Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
050-200110
SERVICE MANUAL
COLOR TELEVISION
13A21
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note1] . 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 13 inch / 335.4mmV Normal 90 degree +0.45G/0.18G NTSC 1Speaker Bottom 3 Inch 8 ohm 1.0 W 0.8 W No US System M 1Tuner Ohers F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No No Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage 54 W at AC 120 V 60 Hz 5 W at AC 120 V 60 Hz -kWh/Year Yes UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less then 80% RH Yes Character Yes Yes Yes Yes Yes Yes No No No No No No Yes Yes Yes Yes Yes Yes No No No Yes Yes Yes Yes Yes Yes Yes No No No No No No Yes No Yes No Yes Yes Yes
G-2
Tuning System
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off CH Set Up TV/CABLE(CATV) Auto CH Memory Add/ Delete Language V-chip CH Label Favorite CH Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint (NTSC Only) Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Sleep Timer Sound Mute V-chip Rating
GENERAL SPECIFICATIONS
G-8 G-9 OSD Language Clock and Timer Sleep Timer OSD Language Setting Max Time Step Program(On Tim / Off Tim) English French Spanish English 120 Min 10 Min No No -Min Sec RC-EH No Toshiba 40-BF h 3V UM-4 x 2 pcs 27 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No No No No No No No No No No No No Yes Yes No Yes No No Yes Yes Yes USA,ORION Type No No No No No No No No No No No No Lines Yes No Yes No Yes No
G-10
Remote Control
G-11
Features
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than Unit Glow in Dark Remocon Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu Enter Mute Exit MTS(Audio Select) Set + Set Multi Brand Keys CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) Code FF Rew Rec Play Stop TV VCR Cable Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect Favorite CH
GENERAL SPECIFICATIONS
G-12 Accessories Owner's Manual Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Switch Front Power System Select Main Power SW Sub Power Channel Up/Reset Channel Down/Enter Volume Up/Set Up Volume Down/Set Down MENU=Volume Up+Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by On Timer Terminals Front Video Input Audio Input Other Terminal Rear Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Height (cm) Container Stuffing Cabinet Front Cabinet Rear No No No No No No No Yes No No No Yes UM4 x 2 No No No Yes Yes No No Yes No No No Yes Yes Yes Yes Yes No No No No Yes No No RCA RCA x 1 Ear Phone No No No No No No No No No No No F Type No 362 x 360 x 320.5 9.5 kg ( 20.9 lbs) 11.0kg ( 24.4lbs) No ---Sets -/--- x -- x -No Yes Double/Brown 440 x 408 x 380 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 62 866 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Language W/ Warranty English Yes Yes No
G-13
Interface
G-17
Cabinet Material
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
GND on the CRT Fig. 1-3 NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Fig. 1-1 Fig. 1-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.)
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Fig. 2-7
INIT CRT ON
00
83 0010
FIG. 1
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using SET + or - until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. The unit will now have the correct DATA for the new MEMORY IC.
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. Inferior silicon grease can damage IC's and transistors. When replacing IC's and transistors, use only specified silicon grease. Remove all old silicon before applying new silicon. Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
2. BASIC ADJUSTMENTS
2-1: RF AGC DELAY Place the set with Aging Test for more than 15 minutes. Receive a 63dB monoscope pattern. Connect the digital voltmeter to R606. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "RF AGC DELAY". 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.5 0.05V. 1. 2. 3. 4. 2-2: CUT OFF 1. Adjust the unit to the following settings. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64, B.BIAS=64, BRIGHTNESS=100, CONTRAST=64. 2. Place the set with Aging Test for more than 15 minutes. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 4. Adjust the Screen Volume until a dim raster is obtained. 2-3: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the adjustment control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select "R.BIAS". 5. Using the VOL. UP/DOWN button on the remote control, adjust the R.BIAS. 6. Press the CH. UP/DOWN button on the remote control to select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS". 7. Using the VOL. UP/DOWN button on the remote control, adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS. 8. Perform the above adjustments 6 and 7 until the white color is looked like a white. 2-5: SUB TINT/SUB COLOR 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP023. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line. (Refer to Fig. 2-1) 5. Connect the oscilloscope to TP022. 6. Press the CH DOWN button once to set to "COLOR" mode. 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110% of the white level. (Refer to Fig. 2-2) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~7.
TV
00 OSD
15 Fig. 1-1
2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments. NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 FUNCTION OSD H CUT OFF RF AGC DELAY VIF VCO H VCO H PHASE V SIZE V SHIFT R DRIVE B DRIVE R BIAS G BIAS B BIAS NO. 13 14 15 16 17 18 19 20 21 22 23 24 FUNCTION BRIGHTNESS CONTRAST COLOR TINT SHARPNESS FM LEVEL LEVEL SEPARATION 1 SEPARATION 2 TEST MONO TEST STEREO X-RAY TEST Fig. 1-2
ELECTRICAL ADJUSTMENTS
2-9: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) Fig. 2-1 TV
"A"
0% 00 OSD 110% A 100% Fig. 2-2 2-6: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H PHASE". 3. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-7: VERTICAL SIZE NOTE: Adjust after performing adjustments in section 2-6 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V SIZE". 3. Press the VOL. UP/DOWN button on the remote control until the rectangle on the center of the screen becomes square. 4. Receive a broadcast and check if the picture is normal. 2-8: VERTICAL SHIFT NOTE: Adjust after performing adjustments in section 2-7 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V SHIFT". 3. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask. 2-10: VIF VCO 1. Place the set with Aging Test for more than 10 minutes. 2. Receive an 80dB monoscope pattern. 3. Connect the digital voltmeter between the pin 5 of CP601 and the GND. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "VIF VCO". 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.5V. 2-11: SUB CONTRAST NORMAL 1. Activate the adjustment mode display of Fig. 1-1 press the channel button (14) on the remote control to select "CONTRAST". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "110". 3. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~3. 2-12: BRIGHTNESS 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRIGHTNESS". 2. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "96". 3. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~2. 4. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~2. B Fig. 2-3 15
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue colors. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
R G B RIGHT/LEFT SLANT
WEDGE
WEDGE
MAIN PCB
CRT PCB
BLOCK DIAGRAM
AGC
SDA
SCL
CHROMA IC IC601 M61206FP 32 X' TAL AUDIO OUT 50 62 RF AGC OUT 64 VIF IN (1) 1 VIF IN (2) IC351 AN7511 2 6 SOUND AMP IC SP351 8
11
SW
4 Q606
26 AD6/KEY2 POWER 27 AD5/KEY1 RED R 42 GREEN G 41 BLUE B 40 OS101 1 2 3 AT+5V OUT1/BLANK BL 39 10 INT1/REMOCON P50/H. SYNC P51/V. SYNC 1 2
REG
Q801 RED OUT Q802 GREEN OUT
UNREG + 12V
40 Y SW OUT 30 R IN 28 G IN 20 B IN 27 FAST BLK 12 INV FBP OUT 29 V PULSE OUT 5 SCL 10 SDA 42 MCU RESET 5 6 MEMORY IC SDA SCL IC199 S-24C02BDP-1A 52 EXT AUDIO IN 34 EXT C IN START UP VCC 19 H OUT 7 Q402 H. DRIVE Q401 H. OUTPUT
REG
20 XOUT 29 X-RAY
J703 1
Q503 PROTECT DRIVE Q504 FEED BACK 2
J702 1
2
T502 13
6
3 16 13 5 UNREG + 12V F501 2 1
L501
1 2 10 3
F S HV
AC IN
W001
J702 J703 W060 X101_1 OS101 W062 SW105 SW103 C128_1 C119 C121 W061 C124 C115 C130 W002 W003 D616 D615 R110 C601 W818 R641 W099 C603 C639 C637 W111 C417_1 R415 TU001 W106 C434 D403 D411 HS401 R416 IC401 W023 C403 D410 R418_1 R423 C604 R401 R445 C439 D406 W076 R002 D601 W097 Q402 C446_1 R446 D401 T401 D408 C440 Q401 R427 HS402 R405 R410 W837 C004 W806 D602 C623 W817 D001 D402 R421 R426 R606 C002 C632 R645 W010 W051 CF604 C003 R407 C435 R408 R404 W044 W029 W032 W031 W100 W028 W027 AGC D404 C427_1 CP601 W019 C406 C418 C407 W024 W070 C606 W015 W052 Q606 W011 L606 L607 C602_1 R618 L601 C624 CF601 R624 C609 C634 C625 W012 C636 C621_1 W014 W054 CF603 C627 B504 R518 C515 W046 W007 W008 R507 W101 W047 D516 R514 D514 D519 R523 R525 R524 Q507 R515 D605 C605 D611 C607 D613 C125 C613 C118 C129 C612 W042 D612 W105 W081 W018 W058 C134 W016 W004 W102 W005 IC199 W049 C122 W040 W809 R703 W835 W110 W813 SW102 R356 SW104 SW101 L101 W815
J352 D109
R805_1
4A125VOR250V
R701 R804 C356 C702 C355 C351 C642 IC351 W822 C647
S501A
_A_V
Q802
L801_1
TP024
Q801
TP022
R803_1 C352
CP802B
R802
FH501
C801
R807_1
R500_1
Q803
CD501_2
FH502
S501B C354
S101Y
F501
R806
TP023
W067 C819_1 C519_1 W057 D610 W017 X602 C638 Q603 CD351 W053 C630 W112
L501_1
CP806
W803 C516 C506 D510 2 1_ 52 C R613_1 W827 Q604 R623 C635 Q605 W816 C622 W103 W072 W078 C645
C503
TP004
TH501 TP003
D504
D505
C517
Q607
1 R517_
SOLDER SIDE
TP002 D503
C502
W079
R6 29
W013
CP502
R501
C526_1
Q502
D513
C501
Q503
W804
R505
D518
_ 14
04
R5
D509
C511
HS501 C443
W026
W074
C442_1
W107
D506
D512
D528
Q501
Q504
R511
C5
R510 R508
C520
R520
CP4
01
W069
FB401
R414
D405
R403
R409 C422
802
W833
01X
S1
CP
R417_1
C448
R4
29
W025
R413
C414
R115
W104
R132 R113
R129
R114 R131 R702 R116 R007 R119 R120 R123 R121 R124 R104 R102 R103 R122 R627 R630 R631 R626
R360
C805_1 R811 R815 C804_1 R809 R354 C806_1 R814 R359 R357 C353 R813 R353 R506 R512 R509 R513 R406 R419
R816
R605
IC601 49
R628
R633 R635
C626 C618
R634
R639
R611
R609
SOLDER SIDE
C655
R615 R622
R519
R602
R632
R620
C650
R617
R420
B
ACCESSORY
11 IF
TM101 RC-EH010
15
10
14
0 NC
0 NC
NC
1.3 NC 6.2 NC
4.9
4.8
30.0
4.8
0.022 F
C004
D001
C002
HZ30-3L
470 YK
12
7
FROM/TO CHROMA AGC GND W837
OS101 PIC-28143SY-2
6.3V
1 Vout
3 GND
TUNER+5V POWER LED D109 R002 R132 270 18K 1/2W R001 18K 1/2W IF
2 B+ 4.9
4.8
SLR-342VCT32
I2C_OFF VD MICON IC OEC7063A 42 RED R GREEN G BLUE B HD 3 R123 1 P50/H.SYNC P51/V.SYNC P00/EXT MUTE P01/I2C_OFF P02/AUDIO MUTE P03/(Surround) P04 4 4.0 41 2 4.7 40 3 0 39 4 4.8 5 0 0 7 0 P05/(Center_SP) P10/DEGAUSS_H INT2/P.FAIL INT1/REMOCON P23/SYNC P24 35 8 0 R114 10K R131 R115 100 W822 C140 100P SL 0.8 12 NC 0 NC 0 C122 50V 1 KA C121 200P C124 R129 1M 0.1 C130 0.01 Y 1 F 2 CH C120 R130 1K 1.9 16 V.HOLD CVIN CNVSS Xin Xout VSS 0.2 R134 17 560P W C138 470 2.6 18 0 19 AD6/KEY2 RESET OSC1 OSC2 VCC 26 4.8 25 50V 0.1 KA C115 2.5 24 3.3uH R127 L101 2.5 20 23 2.5 21 22 4.9 6.3V 100 YK 2.7K 4.9 15 HLF 31 SDA2 SCL1 SCL2 34 9 4.0 10 33 4.8 11 32 SDA1 4.8 NC 3.2 R007 4.8 NC 3.2 NC 0 0 28 0 27 W813 4.9 W815 R112 2.2K R113 2.2K C114 R119 RESET 1K W819 0.1 F C134 W835 R106 4.7K POWER R107 10K W809 SCL SDA AFT 270 C117 P21/AV1 P22/POWER 37 6 OUT1/BLANK BL P20/AV2 0 0 0 0 38 NC 0 NC 0 4.9 NC 0 R006 220P B R105 4.7K X-RAY C116 220P B FROM/TO CHROMA 270 FROM DEFLECTION/CRT +B POWER 4.7K R122 4.7K R121 4.7K R120 R102 R103 R104 4.7K 680 680 680 C125 50V 0.1 KA OSD_BLK R124 4.7K C129 50V 0.1 KA OSD_B C137 OSD_R 50V 0.1 KA OSD_G
IC101
R116
R117 47K
1K 1/4W
R110
5
FROM TV POWER X-RAY TO SOUND/AV AUDIO_MUTE
36
47K
13
14
0.001 Y
29
30
1 2
2.3 3 1.6 0
X101_1 EFOEC8004T4
AT+5V Y_VIDEO
0.1
4.8 5 SDA
4.8 6 SCL
0 7 MODE
SYNC
R128 R101
SW105 SKHVBED010 560 VOL DOWN R126 SW104 SKHVBED010 SW103 SKHVBED010 2.7K VOL UP 560
2
6.3V
C118 470 YK
SW102 SKHVBED010 CH UP
4 0 0
3 0
2 0
SW101 SKHVBED010
CH DOWN
POWER
VSS
E2
E1
E0
PCB010 TMA511
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
(MAIN PCB)
UNREG+12V 6 33 3W REG Q605 KTC3203_Y 7.2 4.9 5.5 REG Q606 KTC3203_Y 7.9 16V 47 YK 16V 47 YK 50V 1 KA C625 C630 R639 M C622 0.015 100 11.3 8.5 R629 REG Q604 KTC3203_Y 120 1/4W 4.9 7 7.2 5.5 R623
R622 L607
15uH
R635
C627
C650
W816
4.9
100P SL
50V 1
5.5
NA
8.8
CF604 TPSRA4M50C00-A0
100
C635
R633
68
8.2K
2.2uH
0.01 Y
R628
100
6
3.579545MHz X602 NC 0 3.0 2.2 48 47 46 49 FROM/TO SOUND/AV 5 AUDIO_OUT W806 C642 AUDIO_IN W827 GND 50V 1 KA C655 0.0068 Y C623 C632 R618 R632 MTZJ8.2B D602 220 10M 1/4W R634 R611 10K 10K C604 50V 1 0.0033 KA M 2.3 50 AUDIO OUT AUDIO BYPASS EXT AUDIO IN FM DIRECT OUT VIF VCO F/B VREG Vcc VIF APC FILTER VIF VIDEO OUT VIF GND CHROMA IC IC601 M61206FP VIDEO CHROMA Vcc V RAMP CAP AFT OUT QIF IN RF AGC OUT AFC FILTER H VCO F/B RF AGC FILTER VIF Vcc INV FBP OUT 64 VIF IN (1) 1 VIF IN (2) 17 V OUT 16 B OUT POWER ON CONT V RAMP FEEDBACK B IN STRAT UP Vcc 46 SW REG CONT 47 LIMITER IN 48 IF AGC 49 QIF OUT 2.4 51 2.2 52 3.0 53 2.9 54 3.2 55 8.7 56 16V 47 YK 50V 0.47 KA fsc OUT 3.2 57 22P SL C618 2.2 58 0 59 22 0 60 21 0.001 Y 1.9 61 2.8 62 4.6 63 SAW FILTER CF601 SAFGP45M7VHCZR IN IN G OUTOUT 1 2 3 4 5 2.9 64 1.5 1 1.5 0.01 Y C634 25 7.9 7.9 0 45 44 43 INTELLIGENT MONI Hi Vcc 0 42 MCU RESET 5.7 0 41 40 5.7V REG OUT(FOR CPU) Y SW OUT 5.6 0 39 38 5v REG 0 37 VIDEO/CHROMA GND 2.5 3.2 1.9 8.5 36 35 34 33 CHROMA APC FILTER TV/Y IN
6
C638 50V 4.7 KA
68K
R642 22K
D605 11E1-EIC
27
50V 2.2 KA
28 0 0 26 NC 7.0 NC 2.8 4.9 23 4.9 4.7 2.8 20 0 19 7.9 18 FROM/TO DEFLECTION/CRT 7.9 17 3.6 C612 10V 1000 YK W818 10 V_OUT ABCL V_FEEDBACK GND R641 22K +-1% C613 50V 1 YK C645 16V 47 YK W810
G IN
R609 C605
1SS133
D601
C624
470
0.01 Y
4
Y_VIDEO AT+5V SYNC TUNER+5V RESET AFT AGC IF 1.2uH L601
24
H OUT
R OUT
FBP IN
SCL
SDA
G OUT 12 13
DEF
V OUT
2 4.9
3 4.9 C639
4 0 0.01 Y
5 4.9 22K
6 0 R601
7 0 2.2K
8 0
9 0
R626
2K
H_OUT H_SYNC MTZJ12B C603 50V 1 KA R627 MTZJ12B R630 R631 2.2K 2.2K MTZJ12B R617 SWITCHING Q607 DTC114ESTP 0 4.9 D612 100 B.OUT 100 G.OUT 100 R.OUT 1K CLAMP 1SS133 D615 R620 1SS133 D616 1SS133 D613 12 TEST POINT CP601 173979-6 6 5 4 3 2 1
R602
1000 YK C637
470
0.01 Y
D610
0.01 Y
C601
R605
6.3V
4.7K
C607
R614
D611 2.2K
R619
GND
R625
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL AUDIO SIGNAL LUMINANCE SIGNAL TUNER VIDEO SIGNAL
G
PCB010 TMA511
8
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. POUR UNE PROTECTION CONTINUE LES RISQUES DINCEIE NUTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501).
TO SOUND/AV GND D505 470 YK R517_1 SOUND+B SB290S C516 500V 470P B C519_1 1.2 1W
16V
SOUND_GND
TO DEFLECTION/CRT B504 BL01RN1-A63 D510 +B RU2AM-EIC 160V 100 YXF C517 2KV 0.001 YR C521_2 UNREG+12V
CP502 TV-50P-02-A1
R500_1
1.2M 1/4W
500V 0.001 B
1N4005-EIC
1N4005-EIC
C505_1
275V 0.1
D504
D503
C503
C526_1
500V 0.001 B
200V 220 YK
R511 D509
C502
MTZJ18B
1.2M 1/4W
T502
81290264 10.0 10
1.7 NC 144.0 W804 NC 10.3 R504 3W SWITCHING Q501 144.0 D 2SK2662 G 4.8 0.1 S 6.6 R505 220 1W C509 1SS133 D508 0.047 M D512 10.3 1SS133
8 7 6 5 4 3 2
11 12 13 14 15 16 17
S501A
4
S501B
33
135.0
2KV 680P YR
C514_1
18 NC R523 D518 R512 1SS133 2.2K R520 11.5 M 4 0.01 10.5 1 150K 1/2W 47K
MTZJ15B
D507
R509
R506
0.68 1W
2.7K
3
R542
680
R508
1/4W
5.6K
1.5 2W
0 HS501 763WSA0005
C520
R515
1SS133 D519
2
910 1/4W
1SS133
D514
MTZJ5.6B
D528
2.2K +-1%
R518
PCB010 TMA511
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
A
FROM CHROMA
E
CP802A B2013H02-10P GND CLAMP G.OUT R.OUT B.OUT GND CLAMP G.OUT R.OUT B.OUT NC HEATER GND NC 180V 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 CP802B B2013H02-10P GND CLAMP G.OUT R.OUT B.OUT NC HEATER GND NC 180V GND CLAMP G.OUT R.OUT B.OUT NC HEATER GND NC 180V CP801 TBS-X01X-A1
CLAMP G.OUT R.OUT B.OUT V-OUT IC THERMAL PROTECTION + 1 3.5 2 25.0 C414 3 35V 100 YK 2.0 4 0 5 12.0 6 25.0 7 3.5 IC401 AN5522 PUMP UP
CD801_1
100uH 0305
1 L801_1
7
14
100.6 2.7
98.4 2.7
95.4 2.7
7
560 R816 R814 4.7K
R414
18 R423
C804_1 R809
C805_1 R811
11E1-EIC
100V 0.15 TF
330 1/2W
V801 A34AGT13X98(L) 9 10 8 6 11
C422
R420
25V 470 YK
R410
10K 1/4W
R417_1
1 1/2W
C418
R416
50V 10 YK
820
5 7 1
4.7K 1/2W
R413
R407
2.2 1/2W
HS401 763WSA0004
4.7K
3.3K
R415
R815
R G B
R813
4.7K
C806_1
100 1/4W
D403 19
470
R406
1K
TP022
TP024
TP023
R426
R429 4.7
15K +-1% 1W
AU02A-EIC
R405
R408
D411
2.7K 1/4W
R803_1
R805_1
15K 1W R802
15K 1W
D401
L405
D402 MTZJ11B
4.7mH 0909
TO MICON/TUNER X-RAY +B
MTZJ27B
R807_1
R804
R401
2.7K 1/4W
15K 1W R806
250V
1 YK
4.7K 1/2W
C437
68
NC 2 1
6 16 17
1/2W
C801
C439
330P B
4
FB401 3213012R HV FOCUS FOCUS SCREEN CP806 005P-2100 1 SCREEN C819_1 SCREEN 130.0 2KV 0.001 YR COL
500V 0.0022 B
50V 22 YK
C440
C446_1
100 1/4W
R427
B+
2KV 0.001 B
0.3
0 0
C442_1
27.0
130.0
H.OUTPUT Q401 2SD2627LS-CBC11 C443
132.5
VIDEO
6.4
4
96.4 0 F 1
0 NC 25.0
0
GND 8 E8 5 0 NC 6
101.6
99.6
MTZJ6.2B 56P SL D404 C407 J801 HPS3200-010501
D406 AU02A-EIC
D405
D410
AU02A-EIC
1SS133
W833
PCB110 TCA366
R445
200V 22 MHE 100V 0.1 MHE 35V 470 YK 220K 1/4W 11E1-EIC
180K 1/4W
C435
C403
C448
1
PCB010 TMA511
R421
D408
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
(MAIN PCB)
TO CHROMA 25
(FRONT)
AUDIO_IN
A_IN
VIDEO_IN
75 1/4W R702
C702
R701
47K
J702 AV1-09D-3
GND
VIDEO 2
V_IN
5
CD351 CH122301 SP OUT L+ SOUND GND 24 1 2 1 2 SP351 S08F21 8 OHM SPEAKER
SOUND+B GND 5
4
8.2 6 3.5 7 0 8 3.4 SOUND AMP IC AN7511 3.9 IC351
FROM MICON/TUNER R359 AUDIO_MUTE 47K C354 10V 2200 YK POWER 68K
4 5.1
3 0
2 0.3
3
R353
R360 68K
23
50V
16V 10 KA
KA
0.0015 Y
C351
R357
R354
100K
W803
270K
C353
C356
PCB010 TMA511
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
WAVEFORMS
MICON/TUNER
1 200mV 200ms/div
6 0.5V 20 s/div
11 1V 20 s/div
2 0.5V 20 s/div
7 500mV 20 s/div
12 1V 20 s/div
3 200mV 20 s/div
20V 20 s/div
13 1V 20 s/div
DEFLECTION/CRT
4 200mV 5ms/div
200mV 20 s/div
14 0.5V 5ms/div
CHROMA
5 0.5V 2ms/div
10 0.5V 5ms/div
15 20V 20 s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS
16 2V 20 s/div
21 50V 20 s/div
26 500mV 20us/div
17 200V 20 s/div
22 50V 20 s/div
SOUND/AV
18 10V 5ms/div
23 0.5V 1ms/div
19 10V 5ms/div
24 1V 1ms/div
20 50V 20 s/div
25 500mV 1ms/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
113
201
201 201
114
J801
109
201 102 114 L503 FB401 202 V801 114 203 TU001 114 PCB110 (CRT PCB)
108
203
111
202
205
104 106
SP351
105
101
Reference No.
A3J813A720 741WUA0019 713WPAA038 735WPA0396 701WPJB228 713WPAA039 735WPBA226 899HV3T000 702WPAA136 722549A018 800WQ00044 7230006755 726000A016 8121J50B54 8117540A64 8109630802 8109I30A04 8110630804 8110630A04 792WHAA052 792WHAA053 793WCDA987 A3J813A975 J3I70416 J3I70417 J3I70436 J3J81301 JB5UD400
Description
CABINET,FRONT ASSY SPRING,EARTH GLASS,LED SPEAKER HOLDER CABINET,FRONT GUIDE,REMOCON BUTTON,FRAME HOLDER,ANODE WIRE CABINET,BACK SHEET,RATING FELT SHEET SHEET,CAUTION SHEET,CRT SERVICEMAN SCREW,TAPPING(B0) GW20 SCREW,TAPPING(B0) TRUSS SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(P) BRAZIER PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX INSTRUCTION BOOK KIT IMPORTANT SAFETY INSTRUCTIONS REGISTRATION CARD ESP CARD INSTRUCTION BOOK POLY BAG
USA-TOSHIBA
BZ210013 BZ210023 AD300780 BZ210053 AD300037 BZ210114 AD300651 BZ210116 BZ210080 AD300782 AD300660 AD300783 AD300655 AD300656 AD300784 AD300602 AD300658 BZ210097 BZ210058 AD300660 BZ210099 BZ210099 BZ210099 AD300785 BZ110149 AD300662 BZ110041 AD300064 BZ110136 BZ110002 BZ110046 BZ110157 AD300664 BZ110080 BZ110080 BZ110145 AD300787 AD300787 AD300788 BZ110122 BZ110081 AD300077 BZ110081 AD300060 BZ110089 AD300078 AD300072 BZ410054 AD300069 AD300071 BZ410043 BZ410066 BZ410063 BZ410006 BZ410043 BZ410063 BZ410063 BZ410085 BZ410085 BZ410085 BZ410085 BZ410076 AD300670 AD300670 BZ410006 AD300671 BZ410080 BZ410006 BZ410076 BZ410006 BZ410006 BZ410006 BZ410006 BZ410021 BZ410006
Description
100K OHM 1/4W 18K OHM 1/4W 1K OHM 1/8W 2.2 OHM 1/2W 15K OHM 1/6W 12K OHM 1/6W 2.7K OHM 1/4W 4.7 OHM 1W 2.7M OHM 1/2W 5.6 OHM 5W 33 OHM 3W 220 OHM 1W 2.2K OHM 1/8W 68K OHM 1/2W 1.2 OHM 1W 2.2K OHM 1/6W 1.2K OHM 1/8W 1.5 OHM 2W 0.68 OHM 1W 33 OHM 3W 15K OHM 1W 15K OHM 1W 15K OHM 1W 2200 UF 10V 470 UF 35V 100 UF 35V 470 UF 25V 22 UF 100V 0.39 UF 250V PMS 0.001 UF 2KV BP 0.0082UF 1.6KV ECWH 22 UF 50V 22 UF 200V 0.001 UF 500V B 0.001 UF 500V B M 0.1 UF 275V PHE840 0.01 UF 250V 0.01 UF 250V 1 UF 50V 680 PF 2KV YR 470 UF 16V 0.001 UF 2KV YR 470 UF 16V 100 UF 160V 220 UF 200V 0.001 UF 2KV B HZ30-3L TD SLR-342VCT32 MTZJ27B T-77 MTZJ11B T-77 11E1-EIC MTZJ6.2B T-77 AU02A-EIC 1SS133T-77 11E1-EIC AU02A-EIC AU02A-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC SB290S MTZJ15B T-77 MTZJ15B T-77 1SS133T-77 MTZJ18B T-77 RU2AM-EIC 1SS133T-77 SB290S 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ5.6B T-77 1SS133T-77
CAPACITORS
! ! ! !
! ! ! ! ! ! ! ! ! ! ! !
DIODES
DIODE,ZENER LED DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON
! !
! ! ! ! ! ! ! ! !
! ! !
USA-TOSHIBA
BZ410058 BZ410043 AD300070 AD300070 AD300070 BZ410006 BZ410006 BZ410006 AD300672 AD300790 BZ611001 BZ611053 BZ611055 BZ510036 AD300791 AD300675 BZ510044 BZ510004 BZ410088 BZ510069 BZ510070 BZ510070 BZ510070 BZ510070 BZ510023 AD300794 AD300794 AD300794 AD300676 BZ310004 AD300677 AD300795 AD300678 BZ310009 BZ310043 BZ310041 BZ310080 AD300796 AD300797 AD300680 AD300681 BZ614004 BZ612001 BZ612001 BZ612001 BZ612001 BZ612001 AD300798 AD300799 BZ310016 AD300684 AD300685 AD300621 BZ613015 AD300686 BZ614020 BZ614018 BZ614135 AD300800 BZ614058 BZ614273 BZ614273 BZ614043 BZ614044 AD300688 BZ614111 BZ614005 BZ614005 BZ614171 AD300689
Description
MTZJ8.2B T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7063A S-24C02BDP-1A AN7511 AN5522 M61206FP 2SD2627LS-CBC11 2SC1473A-Q-TA ECT 2SK2662 2SC2120Y(TPE2) 2SA1624-AA LTV-817M-VB KTC3198-AT(Y,GR) KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT DTC114ESTP 2SC1473A-TA-(RQ) 2SC1473A-TA-(RQ) 2SC1473A-TA-(RQ) 3.3 UH 4.7 MH 1R5A102F20 8R140030 1.2 UH 2.2 UH 15 UH 100 UH 305Y001 81290264 HSJ1403-01-010 AV1-09D-3 AV1-09D-4 HPS3200-010501 SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 TMA511A TCA366A BL01RN1-A63T6 CH122301 0R414903 SAFGP45M7VHCZR EFCT4R5YS5A TPSRA4M50C00-A0 B05B-DVS TV-50P-02-A1 173979-6 TBS-X01X-A1 005P-2100 B2013H02-10P B2013H02-10P XRY16X28BD XRY20X30BD 51MS040LCC 3213012R EYF-52BC EYF-52BC PIC-28143SY-2 S08F21
ICS
IC IC IC IC IC
TRANSISTORS
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,FIELD EFF TRANSISTOR,SILICON TRANSISTOR,SILICON PHOTO COUPLER TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
! ! !
COILS &TRANSFORMERS
L101 L405 ! L501 ! L503 L601 L606 L607 L801 T401 ! T502 J352 J702 J703 ! J801 SW101 SW102 SW103 SW104 SW105 PCB010 PCB110 B504 CD351 CD501 CF601 CF603 CF604 CP401 CP502 CP601 CP801 CP806 CP802A CP802B EL001 EL002 F501 FB401 FH501 FH502 OS101 SP351
JACKS
JACK,RCA 3.5 RCA JACK RCA JACK SOCKET,CATHODE RAY TUBE
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT PCB ASS'Y PCB ASS'Y CORE,BEADS CORD,CONNECTOR CORD,AC BUSH FILTER,SAW FILTER,CERAMIC FILTER,CERAMIC TRAP CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER SPEAKER
! !
! !
USA-TOSHIBA
BZ410079 AD300690 BZ610125 BZ614141 AD300624 BZ613004
Description
ZPB45BL3R0A RC-EH010 TECC1040PG32D A34AGT13X98(L) EFOEC8004T4 HC-49/C