Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Introduction
When working with plastics there is often a need to identify which particular plastic material has been used for a given product. This is essential to get an idea of the cost and likely properties of the product. The identification of plastics is generally very difficult due to: The wide range of basic polymers that are available for use. The wide range of additives that can be used to modify the properties of the basic polymer. The wide range of mixtures or compounds of polymers that can be manufactured to get the required properties.
Despite this there are some simple tests that can be carried out to get a basic idea of the possible base polymer used for the manufacture of any given product. These tests are simple to carry out for most people and require no special equipment. These tests are a first guess only at the material type and should always be confirmed if definite answers are needed. Note: The tests given here can be dangerous if performed improperly. Carry all testing out with care, particularly when burning or smelling plastics fume, some fumes are dangerous! e careful when using burning tests and carry out the tests under supervision only. There are also some more complicated tests that can be carried out but these require some standard laboratory equipment, details of these are given in !imple "ethods for #dentification of $lastics by Dietrich %raun &'anser (erlag #!%) *+*,+-.-,/*+, for 0nglish text1 but there is no substitute for a full analysis of the plastic. Details of the these methods can be obtained direct form Tangram Technology 2td.
The basic tests to apply are: 2ook at the sample. 4eel the sample. 5ut the sample. !ee if it floats in water. %urn some of the sample.
These tests will give you a fair idea of what the basic polymer is. Note: The tests given here are not necessarily definitive and the presence of certain additives !for instance flame retardants" can significantly change the behaviour of a product.
Testing
#tage $: %oo& at the sample This will give you a lot of information. The colour of the plastic will give you some information. !ome polymers have restricted colour ranges, particularly the thermosetting types. 6thers tend to be more glossy in colour &polypropylene1, whereas some are both glossy and glassy &the acrylics1. #tage ': (eel the sample 3fter you have carried out the tests in the is series a few times you will start to get the feel for various plastics. The polyolefins have a very distinctive feel and you can generally tell if it is one of them. The presence of glass fibre or other reinforcement materials can alter the feel and stiffness of the sample but you can sometimes tell by the feel if there is a reinforcement present. #tage ): Cut a thin sliver from the edge of the sample. (ollow the lin&s to the appropriate page. The first test is to cut a small sliver off the sample. This tells you a lot about the type of plastic you are trying to identify $owdery chips formed + 7enerally thermosetting material. !mooth sliver of plastic formed + 7enerally thermoplastic material. The links will take you to the appropriate page and possibly identify the plastic you have.
Thermosetting materials
(lame testing
'old the sample in a lighted match and smell. Note: Ta&e care when smelling any plastic material. *a&e sure the flame is totally out. +o not directly inhale the fumes from the burning sample. ,old the sample away from your nose !about '- . )- cm" and sniff /ust enough to get the
smell. +o not inhale deeply. Ta&e care of any dripping polymer . it will be very hot and can burn.
0esults
%urns but is self+extinguishing. 5arbolic smell present. The sample is usually black or brown + Phenol formaldehyde resin. %urns but is self+extinguishing. !harp acrid odour. The sample is light in colour +
#cuff testing
!cuff the sample with your fingernail.
0esults
!cuffs with fingernail + 2rea
Thermoplastic materials
5onfirm that the plastic is a thermoplastic by heating a wire in a match and touching plastic with hot wire. "elting confirms that it is thermoplastic otherwise it is a thermoset.
+rop testing
Drop the sample onto a hard surface.
0esults
"etallic ringing noise generally indicates the presence of styrene based polymer. !tyrene based polymers. 3bsence of metallic ringing noise means it is not generally a styrene based polymer &unless it is a foamed plastic, in which case the foam will be evident or it may be 'igh #mpact $olystyrene, $!+'# in which case it will have the $! type of feel to it1. )on+ styrene based polymers.
'old the sample in a lighted match and smell. Note: Ta&e care when smelling any plastic material. *a&e sure the flame is totally out. +o not directly inhale the fumes from the burning sample. ,old the sample away from your nose !about '- . )- cm" and sniff /ust enough to get the smell. +o not inhale deeply. Ta&e care of any dripping polymer . it will be very hot and can burn.
0esults
5haracteristic smell of polystyrene + Polystyrene 5haracteristic smell of polystyrene 9 a bitter smell +
#tyrene.acrylonitrile 3crylonitrile.butadiene.
styrene copolymer.
0esults
!ample floats + generally a polyolefin. !ample sinks + not generally a polyolefin.
#cratch testing
!cratch the sample with your fingernail.
(lame testing
'old the sample in a lighted match and smell. Note: Ta&e care when smelling any plastic material. *a&e sure the flame is totally out. +o not directly inhale the fumes from the burning sample. ,old the
sample away from your nose !about '- . )- cm" and sniff /ust enough to get the smell. +o not inhale deeply. Ta&e care of any dripping polymer . it will be very hot and can burn.
0esults
7lossy surface, does not scratch, burns with the smell of paraffin wax +
Polypropylene
7lossy surface, slight scratching, burns and drips like wax +
Polyethylene !,igh .
+ensity"
)ot very glossy surface, scratches easily, burns with the smell of paraffin wax
0esults
#gnites, continues to burn after match removed and burns with a clear flame. Difficult to ignite and self+extinguishing ¬e the colour of the flame and how easily it starts to burn1.
0esults
4ruity odour + 3crylic
!probably P**3".
acetate or Cellulose propionate !but no test available to differentiate between the two".
%urns with smell of bad butter + Cellulose
acetate butyrate.
0esults
!ample burns with a green flame: 3crid smell, material is soft and flexible + Plasticised
Poly!vinyl Poly!vinyl
chloride".
3crid smell, material is stiff and glossy + 2nplastised
chloride".
!ample burns with a yellow flame: !mell of formaldehyde + Polyacetal. )o real smell, sample has slippery feel. $ush cold metal point onto hot surface and withdraw, if threads of material are formed +
Polyamide !Nylon".
)o real flame formed, material forms a cellular structure and then decomposes + Polycarbonate.