Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Pipe and types Pipe Fittings Wrought But welding and forging Flanges and Types Gaskets and its types Hardware Like Nut, Bolt and washer Piping System Material
Rajesh Kumdale inpac@rediffmail.com
Design Carbon steel, seamless Carbon steel, welded Line pipes Stainless steel, welded Precision steel pipes
In accordance with DIN EN 10220 / 10216-1 to 4 10220 / 10217-1 to 6 10220 / 10208-1 to 2 ISO 1127 / 10217-7 10305-1 to 5
BS EN 10255:
Specification For Seamless screwed and socketed steel tubes for plain end welding or for screwing to BS 21 corresponding types in BS 1387 and EN 10255.
Seamless steel tubes for pressure purposes EN 10216-1 Non-alloy steel tubes with specified room temperature properties EN 10216-2 Non alloy and alloy steel tubes with specified elevated temperature properties EN 10216-3 Alloy fine grain steel tubes EN 10216-4 Non-alloy and alloy steel tubes with specified low temperature properties EN 10216-5 Stainless steel tubes
DIN EN 10253-1
Butt-welding pipe fittings - Part 1: Wrought carbon steel for general use and without specific inspection requirements
DIN EN 10253-2
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection
DIN EN 10253-3
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements;
DIN EN 10253-4
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
DIN EN 10241
Specifies requirements for screw threaded fittings of nominal sizes from DN 6 to DN 150 inclusive, made out of welded steel or seamless steel tubes, forging and rolled bars. It is applicable to those screw threaded steel pipe fittings that are used in the transportation and distribution of liquid or gas.
Supplied in accordance with the basic specification. 1) Taper internal screw thread type Rc confirming to ISO 7-1 2) Parallel external screw thread type GA or GB conforming to ISO 228-1 3) Parallel internal screw thread type G conforming to ISO 228-1
DIN EN 10242 Threaded pipe fittings in malleable cast iron (British Standard)
Malleable iron pipe fittings, available in sizes from 1/8" to 6" PN25 rated. taper threads meet BS EN 10226-2 (ISO 7-1).
Bronze
Bronze pipe fittings sizes from 1/8" to 6" PN25 Taper threads meet (ISO 7-1). has very good resistance to corrosion by aggressive waters, steam and other fluids which
Slip-On Flange Weld-Neck flange Socket Weld Flanges Lap-Joint Flanges Groove & Tongue Flanges Blind Flanges
EN 1092-1:
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges This European standard specifies requirements for circular steel flanges in PN designations PN 2,5 to PN 400 and nominal sizes from DN 10 to DN 4000. This standard specifies the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange face surface finish, marking, materials, pressure/ temperature ratings and flange masses.
EN 1092-2:
Flanges and Their Joints - Circular Flanges for Pipes, Valves, Fittings and Accessories, PN Designated - Part 2: Cast Iron Flanges The document specifies requirements for circular flanges made from ductile, grey and malleable cast iron for DN 10 to DN 4000 and PN 2,5 to PN 63. It also specifies the types of flanges and their facings, dimensions and tolerances, bolt sizes, surface finish of jointing faces, marking, testing, quality assurance and materials together with associated pressure/temperature (p/T) ratings.
Gasket material which require low clamping force Gasket material which is capable to the fluid at temperature / s to be sealed Gasket material can withstand operating pressure
Rajesh Kumdale
Engineer Design-Piping inpac@rediffmail.com Pune- India