Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CONTENTS
1. PRECAUTIONS -----------------------------------------------------------------------------------------------------------------------2 1-1 SAFETY PRECAUTIONS ------------------------------------------------------------------------------------------------------------2 1-2 SERVICING PRECAUTIONS --------------------------------------------------------------------------------------------------------3 1-2-1 General Serving Precautions ------------------------------------------------------------------------------------------------3 1-2-2 Insulation Checking Procedure ---------------------------------------------------------------------------------------------4 1-3 ESD PRECAUTIONS ---------------------------------------------------------------------------------------------------------------4 2. REFERENCE INFORMATION ----------------------------------------------------------------------------------------------------5 2-1 COMPONENT DESCRIPTIONS-----------------------------------------------------------------------------------------------------5 2-1-1 DVD SANYO HD65 PUH----------------------------------------------------------------------------------------------------5 2-1-2 DVD Processor Chip MTK1389F ------------------------------------------------------------------------------------------7 2-1-3 Serial EEPROM, 2K (256 x 8) (24C02) or 16 K (2048 x 8) (24C16)------------------------------------------------ 22 2-1-4: FLASH MEMORY( CMOS 16M (2M 8/1M 16) BIT) ----------------------------------------------------------- 22 2-1-5 512K X 16 Bit X 2 Banks Synchronous DRAM (A43L0616) ---------------------------------------------------------- 25 3. PRODUCT SPECIFICATIONS -------------------------------------------------------------------------------------------------- 28 4. UPGRADING SYSTEM AND CHANGING THE REGION CODE------------------------------------------------------ 29 5. OPERATING INSTRUCTION ---------------------------------------------------------------------------------------------------- 30 MAINTENANCE & TROUBLESHOOTING --------------------------------------------------------------------------------------------- 30 6.DISASSEMBLY AND REASSEMBLY------------------------------------------------------------------------------------------ 32 7.TROUBLESHOOTING ------------------------------------------------------------------------------------------------------------- 33 8. BLOCK DIAGRAM ----------------------------------------------------------------------------------------------------------------- 34 9. CIRCUIT DIAGRAMS ------------------------------------------------------------------------------------------------------------- 35 10. WIRING DIAGRAM: -------------------------------------------------------------------------------------------------------------- 36
-1-
1. PRECAUTIONS
1-1 Safety Precautions
1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1) Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any remove for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. (2) Be sure that there are no cabinet opening through which adults or children might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover. (3) Leakage Current Hot Check-With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage. Current for Appliances and underwriters Laboratories (UL) 1270 (40.7). With the instruments AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially and exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test.
-2-
AC Leakage Test Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the customer. (4) Insulation Resistance Test Cold Check-(1) Unplug the power supply cord and connect a jumper wore between the two prongs of the plug. (2) Turn on the power switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all exposed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. When there is no return path to the chassis, the reading must be infinite. If the reading is not within the limits specified, there is the possibility of a shock hazard, and the instrument must be re-pared and rechecked before it is returned to the customer.
2) Read and comply with all caution and safety related notes non or inside the cabinet, or on the chassis. 3) Design Alteration Warning-Do not alter of add to the mechanical or electrical design of this instrument. Design alterations and additions, including but not limited to, circuit modifications and the addition of items such as auxiliary audio output connections, might alter the safety characteristics of this instrument and create a hazard to the user. Any design alterations or additions will make you, the service, responsible for personal injury or property damage resulting there from. 4) Observe original lead dress. Take extra care to assure correct lead dress in the following areas: (1) near sharp edges, (2) near thermally hot parts (be sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high voltage, and (5) antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring. Do not change spacing between a component and the printed-circuit board, Check the AC power cord for damage.
5) Components, parts, and/or wiring that appear to have overheated or that are otherwise damaged should be replaced with components, parts and/or wiring that meet original specifications. Additionally determine the cause of overheating and/or damage and, if necessary, take corrective action to remove and potential safety hazard. 6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, an ( ) or a ( ) on schematics and parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might created shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.
(3)
1-2-1 General Serving Precautions (1) a. Always unplug the instruments AC power cord from the AC power source before (1) removing or reinstalling any component, circuit board, module or any other instrument assembly. (2) disconnecting any instrument electrical plug or other electrical connection. (3) connecting a test substitute in parallel with an electrolytic capacitor in the instrument. b. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. c. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. d. Always connect a test instruments ground lead to the instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead
-3-
(4)
(5)
1-2-2 Insulation Checking Procedure Disconnect the attachment plug from the AC outlet and turn the power ON. Connect the insulation resistance meter (500V) to the blades of the attachment plug. The insulation resistance between each blade of the
attachment plug and accessible conductive parts (see note) should be more than 1 Megohm. Note: Accessible conductive parts include metal panels, input terminals, earphone jacks, etc.
-4-
2. Reference Information
2-1 Component Descriptions
2-1-1 DVD SANYO HD65 PUH
Connector Pin Definition
I/F Signals
FF+ T+ TC D CD/DVD RF A B F GND-PD VC VCC E NC VR-CD VR-DVD LD-CD MD HFM NC LD-DVD GND-LD
I/O Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
-5-
4. Block Diagram
Disc
MT1389 (Decode/Servo) ATAPI Buffer Manager Demodulator Error Correction PLI Focus & Tracking Loading
SDROM
Laser pickup
AuDdio AMP
Spindle Motor
Focus Coil
Track Coil
Sied Motor
-6-
2-1-2 DVD Processor Chip MTK1389F Features Super Integration DVD player single chip z High performance analog RF amplifier z Servo controller and data channel processing z Disc compatibility: DVD, DVD-R, DVD-RW, DVD+R, DVD+RW, Audio CD, CD-R, CD-RW, VCD, SVCD, MP3-CD, MP3-DVD, PCM, JPEG-CD, JPEG-DVD z Format compatibility:MPEG-1, MPEG-2, MPEG-4, DivX 3.11, DivX 4.x, DivX5.x (Need licence), Xvid, MP3, WMA, PCM, and JPEG & AVI Dolby Digital, DTS z Unified memory architecture z Versatile video scaling & quality enhancement z OSD & Sub-picture z 2-D graphic engine z Global motion compensation (GMC) z Quarter pixel accurate motion Compensation (Q-PEL) z B-frame z Higher bit-rate up to 10 Mbps z Full function remote control z Plays regional code encrypted (RCE) DVDs z Selectable 4:3 Pan & Scan or 16:9 Widescreen format z PAL & NTSC playback z Multi-speed FF/ RW, slow motion & multi level zoom High Performance Analog RF Amplifier z Programmable fc z Dual automatic laser power control z Defect and blank detection z RF level signal generato - Audio z Dolby Digital (AC -3)/EX decoding z DTS/DTS -ES decoding z MLP decoding for DVD-Audio z MPEG-1 layer 1/layer 2 audio decoding z MPEG-2 layer1/layer2 2-channel audio z High Definition Compatible Digital (HDCD) z Windows Media Audio (WMA) z Advanced Audio Coding (AAC) z Dolby ProLogic II z Concurrent multi-channel and downmix out z IEC 60958/61937 output -TV Encoder z Six 108MHz/12bit DACs z Support NTSC, PAL-BDGHINM, PAL-60 z Support 525p, 625p progressive TV format z Automatically turn off unconnected channels z Support PC monitor (VGA) z Support Macrovision 7.1 L1, Macrovision 525P z and 625P
-7-
* Pinout Diagram
-8-
PIN DESCRIPTON
-9-
- 10 -
- 11 -
- 12 -
- 13 -
- 14 -
- 15 -
- 16 -
- 17 -
- 18 -
- 19 -
- 20 -
- 21 -
2-1-3 Serial EEPROM, 2K (256 x 8) (24C02) or 16 K (2048 x 8) (24C16) 24C02 is used for DVD player while 24C16 is for DVD receiver. The capacity is the only difference between two kinds of serial EEPROM. Both of them use same package and have same pin configuration.
* Features z Low-Voltage and Standard-Voltage Operation -5.0 (V CC = 4.5V to 5.5V) -2.7 (V CC = 2.7V to 5.5V) -2.5 (V CC = 2.5V to 5.5V) -1.8 (V CC = 1.8V to 5.5V) z Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K) z 2-Wire Serial Interface z Schmitt Trigger, Filtered Inputs for Noise Suppression z Bi-directional Data Transfer Protocol z 100 kHz (1.8v, 2.5V, 2.7V) and 400 kHz (5V) Compatibility z Write Protect Pin for Hardware Data Protection z 8-Byte Page (1K, 2K), 16-Byte Page (4K, 8K, 16K) Write Modes z Partial Page Writes Are Allowed z Self-Timed Write Cycle (10 ms max) z High Reliability - Endurance: 1 Million Write Cycles - Data Retention: 100 Years - ESD Protection: >3000V z Automotive Grade and Extended Temperature Devices Available z 8-Pin and 14-Pin JEDEC SOIC, 8-Pin PDIP, 8-Pin MSOP, and 8-Pin TSSOP Packages * Pin Configurations
* Pin Description Pin Name A0-A2 SDA SCL WP NC Function Address Inputs Serial Data Serial Clock input Write Protect No Connect
to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29LV160TE/BE is programmed by executing the program command sequence. This will invoke the Embedded ProgramTM* Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is accomplished by executing the erase command sequence. This will invoke the Embedded EraseTM* Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margins. (Continued)
(Continued) Any individual sector is typically erased and verified in 1.0 second (if already preprogrammed). The device also features sector erase architecture. The sector mode allows each sector to be erased and reprogrammed without affecting other sectors. The MBM29LV160TE/BE is erased when shipped from the factory. The device features single 3.0 V power supply operation for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. A low VCC detector automatically inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ7, by the Toggle Bit feature on DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been completed, the device internally resets to the read mode. The MBM29LV160TE/BE also has a hardware RESET pin. When this pin is driven low, execution of any Embedded Program Algorithm or Embedded Erase Algorithm is terminated. The internal state machine is then reset to the read mode. The RESET pin may be tied to the system reset circuitry. Therefore, if a system reset occurs during the Embedded Program Algorithm or Embedded Erase Algorithm, the device is automatically reset to the read mode and will have erroneous data stored in the address locations being programmed or erased. These locations need re-writing after the Reset. Resetting the device enables the systems microprocessor to read the boot-up firmware from the Flash memory. Fujitsus Flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability, and cost effectiveness. The MBM29LV160TE/BE memory electrically erases all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word at a time using the EPROM programming mechanism of hot electron injection. *: Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc.
- 23 -
- 24 -
- 25 -
Pin Configuration
- 26 -
Block Diagram
Pin Descriptions Symbol CLk CS Name System Clock Chip Select Description Active on the positive going edge to sample all inputs Disables or Enables device operation by masking or enabling all inputs except CLK, CKE and L(U)DQM CKE A0~A10/AP BA RAS CAS WE L(U)DQM DW0-15 VDD/VSS VDDQ/VSSQ NC/RFU Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one clock + tss prior to new Clock Enable command. Disable input buffers for power down in standby. Row/Column addresses are multiplexed on the same pins. Address Row address: RA0 ~ RA10, Column address: CA0 ~ CA7 Selects bank to be activated during row address latch time. Bank Select Address Selects band for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK with Row address Strobe RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CLK Column Address Strobe with CAS low. Enables column access. Write Enable Enables write operation and Row precharge. Makes data output Hi-Z, t SHZ after the clock and masks the output. Data Input/Output Mask Blocks data input when L(U)DQM active. Data Input/Output Data inputs/outputs are multiplexed on the same pins. Power Supply/Ground Data Output Power/Ground No Connection
- 27 -
Power Supply: +3.3V0.3V/Ground Provide isolated Power/Ground to DQs for improved noise immunity.
3. Product Specifications
Playback System DVD Video Video CD (1.1, 2.0, 3.0) SVCD and CVD CDDA CD-ROM with MP3 data PICTURE CD Television Signal System NTSC/PAL Video Performance Video Out 1 Vpp into 75 ohm S-Video Out Y: 1Vpp into 75 ohm C: 0.286 Vpp into 75 ohm D/A Converter 27MHz/10bit Audio Performance Frequency Response Output Level D/A Converter S/N Ratio Connections Coaxial digital out Audio Analog out for 2-channel S-Video out Power Supply Power Source Power Consumption Set Dimensions (W X H X D) Net Weight Gross Weight AC 230V, 50Hz 15 Watt 360 X 45 X 270 (mm) 2.2 Kg 3.0 Kg X1 X1 X1
DVD VIDEO (PCM 96KHz) 20Hz~44KHz(1dB) DVD VIDEO (PCM 48KHz) 20Hz~22KHz(0.5dB) CD: 20Hz~22KHz(0.5dB)
- 28 -
- 29 -
5. Operating Instruction
Please refer to the Users Manual for the operating instruction of the system.
Maintenance & Troubleshooting
How to handle discs
To handle, clean and protect discs Do not touch the playing side of a disc
Some DVD discs may have special requirements for playing, with which this player may not be compatible. Please refer to specifications on individual disc.
DISC TYPE Content Size Total Play time About 2hrs. (Single side & single layer) About 4hrs. (Single side & double layer) About 4hrs. (Double side & Single layer) About 8hrs. (Double side & double layer) About 74 minutes About 300 minutes
Disc Compatibility
How to clean discs Finger prints and dust on surface can affect the sound and picture quality. Clean discs regularly with a soft cotton cloth from disc center to outside.
CD-DA MP3
AUDIO AUDIO
12CM 12CM
Discs types This DVD player can play the following types of discs: Discs other than listed above cannot be player by this player. This player uses NTSC/PAL color system. It cannot play discs recorded with other systems, such as SECAM. Region code The region code for this player is 5, which indicates the applicable. The disc with code number other than 5 cannot be player on this player and screen will indicate the unconformity. Copyright According to the related law, DVD discs without proper authorization are not allowed to be copied broadcast cable broadcast, played publicly or rented. As DVD discs are anti-piracy the copied content is distorted. TV system Connect this player to a PAL/NTSC compatible TV.
For sticky dust, wipe it with wet cloth and with dry cloth, Any kind of solvent, such as diluting agent, gasoline, liquid detergent, gasoline liquid detergent anti static aerosol used for vinylon LP, may cause disc damage.
Keep away from the direct sunshine or any heat source. Do not put discs in damp or dirty places, such as bathroom or near humidifiers. Store discs vertically in disc box and store in a dry place. Piling discs on to top of each other or excess weight load on disc box may cause the disc to warp.
- 30 -
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate the guarantee.
Problems No power indication No picture Cause Power plug not connected TV has not been set to the correct video input Video cable not firmly connected. Audio cable not connected tightly Power of audio apparatus is off Audio output setting is incorrect Disc is dirty Fast forward/backward activated Brightness unstable or noisy is Solution Plug the power cord into the power supply Set correct TV video input format for receiving the players output signals. Firmly insert the video cable ends to the related terminals. Firmly insert the audio cable ends to the related terminals. Turn on the power of audio apparatus. Setup audio output correctly via the setup menu. Take out the disc and clean. The picture may be distorted during fast forward /backward playback. Connect the player directly to TV. Load a disc. Load a compatible disc (Check the disc format and its colour system). Load a compatible disc (Check the disc format and its colour system). Check disc is put in correctly. Clean the disc. Change the setting via the setup menu. Disable this function or reset the rating level. Turn off the main switch or pull out the power plug, plug it in and turn on the power again. Point the remote control at the remote sensor.
No sound
Picture distortion
Affected by anti-piracy circuit No disc Disc not compatible The disc is placed upside down The disc not put in the tray correctly Disc is dirty Player setting are incorrect Parental lock is in effect Interference of power wave or other factors such as static interference The remote control not pointed at the remote sensor on the front panel of the player The remote control is out of specified range Battery power exhausted
Make sure the remote control range within 7 meters to the remote sensor. Replace with new batteries.
Note: This produce incorporates copyright protection technology that is protected by method claims of certain of certain U.S. patent and other intellectual Property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing users only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
- 31 -
- 32 -
7.Troubleshooting
Insert the AC power plug securely into the power outlet. Make sure that the equipment is connected properly. No picture Make sure that the input setting for TV is Video (AV). No sound Make sure that the equipment is connected properly. Make sure that the input settings for the TV and stereo system are Distorted sound correct. Some discs may have sections that prohibit fast forward or fast reverse. No fast forward or fast reverse Select the correct setup for TV aspect ratio that matches your TV set. No proper aspect ratio Check the batteries are installed with the correct polarities. Point the remote control unit at the remote control sensor and No operations can be performed operate. Remove the obstacles between the remote control unit and remote with the remote controller control sensor. Set the POWER button to OFF and then back to ON. No button operation Alternatively, turn off the power, disconnect the power plug and then reconnect it. If the audio soundtrack and /or subtitle language does not exist on Audio soundtrack and/or Subtitle the disc, the language selected at the initial settings will not be language is not the one you seen. selected. This function is dependent on software availability. Even if a disc No Angle change has a number of angles recorded, these angles may be recorded for specific scenes only. No power
- 33 -
8. Block Diagram
- 34 -
PLLVDD3
AVCC
APLLVDD3 AADVDD3
9. Circuit Diagrams
[1,2] V1P4 R42 10K E11 100U/16V C114 0.1U
DV33
V18
RFVDD3
R45 100K
R35
20P
C33 0.1U
RFVDD3
C24
C36
E17
100K
100K
C-3
0.1U C99
R49 15K
R51
R37
0.47U/NC
IOA [1]
10U/10V
Q7 3904
10K
0.047U
PLLVDD3
C29
R33
4.7 E8 47U/16V
R38 0 DVD_VR
R36 0
CD_VR
J5 SANYO_DU34 HD60-24SMD FOCFOC+ RAD+ RADC D LDSW RFO A B F GND4 V20 VCC2 E GND3 DVD_VR CD_VR CD_LD MDI VCC1 GND2 DVD_LD GND1 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (1) F(2) F+ (3) T+ (4) T(5) C (6) D (7) IOA (8) RFO (9) A (10) B (11) F (13) V20 (14) AVCC1 (15) E
AVDD3 IREF RFGC OSN OSP RFGND CRTPLP HRFZC RFRPAC RFRPDC RFVDD3 ADCVSS ADCVDD3 LPFOP LPFIN LPFIP LPFON PLLVDD3 IDACEXLP PLLVSS JITFN JITFO XTALI XTALO RFVDD18 RFGND18 ADACVDD2 ADACVDD1 ALF(CTR) ALS/SDATA0 AL/SDATA2 AVCM AR/SDATA1 ARS ARF(SW) ADACVSS2 ADACVSS1 APLLVSS APLLCAP APLLVDD AADVDD AKIN1 ADVCM AKIN2 AADVSS R/CR/CVBS/SY B/CB/SC DACVSSA G/Y/SY/CVBS DACVDDA DACVSSB DACVDDB CVBS DACVSSC
216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163
RFVDD3
C25
ADVCM
2SK3018 SPP11N60C3 Q9
C91 0.033U
C28
D SPP11N60C3 2SK3018 Q8
E28
G-1
S-2
Q6 8550 R34
4.7
E9 47U/16V RFV33
0.1U
E16
LDO2
C26 1000P
C32
1500P C90
RFV18
0.047U
D-3
10U/10V
L2 10uH
0.1U C98
B-1
E-2
ADACVDD3
0.1U C34
10U/10V
AKIN-1-2 R VB G CVBS
C109 NC
V20 [1]
(17) DVD_VR (18) CD_VR (19) LD_CD (20) MD11 (21) AVCC1 (23) LD_DVD 100U/10V E15 C106 0.1U
AVCC RFVDD3 600/0603 FB11 C105 0.1U [1] [1] E6 47U/10V C10 0.1U V2P8 V20 C9 0.1U OPOP+
[1,2]
V1P4
R27 R95 R97 R29 C81 0.1U C83 330P C3 330P [3] [3] [2]
10K 15K [2] TROPEN 18K 20K VSYNC# HSYNC# STBY V18
C5 0.015U
R31
[1,2]
V1P4
A2 A3 A4 A5 A6 A7 A8
R13 OP+ R12 150K R11 1 [2] DV33 SPOPR30 150K R32 C6 C8
680K 2200P
680K 2200P
OPO
IOA18 I0A19 IOWR# A16 HIGHA7 DVDD3 HIGHA6 HIGHA5 HIGHA4 HIGHA3 HIGHA2 HIGHA1 IOA20 IOCS# IOA1 I00E# AD0 AD1 AD2 DVSS AD3 AD4 AD5 AD6 IOA21 ALE AD7 A17 IOA0 DVDD18 UWR# URD# DVDD3 UP1_2 UP1_3 GPIO6 UP1_4 UP1_5 UP1_6 UP1_7 UP3_0 UP3_1 UP3_4 UP3_5 GPIO7 ICE PRST# IR INTO# DQMO# RD7 RD6 RD5 DVDD3
AGND DVDA DVDB DVDC DVDD DVDRFIP DVDRFIN MA MB MC MD SA SB SC SD CDFON CDFOP TNI TPI MDI1 MDI2 LDO2 LDO1 SVDD3 CSO/RFOP RFLVL/RFON SGND V2REFO V20 VREFO FEO TEO TEZISLV OP_OUT OP_INN OP_INP DMO FMO TROPENPWM PWMOUT1/ADIN0 TRO FOO FG/ADIN1 GPIO0/VSYNC# GPIO1/HSYNC# GPIO2 IOA2 DVDD18 IOA3 IOA4 IOA5 IOA6 IOA7 HIGHA0
U4 MT1389E
FS VREF DACVDDC SPDIF MC_DATA ASDATA3 ASDATA2 ASDATA1 ASDATA0 ALRCK ACLK ABCK GPIO5 DVSS GPIO4 GPIO3 DVDD18 RA4 RA5 RA6 RA7 RA8 RA9 RA11 CKE DVDD3 RCLK RA3 RA2 RA1 DVDD18 RA0 RA10 BA1 BA0 RCS# RAS# CAS# RWE# DQM1 RD8 RD9 DVSS RD10 RD11 RD12 RD13 RD14 RD15 RD0 RD1 RD2 RD3 RD4
162 FS 161 VREF 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
DACVDD3 [3] ASPDIF[3] RGB-SWITCH FS1 [2] FSO [2] ASDATA0 [1] MA[0:11][3]
[2]
C22 0.1U
R19 560
2.7uH L3
C37 1000P
TROUT [2] TRIN [2] LIMIT [1] MA4 MA5 MA6 MA7 MA8 MA9 MA11 DCKE[3] MA3 MA2 MA1 MA0 MA10 BA1 [3] BA0 [3] CS# [3] RAS#[3] CAS#[3] WE# [3] DQM1 [3] DCLK[3]
DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ0 DQ1 DQ2 DQ3 DQ4
DQ[0:15][3]
[1] JITFO
R39
750K
JITFN [1]
390P C30
C110 0.1U TRCLOSE [2] A21 A14 A13 A12 A11 A10 A9 A20 A18 A19 A16 A15 A17 A0 A1 R4 10K IOA
C111 0.1U
C27 0.1U
C93 0.1U
C95 0.1U
TO_AV/6P_2.0
6 5 4 3 2 1
[1]
A[0:21]
[3]
C97 0.1U DQM0 [3] URST# [1] SDA SCL [3] [3]
C113 0.1U
C107 0.1U
C88 0.1U
C89 0.1U
C96 0.1U
AD[0:7]
[3]
VCC
V2P8 V20
DV33
VCC [3] R21 10K C74 0.1U R10 10K DV33 J3 DOWNLOAD/4P_2.0 1 RXD 2 TXD 3 4 ASDATA0 [1] C77 NC C84 NC C101 NC R25 10 [3] [3]
R104 10K C92 0.1U E7 47U/10V C12 0.1U E10 47U/10V C11 0.1U D1 1N4148 URST# E5 100U/16V [1]
AD7
C4 100P
R7 0 OR NC VCC +12V -12V +12V J6 1 2 3 4 -12V [1] AL E30 10U/16V R63 10K
R68 30K
C51 2
C48 1000P
R71 5.1K
U9-A
D14 1N4148
R81 22K
AKIN-1-2 [1] FB25 RCH 7 E35 10U/16V [2] A_MUTE 3904 R84 560 Q14 [3]
R80 470
E38 100U/16V
E34 100U/16V
R70 30K
C52 6
100P
C49 1000P
R76 5.1K
U9-B
AUDIO_MUTE
DV33
TRB1 [2]
R14 0 OR NC
R69 30K
C123 2
E44 10U/16V
R67 10K
C69 1000P
R78 5.1K
[2]
U11-A
3904
R58 10K
[2]
REGO1 REGO2[2] R59 10K R64 10K R15 0 OR NC [1] ALS E41 10U/16V R41 10K R55 30K C68 2 C65 1000P R56 5.1K 3 100P E40 10U/16V A_MUTE R40 560
R62 10K
SCART
+12V R44 1K [3] R28 1K R47 75 ASPECT
[2]
U10-A
3904
R129 30K
C128 6
2.2K
Q1 3904
R48
2.2K
Q2 3904
R130 5.1K
[2]
U11-B
3904
FS1[1]
VCC
R18
R17 0 OR NC Q3 68 [3] 3906 R24 4.7K RGB-SW [1] ARS E26 10U/16V R60 10K
R57 30K
C47 6
C63 0.1U
C64 1000P
R22 5.1K
U10-B
U6 MO_VCC [1] [1] [1] [1] TT+ SL+ SL15 16 17 18 19 20 21 VOTK+ VOTKVOLD+ VOLDVCC2 NC VCTL VOFC+ VOFCVOSLVOSL+ VOTR+ VOTRVCC 14 13 12 11 10 9 8 F+ [1] F[1] SP[1] SP+ [1] LOAD+[2] LOAD- [2]
DV33
[2,3]
MO_VCC
R93 10K
J2 TRAY/5P_2.0 1 2 3 4 5
22 23 24 25 26 27 28 10K
7 6 5 4 3 2 1
TROPEN [1] TRCLOSE [1] [2] REGO1 DMSO [1] [2] REGO2 TRB1 [2] FOSO [1]
[2]
LOAD-
A[0:21] R1 WAITING TO DEBUG 16MFLASH R20 32MFLASH R20 R21 U2 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 [1] PRD# 25 24 23 22 21 20 19 18 8 7 6 5 4 3 2 1 48 17 16 9 10 28 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 G
[1] AD[0:7] [1] MA[0:11] [1,3] DQ[0:15] [1,3] KM416S1020BT MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 DBA0 SDCLK SDCKE A0 DCS# DRAS# DCAS# DWE# [1,3] [1,3] DV33 FB17 600/0603 C35 C1 0.1U 0.1U E4 100U/16V DQM0 DQM1
21 22 23 24 27 28 29 30 31 32 20 19 35 34 18 17 16 15 14 36 33 37 26 50 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 BS/A11 CLK CKE CS RAS CAS WE LDQM UDQM NC NC/VREF GND3 GND6 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 VCC1 VCC4 VCC2 VCC3 VCC5 VCC6 GND1 GND2 GND4 GND5 2 3 5 6 8 9 11 12 39 40 42 43 45 46 48 49 1 25 7 13 38 44 4 10 41 47
DQ[0:15] [1,3] MA[0:11] [1,3] U3 64MB_SDRAM 23 24 25 26 29 30 31 32 33 34 22 35 33X4 DBA0 DBA1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 SD33 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15A-1
29 31 33 35 38 40 42 44 30 32 34 36 39 41 43 45
U5
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
DV33
SD33 FB16 600/0603 100U/10V E12 0.1U C66 GND_D 0.1U C67 0.1U C70 0.1U C71 0.1U C72 0.1U C73 0.1U C7
MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 BA0 BA1 DCLK DCKE RN2
FB6
600/0603
20 BA0 21 BA1
SD33
FB10 600/0603 FB18 600/0603 FB19 600/0603 FB20 600/0603 FB21 600/0603 FB22 600/0603
BYTE (VPP)
47 13
[1] [1]
PCE# PWR#
12 RP 15 RB 26 E 11 W 14 (WP)
RN1
1 VCC1 14 VCC2 27 VCC3 3 VCCQ1 9 VCCQ2 43 VCCQ3 49 VCCQ4 6 VSSQ1 12 VSSQ2 46 VSSQ3 52 VSSQ4 28 VSS1 41 VSS2 54 VSS3
[1,3] [1,3]
DQM0 DQM1
GND_D
GND_D
GND_D
R1 R2
10K 10K
GND_D
VCC D4 DV33 ADACVDD3 FB12 600/0603 6800P C44 DV33 FB1 600/0603 6800P C87 VCC U1 24C02 1 A0 2 A1 3 A2 4 GND 8 VCC 7 WP 6 SCL 5 SDA R6 1K R9 1K L7 SCL SDA [1] [1] [1] G R74 75 C56 220P C60 100P DV33 R73 75 C55 220P C59 100P AADVDD3 [1] CVBS L6 L
BA99
CVBS0 [3] VCC [3] [3] [1] B/U R/V ASPDIF J10 1 2 3 4 5
220U/10V E25
1000U/10V E20
C43 0.1U
D7 1N4148 D6 1N4148
G/Y [3]
RFVDD3
[2,3] [2,3] [3] [2] [2] [3] [3] [3] [1] [1]
RCH LCH CVBS0 RGB-SW ASPECT R/V G/Y B/U HSYNC# VSYNC#
C20 2200P
C19 0.01U
12 11 10 9 8 7 6 5 4 3 2 1
J12
POWER CON
DV33 RFV33 FB15 600/0603 C40 0.1U E18 47U/16V +5V FB9 600/0603 C41 0.1U AVCC E19 220U/10V
RFV18
[3]
CVBS0
[3]
B/U
E24 47U/10V
E22 47U/10V
C94 0.1U
C31 0.1U
J11 AUDIO2 [2,3] VCC [2,3] L [1] VB R75 75 C57 220P L8 C61 100P D8 1N4148 D9 1N4148
LCH
4 5
RCH
SC
B/U [3]
[2]
LSCH
7 8
DV33 FB14 600/0603 E21 47U/10V MO_VCC VCC FB5 L 7 6 5 4 3 2 1 J7 FB4 L +5V +P12 -P12 FB23 FB24 L L C50 0.1U E32 C53 100U/16V 0.1U FB3 600/0603 +12V -12V
APLLVDD3
[2]
RSCH
C100 0.1U
220U/10V E14
C117 0.1U
100U/10V E23
[2] VCC [2] L5 L [1] X2 G1 NEW_PART1 X3 R72 75 2 1 2 C54 220P C58 100P R D3 1N4148 D2 1N4148
CENT
10 11
SUB
12 13 14
SY
R/V [3]
E37 100U/16V
VIDEO FILTER
Output to Amplifier
Output to TV
Transformer
Power
AV Output Board
Audio stream
Front Panel
- 38 -
Video stream
Power