254.254 prefix-len 16 dns-server 20.100.254.254 dhcp-server 20.100.254.254 ! end
You can use the following commands to check and show subscriber session information: show ip dhcp sip statistics show subscriber statistics show subscriber session
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Service Provider WiFi: Support for Integrated Ethernet Over GRE Additional References
show ipv6 mobile pmipv6 mag binding show gtp pdp-context all show interface tunnel-name
Additional References
The following sections provide references related to the Configuring Ethernet over GRE feature.
Related Documents
Related Topic Cisco IOS commands Cisco IOS Configuration Fundamentals Document Title Cisco IOS Master Commands List, All Releases Cisco IOS Configuration Fundamentals Command Reference
Standards
Standard No new or modified standards are supported by this feature. Title
MIBs
No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.
RFCs
No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Service Provider WiFi: Support for Integrated Ethernet Over GRE Feature Information for Configuring Ethernet Over GRE
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Feature Name
Releases
Feature Information This feature enables the Ethernet over Generic Routing Encapsulation (EoGRE) tunnel to be used as a service provider WiFi access interface from CPE devices. A Cisco ASR 1000 Series Aggregation Services Router is used as an L2 aggregator to terminate L2 traffic at the GRE tunnel interface and provide L3 services. In Cisco IOS XE Release 3.9.1S, this feature is implemented on the Cisco ASR 1000 Series Aggregation Services Routers. The following sections provide information about this feature:
Information About Configuring Ethernet Over GRE How to Configure the EoGRE Feature
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Service Provider WiFi: Support for Integrated Ethernet Over GRE Feature Information for Configuring Ethernet Over GRE
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 2012-2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Service Provider WiFi: Support for Integrated Ethernet Over GRE Feature Information for Configuring Ethernet Over GRE
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Contents
Restrictions for Bridge Domain Interfaces, page 1 Information About Bridge Domain Interfaces, page 2 Creating or Deleting a Bridge Domain Interface, page 6 Bridge Domain Interface Scalability, page 6 How to Configure a Bridge Domain Interface, page 6 Additional References, page 10 Feature Information for Configuring Bridge Domain Interfaces, page 11
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
For a BDI, the maximum transmission unit (MTU) size can be configured between 1500 and 9216 bytes.
IP termination Layer 3 VPN termination Address Resolution Protocol (ARP), G-ARP, and P-ARP handling MAC address assignment Ethernet Virtual Circuit Overview, page 2 Bridge Domain Interface Encapsulation, page 3 Assigning a MAC Address, page 3 Support for IP Protocols, page 3 Support for IP Forwarding, page 4 Packet Forwarding, page 4 Bridge Domain Interface Statistics, page 5
Prior to configuring a bridge domain interface, you must understand the following concepts:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Single 802.1Q VLAN tag, priority-tagged, or 802.1ad VLAN tag Both QinQ (inner and outer) VLAN tags, or both 802.1ad S-VLAN and C-VLAN tags Outer 802.1p CoS bits, inner 802.1p CoS bits, or both Payload Ethernet type (five choices are supported: IPv4, IPv6, PPPoE-all, PPoE-discovery, and PPPoE-session) UntaggedMapping to all the frames lacking a 802.1Q or 802.1ad header DefaultMapping to all the frames
For more information on the EVC architecture, see Configuring Ethernet Virtual Connections on the Cisco ASR 1000 Router chapter in the Carrier Ethernet Configuration Guide located at: http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/xe-3s/ce-ether-vc-infra-xe.html
Note
You can configure a static MAC address on a bridge domain interface using the mac-address command.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
IPv4 input and output access control lists (ACL) IPv4 input and output QoS policies. The operations supported for the input and output service policies on a bridge domain interface are:
Classification Marking Policing
IPv4 L3 VRFs
Packet Forwarding
A bridge domain interface provides bridging and forwarding services between the Layer 2 and Layer 3 network infrastructure.
Layer 2 to Layer 3
During a packet flow from a Layer 2 network to a Layer 3 network, if the destination MAC address of the incoming packet matches the bridge domain interface MAC address, or if the destination MAC address is a multicast address, the packet or a copy of the packet is forwarded to the bridge domain interface.
Note
MAC address learning cannot not be performed on the bridge domain interface.
Note
In a bridge domain, when flooding unknown unicast frames, bridge domain interface is not included.
Layer 3 to Layer 2
When a packet arrives at a Layer 3 physical interface of a router, a route lookup action is performed. If route lookup points to a bridge domain interface, then the bridge domain interface adds the layer 2 encapsulation and forwards the frame to the corresponding bridge domain. The byte counters are updated.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
During a Layer 2 lookup on a bridge domain to which the bridge domain interface belongs, the bridge domain forwards the packets to the correct service instance based on the destination MAC address.
Note
Because a bridge domain interface is an internal interface, the operational state of bridge domain interface does not affect the bridge domain operational state.
Admin-down Admin-down
Up Operationally-down
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
When packets flow from a Layer 2 bridge domain network to a Layer 3 routing network through the bridge domain interface, the packets are treated as bridge domain interface input packets and bytes. When packets arrive at a Layer 3 interface and are forwarded through the bridge domain interface to a Layer 2 bridge domain, the packets are treated as output packets and bytes, and the counters are updated accordingly. A BDI maintains a standard set of Layer 3 packet counters as the case with all Cisco IOS interfaces. Use the show interface command to view the Layer 3 packet counters. The convention of the counters is relative to the Layer 3 cloud, for example, input refers to the traffic entering the Layer 3 cloud from the Layer 2 BD, while output refers to the traffic leaving the Layer 3 cloud to the Layer 2 BD. Use the show interfaces accounting command to display the statistics for the BDI status. Use the show interface <if-name> command to display the overall count of the packets and bytes that are transmitted and received.
Note
When a bridge domain interface is created, a bridge domain is automatically created. When both bridge domain interface and bridge domain are created, the system maintains the required associations for mapping the bridge domain-bridge domain interface pair. The mapping of bridge domain and bridge domain interface is maintained in the system. The bridge domain interface uses the index of the associated bridge domain to show the association.
ASR1000-ESP5, ASR1000-ESP10, ASR 1001, ASR1000-ESP10-N, ASR 1002-F (ESP2.5) ASR1000-ESP20 ASR1000-ESP40 4096 4096 4096
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7.
configure terminal interface BDI interface number encapsulation encapsulation dot1q <first-tag> [second-dot1q <second-tag>] ip address ip-address mask mac-address {mac-address} no shut shut
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command or Action
Step 1
configure terminal
Example:
Router# configure terminal
Step 2
Specifies a bridge domain interface on a Cisco ASR 1000 Series Aggregation Services Router.
Example:
Router(config)# interface BDI3
Step 3
Defines the encapsulation type. The example shows how to define dot1q as the encapsulation type. Specifies either the IPv4 or IPv6 address for the bridge domain interface.
Example:
Router(config-if)#encapsulation dot1Q 1 second-dot1q 2
Step 4
or
ipv6 address {X:X:X:X::X link-local | X:X:X:X::X/prefix [anycast | eui-64] | autoconfig [default]}
Example:
Router(config-if)# ip address 2.2.2.1 255.255.255.0
Step 5
Specifies the MAC address for the bridge domain interface. Enables the bridge domain interface on the Cisco ASR 1000 Series Aggregation Services Router.
Step 6
no shut
Example:
hostname(config-if)# no shut
Step 7
shut
Disables the bridge domain interface on the Cisco ASR 1000 Series Aggregation Services Router.
Example:
hostname(config-if)# shut
Example
The following example shows the configuration of a bridge domain interface at IP address 2.2.2.1 255.255.255.0:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# interface BDI3 Router(config-if)# encapsulation dot1Q 1 second-dot1q 2 Router(config-if)# ip address 2.2.2.1 255.255.255.0 Router(config-if)# mac-address 1.1.3 Router(config-if)# no shut
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
You can use different show commands to display the bridge domain interface configuration information:
show interfaces bdiDisplays the configuration summary of the corresponding BDI. Example:
Router# show interfaces BDI3
show platform software interface fp active nameDisplays the bridge domain interface configuration in a Forwarding Processor. Example:
Router# show platform software interface fp active name BDI4
show platform hardware qfp active interface if-name Displays the bridge domain interface configuration in a data path. Example:
Router# show platform hardware qfp active interface if-name BDI4
You can use the following debug commands to debug the bridge domain interface configurations:
debug platform hardware qfp featureDebugs the features in the Cisco Quantum Flow Processor (QFP). The following example shows how to debug the l2bd for all the clients:
Router# debug platform hardware qfp active feature l2bd client all
platform trace runtime process forwarding-manager moduleEnables the Forwarding Manager Route Processor and Embedded Service Processor trace messages for the Forwarding Manager process. In the following example, the trace level for the forwarding processor module in the Forwarding Manager of the ESP processor in slot 0 is set to the informational tracing level (info):
Router(config)# platform trace runtime slot F0 bay 0 process forwarding-manager module interfaces level info
platform trace boottime process forwarding-manager module interfacesEnables the Forwarding Manager Route Processor and Embedded Service Processor trace messages for the Route Processor Forwarding Manager process during bootup. In the following example, the trace level for the forwarding processor module in the Forwarding Manager of the ESP processor in slot R0 is set to the informational tracing level (max):
Router(config)# platform trace boottime slot R0 bay 1 process forwarding-manager forwarding-manager level max
For additional information on the commands and the options available with each command, see the Cisco IOS Configuration Fundamentals Command Reference Guide located at: http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_book.html
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Additional References
Related Documents
Related Topic Document Title Configuring Ethernet Virtual Connections on the Cisco Carrier Ethernet Configuration Guide, Cisco IOS XE Release 3S ASR 1000 Series Aggregation Services Routers EVC Quality of Service Cisco IOS commands http://www.cisco.com/en/US/docs/ios/ios_xe/qos/configuration/gui de/qos_evc_xe.html Cisco IOS Master Commands List, All Releases
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Configuring Bridge Domain Interfaces Feature Information for Configuring Bridge Domain Interfaces
Note
Table 3 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 3
Feature Name Configuring Bridge Domain Interface Configuring Bridge Domain Interface
Feature Information This feature was introduced on the Cisco ASR 1000 Series Aggregation Services Routers. This feature was updated on the Cisco ASR 1000 Series Aggregation Services Routers. The following section was updated for this feature: Information About Bridge Domain Interfaces, page 2
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Configuring Bridge Domain Interfaces Feature Information for Configuring Bridge Domain Interfaces
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
The dense wavelength-division multiplexing (DWDM) wavelengths of the DWDM-XFP-C module on the Cisco ASR 1000 Series Aggregation Services Routers is tunable. You can configure the DWDM ITU wavelengths using the itu channel command in the interface configuration mode. The itu channel command ensures that the traffic continues to flow. Table 4 contains the wavelength mapping information for the DWDM-XFP-C. module
Table 4 DWDM-XFP-C Wavelength Mapping
Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Frequency (THz) 191.95 192.00 192.05 192.10 192.15 192.20 192.25 192.30 192.35 192.40 192.45 192.50 192.55 192.60 192.65 192.70 192.75
Wavelength (nm) 1561.83 1561.42 1561.01 1560.61 1560.20 1559.79 1559.39 1558.98 1558.58 1558.17 1557.77 1557.36 1556.96 1556.55 1556.15 1555.75 1555.34
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Table 4
Channel 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53
Frequency (THz) 192.80 192.85 192.90 192.95 193.00 193.05 193.10 193.15 193.20 193.25 193.30 193.35 193.40 193.45 193.50 193.55 193.60 193.65 193.70 193.75 193.80 193.85 193.90 193.95 194.00 194.05 194.10 194.15 194.20 194.25 194.30 194.35 194.40 194.45 194.50 194.55
Wavelength (nm) 1554.94 1554.54 1554.13 1553.73 1553.33 1552.93 1552.52 1552.12 1551.72 1551.32 1550.92 1550.52 1550.12 1549.72 1549.32 1548.91 1548.51 1548.11 1547.72 1547.32 1546.92 1546.52 1546.12 1545.72 1545.32 1544.92 1544.53 1544.13 1543.73 1543.33 1542.94 1542.54 1542.14 1541.75 1541.35 1540.95
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Table 4
Channel 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82
Frequency (THz) 194.60 194.65 194.70 194.75 194.80 194.85 194.90 194.95 195.00 195.05 195.10 195.15 195.20 195.25 195.30 195.35 195.40 195.45 195.50 195.55 195.60 195.65 195.70 195.75 195.80 195.85 195.90 195.95 196.00
Wavelength (nm) 1540.56 1540.16 1539.77 1539.37 1538.98 1538.58 1538.19 1537.79 1537.40 1537.00 1536.61 1536.22 1535.82 1535.43 1535.04 1534.64 1534.25 1533.86 1533.47 1533.07 1532.68 1532.29 1531.90 1531.51 1531.12 1530.72 1530.33 1529.94 1529.55
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
SUMMARY STEPS
1. 2. 3. 4.
DETAILED STEPS
Command or Action
Step 1
enable source-interface gigabitethernet slot/port
Purpose Enables the privileged EXEC mode. If prompted, enter your password.
Example:
Router# enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Specifies the 10-Gigabit Ethernet interface to be configured. Here: slot/portSpecifies the location of the interface.
Step 4
Sets the ITU channel. numberSpecifies the ITU channel number. The acceptable values are from 182.
Example:
Router(config-if)# itu channel 28
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Vendor Revision = 00 Serial Number (SN) = JFX1617800W Vendor Name = CISCO-JDSU Vendor OUI (IEEE company ID) = 00.01.9C (412) CLEI code = IP9IAGGCAB Cisco part number = 10-2544-02 Device State = Disabled. XFP IDPROM Page 0x0: 000: 0C 00 49 00 F8 00 46 00 FB 00 010: 00 00 00 00 00 00 00 00 A6 04 020: 09 C4 8C A0 13 88 9B 83 13 93 030: 62 1F 1F 07 0F 8D 00 0A 09 CF 040: 00 10 00 18 FF E8 00 0C FF F4 050: 00 00 00 00 00 00 00 00 00 00 060: 00 BF 25 1C 00 C4 00 00 01 F4 070: 00 00 00 00 00 00 00 00 00 00 080: 00 00 00 00 9E 20 00 00 00 00 090: 00 00 00 00 00 00 1E 7C 00 00 100: 00 00 00 01 00 00 00 00 00 00 110: E2 98 00 14 00 00 00 00 00 00 <<See byte 113, the hexa decimal equivalent for ITU channel 20>> 120: 00 00 00 00 00 00 00 01 XFP IDPROM Page 0x1: 128: 0C 98 07 00 00 00 00 00 00 00 138: 08 B4 63 71 50 00 00 00 00 9F 148: 43 49 53 43 4F 2D 4A 44 53
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Contents
It includes the following sections:
Feature Overview, page 2 Configuring Multilink Frame Relay, page 2 Monitoring and Maintaining Frame Relay and Multilink Frame Relay, page 2
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Feature Overview
The Multilink Frame Relay feature is based on the Frame Relay Forums Multilink Frame Relay UNI Implementation Agreement (FRF.16). This feature provides a cost-effective way to increase bandwidth for certain applications by enabling multiple serial links to be aggregated into a single bundle of bandwidth. Multilink Frame Relay is supported on User-to-Network Interface (UNI) networks.
show platform software frame-relayDisplays the statistics about frame relay permanent virtual circuits (PVCs). show platform software mfrDisplays statistics about multilink frame relay information. debug platform hardware qfp active interface frame-relay multilinkDebugs the multilink frame relay interfaces in the Cisco QuantumFlow Processor (QFP). platform trace runtime process forwarding-manager moduleEnables Forwarding Manager Route Processor and Embedded Service Processor trace messages for the forwarding manager process.
You can use the following debug commands to debug the multilink frame relay configurations:
For additional information on the commands and the options available for each command, see the Cisco IOS Configuration Fundamentals Command Reference document, located at: http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_book.html.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Additional References
Related Documents
Related Topic Multilink - Frame Relay (MLFR-FRF.16) Frame Relay Cisco IOS commands Document Title http://www.cisco.com/en/US/docs/ios/ios_xe/wan/configuration/gui de/wan_ml_fr_frf161_xe.html Wide-Area Networking Configuration Guide: Frame Relay, Cisco IOS XE Release 3S Cisco IOS Master Commands List, All Releases
Standards
Standard None Title
MIBs
MIB None MIBs Link To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at this URL: http://www.cisco.com/go/mibs
RFCs
RFC None Title
Technical Assistance
Description Link The Cisco Support and Documentation website http://www.cisco.com/cisco/web/support/index.html provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Monitoring and Maintaining Multilink Frame Relay Feature Information for Monitoring and Maintaining Multilink Frame Relay
Note
Table 5 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 5
Feature Information In Cisco IOS XE Release 3.4S, this feature was introduced on the Cisco ASR 1000 Series Router.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide Copyright 2008 - 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
The Frame Relay to Asynchronous Transfer Mode (ATM) Bridged Interworking feature provides interoperability between the Frame Relay attachment virtual circuit (VC) and the ATM attachment VC that are connected to different provider edge (PE) routers. The bridged encapsulation corresponding to the bridged (Ethernet) interworking mechanism is used to enable this interoperability. The Ethernet frames are carried through the MPLS network using Ethernet over MPLS (EoMPLS). The interworking function is performed in the PE routers connected to the Frame Relay attachment VC and the ATM attachment VC based on RFC 2684 and RFC 2427. The xconnect support on Gigabit EtherChannel (GEC) Virtual Private Wire Service (VPWS) on ASR 1000 feature enables service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructurea Cisco MPLS network. Instead of separate networks with separate network management environments, service providers can deliver Layer 2 connections over an MPLS backbone.
Contents
Overview of L2VPN Interworking, page 2 Virtual Private LAN Services, page 4 Prerequisites for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 12
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 12 Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 14 Gigabit EtherChannel for Virtual Private Wire Service, page 25 Configuring Gigabit EtherChannel for Virtual Private Wire Service, page 27 Additional References, page 38 Feature Information for Configuring MPLS Layer 2 VPNs, page 39 Glossary, page 42
The ethernet keyword causes Ethernet frames to be extracted from an AC and sent over the pseudowire. Ethernet end-to-end transmission is resumed. The AC frames that are not Ethernet are dropped. In the case of VLAN, the VLAN tag is removed, leaving an untagged Ethernet frame. The ip keyword causes IP packets to be extracted from an AC and sent over the pseudowire. The AC frames that do not contain IPv4 packets are dropped.
The following sections explain the Ethernet and IP interworking modes in detail.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
LAN servicesAn example of this is an enterprise that has several sites, with some sites having Ethernet connectivity to the service provider (SP) network and others having Asynchronous Transfer Mode (ATM) connectivity. If the enterprise requires LAN connectivity to all its sites, traffic from the Ethernet or VLAN of one site can be sent through the IP/MPLS network and encapsulated as bridged traffic over an ATM VC of another site. Connectivity servicesAn example of this is an enterprise that has different sites running an Internal Gateway Protocol (IGP) that has incompatible procedures on broadcast and non broadcast links. This enterprise has several sites that run an IGP, such as Open Shortest Path First (OSPF) or Intermediate System-to-Intermediate System (IS-IS), between the sites. In this scenario, some of the procedures (such as route advertisement or designated router election) depend on the underlying L2 protocol and are different for a point-to-point ATM connection versus a broadcast Ethernet connection. Therefore, the bridged encapsulation over ATM can be used to achieve homogenous Ethernet connectivity between the CE routers running an IGP.
IP or Routed Interworking
IP interworking is also called routed interworking. The CE routers encapsulate the IP on the link between the CE router and the PE router. A new VC type is used to signal the IP pseudowire in MPLS. Translation between the L2 and IP encapsulations across the pseudowire is required. Special consideration needs to be given to the address resolution protocol operation and routing protocol operation, because these are handled differently on different L2 encapsulations. The IP interworking mode is used to provide IP connectivity between sites, regardless of the L2 connectivity to these sites. It is different from a Layer 3 VPN because it is point-to-point in nature and the service provider does not maintain any routing information pertaining to customers. Address resolution is encapsulation dependent as specified here:
Ethernet uses Address Resolution Protocol (ARP) ATM uses inverse ARP PPP uses IP Control Protocol (IPCP)
Therefore, address resolution must be terminated on the PE router. Also, the end-to-end address resolution is not supported. Routing protocols operate differently over broadcast and point-to-point media. For Ethernet, the CE routers must either use static routing or configure the routing protocols to treat the Ethernet side as a point-to-point network. In routed interworking, the IP packets that are extracted from the ACs are sent over the pseudowire. The pseudowire works in the IP Layer 2 transport (VC type 0x000B) like-to-like mode. The interworking function at the network service provider's (NSP) end completes the required adaptation based on the AC technology. The non-IPv4 packets are dropped. In routed interworking, the following considerations must be kept in mind:
ARP, inverse ARP, and IPCP are punted to the routing protocol. Therefore, the PE router at the NSP end must provide the following address-resolution functionalities for the Ethernet and ATM and Frame Relay point-to-point subinterface attachment circuits:
EthernetThe PE device acts as a Proxy ARP server to all the ARP requests from the CE router.
The PE router responds with the MAC address of its local interface.
ATM and Frame Relay point-to-point subinterfaceBy default, inverse ARP does not run in the
point-to-point Frame Relay or ATM subinterfaces. The IP address and subnet mask define the connected prefix; therefore, configuration is not required in the CE devices.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Interworking requires that the MTUs in both the ACs must match for the pseudowire that is to come up. The default MTU in one AC must match the MTU of other AC.
Table 1 lists the range of MTUs that can be configured for different ACs.
Table 1 Range of MTUs for Different ACs
1. The MTU configured on an AC must not exceed the MTU in the core network. This ensures that the traffic is not fragmented.
The CE routers with Ethernet attachment VCs running OSPF must be configured with the ospfIfType option so that the OSPF protocol treats the underlying physical broadcast link as a P2P link.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
In order for this to work, the pair of nPEs are programmed to send out BPDUs on the access ring ports in such a way that they appear to be either:
The root bridge itself (the bridge with the lowest bridge ID or priority). The bridge with the second lowest bridge ID or priority, and with a 0 cost path to the root.
Using R-L2GP, you can statically configure the BPDUs instead of the STP generate the BPDUs dynamically. Figure 1 shows the topology of multiple-access networks connected to redundant nPEs.
Figure 1 Multiple-Access Networks Connected to Redundant nPEs
Note
Only localy generated static BPDUs can be sent out to RL2GP ports.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
R-L2GP is supported only on L2 bridge ports, and is not compatible with prestandard MST. All the access-side shall have the same MST instance, the same name and the same revision number configuration as nPEs. There is no configure error detection and recover mechanism for R-L2GP. Users are expected to configure R-L2GP and MSTP instance on CEs and nPEs correctly.
Configuring the MST, page 7 Configuring an R-L2GP Instance, page 8 Attaching an R-L2GP Instance to a Port, page 9 Example: Configuring an R-L2GP, page 10
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring the Layer 2 Protocol Forwarding Virtual Private LAN Services Pseudowire between Two Redundant NPES, page 10
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7.
enable configure terminal spanning-tree mode mst spanning-tree mst configuration [no] name name [no] revision version [no] instance instance-id {vlans vlan-range}
DETAILED STEPS
Command
Step 1
enable
Example:
Router# enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router(config)# spanning-tree mode mst.
Step 4
Example:
Router(config)# spanning-tree mst configuration
Step 5
name name
Example:
Router(config-mst)# name Cisco
All the nodes in the same region should be configured with the same MST name.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 6
revision version
Purpose Sets the revision number for the MST (802.1s) configuration.
Note
Example:
Router(config-mst)# revision 5
All the nodes in the same region should be configured with the same MST configure revision number.
Step 7
Example:
Router(config-mst)# instance 2 vlans 1-100
SUMMARY STEPS
1. 2. 3. 4. 5. 6.
enable configure terminal spanning-tree pseudo-information transmit indentifier remote-id id mst root mst cost
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Configures the Reverse-L2GP configuration on the interface or the untagged Ethernet Flow Point (EFP) port.
Example:
Router(config)# spanning-tree pseudo-information transmit 46
Step 4
remote-id id
Configures the remote R-L2GP instance ID that pairs with the specified R-L2GP instance ID.
Example:
Router(config-pseudo)# remote-id 53
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 5
mst region-id root mac-address
Purpose Adds MST instances to R-L2GP instances and configures the MAC address and priority for MST instances.
Note
Example:
Router(config-pseudo)# mst 0 root 32768 0000.0000.0001
MST 0 has all the VLANs that have not been explicitly specified in other MST instances. MST 0 must be configured for each R-L2GP instance.
Step 6
Example:
Router(config-pseudo)# mst 1 cost 1
Adds the corresponding MST instance list to the R-L2GP instance and configures the R-L2GP path cost for the MST instance or multiple MST instances.
Note
To configure an R-L2GP on the Cisco ASR 1000 Series Aggregation Services Router, the remote-id configured on nPE1 must be the transmit identifier configured on nPE2, and vice versa, as show in Example: Configuring an R-L2GP.
enable configure terminal interface gigabitethernet slot/port or interface tengigabitethernet slot/port spanning-tree pseudo-information transmit indentifier
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 3
interface gigabitethernet slot/port or interface tengigabitethernet slot/port
Purpose Specifies Gigabit Ethernet or the 10 Gigabit Ethernet interface on the access side of the nPE to configure. Here: slot/portSpecifies the location of the interface.
Example:
Router(config)# interface gigabitethernet 4/1
Step 4
Example:
Router(config-if)# spanning-tree pseudo-information transmit 46
The identifier should be the same as the one configured on the nPE.
Configuring the Layer 2 Protocol Forwarding Virtual Private LAN Services Pseudowire between Two Redundant NPES
SUMMARY STEPS
1. 2. 3. 4. 5.
enable configure terminal l2 vfi vfi-name manual vpn id vpn_id bridge-domain bridge_id
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
6. 7.
forward permit l2protocol all neighbor ip-address vc-id {encapsulation mpls |pw-class pw-class-name}
DETAILED STEPS
Command
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Creates a Layer 2 Virtual Forwarding Instance (VFI) and enters the Layer 2 VFI manual configuration submode.
Example:
Router(config)# l2 vfi vfitest1 manual
Step 4
vpn id vpn_id
Example:
Router(config-vfi)# vpn id 303
Step 5
bridge-domain bridge_id
Example:
Router(config-vfi)# bridge-domain 100
Step 6
Example:
Router(config-vfi)# forward permit l2protocol all
Defines the VPLS pseudowire that is used to transport bridge protocol data unit (BPDU) information between two network provider edge (N-PE) routers. Specifies the routers that should form a point-to-point Layer 2 virtual forwarding interface (VFI) connection.
Step 7
Example:
Router(config-vfi)# neighbor 10.10.10.10 1 encapsulation mpls
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Configuring MPLS Layer 2 VPNs Prerequisites for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
msti 2: root_id 32770.0000.0000.0003, root_cost 0, update_flag 0x0 Router# show spanning-tree pseudo-information 1 interface GigabitEthernet3/0/3 Pseudo id 1: GigabitEthernet 2/1/0 GigabitEthernet 0/0/1
Enable frame-relay switching on the Frame Relay provider edge (PE) router. Customer edge (CE) routers must support Bridge-group Virtual Interface or Routed Bridge Encapsulation.
VPI/VCI
FR CE
331935
On the ATM PE router with interworking function, when traffic flows from the ATM segment to MPLS cloud, the bridged encapsulation (ATM and SNAP header) is discarded and the Ethernet frame is encapsulated with the labels required to go through the pseudowire using the VC type 5 (Ethernet). In the opposite direction, after the label disposition from the MPLS cloud, the Ethernet frames are encapsulated over AAL5SNAP using bridged encapsulation.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Configuring MPLS Layer 2 VPNs Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
On the FR PE router with interworking function, when traffic flows from the FR segment to the MPLS cloud, the bridged encapsulation (Frame Relay and SNAP header) is discarded and the Ethernet frame is encapsulated with the labels required to go through the pseudowire, using the VC type 5 (Ethernet). In the opposite direction, after the label disposition from the MPLS cloud, the Ethernet frames are encapsulated over FR using bridged encapsulation. The PE router automatically supports translation of both Cisco and IETF Frame Relay encapsulation types coming from the Customer edge (CE) router, but translates only to IETF when sending to the CE router. The Cisco CE router can handle the IETF encapsulation on receipt, even if it is configured to send Cisco encapsulation. The following modes are supported:
The ATM permanent virtual circuit (PVC) mode with the AAL5SNAP encapsulation type, and the existing Quality of Service (QoS) functionality for ATM PVCs. The Frame Relay DLCI mode, and the existing QoS functionality for Frame Relay.
PVC status signaling works the same way it does in the like-to-like case. The PE router reports the PVC status to the CE router, based on the availability of the pseudowire. The attachment circuit maximum transmission unit (MTU) on both sides of the pseudowire must match when connected over MPLS. The non-AAL5 traffic (such as OAM cells) is punted to be processed at the RP level. A VC that is configured with OAM cell emulation on the ATM PE router (using the oam-ac emulation-enable command) can send end-to-end F5 loopback cells at configured intervals toward the CE router. When the pseudowire is down, an end-to-end F5 segment alarm indication signal (AIS) and remote defect indication (RDI) is sent from the PE router to the CE router. Figure 4 shows the protocol stack for the Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking feature.
Figure 4 Protocol Stack for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
ATM CE
ATM
ATM PE
FR PE
Frame Relay
Frame Relay Header Q.922 Address Ctrl (03 | Pad(03) NL PD (80) | OUT (00) OUT (80-C2) PID (00-007) MAC Header DA SA
FR CE
ATM Header LLC (AA-AA) LLC (03) OU I (00) CUI (80-C2) PID (00-007) PAD (00-00) MAC Header DA SA Ethertype 81-00 VLAN Tag Type/Length Remainder of MAC Frame CPCS-UU CPI Length CRC
Tunnel Label VC Label Control Word MAC Header DA SA Ethertype 81-00 VLAN Tag Type/Length Remainder of MAC Frame
Tunnel Label VC Label Control Word MAC Header DA SA Ethertype 81-00 VLAN Tag Type/Length Remainder of MAC Frame
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal no ip domain lookup mpls label range minimum-value maximum-value [static minimum-static-value maximum-static-value] mpls label protocol ldp mpls ip default-route mpls ldp graceful-restart xconnect logging pseudowire status pseudowire-class [pw-class-name]
10. encapsulation mpls 11. interworking ethernet 12. exit 13. interface loopback loopback-interface-number 14. ip address ip-address mask 15. exit 16. interface GigabitEthernet slot/subslot/port 17. ip address ip-address mask 18. negotiation auto 19. mpls ip 20. exit 21. interface atm slot/subslot/port 22. no ip address 23. atm clock internal 24. no atm enable-ilmi-trap 25. exit 26. interface atm slot/subslot/port [.subinterface-number {point-to-point}] 27. mtu bytes 28. no atm enable-ilmi-trap 29. pvc [name] vpi/vci l2transport 30. encapsulation encapsulation-type
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
31. xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name 32. exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3 Step 4
Router(config)# no ip domain lookup mpls label range minimum-value maximum-value [static minimum-static-value maximum-static-value]
Disables the IP domain naming system (DNS). Configures the range of local labels available for use with Multiprotocol Label Switching (MPLS) applications on packet interfaces.
Example:
Router(config)# mpls label range 101 4000 static 4001 5001
Step 5
Example:
Router(config)# mpls label protocol ldp
Step 6
mpls ip default-route
Example:
Router(config)# mpls ip default-route
Step 7
Example:
Router(config)# mpls ldp graceful-restart
Step 8
Example:
Router(config)# xconnect logging pseudowire status
Step 9
pseudowire-class [pw-class-name]
Example:
Router(config)# pseudowire-class atm-fr-bridged
Establishes a pseudowire class with a name that you specify, and enters the pseudowire class configuration mode. Enables MPLS encapsulation on the interface.
Step 10
encapsulation mpls
Example:
Router(config-pw-class)# encapsulation mpls
Step 11
interworking ethernet
Example:
Router(config-pw-class)# interworking ethernet
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
Command or Action
Step 12 Step 13
exit interface loopback loopback-interface-number
Purpose Exits the pseudowire class configuration mode. Specifies the loopback logical interface.
Example:
Router(config)# interface loopback 0
Step 14
Step 15 Step 16
Exits the interface configuration mode. Specifies the Gigabit Ethernet interface for the connection of the PE routers.
Example:
Router(config)# interface GigabitEthernet 0/0/1
Step 17
Example:
Router(config-if)# ip address 10.10.1.2 255.255.255.0
Step 18
negotiation auto
Example:
Router(config-if)# negotiation auto
Enables the auto negotiation protocol to configure the speed, duplex, and automatic flow control of the Gigabit Ethernet interface. Enables MPLS forwarding of the IPv4 packets towards the MPLS core.
Step 19
mpls ip
Example:
Router(config-if)# mpls ip
Step 20 Step 21
Exits the interface configuration mode. Configures an ATM interface and enters the interface configuration mode.
Example:
Router(config)# interface atm 0/1/2
Step 22
no ip address
Example:
Router(config-if)# no ip address
Step 23
Example:
Router(config-if)# atm clock internal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
Command or Action
Step 24
no atm enable-ilmi-trap
Purpose Disables the Integrated Local Management Interface (ILMI) ATM traps.
Example:
Router(config-if)# no atm enable-ilmi-trap
Step 25 Step 26
Exits the interface configuration mode. Configures an ATM interface and enters the interface configuration mode.
Example:
Router(config)# interface atm 0/1/2.1 point-to-point
Step 27
mtu bytes
Adjusts the maximum packet size or maximum transmission unit (MTU) size.
Note
Example:
Router(config-subif)# mtu 1500
Step 28
no atm enable-ilmi-trap
Example:
Router(config-subif)# no atm enable-ilmi-trap
Step 29
Example:
Router(config-subif)# pvc cisco 10/100 l2transport
Assigns a name to an ATM PVC, specifies the encapsulation type on an ATM PVC, and enters the ATM virtual circuit configuration mode. Sets the AAL5SNAP encapsulation (Any-to-Any) for the ATM point-to-point interface.
Step 30
encapsulation encapsulation-type
Example:
Router(config-if-atm-l2trans-pvc)# encapsulation aal5snap
Step 31
Binds an attachment circuit to a pseudowire and configures an Any Transport over MPLS (AToM) static pseudowire.
Example:
Router(config-if-atm-l2trans-pvc)# xconnect 190.1.1.1 100 encapsulation mpls pw-class atm-fr-bridged
Step 32
exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
pseudowire-class atm-fr-bridged encapsulation mpls interworking ethernet ! interface Loopback0 ip address 44.1.1.2 255.255.255.255 ! interface GigabitEthernet0/0/1 ip address 10.10.1.2 255.255.255.0 negotiation auto mpls ip ! interface ATM0/1/2 no ip address atm clock INTERNAL no atm enable-ilmi-trap ! interface ATM0/1/2.1 point-to-point mtu 1500 no atm enable-ilmi-trap pvc 10/100 l2transport encapsulation aal5snap xconnect 190.1.1.1 100 pw-class atm-fr-bridged ! !
To configure the Frame Relay-to-ATM Bridged Interworking feature on a Frame Relay PE router, perform the following steps:
Note
The following configuration uses a channelized T1/E1 interface. Frame Relay can be configured on other interfaces such as Packet over SONET (PoS) as well.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal (Optional) ipv6 unicast-routing mpls label protocol ldp mpls ip default-route mpls ldp graceful-restart frame-relay switching xconnect logging pseudowire status controller t1 slot/subslot/port
10. framing esf 11. clock source internal 12. linecode b8zs 13. cablelength long db-loss-value 14. channel-group channel-group-number timeslots range 15. exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
16. pseudowire-class [pw-class-name] 17. encapsulation mpls 18. interworking ethernet 19. exit 20. interface loopback loopback-interface-number 21. ip address ip-address mask 22. exit 23. interface serial slot/subslot/port:timeslot 24. no ip address 25. encapsulation frame-relay 26. frame-relay intf-type dce 27. frame-relay interface-dlci dlci switched 28. exit 29. interface GigabitEthernet slot/subslot/port 30. ip address ip-address mask 31. negotiation auto 32. mpls ip 33. exit 34. connect connection-name interface dlci l2transport 35. xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name 36. exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
ipv6 unicast-routing
Example:
Router# ipv6 unicast-routing
Step 4
Specifies the label distribution protocol (LDP) for the Frame Relay PE router.
Example:
Router(config)# mpls label protocol ldp
Step 5
mpls ip default-route
Example:
Router(config)# mpls ip default-route
Step 6
Example:
Router(config)# mpls ldp graceful-restart
Step 7
frame-relay switching
Enables PVC switching on a Frame Relay data circuit-terminating equipment (DCE) device.
Example:
Router(config)# frame-relay switching
Step 8
Example:
Router(config)# xconnect logging pseudowire status
Step 9
controller t1 slot/subslot/port
Example:
Router(config)# controller T1 0/3/0
Step 10
framing esf
Example:
Router(config-controller)# framing esf
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
Command or Action
Step 11
clock source internal
Purpose Configures the clock source of a DS1 link and uses the internal clock from the interface.
Example:
Router(config-controller)# clock source internal
Step 12
linecode b8zs
Specifies Binary 8-Zero Substitution (B8ZS) as the line code type for the T1 controller.
Example:
Router(config-controller)# linecode b8zs
Step 13
Example:
Router(config-controller)# cablelength long 0db
Step 14
Example:
Router(config-controller)# channel-group 0 timeslots 1-24
Step 15 Step 16
Exits the pseudowire class configuration mode. Establishes a pseudowire class with a name that you specify and enters the pseudowire class configuration mode. Enables MPLS encapsulation on the interface.
Example:
Router(config)# pseudowire-class atm-fr-bridged
Step 17
encapsulation mpls
Example:
Router(config-pw-class)# encapsulation mpls
Step 18
interworking ethernet
Example:
Router(config-pw-class)# interworking ethernet
Step 19 Step 20
Exits the pseudowire class configuration mode. Specifies the Loopback logical interface.
Example:
Router(config)# interface loopback 0
Step 21
Example:
Router(config-if)# ip address 44.1.1.2 255.255.255.255
Step 22
exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
Command or Action
Step 23
interface serial slot/subslot/port:timeslot
Example:
Router(config)# interface Serial0/3/0:0
Step 24
no ip address
Example:
Router(config-if)# no ip address
Step 25
encapsulation frame-relay
Example:
Router(config-if)# encapsulation frame-relay
Step 26
Configures a Frame Relay switch type. The router functions as a switch connected to a router.
Example:
Router(config-if)# frame-relay intf-type dce
Step 27
Assigns a data-link connection identifier (DLCI) to a specified Frame Relay subinterface on the router.
Example:
Router(config-if)# frame-relay interface-dlci 101 switched
Step 28 Step 29
Exits the interface configuration mode. Specifies the Gigabit Ethernet interface for the connection of the PE routers.
Example:
Router(config)# interface GigabitEthernet 0/0/1
Step 30
Example:
Router(config-if)# ip address 10.10.1.2 255.255.255.0
Step 31
negotiation auto
Example:
Router(config-if)# negotiation auto
Enables the auto negotiation protocol to configure the speed, duplex, and automatic flow control of the Gigabit Ethernet interface. Enables MPLS forwarding of the IPv4 packets towards the MPLS core.
Step 32
mpls ip
Example:
Router(config-if)# mpls ip
Step 33
exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
Configuring MPLS Layer 2 VPNs Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking
Command or Action
Step 34
connect connection-name interface dlci l2transport
Example:
Router(config)# connect fr-atm-2 Serial0/3/0:0 101 l2transport
Step 35
Example:
Router(config-conn)# xconnect 190.1.1.1 100 encapsulation mpls pw-class atm-fr-bridged
Step 36
exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
Configuring MPLS Layer 2 VPNs Gigabit EtherChannel for Virtual Private Wire Service
Supported Modes
The following modes are supported in the GEC for VPWS feature:
EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking, page 27 EtherChannel-to-EtherChannel over MPLS (Routed) Interworking, page 29
Topology of the GEC Like-to-Like Mode for the GEC for VPWS Feature
Figure 5
Xconnect
MPLS
GEC-CE1
Customer Site
GEC-CE2
Customer Site
332075
GEC-PE1 ASR1K
GEC-PE2 ASR1K
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
25
Configuring MPLS Layer 2 VPNs Gigabit EtherChannel for Virtual Private Wire Service
Any-to-GEC Mode
The Any-to-GEC mode allows switching of data between two physical interfaces in which the two segments, CE1-PE1 and CE2-PE2, are both of different types, while one is GEC, the other can be PPP, Ethernet, Frame Relay, or ATM, as shown in Figure 6. The Any-to-GEC mode has the following features:
Any-to-EtherChannel over MPLS (Bridged) Interworking, page 32 Any-to-EtherChannel over MPLS (Routed) Interworking, page 34
Topology of the Any-to-GEC Mode for the GEC for VPWS Feature
Figure 6
Xconnect
Customer Site Customer Site
MPLS
GEC-CE2
Note
Bridged interworking is used when Layer 2 (L2) packets are considered without regard for Layer 3 contents. In bridged interworking, Ethernet frames that are extracted from the attachment circuit are sent over the MPLS pseudowire.
Note
Routed interworking is used to carry Layer 3 packets. In routed interworking, IP packets that are extracted from the attachment circuits are sent over the MPLS pseudowire.
GEC for VPWS does not support Q-in-Q encapsulation and remote port shutdown. A maximum four member links are supported under the port channel and a maximum of 64 port channel bundles are supported per router.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
26
332074
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking, page 27 EtherChannel-to-EtherChannel over MPLS (Routed) Interworking, page 29 Any-to-EtherChannel over MPLS (Bridged) Interworking, page 32 Any-to-EtherChannel over MPLS (Routed) Interworking, page 34
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal mpls label protocol ldp interface loopback loopback-interface-number ip address ip-address ip-subnet-mask exit pseudowire-class pw-class-name encapsulation mpls interworking ethernet
10. exit 11. interface port-channel number 12. xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name 13. interface GigabitEthernet slot | subslot | port 14. channel-group port-channel number
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
27
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
DETAILED STEPS
Command or Action
Step 1 Step 2
enable
Purpose Changes the privilege level for the corresponding CLI session. Enters the global configuration mode.
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router# mpls label protocol ldp
Step 4
Specifies the loopback interface, and enters the interface configuration mode.
Example:
Router# interface loopback 1
Step 5
Example:
Router# ip address 10.10.2.1 255.255.255.0
Step 6 Step 7
Exits the interface configuration mode. Specifies the name of a Layer 2 pseudowire class and enters the pseudowire class configuration mode.
Example:
Router(config)# pseudowire-class gec-bridged
Step 8
encapsulation mpls
Example:
Router(config-pw)# encapsulation mpls
Step 9
interworking ethernet
Example:
Router(config-pw)# interworking ethernet
Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame. Exits the xconnect configuration mode. Creates an EtherChannel interface on the Cisco Cable Modem Termination System (CMTS).
Step 10 Step 11
Example:
Router(config)# interface port-channel 1
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
28
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
Command or Action
Step 12
xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name
Purpose Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.
Example:
Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-bridged
Step 13
Specifies the Gigabit Ethernet interface, and enters the interface configuration mode.
Example:
Router(config)# interface GigabitEthernet 0/0/1
Step 14
Example:
Router(config-if) channel-group 1
Note
The EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking mode is also supported under VLAN.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal mpls label protocol ldp interface loopback loopback-interface-number ip address ip-address ip-subnet-mask exit pseudowire-class pw-class-name encapsulation mpls interworking ip
10. exit 11. interface port-channel number 12. xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name 13. interface GigabitEthernet slot | subslot | port 14. channel-group port-channel number
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
29
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
DETAILED STEPS
Command or Action
Step 1 Step 2
enable
Purpose Changes the privilege level for the corresponding CLI session. Enters the global configuration mode.
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router# mpls label protocol ldp
Step 4
Specifies the loopback interface, and enters the interface configuration mode.
Example:
Router# interface loopback 1
Step 5
Example:
Router# ip address 10.10.2.1 255.255.255.0
Step 6 Step 7
Exits the interface configuration mode. Specifies the name of a Layer 2 pseudowire class and enters the pseudowire class configuration mode.
Example:
Router(config)# pseudowire-class gec-bridged
Step 8
encapsulation mpls
Example:
Router(config-pw)# encapsulation mpls
Step 9
interworking ip
Example:
Router(config-pw)# interworking ip
Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped. Exits the xconnect configuration mode. Creates an EtherChannel interface on the Cisco Cable Modem Termination System (CMTS).
Step 10 Step 11
Example:
Router(config)# interface port-channel 1
Step 12
Example:
Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-routed
Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
30
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
Command or Action
Step 13
interface GigabitEthernet slot | subslot | port
Purpose Specifies the Gigabit Ethernet interface, and enters the interface configuration mode.
Example:
Router(config)# interface GigabitEthernet 0/0/1
Step 14
Example:
Router(config-if) channel-group 1
Note
The EtherChannel-to-EtherChannel over MPLS (Routed) Interworking mode is also supported under VLAN.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
31
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
Irrespective of the mode used, in Any-to-EtherChannel over MPLS (Bridged) interworking, configure L2VPN interworking on the upstream interfaces of PE routers. For more information about configuring L2VPN interworking on the PE routers, see L2VPN Interworking Modes, page 2. For information about how to configure Frame Relay or ATM on the downstream interfaces of a PE router, see the Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 14. Meanwhile, perform the steps described in the EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking, page 27, on the downstream interfaces of the other PE router. For the Ethernet-to-EtherChannel mode, perform the steps described in EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking, page 27 on the downstream interfaces of the other PE router. Meanwhile, perform the following steps on the downstream interfaces of the PE routers.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal mpls label protocol ldp interface loopback loopback-interface-number ip address ip-address ip-subnet-mask exit pseudowire-class pw-class-name encapsulation mpls interworking ethernet
10. interface GigabitEthernet slot | subslot | port 11. xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
32
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
DETAILED STEPS
Command or Action
Step 1 Step 2
enable
Purpose Changes the privilege level for the corresponding CLI session. Enters the global configuration mode.
configure terminal
Example:
Router# configure terminal
Step 3
Example:
Router# mpls label protocol ldp
Step 4
Specifies the loopback interface, and enters the interface configuration mode.
Example:
Router# interface loopback 1
Step 5
Example:
Router# ip address 10.10.2.1 255.255.255.0
Step 6 Step 7
Exits the interface configuration mode. Specifies the name of a Layer 2 pseudowire class and enters the pseudowire class configuration mode.
Example:
Router(config)# pseudowire-class gec-bridged
Step 8
encapsulation mpls
Example:
Router(config-pw)# encapsulation mpls
Step 9
interworking ethernet
Example:
Router(config-pw)# interworking ethernet
Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame. Specifies the Gigabit Ethernet interface, and enters the interface configuration mode.
Step 10
Example:
Router(config)# interface GigabitEthernet 0/0/1
Step 11
Example:
Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-bridged
Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
33
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
Note
Ethernet-to-EtherChannel over MPLS (Bridge) Interworking mode is also supported under VLAN.
Configure L2VPN interworking on the upstream interfaces of PE routers. For more information about configuring L2VPN interworking on the PE routers, see L2VPN Interworking Modes, page 2. For information about how to configure ATM on the downstream interfaces of a PE router, see the Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 14. Meanwhile, perform the steps described in the EtherChannel-to-EtherChannel over MPLS (Routed) Interworking, page 29, on the downstream interfaces of the other PE router. For the Ethernet-to-EtherChannel mode, see the Any-to-EtherChannel over MPLS (Bridged) Interworking, page 32. For the PPP-to-EtherChannel mode, perform the steps described in the EtherChannel-to-EtherChannel over MPLS (Routed) Interworking, page 29, on the downstream interfaces of the other PE router. Meanwhile, perform the following steps on the downstream interfaces of the PE routers.
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal (Optional) ipv6 unicast-routing mpls ip default-route mpls ldp graceful-restart xconnect logging pseudowire status controller t1 slot | subslot | port clock source internal linecode b8zs
10. cablelength long db-loss-value 11. channel-group channel-group-number timeslots range 12. exit 13. pseudowire-class pw-class-name 14. encapsulation mpls 15. interworking ethernet 16. exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
34
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
17. interface loopback loopback-interface-number 18. ip address ip-address mask 19. exit 20. interface serial slot | subslot | port:timeslot 21. no ip address 22. encapsulation ppp 23. clock source internal 24. xconnect vc-id pw-class pw-class pw-class-name 25. xconnect peer-loopback vc-id pw-class pe-class-name
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
35
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
DETAILED STEPS
Command or Action
Step 1
enable
Purpose Enables the privileged EXEC mode. Enter your password, if prompted.
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
ipv6 unicast-routing
Example:
Router# ipv6 unicast-routing
Step 4
mpls ip default-route
Example:
Router(config)# mpls ip default-route
Step 5
Example:
Router(config)# mpls ldp graceful-restart
Step 6
Example:
Router(config)# xconnect logging pseudowire status
Step 7
controller t1 slot/subslot/port
Example:
Router(config)# controller T1 0/3/0
Step 8
Configures the clock source of a DS1 link and uses the internal clock from the interface.
Example:
Router(config-controller)# clock source internal
Step 9
linecode b8zs
Specifies Binary 8-Zero Substitution (B8ZS) as the line code type for the T1 controller.
Example:
Router(config-controller)# linecode b8zs
Step 10
Example:
Router(config-controller)# cablelength long 0db
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
36
Configuring MPLS Layer 2 VPNs Configuring Gigabit EtherChannel for Virtual Private Wire Service
Command or Action
Step 11
channel-group channel-group-number timeslots range
Example:
Router(config-controller)# channel-group 0 timeslots 1-24
Step 12 Step 13
Exits the pseudowire class configuration mode. Establishes a pseudowire class with a name that you specify and enters the pseudowire class configuration mode. Enables MPLS encapsulation on the interface.
Example:
Router(config)# pseudowire-class atm-fr-bridged
Step 14
encapsulation mpls
Example:
Router(config-pw-class)# encapsulation mpls
Step 15
interworking ethernet
Example:
Router(config-pw-class)# interworking ethernet
Step 16 Step 17
Exits the pseudowire class configuration mode. Specifies the Loopback logical interface.
Example:
Router(config)# interface loopback 0
Step 18
Example:
Router(config-if)# ip address 44.1.1.2 255.255.255.255
Step 19 Step 20
Exits the interface configuration mode. Specifies a serial interface created on a channelized T1 controller.
Example:
Router(config)# interface Serial0/3/0:0
Step 21
no ip address
Example:
Router(config-if)# no ip address
Step 22
encapsulation ppp
Example:
Router(config-if)# encapsulation frame-relay
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
37
Command or Action
Step 23 Step 24
clock source internal
Purpose Specifies that the T1/E1 link uses the internal clock from the interface. Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.
Note
Ethernet-to-EtherChannel over MPLS (Bridge) Interworking mode is also supported under VLAN.
Additional References
The following sections provide references related to the Frame Relay to ATM Bridged Interworking and xconnect support on GEC (VPWS) features.
Related Documents
Related Topic Cisco IOS commands Basics of MPLS MPLS Layer 2 VPNs Cisco IOS Configuration Fundamentals Document Title Cisco IOS Master Commands List, All Releases MPLS: Basic MPLS Configuration Guide, Cisco IOS XE Release 3S MPLS Layer 2 VPNs Configuration Guide, Cisco IOS XE Release 3S Cisco IOS Configuration Fundamentals Command Reference
Standards
Standard No new or modified standards are supported by this feature. Title
MIBs
MIB
MIBs Link CISCO-IETF-PW-MIB CISCO-IETF-PW-MPLS-MIB To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use the Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
38
Configuring MPLS Layer 2 VPNs Feature Information for Configuring MPLS Layer 2 VPNs
RFCs
RFC1 RFC 2684 RFC 2427
1. Not all the supported RFCs are listed.
Title Multiprotocol Encapsulation over ATM Adaptation Layer 5 Multiprotocol Interconnect over Frame Relay
Technical Assistance
Description The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. Link http://www.cisco.com/cisco/web/support/index.html
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
39
Configuring MPLS Layer 2 VPNs Feature Information for Configuring MPLS Layer 2 VPNs
Table 2
Releases 3.6.0S
Feature Information The Frame Relay to ATM Bridged Interworking feature provides interoperability between the Frame Relay attachment VC and the ATM attachment VC connected to different PE routers. The bridged encapsulation corresponding to the bridged (Ethernet) interworking mechanism is used. The Ethernet frames are carried through the MPLS network using Ethernet over MPLS (EoMPLS). In Cisco IOS XE Release 3.6.0S, this feature was implemented on the ASR 1000 Series Aggregation Services Routers. The following sections provide information about this feature:
Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 12 Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking, page 14
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
40
Configuring MPLS Layer 2 VPNs Feature Information for Configuring MPLS Layer 2 VPNs
Table 2
Releases 3.6.0S
Feature Information The Xconnect Support on GEC (VPWS) on ASR1000 feature enables the service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructurea Cisco MPLS network. Instead of separate networks with network management environments, service providers can deliver Layer 2 connections over an MPLS backbone. In Cisco IOS XE Release 3.6.0S, this feature was implemented on the ASR 1000 Series Aggregation Services Routers. The following sections provide information about this feature:
Gigabit EtherChannel for Virtual Private Wire Service, page 25 Configuring Gigabit EtherChannel for Virtual Private Wire Service, page 27
3.8.0S
Reverse L2GP (R-L2GP) is a variation of L2GP. In case of R-L2GP, the pseudo information of the R-L2GP is transmitted by nPEs, instead of uPEs. R-L2GP provides a mechanism to send out static preconfigured BPDUs on each ring access port of nPEs to stimulate a per-access ring instantiation of the protocol. R-L2GP enables the PEs to avoid the burden of running Multiple-instance Spanning Tree Protocol (MST) when multiple independent access networks that run MST connect to a pair of redundant PEs. In order for this to work, the pair of nPEs are programmed to send out BPDUs on the access ring ports in such a way that they appear to be either:
The root bridge itself (the bridge with the lowest bridge id/priority). The bridge with the second lowest bridge ID/priority, and with a 0 cost path to the root.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
41
Glossary
ATMAsynchronous Transfer Mode. A method of data transportation, whereby fixed-length packets are sent over a switched network. The methods ability to ensure reliable delivery of packets at a high rate makes it suitable for carrying voice, video, and data. AToMAny Transport over MPLS. AToM is a solution for transporting Layer 2 packets over an MPLS backbone. AToM enables service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructurea Cisco MPLS network. Instead of separate networks with separate network management environments, service providers can deliver Layer 2 connections over an MPLS backbone. EoMPLSEthernet over MPLS. This technology leverages an existing MPLS backbone network to deliver Transparent LAN Services based on Ethernet connectivity to the customer site. GECGigabit EtherChannel. A high-performance Ethernet technology that provides gigabit per second transmission rates. It provides a flexible and scalable bandwidth with resiliency and load sharing across links for switches, router interfaces, and servers. Supports up to eight links per channel. MPLSMultiprotocol Label Switching. A mechanism in high-performance telecommunications networks that directs and carries data from one network node to the next. MPLS makes it easy to create virtual links between distant nodes. It can encapsulate packets of various network protocols. VPLSVirtual Private LAN Service. A method to provide Ethernet-based multipoint-to-multipoint communication over IP and MPLS networks.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. 2013 Cisco Systems, Inc. All rights reserved.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
42
The Label Switched Multicast (LSM) feature supports IPv4 and IPv6 multicast traffic over a Multi-Protocol Label Switching (MPLS) network. This feature is based on the basic MPLS infrastructure and supports IP multicast traffic through the MPLS clouds. The LSM feature enables service providers to extend the existing MPLS backbone network for multicast services. By default, MPLS creates an out-label for an in-label for each packet. This feature extends this functionality to create multiple out-labels for a single in-label. The LSM service includes point-to-multipoint (P2MP) and multipoint-to-multipoint (MP2MP) packet transport. The P2MP packet transport can be implemented using either Resource reSerVation Protocol (RSVP) P2MP - Traffic Engineering (P2MP-TE), or Multicast Label Distribution Protocol (MLDP) based Multicast VPN (MVPN). The MP2MP packet transport can be implemented only through MLDP based MVPN. The packets are transported over three types of routers:
Head-end router: Encapsulates the IP packet with one or more labels. Midpoint router: Replaces the in-label with an out-label. Tail-end router: Removes the label from the packet.
A head-end router does not support multiple sub Label Switched Paths (subLSPs) belonging to different tunnels, over the same physical interface. RSVP-TE-based LSM is not supported; only MLDP-based LSM is supported. Process-level software forwarding is not supported. Rosen Model MLDP is not supported in the global configuration mode. However, MLDP inband signaling is supported in the global configuration mode. These are the scale considerations for MLDP-based MVPN:
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
600.
Maximum number of m-route supported on each PE is 200,000. Maximum number of OIF supported is 1000. Maximum number of MLDP ingress labels (local labels) supported on each PE is 100,000. Maximum number of MLDP egress labels (remote labels) supported on each PE is 100,000. Max of 32 PE or P neighbors in a PE router per MDT, and max of 33 PE or P neighbors in a P
Supported content group modes are Protocol Independent Multicast (PIM) sparse mode (PIM-SM) and Source Specific Multicast (SSM) traffic. Unsupported content group modes are PIM dense mode (PIM-DM) and bidirectional PIM (bidir-PIM) traffic. The PIM-sparse content group mode is supported if the RP is configured behind the PE router (on CE). The RP and the source router have to be in the same VRF and PE site with the same RPF interface. For RPF lookup in the context of the extranet, only the ip multicast rpf select command is supported for the configuration. The MLDP provides only link protection with the FRR TE. Only single hop is supported with MLDP TE. However, the backup path can have multiple hops.
Note
Before configuring MLDP-based MVPN, ensure that the MPLS is enabled on the core facing interface. For information on MPLS configuration, see the Cisco IOS Multiprotocol Label Switching Configuration Guide. Also, ensure that the BGP and any interior gateway protocol (OSPF or ISIS) is enabled on the core router.
Enabling MPLS MLDP Configuring MVPN Routing and Forwarding instance Configuring a VRF entry
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring the route distinguisher Configuring VPN Id Configuring the Route-Target extended community Configuring the default MDT Configuring Data MDTs (optional) Configuring BGP MDT address family Configuring BGP vpnv4 address family Configuring BGP VRF address family Configuring PIM SM/SSM mode for the VRFs
SUMMARY STEPS
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal mpls MLDP vrf definition vrf-name rd route-distinguisher vpn id vpn_id route-target [import | export | both] route-target-ext-community route-target [import | export | both] route-target-ext-community mdt default mpls MLDP root-node
10. mdt data mpls MLDP numberofdataMDTs 11. mdt data threshold bandwidth 12. exit 13. ip multicast-routing vrf vrf-name distributed 14. end
Note
See Configuring the MDT Address Family in BGP for Multicast VPN for information on configuring an MDT and vpnv4 address family session on the PE routers to establish MDT peering sessions for MVPN.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
DETAILED STEPS
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
mpls MLDP
Example:
Router(config)# mpls MLDP
Note
The mpls MLDP command is configured by default. To disable MPLS MLDP, use the no mpls MLDP command.
Step 4
Defines the VPN routing instance by assigning a VRF name, and enters the VRF configuration mode. The vrf-name argument is the name assigned to a VRF.
Example:
Router(config)# ip vrf blue
Step 5
rd route-distinguisher
Example:
Router(config-vrf)# rd 10:3
Creates routing and forwarding tables. Specify the route-distinguisher argument to add an 8-byte value to create a VPN prefix. You can enter an route-distinguisher value in either of these formats:
16-bit autonomous system number: Your 16-bit number. For example, 101:3. 32-bit IP address: Your 32-bit number. For example, 192.168.122.15:1.
Step 6
vpn id vpn-id
Example:
Router(config-vrf)# vpn id 10:3
Step 7
The import keyword imports the routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target import 10:3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 8
route-target export route-target-ext-community
The export keyword exports the routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target export 10:3
Step 9
Example:
Router(config-vrf)# mdt default mpls MLDP 2.2.2.2
Configures MLDP MDT for a VRF. The root node can be IP address of a loopback or physical interface on any router (source PE, receiver PE or core router) in the provider network. The root node address should be reachable by all the routers in the network. The router from where the signalling occurs functions as the root node. The default MDT must be configured on each PE router to enable the PE routers to receive multicast traffic for this particular MVRF.
Note
By default MPLS MLDP is enabled. To disable, use the no mpls MLDP command.
Note
LSPVIF tunnel is created as a result of mdt default mpls MLDP root-node command.
Step 10
Example:
Router(config-vrf)# mdt data mpls MLDP 100
Step 11
Example:
Router(config-vrf)# mdt data threshold 20
Note
Step 12
exit
Example:
Router(config-vrf)# exit
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 13
ip multicast-routing vrf vrf-name distributed
Example:
Router(config)# ip multicast-routing vrf blue distributed
Step 14
end
Example:
Router(config)# end
Note
See Configuring the MDT Address Family in BGP for Multicast VPN for information on configuring an MDT address family session on the PE routers to establish MDT peering sessions for MVPN.
Example
This example describes how to configure MLDP MVPN on an intranet:
Router> enable Router# configure terminal Router(config)# mpls MLDP Router(config)# ip vrf blue Router(config-vrf)# rd 10:3 Router(config-vrf)# vpn id 10:3 Router(config-vrf)# route-target import 10:3 Router(config-vrf)# route-target export 10:3 Router(config-vrf)# mdt default mpls MLDP 2.2.2.2 Router(config-vrf)# mdt data mpls MLDP 100 Router(config-vrf)# mdt data threshold 20 Router(config-vrf)# exit Router(config)# ip multicast-routing vrf blue distributed Router(config)# end
Verification
Use these commands to verify the LSM-MLDP-based MVPN support intranet configuration.
To check the MLDP neighbors, use the show mpls MLDP neighbors command:
Router# show mpls MLDP neighbors MLDP peer ID : 3.3.3.3:0, uptime 00:41:41 Up, Target Adj : Yes Session hndl : 2 Upstream count : 2 Branch count : 0 Path count : 1 Path(s) : 3.3.3.3 No LDP Tunnel20 Nhop count : 1 Nhop list : 3.3.3.3 MLDP peer ID Target Adj Session hndl : 2.2.2.2:0, uptime 00:17:42 Up, : No : 4
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
: : : : :
0 0 1 3.3.3.3 0
No LDP Tunnel20
To check the PIM neighbors, use the show ip pim vrf vrf-name neighbor command:
Router# show ip pim vrf blue neighbor PIM Neighbor Table Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority, P - Proxy Capable, S - State Refresh Capable, G - GenID Capable Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 3.3.3.3 Lspvif1 00:06:21/00:01:17 v2 1 / DR S P G
To check the multicast routes for a given VRF, use show ip mroute vrf vrf_name verbose command:
Router# show ip mroute vrf blue verbose IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, V - RD & Vector, v - Vector Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (40.0.0.2, 232.0.1.4), 00:00:16/00:03:13, flags: sT Incoming interface: GigabitEthernet3/2/1, RPF nbr 0.0.0.0 Outgoing interface list: Lspvif1, LSM MDT: B0000004 (default), Forward/Sparse, 00:00:16/00:03:13 (*, 224.0.1.40), 00:47:09/00:02:56, RP 0.0.0.0, flags: DPL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null
To check the packet counters, use show ip mroute vrf vrf_name count command:
Router# show ip mroute vrf blue count IP Multicast Statistics 2 routes using 1208 bytes of memory 2 groups, 0.50 average sources per group Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second Other counts: Total/RPF failed/Other drops(OIF-null, rate-limit etc) Group: 232.0.1.4, Source count: 1, Packets forwarded: 1333, Packets received: 1334 Source: 40.0.0.2/32, Forwarding: 1333/20/46/7, Other: 1334/0/1 Group: 224.0.1.40, Source count: 0, Packets forwarded: 0, Packets received: 0
interface
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
No Label [mdt 55:1111 0][V] \9422 aggregate/red No Label [mdt 55:2222 0][V] \9708 aggregate/blue Forwarding through a LSP tunnel. View additional labelling info with the 'detail' option
Source-Side Chaining (SSC): Configure the phantom receiver MVRF on the source-side router. Multicast routes with VRF Reverse Path Forwarding (RPF) loopup should be configured on the source PE. Receiver-Side Chaining (RSC): Configure the phantom source MVRF on the receiver-side router. Multicast routes with VRF RPF loopup should be configured on the receiver VRF.
Configuring receiver MVRF on the source PE. Configuring a loopback address in the receiver VRF on the source PE. Configuring fallback multicast route for source address on source PE. Configuring fallback multicast route for RP address on the source PE in case of SM mode. Configuring static multicast route on recevier PE for loopback IP in the receiver VRF configured on the source PE.
Note
This configuration is based on illustration Figure 1. Configure multicast routes on the PE1 router.
Figure 1 MLDP Based MVPN Network
CE4 L1 IPv4 L2
P IPv4
L3
IPv4
CE5
PE1 IPv4
L4
IPv4
PE3 IPv4
CE3
CE2 Receiver1
SUMMARY STEPS
The followings are the summary steps to configure MLDP MVPN for Extranet using SSC.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
enable configure terminal vrf definition vrf-name rd route-distinguisher vpn id vpn_id route-target import route-target-ext-community route-target import route-target-ext-community mdt default mpls MLDP root-node end
10. interface type instance 11. ip vrf forwarding vrf-name 12. ip address ip-address subnet 13. exit 14. ip multicast [vrf receiver-vrf-name] rpf select {global | vrf source-vrf-name} group-list access-list 15. end
enable configure terminal vrf definition vrf-name rd route-distinguisher vpn id vpn_id route-target import route-target-ext-community route-target import route-target-ext-community mdt default mpls MLDP root-node end
10. interface type instance 11. ip vrf forwarding vrf-name 12. ip address ip-address subnet 13. exit 14. ip mroute vrf receiver_vrf source_address subnet_mask loopback_ip 15. end
DETAILED STEPS
The followings are the detailed steps to configure MLDP MVPN for Extranet using SSC.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Defines the VPN routing instance by assigning a VRF name argument, and enters the VRF configuration mode. The vrf-name argument is the name assigned to a VRF. Creates routing and forwarding tables. Specify the route-distinguisher argument to add an 8-byte value to create a VPN prefix. You can enter an route-distinguisher value in either of these formats:
Example:
Router(config)# vrf definition blue
Step 4
rd route-distinguisher
Example:
Router(config-if)# rd 10:4
16-bit autonomous system number: Your 16-bit number. For example, 101:3. 32-bit IP address: Your 32-bit number. For example, 192.168.122.15:1.
Step 5
vpn id vpn-id
Example:
Router(config-if)# vpn id 10:4
Step 6
The import keyword imports the routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities. The export keyword export the routing information to the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target import 10:4
Step 7
Example:
Router(config-vrf)# route-target export 10:4
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
Command
Step 8
mdt default mpls MLDP root-node
Example:
Router(config-vrf)# mdt default mpls MLDP 2.2.2.2
Note
Step 9
end
Example:
Router(config-vrf)# end
Step 10
Enters interface configuration mode and names the new loopback interface.
Example:
Router(config)# interface loopback 3
Step 11
Example:
Router(config-if)# ip vrf forwarding red
Step 12
ip-address specifies the IP address of the interface. subnet-mask specifies the subnet mask of the interface.
Example:
Router(config-if)# ip address 1.1.1.1 255.255.255.255
Step 13 Step 14
exit ip multicast [vrf receiver-vrf-name] rpf select {global | vrf source-vrf-name} group-list access-list
Exits the interface configuration mode. Configures Reverse Path Forwarding (RPF) lookups originating in a receiver Multicast VPN (MVPN) routing and forwarding (MVRF) instance, in the global routing table to be performed in a source MVRF instance, or in the global routing table based on group address. The optional vrf keyword and receiver-vrf-name argument are used to apply a group-based VRF selection policy to RPF lookups originating in the VRF specified for the receiver-vrf-name argument. If the optional vrf keyword and receiver-vrf-name argument are not specified, the group-based VRF selection policy applies to RPF lookups originating from the global table. Closes the configuration session.
Example:
Router(config)# ip multicast vrf red rpf select vrf blue
Step 15
end
Example:
Router(config-vrf)# end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
11
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Defines the VPN routing instance by assigning a VRF name, and enters the VRF configuration mode. The vrf-name argument is the name assigned to a VRF. Creates routing and forwarding tables. Specify the route-distinguisher argument to add an 8-byte value to create a VPN prefix. You can enter an RD value in either of these formats:
Example:
Router(config)# vrf definition blue
Step 4
rd route-distinguisher
Example:
Router(config-if)# rd 10:4
16-bit autonomous system number: Your 16-bit number. For example, 101:3. 32-bit IP address: Your 32-bit IP address. For example, 192.168.122.15:1.
Step 5
vpn id vpn-id
Example:
Router(config-if)# vpn id 10:4
Step 6
The import keyword imports the routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities. The export keyword exports the routing information to the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target import 10:4
Step 7
Example:
Router(config-vrf)# route-target export 10:4
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
12
Command
Step 8
mdt default mpls MLDP root-node
Example:
Router(config-vrf)# mdt default mpls MLDP 2.2.2.2
Note
Step 9
end
Example:
Router(config-vrf)# end
Step 10
Enters interface configuration mode and names the new loopback interface.
Example:
Router(config)# interface loopback 3
Step 11
Example:
Router(config-if)# ip vrf forwarding blue
Step 12
ip-address specifies the IP address of the interface. subnet-mask specifies the subnet mask of the interface.
Example:
Router(config-if)# ip address 3.3.3.3 255.255.255.255
Step 13 Step 14
Exits the interface configuration mode. Configures the static multicast routes for source addresses in the reciever VRF, where: loopback ip is ip address of the loopback configured in the recevier VRF in the source PE.
Example:
Router(config-if)# ip mroute vrf red 40.0.0.0 255.255.255.0 1.1.1.1
Step 15
end
Example:
Router(config-vrf)# end
Example
This is sample example for configuring MLDP MVPN for configuring extranet using SSC:
Configuration on the Source PE(Configure These Steps for Both Red and Blue VRFs)
Router> enable Router# configure terminal Router(config)# ip vrf blue Router(config-if)# rd 10:4 Router(config-if)# vpn id 10:4
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
13
Router(config-vrf)# route-target import 10:4 Router(config-vrf)# route-target export 10:4 Router(config-vrf)# mdt default mpls MLDP 2.2.2.2 Router(config-vrf)# end Router(config)# interface loopback 3 Router(config-if)# ip vrf forwarding red Router(config-if)# ip address 1.1.1.1 255.255.255.255 Router(config)# ip mroute vrf red 40.0.0.0 255.255.255.0 fallback-lookup vrf blue Router(config)# ip mroute vrf red 44.44.44.44 255.255.255.0 fallback-lookup vrf blue Router(config-vrf)# end
Configuring the source mVRF on the receiver PE router. Configuring RPF for MLDP based MVPN extranet support using static multicast routes on the receiver PE.
Note
This configuration is based on illustration Figure 1. Configure multicast routes on PE2 and PE3 routers.
SUMMARY STEPS
Configuration on Source PE:
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal vrf definition vrf-name rd route-distinguisher vpn id vpn_id route-target import route-target-ext-community route-target import route-target-ext-community mdt default mpls MLDP root-node end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
14
Configuration on Receiver PE (Configure these steps for both red and blue VRFs)
1. 2. 3. 4. 5. 6. 7. 8. 9.
enable configure terminal vrf definition vrf-name rd route-distinguisher vpn id vpn_id route-target import route-target-ext-community route-target import route-target-ext-community mdt default mpls MLDP root-node ip mroute [vrf recevier-vrf-name] source-address mask fallback-lookup {global | vrf source-vrf-name} [distance]
10. end
DETAILED STEPS
Configuration on Source PE
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Defines the VPN routing instance by assigning a VRF name, and enters the VRF configuration mode. The vrf-name argument is the name assigned to a VRF. Creates routing and forwarding tables. Specify the route-distinguisher argument to add an 8-byte value to create a VPN prefix. You can enter an RD value in either of these formats:
Example:
Router(config)# ip vrf blue
Step 4
rd route-distinguisher
Example:
Router(config-if)# rd 10:3
16-bit autonomous system number: Your 16-bit number. For example, 101:3. 32-bit IP address: Your 32-bit number. For example, 192.168.122.15:1.
Step 5
vpn id vpn-id
Example:
Router(config-if)# vpn id 10:3
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
15
Command
Step 6
route-target import route-target-ext-community
The import keyword imports routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities. The export keyword exports the routing information to the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target import 10:3
Step 7
Example:
Router(config-vrf)# route-target export 10:3
Step 8
Example:
Router(config-vrf)# mdt default mpls MLDP 2.2.2.2
Note
Step 9
end
Example:
Router(config-vrf)# end
Configuration on Receiver PE
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Defines the VPN routing instance by assigning a VRF name, and enters the VRF configuration mode. The vrf-name argument is the name assigned to a VRF.
Example:
Router(config)# ip vrf blue
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
16
Command
Step 4
rd route-distinguisher
Purpose Creates routing and forwarding tables. Specify the route-distinguisher argument to add an 8-byte value to create a VPN prefix. You can enter an RD value in either of these formats:
Example:
Router(config-if)# rd 10:3
16-bit autonomous system number: Your 16-bit number. For example, 101:3. 32-bit IP address: Your 32-bit number. For example, 192.168.122.15:1.
Step 5
vpn id vpn-id
Example:
Router(config-if)# vpn id 10:3
Step 6
The import keyword imports routing information from the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities. The export keyword exports the routing information to the target VPN extended community. The route-target-ext-community argument adds the route-target extended community attributes to the VRF list of import, export, or both (import and export) route-target extended communities.
Example:
Router(config-vrf)# route-target import 10:3
Step 7
Example:
Router(config-vrf)# route-target export 10:3
Step 8
Example:
Router(config-vrf)# mdt default mpls MLDP 2.2.2.2
Note
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
17
Command
Step 9
ip mroute [vrf receiver-vrf-name] source-address mask {fallback-lookup vrf source-vrf-name} [distance]
Purpose Configures RPF lookups originating in a receiver MVRF or in the global routing table to be resolved in a source MVRF or in the global routing table based on group address. Use this command on the receiver PE.
Example:
Router(config)# ip mroute vrf red 40.0.0.0 255.255.255.0 fallback-lookup vrf blue
The optional vrf keyword and receiver-vrf-name argument are used to apply a group-based VRF selection policy to RPF lookups originating in the VRF specified for the receiver-vrf-name argument. If the optional vrf keyword and receiver-vrf-name argument are not specified, the group-based VRF selection policy applies to RPF lookups originating in the global table.
Step 10
end
Example:
Router(config-vrf)# end
Example
This is sample example for configuring MLDP MVPN for configuring extranet using RSC:
Configuration on Source PE:
Router# enable Router# conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip vrf blue1 Router(config-if)# rd 10:3 Router(config-if)# vpn id 10:3 Router(config-vrf)# route-target import 10:3 Router(config-vrf)# route-target export 10:3 Router(config-vrf)# mdt default mpls MLDP 2.2.2.2 mdt default mpls MLDP root-node Router(config-if)# end Router(config)# ip mroute vrf red 40.0.0.0 255.255.255.0 fallback-lookup vrf blue Router(config-if)# end
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
18
For more information on MPLS TE-FRR, see MPLS Point-to-Multipoint Traffic Engineering.
Summary Steps
1. 2. 3. 4. 5.
enable configure terminal ip multicast mpls traffic-eng [range {access-list-number | access-list-name}] mpls MLDP path traffic-eng end
DETAILED STEPS
Command
Step 1
enable
Example:
Router> enable
Step 2
configure terminal
Example:
Router# configure terminal
Step 3
Enables IP multicast traffic on a tail end router enabled with MPLS TE P2MP functionality.
Example:
Router(config)# ip multicast mpls traffic-eng
Step 4
Example:
Router(config)# mpls MLDP path traffic-en
Step 5
end
Example:
Router(config)# end
For more information, see MPLS Traffic Engineering (TE) - Fast Reroute (FRR) Link and Node Protection.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
19
Verification
Use these commands to verify the LSM-MLDP-based MVPN support configuration.
To check the MLDP neighbors, use the show mpls MLDP neighbors command:
Router# show mpls MLDP neighbors MLDP peer ID : 3.3.3.3:0, uptime 00:41:41 Up, Target Adj : Yes Session hndl : 2 Upstream count : 2 Branch count : 0 Path count : 1 Path(s) : 3.3.3.3 No LDP Tunnel20 Nhop count : 1 Nhop list : 3.3.3.3 MLDP peer ID Target Adj Session hndl Upstream count Branch count Path count Path(s) : : : : : : : 2.2.2.2:0, uptime 00:17:42 Up, No 4 0 0 1 3.3.3.3 No LDP Tunnel20
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
20
Nhop count
: 0
To check the PIM neighbors, use the show ip pim vrf vrf_name neighbor command:
Router# show ip pim vrf blue neighbor PIM Neighbor Table Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority, P - Proxy Capable, S - State Refresh Capable, G - GenID Capable Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode 3.3.3.3 Lspvif1 00:06:21/00:01:17 v2 1 / DR S P G
To check the multicast routes for a given VRF, use show ip mroute vrf vrf_name verbose command:
Router# show ip mroute vrf blue verbose IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, V - RD & Vector, v - Vector Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (40.0.0.2, 232.0.1.4), 00:00:16/00:03:13, flags: sT Incoming interface: GigabitEthernet3/2/1, RPF nbr 0.0.0.0 Outgoing interface list: Lspvif1, LSM MDT: B0000004 (default), Forward/Sparse, 00:00:16/00:03:13 (*, 224.0.1.40), 00:47:09/00:02:56, RP 0.0.0.0, flags: DPL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null
To check the packet counters, use show ip mroute vrf vrf_name count command:
Router# show ip mroute vrf blue count IP Multicast Statistics 2 routes using 1208 bytes of memory 2 groups, 0.50 average sources per group Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second Other counts: Total/RPF failed/Other drops(OIF-null, rate-limit etc) Group: 232.0.1.4, Source count: 1, Packets forwarded: 1333, Packets received: 1334 Source: 40.0.0.2/32, Forwarding: 1333/20/46/7, Other: 1334/0/1 Group: 224.0.1.40, Source count: 0, Packets forwarded: 0, Packets received: 0
To check the MFIB output and whether hardware switching or software switching is enabled, use show ip mfib vrf vrf_name group_address verbose command:
Router# show ip mfib vrf blue 232.0.1.4 verbose Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag, ET - Data Rate Exceeds Threshold, K - Keepalive DDE - Data Driven Event, HW - Hardware Installed I/O Item Flags: IC - Internal Copy, NP - Not platform switched, NS - Negate Signalling, SP - Signal Present, A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward, MA - MFIB Accept Platform per slot HW-Forwarding Counts: Pkt Count/Byte Count Platform Entry flags: HF - Hardware Forwarding, NP - Not platform switched, PF - Partial Hardware Forwarding
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
21
Platform Interface flags: HW - Hardware Switched, NP - Not platform switched Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second Other counts: Total/RPF failed/Other drops I/O Item Counts: FS Pkt Count/PS Pkt Count VRF blue (40.0.0.2,232.0.1.4) Flags: K HW Platform Flags: HW Slot 6: HW Forwarding: 912/41952, Platform Flags: HF SW Forwarding: 0/0/0/0, Other: 1/0/1 HW Forwarding: 912/20/46/7, Other: 0/0/0 GigabitEthernet3/2/1 Flags: RA A MA Platform Flags: Lspvif1, LSM/B0000004 Flags: RF F NS Platform Flags: HW CEF: Mid chain adjacency Pkts: 0/0
To display all the Replicate Output Chain Element (Replicate OCE) on the Forwarding Manager (FMAN) RP, use show platform software mpls rp act-status replicate command.
Router#show platform software mpls rp active replicate Replicate-oce-list: OM: 0x42269b64 Replicate-oce-list: OM: 0x43ba2aec Replicate-oce-list: OM: 0x422659bc Replicate-oce-list: OM: 0x422658ac 0x400000d2 (1 OCEs) 0x400000d3 (1 OCEs) 0x400000d4 (0 OCEs) 0x400000d5 (0 OCEs)
To display the Replicate OCE with the specified index value on FMAN RP, use show platform software mpls rp act-status replicate index index-value command.
Note
You should run "show platform software mpls rp active replicate" first to see the all the replicated OCE on the FMAN RP.
Router#show platform software mpls fp active replicate Replicate-oce-list: 0x84 (1 OCEs) AOM obj: 478, HW list: 0x11b19610 (created) Router#show platform software mpls rp active replicate index 0x84 Replicate-oce-list entries OCE Type Misc Info ------------------------------------------------------------------------------------
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
22
0xa3 (created)
OBJ_LABEL
To display all the replicated OCE on the FMAN FP, use show platform software mpls fp act-status replicate command.
Router#show platform software mpls fp active replicate Replicate-oce-list: 0x400000d2 (1 OCEs) AOM obj: 352887, HW list: 0x11a65628 (created) Replicate-oce-list: 0x400000d3 (1 OCEs) AOM obj: 352889, HW list: 0x10d4a518 (created) Replicate-oce-list: 0x400000d4 (0 OCEs) AOM obj: 352891, HW list: 0x139e3d90 (created) Replicate-oce-list: 0x400000d5 (0 OCEs) AOM obj: 352894, HW list: 0x139e7cb8 (created)
To display the complete OCE chain used for forwarding traffic to a particular IPv4 multicast address, use show platform hardware qfp active feature multicast v4mcast ip-address-mgroup ip-address-source vrf vrf-id extension command.
Router#show platform hardware qfp active feature multicast v4mcast 239.1.1.1/32 vrf 2 extension Root: 0x1187fc58 Flags: 0x000002 First leaf: 0x11887fa8 Number of nodes: 1 Number of leaves: 3 RPF i/f: 0x01fff7 Punt limit counter: 200 NS DCS Punt limit: 0x000001 RPF Fast Convergence Flags: 00000000 Secondary RPF interface: 00000000 RPF Fast Convergence Timer: 0 Extended leaf address: 0x89f80060 Node: 0x1187fc58 Cumulative Free Space: : 4 Cumulative Weight: : 3 Number of Children: : 3 Hw Addr: : 0x8b969440 Node Flags: : 0x000004 Software Child Ptr: : 0x1187fce0, 0x1187fd60, 0x11887fa8, 00000000 00000000, 00000000, 00000000 Hardware Child Ptr: : 0x89f8e440, 0x89f8e450, 0x89f8e460, 00000000 00000000, 00000000, 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11884b48 HW OCE chain ptr: 0x895d59a0 OCE Type: Adjacency, Number of children: 1 Adj Type: : IPV4 Adjacency Encap Len: : 0 L3 MTU: : 9216 Adj Flags: : 64 Fixup Flags: : 0 Interface Name: Lspvif0 Next Hop Address: : 00000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 0x895d5940
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
23
OCE Type: REPLICATE OCE, Number of children: 1 Replica_node: : 0x89fab440 Next HW OCE Ptr: : 0x895d5ab0 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 17 Out Backup Labels: : 0 Next HW OCE Ptr: : 0x895d5a70 OCE Type: Label OCE, Number of children: 1 Label flags: : 65 Num Labels: : 1 Num Bk Labels: : 0 Out Labels: : 3 Next HW OCE Ptr: : 0x895d59f0 OCE Type: Adjacency, Number of children: 0 Adj Type: : MPLS Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 0 Interface Name: GigabitEthernet0/1/0 Encap: : 00 24 14 f4 9d 00 00 21 d8 d4 a5 10 88 47 Next Hop Address: : 0b000002 00000000 00000000 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000002 SW OCE chain ptr: 0x118830d0 HW OCE chain ptr: 0x895d58f0 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV4 Adjacency Encap Len: : 20 L3 MTU: : 1480 Adj Flags: : 0 Fixup Flags: : 2 Interface Name: Tunnel1 Encap: : 45 00 00 00 00 00 00 00 ff 67 39 94 c0 00 01 01 c0 00 01 01 Next Hop Address: : 00000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x1186c250 HW OCE chain ptr: 0x895d5650 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV4 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/2 Encap: : 01 00 5e 00 00 00 00 21 d8 d4 a5 12 08 00 Next Hop Address: : e1000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000009
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
24
SW OCE chain ptr: 0x1186d478 HW OCE chain ptr: 0x895d5660 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV4 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/4 Encap: : 01 00 5e 00 00 00 00 21 d8 d4 a5 14 08 00 Next Hop Address: : e1000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000
To display the complete OCE chain used for forwarding traffic to a particular IPv6 multicast address, use show platform hardware qfp active feature multicast v6mcast ip-address-mgroup ip-address-source vrf vrf-id extension command.
Router#show platform hardware qfp active feature multicast v6mcast FF04::10/128 vrf 503316482 extension Root: 0x11b6c700 Flags: 0x000002 First leaf: 0x11e55bc8 Number of nodes: 1 Number of leaves: 3 RPF i/f: 0x01fff3 Punt limit counter: 200 NS DCS Punt limit: 0x000001 RPF Fast Convergence Flags: 00000000 Secondary RPF interface: 00000000 RPF Fast Convergence Timer: 0 Extended leaf address: 0x8ba18c90 Node: 0x11b6c700 Cumulative Free Space: : 4 Cumulative Weight: : 3 Number of Children: : 3 Hw Addr: : 0x8ba06c60 Node Flags: : 0x000004 Software Child Ptr: : 0x11b6dcb0, 0x11b6e0b0, 0x11e55bc8, 00000000 00000000, 00000000, 00000000 Hardware Child Ptr: : 0x8ba24060, 0x8ba24070, 0x8ba245f0, 00000000 00000000, 00000000, 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11b71af0 HW OCE chain ptr: 0x895ffa40 OCE Type: Adjacency, Number of children: 1 Adj Type: : IPV6 Adjacency Encap Len: : 0 L3 MTU: : 9216 Adj Flags: : 64 Fixup Flags: : 0 Interface Name: Lspvif0 Next Hop Address: : 00000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 0x895ffa20 OCE Type: Label OCE, Number of children: 1 Label flags: : 0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
25
Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 2 Out Backup Labels: : 2 Next HW OCE Ptr: : 0x895ff9f0 OCE Type: Adjacency, Number of children: 1 Adj Type: : MPLS Adjacency Encap Len: : 0 L3 MTU: : 9216 Adj Flags: : 64 Fixup Flags: : 0 Interface Name: Lspvif0 Next Hop Address: : 00000000 00000000 00000000 00000000 Next HW OCE Ptr: : 0x895ff980 OCE Type: REPLICATE OCE, Number of children: 1 Replica_node: : 0x8ba51060 Next HW OCE Ptr: : 0x895ffa60 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 17 Out Backup Labels: : 0 Next HW OCE Ptr: : 0x895ff7b0 OCE Type: Adjacency, Number of children: 0 Adj Type: : MPLS Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 0 Interface Name: GigabitEthernet0/1/0 Encap: : 00 24 14 f4 9d 00 00 21 d8 d4 a5 10 88 47 Next Hop Address: : 0b000002 00000000 00000000 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11b6b800 HW OCE chain ptr: 0x895ff6a0 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV6 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/2 Encap: : 33 33 00 00 00 00 00 21 d8 d4 a5 12 86 dd Next Hop Address: : ff0e0000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11b6ba08 HW OCE chain ptr: 0x895ff6e0 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV6 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
26
Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/4 Encap: : 33 33 00 00 00 00 00 21 d8 d4 a5 14 86 dd Next Hop Address: : ff0e0000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x00000a SW OCE chain ptr: 0x11b6de20 HW OCE chain ptr: 0x895ff770 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV6 Adjacency Encap Len: : 4 L3 MTU: : 1460 Adj Flags: : 2 Fixup Flags: : 2 Interface Name: Tunnel5 Encap: : f8 00 01 47 Next Hop Address: : 00000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 Root: 0x11e4f428 Flags: 00000000 First leaf: 0x11e51b90 Number of nodes: 1 Number of leaves: 3 RPF i/f: 0x0003fd Punt limit counter: 200 NS DCS Punt limit: 0x000001 RPF Fast Convergence Flags: 00000000 Secondary RPF interface: 00000000 RPF Fast Convergence Timer: 0 Extended leaf address: 0x8ba21210 Node: 0x11e4f428 Cumulative Free Space: : 4 Cumulative Weight: : 3 Number of Children: : 3 Hw Addr: : 0x8ba0c560 Node Flags: : 0x000004 Software Child Ptr: : 0x11e424b8, 0x11e332b8, 0x11e51b90, 00000000 Root: 0x11e50f20 Flags: 00000000 First leaf: 0x11e51b90 Number of nodes: 1 Number of leaves: 3 RPF i/f: 0x0003fd Punt limit counter: 200 NS DCS Punt limit: 0x000001 RPF Fast Convergence Flags: 00000000 Secondary RPF interface: 00000000 RPF Fast Convergence Timer: 0 Extended leaf address: 0x8ba212a0 Node: 0x11e50f20 Cumulative Free Space: : 4 Cumulative Weight: : 3 Number of Children: : 3 Hw Addr: : 0x8ba0c560 Node Flags: : 0x000004 Software Child Ptr: : 0x11e424b8, 0x11e56f98, 0x11e51b90, 00000000
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
27
00000000, 00000000, 00000000 Hardware Child Ptr: : 0x8ba247a0, 0x8ba24750, 0x8ba24740, 00000000 00000000, 00000000, 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11b6ba08 HW OCE chain ptr: 0x895ff6e0 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV6 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/4 Encap: : 33 33 00 00 00 00 00 21 d8 d4 a5 14 86 dd Next Hop Address: : ff0e0000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000009 SW OCE chain ptr: 0x11b71af0 HW OCE chain ptr: 0x895ffa40 OCE Type: Adjacency, Number of children: 1 Adj Type: : IPV6 Adjacency Encap Len: : 0 L3 MTU: : 9216 Adj Flags: : 64 Fixup Flags: : 0 Interface Name: Lspvif0 Next Hop Address: : 00000000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 0x895ffa20 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 2 Out Backup Labels: : 2 Next HW OCE Ptr: : 0x895ff9f0 OCE Type: Adjacency, Number of children: 1 Adj Type: : MPLS Adjacency Encap Len: : 0 L3 MTU: : 9216 Adj Flags: : 64 Fixup Flags: : 0 Interface Name: Lspvif0 Next Hop Address: : 00000000 00000000 00000000 00000000 Next HW OCE Ptr: : 0x895ff980 OCE Type: REPLICATE OCE, Number of children: 1 Replica_node: : 0x8ba51060 Next HW OCE Ptr: : 0x895ffa60 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 17 Out Backup Labels: : 0 Next HW OCE Ptr: : 0x895ff7b0
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
28
OCE Type: Adjacency, Number of children: 0 Adj Type: : MPLS Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 0 Interface Name: GigabitEthernet0/1/0 Encap: : 00 24 14 f4 9d 00 00 21 d8 d4 a5 10 88 47 Next Hop Address: : 0b000002 00000000 00000000 00000000 Next HW OCE Ptr: : 00000000 OCE Flags: : 0x000003 SW OCE chain ptr: 0x11b6b800 HW OCE chain ptr: 0x895ff6a0 OCE Type: Adjacency, Number of children: 0 Adj Type: : IPV6 Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 64 Interface Name: GigabitEthernet0/1/2 Encap: : 33 33 00 00 00 00 00 21 d8 d4 a5 12 86 dd Next Hop Address: : ff0e0000 00000000 00000000 00000000 Lisp locator status: : 00000000 Next HW OCE Ptr: : 00000000
To display the complete OCE chain used for handling incoming MPLS packets with the particular label, use show platform hardware qfp active feature cef-mpls prefix mpls mpls-lable exact command.
Router# show platform hardware qfp active feature cef-mpls prefix mpls 17 exact Gtrie Node Type: Leaf Node HW Content: : 0a000000 00000f00 00000000 8bb08a30 QPPB QoS Precedence valid: 0 QoS Precedence: 0 QPPB QoS Group valid: 0 QoS Group: 0 BGPPA Traffic Index valid: 0 BGPPA Traffic Index: 0 TBLF refcount: 2 TBLF application lf handle: 0 CTS src_sgt: 0 CTS dst_sgt: 0 Prefix Length: 20 Prefix: 00 0d 00 Lisp local eid: 0 Lisp remote eid: 0 Lisp locator status bits: 0 Lisp dynamic configured eid: 0 Lisp dynamic discovered eid: 0 OCE Type: EOS OCE, Number of children: 2 Next HW OCE Ptr: : 0x8bb07e10, 0x8bb07e00 OCE Type: REPLICATE OCE, Number of children: 2 Replica_node: : 0x8ca90a20 Next HW OCE Ptr: : 0x8bb07eb0, 0x8bb08840 OCE Type: Label OCE, Number of children: 1 Label flags: : 64
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
29
Num Labels: : 1 Num Bk Labels: : 0 Out Labels: : 1048577 Next HW OCE Ptr: : 0x8bb07e60 OCE Type: Interface OCE, Number of children: 1 Next HW OCE Ptr: : 0x8bb07e40 Interface Name: Lspvif20 OCE Type: Lookup OCE, Number of children: 0 Lookup flags: : 1 Table Type: : 0 Lookup table ID: : 0 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 88 Out Backup Labels: : 0 Next HW OCE Ptr: : 0x8bb06ca0 OCE Type: Adjacency, Number of children: 0 Adj Type: : MPLS Adjacency Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 0 Interface Name: GigabitEthernet0/1/0 Encap: : 00 0e 39 88 70 19 00 21 d8 60 c0 10 88 47 Next Hop Address: : 0f000001 00000000 00000000 00000000 Next HW OCE Ptr: : 00000000 OCE Type: REPLICATE OCE, Number of children: 2 Replica_node: : 0x8ca90a00 Next HW OCE Ptr: : 0x8bb07e70, 0x8bb08840 OCE Type: Label OCE, Number of children: 1 Label flags: : 64 Num Labels: : 1 Num Bk Labels: : 0 Out Labels: : 1048577 Next HW OCE Ptr: : 0x8bb07e50 OCE Type: Interface OCE, Number of children: 1 Next HW OCE Ptr: : 0x8bb001f0 Interface Name: Lspvif20 OCE Type: Lookup OCE, Number of children: 0 Lookup flags: : 0 Table Type: : 1 Lookup table ID: : 2 OCE Type: Label OCE, Number of children: 1 Label flags: : 0 Num Labels: : 1 Num Bk Labels: : 1 Out Labels: : 88 Out Backup Labels: : 0 Next HW OCE Ptr: : 0x8bb06ca0 OCE Type: Adjacency, Number of children: 0 Adj Type: : MPLS Adjacency
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
30
Encap Len: : 14 L3 MTU: : 1500 Adj Flags: : 0 Fixup Flags: : 0 Interface Name: GigabitEthernet0/1/0 Encap: : 00 0e 39 88 70 19 00 21 d8 60 c0 10 88 47 Next Hop Address: : 0f000001 00000000 00000000 00000000 Next HW OCE Ptr: : 00000000
MLDP MVPN Extranet SSC MLDP MVPN Extranet RSC MLDP MVPN Intranet
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
31
ip vrf forwarding red2 ip address 101.2.0.2 255.255.255.255 ip pim sparse-mode ! interface Loopback103 ip vrf forwarding red3 ip address 101.3.0.2 255.255.255.255 ip pim sparse-mode interface GigabitEthernet1/22.2 encapsulation dot1Q 2 ip vrf forwarding red2 ip address 12.2.0.1 255.255.0.0 ip pim sparse-mode ! interface TenGigabitEthernet8/1 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp router ospf 1 router-id 1.1.1.1 network 1.1.1.1 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
32
neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ip pim vrf red2 ssm default ip pim vrf red3 ssm default ip mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2
Configuration on PE Router:
interface Loopback1 ip address 4.4.4.4 255.255.255.255 interface GigabitEthernet2/10 ip address 20.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp interface GigabitEthernet2/20 ip address 30.1.1.2 255.255.255.0 ip ospf 1 area 0 mpls ip mpls label protocol ldp interface TenGigabitEthernet4/0/0 ip address 10.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp router ospf 1 router-id 4.4.4.4 network 4.4.4.4 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 2.2.2.2 remote-as 100 neighbor 3.3.3.3 remote-as 100 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate no auto-summary exit-address-family
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
33
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
34
address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family
both both
both
both
! ip pim vrf red3 ssm default ip mroute vrf red3 12.2.0.0 255.255.0.0 101.3.0.2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
35
! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! ip pim vrf red3 ssm default ip mroute vrf red3 12.2.0.0 255.255.0.0 101.3.0.2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
36
ip address 1.1.1.1 255.255.255.255 ip pim sparse-mode ! interface Loopback102 ip vrf forwarding red2 ip address 101.2.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet1/22.2 encapsulation dot1Q 2 ip vrf forwarding red2 ip address 12.2.0.1 255.255.0.0 ip pim sparse-mode ! interface TenGigabitEthernet8/1 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp ! router ospf 1 router-id 1.1.1.1 network 1.1.1.1 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
37
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
38
vpn id 10:3 mdt default mpls MLDP 4.4.4.4 mdt data mpls MLDP 100 mdt data threshold 20 route-target export 10:3 route-target import 10:3 ! ip multicast-routing ip multicast-routing vrf red3 ip multicast-routing vrf red2 ! interface Loopback1 ip address 2.2.2.2 255.255.255.255 ip pim sparse-mode ! interface Loopback102 ip vrf forwarding red2 ip address 102.2.0.2 255.255.255.255 ip pim sparse-mode ! interface Loopback103 ip vrf forwarding red3 ip address 102.3.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet4/0/0 ip address 20.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! interface GigabitEthernet4/0/1.3 encapsulation dot1Q 3 ip vrf forwarding red3 ip address 22.2.0.1 255.255.0.0 ip pim sparse-mode ! router ospf 1 router-id 2.2.2.2 network 2.2.2.2 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
39
exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family
both both
both
both
both
both
! ip pim vrf red3 ssm default ip pim vrf red2 ssm default ip mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
40
interface Loopback102 ip vrf forwarding red2 ip address 103.2.0.2 255.255.255.255 ip pim sparse-mode ! interface Loopback103 ip vrf forwarding red3 ip address 103.3.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet3/2/0.3 encapsulation dot1Q 3 ip vrf forwarding red3 ip address 32.2.0.1 255.255.0.0 ip pim sparse-mode ip igmp version 3 ! interface GigabitEthernet3/2/1 ip address 30.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! router ospf 1 router-id 3.3.3.3 network 3.3.3.3 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
41
neighbor 1.1.1.1 send-community neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community exit-address-family
both
both
both
both
! ip pim vrf red3 ssm default ip pim vrf red2 ssm default ip mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
42
router bgp 100 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! ip pim vrf red2 ssm default
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
43
ip address 10.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp mls qos trust dscp ! router ospf 1 router-id 4.4.4.4 network 4.4.4.4 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 2.2.2.2 remote-as 100 neighbor 3.3.3.3 remote-as 100 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate no auto-summary exit-address-family !
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
44
router ospf 1 router-id 2.2.2.2 network 2.2.2.2 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! ip pim vrf red2 ssm default !
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
45
ip pim sparse-mode ! interface Loopback102 ip vrf forwarding red2 ip address 103.2.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet3/2/0.2 encapsulation dot1Q 2 ip vrf forwarding red2 ip address 32.2.0.1 255.255.0.0 ip pim sparse-mode ip igmp version 3 ! interface GigabitEthernet3/2/1 ip address 30.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! router ospf 1 router-id 3.3.3.3 network 3.3.3.3 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
46
neighbor 2.2.2.2 send-community both exit-address-family ! ip pim vrf red2 ssm default !
MLDP MVPN Extranet SSC MLDP MVPN Extranet RSC MLDP MVPN Intranet
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
47
! interface TenGigabitEthernet8/1 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp router ospf 1 router-id 1.1.1.1 network 1.1.1.1 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
48
ip ip ip ip
pim vrf red2 rp-address 11.11.11.11 pim vrf red3 rp-address 11.11.11.11 mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2 mroute vrf red3 11.11.11.11 255.255.0.0 fallback-lookup vrf red2
Configuration on P Router
interface Loopback1 ip address 4.4.4.4 255.255.255.255 interface GigabitEthernet2/10 ip address 20.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp interface GigabitEthernet2/20 ip address 30.1.1.2 255.255.255.0 ip ospf 1 area 0 mpls ip mpls label protocol ldp interface TenGigabitEthernet4/0/0 ip address 10.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp router ospf 1 router-id 4.4.4.4 network 4.4.4.4 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 2.2.2.2 remote-as 100 neighbor 3.3.3.3 remote-as 100 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate no auto-summary exit-address-family
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
49
ip address 2.2.2.2 255.255.255.255 ip pim sparse-mode ! interface Loopback103 ip vrf forwarding red3 ip address 102.3.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet4/0/0 ip address 20.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! interface GigabitEthernet4/0/1.3 encapsulation dot1Q 3 ip vrf forwarding red3 ip address 22.2.0.1 255.255.0.0 ip pim sparse-mode ! router ospf 1 router-id 2.2.2.2 network 2.2.2.2 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
50
neighbor 3.3.3.3 send-community both exit-address-family ! ip pim vrf red3 rp-address 11.11.11.11 ip mroute vrf red3 12.2.0.0 255.255.0.0 101.3.0.2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
51
address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community exit-address-family
both both
both both
both
both
! ip pim vrf red3 rp-address 11.11.11.11 ip mroute vrf red3 12.2.0.0 255.255.0.0 101.3.0.2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
52
mpls ip mpls label protocol ldp ! router ospf 1 router-id 1.1.1.1 network 1.1.1.1 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! ip pim vrf red2 rp-address 11.11.11.11
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
53
interface GigabitEthernet2/20 ip address 30.1.1.2 255.255.255.0 ip ospf 1 area 0 mpls ip mpls label protocol ldp ! interface TenGigabitEthernet4/0/0 ip address 10.1.1.2 255.255.255.0 ip ospf 1 area 0 load-interval 30 mpls ip mpls label protocol ldp mls qos trust dscp ! router ospf 1 router-id 4.4.4.4 network 4.4.4.4 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 2.2.2.2 remote-as 100 neighbor 3.3.3.3 remote-as 100 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate no auto-summary exit-address-family !
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
54
ip pim sparse-mode ! interface Loopback103 ip vrf forwarding red3 ip address 102.3.0.2 255.255.255.255 ip pim sparse-mode ! interface GigabitEthernet4/0/0 ip address 20.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! interface GigabitEthernet4/0/1.3 encapsulation dot1Q 3 ip vrf forwarding red3 ip address 22.2.0.1 255.255.0.0 ip pim sparse-mode ! router ospf 1 router-id 2.2.2.2 network 2.2.2.2 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 3.3.3.3 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
55
exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community both exit-address-family ! ip ip ip ip pim vrf red2 rp-address 11.11.11.11 pim vrf red3 rp-address 11.11.11.11 mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2 mroute vrf red3 11.11.11.11 255.255.255.255 fallback-lookup vrf red2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
56
! interface GigabitEthernet3/2/1 ip address 30.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! router ospf 1 router-id 3.3.3.3 network 3.3.3.3 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red3 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
57
! ip ip ip ip
pim vrf red2 rp-address 11.11.11.11 pim vrf red3 rp-address 11.11.11.11 mroute vrf red3 12.2.0.0 255.255.0.0 fallback-lookup vrf red2 mroute vrf red3 11.11.11.11 255.255.255.255 fallback-lookup vrf red2
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
58
! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 mdt neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family
both both
both both
both
both
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
59
! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 3.3.3.3 activate no auto-summary exit-address-family !
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
60
neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community neighbor 3.3.3.3 remote-as 100 neighbor 3.3.3.3 activate neighbor 3.3.3.3 send-community exit-address-family
both both
both both
both
both
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
61
ip address 30.1.1.1 255.255.255.0 ip ospf 1 area 0 load-interval 30 negotiation auto mpls ip mpls label protocol ldp ! router ospf 1 router-id 3.3.3.3 network 3.3.3.3 0.0.0.0 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 update-source Loopback1 neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 update-source Loopback1 neighbor 4.4.4.4 remote-as 100 neighbor 4.4.4.4 update-source Loopback1 ! address-family ipv4 neighbor 1.1.1.1 activate neighbor 2.2.2.2 activate neighbor 4.4.4.4 activate no auto-summary exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 mdt neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! address-family ipv4 vrf red2 redistribute static redistribute connected neighbor 1.1.1.1 remote-as 100 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community both neighbor 2.2.2.2 remote-as 100 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community both exit-address-family ! ip pim vrf red2 rp-address 11.11.11.11 !
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
62
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
63
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
64
Tracing Overview, page 1 How Tracing Works, page 1 Tracing Levels, page 2 Viewing a Tracing Level, page 3 Setting a Tracing Level, page 4 Viewing the Content of the Trace Buffer, page 5
Tracing Overview
Tracing is a function that logs internal events. Trace files are automatically created and saved to the tracelogs directory on the harddisk: file system on all Cisco ASR 1000 Series Routers except the Cisco ASR 1002 Router, which stores tracing files in bootflash:. Trace files are used to store tracing data. The contents of trace files are useful for the following purposes:
TroubleshootingIf a Cisco ASR 1000 Series Router is having an issue, the trace file output may provide information that is useful for locating and solving the problem. Trace files can almost always be accessed through diagnostic mode even if other system issues are occurring. DebuggingThe trace file outputs can help users get a more detailed view of system actions and operations.
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Trace files can be copied to other destinations using most file transfer functions (such as FTP, TFTP, and so on) and opened using a plaintext editor. Tracing cannot be disabled on the Cisco ASR 1000 Series Router. Trace levels, however, which set the message types that generate trace output, are user-configurable and can be set using the platform trace commands. If a user wants to modify the trace level to increase or decrease the amount of trace message output, the user should set a new tracing level using the platform trace commands. Trace levels can be set by process using the all-modules keyword within the platform trace commands, or by module within a process. See the platform trace command reference for more information on this command, and the Tracing Levels section on page 2 of this document for additional information on tracing levels.
Tracing Levels
Tracing levels determine how much information about a module should be stored in the trace buffer or file. shows all of the trace levels that are available and provides descriptions of what types of messages are displayed with each tracing level.
Table 1 Tracing Levels and Descriptions
Trace Level Emergency Alert Critical Error Warning Notice Informational Debug Verbose Noise
Level Number 0 1 2 3 4 5 6 7 8 -
Description The message is regarding an issue that makes the system unusable. The message is regarding an action that must be taken immediately. The message is regarding a critical condition. This is the default setting for every module on the Cisco ASR 1000 Series Routers. The message is regarding a system error. The message is regarding a system warning The message is regarding a significant issue, but the router is still working normally. The message is useful for informational purposes only. The message provides debug-level output. All possible tracing messages are sent. All possible trace messages for the module are logged. The noise level is always equal to the highest possible tracing level. Even if a future enhancement to tracing introduces a higher tracing level, the noise level will become equal to the level of that new enhancement.
Trace level settings are leveled, meaning that every setting will contain all messages from the lower setting plus the messages from its own setting. For instance, setting the trace level to 3(error) ensures that the trace file will contain all output for the 0 (emergencies), 1 (alerts), 2 (critical), and 3 (error) settings. Setting the trace level to 4 (warning) will ensure that all trace output for the specific module will be included in that trace file. The default tracing level for every module on the Cisco ASR 1000 Series Router is notice.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
All trace levels are not user-configurable. Specifically, the alert, critical, and notice tracing levels cannot be set by users. If you wish to trace these messages, set the trace level to a higher level that will collect these messages. When setting trace levels, it is also important to remember that the setting is not done in a configuration mode, so trace level settings are returned to their defaults after every router reload.
Caution
Setting tracing of a module to the debug level or higher can have a negative performance impact. Setting tracing to this level or higher should be done with discretion.
Caution
Setting a large number of modules to high tracing levels can severely degrade performance. If a high level of tracing is needed in a specific context, it is almost always preferable to set a single module on a higher tracing level rather than setting multiple modules to high tracing levels.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
mlp mqipc nat nbar netflow om peer qos route-map sbc services sw_wdog tdl_acl_config_type tdl_acl_db_type tdl_cdlcore_message tdl_cef_config_common_type tdl_cef_config_type tdl_dpidb_config_type tdl_fman_rp_comm_type tdl_fman_rp_message tdl_fw_config_type tdl_hapi_tdl_type tdl_icmp_type tdl_ip_options_type tdl_ipc_ack_type tdl_ipsec_db_type tdl_mcp_comm_type tdl_mlp_config_type tdl_mlp_db_type tdl_om_type tdl_ui_message tdl_ui_type tdl_urpf_config_type tdllib trans_avl uihandler uipeer uistatus urpf vista wccp
Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice Notice
In the following example, the trace level for the forwarding processor module in the Forwarding Manager of the ESP processor in slot R0 is set to the informational tracing level (max):
Router(config)# platform trace boottime slot R0 bay 1 process forwarding-manager forwarding-manager level max
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
See the platform trace boottime process forwarding-manager moduleinterfaces and platform trace runtime process forwarding-manager moduleinterfaces command reference for additional information about the options for this command.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Web User Interface Overview, page 1 Configuring the Router for Web User Interface Access, page 5 Authentication and the Web User Interface, page 7 Domain Name System and the Web User Interface, page 7 Clocks and the Web User Interface, page 7 Accessing the Web User Interface, page 8 Using Auto Refresh, page 9 Web User Interface Tips and Tricks, page 10
Web User Interface General Overview, page 1 Legacy Web User Interface Overview, page 2 Graphics-Based Web User Interface Overview, page 3 Persistent Web User Interface Transport Maps Overview, page 4
Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Configuring and Accessing the Web User Interface Web User Interface Overview
The Cisco ASR 1000 Series Routers can be accessed using a web user interface. This web user interface allows users to monitor router performance using an easy-to-read graphical interface. Most aspects of a Cisco ASR 1000 Series Router can be monitored using the web user interface. The web user interface has the following features:
An interface that presents information in an easy-to-read graphical format. An interface that allows users to monitor most software processes, including processes related to the IOS and nonIOS subpackages within the Cisco IOS XE consolidated package. An interface that allows users to monitor most hardware components, including all RPs, ESPs, SIPs, and SPAs installed in the router. Access to the legacy web user interface in addition to the enhanced web user interface. The ability to gather the output of show commands from the web user interface.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Web User Interface Overview
See Figure 2 for an example of the legacy web user interface home page.
Figure 2 Legacy Web User Interface Home Page
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Web User Interface Overview
See Figure 3 for an example of the graphics-based web user interface home page.
Figure 3 Graphics-Based Web User Interface Home Page
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Configuring the Router for Web User Interface Access
The persistent web user interface transport map configuration must be performed in addition to the legacy web user interface configuration, which is configured using the ip http command set. The ip http command settings define which ports are used by HTTP or HTTPS for both the legacy and graphics-based web user interface. For information on configuring the entire graphics-based web user interface, including the configuration of persistent web user interface transport maps, see the Configuring the Router for Web User Interface Access section on page 5.
Note
The web user interface will not work if the Management Ethernet interface has not been configured or is not working; specifically, the default route must be specified in the Management Ethernet VRF before the web user interface can be configured. See the Using the Management Ethernet Interface chapter for information on configuring the Management Ethernet interface on your router. See the Setting a Default Route in the Management Ethernet Interface VRF section on page 4 chapter for information on configuring a default route in the Management Ethernet interface on your router. To enable the entire web user interface, perform the following tasks:
Step 1
(Optional) Ensure the clock setting on your router is accurate by entering the show clock command.
Router# show clock *13:56:59.257 DST Mon May 5 2008
If the router time is not properly set, use the clock set and clock timezone commands for setting the router clock.
Note
The Clocks and the Web User Interface section on page 7 provides additional information on how clock settings on both the router and the web-browser can impact the web user interface. Connect to your router and enter the configure terminal command to enter global configuration mode. Set the HTTP server authentication method to local by entering the ip http authentication local command. Enable the legacy web user interface by entering one of the following global configuration commands:
ip http serverEnables HTTP on port 80, which is the default HTTP port. ip http port port-numberEnables HTTP on the nondefault user-specified port. ip http secure-serverEnables HTTPS on port 443, the default HTTPS port. ip http secure-port port-numberEnables HTTPS on the nondefault user-specified port.
The legacy web user interface becomes available at this point of the procedure. Users attempting to access the web user interface after this step is completed will see the legacy web user interface only.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Configuring the Router for Web User Interface Access
To enable the graphics-based web user interface, proceed to Step 5 and complete the remaining steps in this procedure.
Step 5 Step 6
Create and name a persistent web user interface transport map by entering the transport-map type persistent webui transport-map-name command. Enable HTTP, HTTPS, or both by entering the following commands in transport map configuration mode:
Port numbers cannot be set within the transport map. The port numbers defined in Step 4 are also used with these settings in the persistent web user interface transport map.
Step 7 Step 8
(Optional) Enter the show transport-map name transport-map-name privileged EXEC command to verify that your transport map is properly configured. Enable the transport map by entering the transport type persistent webui input transport-map-name global configuration command.
Examples
In the following example, the HTTP server authentication method is set to local:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip http authentication local Router(config)# exit
In the following example, the web user interface using the default HTTP port is enabled:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip http server Router(config)# transport-map type persistent webui http-webui Router(config-tmap)# server Router(config-tmap)# exit Router(config)# exit Router# show transport-map name http-webui Transport Map: Name: http-webui Type: Persistent Webui Transport Webui: Server: enabled Secure Server: disabled Router# configure terminal Router(config)# transport type persistent webui input http-webui *Apr 22 02:43:55.798: %UICFGEXP-6-SERVER_NOTIFIED_START: R0/0: psd: notified to start
In the following example, the web user interface using the default HTTPs port is enabled:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip http secure-server Router(config)# transport-map type persistent webui https-webui Router(config-tmap)# secure-server Router(config-tmap)# exit Router(config)# transport type persistent webui input https-webui
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Authentication and the Web User Interface
In the following example, the web user interface using the default HTTP and HTTPS ports is enabled:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip http server Router(config)# ip http secure-server Router(config)# transport-map type persistent webui http-https-webui Router(config-tmap)# server Router(config-tmap)# secure-server Router(config-tmap)# exit Router(config)# transport type persistent webui input http-https-webui *Apr 22 02:47:22.981: %UICFGEXP-6-SERVER_NOTIFIED_START: R0/0: psd: Server wui has been notified to start
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Accessing the Web User Interface
Your access is being denied for one of the following reasons: . Your previous session has timed-out, or . You have been logged out from elsewhere, or . You have not yet logged in, or . The resource requires a higher privilege level login.
If you see this message and fixing the other possible causes of the issue still does not make the web user interface accessible, check both the router clock and the PC clock to ensure both clocks reflect the accurate day and time and then retry your connection to the web user interface. Also note that if one clock changes at daylight savings time while another clock does not, clock-related issues can occur.
Open your web browser. The web user interface supports the following web browsers:
Step 2
Enter the address of the router in the address field of the web browser. The format for the address of the router in the address field is http://<routername or management-ethernet-ip-address>:[http-port] or https://<routername or management-ethernet-ip-address>:[https-port], and the addresses that are acceptable depend upon your web browser user interface configurations and whether your router is participating in DNS. Following are some examples of acceptable address field web browser entries:
HTTP Using Default Port Example http://172.16.5.1 HTTPS Using Default Port Example https://172.16.5.1 HTTP Using NonDefault Port Example http://172.16.5.1:94 HTTPS Using NonDefault Port Example https://172.16.5.1:530/ HTTP Using Default Port Participating in DNS Example http://router1 HTTPS Using Default Port Participating in DNS Example https://router1 HTTP Using NonDefault Port Participating in DNS Example http://router1:94 HTTPS Using NonDefault Port Participating in DNS Example https://router1:530/
Step 3 Step 4
If prompted, enter your username and password. The username and password combination required to enter the web user interface is the same combination required to access the router. The graphics-based web user interface similar to Figure 3 in the Graphics-Based Web User Interface Overview section on page 3 should appear in your web browser.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Using Auto Refresh
For additional information on the commands and the options available with each command, see the Cisco IOS Configuration Fundamentals Command Reference Guide located at: http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_book.html.
Check the Refresh every check box on the graphical web user interface home page. A check mark appears in the check box (See Figure 4).
Figure 4 Checking Auto Refresh Check Box
Step 2 Step 3
Set the frequency of the auto-refresh interval using the drop-down menu. Click the Start button to the right of the drop-down menu. After hitting this button, the Start button becomes the Stop button and a countdown timer placed to the right of the Stop button begins to increment (See Figure 5).
Figure 5 Auto Refresh Counter Example
The web user interface screen refreshes every time this counter reaches 0 seconds. If you would like to stop the auto-refresh update, click the Stop button to return to the default setting of no auto-refresh update.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Configuring and Accessing the Web User Interface Web User Interface Tips and Tricks
If you know a Cisco IOS command-line interface command to gather information that you are unable to gather using the web user interface, you can click IOS Web UI followed by Monitor the Router to enter commands. If you know a diagnostic mode command to gather information that you are unable to gather using the web user interface, you can click WebCLI to enter show commands. The WebCLI command line has a context-sensitive help feature that shows the options available in a certain keyword sequence using a drop-down menu. Figure 6 shows an example of this drop-down menu context-sensitive help feature.
Web CLI Drop-Down Menu
Figure 6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
10
A P P E N D I X
Unsupported Commands
The Cisco ASR 1000 Series Routers contain a series of commands with the platform keyword that either produce no output or produce output that is not useful for customer purposes. Although some commands with the platform keyword produce output that is useful for customer purposes, and are therefore documented in the Cisco IOS XE command references, the vast majority of these commands are not useful for customer purposes and are therefore considered unsupported. Because these commands are considered unsupported, you will not find any further Cisco documentation for any of these commands. Following is the list of unsupported commands for the Cisco ASR 1000 Series Routers:
clear platform hardware cpp clear platform software access-list clear platform software adjacency clear platform software cce clear platform software cef clear platform software cman clear platform software dpidb clear platform software ess clear platform software icmp clear platform software infrastructure clear platform software inspect clear platform software mlp clear platform software mpls clear platform software multicast clear platform software nat clear platform software nbar clear platform software netflow clear platform software pam clear platform software qos clear platform software route-map clear platform software shell
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
A-1
Appendix A
Unsupported Commands
clear platform software wccp clear platform software zone clear platform software zone-pair debug platform all debug platform hardware cpp debug platform software acl debug platform software adjacency debug platform software cce debug platform software cef debug platform software cman debug platform software configuration debug platform software dpidb debug platform software entity debug platform software ess debug platform software FPM debug platform software icmp debug platform software infrastructure debug platform software inspect debug platform software iphc debug platform software ipsec debug platform software issu debug platform software kernel debug platform software liin debug platform software marmot debug platform software mlp debug platform software mpls debug platform software multicast debug platform software nat debug platform software nbar debug platform software netflow debug platform software pam debug platform software qos debug platform software route-map debug platform software shell debug platform software urpf debug platform software vty debug platform software wccp debug platform software zone
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
A-2
OL-16506-13
Appendix A
Unsupported Commands
set platform software trace show crypto engine show platform hardware cpp (all commands) show platform software access-list show platform software adjacency show platform software bound-uds show platform software cce statistics show platform software cef counters show platform software cman statistics show platform software common-classification show platform software debug show platform software diagnostic show platform software dpidb show platform software erspan show platform software ess show platform software firewall show platform software flow-control identifier show platform software fpm show platform software icmp show platform software icmp6 show platform software infrastructure show platform software inspect statistics show platform software interface show platform software ip show platform software ipc show platform software iphc show platform software ipsec show platform software ipv6 show platform software loadinfo show platform software mlist show platform software mlp show platform software mlppp show platform software module show platform software mpls show platform software multicast show platform software nat show platform software nbar show platform software netflow
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
A-3
Appendix A
Unsupported Commands
show platform software object-manager show platform software os-interface show platform software pam show platform software peer show platform software punt show platform software push-counter show platform software qos show platform software sbc tables show platform software shell show platform software slot show platform software spi4 show platform software urpf show platform software vlans show platform software vty show platform software wccp show platform software zone statistics test platform hardware eobc test platform hardware port test platform hardware slot test platform hardware subslot test platform software cef test platform software chassis test platform software debug test platform software forwarding-manager test platform software infrastructure test platform software inject test platform software process test platform software shell test platform software tdl test platform software trace
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
A-4
OL-16506-13
A P P E N D I X
Configuration Examples
This appendix is designed to provide examples of how some common networking tasks can be accomplished on the Cisco ASR 1000 Series Routers. The examples in this appendix are provided for illustrative purposes only; little or no context is given with these examples. See the other chapters in this book (in particular Chapter 3, Consolidated Packages and SubPackages Management), for more detailed explanations of the examples in this section. When reading this section, also be aware that networking configurations are complex and can be configured many ways. The examples in this section simply show one method of accomplishing a configuration. This appendix contains the following examples:
Configuring the Router to Boot the Consolidated Package on the TFTP Server, page B-1 Copying the Consolidated Package from the TFTP Server to the Router, page B-5 Configuring the Router to Boot Using the Consolidated Package Stored on the Router, page B-6 Extracting the SubPackages from a Consolidated Package into the Same File System, page B-7 Extracting the SubPackages from a Consolidated Package into a Different File System, page B-9 Configuring the Router to Boot Using the SubPackages, page B-10 Backing Up Configuration Files, page B-14 Enabling a Second IOS Process on a Single RP Using SSO, page B-15 ISSUConsolidated Package Upgrade, page B-19
Configuring the Router to Boot the Consolidated Package on the TFTP Server
The following example shows how to configure the router to boot the consolidated package on the TFTP server:
Router(config)# boot system tftp://172.17.16.81/auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bi n Router(config)#config-reg 0x2102 Router(config)# exit *May 29 21:51:11.963: %SYS-5-CONFIG_I: Configured from console by user on console Router# show run | include boot boot-start-marker
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-1
Appendix B Configuring the Router to Boot the Consolidated Package on the TFTP Server
Configuration Examples
boot system tftp://172.17.16.81/auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bi n boot-end-marker Router# copy run start Destination filename [startup-config]? Building configuration... [OK] Router# reload Proceed with reload? [confirm] *May 29 21:52:01.500: %SYS-5-RELOAD: Reload requested by user on console. Reload Reason: Reload command.
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc.
Current image running: Boot ROM0 Last reset cause: LocalSoft ASR1000-RP1 platform with 4194303 Kbytes of main memory
IP_ADDRESS: 172.17.52.155 IP_SUBNET_MASK: 255.255.255.0 DEFAULT_GATEWAY: 172.17.52.1 TFTP_SERVER: 172.17.16.81 TFTP_FILE: auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Using midplane macaddr TFTP_MACADDR: 00:1a:30:46:e3:ff TFTP_VERBOSE: Progress TFTP_RETRY_COUNT: 18 TFTP_TIMEOUT: 7200 TFTP_CHECKSUM: Yes ETHER_PORT: 3 ETHER_SPEED_MODE: Auto Detect link up 100Mbps/HD Receiving auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin from 172.17.16.81 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!. !!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! File reception completed. Boot image size = 208904396 (0xc73a0cc) bytes Using midplane macaddr Package header rev 0 structure detected
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-2
OL-16506-13
Appendix B
Configuration Examples Configuring the Router to Boot the Consolidated Package on the TFTP Server
Calculating SHA-1 hash...done validate_package: SHA-1 hash: calculated fb456e80:4ba2fa07:8556d27c:ea643e4f:512236df expected fb456e80:4ba2fa07:8556d27c:ea643e4f:512236df Image validated
PPC/IOS XE loader version: 0.0.3 loaded at: 00800000 0CF3C004 zimage at: 00807673 009B92D6 initrd at: 009BA000 01041CC9 isord at: 01042000 0CF39800 avail ram: 00400000 00800000 Kernel load: Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size: 001B1C63...done. Now booting the IOS XE kernel %IOSXEBOOT-4-BOOT_SRC: (rp/0): Non-HD Boot %IOSXEBOOT-4-BOOT_PARAMETER: (rp/0): Booting with custom BOOT_PARAM setting Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre Image text-base: 0x10064AF0, data-base: 0x137E0958
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-3
Appendix B Configuring the Router to Boot the Consolidated Package on the TFTP Server
Configuration Examples
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772131K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Duplex is configured.Remove duplex configuration before enabling auto-negotiation <output removed for brevity> User Access Verification Username: user Password: Router>en Password: Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
ROM: IOS-XE ROMMON Router uptime is 2 minutes Uptime for this control processor is 4 minutes System returned to ROM by reload at 14:52:01 DST Thu May 29 2008 System image file is "tftp://172.17.16.81/auto/tftp-users/user/asr1000rp1-adve" Last reload reason: Reload command
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-4
OL-16506-13
Appendix B
Configuration Examples Copying the Consolidated Package from the TFTP Server to the Router
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772131K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Configuration register is 0x2102
Copying the Consolidated Package from the TFTP Server to the Router
The following example shows how to copy the consolidated package from the TFTP server to the router:
Router# dir bootflash: Directory of bootflash:/ 11 86401 14401 28801 43201 13 drwx drwx drwx drwx drwx -rw16384 4096 4096 4096 4096 45977 Dec 4 Dec 4 Dec 4 Mar 18 Dec 4 Apr 9 2007 2007 2007 2008 2007 2008 04:32:46 06:06:24 06:06:36 17:31:17 04:34:45 16:48:46 -08:00 -08:00 -08:00 -07:00 -08:00 -07:00 lost+found .ssh .rollback_timer .prst_sync .installer target_support_output.tgz.tgz
928862208 bytes total (712273920 bytes free) Router# copy tftp bootflash: Address or name of remote host []? 172.17.16.81 Source filename []? /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Destination filename [asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin]? Accessing tftp://172.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.b in... Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!! [OK - 208904396 bytes] 208904396 bytes copied in 330.453 secs (632176 bytes/sec) Router# dir bootflash: Directory of bootflash:/
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-5
Appendix B Configuring the Router to Boot Using the Consolidated Package Stored on the Router
Configuration Examples
11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 928862208 bytes total (503156736 bytes free)
target_support_output.tgz.tgz
Configuring the Router to Boot Using the Consolidated Package Stored on the Router
The following example shows hot to configure the router to boot using the consolidated package stored on the router:
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 928862208 bytes total (503156736 bytes free) Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#boot system bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Router(config)#config-reg 0x2102 Router(config)#exit Router#show run | include boot boot-start-marker boot system bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin boot-end-marker Router# copy run start Destination filename [startup-config]? Building configuration... [OK] Router# reload <output removed for brevity> User Access Verification Username: user Password: Router>en Password: Router#show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. lost+found .ssh .rollback_timer .prst_sync .installer
target_support_output.tgz.tgz
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-6
OL-16506-13
Appendix B
Configuration Examples Extracting the SubPackages from a Consolidated Package into the Same File System
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
ROM: IOS-XE ROMMON Router uptime is 3 minutes Uptime for this control processor is 5 minutes System returned to ROM by reload at 16:20:55 DST Wed May 28 2008 System image file is "bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin" Last reload reason: Reload command
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772131K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Configuration register is 0x2102
Extracting the SubPackages from a Consolidated Package into the Same File System
The following example shows how to extract the subpackages from a consolidated package into the same file system:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-7
Appendix B Extracting the SubPackages from a Consolidated Package into the Same File System
Configuration Examples
The asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin consolidated package file is in bootflash, but no sub-packages are in the directory.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw45977 Apr 9 2008 16:48:46 -07:00 928862208 bytes total (503156736 bytes free) Router# request platform software package expand file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. lost+found .ssh .rollback_timer .prst_sync .installer
target_support_output.tgz.tgz
After entering the request platform software package expand file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin command, noting that the to option is not used, the sub-packages are extracted from the consolidated package into bootflash:.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw208904396 May 9 2008 14:36:31 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 57611 -rw47071436 May 22 2008 11:26:23 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw5740 May 22 2008 11:26:22 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57612 -rw20334796 May 22 2008 11:26:24 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57613 -rw22294732 May 22 2008 11:26:24 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg 57614 -rw21946572 May 22 2008 11:26:25 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57615 -rw48099532 May 22 2008 11:26:26 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57616 -rw34324684 May 22 2008 11:26:27 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg 57617 -rw22124748 May 22 2008 11:26:28 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 57603 -rw6256 May 22 2008 11:26:28 -07:00 packages.conf 13 -rw45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (286662656 bytes free)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-8
OL-16506-13
Appendix B
Configuration Examples Extracting the SubPackages from a Consolidated Package into a Different File System
Extracting the SubPackages from a Consolidated Package into a Different File System
The following example shows how to extract the subpackages from a consolidated package into a different file system: The asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin consolidated package file is in usb0:
Router# dir usb0: Directory of usb0:/ 1240 -rwx 208904396 May 27 2008 14:10:20 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 255497216 bytes total (40190464 bytes free)
945377280 bytes total (695246848 bytes free) Router# request platform software package expand file usb0:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin to bootflash: Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package.
After the request platform software package expand file usb0:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin to bootflash: command is entered, the sub-packages are now in the bootflash: directory.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 13 2004 03:45:47 -08:00 lost+found 87937 drwx 4096 Dec 13 2004 03:46:45 -08:00 .rollback_timer 14657 drwx 4096 Dec 13 2004 03:47:17 -08:00 .installer 29313 drwx 4096 Dec 13 2004 03:53:00 -08:00 .ssh 12 -rw33554432 Dec 13 2004 03:53:49 -08:00 nvram_00100 43979 -rw47071436 May 27 2008 14:25:01 -07:00 asr1000rp1-espbase.02.01.00.122-33.XNA.pkg 58625 drwx 4096 May 7 2008 17:27:51 -07:00 .prst_sync 43970 -rw5740 May 27 2008 14:25:00 -07:00 asr1000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 43980 -rw20334796 May 27 2008 14:25:01 -07:00 asr1000rp1-rpaccess.02.01.00.122-33.XNA.pkg 43981 -rw22294732 May 27 2008 14:25:02 -07:00 asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-9
Configuration Examples
43982 -rw21946572 May 27 2008 14:25:03 -07:00 asr1000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 43983 -rw48099532 May 27 2008 14:25:04 -07:00 asr1000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 43984 -rw34324684 May 27 2008 14:25:05 -07:00 asr1000rp1-sipbase.02.01.00.122-33.XNA.pkg 43985 -rw22124748 May 27 2008 14:25:05 -07:00 asr1000rp1-sipspa.02.01.00.122-33.XNA.pkg 43971 -rw6256 May 27 2008 14:25:05 -07:00 packages.conf 945377280 bytes total (478752768 bytes free)
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-10
OL-16506-13
Appendix B
boot-start-marker boot system bootflash:packages.conf boot-end-marker Router# copy run start Destination filename [startup-config]? Building configuration... [OK] Router# reload Proceed with reload? [confirm] *May 29 22:51:54.194: %SYS-5-RELOAD: Reload requested by user on console. Reload Reason: Reload command.
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc.
Current image running: Boot ROM0 Last reset cause: LocalSoft ASR1000-RP1 platform with 4194303 Kbytes of main memory Located packages.conf Image size 6256 inode num 57603, bks cnt 2 blk size 8*512 # Located asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg Image size 22294732 inode num 57606, bks cnt 5444 blk size 8*512 ########################################################################################## ########################################################################################## ##################################### Boot image size = 22294732 (0x15430cc) bytes Using midplane macaddr Package header rev 0 structure detected Calculating SHA-1 hash...done validate_package: SHA-1 hash: calculated 4ad33773:e1cb7492:db502416:4ad586f2:7c4d9701 expected 4ad33773:e1cb7492:db502416:4ad586f2:7c4d9701 Image validated
PPC/IOS XE loader version: 0.0.3 loaded at: 00800000 01D45004 zimage at: 00807673 009B92D6 initrd at: 009BA000 01041CC9 isord at: 01042000 01D42800 avail ram: 00400000 00800000 Kernel load: Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size: 001B1C63...done. Now booting the IOS XE kernel %IOSXEBOOT-4-BOOT_SRC: (rp/0): Non-HD Boot %IOSXEBOOT-4-BOOT_PARAMETER: (rp/0): Booting with custom BOOT_PARAM setting Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-11
Configuration Examples
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre Image text-base: 0x10064AF0, data-base: 0x137E0958
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1776227K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Duplex is configured.Remove duplex configuration before enabling auto-negotiation
Press RETURN to get started! <some output removed for brevity? User Access Verification Username: user Password: Router> enable Password:
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-12
OL-16506-13
Appendix B
Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
ROM: IOS-XE ROMMON Router uptime is 1 minute Uptime for this control processor is 3 minutes System returned to ROM by reload at 15:51:54 DST Thu May 29 2008 System image file is "bootflash:packages.conf" Last reload reason: Reload command
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1776227K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Configuration register is 0x2102
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-13
Configuration Examples
Copying a Startup Configuration File to Bootflash, page B-14 Copying a Startup Configuration File to an USB Flash Disk, page B-14 Copying a Startup Configuration File to a TFTP Server, page B-15
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-14
OL-16506-13
Appendix B
43261 -rwx 208904396 May 27 2008 14:10:20 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 43262 -rwx 3172 Jul 2 2008 15:40:45 -07:00 startup-config 255497216 bytes total (40186880 bytes free)
The show redundancy states command output shows that the redundancy state is nonredundant:
Router# show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit ID = 48 Redundancy Mode (Operational) = Non-redundant Redundancy Mode (Configured) = Non-redundant Redundancy State = Non Redundant Maintenance Mode = Disabled Manual Swact = disabled (system is simplex (no peer unit)) Communications = Down Reason: Simplex mode client count = 66 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0
SSO is configured:
Router# configure terminal
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-15
Configuration Examples
Enter configuration commands, one per line. End with CNTL/Z. Router(config)# redundancy Router(config-red)# mode sso *May 27 19:43:43.539: %CMRP-6-DUAL_IOS_REBOOT_REQUIRED: R0/0: cmand: Configuration must be saved and the chassis must be rebooted for IOS redundancy changes to take effect Router(config-red)# exit Router(config)# exit Router#show *May 27 19:44:04.173: %SYS-5-CONFIG_I: Configured from console by user on console
The show redundancy states command output now indicates that SSO is configured but not operational:
Router# show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit ID = 48 Redundancy Mode (Operational) = Non-redundant Redundancy Mode (Configured) = sso Redundancy State = Non Redundant Maintenance Mode = Disabled Manual Swact = disabled (system is simplex (no peer unit)) Communications = Down Reason: Simplex mode client count = 66 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0
The show platform command output continues to show a second IOS process is still not running:
Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 R0 F0 P0 P1 Slot --------0 R0 F0 Type ------------------ASR1000-SIP10 SPA-5X1GE-V2 SPA-2XT3/E3 ASR1000-RP1 ASR1000-ESP10 ASR1004-PWR-AC ASR1004-PWR-AC CPLD Version ------------------07091401 07062111 07051680 State --------------------ok ok ok ok, active ok, active ok ok Insert time (ago) ----------------00:05:53 00:04:37 00:04:32 00:05:53 00:05:53 00:05:06 00:05:06
Router# copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK]
The router needs to be reloaded after saving the running configuration to make SSO the operational redundancy mode:
Router# reload Proceed with reload? [confirm] *May 27 19:45:16.917: %SYS-5-RELOAD: Reload requested by user on console. Reload Reason: Reload command.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-16
OL-16506-13
Appendix B
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc.
Current image running: Boot ROM1 Last reset cause: LocalSoft ASR1000-RP1 platform with 4194303 Kbytes of main memory Located packages.conf Image size 6256 inode num 43971, bks cnt 2 blk size 8*512 # Located asr1000rp1-rpbase.02.01.00.122-33.XNA.pkg Image size 22294732 inode num 43974, bks cnt 5444 blk size 8*512 ########################################################################################## ########################################################################################## ##################################### Boot image size = 22294732 (0x15430cc) bytes Using midplane macaddr Package header rev 0 structure detected Calculating SHA-1 hash...done validate_package: SHA-1 hash: calculated 4ad33773:e1cb7492:db502416:4ad586f2:7c4d9701 expected 4ad33773:e1cb7492:db502416:4ad586f2:7c4d9701 Image validated
PPC/IOS XE loader version: 0.0.3 loaded at: 00800000 01D45004 zimage at: 00807673 009B92D6 initrd at: 009BA000 01041CC9 isord at: 01042000 01D42800 avail ram: 00400000 00800000 Kernel load: Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size: 001B1C63...done. Now booting the IOS XE kernel %IOSXEBOOT-4-BOOT_SRC: (rp/0): Non-HD Boot %IOSXEBOOT-4-BOOT_PARAMETER: (rp/0): Booting with custom BOOT_PARAM setting Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-17
Configuration Examples
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1004 (RP1) processor with 752227K/6147K bytes of memory. 5 Gigabit Ethernet interfaces 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 937983K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. 253424K bytes of USB flash at usb0:.
Press RETURN to get started! <some output omitted for brevity> User Access Verification Username: user Password: Router> enable Password:
The show platform command output now indicates a second IOS process is active on RP 0:
Router# show platform Chassis type: ASR1004 Slot --------0 0/0 0/1 Type ------------------ASR1000-SIP10 SPA-5X1GE-V2 SPA-2XT3/E3 State --------------------ok ok ok Insert time (ago) ----------------00:29:34 00:28:13 00:28:18
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-18
OL-16506-13
Appendix B
ASR1000-RP1
The show redundancy states command shows SSO as the operational redundancy mode:
Router# show redundancy states my state = 13 -ACTIVE peer state = 8 -STANDBY HOT Mode = Duplex Unit ID = 48 Redundancy Mode (Operational) = sso Redundancy Mode (Configured) = sso Redundancy State = sso Maintenance Mode = Disabled Manual Swact = enabled Communications = Up client count = 66 client_notification_TMR = 30000 milliseconds RF debug mask = 0x0
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-19
Configuration Examples
ROM: IOS-XE ROMMON Router uptime is 2 weeks, 2 hours, 54 minutes Uptime for this control processor is 1 hour, 7 minutes System returned to ROM by reload at 15:24:15 DST Mon Jul 21 2008 System image file is "bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin" Last reload reason: redundancy force-switchover
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772131K/6147K bytes of memory. 8 FastEthernet interfaces 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Configuration register is 0x2102 Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Jul 21 2008 15:29:25 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 13 -rw7516 Jul 2 2008 15:01:39 -07:00 startup-config 14 -rw45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (76644352 bytes free) Router# dir stby-bootflash: Directory of stby-bootflash:/ 11 87937 14657 29313 12 drwx drwx drwx drwx -rw16384 4096 4096 4096 33554432 Dec Jul Jul Dec Dec 13 17 17 13 13 2004 2008 2008 2004 2004 03:45:47 16:43:34 16:43:34 03:53:00 03:53:49 -08:00 -07:00 -07:00 -08:00 -08:00 lost+found .rollback_timer .installer .ssh nvram_00100
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-20
OL-16506-13
Appendix B
13 -rw208904396 Jun 5 2008 20:12:53 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 58625 drwx 4096 Jul 21 2008 15:32:59 -07:00 945377280 bytes total (276652032 bytes free)
.prst_sync
Router# copy tftp bootflash: Address or name of remote host []? 172.17.16.81 Source filename []? /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]? Accessing tftp://172.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1. bin... Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!! [OK - 209227980 bytes] 209227980 bytes copied in 329.215 secs (635536 bytes/sec) Router# copy bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin stby-bootflash: Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]? Copy in progress...CCCCCCCC <output removed for brevity> 209227980 bytes copied in 434.790 secs (481216 bytes/sec) Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 28801 drwx 4096 Jul 21 2008 15:29:25 -07:00 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 12 -rw208904396 May 28 2008 16:17:34 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 15 -rw7516 Jul 2 2008 15:01:39 -07:00 13 -rw45977 Apr 9 2008 16:48:46 -07:00 16 -rw209227980 Jul 17 2008 16:06:58 -07:00 asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin 928862208 bytes total (76644352 bytes free) Router# dir stby-bootflash: Directory of stby-bootflash:/ 11 drwx 16384 Dec 13 2004 03:45:47 -08:00 87937 drwx 4096 Jul 17 2008 16:43:34 -07:00 14657 drwx 4096 Jul 17 2008 16:43:34 -07:00 29313 drwx 4096 Dec 13 2004 03:53:00 -08:00 12 -rw33554432 Dec 13 2004 03:53:49 -08:00 13 -rw208904396 Jun 5 2008 20:12:53 -07:00 asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin 58625 drwx 4096 Jul 21 2008 15:32:59 -07:00 lost+found .rollback_timer .installer .ssh nvram_00100 lost+found .ssh .rollback_timer .prst_sync .installer
startup-config target_support_output.tgz.tgz
.prst_sync
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-21
Configuration Examples
14 -rw209227980 Jul 17 2008 16:16:07 -07:00 asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin 945377280 bytes total (276652032 bytes free) Router# issu loadversion rp 1 file stby-bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting system installation readiness checking --Finished system installation readiness checking --- Starting installation changes --Setting up image to boot on next reset Starting automatic rollback timer Finished installation changes SUCCESS: Software will now load. Router# *Jul 21 23:34:27.206: %ASR1000_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Jul 21 23:34:27.271: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Jul 21 23:37:05.528: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R1 *Jul 21 23:37:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Jul 21 23:37:25.480: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) Finished installation state synchronization
*Jul 21 23:37:26.349: %REDUNDANCY-3-IPC: IOS versions do not match. *Jul 21 23:38:47.172: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Jul 21 23:38:47.173: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# issu runversion --- Starting installation state synchronization --Finished installation state synchronization Initiating active RP failover SUCCESS: Standby RP will now become active Router#
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc. <additional output removed for brevity> *Jul 21 23:43:31.970: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-22
OL-16506-13
Appendix B
Compiled Thu 01-May-08 00:29 by mcpre *Jul 21 23:43:31.978: %SSH-5-ENABLED: SSH 1.99 has been enabled *Jul 21 23:43:35.196: Relay: standby progression done *Jul 21 23:43:35.197: %PLATFORM-6-RF_PROG_SUCCESS: RF state STANDBY HOT
At this point of the process, the user has to log onto RP1, which started the upgrade as the standby RP but is the active RP after the switchover. The following commands are entered from RP1:
Router# issu acceptversion Cancelling rollback timer SUCCESS: Rollback timer cancelled Router# issu commitversion --- Starting installation changes --Cancelling rollback timer Saving image changes Finished installation changes
Building configuration... [OK] SUCCESS: version committed: bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Tue 08-Jul-08 14:40 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
ROM: IOS-XE ROMMON Router uptime is 2 weeks, 3 hours, 8 minutes Uptime for this control processor is 11 minutes System returned to ROM by reload at 15:29:24 DST Mon Jul 21 2008 System image file is "bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin" Last reload reason: EHSA standby down
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-23
Configuration Examples
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772046K/6147K bytes of memory. 8 FastEthernet interfaces 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 937983K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. 253424K bytes of USB flash at usb0:. Configuration register is 0x2102 Router# show running-config | include boot boot-start-marker boot system bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin boot system bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin boot-end-marker Router#
At this point of the procedure, the upgrade of RP1 is complete. The following procedure uses the same steps to upgrade RP0. The user is still on RP1 when this process begins:
Router# show platform Chassis type: ASR1006 Slot --------0 0/0 0/1 0/2 1 1/0 1/1 1/2 R0 R1 F0 F1 P0 P1 Slot --------0 1 R0 R1 F0 F1 Type ------------------ASR1000-SIP10 SPA-5X1GE-V2 SPA-8X1FE-TX-V2 SPA-2XCT3/DS0 ASR1000-SIP10 SPA-2XOC3-POS SPA-8XCHT1/E1 SPA-2XT3/E3 ASR1000-RP1 ASR1000-RP1 ASR1000-ESP10 ASR1000-ESP10 ASR1006-PWR-AC ASR1006-FAN CPLD Version ------------------06120701 06120701 07082312 07062111 07051680 07051680 State --------------------ok ok ok ok ok ok ok ok ok, standby ok, active ok, standby ok, active ok ok Insert time (ago) ----------------00:16:10 00:10:50 00:10:46 00:10:42 00:16:10 00:10:49 00:10:45 00:10:41 00:16:10 00:16:10 00:16:10 00:16:10 00:15:07 00:15:07
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-24
OL-16506-13
Appendix B
Router# issu loadversion rp 0 file stby-bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin --- Starting installation state synchronization --Finished installation state synchronization --- Starting file path checking --Finished file path checking --- Starting system installation readiness checking --Finished system installation readiness checking --- Starting installation changes --Setting up image to boot on next reset Starting automatic rollback timer Finished installation changes SUCCESS: Software will now load. Router# *Jul 21 23:53:41.218: %ASR1000_OIR-6-OFFLINECARD: Card (rp) offline in slot R0 *Jul 21 23:53:41.256: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) *Jul 21 23:53:41.256: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) *Jul 21 23:53:41.256: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE) *Jul 21 23:53:42.423: %IP-4-DUPADDR: Duplicate address 172.29.52.155 on GigabitEthernet0, sourced by 001a.3046.e3ff *Jul 21 23:56:19.885: %ASR1000_OIR-6-ONLINECARD: Card (rp) online in slot R0 *Jul 21 23:56:39.324: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4)) *Jul 21 23:56:39.324: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5)) *Jul 21 23:58:03.660: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Jul 21 23:58:03.661: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) Router# issu runversion --- Starting installation state synchronization --Finished installation state synchronization Initiating active RP failover SUCCESS: Standby RP will now become active Router#
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2008 by cisco Systems, Inc. <Output removed for brevity>
After the switchover, the user must log onto RP0. The remaining commands are all entered from RP0:
Router# issu acceptversion Cancelling rollback timer SUCCESS: Rollback timer cancelled Router# issu commitversion
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-25
Configuration Examples
*Jul 22 00:10:45.488: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded *Jul 22 00:10:45.489: %RF-5-RF_TERMINAL_STATE: Terminal state reached for (SSO) --- Starting installation changes --Cancelling rollback timer Saving image changes Finished installation changes
Building configuration... [OK] SUCCESS: version committed: bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin Router# show version Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Tue 08-Jul-08 14:40 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.
ROM: IOS-XE ROMMON Router uptime is 2 weeks, 3 hours, 33 minutes Uptime for this control processor is 16 minutes System returned to ROM by reload at 15:24:15 DST Mon Jul 21 2008 System image file is "bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin" Last reload reason: EHSA standby down
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco ASR1006 (RP1) processor with 1772046K/6147K bytes of memory. 8 FastEthernet interfaces 5 Gigabit Ethernet interfaces 8 Serial interfaces 8 Channelized T1 ports 2 Packet over SONET interfaces 2 Channelized T3 ports 32768K bytes of non-volatile configuration memory.
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-26
OL-16506-13
Appendix B
4194304K bytes of physical memory. 921599K bytes of eUSB flash at bootflash:. 39004543K bytes of SATA hard disk at harddisk:. Configuration register is 0x2102 Router# show running-config | include boot boot-start-marker boot system bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin boot system bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin boot-end-marker Router#
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
B-27
Configuration Examples
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
B-28
OL-16506-13
INDEX
Symbols
<cr>
8 8
11
no form, using
? command
6 7
A
access interface input and output hold queue ASR1000-ESP10-N, troubleshooting Assigning a MAC Address auxiliary port, using
4 3
configuration files, backing up to bootflash configuration files, backing up to TFTP configuration files, backup example configuration files, managing
12 14 13 13
B
Bidirectional Forwarding Detection (BFD) Bridge Domain Interfaces
1 8
12
console, accessing using a direct connection console, accessing using telnet console, connecting
2 1 3 3
C
Call Admission Control displaying
37 8 6 5 5 5
11 7
consolidated package, managing and configuring using request platform software package install command 8 consolidated package, managing and configuring using the copy command 7 consolidated package, running the router using consolidated package boot using TFTP, example consolidated packages, managing and configuring
6 2 6 1 6
Cisco ASR1002 Series Router, software compatibility Cisco ASR1006 Series Router, software compatibility Cisco IOS configuration changes, saving command-line interface, getting help command line processing commands context-sensitive help for abbreviating
8 5 8 12
2 2 5
OL-16506-13
IN-I
Index
5 5
H
9 7 7 7 9
copy command, command set overview CPP driver process, overview CPP HA process, overview CPP SP process, overview crashinfo files, overview
D
device IDs call home format
43 7
I
IDs serial IDs
43 2
E
e-mail notifications Call Home
59 3 18
ESPBase, Overview
IOS process, enabling second IOS process on single RP example 15 IOS process, overview IP Forwarding
4 7 6 8
F
field programmable hardware device upgrade file management, command set overview Files, autogenerated files file systems, overview flush, on input interface
8 13 9 4 5
IP Sessions Scaling
ISSU, consolidated package upgrade example ISSU, sub-packages dual RP ISSU, upgrade procedures
7
G
global configuration mode, summary of
6
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
IN-II
OL-16506-13
Index
K
keepalive command keyboard shortcuts
5 6
PPP Session and L2TP Tunnel Scaling privileged EXEC mode, summary of processes, overview prompts, system
6 6 6
L
LACP over EVC port channel configuration commands, configuration steps
13 8, 9, 11,
Q
question mark (?) command
8
Layer 4 Redirect
4 4 6 9
R
RADIUS attribute interface-config
7 8
M
Management Ethernet Interface, common tasks
3 2 2
ip-unnumbered vrf-id
8
redundancy, hardware redundancy overview redundancy, software redundancy overview release notes See platforms, supported request platform command set, overview rommon image, overview
5 7 6 4
2 4
Management Ethernet interface, interface numbering Management Ethernet interface, IP Address Handling Management Ethernet interface, overview Management Ethernet Interface, VRF modem, accessing modes See command modes
4 3 2
Restrictions for the Bridge Domain Interface ROM monitor mode, summary of RPAccess, Overview RPBase, Overview
3 3 3
Monitoring and Maintaining Frame Relay and Multilink Frame Relay 2 Multilink Frame Relay
2
RPControl, Overview
N
no virtual-template snmp command
6
RPIOS, Overview
P
Packet Forwarding platforms, supported release notes, identify using
15 7 4
S
scalability configuring the access interface input and output hold queue 6 Secure Shell (SSH), configuring persistent SSH
8
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-13
IN-III
Index
2 16 11
telnet, using
3 3 11 5
Secure Shell (SSH), persistent SSH restrictions serial IDs description server IDs description
44 7 43
TFTP, copying consolidated package to example tracelogs directory, overview Tracing, how tracing works Tracing, overview
1 4 5
shell manager process, overview show history command SIPBase, Overview SIPSPA, Overview
3 3 3 1
Software Modules, Overview Software Packaging, Overview source IDs call home event format SPA driver process, overview
43
U
upgrading field programmable hardware device user EXEC mode, summary of
6 5
SSO, using SSO to enable second IOS Process on single RP example 15 Stateful Switchover (SSO), overview
7
Stateful Switchover, Supported Protocols and Applications 7 sub-package, copying and booting sub-package boot, example
10 14
V
VPDN vpdn ip udp ignore checksum command
7 7 6
sub-package extraction to different file system, example 9 sub-package extraction to same file system, example sub-packages, extracting modules from image sub-packages, managing and configuring sub-packages, restrictions
3 2 10 10
W
web user interface (graphics-based), overview web user interface (legacy), overview web user interface, accessing web user interface, DNS
7 1 10 9 5 8 7 2 3
sub-packages, running the router using sub-packages, upgrading individual Synchronous Ethernet Support
2 18
T
Tab key, command completion telnet, persistent
2 16 8 5
web user interface, using auto-refresh web user interface access, configuring
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
IN-IV
OL-16506-13