Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SECTION
REAR AXLE
RAX
CONTENTS
PRECAUTIONS ..................................................... ..... 2 Precautions ......................................................... ..... 2 PREPARATION ...................................................... ..... 3 Commercial Service Tools ................................... ..... 3 NOISE, VIBRATION, AND HARSHNESS(NVH) TROUBLESHOOTING ........................................... ..... 4 NVH Troubleshooting Chart ................................ ..... 4 WHEEL HUB ......................................................... ..... 5 On-Vehicle Inspection and Service ...................... ..... 5 REAR WHEEL BEARING ................................ ..... 5 Removal and Installation ..................................... ..... 6 REMOVAL ........................................................ ..... 6 INSPECTION AFTER REMOVAL .................... ..... 7 INSTALLATION ................................................ ..... 7 SERVICE DATA AND SPECIFICATIONS (SDS) ... ..... 8 Wheel Bearing (Rear) .......................................... ..... 8
RAX-1
2004 Quest
CAUTION: q When installing each rubber part, the final tightening must be carried out under unladen condition* with tires on the ground. *Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions. q After installing the removed suspension parts, check the rear wheel alignment. q Do not jack up the vehicle at the trailing arm and lateral link.
RAX-2
2004 Quest
A
EDS000VV
PBIC0190E
RAX
RAX-3
2004 Quest
NOISE, VIBRATION, AND HARSHNESS(NVH) TROUBLESHOOTING NOISE, VIBRATION, AND HARSHNESS(NVH) TROUBLESHOOTING NVH Troubleshooting Chart
PFP:00003
EDS000VW
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
WT-3, "NVH Troubleshooting Chart" WT-3, "NVH Troubleshooting Chart" ROAD WHEEL
RAX-6
RAX-5
Reference page
Parts interference
RAX-5
Noise Shake Symptom REAR AXLE Vibration Shimmy Shudder Poor quality ride or handling : Applicable
RAX-4
2004 Quest
TIRES
A
EDS000VX
RAX
SMA525A
Check the axial end play. Axial end play : 0.05 mm (0.002 in) or less
q q
Check that the wheel hub bearing operates smoothly. Replace the wheel bearing assembly if the axial end play exceeds specification, or if the wheel bearing does not turn smoothly. Refer to RAX-6, "Removal and Installation" . CAUTION: The wheel hub assembly does not require maintenance. If any of the following symptoms are noted, replace the wheel hub assembly. q Growling noise is emitted from the wheel hub bearing during operation. q Wheel hub bearing drags or turns roughly.
RAX-5
2004 Quest
WDIA0111E
1. 4.
2.
Brake rotor
3.
REMOVAL
1. 2. Remove the rear wheel and tire using power tool. Remove the brake caliper assembly without disconnecting the hydraulic hose, using power tool. q The brake hose does not need to be disconnected from the brake caliper. q Suspend the caliper assembly using a wire so that the brake hose is not stretched. CAUTION: q Do not depress the brake pedal to prevent the caliper piston from popping out. q Do not twist the brake hose. Remove the brake rotor. NOTE: The parking brake must be fully released Remove the rear ABS sensor, then position it away from the hub assembly using wire. CAUTION: q Failure to remove the rear ABS sensor may result in damage to the sensor, causing the sensor to become inoperative. q Do not stretch the rear ABS sensor wire harness. Remove the wheel hub assembly from the knuckle using power tool.
3.
4.
5.
RAX-6
2004 Quest
WHEEL HUB
INSPECTION AFTER REMOVAL
Check for deformity, cracks, and damage on the wheel hub assembly, replace if necessary. CAUTION: The wheel hub assembly does not require maintenance. If any of the following symptoms are noted, replace the wheel hub assembly. q Growling noise is emitted from the wheel hub bearing during operation. q Wheel hub bearing drags or turns roughly.
A
INSTALLATION
Installation is in the reverse order of removal. q Check that the wheel bearing operates smoothly. q Check that the wheel hub bearing axial end play is within specification as shown. Axial end play : 0.05 mm (0.002 in) or less
RAX
G
LDIA0029E
RAX-7
2004 Quest
SERVICE DATA AND SPECIFICATIONS (SDS) SERVICE DATA AND SPECIFICATIONS (SDS) Wheel Bearing (Rear)
Axial end play 0.05 mm (0.002 in) or less
PFP:00030
EDS000VZ
RAX-8
2004 Quest