Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Matter of time
1, the time back in 2000 : a: power- on operation, back in the running time of 2000, the general problem of the chip can be determined DS1307 b: time is running at normal power on until after the restart and found time to return in 2000 for two reasons , DS1307 damaged, or when power is not given DS1307 button battery powered . c: second jump, but 30 seconds is generally 32.768M boules exception. 2, the time to run fast or run slow : Normal years time , date and hour of the time there are deviations , usually 32.768KHZ crystal accuracy deviation , the need to replace the crystal . 3, the time has at some point , do not run in the past : Check the crystal welding is a problem, whether its the DS1307 1,2 PIN and to stick together , 1,2 PIN is stick together.
3. Audio issues
1, the audio is no output : a: NVP1114 audio output to the amplifier circuit coupling capacitor is damaged or missing Weld welding, resistance to change ; b: NVP1114 Weld , resulting in no communication with Hi3511 check NVP1114 related PIN pin connector is normal, there is no short or Weld welding problems , if re-welding can be ; c: amplifier circuit abnormalities , LM358 damaged, replace the LM358; 2, the audio sound is too small :
www.ttbvision.com
a: Check the LM358 surrounding circuitry , without exception , replace the LM358 can ;
4. Video issues
1 , a channel screen whitish a: the corresponding input channel matching capacitor is damaged, replace capacitors ; 2 , a channel no video output a: Q9 input signal is not sent over the seat , check the connections ; b: the corresponding input channel matching capacitor is damaged, replace capacitors ; c: the corresponding input channel 1114 or 1104 PIN feet short welding, or Weld, rewelding can 3 , a 2-way ( such as 3.4 ) does not stream, or sometimes flash when the image appears when the corresponding channel is off, when you want to access the video channel adjacent affected a: 33R matching exclusion stick welding , or damage to , or replacement can be heavy for exclusion ; b: 1114 or 1104 related to the output of PIN Weld or short welding , heavy for you can ; 4 , a 4-way ( such as 1-4 or 5-8 ) did not stream a: 54MHZ CLK signal is not over, matching resistor is damaged , replace damaged if the circuit can be, if 4 54MHZ crystal device checks whether there is not CLK output , if not, replace crystal ; b: for the corresponding channel chip 3.3V and 1.8V power anomalies , beads damaged, replace the beads ; 5, the monitor image dim a: 1114 VREF voltage supply is small, partial resistance of piezoelectric or capacitive NG, replace the capacitor or resistor to ; generally R1 exception. 6 Monitor output color bars , but can start a: 54M crystal oscillator is usually abnormal , replace 7 Monitor output color bars , but can not start General program exception , the program can be re- programmed
b: DDR initialization failed , 1.8V power anomalies , see specific veneer repair work instructions ; c: FLASH chip no program or programmer error, re- programming. 3 , after power , Flash lights off after the normal light , the system does not start : a: DDR initialization failed , 1.8V power anomalies , see specific veneer repair work instructions ;
7. Network problems
1, the network interface indicator is not lit , Rom Network: a: Check the network interface with the H1102 connected to the output level conversion is normal , check the H1102 operating voltage is normal, if abnormal replacement H1102; b: checking for RTL8201CL network chip power supply is normal , check the bead is damaged, and if so, replace ; c: Measuring the reset signal is normal , the chip RTL8201CL damaged, replace ;
8. PTZ problem
1 , PTZ inoperable a: Check the PTZ interface circuit connection is normal , usually chip 184 is damaged, you can replace ;
a: change the alarm input status , check sent to the GPIO level, measurement triode state , typically transistor Q1 is damaged, you can replace ;
www.ttbvision.com