Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DM-3090
SERVICE MANUAL
1997-11/B51-5396-00 (K/K) 1812
REC
REC LEVEL
10
TIMER/ DELETE
TIME DISPLAY ON/STAND BY DISPLAY/CHARAC. TRACK/EDIT
ENTER
PHONES
Panel (A29-0898-08)
Knob (K27-2262-08)
DIGITAL
LINE
OPT. 2 REC IN
PLAY OUT
PLAY OUT
REC IN
1 REC IN
RESET
DM-3090
CONTENTS/ACCESSORIES/CAUTIONS
CONTENTS
CONTENTS/ACCESSORIES/CAUTIONS...................2 CONTROLS .................................................................3 DISASSEMBLY FOR REPAIR.....................................5 BLOCK DIAGRAM .......................................................7 CIRCUIT DESCRIPTION .............................................9 TROUBLE SHOOTING ..............................................16 ADJUSTMENT ...........................................................24 PC BOARD ............................................................... 32 SCHEMATIC DIAGRAM ........................................... 37 EXPLODED VIEW .....................................................47 PARTS LIST...............................................................49 SPECIFICATIONS .......................................Back cover
Accessories
Audio cord (2) (E30-0505-05) Optical fiber cable (1) (B19-1529-05)
Batteries (2)
Cautions
Beware of condensation
When water vapor comes into contact with the surface of cold material, water drops are produced. If condensation occurs, correct operation may not be possible, or the unit may not function correctly. This is not a malfunction, however, and the unit should be dried. (To do this, turn the POWER switch ON and leave the unit as it is for several hours.)
+10
If a problem occurs
If this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction or the display may not function correctly. If such a problem occurs, do the following:
Unplug the AC power lead from the AC socket. Wait about 20 - 30 seconds and then plug the AC power lead back into the AC socket. Press the reset key on the back of the unit.
DIGITAL PLAY LINE REC IN
OPT. 2
REC IN PLAY OUT
OUT
REC IN
R
RESET
RESET
When the reset key is pressed, all of the settings in memory will be erased.
DM-3090
CONTROLS
^ %
$
REC
#
REC LEVEL
10
TIMER/ DELETE
TIME DISPLAY ON/STAND BY DISPLAY/CHARAC. TRACK/EDIT
ENTER
PHONES
1
1 Eject key:
4 5 6
9 ENTER key
7 8 9
0 !
2 Power switch (ON/STAND BY key) 3 Mini Disc Insertion slot 4 TIME DISPLAY key 5 DISPLAY/CHARAC key 6 TRACK/EDIT key 7 TIMER/DELETE key 8 Jog dial (Next/Previous)
0 Headphone jack (HONES) ! Headphone output level control @ Record level control # Record key: $ Play/Pause key: % Stop key: ^ Cue/Review key: /
Display
( * & ^ %
1 2
TOC
DISC
TRACK
DATE
12
0dB
OVER
MONO LP PRGM
TIMER REC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 CLOCK 15 16 17 18 19 20
$ #
3 4
1 Pause indicator: 2 Record indicator: 3 Play indicator:
5 6 8 7
! Music Calendar @ More Tracks indicator # Recording Level indicator $ Recording level too high indicator % Level Meter/Character Information display ^ Date indicator & Track indicator * Disc Name indicator ) TOC Indicator: TOC
4 Monaural Long-Play Mode indicator 5 Programme indicator 6 Repeat indicator: 7 Total Time/Remaining Time indicator 8 Random indicator 9 Timer Playback/Timer Recording indicator 0 Clock indicator
DM-3090
CONTROLS
Remote control unit
The remote control unit incorporates the basic operation keys as well as a variety of applied operation keys so that it can be used in a wide range of purposes. Use care to store the remote control unit in a safe place so as not to lose it.
1
1 POWER key 2 EJECT key 3 Numeric keys 5 Applied operation keys
ENTET: Entet key
EJECT
POWER
DISPLAY
TIME DISPLAY
+10
REC INPUT
REC MODE
AUTO MARK
REC CANCEL
SYNCHRO REC
6 5 4
SELECT PROGRAM
REC
CLEAR
PLAY MODE
7 Display keys
DISPLAY : Display key TIME DISPLAY : Time display key
PHONES LEVEL
PHONES
MIN
MAX
DM-3090
DISASSEMBLY FOR REPAIR
REMOVING AND REINSTALLING THE MAIN PARTS
MD MECHANISM SECTION
Perform steps 1 to 3 of the disassembly method to remove the MD mechanism.
(A1)x1 1.7x5mm
Magnetic Head
MD Mechanism
Figure 10-1
Slider Lever Roller Arm Lever Loading Motor Clampa Lever Cartridge Holder (B1) x1 1.7x5mm
Lack Gear
(B2) x1
Figure 10-2
(C1)x1 1.7x3mm (C1)x1 1.7x9.5mm
Figure 10-3
DM-3090
DISASSEMBLY FOR REPAIR
How to remove the sled motor/loading motor (See Fig. 11-1)
1. Remove the screws (D1) x 1 pcs., and remove the sled motor/loading motor. Caution: Be careful so that the gear is not damaged. (The damaged gear emits noise during searching.)
(D1)x2 1.7x2mm (D1)x2 1.7x2mm
Loading Motor
Sled Motor
Figure 11-1
Spindle Motor
Figure 11-2
(F1)x3 1.7x9.5mm Optical Pickup
Figure 11-3
D4.3V
D3.2V
MD
M901 SPINDLE MOTOR
M
M902 SLED MOTOR
IC1906 AND GATE TC7ST08F IC1907 CLOCK GENERATOR TC92ASF IC1990 INVERTOR 74AC04FS
CNP1902 LIGHT RECEIVING SECTION ERROR SIGNAL LIGHT RECEIVING SECTION RF TRACKING F EFSIGNAL ABSIGNAL A B E RF1 RF1 ~ RF4SIGNAL RF2 RF3 RF4 LASER DIODE MONITOR DIODE
WRITE PRO DIRECT SWITCH SW1952 LEAD INSWITCH SW1953 PLAYSWITCH SW1954 RECSWITCH SW1955 LOADING SWITCH SW1956
D3.2V
IC1202 IX2474AF
4M DRAM
D3.2V IC1402 S29294A E2PROM
MECHAN1SM 6.5/4.75~5.25V
DIGITAL 3.2V
D4.3V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PDOWN BACKUP LOAD IN RESET MD-ST DSCK SERCH KDATA MDDATA DSTB D.GND D.GND D.GND D.GND DVDD DVDD SYSCLK ADDATA LRCLK BCLK DADATA DFS1 DFS0 MUTE
BLOCK DIAGRAM
DM-3090
M
LOADING MOTOR HEAD UP/DOWN D6.5/4.75 ~ 5.25V
DM-3090
BLCK DA DATA
MODE CLK
DATA
S-ID,SYN,RESET,DSTB,DSCK
FL901
FL DISPLAY +B
K-DATA,MD DATA
MUTE
MD
8
LINE IN J101 J101 LINE OUT Q451 Q452 IC101 NJM4560D OPE AMP MUTE
3 5 8
1 7 4
24 26
3 5 4 8
-7V +7V
-7V +7V
10 2 13 ~ 15
1 7
Q601 Q602
5 3 8 4
7 1
H.P.VOL VR981 HEADPHINES J981
+7V
-7V
3V
J301 13 DIGITAL -IN (COAXIAL JACK) SO302 DIGITAL IN (OPTICAL JACK) RX302 DIGITAL OUT (OPTICAL JACK)
17 ~ 21
3 1
2
IC501 REGULATOR S81233YK Q503 A+7V POWER CIRCUIT
BLOCK DIAGRAM
13 10 2
DIGITAL IN
MD UNIT
DIGIN VCC DIGITAL OUT A-7V POWER CIRCUIT T551 POWER TRANSFORMER
Q502
Q506
DIGITAL 5V BACK UP 5V
21 ~ 42 60 ~ 89
SW901 JOG SWITCH JOG DIG SEG
45 ~ 90 92 ~ 97
10
33 96 100 91
FL VP(-31V)
KEY IN BLOCK
2 3
KEY
FL POWER CIRCUIT
A/D +5V
32 RX-IN
DM-3090
CIRCUIT DESCRIPTION
IC1101 VHiiR3R55//-1:RF Signal Control (IR3R55)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15* 16* 17* 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34* 35 36 37 38 39 40 41* 42 43 44 45 46* 47 48 Terminal Name RF1 RF2 RF3 RF4 REFI REFO RFADD TCGI AIN BIN EIN FIN BIAS AVCC VSTBY XDISC XSGAIN AGND DGND DTEMP LATCH CLOCK DATA DVCC FOUT EOUT BOUT AOUT TCGO WBO 22KI 22KO ADLPFO NC ADIPO ADIPI ADAGC ADAGI RF2-1 EFMO WFMI AVCC AGND EFMAGC EFMAGI ATTR GOUT POUT I/O I I I I I O O I I I I I I O O O I I I O O O O O O I O O O O I O O I O O Function RF signal input terminal 1 Input of RF signal output of pickup RF signal input terminal 2 Input of RF signal output of pickup RF signal input terminal 3 Input of RF signal output of pickup RF signal input terminal 4 Input of RF signal output of pickup Reference voltage amp. input terminal Reference voltage amp. output terminal RF1 to 4 resistance addition output terminal Track cross detection signal amp. input terminal for groove Servo signal amp. (focus servo system) inversion input terminal Servo signal amp. (focus servo system) inversion input terminal Servo signal amp. (tracking servo system) inversion input terminal Servo signal amp. (tracking servo system) inversion input terminal Bias input terminal Analog section power terminal Logic signal output terminal (STBY signal inversion signal is output.) Logic signal output terminal (DISC signal inversion signal is output.) Logic signal output terminal (SGAIN signal inversion signal is output.) Analog section GND terminal Digital section GND terminal Chip temperature detection terminal Latch signal input terminal Clock signal input terminal Serial data input terminal Digital section power terminal Servo signal amp. (tracking servo system) output terminal Servo signal amp. (tracking servo system) output terminal Servo signal amp. (focus servo system) output terminal Servo signal amp. (focus servo system) output terminal Track cross detection signal amp. output terminal for groove Comparator output terminal for ADIP signal binary-coding Comparator input terminal for ADIP signal binary-coding ADIP signal HPF amp. output terminal ADIP signal LPF amp. output terminal NC ADIP signal primp. output terminal ADIP signal AGC amp. output terminal ADIP signal AGC smoothing capacitor connection terminal ADIP signal AGC amp. input terminal RF1 and RF2 difference signal RF signal primp. output terminal RF signal AGC amp. output terminal Analog section power terminal Analog section GND terminal EFM signal AGC smoothing capacitor connection terminal EFM signal AGC amp. output terminal Pins 47 and 48 output signal attenuation terminal Output of signal of RF1+RF2-RF3-RF4 for groove Rf1 to 4 resistance addition output for pit
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
DM-3090
CIRCUIT DESCRIPTION
IC1201 VHiLR37648/-1:ENDEC/ATRAC (LR37648)
Pin No. 1* 2 3 4 5 6 7 8 9 10* 11 12 13 14,15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30* 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47* 48* 49* 50 51* 52* 53* Terminal Name Input/Output EFMMON AVCC EFMI AGND AIN EIN TCG BIN FIN VBAT WBI VDD1 DGND TEST0,TEST1 TEST2 X176KO FODRF FODRR TRDRF LATCH CLOCK DATA DVCC FOUT EOUT BOUT AOUT TCGO WBO 22KI 22KO ADLPFO NC ADIPO ADIPI ADAGC ADAGI RF2-1 EFMO WFMI AVCC AGND EFMAGC EFMAGI ATTR GOUT POUT PLCK EFM0 X700KO EXPORT0 EXPORT1 Output Input Input Input Input Input Input Input Input Input Input Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output In/Output In/Output Output Output Output In/Output In/Output Output Output Output Output Output Output Output EFM monitor output Analog power EFM signal input from RF amp. Analog GND Focus error signal A Tracking error signal E Track cross signal Focus error signal B Tracking error signal F Power voltage detection signal for constant voltage servo ADIP wobble signal Digital power Digital GND Input for test. Connection to GND in case of normal use Input for test. Endecode/servo mode and ATRAC mode selection Clock output. f=176.4 kHz (4fs) Focus servo forward output. PWM Focus servo reverse output. PWM Tracking servo forward output. PWM Tracking servo reverse output. PWM Slide servo forward output. PWM Slide servo reverse output. PWM Spindle servo forward output or spindle servo output. PWM Spindle servo reverse output or spindle rotation (forward/reverse)selection Address output to external D-RAM. ADR3 Address output to external D-RAM. ADR2 Address output to external D-RAM. ADR1 Address output to external D-RAM. ADR0 (LSB) Address output to external D-RAM. ADR10 (MSB) Power supply for DRAM interface Address output to external D-RAM. ADR4 Address output to external D-RAM. ADR5 Address output to external D-RAM. ADR6 Address output to external D-RAM. ADR7 Address output to external D-RAM. ADR8 Data output enable signal output to external D-RAM Digital GND Column address strobe signal output to external D-RAM Data input/output from and to external D-RAM. D2 Data input/output from and to external D-RAM. D3 (MSB) Data input/output from and to external D-RAM. ADR9 Low address strobe signal output to external D-RAM Data write enable signal output to external D-RAM Data input/output from and to external D-RAM. D1 Data input/output from and to external D-RAM. D0 (LSB) Track cross signal ADIP CRC error flag monitor output EFM PLL clock output in playback mode EFM signal output in record mode. C1F (C1 error flag) monitor output in playback mode Clock output. f = 705.6 kHz. Clock output is not performed when RSTX = 0. Microcomputer extension output port 0 Microcomputer extension output port 1 Function
10
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
DM-3090
CIRCUIT DESCRIPTION
Pin No. 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75* 76* 77* 78* 79* 80* 81 82 83 84 85 86 87 88 89 90 91~96 97 98 99 100 Terminal Name Input/Output TESO1 TESO3 TEST4 CDDATA CDLRCK CDBCLK VXI VPO VDD1 DGND XI XO DIN DOUT VDD3 DGND LRCK BLCK DFCK ADDATA DADATA FEMON TOTMON TEMON SBCK SBO SBSY SFSY FOK SENSE COUT MCCK DINTX VDD1 DGND RSTX SYD0 SYD1~SYD6 SYD7 SYWRX SYRDX SYRS Output In/Output In/Output In/Output In/Output In/Output Input Output Input Output Input Output Output Output Output Input Output Output Output Output Input Output Output Output Output Output Output Output Output Input In/Output In/Output In/Output Input Input Input Function PLLLR. Microcomputer extension output port 2 in case of selection PLLOSC. Microcomputer extension output port 3 in case of selection EXTCLK. Microcomputer extension output port 4 in case of selection High speed dubbing CD data input. Microcomputer extension output port 5 in case of selection High speed dubbing CD LR data input. Microcomputer extension output port 6 in case of selection High speed dubbing CD bit data input. Microcomputer extension output port 7 in case of selection Vari-pitch PLL clock input Vari-pitch PLL phase error output Digital power Digital GND Oscillation circuit input. 33.8688 MHz Oscillation circuit input. 33.8688 MHz Digital input signal Digital output signal Power for internal PLL Digital GND Music data Lch/Rch selection output Music data shift clock AD/DA converter digital filter clock. 256 Fs Audio data input Audio data output Focus error signal monitor output Total signal monitor output Tracking error signal monitor output DIN subcode read clock. EIAJ CP-309 Format DIN subcode serial data. EIAJ CP-309 Format DIN subcode block sync signal. EIAJ CP-309 Format DIN subcode frame sync signal. EIAJ CP-309 Format Focus OK detection signal. "0" : Focus OK Servo status detection signal. "1": Auto-move, auto-jump, auto-focus retraction Track cross signal output Microcomputer clock output. Clock output is performed also when RSTX = 0. System controller interface interruption request output terminal Digital power Digital GND Chip reset input. "L": Reset System controller interface data bus terminal (LSB) System controller interface data bus terminal System controller interface data bus terminal (MSB) System controller interface register writing pulse input System controller register read pulse input System controller interface register selection input
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
11
DM-3090
CIRCUIT DESCRIPTION
IC1401 RX-iX0227AWZZ:MD System Microcomputer (IX0227AW)
Pin No. 1* 2* 3 4* 5* 6 7 8 9 10* 11* 12 13* 14 15 16 17 18 19 20 21 22 23* 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41* 42 43 44 45 46 47 48 49 50 51 Terminal Name Input/Output P96/ANEX1 P95/ANEX0 P94/DA1 P93/DA0 P92/TB2IN P91/TB1IN P90/TB0IN BYTE CNVss P87/XCIN P86/XOUT RESET XOUT Vss XIN Vcc P85/NMI P84/INT2 P83/INT1 P82/INT0 P81/TA4IN P80/TA4OUT P77/TA3IN P76/TA3OUT P75/TA2IN P74/TA2OUT P73/TA1IN P72/TA1OUT P71/TA0IN P70/TA0OUT P67/TXD1 P66/RXD1 P65/CLK1 P64/CTS1/RTS1/ CTS0/CLKS1 P63/TXD0 P62/RXD0 P61/CLK0 P60/CTS0/RTS0 P57/RDY/CLKOUT P56/ALE WFMI AVCC AGND EFMAGC EFMAGI ATTR GOUT POUT PLCK EFM0 X700KO Output Output Output Output Output Input Input Input Input Output Output Input Input Input Input Input Input Input Output Input Output Input Output Output Output Input Input Output Output Output Output Output Input Input Input Output Input Input/Output Output Output Output Output Output In/Output In/Output In/Output In/Output In/Output Not used Not used LDVAR (laser power adjustment output) ADJS (for automatic adjustment step check) Not used LD SW CK input (interruption input only in single state) ERR input (monitor PLL UNLOCK) GND GND ST-ID Output MD search output RESETInput Extal clock output GND EXTAL (8.4672 MHz) + 3.15V Connect +B DINT (interruption input from MD LSI) DSENSE (servo sense input from MD LSI) ST-ID Input (MD-ON) CD search input (syncro REC suspension input from MD LSI) MD RSW Output FSW1 (SW power frequency selection) Vari-pitch correspondence given (H)/not given (L) P-DOWN (power failure detection) HDON (magnetic head current ON/OFF output) LD+ (loading motor + control output) LD- (loading motor + control output) CIN (track count signal input) INN SW (inner SW detection input) R-DATA R-LATCH R-CLK DSTB (system controller communication enable and communication beingexecuted) MD DATA (MD Data Output) K DATA (system controller data input) DSCK (system controller communication clock input) 4M/16M DRAM selection input R/P output (REC/PLAY selection) FOK (focus servo status monitor input) Not used S2 Ouput S1 Output SYRS (MD-LSI register selection signal output) SYRD (MD-LSI read signal output) SYWR (MD-LSI right signal output) SYS D7 (data bus 7) SYS D6 (data bus 6) SYS D5 (data bus 5) SYS D4 (data bus 4) SYS D3 (data bus 3) Function
12
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
DM-3090
CIRCUIT DESCRIPTION
Pin No. 52 53 54 55* 56* 57* 58 59 60 61 62 63* 64 65* 66* 67* 68* 69* 70 71* 72 73 74* 75* 76 77 78* 79* 80 81* 82* 83* 84 85* 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Terminal Name Input/Output P42/A18 P41/A17 P40/A16 P37/A15 P36/A14 P35/A13 P34/A12 P33/A11 P32/A10 P31A9 Vcc P30/A8 Vss P27/A7 P26/A6 P25/A5 P24/A4 P23/A3 P22/A2 P21/A1 P20/A0 P17/D15 P16/D14 P15/D13 P14/D12 P13/D11 P12/D10 P11/D9 P10/D8 P07/D7 P06/D6 P05/D5 P04/D4 P03/D3 P02/D2 P01/D1 P00/D0 P107/AN7/KI3 P106/AN6/KI2 P105/AN5/KI1 P104/AN4/KI0 P103/AN3 P102/AN2 P101/AN1 AVss P100/AN0 VREF AVcc P97/ADTRG In/Output In/Output In/Output Output Output Output Output Output In/Output Output Input Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Input Input Input Input Input Input Input Input Input Input Input Input SYS D2 (data bus 2) SYS D1 (data bus 1) SYS D0 (data bus 0) Not used Not used Not used EEPRO (EEPROM protection cancel) EPCS (EEPROM chip selector output) EEPD (EEPROM sirial data output) EEPK (EEPROM sirial colck output) + 3.15V Not used GND L3 DATA (soft serial communication, 2 modes provided, LSB fast) L3 MODE (soft serial communication, 2 modes provided, LSB fast) L3 CLK (soft serial communication, 2 modes provided, LSB fast) Not used Not used PCNT0 output Not used LDON output (H: ON) ANLPTR output ADPON output (for CK) DAPON output (for CK) DFS0 output DFS1 output DIG EX output (for CK) DIG CD output (for CK) XRST (system reset output) AD MUTE output (for CK) EMPHA output (for CK) DA MUTE output (for CK) MUTE output DOUTM output (for CK) TEST2 (special mode selection 2) TEST1 (special mode selection 1) TEST0 (special mode selection 0) AVCK3 (special mode monitor input) AVCK2 (AD/DA section 3.1V monitor input) AVCK1 (DOUT section 5V monitor input) DTEMP (temperature detection input) MINF (disc type/REC input) TEST K1 (test key input 1) TEST K2 (test key input 2) GND HINF (mechanism position/HEAD position) + 3.15V + 3.15V Connect +B Function
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
13
DM-3090
CIRCUIT DESCRIPTION
IC901 RH-iX0196AFZZ: System Control Microcomputer (iX0196AW)
Pin No. 1* 2 3 4* 5 6 7*,8* 9* 10 11* 12* 13* 14 15 16 17* 18 19 20 21 22 23 24* 25* 26* 27* 28* 29 30* 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Port Name P77/AN7 P76/AN6 P75/AN5 P74/AN4 P73/AN3 P72/AN2 P71/AN1,P70/AN0 PB3 PB2/DA P57/SRDY3/AN15 P56/SCLK3/AN14 P55/SOUT3/AN13 P54/SIN3/AN12 P52/SRDY2/AN11 P52/SCLK2/AN10 P51/SOUT2/AN9 P50/SIN2/AN8 P67/SRDY1/CS/ SCLK12 P66/SCLK1 P65/SOUT1 P64/SIN1 P63/CNTR1 P62/CNTR0 P61/PWM P60 P47/T3OUT P46/T1OUT P45/INT1/2CR P44/INT4 P41 P42/INT2 P41 P40/INT0 RESET PB1/Xcin PB0/Xcout Xin Xout VSS P27 P26 P25 P24 Terminal Name Input/Output KEY1 KEY2 KEY3 INI JOG_AD DIG SEL1 DIG SEL2 DAC_MODE DAC_CLK/EX DAC_DATA/EX DFS0/DFS1 DSTRB DSCK K-DATA MD-DATA MD-LO/EJ P IN P.CNT P-OUT RX-IN P-MUTE RESET Xcin Xcout Xin Xout VSS SERCH LOAD S-ID MD RESET Output Input Input Output Input Input Output Output Output Output Output Output Output Output Output Output Input Input Output Output Input Output Output Output Output Output Output Input Output Output Input Output Input Input Input Output Input Output Input Output Input Output Output Not used Key entry Key entry Not used Initial setting entry Jog dial entry Not used Not used Digital signal selector selection signal Not used Not used Not used Externally provided DAC/ADC serial interface mode signal Externally provided DAC/ADC serial interface clock signal Externally provided DAC/ADC serial interface clock signal Not used EMPHASIS information from MD MD serial interface strobe signal MD serial interface clock signal MD serial interface transmission signal MD serial interface reception signal MD loading power voltage selection signal Not used Not used Not used Not used Not used Power failure detection Power control MD power failure detection signal Remote control loght reception signal Audio mute control signal GND RESET signal entry Sub clock IN connection (32.7k) Sub clock OUT connection (32.7k) Main clock IN connection (8M) Main clock OUT connection (8M) GND CD to MD search monitor signal MD loading detection CD to MD start ID signal RESET signal to MD Function
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
14
DM-3090
CIRCUIT DESCRIPTION
Pin No. 45-54 55,56 57-60 61-64 65-72 72-80 81-88 89,90 91 92-97 98 99 100 Port Name P23/DIG19P12/DIG10 P11/SEG41/DIG9, P10/SEG40/DIG8 P07/SEG39/DIG7P04/SEG36/DIG4 P05/SEG35/DIG3P00/SEG33/DIG0 P37/SEG31P30/SEG25 P97/SEG23P90/SEG16 P87/SEG15P80/SEG8 PA7/SEG7, PA6/SEG6 VCC PA5/SEG5PA0/SEG0 VEE AVSS VREF Terminal Name Input/Output UDIG0-UDIG9 UDIG10,UDIG11 UDIG12-UDIG15 S35-S32 S31-S25 S0-S8 S9-S16 S17,S18 VCC S19-S24 VEE AVSS VREF Output Output Output Output Output Output Output Output Input Output Input Input Input Digit for FL drive Digit for FL drive Digit for FL drive Segment for FL drive Segment for FL drive Segment for FL drive Segment for FL drive Segment for FL drive +5V Segment for FL drive -30V GND +5V Function
15
DM-3090
TROUBLE SHOOTING
When an error message is displayed, proceed as follows:
Error messages
BLANK MD Can't COPY Can't EDIT Can't REC DEFECT Din UNLOCK DISC ERR
Meaning
Nothing is recorded. No copy can be made because of the SCMS copyright system. A track cannot be edited.
Remedy
Replace the MD wiht a recoded disc. Record using the analogue cable.
Change the stop position of the track and then try editing it. Stop vibration and try again.
Since this MD has scratches on it, the recording operation was skipped. Poor connection of the digital cable.
The disc damaged. The TOC information is not recorded on the disk or the date contains. The MD is out of recording space. A MD has not been loaded. The disc data cannot be read. There is a mechanical problem and the disc is working properly. The number of characters for the MD name or track name exceeds 40. MD has not been loaded. MD data cannot be read. The data recorded on this disc is not audio data.
DISC FULL FOCUS ERROR MECHA ERR** NAME FULL NO DISC NOT AUDIO PLAYBACK MD PROTECTED TEMP OVER TOC ERR** TOC FULL** TOC W ERROR U TOC ERR** U TOC W ERR
Replace the disc with another recordable disc. Reload the MD.
Reset the microprocessor referring to "If a problem occurs". Shorten the MD or track name.
Load a MD. Reload the MD. Select another track. Replace the MD. Raplace it with a recordable MiniDisc. Move the write protection tab back to its original position.
The temperature is too high. The MD is excessively damages There is no space left for recording character infomation (track names, disc names, etc.) Trouble has occurred.
Turn off the power, and wait for a whilst. Replace the disc with another disc. Replace the MD with another recordable disc.
Contact a KENWOOD Authorized Sevicing Dealer or KENWOOD Authorized Sevice station. Replace it with another MD. Erase all the data, and try recording. Turn off the power, and try to write the TOCinformation again. (Remove any source of shock or vibration whilst writing.)
The TOC infomation on this disc does not meet the MD specifications or it cannot be read. The TOC infomation could not be created properly due to a mechanical shock or to scratches on the disc.
? DISC 0-00:00
**Number or symbol
Replace the disc with another disc. Replace the disc with a recorded disc.
16
DM-3090
TROUBLE SHOOTING
EXPLANATION OF ERROR DISPLAY
Error display Can't REC Errors Corrective action Defect occurred successively 10 times during REC-PLAY. Check that the disc is free from flaw, dust As a result of occurrence of defect during REC-PLAY the and fingerprint. recordable cluster became zero. Check whether there is any black spot. Adress is unreadable. REC state connot be set for 20 seconds Check for disc disalignment and run-out. although retry is repeated. The following judgement is made according to the channel status of digital signal which was input from D-IN during RECPAUSE or REC-PLAY. (1) Other than audio signal (2) Other than signals of home-use appliances (3) Copy NG due to inversion of copy bit in CD. The digital signal which was input from D-IN during RECPAUSE, REC-PLAY or CD FUNC playback caused the following. (1) PLL of digital IN was unlocked. (2) Locking occurred in condition other than FS = 44.1 kHz There were no areas to record music or character infomation.(music name, disc name, etc.) during REC-PLAY. When an attempt to start is made, recordable area does not remain. ETNO > LTNO FTNO 0 or 1 UTOC recorded on disc could not be read. Start address > End address Any data of UTOC 0 to 4 looped. Nonaudio data was recorded in the track mode of currently selected TNO. Data "MINI" of system ID which has been written in TOC with ASCII code is not correct. The disc type written i TOC does not correcpond to pre/ mastered MD, recording MD and hybrid MD. Check whether CD is copy-inhibited one. (An exabple: CD-R)
Can't COPY
Din UNLOCK
TOC FULL
Replace the disc with a recording/ playback disc in which an area to register UTOC remains. UTOC data is not normal. Replace the disc with other disc. UTOC data is not normal. Replace the disc with other disc. UTOC data is not normal. Replace the disc with other disc. Select other TNO or replace the disc with other disc. The loaded disc is not applicable. Replace the disc, and check.
UTOC ERR R
When an attempt to set REC-PAUSE was made, there were no Replace the disc with other recording disc recordable areas. in which recording area remains. An attempt to set REC-PAUSE or to start editing was made on The loaded disc is a Playback-only disc. the playback-only disc. Replace the disc with a recording disc. An attempt to record or edit was made on the record/playback disc with its careless rease preventing tab being in rease preventing state. An attempt was made t oedit the track which was writeprotected by information written in UTOC. Specific editing conditions were not satisfied. Return the careless erase preventing tab to its initial position, and redo. The track on which an attempt to edit was made is a write-protected track. Redo on another track. The applied operation procedure is not proper. Redo, applying the ocrrect procedure. Check by troubleshooting. Check whether the ambient temperature is too high. Data of TOC or UTOC is not normal or disc las flaw. Replace the disc with other disc.
Can't EDIT
TEMP OVER
Owing to occurrence of some trouble internal temperature of set (MD unit) rose excessively.
DISC ERR RD PA WR
Read data was not correct or data could not be read correctly. Trouble occurred during recording if music data, resulting in record failure.
17
DM-3090
TROUBLE SHOOTING
Error display TOC ERR S TOC ERR R TOC ERR T Errors TOC was read but data was not correct. TOC could not be rad. Corrective action The TOC information recorded on disc does not conform to the MD standard. Replace the disc with other disc. The disc has flaw. Replace the disc with other disc. The disc has flaw. Replace the disc with other disc. Check that the disc is free from flaw, dust, fingerprint and black spot. Check for disc disalignment and run-out.
Trouble occurred during rewriting of UTOC, resulting in UTOC rewriting failure. After the disc was loaded, focusing failure occurred.
BLANK MD DEFECT
UTOC was read but total TNO and the number of characters of Perform recording to check that the disc NAME was 0? is recordable disc. Focusing error was caused by shock during REC-PLAY. Check that the disc is free from flaw, dust, fingerprint and black spot. Check for disc disalignment and run-out. Check that the record head contact is normal. Check that there is no broken wire between PWB and the recording head. Once reset, and redo. If error occurs persistently, replace EEPROM.
TOC W ERROR
MD ERROR
18
DM-3090
TROUBLE SHOOTING
When MD fails operate
If the objective lens of optical pickup is contaminated, MD may fail to operate. At first, clean the objective lens to check playback operation. If MD fails persistently to operate, perform checks as follows. If dust or foreign substance is accumulated on the pickup lens, playback is disturbed and indication of TOC (content of tracks) may be disabled. Before adjusting check that the lens is clean. If the lens is contaminated, treat it as follows. Turn off power supply, impregnate the lens cleaning paper with a small quantity of isopropyl alcohol, and gently wipe the lens with it with due care so that the lens is not damaged. At this time do not touch the lens directly with your finger.
Is power turned on when the remote control or main unit POWER button is pressed? Yes Is disc loading normal?
Yes
No
No
Is playback state set when the PLAY/PAUSE button is pressed? Yes Is audio output normal?
No
Is normal operation performed when the main unit POWER is pressed? No Is +5V applied to the pins 15 and 16 of CNS1902?
Yes
No Yes Is pulse given to the pin 5 of CNS1902? No Yes Is +3.2V applied to the pin 62 of IC1401? No Yes Is 8.4672 MHz pulse applied to the pin 15 of IC1401? Yes Is pulse output from the pin 34 of IC1401? Yes Check CNP471 and system PWB. No No
Check IC1201.
Check IC1401.
19
DM-3090
TROUBLE SHOOTING
Disc loading is not normal.
Is disc loaded when it is inserted? No Is the pin 4 of CNP1601 set to L state? No Yes Is change observed on the pin 23 or 24 of IC1601? No No Yes Is change observed on the pin 30 or 31 of IC1601? No Yes Check CNP1604 and CN1604 Check CNP1604 and IC1601. Check IC1401. Check CNP1601 and SW1956. Yes
Yes Is ejection performed when the MD taking-out button is pressed? Yes Disc retracts soon after completion of disc ejection. Yes Check CNP1601 and SW1956.
No
No Only the high reflection disc cannot be played back. Yes Is 1.02V0.3V (high reflection disc) applied to the pin 93 of IC1401 in the TEST mode where the high reflection disc has been inserted? No Yes
No Only the low reflection disc cannot be played back. Yes Is 3.2V0.3V(record enabied) or 2.06V 0.3V (record disabled) applied to the IC1401 pin 93 after the low reflection disc has been set?
No
20
DM-3090
TROUBLE SHOOTING
Normal playback
When it has been confirmed that EEPROM value is normal in the TEST mode Is initialization performed normally when high reflection disc is played back? No Check IC1201 Does disc rotate normally?
No
No
Is lead-in switch turned on in the TEST mode when the pickup is on the innermost periphery (Is the pin 6 of OC1401 on L level?) No
Yes
Check SW1953, mechanism switch PWB soldering joint, and CNP1601 pin 1 periphery.
Is an attempt to read repeatedly the TOC section of low reflection disc made? Yes
No
Since the TOC section has not been recorded on the new disc, replace it with recorded low reflection disc.
(Except DM-3090)
When sound is not output although the playback time display advances during playback in the normal mode. Is audio output waveform observed on the pins 24 to 26 of IC1701? Yes Is audio output waveform observed on the pins 22 and 24 of CNS1902? Yes Check connection between IC1701 and CNS1902. No Check the pins 70, 71, 72 and 74 of IC1201, and the pins 12, 16, 17, and 19 of IC1701.
No
21
DM-3090
TROUBLE SHOOTING
Record and playback operation
Insert the low reflection disc, and after verifying the audio output in the normal mode playback set the record/playback TEST mode Recording from start address cannot be performed. Yes No Check whether the disc is record-prohibited.
Is RF waveform output to the pin 1 IC1201 or TP1274 when playback is performed after recording? No Does the level of pins 3 and 26,39 of IC1401 and the pins 9 and 19 of CNS1101 in record state differ from that in playback state? Yes Does RF pattern appear on the pin 50 of IC1201? Yes Check the IC1251, Q1251 to 1254 and CNS1252.
Yes
(Except MD-3090 below this item) Is input waveform given to the pins 18 and 20 of CNS1902 in AUX input record in the NORMAl mode? Yes Is input waveform given to the pins 3 to 5 of IC1701? No Yes Check the periphery of IC1701, check the pins 70, 71, 72, and 73 of IC1201. Check connection between IC1701 and CNS1902. Check the main PWB. No
No
No
No
No
22
DM-3090
TROUBLE SHOOTING
Disc motor fails to run
Does waveform appear on the pins 24 and 25 of IC1201 in the TEST mode focus gain coarse adjustment step? Yes Does waveform appear on the pins 34 and 35 of IC1601, pins 1 and 2 of CNP1603? Yes Replace the completed disc motor. Check soldering joint of PWB of completed IC1601 and CNP1601 disc motor. No Check soldering joint and parts of pins 24 and 25 of IC1201, and peripheral circuit.
No
No
Yes Is there any change on the pins 28 and 29 of IC1601, and the pins 1 and 2 of CNP1602 when the or button is pressed? Yes Does voltage on the positive and negative terminals of slide motor change when the or button is pressed? Yes Replace the slide motor. Check the soldering joint connected to the slide motor to see whether there is wire breakage. Check the soldering joint of IC1601 and CNP1602.
No
No
23
DM-3090
ADJUSTMENT
MD SECTION
1. Preparation for adjustment
Test disc Type 1 2 3 Test disc High reflection disc TGYS1 (SONY) Low reflection disc Recording minidisc Head Adjusting transparent
2. Test mode
Test mode setting method (PLAY/PAUSE) button, press the RESET button. 1. Holding down the ENTER button and After 3sec, take your hand off the RESET button first. (State A is changed to state B .) 2. Insert the playback disc 1 (high reflection disc) or recording disc 2 (low reflection disc). (During disc loading : display LOADING) (State C is set.) Thus, the test mode state is set. A tsm e : TEST MODE represents version of MD microcomputer. TEST STOP state (When the (STOP) button is ressed in the C state, the indication A is restored. To restore C again, press the ENTER button.) B EJECT TEST C AUTO TEST Entering the specific mode Whenever the ENTER button is pressed, the mode is changed. AUTO pre-adjustment AUTO adjustment RESULT SUB EEPROM setting MANUAL adjustment
RESULT
MANUAL pre-adjustment
Canceling the test mode When the POWER button is pressed, the test mode is canceled, and the POWER OFF state is set.
Test Mode
1. AUTO pre-adjustment mode 2. AUTO adjustment mode Automatic pre-adjustment is performed. (After adjustment the grating adjustment mode is set.) The adjustment value is output with the aid of system controller interface. Automatic adjustment is performed. The adjustment value is output with the aid of system controller interface. Continuous playback is performed. (Error rate indication, jump test) The measurement value, set value and calculated value are indicated. The set value is changed manually (in servo OFF state). The set value (after calculation) is indicated. The set value is changed manually (in servo OFF state). RF side manual adjustment is performed. Focus and tracking signal ATT manual adjustment is performed. Focus and tracking signal offset setting is performed. Focus and tracking signal ATT manual adjustment is performed. This mode does not use on the occasion of service. Continuous playback from the specified address is performed. C1 error rate measurement, ADIP error rate measurement. Continuous recording from the specified address is performed. Change of record laser output (servo gain is also changed according to laser output) TEMP setting (of EEPROM setting) CONTROL setting (of EEPROM setting) Setting of laser power (record/playback power)
6. MANUAL adjustment mode 7. EEPROM setting mode 8. TEST-PLAY mode 9. TEST-REC mode 10. EJECT mode
24
DM-3090
ADJUSTMENT
1. AUTO pre-adjustment mode (Low reflection disc only)
Step No. Step 1 Step 2 Step 3 Setting Method Testmode STOP state Press once the ENTER button. AUTO pre-adjustment menu Press once the MD PLAY button. The slide moves to the innermost periphery, and automatic pre-adjustment is started. During automatic adjustment changes as follows. HAoRFgSAgSBgPTGPCHGTGGCHRCG SEGRFGSAGHAOHEOTCOLAO End of adjustment If adjustment is OK, Step 4. If adjustment is NG, Step 5. Grating adjustment, adjustment value output Press once the MD STOP button. STEP 2 Adjustment value output Press once the MD STOP button. STEP 2 AUTO pre-adjustment menu Remarks [tsm [ [ Display e ] ] A U T O
:______]
Step 4
[_COMPLETE_]
Step 5
[ AUTO ]
: Adjustment name,
: Address
Step 4
[_COMPLETE_]
[ Can't _ ADJ. ]
: Adjustment name,
: Measurement value,
: Address
25
DM-3090
ADJUSTMENT
3. RESULT sub-mode
Step No. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Step 16 Step 17 Step 18 Step 19 Step 20 Step 21 Step 22 Step 23 Step 24 Step 25 Setting Method Testmode STOP state Press the ENTER button three times. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. RESULT sub-menu Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of measurement value Indication of adjustment error sequence No. Indication of adjustment status Indication of pre-adjustment not completed (00)/completed (4B) Press once the MD PLAY button. Indication of measurement value Remarks [tsm [RFG:_ [RCG:_ Display e __ __ ] ] ] ] ] ] ] ] ] ] ] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] _ _ _] [_RST_YOBI_]
[RTG:__ _ _ _ [GTG:__ _ _ _ [PCH:__ _ _ [GCH:__ _ _ [SAG:__ _ [SBG:__ _ [SEG:__ _ [SFG:__ _ [HAO: [HBO: [HEO: [HFO: [LAO: [LBO: [LEO: [LFO: [TCO:_ [YOB:_ [D I F:_ [ADJ:_
[_RST_YOBI_]
: Measurement value, : Adjustment value, : Other various informations ressing the REC button causes reversing. When the jog key is turned upward while the setting is displayed, the setting increases, and a new setting is stored in RAM. When the jog key is turned downward while the setting is displayed, the setting increases, and a new setting is stored in RAM.
[_RESULT___]
: Measurement value ressing the REC button causes reversing. When the jog key is turned upward while the setting is displayed, the setting increases, and a new setting is stored in RAM. When the jog key is turned downward while the setting is displayed, the setting increases, and a new setting is stored in RAM.
26
DM-3090
ADJUSTMENT
5. MANUAL auxiliary adjustment mode (only low reflection disc)
Step No. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Step 16 Step 17 Step 18 Step 19 Step 20 Step 21 Step 22 Step 23 Step 24 Step 25 Step 26 Step 27 Step 28 Step 29 Step 30 Step 31 Setting Method Testmode STOP state Press the ENTER button five times. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. MANUAL auxiliary adjustment mode Offset "0" setting A signal offset tentative measurement B signal offset tentative measurement E signal offset tentative measurement F signal offset tentative measurement Offset tentative measurement Laser ON Innermost periphery move RF side FG rough adjustment Focus ATT (A signal) tentative setting Focus ATT (B signal) tentative setting RF side pit section TG adjustment Pit section COUT level setting Outer periphery move RF side groove TG adjustment Groove section COUT level setting RF side TCRS adjustment Tracking ATT (A signal) setting Tracking ATT (B signal) setting Indication of tracking EFMIO measurement RF side pit section FG adjustment Focus ATT (A signal) setting Focus ATT (B signal) setting Offset "0" setting A signal offset measurement B signal offset measurement E signal offset measurement F signal offset measurement TCRS signal offset measurement A signal offset measurement B signal offset measurement E signal offset measurement F signal offset measurement Press once the MD PLAY button. Initial setting Temperature measuring mode Remarks [tsm [TMP:_ [HAo: [HBo: [HEo: [HFo: [RFg: [SAg: [SBg: [PTG: [PCH: [GTG: [GCH: [RCG: [SEG: [SFG: [gMI: [R F G : [SAG: [SBG: [HAO: [HBO: [HEO: [HFO: [TCO: [LAO: [LBO: [LEO: [LFO: ___] __ ] ] ] ___] ___] ___] ___] ___] ___] ___] ___] ___] __ _ __ _ __ ] ] Display e ] [_MNU_YOBI_] ___] ___] ___] ___] ___] __ ] ] ] ] ] ] ] ]
[LON:______]
: Measurement value, : Set value, : Account value If the jog key upward/downward is pressed during setting indication, the setting increases/decreases, and the new setting is stored in RAM. If the REC button is pressed, the setting returns step by step excepting the following case. A signal offset (HAO) Offset tentative setting RF side FG adjustment (RFG) RF side TCRS adjustment (RCG) RF side groove TG adjustment (GTG) RF side groove TG adjustment (GTG) Innermost periphery move RF side pit section adjustment (PTG) RF side pit TG adjustment (PTG) RF side FG rough adjustment (RFg) Laser lighting (LON) Laser lighting (LON) Offset "0" setting A signal offset tentative measurement (HAo) If the measurement value is within the OK range, " " appears on the 8th character.
If the MD STOP button is pressed while the MANUAL adjustment menu is displayed, the state is changed to the TEST mode STOP state. If the REC button is pressed, the setting returns step.
27
DM-3090
ADJUSTMENT
7. High reflection disc
Step No. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Setting Method Testmode STOP state Press the ENTER button six times. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. Press once the ENTER button. MANUAL adjustment menu Laser ON Innermost periphery move Tracking ATT (E signal) setting Tracking ATT (F signal) setting Indication of tracking EFMIO measurement (pit section) Focus ATT (A signal) setting Focus ATT (B signal) setting Outside periphery move Track closs setting Tracking ATT (E signal) setting Tracking ATT (F signal) setting Indication of tracking EFMIO measurement (groove section) Focus ATT (A signal) setting Focus ATT (B signal) setting Press once the MD PLAY button. Initial setting Temperature measuring mode Remarks [tsm [TMP:_ [PEG: [PFG: [PMI: [LAg: [LBg: [GCG: [GEG: [PFG: [GMI: [LAG: [LBG: ___] ] ] ___] ] ] ] ] ] Display e ] [_MNU_AJST_] ___] ] ] [LON:______]
If the MD STOP button is pressed while the MANUAL adjustment menu is displayed, the state is changed to the TEST mode STOP state. If the REC button is pressed, the setting returns step by step excepting the following case. Track closs ATT setting (GTG) Innermost periphery move Focus ATT (B signal) setting (LBg)
8. TEST-PLAY mode
Step No. Step 1 Step 2 Step 3 Setting Method Testmode STOP state Press the TIMER/DELETE button. TEST-PLAY menu Press once the DISPLAY/ ADRES setting (Target address initial value is indicated) CHARAC button. During search the search output pin 11 is set to "H", and it is Press once the MD PLAY button. returned to "L" when continuous playback is started. Continuous playback (pit section) (Address + C1 error indication) Continuous playback (groove section) (Address + C1 error indication) Press once the DISPLAY button. (Address + ADIP error indication) Press once the MD STOP button. TEST-PLAY menu Remarks [tsm Display e ] [TEST_PLAY_] [ADRES_0050]
[s [a [a
c c a
] ] ]
[TEST_PLAY_]
If the MD STOP button is pressed while the TEST-PLAY menu is displayed, TEST mode STOP state is set. If the MD PLAY button is pressed while the TEST-PLAY menu is displayed, continuous playback is started from the current pickup position. Whenever the TIMER/DELETE button is pressed in the address setting mode, the address changes as follows. 0 0 5 0 0 3 0 0 7 0 0 0 8 A 0 0 0 5 0 / + changes Whenever the TIMER/DELETE button is pressed in the address setting mode, the digit which is changed with as follows. 0 0 5 0 0 0 5 0 0 0 5 0 0 0 5 0 / + and DISPLAY/CHARACTER button in the address setting mode is set to +01H/ The digit of address which has been specified with -01H. * If the / + button is held down, the setting changes continuously with 100 ms cycle. If the TRACK EDIT button is pressed in the continuous playback mode, the number of jump lines changes as follows. 1 line 10 line 400 line 1 line TR_JUMP] * After the number of jump lines is indicated for one second, the address indication is restored. [ / + button is pressed in the continuous playback mode, the specified number of lines is jumped in the FWD/REV If the direction. * If the / + button is held down, the setting changes with 100 ms cycle. Whenever the CD STOP button is pressed in the continuous playback mode, the indication changes as follows. * Pit section Continuous playback (SUBQ address indication + C1 error indication) remains. * Groove section Continuous playback (ADIP address indication + C1 error indication) remains. Continuous playback (ADIP address indication + ADIP error indication) remains. Continuous playback (ADIP address indication + C1 error indication) remains.
28
: Adress,
: Error late,
: Jump lines
DM-3090
ADJUSTMENT
9. TEST-REC mode
Step No. Step 1 Step 2 Step 3 Step 4 Setting Method Testmode STOP state Press the TIMER/DELETE button. TEST-REC menu Press once the DISPLAY/ CHARAC button. ADRES setting (indication of address initial value) Remarks [tsm Display e ] ] [TEST_REC__] [a0050_pw
Press once the MD PLAY button. During search the search output pin 11 is set to "H", and it is (returned on "L" when continuous playback is started.Address + C1 error indication) Continuous recording Press once the MD STOP button. TEST-REC menu
[a
pw
Step 5
[TEST_REC__]
If the MD STOP button is pressed while the TEST-PLAY menu is displayed, TEST mode STOP state is set. If the MD PLAY button is pressed while the TEST-REC menu is displayed, continuous record is started from the current pickup position. Whenever the TIMER/DELETE button is pressed in the address setting mode, the address changes as follows. 0 0 5 0 0 3 C 0 0 7 0 0 0 8 A 0 0 0 5 0 Whenever the DISPLAY/CHARACTER button is pressed in the address setting mode, the digit which is changed with / + changes as follows. 0 0 5 0 0 0 5 0 0 0 5 0 0 0 5 0 The digit of address which has been specified with / + and DISPLAY/CHARACTER button in the address setting mode is set to +01H/ -01H. * If the / + button is held down, the setting changes continuously with 100 ms cycle. If the JOG button is pressed in TEST-REC mode and continuous record mode, the laser record power changes. (Servo gain changes also according to the record power.) : Adress, : Laser power cord
Press the NAME/TOC EDIT button. CONTROL setting of EEPROM setting (Refer to CONTROL setting of EEPROM)
29
DM-3090
ADJUSTMENT
Mechanism Adjustment 1. Optical pickup grating inspecting method
OSILLOSCOPE
100K 470p
GND CH1 CH2
1 3 2
Spindle Motor
Figure 23-1 Optical Pickup Grating Deviation Measuring Method After the automatic adjustment is performed in the AUTO mode (test mode) with the aid of high refection MD disc ("COMPLATE" is displayed), the Lissajous's waveform (x-y) is adjusted. 1. Slightly loosen the 3 screws of spindle moto, and maken an adjustment, observing the Lissajous's waveform. 2. After adjustment tighten the screw in arder of 1 , 2 , 3 .
Adjusting hole
3
Spindle motor
1
adjusting hole
Check the Lissajou's waveform, shifting the mounting position with a screwdriver (to be fitted into the disc motor adjusting hole).
Figure 23-2
Figure 23-3 Jitter connection diagram After performing automatic adjustment in AUTO mode of TEST mode using the low reflection MD disc, check this jitter in pit continuous playback and groove continuous playback mode.
5P extension flat cable
2P extension connector
28Pextension flat cable MD Main PWB 6P-2P extension connector Extension PWB for service Fit the extension PWB for service to the mechanism
Figure 23-4
30
DM-3090
PARTS DESCRIPTIONS
31
R1707
2
R1807
R1734
C1460
IC1251 8 J1921 14
Q1804
C1810
C1927
C1709
C1716
D1251
IC1916 C1958 16
R1964
28 C1711
15 25 20 R1717 10 Q1701 14 R1714 C1700 L1701 C1717 R1715 C1702 R1702 L1702 C1720 IC1202 IC1906 20 16 15 11 1 C1954 C1951 C1964 1 7 1 28 1 7
R1965
R1701
R1971
CN1602
1 R1255 R1269 2
6 R1471
10 R1409
R1221
L1203 C1210
C1206
R1963
R1266 50 R1263 C1610 55 R1261 C1203 60 R1202 IC1201 65 10 20 R1262 R1613 R1614 51 45 40 35 30 26 25
R1610
C1604
C1211
Q1601
15
XL1201
R1201
R1611
C1424
C1204
C1207
75
85
90
1 100 C1202
1 CN1603 2
6
R1668 L1601 L1201
L1102 R1100
R1107
CN1101
JC170
JC171
C1803
TP1518 TP1516 TP1504JC121 R1947 TP1522 TP1520 TP1519 TP1502 TP1512 TP1503 TP1517 JC196 TP1521 TP1501 R1805 Q1807 IC1801 R1804 3 4
PICK UP
+
CD MOTOR PWB-F
TP1523
1 C1805
R1820
R1821
SW702
TP1511
CNP3
TP1801
Q1801
PICK UP IN
5 TP1910
6 5 4 3 2 1
CD SUB PWB
CNS3
8 7 6 5 4 3 2 1
R1973
TP1505
4 TP1904
COL OR TABL E BR BR OWN R ED O RANGE YELLO W G REEN BLU E VIO LET G REY WH ITE BLACK PIN K
TP1509 TP1507 C1715 C1713 TP1508 R1424 TP1803 TP1713 TP1510 TP1506
CNS1
R1974 TP1911
CD SUB PWB
CNS2
CD SUB PWB
RD( R) OR YL GR BL
C1402
TP1278 C1710 C1707 C1706 80 C1703 TP1710 R1478 C1712 R1418 TP1701 TP1712 TP1416 81
TP1457
C1957
SW701 OPEN/CLOSE
VL GY WH(W) BK PK
C1423
TP1119
CNS10
C1956
BR RD OR YL GR 1 2 3 4 5
CD SUB PWB
R1473 TP1711 TP1990 C1743 TP1702 TP1414 1 TP1415 C1406 4 R1476 R1475 65 IC1401 15
C1401
IC1802 R1716
TP1413
70
10
R1406
C1714
CN1601
R1415
R1426
4
TP1603
R1427 R1425
TP1601
C1405
IC1402
60
20
TP1454
25 55
C1421 C1422
5 4 3 2 1
R1428
CN1601
TP1607
TP1602 TP1604
45 50
40
35 30 31 TP1458 C1121 TP1122 L1101 TP1150 TP1107 TP1105 TP1108 TP1109 C1109 C1106 TP1210 C1107 TP1142 TP1112 TP1141 TP1116 C1110 C1111
RECORD HEAD
MD MAIN PWB
R1407
MD MAIN PWB MD MAIN PWB MD MAIN PWB
TP1213
RD 1 BK 2
CN1602
RD 1 BK 2
CN1603
RD 1 BK 2
CN1604
C1656
C1652
TP1609
C1605
R1651
C1657
R1656
R1664
C1653
TP1616
R1662
TP1605
42 40
R1665
R1653
TP1608
PICK UP
SW1953 READ IN
R1281
C1102
TP1275
15
TP1140 37 36 40 TP1138 35 TP1220 TP1204 C1115 R1102 TP1137 R1153 R1154 TP1136 30 IC1101 TP1274 TP1135 TP1106 C1114 R1152 TP1134 R1150
R1155
TP1139
48 TP1113 45 5 10 1
FLAT CABLE
C1103
CN1601
R1904 CN1901
20 22 21 TP1102 TP1104
R1650
C1650
25
TP1118 C1104
25 24 TP1127
20
15
C1661 C1631
TP1103 TP1101
TP1612
TP1128
TP1132 C1112
TP1130 TP1131
C1105
SW1954 PLAY
CN1101
MD MAIN PWB
MD MAIN PWB
VL VL
1 2
CN1252
33
34
35
36
Refer to the schematic diagram for the value of resistors and capacitors.
C1254
R1223
+B
IC1101 IC1201 IC1202 IC1251 IC1401 IC1402 IC1601 IC1801 IC1906 IC1907 IC1916 IC1990 Q1251,1252 Q1253,1254 Q1401,1403 Q1402,1404 Q1451,1821,1822
: IR3R55 : LR37648 : IX2474 : TC74ACT02F : IX0227AW : S29294A : M68758FP : XC82EP32 : TC7ST08F : TC9246F : 74VHC08F : 74AC04FS : : : : : 2SK2909 2SK1473 RN2404 RNC1404 RNC1407
CW1901
LEAD IN HINF GND LOADING MINF L1251 47uH +B +B +B +B +B +B +B +B +B +B
LEAD IN
HEAD DRIVER
4.9V
IC1251
+B
( ( ( ( ( ( ( ( (
+B
( ( ( ( ( ( ( (
+B
+B
Q1252
4.7 45 46 47 48 49 50 51 52 53 54 80 18 15 29 19
)
+B
3.2V
44
R1211
R1210
220
D1252
100
99
87
98
86
97
85
96
84
95
83
94
82
93
81
92
80
91
79
90
78
89
88
77
C1252
120P
SYRDX
SYWRX
DINTX
SYD7
MCCK
SYD6
COUT
SYD5
SENSE
SYD4
FOK
SYD3
SFSY
SBSY
SYD2
SYD1
SBO
SBCK
SYD0
TEMON
RSTX
DGND
SYRS
VDD1
TOTMON
D1251,1252 D1990
: SB80209CP : 1SS372
LOADING
SW1955 MO159 2 2
R1251
VCC
0.027
76
REC HEAD
+B
+B
CW1903
C1251 1 1
C1208 0.047
C1209 1
14
13
12
11
10
100
40
)
) )
Q1251
10 GND +B
1 FEMMON
DIGITAL OUT
74
CN1252 D1251
SW1956 MO156 2 3 4 5 6 1 7
+B C1202 1
AVCC
0.9V
72 71 70
( )
1.6V
3 EFMI 4 AGND
RC120 0
( )
71 BCLK 70 LRCK
Q1253
( 5 )
5 AIN 6 EIN 7 TCG 8 9 FIN 10 VBAT 11 WBI 12 VDD1 BIN VDD3 DOUT 67 DGND C1207 69
Q1254
R1252 R1253
+B
+B
3.2V
+B LINE
3.2V
+B
( 6 ) ( 7 ) ( 8 )
PICKUP
68
R1281 +B 47 R1255 0
( 9 )
+B R1254 220
3
28 27 26
( 4 ) ( 3 )
CN1101
SW +2.8V B LVVOUT 25 24 APCOUT 25 24 R1107 1 23 22 21 R1106 20 LDVAR A COM RF1 16 15 14 I/V 13 I/V 12 11 10 9 I/V 8 7 APCIN DGND LVVIN FT+ F+ TVCC AGND MP/R RF2 8 7 6 390K 5
( 9 )
3.2V
+B
+B
( 11 )
1.6V
1.6V 0V
66 DIN 65 R1202
+B C1211 C1109
3300P
0.47
C1107
C1108
4700P
IC1101
RF AMP
+B C1101 1
0.47
14 15
1 VCC 2 GND
8 23 22 7 21 6 20
16 +B
1M XL 1201
13
XO
XI DGND VDD1
64 63 62
1.6V
1.6V
1.6V
0.0V
1.6V
48
47
46
45
44
43
42
41
40
39
1.6V
38
1.6V
37
0.8V
+B
+B 61 60 59
1.6V
R1653
( 18 )
17
ATTR
EFMAGC
GOUT
EFMAGI
AGND
EFMO
RF2-1
POUT
AVCC EFMI
ADAGI
ADAGC
+B
1.4V
18
72 3
( 3 ) ( 4 )
19 4 5 18 17
19 18 17 16 9
( )
+B
I/V
0.8V
( 10 )
RF1 R and SW
( 21 )
1.6V
21
+B
15 14
12 11
R1155
56K
RF3 13 RF4 12 1 11 10 9 39
( )
C1102
1.6V
REFI
ADIP AGC
ADIPO NC ADLPFO
35 34 33 32 31 30 29
1.6V
+B
RAOEX
DGND
RAWEX
RAA10
( 25 )
RACASX
ACRCER
RARASX
1.3V
TCRS
RAD2
RAD3
RAD1
RAD0
1.6V
1.6V
26
27
28
40
29
41
30
42
RAA9
31
43
32
44
33
45
34
46
PLCK
62K
35
47
36
48
37
38
0.7V
RFADD
+B
11 7
C1210
( 37 )
( 39 )
( 40 )
( 32 )
( 33 )
( 34 )
( 35 )
( 26 )
( 27 )
( 28 )
5 F.COIL 4 3 2 T.COIL 1
4 3 2 1
13 9 12 8
22K
( 10 )
C1115
( ( ( (
+B
26
27
28
C1206
10
( 11 )
+B
22K
( 12 )
I/02
VCC
RAS
DTEMP
CLOCK
LATCH
SGAIN
DGND
AGND
DVCC
AVCC
DATA
STBY
GND
CAS
22K LOGIC
11 4 I/03 I/04 OE A4 A5 A6 A7 A8 5 10 9 6 +B
1.5V
+B
1.6V
12
FIN
FOUT
25
1.9V
R1150
I/01
A3
A2
A1
A0
A9
WE
CN1602
1 SLD+ SLD1 2
( 29 ) ( 28 )
DISC
11
12
13
15
16
18
14
17
19
13
14
15
16
17
18
19
20
21
22
23
2.3V
0.8V
2.5V
1.3V
1.3V
1.7V
2.5V
1.2V
1.2V
FM
24
( 37 )
( 39 )
( 40 )
( 32 )
( 33 )
( 34 )
( 35 )
( 36 )
( 41 )
0V
0V
1.4V
3.2V
20
+B
C1105
( 92 ) ( 32 ) ( 33 ) ( 31 )
+B
+B
+B
1 +B
C1121
DM DISC MOTOR
+B
3.2V
+B
L1102 0.47uH
CN1604
1 TRY+ 1 C1609 1
( 31 )
+B
+B
+B
+B
+B
+B
+B
LM LOADING MOTOR
TRY-
( 30 )
L1201 0.47uH
1.6V
11
EIN
EOUT
26
1.9V
R1151
270P
+B
0.8V
0.8V
2.2V
2.0V
3.0V
1.2V
1.2V
2 3 12
0.1
13
C1992
22K
C1114
1.6V
10
BIN
BOUT
27
1.3V
R1152
270P
29
1.6V
AIN
AOUT
28
1.3V
R1153
270P
( 29 )
IC1990
3.2V
1 VCC 14
) ) ) )
+B
22K
C1116
( 36 )
( 41 )
1.6V
TCGI
TCCO
1.6V
R1154
BIAS
WBO
1.6V
R1102 560
39
49
50
EFMO
0V
R1221 220
1.6V
+B
TRDRR
TEST4 55
0.8V
RF4
DIFF
ADIPI
36
1.6V
( 22 )
1.7V
22
SLDRF
TEST3 TESO1 54 53 52
1.6V 1.6V
R1269 0
0.8V
RF3
1.6V
R1665
23 SLDRR 24 SPDRF
DIFF
( 24 )
2.0V
62K R1663
51
+B
10K
100K R1651
( 19 )
1.9V
19 FODRR 20
0.7V
RF2
EFM AGC
100K R1657
( 20 )
1.7V
TRDRF
120K R1655
CDDATA
+B
EFM OUT
IC1201
R1201 150
C1204
IC1202
4M BIT D-RAM
7 GND 1 8 C1990
INVERTER
+B +B
DIGITAL LINE
3.2V
1.0V
+B
DIGITAL REC
DIGITAL IN
D1990
+B
4.3V
LOADING
DIGOUT
DIGIN
LEAD IN
GND
GND
GND
MINF
HINF
CN1904
4 3 2 1 1 2 3 4 5
CN1601
C1421
C1422
0.022
0.022
+B +B
+B +B
+B +B
+B +B
+B +B
+B +B
+B +B
+B
+B
+B +B
R1429 10K
R1430 10K
R1422 10K
R1423 10K
+B
+B
R1472
R1424 10K
R1973 6.8K
R1974
R1927 22
C1913
R1614 18K
R1431 0
220
3.2V
3.2V
1.9V
3.2V
3.2V
2.2V
1.4V
1.7V
1.6V
1.6V
3.2V
3.2V
3.2V
3.2V
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
14
DOUTMT
AVCC
HINF
VREF
GND
TESTK2
MINF
TESTK1
DTEMP
AVCK1
AVCK2
AVCK3
TEST0
TEST1
MUTE
DAMUT
1.6V
+B
1 2
C1927
12
( 72 )
+B 12
0.047
13 J1922 0
1 2
( 3 )
ADMUT
TEST2
EMPH
VCC
+B
3.2V
( )
81
80 XRST 79
3.2V
R1418 47K
0.9V
1.6V
3 4 11 10 +B 9 6 7 GND 8
0.2V
3 LDVAR 4 ADJS 5
DIGITAL OUT
3.2V 0V
3.2V 2.3V
+B
+B
0.9V
R1420 1K C1423 0.022
0V 3.2V
0V
6 LOAD IN
0V
1.6V
C1402
3.1V
A/B
73
3.2V
R1477 10K
+B
IC1916
SELECTOR
+B +B
0.047
72
3.1V
R1406 3.3K 12
( )
3.2V
C1401 0.047
12
IC1401
MD-MECHA u-COM
L3CLK
68 67 66 L3MODE +B +B +B
+B
+B
+B +B
( 15 )
1.6V
+B
15 16
MCCK VCC
+B +B +B
3.2V
+B +B
+B
+B C1951 0.047
R1415 1K
( 18 )
17
5.1V 4.4V
3.1V 0V 0V
18 19 20
Q1601
+B C1610 10
30K
+B
C1412
680P
+B
12K
+B
+B
GND
+B
2.8V
23 FSW
59 58
0V
R1407
24 25
57 56
( 80 )
R1612
3.2V
C1403 J1405 680P 10K
IC1907
+B 1
CLOCK GENERATOR
16
3.3K
56K
3.2V
26 SYSD0 HDON SYSD1 LD+ SYSD2 LD4M/16M CLOCK KDATA SYSD7 SYSD6 SYSD5 LATCH SYSD4 CIN DATA MDDATA 29 DSTB SYSD3 SYWR DSCK SYRD SYRS FOK R/P 30 INNER
55
( )
54 53 52 51
+B
+B
DETECTOR
PEF
R1967
( 27 ) ( 28 )
+B
0V 0V
27 28
53 52 51
47
COMPARATOR
C1807 220u4
C1806
+B
10
VAR
15 R1413 3.3K
R1409 1K
( 29 )
3.2V
C1424 0.022
R1654
6.8K C1652
( 8 ) ( 9 ) ( 12 ) ( 13 )
S2
S1
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
+B
31
50
+B
3.2V
+B
VDDA 4
42
+B
0V
0V
0V
R1471
0V
0V
2.6V
R1961 100
COUNTER
10K
+B
( 42 )
( 34 )
( 35 )
( 36 )
( 31 )
( 32 )
C1953 0.47
+B
43
+B
C1952
( 44 )
( 45 )
( 46 )
( 47 )
( 48 )
( 49 )
VCO
I/F
5.0V 3.2V
12 +B
+B
4.9V
( 40 )
( 50 )
0.01
1.5V
Q1403
R1968 220 R1412 100K
C1805
C1991
5
( (
58
10
0.047 10
2.4V
60
Q1401 Q1402
IC1402
0.4V
5 DI SE CS
EE-PROM
+B 61 59
( )
4.9V
R1414
4 3
3.2V 3.2V
R1473 100K
C1651
10K
R1416 10K
VSS
C1407 0.022
C1145 0.033
SELECTOR
0.4V
9 +B
( 19 )
C1405 0.1
C1650
0V
+B
+B
+B
( 39 )
+B
+B
+B
+B
+B
+B
( 22 )
10K
3.2V
+B
3.2V
( 18 )
10K
Q1404
13
0V
( 92 )
( 33 )
( 37 )
( 43 )
3.4V
+B
14
3.3V
+B
3.3V
3.2V
IC1801
C1601 1
2 +B +B +B
4.4V
820P
2.6V
3.1V
C1964 1000P
R1965 10K
5.0V
58
1.0V
( 22 )
3.1V
22 MDRSW
EEPD 59 R1474 1K
60
R1611
AND GATE
( 21 )
0V
21 SERCH
60
R1475 1K
+B
EEPK
61
47K
IC1906
61
R1617
VCC
( 19 )
VCC
+B R1476 1K
R1610
C1604
( ( )
5.5V 1
3.2V
62
+B
+B +
5.1V 4.4V
R1609 1.5K R1656 6.8K C1653 820P
( 20 )
3.2V
Q1820
+B
3.2V AVR
54
3.9V
Q1807
+B + R1821 1
5.1V
R1820 +B 1
( 21 )
W
MAIN -CNW301 2/2 CN1902
J1730 0 R1733 1K 24 R1758 1K 23 R1759 1K 22 R1953 47
( 74 )
21 R1951 0 R1994 20 R1952 47 47 19 R1940 220 R1995 0 18 J1950 0 LR190 22 17 R1708 6.8K C1724 22P C1917 68P JC171 22P JC196 22P
( 71 ) ( 70 ) ( 12 )
( 72 )
SYSCLK
J1720 0
J1963 0
Q1801
+B 2.2 C1802 100u10 R1801 1.8K R1804 220K C1803 C1801 2.2 +
16 L1950 15 1uH 14 13 12
+B
R1805
100K
R1802
270
11
D.GND
R1827 270
R1466
( 34 )
B
10 DSTB 9 MODATA
Q1821
Q1803
Q1802
( 35 )
220 R1462 8 KDATA 6.8K R1460 7 SERCH 6.8K R1458 6 6.8K R1454 DSCK
R1461 10K
( 21 )
R1459
Q1822
10K
( 37 )
( 5 )
5 C1425 0.047 1K
MD-ST
( 12 )
Q1451
R1452 4 3.3K R1456 RESET
( 6 )
3 1K +B R1939 2 1 1K
R1947 +B +B +B 47
( 1 )
+B
+B L1601 1uH
+B
+B
C1661 100u10
IC1601
1.2V
REG+
CH3IN OUT3 +
42 41
1.7V 1.7V
C1656
5.1V
3.7V
REGB
25
4 +B 5
39 38 +B 24 36 35 C1602 1
( ) ( )
37
1.6V
C1657 5600P R1664
NC VM3-
35
2.1V
1.6V
OUT1 34 33
( )
34
2.9V
32 VM4+ 31
10K
1.6V
31
30
2.4V
12
29
2.6V 1.6V
13 14
VM5-
28
2.5V
1.6V
C1654 0.015 R1658 15K
15 16 17
23 22
(
28
22K C1655 R1669 0.015 R1660 C1631 1 21 OUT4 22 R1668 6.8K 15K
1.6V
1.6V
6.8K
1.6V
20
IN4-
23
1.2V
22K R1666
1.2V
R1667 27
1.6V
1.6V
VM5+
29
2.6V
VM4-
30
2.5V
2.6V
1.6V
IN1+
1.25V
IN3-
40
1.6V
+B
R1620
CAUTION: For continued safety, replace safety critical components only with manufacturer's recommended parts (refer to parts list). indicates safety critical components. For continued protection against risk of fire, replace only with same type and rating fuse(s). To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer. The DC voltage is an actual reading measured with a high impedance type voltmeter. The measurement value may vary depending on the measuring instruments used or on the product. Refer to the voltage during RECORDABLE MD PLAY unless otherwise specified; The value shown in ( ) is the voltage measured at the moment of STOP. The voltage followed by (REC) refers to the value during MD RECORDING.
DM-3090 (1/2)
DM-3090
Y22-7510-00
7 2
MM: 2.5mV
6
(AUDIO)
LINE REC IN
MD-UNIT -CN1902
MD-UNIT -CN1904
B
Lch 1 Rch 2 J101A J301
C310 0.022
1/2 D301
R103 1K
1/2
C102 0.022
MAIN SECTION
3 R301 82
R104 1K
R307 22 C313 0.022 C119 0.022 R108 47K C106 L101 0.22uH 220P C108 Iu50 C107 Iu50 + + R107 100K 220P C105 +5V C303 0.022 C302 0.022 R105 47K
R309 10K
1 REC IN
+5V +5V C301 0.01
L302
+5V
+5V
10uH
C304
0.022
RX302
5.1V
8
R109 1K
7 6
R302 330
( 16 )
BCK L3MODE 13 12
( ( )
L3CLK 13
)
14
R407
560
3.0V 0.2V
R410 220K R405 330
R411 4.7K
220K
R403
( 17 )
1.6V
17 WS SYSYCLK 12
R408 220K 18 DATA0 VSSD 11 R406 560 R401 19 DATAI VDDD TEAT3 OVERFL TEST2 TEST1 VADCP + VADCN 6 7 8 9 L201 10uH 10 +BV 560 20 21 220K C470 100P R404
560
MUTE
R553 68K
0.9V 0V
DFS0
R552 39K
DFS1
1.0V 3.3V
C201 100u10
DADATA
AC
R116 100
BLCK
16
LRCLK
17
ADDATA
3.3V 0V
C207 100u10
IC201
DIGITAL OUT
12
R409 220K
16
D 7.5/5V
+7.5V
D 7.5/5V
+7.5V
+7.5V
3.3V
23
0V
C531 0.1
D.GND
1.7V
D,GND
R554 68K
3.3V
25
DSTB
10
0V
C203 47u10 +
MD DATA
K DATA
1.6V
28 VREFD
3.3V 0V
+BV C206 + 1u50
+7.5V
AD
1M
DSCK
-7V
MD-ST
17
10
19
20
AA
0V
10 11
R114 1K R113 1K
5.1V
R112 1.5K C114 47P C113 47P R111 1.5K
R305 56K
R304 2.7K
R303 220K
C305 0.022
3.9V
2.5V
5.1V
2.7V
2.7V
5.2V
12 3 6 5 2 + + 3 7 6 5 4 3 2 1 8 + + 4
5.2V 0.0V
C118 100u10 C117 100u10
+5V
L301
10uH
IC101 (2/2)
5.2V
13 GND 2
0V 7.7V
+7V
IC301
TX302
5.2V
14 1 VDD -7V +5V VDD 1
+5V
0V
7 +
R308 22
IC302
R312 82K R115 100 C116 47u10 8 9 10 11 12 13 14 C312 0.022
C115 47u10
DIGITAL REC IN
D IN
A
R313 47K
R415 8.2K R414 8.2K R416
2 R413 4.7K
8.2K
+5V
GND
AB
D OUT
R310 3.3K
C311 0.022
CNP301
3.0V
15 L3DATA 14 16 R402
+7V
DIGITAL OUT
1.5V 3.0V
R412 4.7K + +BV
( 15 )
+5V
24
23
22
21
18
15
14
13
12
11
+5V
AF
AG
AH
AI
AJ
AK
AL
AM
AN
R607 1K
3 C607 8
R617 330
R451 330
R455 100
J101 Lch
( ( ( ( ( ( ( ( ( ( (
R601 470
67
68
69
70
71
72
73
74
75
76
)
C453 470P
C459 470P
R605
22K
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73 P5 6G 22
( 50 ) (
C601 47u10
C615 100u10
F1
F1
F1
IC
P30
P29
P28
P27
P26
P1
P2
P3
P4
NP
NP
NX
NX
NX
NX
NX
Q451
C457 0.022 C456 820P R454 33K C454 470P C460 470P
2 VR901-2 VR901-1
REC LEVEL
1000P
C915
R609 1K
R613 100
AUX AMP R IN
12G
11G
10G
NX
9G
8G
7G
C603 220P
+7V
Q452
7.8V
R456 100
Rch
3 4 5 6 7
+7V
R608 1K
IC601 (2/2)
5 C608 + 6
R612 1.5K
C665 100u10
82 R618 330
GND OPEN
C614 47u10 R616 47K + C655 10u16 + R615 47K C651 150P R651 100K
R653 1K R681 1K
R602 470
5 C653 27P + 6 -
IC651 (1/2)
7
PHONES AMP
TOC
DISC
TRACK DATE
AUX VR R OUT
7.6V
8 9 VR981-2 1
HEADPHONE
CNW901
1
1a PHONES J981
2a
3a
5a
6a
C602 47u10
4b 4c
C652 150P
R652 100K
+7V
+ R614 100
C654
R682
C604 220P
-7V
-7V
C666 100u10
1 + 2 3
AUX AMP R IN AUX AMP I GND AUX AMP L IN AUX AMP R GND AUX VR L OUT GND AUX VR R OUT HP AMP GND HP AMP L OUT
MAIN SECTION IC101,651 IC201 IC301 IC302 IC501 IC601 : NJM45600 : uUDA1340 : 74HCU04 : 74HC10AP : ISB1233SOYX : NJM45800
3 C983 0.1 NP NP
1000P
C982
R668 82
1K
-8.0V
C981 1000P
IC651 (2/2)
10
27P
R659
C656 10u16
R654 1K
2 + 1
HP AMP R OUT
10
CNP473
PHONES LEVEL
RANDOM
TIMER REC
14G
15G
14G
13G
12G
11G
10G
P31
P32
P33
P34
P35
P36
9G
8G
7G
10
11
12
13
14
15
16
17
18
19
20
21
( 66 )
( 65 )
( 64 )
( 63 )
( 62 )
( 61 )
( 60 )
( 59 )
( 58 )
( 56 )
( 55 )
( 54 )
( 53 )
( 52 )
( 51 )
5 6
CNP902
FILMNT 2 FILMNT 1 AD5V BACK-UP5V 24 23 22 21 C908 1
R660 10
D651
-3.8V
C667 0.1
+7V
Q653
7 8
R670 330
R669
-6.5V
2.7K
L901 22uH +5V C909 1u50 C901 0.1 C910 0.1 + +5V +5V
+7V
10
HP AMP R OUT
-7V
C902 0.1
97
96
95
94
93
R945
C903 0.1
R944
R943
R942
R941
47K
: 2SC28788 : KTA1266GR : 2SB582-C : 2SD488-C : 2SD2012Y(FIN) : KRC1024M : KRC102M : MTZJ5R18 : MTZJ6R88 : MTZJ3308 : MTZ9R18 : MTZ9R19 : MTZ6R8A : MTZJ7R58 : MTZJ5R8C : MTZJ2700 : ISS133 : RL104A : SR19
-31.0V
D-1, 2 DAC CLK DAC MODE DAC DATA DFS MD DSCK MD K-DATA MD 7.5/5V MD DSTB P-IN MD P-OUT P-CNT P MUTE MD DATA MD RESET MD S-ID MD LOAD
18 17 16 15 14 13 12 11 10 9 8 7 6 5
10 15 14 16 18 20 21 23
+5V
C920 10u16
R901
+7V
10K
100
99
98
97
96
95
94
93
+ +BV 0.022
R968 10K
USEG23
USEG22
Q653
C223
1
RA902 1K
C530 0.022
+BV
C516 10u16
C515 10u16
C923 0.01
C501 100u25
1K
-BV
12K
R904
6.8K
R951
R955
+7V
30 33
C502 4700u25
C521 4700u25
8.1V
R508 100 8.8V R507 680 R509 820 R510 Q504 100 6.5V
+ -BV
Q503 7V AVR
R502 8.2 +BV C552 0.01
1.5K
R956
1.5K
D551
C551 0.01
D554
4 3 2 1
44 43 42 41
R952
R953
1.8K
(J)TYPE D553
F551 1A 125V HLD551 HLD552
MD SYN
10.7V
+BV
R957
D505
T551
+5V
1.8K
D552
5V AVR
C222 0.022 C514 10u16 +
6.0V
D502
C505 10u50
D513
C522 1000u6.3
D512
C518 100u10
NORMAL:0V LOADING:4.0V
R503 1.8K
NORMAL:4.7V LOADING:0V
+
HLD553
HLD554
C507 33u50
+ R504 33K
R959
Q505 D506
C517 100u10 +BV +5V
3.9K
D555
R517 220 R518 220
AC100V 50/60Hz
Q501
-36.5V
8.2
R960
5.6K
31.0V -31.6V
0.022
C519
D507
D501
R512 470
11.3V
Q506
+7.5V
R511 0.8
-31V
-31V AVR
0.3V
NORMAL:5.3V LOADING:6.7V
+5V
7.5V AVR
+5V
P MUTE
R920 470K
RX-IN
R516 220K
D508
R514 100K
32
33
34
35
36
C520 1000P
D510
+5V
RA928 1K
RA930 1K
HLD551
HLD552
RA931 1K
0.4V
R972 470K
R924 10K
Q902
31
2.0V
C525 100u10
( 31 )
R909
-31V
10
100
+5V
+ 4 RESET 3 LOAD SW 2 BUCK UP 1 PDOWN 1 MD SYN 2 MD LOAD 3 MD 5-10 4 MD RESTE 5 MD DATA 6 P MUTE 7 P-CNT 8 MD P-OUT 9 P-IN 10 MD DSTB 11 MD 7.5/5V 12 MD K-DATA 13 MD DSCK 14 DFS 15 DAC DATA 16 DAC MODE 17 DAC CLK 18 D-1.2 19 -31V FL VP 20 u-CON GND 21 BUCK UP 5V 22 AD5V 23 FIL1 24 FIL2
IC902
5.1V
2 OUT IN 1
CNP471
CNP472
4.2V
C971 10u16 + C970
4.2V
C907 1u50 +
5.1V.
C906 0.1 R926 1K
C905 12P
GND 3
UN970
100P
X902
REMOTE SENSOR
RESET IC
R910
C524 1000u6.3
+5V
C904
1.8K
15
14
13
HLD553
HLD554
( 33 )
RA933 1K
2.4V
37
T551
R922 10K
XCIN
3.0V
XCOUT
RESET
D509
P OUT
(E/T)TYPE
C511 47u25
10.7V
D504
C512 1u50
D508
5V AVR
D507
SW952
SW957
R905 12K
1.2K
1.2K
D506
31
IC501
D505
29
10uH
GND IN OUT
2 +7V
D503 D504
R903
L202
SW951
SW956
R954
C922 0.01
3.4V
8.1V
D502
1K
680
R950
-BV
-BV
D501
C509 47u25
R505
R501 8.2
D301
-8.9V
-13.0V
0.2V 5.1V
2 3 4
ENTER
RA903 1K
2.8V
RA904 1K
5 6 7 8
5.1V
NAME
RA908 1K
REC SW953
( 10 )
PLAY:0V REC:5.1V
RA912 1K
( 14 )
14 15 16 17
SW954
SW901
RA913 1K
( 15 )
RA914 1K
( 16 )
RA916 1K
0.8V 3.0V
18 19 20 21 22 23 24 25 26
DFS0/DFS1 (MD) DSTB (MD) DSCK (MD) K-DATA (MD)MD DATA (MD) LO/EJ
SW960
RA918 1K
( 20 )
RA927 1K
( 21 )
RA919 1K
( 23 )
5.1V
3.0V
R921 10K RA925 1K R923 10K
27 28
4.2V
P-IN P-CNT
Q901
( 29 )
1.8V 5.1V
29 30
5.1V
5.1V 5.1V
RA926 1K
( 30 )
USEG21
USEG19
VREF
AVSS
VEE
Q505
USEG24
D503
R969 10K
R506 100
Q502
Q504,506
R902
92
C221 0.022
C510 1u50
Q503
-7V AVR
-8.3V
-22.4V
-14.9V
-26.5V
-18.6V
-23.1V
-30.8V
5.1V
( )
-31V
12
NC
47K
47K
47K
47K
47K
+7V -7V
11
RESET SW
-31V
19
-31V
-31V
92
)
SW501
u-COM GND
20
( 49 ) (
MUTE DRIVE
C658 220u10
4 +
-6.4V
23
NC
12
IC
RESET SW
11
5G
F1
F1
F1
P6
47P
R619 10K
R457 10K
CNW903
72
C611
+7V
Q601
-6.4V
C914
-6.4V
DISPLAY SECTION
1000P
77
)
220P
7.6V
C613 47u10
) ( )
) ( )
) ( )
) ( )
) )
) )
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
a
94 95 96 78 79 80 81 82 83 84 85 86 87 88 89 90 92 93 97
( ( ) ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( ( (
f
1000P C916 52 51 50 49 48
b ANODE CONNECTION c
15G P1 P2 P3 P4 P5 5-1 14G 13G 12G 1-1 2-1 3-1 4-1 5-1 11G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 10G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 9G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 8G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 7G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 6G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 5G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 4G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 3G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 2G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 1G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7
71
70
69
68
67
66
65
64
63
62
61
60
59
58
56
55
54
53
FL901
e d (13G-15G)
6G
5G
4G
3G
2G
1G
1000P
C917
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
F2
F2
NP
NP
F2
RN1406 RN2404
57.
col
NC
NC
NC
NC
NC
NC
NC
NC
NC
NX
NP
NX
NX
NX
NX
NX
NP
4G
3G
2G
1G
F2
F2
F2
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
( 48 )
( 47 )
( 46 )
( 45 )
90
89
88
87
86
85
84
83
82
81
+5V R939
R938
R937
R936
R935
R934
R933
R932
R931
R930
47K
47K
47K
47K
47K
47K
47K
47K
47K
47K
-30.8V
-30.8V
-30.8V
-11.3V
-13.5V
-24.5V
-19.5V
-15.6V
-26.9V
5.1V
0V
91
90
89
88
87
86
85
84
83
82
USEG18
USEG17
USEG16
USEG15
USEG14
USEG13
USEG12
USEG10
USEG11
USEG09
VCC
81
USEG08 USEG07 USEG06 USEG05 USEG04 USEG03 USEG02 USEG01 USEG00 USEG25 USEG26 USEG27 USEG28
80 79 78 77 76 75 74 73 72 71 70 69 68 67
)
USEG29 USEG30 USEG31 USEG32 USEG33 USEG34 USEG35 UDIG15 UDIG14 UDIG13 UDIG12 UDIG11 UDIG10 UDIG09 UDIG08
66 65 64 63 62 61 60 59 58
57 56 55 54 53 52 51
( )
56 55 54 53 52 51
-28.6V
(MD) LOAD MD RESET (MD) SYN (MD) S-ID
UDIG07 UDIG06
UDIG00
UDIG01
UDIG02
UDIG03
UDIG04
38
39
40
42
43
44
45
46
47
48
49
41
2.1V
2.4V
0V
0V
0V
RA934 1K
RA935 1K
RA936 1K
X901
R911 1M
RA937 1K
0V
( 50 )
( 45 )
( 46 )
( 47 )
( 48 )
( 49 )
50
UDIG05
XOUT
VSS
XIN
( 41 )
( 42 )
( 43 )
( 44 )
58
-28.6V
59
-28.6V
60
-28.6V
61
-19.0V
62
-19.5V
63
-28.6V
64
-28.7V
65
-18.7V
u-COM
66
-18.3V
IC901
67
-24.6V
68
-26.7V
69
-24.3V
70
-19.0V
71
-19.0V
72
-26.5V
73
-23.6V
74
-26.5V
75
-28.7V
76
-19.5V
77
-19.0V
78
-26.5V
79
-24.3V
-12
-4
7a
8a
1 AM PM 8
CLOCK
15 16 17 18 19 20
15G
9 10 11 12 13 14
0dB
1-1
2-1
3-1
4-1
P6 P7 P8 P9
20 19 18 CLOCK
8d
1-2
P1
1-2
P2
2-2
P3
3-2
P4
4-2
P5
5-2
PRGM
OVER
P6
1-3
P7
2-3
P8
3-3
P9
4-3
P10
5-3
1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5
P11
P12
2-4
P13
3-4
P14
4-4
P15
5-4
17 16 15 14
8c 8e
1-4
NJM4580D
P16
1-5
P17
2-5
P18
3-5
P19
4-5
P20
5-5
NJM4560D NJM4565D
P21
1-6
P22
2-6
P23
3-6
P24
4-6
P25
5-6
13 12 11 10 9
8g
P26
1-7
P27
2-7
P28
3-7
P29
4-7
P30
5-7
MONO LP
REMAIN
7g 6g 5g 7b 7f col(up) 6b 6f 5b 5f 4b 2b 2f 1b 1f 3g 2g 1g 3b 3f
P31
P32
P33
P34
P35
P23 P24 P25 P26
2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7
(1G-12G)
8 7 PM AM
8b 8f
SWITCH P.C.B.
CNW902
3 2 1 3 2 1
TC9246F
2SD2012
6 5 4 3 2
8a
I/ ON/STANDBY SW950
TOTAL
7a 6a 5a 3a 2a 1a
( )
( )
( )
( )
( )
( )
( )
( )
( )
( )
4-7 5-7
-4
0dB OVER
SW955
PST9127NR
80
-16.2V
DISPLAY SECTION IC901 : IX0196AWZZ IC902 : PST9127 Q901,902 : 2SC2412KR UN970 : HL21043TH2 FL901 : 15-BT-37G
CAUTION: For continued safety, replace safety critical components only with manufacturer's recommended parts (refer to parts list). indicates safety critical components. For continued protection against risk of fire, replace only with same type and rating fuse(s). To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer. The DC voltage is an actual reading measured with a high impedance type voltmeter. The measurement value may vary depending on the measuring instruments used or on the product. Refer to the voltage during RECORDABLE MD PLAY unless otherwise specified; The value shown in ( ) is the voltage measured at the moment of STOP. The voltage followed by (REC) refers to the value during MD RECORDING.
DM-3090 (2/2)
DM-3090
Y22-7510-00
DM-3090
EXPLODED VIEW (MECHANISM)
A B
245
H
235
Kx2
210
CN1903 239
B1 B2
Kx2
RH
A1
i
237
225
209 222
PU
233
203
221
J D
A2
237 220
G G
231 SW1956
E
217
A
238
G
242
206
201 243
PWB-A
Cx2
207
Lx4
234
B
241
A1 B2 A2 B1
M
248
M
202
246 FM
249 247
LM DM
Fx3
A B C D E F G H i J K L M
M1.7x9.5 : N39-1795-45 M1.7x7.5 : N09-3426-08 M1.7x2 : N39-1720-45 M1.7x2.2 : N09-3115-08 M1.7x3 : N39-1730-45 M1.7x2.5 : N09-3347-08 M1.7x8.9 : N09-3352-08 M1.7x5 : N39-1750-45 1.5W3.2-.5C : N19-1179-04 1.2W3-0.25C : N19-2004-04 M2x4 : N09-3350-08 M1.7x3 : N09-3351-08 : N09-3428-08
DM-3090 MD MECHA
Parts with exploded view numbers larger than 700 are not supplied.
47
DM-3090
48
C D E
742
611
A Ax3 705
601
Ex2 720 E E E E
A B C D E F G H
3x8(BLK) : N89-2008-46 2.6x10 : N82-2610-46 3x6 : N82-3006-46 3x10(BLK) : N82-3010-46 3x6 : N82-3006-46 M 3x6 : N84-3006-45 M 4x8 : N82-4008-46 3x10 : N89-3010-45
713
Gx2
243 LT551
RESET LINE
SW951 SW954
SW953
REC LEVEL
SW501 J101
REC OUT PLAY IN REC IN
Parts with exploded numbers larger than 700 are not supplied.
SW955
A1
VR901
PHONES LEVEL
MULTI CONTROL
SW901
TIMER/DELETE ENTER
VR981 646
SW960
SW956
Bx2
SW958
Hx2
734 745
616
625
B C
635
746
634
726
603
Bx6
631
612
636
Bx2
645
707
PHONES
630x2 630x2
Ex2 Cx3 Ex2
610 637
C
DM-3090
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Add- New Parts No. Ref. No Description ress Parts
1
Destination Remarks
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Ref. No C315 C451,452 C453,454 C455,456 C457 C459,460 C461 C470 C501 C502 C504 C505 C507 C509 C510 C511 C512 C513 C514-516 C517,518 C519 C520 C521 C522 C524 C525 C530 C531 C551,552 C561 C601,602 C603,604 C607,608 C611,612 C613,614 C615,616 C651,652 C653,654 C655,656 C657,658 C665,666 C667 C901-903 C904 C905 C906 C907 C908 C909 C910 C914-917 C920 C922,923 C970 C971 Address New Parts Parts No. CK45FB1H103K CE04KW1A470M CK45FB1H471K CK45FB1H821K CK45FF1H223Z CK45FB1H471K CK45FB1H103K CK45FB1H101K CE04KW1E102M CE04KW1E472M CE04KW1H221M CE04KW1H100M CE04KW1H330M CE04KW1E470M CE04KW1H010M CE04KW1E470M CE04KW1H010M CE04KW1E470M CE04KW1C100M CE04KW1A101M CK45FF1H223Z CK45FB1H102K CE04KW1E472M CE04KW0J102M CE04KW0J102M CE04KW1A101M CK45FF1H223Z CF92FV1H104J CK45FF1H103Z CK45FF1H103Z CE04KW1A470M CK45FB1H221K CK45FB1H221K C91-0737-05 CE04KW1A470M CE04KW1A101M CK45FB1H151K C91-0731-05 CE04KW1C100M CE04KW1A221M CE04KW1A101M CF92FV1H104J CK73FB1H104Z CC73FCH1H680J CC73FCH1H120J CK73FB1H104Z CE04KW1H1R0M CK73EF1E105Z CE04KW1H1R0M CK73FB1H104Z CK73FB1H102K CE04KW1C100M CK73FB1H103Z CK73FB1H101K CE04KW1C100M CERAMIC ELECTRO CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO CERAMIC CERAMIC ELECTRO ELECTRO ELECTRO ELECTRO CERAMIC MF-C CERAMIC CERAMIC ELECTRO CERAMIC CERAMIC CERAMIC ELECTRO ELECTRO CERAMIC CERAMIC ELECTRO ELECTRO ELECTRO MF-C CHIP C CHIP C CHIP C CHIP C ELECTRO CHIP C ELECTRO CHIP C CHIP C ELECTRO CHIP C CHIP C ELECTRO Description 0.010UF 47UF 470PF 820PF 0.022UF 470PF 0.010UF 100PF 1000UF 4700UF 220UF 10UF 33UF 47UF 1.0UF 47UF 1.0UF 47UF 10UF 100UF 0.022UF 1000PF 4700UF 1000UF 1000UF 100UF 0.022UF 0.10UF 0.010UF 0.010UF 47UF 220PF 220PF 47PF 47UF 100UF 150PF 27PF 10UF 220UF 100UF 0.10UF 0.10UF 68PF 12PF 0.10UF 1.0UF 1.0UF 1.0UF 0.10UF 1000PF 10UF 0.010UF 100PF 10UF K 10WV K K Z K K K 25WV 25WV 50WV 50WV 50WV 25WV 50WV 25WV 50WV 25WV 16WV 10WV Destination
2
Remarks
DM-3090
601 602 603 604 606 610 611 612 615 616 616 625 630 631 634 635 636 637 638 2D,2E 2E 2E 2C 2D 1C 1C 1D 1C 2C 2C 1C 2C 1C 2C 8 8 8 8 8 8 8 A01-3562-08 A09-0337-08 A29-0898-08 A60-1370-08 A70-1208-08 B10-2457-08 B19-1529-05 B43-0302-04 B60-3574-08 B60-3575-08 E30-0505-05 E30-2579-05 E30-2718-05 8 8 8 8 8 8 8 8 8 8 8 8 8 8 G01-4048-08 H10-7415-08 H13-0291-08 H13-0292-08 H13-0293-08 H20-0601-08 H50-2695-08 H50-2697-08 J02-1410-08 J42-0338-08 J13-0075-05 K27-2261-08 K27-2262-08 K29-6946-08 K29-6947-08 METALLIC CABINET BATTERY COVER PANEL FRONT PANEL REMOTE CONTROL ASSY FRONT GLASS OPTICAL FIBER KENWOOD BADGE INSTRUCTION MANUAL INSTRUCTION MANUAL AUDIO CORD AC POWER CORD AC POWER CORD SPRING POLYSTYRENE FORMED FIXTURE PACKING FIXTURE CARTON BOARD CARTON BOARD PROTECTION BAG ITEM CARTON CASE ITEM CARTON CASE INSULATOR POWER CORD BUSHING FUSE HOLDER KNOB KNOB KNOB KNOB (POWER) (JOG) (REC/HP) T
T E E T
1C 2E 2E 2C
PARTS LIST
E T
Z K 25WV 6.3WV 6.3WV 10WV Z J Z Z 10WV K K J 10WV 10WV K J 16WV 10WV 10WV J Z J J
ELECTRIC UNIT
C102 C105,106 C107,108 C109,110 C113,114 C115,116 C117,118 C119 C201 C202,203 C205 C206 C207 C208 C209 C212 C220 C221 C222,223 C301 C302-305 C310-314 L : Scandinavia Y : PX(Far East, Hawaii) Y : AAFES(Europe) CK45FF1H223Z CK45FB1H221K CE04KW1H010M CK45FB1H221K CC45FSL1H470J CE04KW1A470M CE04KW1A101M CK45FF1H223Z CE04KW1A101M CE04KW1A470M CE04KW1E4R7M CE04KW1H010M CE04KW1A101M C90-3231-05 CE04KW1E4R7M C90-3231-05 CK45FB1H102K CK45FF1H223Z CK45FF1H223Z CK45FF1H103Z CK45FF1H223Z CK45FF1H223Z CERAMIC CERAMIC ELECTRO CERAMIC CERAMIC ELECTRO ELECTRO CERAMIC ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO ELECTRO CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC 0.022UF 220PF 1.0UF 220PF 47PF 47UF 100UF 0.022UF 100UF 47UF 4.7UF 1.0UF 100UF 3.3UF 4.7UF 3.3UF 1000PF 0.022UF 0.022UF 0.010UF 0.022UF 0.022UF Z K 50WV K J 10WV 10WV Z 10WV 10WV 25WV 50WV 10WV 25WV 25WV 25WV K Z Z Z Z Z
DM-3090
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
49
DM-3090
50
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Add- New Parts No. Ref. No Description ress Parts C981,982 C983 CNW301 CNP471 CNP472 CNP473 CNP902 CNW901 CNW902 CNW903 J101 J301 J981 F551,552 L101 L201,202 L301,302 L901 T551 X901 X902 R501,502 R511 R551 R901 R902 R903 R904 R905 R906 R909 R910 R911 R920 R922-924 R926 R930-645 R950 R951 R952 R953 R954 R955 R956 R957 R958 R959 R960 R968,969 R970 R971 R972 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 CK73FB1H102K CK73FB1E104Z E35-2102-08 E40-8226-08 E40-8227-08 E40-8262-08 E40-8263-08 E35-2143-08 E35-2144-08 E40-8231-08 E63-1031-08 E63-1032-08 E11-0345-08 F53-0162-08 L90-0304-08 L90-0305-08 L90-0305-08 L90-0306-08 L07-2543-08 L77-2227-08 L77-2168-08 X1067 X1066 X1067 RK73FB2A103J RK73FB2A392J RK73FB2A123J RK73FB2A682J RK73FB2A123J RK73FB2A224J RK73FB2A182J RK73FB2A475J RK73FB2A105J RK73FB2A474J RK73FB2A103J RK73FB2A102J RK73FB2A473J RK73FB2A102J RK73FB2A122J RK73FB2A152J RK73FB2A182J RK73FB2A102J RK73FB2A122J RK73FB2A152J RK73FB2A182J RK73FB2A272J RK73FB2A392J RK73FB2A562J RK73FB2A103J RK73FB2A102J RK73FB2A101J RK73FB2A474J CHIP C CHIP C 1000PF 0.10UF K Z 4PIN
3
Destination Remarks
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Ref. No RA903 RA908 RA912 RA913 RA914 RA916 RA918 RA919 RA925 RA926 RA927 RA928 RA930 RA931 RA933 RA934 RA935 RA937 VR901 VR981 SW501 SW901 SW950 SW951 SW952 Address New Parts Parts No. RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J RK73FB2A102J R39-0016-08 R39-0017-08 S68-0091-08 T99-0607-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 S70-0057-08 MTZJ5.1(B) MTZJ6.8(B) MTZJ330A MTZJ9R1B MTZJ6.8 MTZJ7.5(B) MTZJ5.6 MTZJ270D 1SS133 1SS133 RL104A MTZJ9R1B B30-2527-08 NJM4565D UDA1340 74HCU04 74HC10AP S81233YX NJM4580D NJM4560D CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R Description 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K 1.0K J J J J J J J J J J J J J J J 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W Destination
4
Remarks
CONNECTOR ASSY PLUG 24PIN PLUG 24PIN CONNECTOR 12PIN PLUG 24PIN
FLAT CABLE 3PIN FLAT CABLE 4PIN CONNECTOR ASSY 12PIN ANALOGUE OUTPUT TERMINAL DIGITAL INPUT TERMINAL HEAD PHONE JACK FUSE T1A250V
COIL 0.22UH COIL 10UH COIL 10UH COIL 22UH POWER TRANSFORMER FILTER CRYSTAL POSISTOR POSISTOR POSISTOR CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R 4.19MHz 32.768kHz 8.2 8.2 8.2 10K 3.9K 12K 6.8K 12K 220K 1.8K 4.7M 1.0M 470K 10K 1.0K 47K 1.0K 1.2K 1.5K 1.8K 1.0K 1.2K 1.5K 1.8K 2.7K 3.9K 5.6K 10K 1.0K 100 470K
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
CHIP R 1.0K J CHIP R 1.0K J CHIP R 1.0K J VIRIABLE RESIST 5k (AUX VOL.) VARIABLE RESIST 1k (HP VOL.) SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE INDICATOR TUBE IC(OP AMP X2)) IC IC IC IC IC(OP AMP X2)) IC(OP AMP X2)) RESET JOG POWER PLAY STOP REC CUE EJECT ENTER NAME TIMER DISP REVIEW TIME
PARTS LIST
J J J J J J J J J J J J J J J J J J J J J J J J J J J J
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
SW953 SW954 SW955 SW956 SW957 SW958 SW959 SW960 SW961 D301 D501 D502 D503,504 D505 D506 D507 D508 D509,510 D512,513 D551-555 D651 FL901 IC101 IC201 IC301 IC302 IC501 IC601 IC651
8 8 8 8 8
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Add- New Parts No. Ref. No Description ress Parts IC901 IC902 Q451,452 Q501 Q502 Q503 Q504 Q505 Q506 Q601,602 Q653 Q901,902 RX302 TX302 UN970 IX0196AWZZ PST9127NR 2SC2878 KTA1266(Y) 2SB562 2SD468 2SD2012 KRC102M 2SD2012 2SC2878 KRC102M 2SC2412 W02-2643-08 W02-2643-08 W02-2642-08 IC IC(SYSTEM RESET) TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR OPTICAL DIGITAL OUTPUT OPTICAL DIGITAL INPUT REMOCON SENSOR 21043TH2
5
Destination Remarks
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Ref. No C1656,57 C1661 C1724 C1801 C1802 C1803 C1805 C1806 C1807 C1913 C1917 C1927 C1951 C1952 C1953 C1954 C1955 C1956 C1957 C1958 C1964 C1990 C1991 JC121 JC170,71 JC196 CN1101 CN1252 CN1601 CN1602 CN1603 CN1604 CN1901 CN1902 CN1904 CW1901 CW1903 L1101 L1102 L1201 L1203 L1251 L1601 L1950 XL1201 C1111 J1405 LR190 R1100 R1102 R1105 R1106 R1107 2D 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 Address New Parts Parts No. CK73GB1H562K C92-0151-08 CC73GCH1H220J CK73EF1C225Z C92-0151-08 CK73EF1C225Z CK73FF1C105Z C92-0172-08 C92-0174-08 CC73GCH1H220J CC73GCH1H680J CK73GB1C473K CK73GB1C473K C93-0035-08 CK73FB1C474K CC73GCH1H150J CK73GB1C473K C92-0175-08 C92-0176-08 CK73GB1C473K CK73GB1H102K C93-0033-08 C92-0172-08 CK73GB1C473K CC73FCH1H220J CC73FCH1H220J E40-8210-08 E40-8080-08 E40-8211-08 E40-8212-08 E40-8078-08 E40-8213-08 E40-8209-08 E40-8214-08 E40-8084-08 E35-2070-08 E35-2069-08 L90-0099-08 L90-0100-08 L90-0100-08 L90-0301-08 L90-0302-08 L90-0303-08 L90-0303-08 L77-2224-08 R92-1824-08 RK73GB1J103J RK73FB2A220J RK73EB2B270J RK73GB1J561J RK73GB1J394J RK73GB1J103J RK73GB1J1R0J CHIP C ELECTRO CHIP C CHIP C ELECTRO CHIP C CHIP C CHIP-C ELECTRO CHIP C CHIP C CHIP C CHIP C CERAMIC CHIP C CHIP C CHIP C ELECTRO ELECTRO CHIP C CHIP C CERAMIC CHIP-C CHIP C CHIP C CHIP C Description 5600PF 100UF 22PF 2.2UF 100UF 2.2UF 1.0UF 10UF 220UF 22PF 68PF 0.047UF 0.047UF 0.01UF 0.47UF 15PF 0.047UF 47UF 100UF 0.047UF 1000PF 1UF 10UF 0.047UF 22PF 22PF K 10WV J Z 10WV Z Z K 4WV J J K K K K J K 6.3WV 6.3WV K K K K K J J 28P 5P Destination
6
Remarks
8 8 8
MD MECHANISM UNIT
C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1109 C1110 C1112-16 C1117 C1118 C1121 C1145 C1202,03 C1204,05 C1206,07 C1208 C1209-11 C1251 C1252 C1254 C1255 C1401,02 C1403 C1405 C1406 C1407 C1412 C1421-24 C1425 C1601,02 C1604 C1605 C1609 C1610 C1631 C1650-53 C1654,55 8 8 8 8 8 8 8 8 C93-0033-08 C93-0033-08 CK73FF1C105Z CK73FB1H273K C93-0033-08 CK73FB1C474K CK73FB1H472K C93-0033-08 CK73FB1C474K C93-0034-08 CK73GB1H332K CK73FB1H333K CK73FF1C105Z CK73GB1C333K CK73FF1C105Z CC73GCH1H120J CK73FF1C105Z CK73GB1C473K CK73FF1C105Z CK73GB1C273K CC73FCH1H121J C92-0172-08 C92-0171-08 CK73GB1C473K CK73GB1H681K CK73GF1E104Z CK73FF1C105Z CK73GB1C223K CK73GB1H681K CK73GB1C223K CK73GB1C473K CK73FF1C105Z CC73GCH1H560J C92-0151-08 CK73EF1C105Z C92-0172-08 CK73FF1C105Z CC73GSL1H821J CK73GB1E153K CERAMIC CERAMIC CHIP C CHIP C CERAMIC CHIP C CHIP C CERAMIC CHIP C CERAMIC CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-C CHIP-C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C ELECTRO CHIP C CHIP-C CHIP C CHIP C CHIP C 1UF 1UF 1.0UF 0.027UF 1UF 0.47UF 4700PF 1UF 0.47UF 270PF 3300PF 0.033UF 1.0UF 0.033UF 1.0UF 12PF 1.0UF 0.047UF 1.0UF 0.027UF 120PF 10UF 4.7UF 0.047UF 680PF 0.10UF 1.0UF 0.022UF 680PF 0.022UF 0.047UF 1.0UF 56PF 100UF 1.0UF 10UF 1.0UF 820PF 0.015UF K K Z K K K K K K J K K Z K Z J Z K Z K J K K K K Z Z K K K K Z J 10WV Z K Z J K
8 8
PARTS LIST
8 8
8 8
FLAT CABLE CONNECTOR PIN ASSY 2P FLAT CABLE CONNECTOR PIN ASSY 2P PIN ASSY 2P PIN ASSY 2P FLAT CABLE CONNECTOR FLAT CABLE CONNECTOR PIN ASSY 4P FLAT CABLE WIRING HARNESS COIL COIL COIL COIL COIL COIL COIL CRYSTAL JUMPER R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R 10UH 0.47UH 0.47UH 4.7UH 470UH
24P
1UH 1UH 33.8688MHZ 0 10K 22 27 560 390K 10K 1 J J J J J J J J 1/10W 1/16W 1/10W 1/8W 1/16W 1/16W 1/16W 1/16W
DM-3090
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
51
DM-3090
52
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Add- New Parts No. Ref. No Description ress Parts R1150-54 R1155 R1166 R1201 R1202 R1210 R1211 R1221 R1223 R1251 R1252,53 R1254 R1255 R1261-63 R1266 R1269 R1281 R1401 R1404 R1406,07 R1408 R1409 R1412 R1413 R1414 R1415 R1416 R1418 R1420 R1422-24 R1425 R1426 R1427 R1428 R1429,30 R1452 R1454 R1456 R1458 R1459 R1460 R1462 R1463 R1464 R1466 R1471 R1472 R1473 R1474-76 R1477 R1609 R1610 R1611 R1612 R1613 8 8 8 RK73GB1J223J RK73GB1J563J RK73GB1J122J RK73GB1J151J RK73GB1J105J RK73GB1J101J RK73GB1J221J RK73GB1J221J RK73FB2A681J RK73GB1J100J R92-1824-08 RK73FB2A221J R92-1823-08 RK73GB1J103J RK73GB1J103J R92-1823-08 RK73GB1J470J RK73GB1J102J RK73GB1J102J RK73GB1J332J RK73GB1J104J RK73GB1J102J RK73GB1J104J RK73GB1J332J RK73GB1J103J RK73GB1J102J RK73GB1J103J RK73GB1J473J RK73GB1J102J RK73GB1J103J RK73GB1J272J RK73GB1J102J RK73GB1J472J RK73GB1J102J RK73GB1J103J RK73GB1J332J RK73GB1J102J RK73GB1J102J RK73GB1J682J RK73GB1J103J RK73GB1J682J RK73GB1J682J RK73GB1J103J RK73GB1J221J RK73GB1J221J RK73GB1J103J RK73GB1J473J RK73GB1J104J RK73GB1J102J RK73GB1J103J RK73GB1J152J R92-1869-08 R92-1870-08 RK73GB1J563J RK73GB1J273J CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R JUMPER R CHIP R JUMPER R CHIP R CHIP R JUMPER R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R METAL METAL CHIP R CHIP R 22K 56K 1.2K 150 1.0M 100 220 220 680 10 0 220 0 10K 10K 0 47 1.0K 1.0K 3.3K 100K 1.0K 100K 3.3K 10K 1.0K 10K 47K 1.0K 10K 2.7K 1.0K 4.7K 1.0K 10K 3.3K 1.0K 1.0K 6.8K 10K 6.8K 6.8K 10K 220 220 10K 47K 100K 1.0K 10K 1.5K 30K 12K 56K 27K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J D D J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
7
Destination Remarks
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Ref. No R1614 R1617 R1620 R1650 R1651 R1652 R1653 R1654 R1655 R1656 R1657 R1658 R1659 R1660 R1661 R1662 R1663 R1664 R1665 R1666,67 R1668,69 R1708 R1733 R1758,59 R1801 R1802 R1804 R1805 R1808 R1809 R1820,21 R1827 R1901 R1902 R1903,04 R1927 R1939 R1940 R1947 R1952,53 R1961 R1962 R1963 R1964 R1965 R1967 R1968 R1969 R1973 R1974 R1994 SW1952 2D SW1953 2D SW1954,55 2D 8 8 8 8 Address New Parts Parts No. R92-1871-08 RK73GB1J473J R92-1823-08 RK73GB1J103J RK73GB1J104J RK73GB1J103J RK73GB1J104J RK73GB1J682J RK73GB1J124J RK73GB1J682J RK73GB1J124J RK73GB1J153J RK73GB1J823J RK73GB1J153J RK73GB1J823J RK73GB1J103J RK73GB1J623J RK73GB1J103J RK73GB1J623J RK73GB1J223J RK73GB1J682J RK73GB1J682J RK73GB1J102J RK73GB1J102J RK73GB1J182J RK73GB1J271J R92-1873-08 R92-1874-08 RK73GB1J273J RK73GB1J391J RK73FB2A1R0J RK73GB1J271J RK73FB2A471J RK73FB2A182J RK73FB2A821J RK73FB2A220J RK73GB1J102J RK73FB1J221J RK73FB2A470J RK73GB1J470J RK73GB1J101J RK73GB1J224J RK73GB1J152J RK73GB1J682J RK73GB1J103J RK73GB1J470J RK73GB1J221J RK73EB2B560J RK73GB1J682J RK73GB1J221J RK73GB1J470J S68-0090-08 S64-0023-05 S64-0035-08 METAL CHIP R JUMPER R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R METAL METAL CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R PUSH SWITCH LEVER SWITCH LEVER SWITCH Description 18K 47K 0 10K 100K 10K 100K 6.8K 120K 6.8K 120K 15K 82K 15K 82K 10K 62K 10K 62K 22K 6.8K 6.8K 1.0K 1.0K 1.8K 270 220K 100K 27K 390 1 270 470 1.8K 820 22 1.0K 220 47 47 100 220K 1.5K 6.8K 10K 47 220 56 6.8K 220 47 D J J J J J J J J J J J J J J J J J J J J J J J J J D D J J J J J J J J J J J J J J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/10W 1/10W 1/10W 1/10W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W Destination
8
Remarks
PARTS LIST
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Add- New Parts No. Ref. No Description ress Parts SW1956 D1251,52 D1990 IC1101 IC1201 IC1202 IC1251 IC1401 IC1402 IC1601 IC1801 IC1906 IC1907 IC1916 IC1990 Q1251,52 Q1253,54 Q1401 Q1402 Q1403 Q1404 Q1451 Q1601 Q1801 Q1802,03 Q1807 Q1820 Q1821,22 2D 8 S64-0036-08 SB0209CP 1SS372 IR3R55 LR37648 IX2474AF 74ACT02F IX0227AW S29294A M56578FP XC62EP32 TC7ST08F TC9246F 74VHC08FT 74AC04FS 2SK2909 2SK1473 RN2404 RNC1404 RN2404 RNC1404 RNC1407 2SA1314C 2SA1314C RN1406 2SA1314C 2SA1162G RNC1407 LEVER SWITCH DIODE DIODE IC IC IC IC IC IC IC IC IC IC(CLOCK GENERATION) IC IC FET FET TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
9
Destination Remarks
8 New Parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Ref. No 226 229 230 231 232 233 234 235 237 238 239 242 243 245 246 247 250 249 248 B D F G K L M DM FM LM PU RH 3A 3A 3A 2A 1A 8 8 8 8 8 3B Address 2A 1A 1A 2A 2A 2A 3A 1B 2B 2B 1B 2B 2B 1A 3B 3B New Parts 8 8 8 8 8 Parts No. D13-1863-08 D13-1864-08 D14-0394-08 D19-0312-08 D21-1895-08 D10-3699-08 D10-3702-08 A01-3562-08 J02-1183-08 J02-1184-08 G11-2380-08 E35-2067-08 E35-2068-08 F19-1083-08 D10-3796-08 D10-3797-08 F19-1084-08 G09-0666-08 J90-0859-08 N09-3426-08 N09-3115-08 N09-3347-08 N09-3352-08 N09-3350-08 N09-3351-08 N09-3428-08 T42-0904-08 T42-0905-08 T42-0906-08 T25-0073-08 T30-0017-08 LACK GEAR GEAR ROLLER LEAD SCREW SHAFT ROD ROD CASE INSULATOR INSULATOR CUSHION FLAT CABLE WIRING HARNESS SHEET ARM(A) ARM(B) SHEET SPRING (ARM) Description Destination
0
Remarks
8 8
8 8 8 8 8
8 8 8 8 8 8 8 8 8 8
8 8 8 8 8 8 8 8 8
PARTS LIST
MOUNTING HARDWARE SCREW SCREW SCREW SCREW SCREW SCREW SCREW M1.7X7.5 M1.4X2.2 M1.7X2.5 M1.7X8.9 M2.0X4.0 M1.7X3.0
MD MECHANISM ASSY
201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 2B 3A 2B 1A 2A 3B 1A 2A 1A 1A 1A 1A 3A 2A 1A 2A 1A 2A 2B 2A 2A 2A 3A 2A 8 8 8 8 8 8 8 8 8 8 8 8 8 8 J90-0857-08 J90-0858-08 A13-3122-08 A10-3416-08 J19-5899-08 D10-3789-08 D10-3790-08 D10-3791-08 D10-3792-08 D10-3793-08 D10-3794-08 D10-3795-08 G01-4046-08 G01-4047-08 G01-3972-08 G01-3974-08 G01-3971-08 G01-3976-08 G02-1651-08 G02-1652-08 G01-3973-08 D13-1859-08 D13-1860-08 D13-1861-08 D13-1862-08 GUIDE GUIDE FRAME CHASSIS ASSY HOLDER SLIDER ASSY ARM ARM ARM ASSY SLIDER ARM SLIDER TORSION COIL SPRING TORSION COIL SPRING EXTENSION SPRING EXTENSION SPRING EXTENSION SPRING TORSION COIL SPRING FLAT SPRING FLAT SPRING EXTENSION SPRING GEAR GEAR GEAR GEAR
MOTOR ASSY M901 MOTOR ASSY M902 MOTOR ASSY M903 OPTICA PICKUP RECORDING HEAD
DM-3090
8 8 8 8 8 8
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
K : USA P : Canada R : Mexico T : Europe E : Europe G : Germany X : Australia M : Other Areas indicates safety critical components.
53
DM-3090
SPECIFICATIONS
[Format]
System ................................................................................................................ Minidisc digital audio system Laser ................................................................................................................... Semiconductor laser Recording method ............................................................................................. Field modulation overwrite method Audio compression ............................................................................................ ATRAC (Adaptive TRansform Acoustic Coding) Playing rotation .................................................................................................. Approx. 400 rpm ~ 900 rpm (CLV)
[General]
Power consumption ........................................................................................... 17 W Dimensions ......................................................................................................... W : 440 mm (17 - 5 / 16) ........................................................................................................................ H : 94 mm ( 3 - 11 / 16) ........................................................................................................................ D : 300 mm (11 - 13 / 16) Weight (Net) ........................................................................................................ 3.55 kg (7.9 lb)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Note: Component and circuit are subject to modification to insure best operation under differing local conditions. This manual is based on Europe (E) standard, and provides information on regional circuit modification through use of alternate schematic diagrams, and information on regional component variations through use of parts list.