Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ISL85033EVAL2Z (Small Form) Wide VIN Dual Standard Buck Regulator With 3A/3A Output Current - Short Form
Description
The ISL85033EVAL2Z kit demonstrates performance of the ISL85033 switching regulator IC. An input range of 4.5V to 28V and 3A output per channel (connect in parallel to 6A) allows the ISL85033 to meet a wide variety of POL requirements. The ISL85033 is offered in a 4mmx4mm 28 Ld TQFN package with 1mm maximum height. The complete converter occupies 6.25cm2 area.
100 90 EFFICIENCY (%) 80 70 60 50 40 0.0 1.8VOUT 300kHz 0.5 1.0 1.5 2.0 OUTPUT LOAD (A) 2.5 3.0 12VOUT 1MHz 9VOUT 1MHz 5VOUT 500kHz 3.3VOUT 500kHz
Key Features
Wide Input Voltage Range from 4.5V to 28V Adjustable Output Voltage with Continuous Output Current up to 3A per channel Current Mode Control Adjustable Switching Frequency from 300kHz to 2MHz Independent Power-Good Detection Selectable In-Phase or Out-of-Phase PWMs Switching Operation Independent, Sequential, Ratiometric or Absolute Tracking Between Outputs Internal 2ms Soft-start Time Overcurrent and Hiccup Mode Short Circuit Protection, Thermal Overload Protection, UVLO Boot Undervoltage Detection Channels are Out-of-phase, Reducing Voltage Ripple and Component Size
1. Ensure correct board connection to the supply (+ to VIN1 and - to GND2) and loads prior to applying power, then turn on the power supply. 2. Verify the output voltage is 5V for VOUT1 and 3.3V for VOUT2.
Frequency Control
1.629 0.595
ISL85033 has an FS pin that controls the frequency of operation. Programmable frequency allows for optimization between efficiency and external component size. ISL85033EVAL2Z has the switching frequency set to 500kHz (FS is tied to VCC).
SYNC Control
The ISL85033 has a SI pin for external synchronization. Default board configuration has R8 = 0 to GND, which defaults to the internally selected switching frequency. Removing R8 allows the synchronization to be external between 600kHz to 4MHz. Do not leave this pin floating. ISL85033EVAL2Z board has VOUT1 set to 5V and VOUT2 set to 3.3V. The output voltage programming resistor, R3 (R10 respectively), will depend on the value chosen for the feedback resistor, R2 (R12 respectively), and the desired output voltage, VOUT, see Equation 1. The value for R2 (R12 respectively) is typically between 1k and 10k.
R 3 = ( V OUT1 V FB ) R 2 0.8 R 10 = ( V OUT2 V FB ) R 12 0.8 (EQ. 1)
Please note that if VOUT is less than 2.5V, switching frequency and compensation must be changed for 300kHz operation due to minimum on-time limitation. Please refer to data sheet FN6676 for further information.
November 29, 2010 AN1585.1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2010. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners.
SYNCIN
PGOOD2
PGOOD1 VCC
R13 DNP
NC1
R14 DNP A
VOUT1
28 27 26 25 24 23 22
VOUT2
COMP2
R1 0
C4
12PF R4
R3 42.2K
C6
COMP1
C1 68PF
C11 12PF R9
R10 25.5K
21
C13
A A
20 69.8K 470PF 19 18 17 16 15
FB2
C15 OPEN A R12 8.06K A GND4 A
VIN1
R15 0
VIN2
ISL85033IRTZ
SS2 BOOT2
C12 0.01UF
R2 8.06K A GND1
C2 OPEN A
BOOT1
C5 0.01UF A L1
5 6 7 29
U1
PHASE1 PHASE1 EP
PHASE2 PHASE2
VO1
VOUT1 VOUT1=5V
C3 47UF
8 9 10 11 12 13 14
L2
1 2
R16 DNP
FB2
7UH
VCC
SQL004
2
A
D1 B340B A
D2 B340B
7UH
SQL004
2
A
COMP1
R17 DNP
COMP2
VIN1
VIN1
C9 4.7UF A
VIN2
SS1
C10 10UF GND3 A A
R18 DNP
SS2
C7 10UF GND2 A A
C8 10UF A
SGND
IF VOUT1=5V (4.5V-5.5V) PLS POPULATE R26 IF VOUT2=5V (4.5V-5.5V) PLS POPULATE R27 OTHERWISE PLS LEAVE R26, R27 DNP!
R5 0 R6 0 R7 DNP
ONLY ONLY
1.500
1.875
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that the Application Note or Technical Brief is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com 2
AN1585.1 November 29, 2010