Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Module 1
SOIL AGGREGATE (Lectures 1 to 4) Topics 1.1 INTRODUCTION 1.2 WEIGHT VOLUME RELATIONSHIP
1.2.1 Basic Definitions 1.2.2 General Range of Void Ratio and dry Unit Weight Encountered in Granular Soil 1.2.3 Relative Density and Relative Compaction
PROBLEMS REFERENCES
Module 1 Lecture 1 Soil Aggregate -1 Topics 1.1 INTRODUCTION 1.2 WEIGHT VOLUME RELATIONSHIP
1.2.1 Basic Definitions 1.2.2 General Range of Void Ratio and dry Unit Weight Encountered in Granular Soil 1.2.3 Relative Density and Relative Compaction
1.1 INTRODUCTION
Soils are aggregates of mineral particles, and together with air and/or water in the void spaces they form three-phase systems. A large portion of the earths surface is covered by soils, and they are widely used as construction and foundation materials. Soil mechanics is the branch of engineering that deals with the engineering properties of soil and its behavior under stresses and strains.
The weight of air is assumed to be zero. The volume relations commonly used in soil mechanics are void ratio, porosity, ad degree of saturation. Void ratio e defined as the ratio of the volume of voids to the volume of solids: (1.4) Porosity n is defined as the ratio of the volume of voids to the total volume: (1.5) Also, And so
(1.6) Degree of saturation as a percentage: is the ratio of the volume of water to the volume of voids and is generally expressed
The weight relations used are moisture content and unit weight. Moisture content w is defined as the ratio of the weight of water to the weight of soil solids, generally expressed as a percentage: (1.8)
Dept. of Civil Engg. Indian Institute of Technology, Kanpur 3
Unit weight
is the ratio of the total weight to the total volume of the soil aggregate: (1.9)
This is sometimes referred to as moist unit weight since it includes the weight of water and the soil solids. If the entire void space is filled with water ((i.e., ), it is a saturated soil; Eq. (1.9) will then give use the saturated unit weight . The dry unit weight is defined as the ratio of the weight of soil solids to the total volume: (1.10) Useful weight-volume relations can be developed by considering a soil mass is which the volume of soil solids is unity, as shown in Figure 1.2. Since from the definition of void ratio given in Eq. (1.4) the volume of voids is equal to the void ratio, e. the weight of soil solids can be given by
Where .
(1.11) The dry unit weight can also be determined from Figure 1.2 as (1.12) The degree of saturation can be given by (1.13) For saturated soils, . So, from Eq. (1.13), (1.14) By referring to Figure 1.3, the relation for the unit weight of a saturated soil can be obtained as (1.15)
Basic relations for unit weight such as Eqs. (1.11), (1.12), and (1.15) in terms of porosity n can also be derived by considering a soil mass that has a total volume of unity as shown in Figure 1.4. In this case (for V=1), from Eq. (1.5) , So,
(1.16) The dry unit weight is (1.17) If the soil is saturated (Figure 1.5). (1.18)
Several other functional relationships are given in Table 1.1 Table 1.1 Functional relationships of various soil properties for saturated soils Jumikis, A.R., Soil Mechanics, 1962, pp. 90-91, D. Van Nostrand Company, Inc., Princeton, New Jersy Sought quantities
Quantities and: Specific gravity Dry unit weight Saturated unit weight Saturated moisture content, % Porosity n Void ratio e
Part (b):From Eq. (1.14), for saturated soils, or From Eq. (1.15), the saturated unit weight is
1.2.2 General Range of Void Ratio and Dry Unit Weight Encountered in Granular Soils
The loosest and the densest possible arrangements that we can obtain from these equal spheres are, respectively, the simple cubic and pyramidal type of packing as shown in Figure 1.6. The void corresponding to the simple cubic type of arrangement is 0.91; that for the pyramidal type of arrangement is 0.34. In the case of natural granular soils, particles are neither of equal size nor perfect spheres. The smallsized particles may occupy void spaces between the larger ones, which will tend to reduce the void ratio of natural soils are compared to that for equal spheres.
(a)
(b)
Figure 1.6 Simple cubic (a) and pyramid (b) types of arrangement of equal spheres.
Table 1.2 Gives some typical values of void ratios and dry unit weights encountered in granular soils. Table 1.2 typical values of void ratios and dry unit weights for granular soils Dry unit weight Void ratio e Minimum ] Soil type Gravel Coarse sand Fine sand Standard Gravelly sand Silty sand Silty sand and gravel Maximum 0.6 0.75 0.85 0.8 0.7 1 0.85 Minimum 0.3 0.35 0.4 0.5 0.2 0.4 0.15 16 15 14 14 15 13 14 Maximum 20 19 19 17 22 19 23
Equation (1.19) can also be expressed in terms of dry unit weight of the soil:
The grain-size distribution can be used to determine some of the basic soil parameters such as the effective size, the uniformity coefficient, and the coefficient of gradation. The effective size of a soil is the diameter through which 10% of the total soil mass is passing ad is referred to as . The uniformity coefficient is defined as (1.23) Where is the diameter through which 60% of the total soil mass is passing. The coefficient of gradation is defined as (1.24) Where is the diameter through which 30% of the total soil mass is passing.
10
The uniformity coefficient and the coefficient of gradation for the sieve analysis shown in Figure 1.7. A soil is called a well-graded soil if the distribution of the grain sizes extends over a rather large range. In that case, the value of the uniformity coefficient is large. Generally, a soil is referred to as well graded if is larger than about 4 to 6 and between 1 and 3. When most of the grains in a soil mass are of approximately the same size i.e., is close to 1 the soil is called poorly graded. A soil might have a combination of two or more well-graded soil fractions, and this type of soil is referred to as a gap-graded soil. For fine-grained soils, the technique used for determination of the grain sizes is hydrometer analysis. This is based on the principle of sedimentation of soil grains. When soil particles are dispersed in water, they will settle at different velocities depending on their weights, shapes, and sizes. For simplicity, it is assumed that all soil particles are spheres, and the velocity of a soil particle can be given by Stokes law as (1.25) Where
In the laboratory, hydrometer tests are generally conducted in a sedimentation cylinder, and 50g of ovendried soil is used. The sedimentation cylinder is 18 in (457.2 m) high and 2.5 in (63.5 mm) in diameter, and it is marked for a volume of 1000 ml. a 125-ml solution of 4% sodium hexametaphosphate in distilled water is generally added to the specimen as the dispersing agent. The volume of the dispersed soil suspension is brought up to the 1000 ml mark by adding distilled water. After through mixing, the sedimentation cylinder is placed inside a constant-temperature bath. The hydrometer is then placed in the sedimentation cylinder and readings are taken to the tip of the meniscus (Figure 1.8) at various elapsed times. When the hydrometer is placed in the soil suspension at a time t after the start of sedimentation, it measures the liquid density in the vicinity of its bulb at a depth L (Figure 1.10). the liquid density is a function of the amount of soil particles present per unit volume of the suspension at that depth. ASTM 152Hydrometers are calibrated to read the amount in grams of soil particles in suspension per 1000 ml (for ). Also, at a time t the soil particles in suspension at depth L will have diameters smaller than those calculated by eq. (1.29), since the larger particles would have settled beyond the zone of measurement. Hence, the percent of soil finer than a given diameter D can be calculated. Since the actual conditions under which the test is conducted may be different from those for which the hydrometers are calibrated , it may be necessary to make corrections to the observed hydrometer readings. For further details regarding the corrections, the reader should refer to a soils laboratory manual (e.g.,Bowles, 1978).
11
12