Sei sulla pagina 1di 7

Professional Power Amplifier

- A 2U rack, 2 channel amplifier capable of 1150W/1850W into 4 load (bridged mono) - 2 load stable per channel, 4 load stable in bridged mono - Switch Mode Power Supply available for high efficiency and low weight - Forced air cooled(front panel intake, rear panel exhaust) - Front panel indicators for clip, protect and power - Rack ears for permanent installation in a standard 19" (rack mount width) enclosure - Detachable AC power cord - Power Source : 120VAC, 230VAC ; 50/60Hz (supplied AC mains depends on country requirements) - Power Consumption(1/8 power) V-1000 : 120VAC(3A), 230VAC(4A) V-2000 : 120VAC(6A), 230VAC(8.5A) - Weight : V-1000 : 10.3kg / 22.7lb, V-2000 : 10.5kg / 23lb - Dimension(W H D) : 482 88 407mm / 19 3.5 16in

Spec Rated Power RL=8 @ 0.1% THD (Stereo) RL=4 @ 0.1% THD (Stereo) RL=2 @ 0.5% THD (Stereo) RL=8 1kHz @ 0.1% THD (Bridged) RL=4 1kHz @ 0.5% THD (Bridged) Input Sensitivity (4) Input Impedance Slew Rate (8, Full Swing) Frequency Response (1W@8) Total Harmonic Distortion f=20Hz ~ 20kHz, 1/10 Power Signal to Noise Ratio Damping Factor (8, 1kHz) Residual Noise

Model 120VAC 190W 340W 580W 720W 1200W

V-1000
230VAC 180W 320W 580W 700W 1150W 1V 12 k (Balanced, Unbalanced) 120VAC 320W 550W 900W 1150W 1900W

V-2000
230VAC 300W 530W 900W 1100W 1850W 1.3V

20V/sec
20Hz~20kHz : -0.3dB, 10Hz~83kHz : -3dB <0.05% 107dB >400 75dBu >70dB 31dB 109dB

Channel Separation (1kHz, Half Power @8) Voltage Gain @4 (Gain SW 1V)

Professional & Commercial Audio Products

Professional Power Amplifier

- A 2U rack, 2 channel amplifier capable of 3200W/4000W into 4 load (bridged mono) - 2 load stable per channel, 4 load stable in bridged mono - Switch Mode Power Supply available for high efficiency and low weight - Selectable High Pass Filter on each channel - Clip limiter circuitry - Forced air cooled(front panel intake, rear panel exhaust) - Front panel indicators for output signal, clip, protect and power - Rack Ears for permanent installation in a standard 19" (rack mount width) enclosure - Detachable AC power cord - Power Source : 120VAC, 230VAC ; 50/60Hz (supplied AC mains depends on country requirements) - Power Consumption(1/8 power) V-3000 : 120VAC(12A), 230VAC(6A) V-4000 : 120VAC(14A), 230VAC(7A) - Weight : V-3000 : 11.7kg / 25.8lb, V-4000 : 11.8kg / 26lb - Dimension(W H D) : 482 88 407mm / 19 3.5 16in

Spec Rated Power RL=8 @ 0.1% THD (Stereo) RL=4 @ 0.1% THD (Stereo) RL=2 @ 0.5% THD (Stereo) RL=8 1kHz @ 0.1% THD (Bridged) RL=4 1kHz @ 0.5% THD (Bridged) Input Sensitivity (4) Input Impedance Slew Rate (8, Full Swing) Frequency Response (1W@8) Total Harmonic Distortion f=20Hz ~ 20kHz, 1/10 Power Signal to Noise Ratio Damping Factor (8, 1kHz) Residual Noise

Model 120VAC 550W 1000W 1600W 2000W 3200W

V-3000
230VAC 550W 1000W 1650W 2000W 3300W 0.95V 12 k (Balanced, Unbalanced) 120VAC 750W 1300W 2000W 2600W 4000W

V-4000
230VAC 750W 1300W 2100W 2600W 4200W 1.05V

20V/sec
20Hz~20kHz : -0.2dB, 10Hz~100kHz : -3dB <0.05% 105dB >400 73dBu >70dB 36.8dB 106dB

Channel Separation (1kHz, Half Power @8) Voltage Gain @4 (Gain SW 1V)

Power Amplifier

- Controls : Front : Power on/off switch, attenuator, LED indicator - Controls : Rear : Mode selector switch, Stereo/bridged mono switch - Connectors : Input : 1 XLR, 1/4 balanced per channel - Connectors : Output : 5-way binding post and SpeakonTM per channel - Indicators : Power : Green ; Protection : Red ; Clip : Red ; Signal : Green - Protection : Turn on delay, thermal, DC fault, PC limiter - Power Source : 100~120VAC or 220~240VAC ; 50/60Hz (supplied AC mains transformer depends on country requirements) - Power Consumption : R150PLUS : 170W (1.5A) - Power Consumption : R300PLUS : 250W (2.4A) - Power Consumption : R500PLUS : 480W (3.9A) - Weight : R150PLUS : 7.2kg / 15.9lb, R300PLUS : 8.4kg / 18.5lb - Weight : R500PLUS : 10.4kg / 23lb - Dimensions (W H D) : 482 88 317mm / 19 3.5 12.5in

Spec Rated Power

Model

R150PLUS
50W 75W 150W 170W

R300PLUS
100W 150W 300W 330W 0.775Vrms 10k (Unbalanced/20k balanced)

R500PLUS
170W 250W 460W 500W

at 8 @ 0.05 THD (Stereo CH) at 4 @ 0.05 THD (Stereo CH) at 8 @ 0.05 THD (Bridged mono) at 8 @ 0.5 THD (Bridged mono) Input Sensitivity (8, 1kHz) Input Impedance Slew Rate (8, Full Swing) Frequency Response (0.5dB) Total Harmonic Distortion f=20Hz ~ 20kHz, Half Power Signal to Noise Ratio Damping Factor (8, 1kHz) Residual Noise Channel Separation (8, 1kHz) Voltage Gain (4)

3V/sec
20Hz ~ 20kHz Less than 0.1% 100dB 100

-80dB
27dB 70dB 30dB 32dB

Professional & Commercial Audio Products

Professional Power Amplifier

- Controls Front : Power on/off switch, Attenuator, LED indicators Rear : Mode selector switch (Stereo/Bridged mono/Parallel), Gain selector switch,HPF off/30Hz/50Hz switch, Clip Limiter on/off switch - Connectors Input : Combination Jack (XLR Male or 1/4 TRS) Link : XLR Male Output : 5-Way binding post and SpeakonTM per channel - Indicators : Active(Green), -30dB(Green), -10dB(Green), Clip/Port(Red) - Protection Circuitry Full Short Circuit, Thermal Protection, Power ON/OFF Muting, DC Output Protection - Cooling : 2 variable speed fans, front to rear air flow - Power Source : 120VAC, 220VAC, 230VAC ; 50/60Hz (supplied AC mains depends on country requirements) - Power Consumption(1/8 power, RL=4) Q-3300 : 120VAC(12A), 220VAC/230VAC(6A) Q-4300 : 120VAC(14A), 220VAC/230VAC(7A) - Weight : 11.7kg / 25.8lb - Dimension(W H D) : 482 88 407mm / 19 3.5 16in

Spec Rated Power

Model 120VAC 550W 1000W 1600W 2000W 3200W 0.94V 1.00V

Q-3300
230VAC 550W 1000W 1650W 2000W 3300W 0.94V 1.00V 120VAC 750W 1300W 2000W 2600W 4000W 1.04V 1.14V

Q-4300
230VAC 750W 1300W 2100W 2600W 4200W 1.04V 1.14V

RL=8 @ 0.1% THD (Stereo) RL=4 @ 0.1% THD (Stereo) RL=2 @ 0.5% THD (Stereo) RL=8 1kHz @ 0.1% THD (Bridged) RL=4 1kHz @ 0.5% THD (Bridged) Input Sensitivity (4, gain sw:1V) Input Sensitivity (8, gain sw:1V) Input Impedance Slew Rate (8, Full Swing) Frequency Response (1W@8) Total Harmonic Distortion f=20Hz ~ 20kHz, 1/10 Power Signal to Noise Ratio Damping Factor (8, 1kHz) Residual Noise Channel Separation (8, 1kHz) Voltage Gain (4)

12 k (Balanced, Unbalanced)

20V/sec
20Hz ~ 20kHz : 0dBr 0.2dB, 10Hz~100kHz : +0 / -3dB <0.05% -105dB >400 -73dB : ATT min. >-70dB 36.8dB -106dB

Mixing Amplifier

- Amp Section : Rated Power : 2 x 150W @ 4 @ < 0.5% THD 1 x 300W @ 8 (bridged mono) @ < 0.5% THD Limiter to eliminate overload distortion - Preamp Section : Input : 5 x Line input Input : 2 x Mic input (mic1 has a Ducking function) Input : 2 Insert Output : REC out L/R Output : Master 2 out L/R Output : Master 1 mono sub out (low pass 100Hz/12dB) Output : 2 band equalizer (6dB Bass and Treble) Display : 2 x 5-Segment LED level meters for amp 1 and amp 2 2 x 1 LED for limit - Power Source : 100~120VAC or 220~240VAC ; 50/60Hz (supplied AC mains transformer depends on country requirements) - Power Consumption : 261W - Weight : 13kg / 28.6lb - Dimensions (W H D) : 483 88 382mm / 19 3.5 15in

Professional & Commercial Audio Products

Quad Amplifier

- Controls : Front : Power on/off switch, attenuator, LED indicator - Controls : Rear : Mode selector switch : Stereo/bridged, mono/parallel - Connectors : Input : XLR/1/4'Combination jack - Connectors : Output : 5-Way binding post - Indicators : Power : Red ; Protection : Red ; Clip : Red ; Signal : Green - Protection : Turn on delay, thermal, DC fault, PC limiter - Fan Speed : 50C(122F) ~ 60C(140F) Fan Speed : continuously-variable speed fan - Power Source : 100~120VAC or 220~240VAC ; 50/60Hz (supplied AC mains transformer depends on country requirements) - Power Consumption : QD4240 : 300W, QD4480 : 420W - Weight : QD4240 : 11.5kg / 25.3lb, QD4480 : 15.5kg / 34.2lb - Dimensions (W H D) : 482 88 369mm / 19 3.5 14.5in

Spec Rated Power

Model

QD4240
40W 60W 120W 0.775Vrms 20k (balanced/unbalanced)

QD4480
80W 120W 240W

RL=8 @ 0.05%THD (Per CH) RL=4 @ 0.05%THD (Per CH) RL=8 @ 0.05%THD (Bridged Mono) Input Sensitivity (8, 1kHz) Input Impedance Slew Rate (8, Full Swing) Frequency Response (0.5dB) Total Harmonic Distortion f=20Hz ~ 20kHz, Half Power RL=8 (Quad) RL=4 (Quad) RL=8 (Bridged) Signal to Noise Ratio Damping Factor (8, 1kHz) Residual Noise Channel Separation (8, 1kHz) Voltage Gain (4)

30V/sec
20Hz ~ 50kHz

0.05% 0.07% 0.07% 100dB 100

-70dB:ATT min.
80dB 26dB 29dB

Output Transformer Units

- OT-4240/4480 Transforms the 4 ohm output of the QD4240/4480 to 70V or 100V levels for use with high impedance speakers. - Expansion line out for QD4240/4480 - Weight : OT-4240 : 11.5kg / 25.3lb, OT-4480 : 14.5kg / 32lb - Dimensions (W H D) : 482x88x310mm / 19 3.5 12.2in - Dimensions (W H D) : 420x88x310mm / 16.5 3.5 12.2in - Dimensions (W H D) : w/optional rack-mount kit

Professional & Commercial Audio Products

88

310

Potrebbero piacerti anche