Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1-1
1 Hardware Overview
Chapter 1
1.1 1.2 1.3
Contents
Features ......................................................................................................................... 4 System Unit Block Diagram ......................................................................................... 8 TFT Color Display ......................................................................................................... 11 1.3.1 LCD Module .............................................................................................. 11
1.4 Power Supply .................................................................................................................. 12 1.5 Batteries ........................................................................................................................... 13 1.5.1 Main Battery............................................................................................... 13 1.5.2 Battery Charging Control ........................................................................... 14 1.5.3 RTC battery ................................................ Error! Bookmark not defined. 1.6 AC Adaptor ..................................................................................................................... 15
1-2
AT300/AT305/AT500
1 Hardware Overview Figures Figure 1-1 The front of the computer .................................................................................... 1-7 Figure 1-2 System unit block diagram .................................................................................. 1-8
Tables Table 1-1 LCD module specifications (1/1) ....................................................................... 1-11 Table 1-2 Power supply output rating ............................................................................... 1-12 Table 1-3 Battery specifications ........................................................................................ 1-14 Table 1-4 Time required for charges ................................................................................. 1-15 Table 1-5 RTC battery charging/data preservation time ................................................... 1-16 Table 1-6 AC adaptor specifications .................................................................................. 1-17
AT300/AT305/AT500
1-3
1 Hardware Overview
1.1
Features
The TOSHIBA AT300/Excite 10 AT300/Excite 10 AT305/REGZA Tablet AT500 Tablet PC uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage and high reliability. This computer incorporates the following features. Refer to the Parts List for the configuration of each model and the available options. Microprocessor The Avalon Tablet PC is equipped with a Nvidia Terga T30SL 1.3GHz. GPU (Graphics Processing Unit) (1) Graphic processor embedded) Memory On board RAM: DDR3L-1333 1GB Display 10.1W TFT panel 1280 x 800 Bootloader Boot Loader Kernel @ eMMC/ OS @ eMMC / Linux Kernel for Android 4.0 (Ice Cream Sandwich) Touch panel Capacitive multi touch screen support. Batteries The computer has one Detachable Prismatic 1S2P , 6600mAh,3.7V, 25Wh. Universal Serial Bus (USB2.0) USB ports is provided one Micro USB B type (USB Device 2.0). Storage Device EMMC Flash 16G /32G / 64G (BTO), 8G/128G design ready. Vibrator/ Haptics A vibrator is provided,
1-4
AT300/AT305/AT500
1 Hardware Overview Media Card slot The Media Card Slot can accommodate SD card slot push/push type. Media cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use Media Card flash-memory. Sound system The sound system is equipped with the following features: Codec WM8903 Amplifier: TI TPA2011D1 x 2 Built-in Speaker (1.5W) x 2 Built in microphone, HP/MIC Apple type combo jack Wireless LAN The computer is equipped with SDIO I/F on board type wireless LAN board that supports 802.11 b/g/n. Webcam Module 2M for front camera with LED, 5M for back camera and Flash LED SIM card slot (3G SKU only) A user accessible SIM card slot is provided behind battery. Bluetooth Module Bluetooth function integrated in WLAN module. G-sensor The PC is equipped with 3 axis accelerometer (G-sensor) E-compass This computer is equipped with an e-compass. GPS This computer is equipped with a GPS Gyro This computer is equipped with a Gyro
AT300/AT305/AT500
1-5
1 Hardware Overview Light-sensor This computer is equipped with a Light-sensor Proximity-sensor (3G SKU only) This computer is equipped with a Proximity-sensor
1-6
AT300/AT305/AT500
AT300/AT305/AT500
1-7
1 Hardware Overview
1.2
1-8
AT300/AT305/AT500
1 Hardware Overview The system unit is composed of the following major components: Processor Nvidia Terga T30SL 1.3GHz FCBGA 681 package
Sound Controller Wolfson WM8903LGEFK Mono Microphone-in and stereo headphone-out. (combo) Internal digital Microphone Volume control: volume up and down button control Stereo 4 ohm / 1.5W
EC/KBC (Embedded Controller/Keyboard Controller) One NUVOTON M0516LBN LQFP-48 chip functions as EC.
Wireless LAN One SDIO I/F on board used Support 802.11 b/g/n
Sensor
AT300/AT305/AT500
1-9
G-Sensor: KXTI9-1001 is used for screen orientation E-compass AKM AK8975B is used for e-compass. GPS BROADCOM/BCM47511IUBG is used for GPS Gyro MPU3050 is used for Gyro Light-sensor ISL29023 is used for Light-sensor Proximity-sensor (3G SKU only) IQS12800100TSR is used for Proximity-sensor
1-10
AT300/AT305/AT500
1 Hardware Overview
AT300/AT305/AT500
1-11
1 Hardware Overview
1-12
AT300/AT305/AT500
1 Hardware Overview
1.5 Batteries
The computer has one type of battery as follows: Main battery pack
The battery specifications are listed in Table 1-3. Table 1-3 Battery specifications
Battery name Main battery (1S2P) Material Li-ion Output voltage 3.7V Capacity 6600 mAh
1.5.1 Main Battery The removable main battery pack is the computers main power source when the AC adaptor is not attached. The main battery maintains the state of the computer when the computer enters into resume mode.
AT300/AT305/AT500
1-13
1 Hardware Overview 1.5.2 Battery Charging Control Battery charging is controlled by an embedded controller (EC). The EC controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. The system charges the battery. Battery Charge When the AC adaptor is attached, there are two types of charge: When the system is powered off and when the system is powered on. Table 1-4 lists the charging time required for charges. Table 1-4 Time required for charges
Battery type 1st battery pack Power on (hours) 8 hours max Power off (hours) 6 hours max
NOTE: The time required when the system is powered on is affected by the amount of power the system is consuming. Use of the fluorescent lamp and frequent disk access diverts power and lengthens the charge time. If any of the following occurs, the battery charge process stops. 1. The battery becomes fully charged. 2. The AC adaptor or battery is removed. 3. The battery or output voltage is abnormal. Detection of full charge A full charge is detected only when the battery is charging at charge. A full charge is detected under any of the following conditions: 1. The current in the battery charging circuit drops under the predetermined limit. 2. The charging time exceeds the fixed limit.
1-14
AT300/AT305/AT500
1 Hardware Overview
1.6 AC Adaptor
The AC adaptor is also used to charge the battery. Table 1-6 list the AC adaptor specifications. Table 1-6 AC adaptor specifications
Parameter Power Input voltage Input frequency Input current Output voltage Output current Specification 10W 100V-240V 50Hz60Hz 1.2A or less (100V-240V) 5V 0A to 2A (At constant voltage mode)
AT300/AT305/AT500
1-15
2-1
2 Troubleshooting Procedures
Chapter 2
Chapter 2 2.1 2.2 2.3 1
Contents
Troubleshooting Procedures ............................................................................................ 1 Troubleshooting ............................................................................................................ 5 Troubleshooting Flowchart ........................................................................................... 6 Power Supply Troubleshooting ................................................................................... 10 Procedure 2 Connection Check .......................................................................... 11 Procedure 3 Charge Check ................................................................................. 12 Procedure 4 Replacement Check........................................................................ 14 2.4 Main Board Troubleshooting ...................................................................................... 15 Procedure 1 Diagnostic Test Program Execution Check ................................... 16 Procedure 2 Replacement Check........................................................................ 17 2.5 Touch panel Troubleshooting...................................................................................... 18 Procedure 1 Diagnostic Test Program Execution Check ................................... 18 Procedure 2 Connector Check and Replacement Check .................................... 19 2.6 Display Troubleshooting ............................................................................................. 20 Procedure 1 Diagnostic Test Program Execution Check ................................... 20 Procedure 2 Connector Check and Cable Check ............................................... 20 Procedure 3 Replacement Check........................................................................ 21 2.7 Wireless LAN Troubleshooting .................................................................................. 22 Procedure 1 Transmitting-Receiving Check ...................................................... 22 Procedure 2 Antenna Connection Check ........................................................... 22 Procedure 3 Replacement Check........................................................................ 24 2.8 Sound Troubleshooting ............................................................................................... 25 Procedure 1 Diagnostic Test Program Execution Check ................................... 25 Procedure 2 Connector Check ............................................................................ 25 Procedure 3 Replacement Check........................................................................ 28 2.9 Card Reader Slot Troubleshooting .............................................................................. 29 Procedure 1 Check on Andriod .......................................................................... 29 Procedure 1 Connector Check and Replacement Check .................................... 29
2-2
AT300/AT305/AT500
2 Troubleshooting Procedures 2.10 Bluetooth (BTO) Troubleshooting .............................................................................. 31 Procedure 1 Diagnostic Test Program Execution Check ................................... 31 Procedure 2 SMT Check and Replacement Check ............................................ 32 2.11 Camera Troubleshooting ............................................................................................. 33 Procedure 1 Diagnostic Test Program Execution Check ................................... 33 Procedure 2 Connector Check and Replacement Check.................................... 34
AT300/AT305/AT500
2-3
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2)............................................................................. 7 Tables Table 2-1 Battery and DC in icon ............................................................................................ 9
2-4
AT300/AT305/AT500
2 Troubleshooting Procedures
2.1
Troubleshooting
Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1 Power Supply 2 Main Board 3 Touch panel 4 5 7 8 Display Wireless LAN Card reader board Bluetooth
6 Sound
9 Camera The Diagnostics tool operations are described in Chapter 3. Detailed Replacement Procedures are given in Chapter 4, Replacement Procedures. For tools required for executing the Test Program, refer to the Chapter 3. For tools required for disassembling/assembling, refer to Chapter 4.
AT300/AT305/AT500
2-5
2 Troubleshooting Procedures
2.2
Troubleshooting Flowchart
Use the flowchart in Figure 2-1 as a guide for determining which FRU is malfunctioning. Before going through the flowchart steps, check the following: Ask the user if a password is registered and, if it is, ask him or her to enter the password. Make sure that Toshiba released Operating System is installed, Non-Toshiba operating systems can cause the computer malfunction. Make sure all optional equipment is removed from the computer.
2-6
AT300/AT305/AT500
2 Troubleshooting Procedures
AT300/AT305/AT500
2-7
2 Troubleshooting Procedures
NO
YES
NO
YES
NO
Perform the appropriate procedure be outlined follow section to recover the error be detected by diagnostics
YES
Finish
2-8
AT300/AT305/AT500
2 Troubleshooting Procedures
If the diagnostics program cannot detect an error, the problem may be intermittent. The Running Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error, then perform the appropriate troubleshooting procedures as follows: 1. If an error is detected on the system test, memory test, real timer test, perform the Main Board Troubleshooting Procedures in Section 2.4. 2. If an error is detected on the touch panel test, perform the Touch panel Troubleshooting Procedures in Section 2.5. 3. If an error is detected on the display test, perform the Display Troubleshooting Procedures in Section 2.6. 4. If an error is detected on the Wireless LAN test, perform the Wireless LAN Troubleshooting Procedures in Section 2.7. 5. If an error is detected on the sound test, perform the Sound Troubleshooting Procedures in Section 2.8. 6. If an error is detected on card reader, perform the card reader Slot Troubleshooting Procedures in Section 2.9. 7. If an error is detected on Bluetooth, perform the Bluetooth Troubleshooting Procedures in Section 2.10. 8. If an error is detected on camera, perform the camera Troubleshooting Procedures in Section 2.11.
AT300/AT305/AT500
2-9
2 Troubleshooting Procedures
2.3
The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Icons in the LCD Check Procedure 2: Connection Check Procedure 3: Charge Check Procedure 4: Replacement Check Procedure 1 Icons in the LCD Check
The following Icons in the LCD indicate the power supply status: Battery icon The power supply controller displays the power supply status through the Battery and the DC IN icon in the LCD as listed in the tables below. To check the power supply status before power on, install a battery pack and connect an AC adaptor. Table 2-1 Battery and DC in icon
Battery icon Battery icon Doesnt light Power supply status DC in or DC and battery both in, Any condition other than those above.
2-10
AT300/AT305/AT500
2 Troubleshooting Procedures
Procedure 2
Connection Check
Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from the wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2. Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC-IN jack socket and AC adaptor inlet/wall outlet, respectively. If these cables are connected correctly, go to Check 3. Make sure the DC IN jack is firmly connected to the main board. If the DC IN jack is not firmly connected, go to Procedure 5. If it is connected, go to Check 4. Use a multi-meter to make sure the AC adaptor output voltage is close to 5 V. If the output is several percent lower than 5 V, go to Check 5. If the output is close to 5 V, go to Check 6. Connect a new AC adaptor or AC power cord. If the DC IN icon does not light, go to Procedure 5. If the battery icon does not light, go to Check 6. Make sure the battery pack is installed in the computer correctly. If the battery is properly installed and the battery icon still does not light, go to Procedure 3.
Check 2
Check 3
Check 4
Check 5
Check 6
AT300/AT305/AT500
2-11
The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack.
2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. Check 1 Make sure the AC adaptor and AC power cord is firmly plugged into the DC IN socket and the wall outlet. If these cables are connected correctly, replace the AC adaptor (and/or AC power cord, if necessary). Make sure the battery is properly installed. If the battery is properly installed, go to Check 3. The battery pack may be completely discharged. Wait a few minutes to charge the battery pack. If the battery pack is still not charged, go to Check 4. The batterys temperature is too hot or cold. Return the temperature to a normal operating condition. If the battery pack still is not charged, go to Check 5.
2-12
AT300/AT305/AT500
2 Troubleshooting Procedures
Check 5
Replace the battery pack with a new one. If the battery pack still is not charged, go to Procedure4.
AT300/AT305/AT500
2-13
The main board processor module may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. Check the connection between the AC adaptor and main board and connection. After checking the connections, perform the following Check 1: Check 1 Check 2 Replace the AC adaptor with a new one. If the AC adaptor is still not functioning properly, perform Check 2. Replace the main board with a new one following the steps described in Chapter 4, Replacement Procedures.
2-14
AT300/AT305/AT500
2 Troubleshooting Procedures
2.4
This section describes how to determine if the main board and CPU are defective or not functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. The procedures described in this section are: Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Replacement Check
AT300/AT305/AT500
2-15
2 Troubleshooting Procedures
Procedure 1
Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform these tests. a. Touch Test b. Key Pad Test c. AUDIO OUT Test d. AUDIO IN Test e. EXT AUDIO OUT Test f. EXT AUDIO IN Test g. CAMERA Test h. Multi-Touch Test i. HDMI Test (Both with & without Docking) j. Vibrator Test k. Temperature Test l. BT Test m. WIFI n. Docking Audio Test o. Docking HMDI Test p. Docking USB Test q. Check Docking Test r. Card Test s. Gyro Command Test t. u. Sensor Test Sensor Calibration
2-16
AT300/AT305/AT500
The main board connectors may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform Check 1. Check 1 Visually check for the following: a) Cracked or broken connector housing b) Damaged connector pins If their connectors are in good condition, but there is still a problem, go to Check 2. Check 2 The main board may be damaged. Replace the main board with a new one following the steps described in Chapter 4, Replacement Procedures.
AT300/AT305/AT500
2-17
2 Troubleshooting Procedures
2.5
To determine if the computers touch panel is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check
Execute the Touch panel in the Diagnostic Program. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform the test program. If an error occurs, go to Procedure 2. If an error does not occur, the Touch panel is functioning properly.
2-18
AT300/AT305/AT500
The touch panel board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the touch panel cable is firmly connected to the panel board. If the connection is loose, reconnect firmly. If there is still an error, go to Check 2.
Check 2
Check 3
The touch panel or the touch panel cable may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3 The main board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures.
AT300/AT305/AT500
2-19
2 Troubleshooting Procedures
2.6
Display Troubleshooting
This section describes how to determine if the computers display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Cable Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check
The Display Test program is stored on the computers Diagnostics USB key. This program checks the display controller on the main board. Connect the Diagnostics disk, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics for details. If an error is detected, go to Procedure 2. Procedure 2 Check 1 Connector Check and Cable Check
The LCD and Main board are connected by FPC cable. Make sure the FPC cable is firmly connected to Main board. If the connection is loose, reconnect firmly and restart the computer. If there is still an error, go to Check 2.
2-20
AT300/AT305/AT500
2 Troubleshooting Procedures
FPC Cable
Procedure 3 Replacement Check
LCD module and main board are connected to display circuits through FPC cable. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 The FPC cable may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 2. The Main board or LCD panel may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures.
Check 2
AT300/AT305/AT500
2-21
2 Troubleshooting Procedures
2.7
This section describes how to determine if the computers Wireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Transmitting-Receiving Check Procedure 2: Antenna SMT Check Procedure 3: Replacement Check Procedure 1 Transmitting-Receiving Check
Make sure the wireless switch of the computer is turned On. If it is not, please turn it on. Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test program. Check 1 Execute test program for the wireless LAN function to check the transmittingreceiving function of the wireless LAN. You will need a second computer that can communicate by the wireless LAN. If the computer passes the test, the function is correctly working. If the computer does not pass the test, perform Procedure 2. Procedure 2 Antenna SMT Check
The wireless LAN wiring diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the wireless LAN module is firmly mount to the main board.
2-22
AT300/AT305/AT500
2 Troubleshooting Procedures
If the wireless LAN module SMT fail, repair it firmly. If the wireless LAN is still not functioning properly, perform Check Procedure3.
AT300/AT305/AT500
2-23
The wireless LAN antenna, wireless LAN module and the main board are connected to the circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 The wireless LAN module may be defective or damaged. Replace the board with a new one following the steps in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 2. The wireless LAN antenna may be defective or damaged. Replace the antenna with a new one following the steps in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3. The main board may be defective or damaged. Replace the board with a new one following the instructions in Chapter 4, Replacement Procedures and test the display again.
Check 2
Check 3
2-24
AT300/AT305/AT500
2 Troubleshooting Procedures
2.8
Sound Troubleshooting
This section describes how to determine if the computers sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector & SMT Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check
Insert the Sound test program in the USB key, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for details. If an error is detected, go to Procedure 2. Procedure 2 Connector & SMT Check
AT300/AT305/AT500
2-25
2 Troubleshooting Procedures
Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: If the stereo speakers do not work correctly, perform Check 1. If the headphone does not work correctly, perform Check 2. Check 1 If the stereo speakers do not work properly, the speaker cable may be disconnected. Make sure the speaker cable is firmly connected to the Docking board. If the stereo speakers are still not functioning properly, go to procedure 3.
AT300/AT305/AT500
2-26
2 Troubleshooting Procedures
Check 2
If the headphone does not work properly, the headphone cable may be disconnected. Make sure the headphone cable is firmly connected to the Main board. If the sound function still does not work properly, go to procedure 3.
AT300/AT305/AT500
2-27
If the stereo speakers do not sound properly, the right or left speaker may be defective or damaged. Replace it with a new one. If the stereo speakers still do not work properly, go to Check 3. If the headphone does not sound properly, the headphone jack may be defective or damaged. Replace it with a new one. If the sound function still does not work properly, go to Check 3. The Main board may be defective or damaged. Replace it with a new one.
Check 2
Check 3
2-28
AT300/AT305/AT500
2 Troubleshooting Procedures
2.9
This section describes how to determine if the computers card reader functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Check on Android Procedure 2: Connector check and replacement check. Procedure 1 Check on Android
Insert SD card into the slot, check the data in the SD card can be read. If the card is not recognized or data are not read, go to Procedure 2. Procedure 2 Connector Check and Replacement Check
AT300/AT305/AT500
2-29
2 Troubleshooting Procedures
Check 1
The Card reader board and the Main board may be disconnected. Make sure the Card reader FPC is firmly connected to Main Board, if not, insert it firmly. If it still does not work, check the SD card inserted to the card slot on the Card reader board. If not, insert it firmly. If the SD card is still not functioning properly, perform Check 2. The SD card may be faulty. Replace it with a new one following the step in Chapter 4 Replacement Procedures. If the problem continues, perform Check 3. The Card reader board may be faulty. Replace it with a new one following the step in Chapter 4 Replacement Procedures. The Main board may be faulty. Replace it with a new one following the step in Chapter 4 Replacement Procedures.
2-30
AT300/AT305/AT500
2 Troubleshooting Procedures
Insert the Bluetooth test program in the USB key, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. If any errors occur while executing the Bluetooth test, go to Procedure 2.
AT300/AT305/AT500
2-31
The Bluetooth is installed on the Main board by BT/WIFI module. If the Bluetooth malfunctions, there may be a bad SMT between the Bluetooth and the Main board. Or the Bluetooth IC or Main board could be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the BT/WIFI module mount on the main board. If BT/WIFI module SMT is fail, repair it firmly and repeat Procedure 1. If the Bluetooth is still not functioning properly, perform Check 2. Check 2 The Bluetooth may be defective or damaged. Replace BT/WIFI module with a new one following the steps in Chapter 4, Replacement Procedures. If the Bluetooth is still not functioning properly, perform Check 3. The main board may be defective or damaged. Replace it with a new one following the steps in Chapter 4, Replacement Procedures.
Check 3
2-32
AT300/AT305/AT500
2 Troubleshooting Procedures
Insert the camera test program in the USB key, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. If any errors occur while executing the camera test, go to Procedure 2.
AT300/AT305/AT500
2-33
The camera is installed on the switch board by camera cable. If the camera malfunctions, there may be a bad connection amount of camera, switch board or Main board. Or the Switch board to main boards FPC or the camera cable might be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the camera is firmly connected to the Switch board by camera cable & check Switch board to Main boards FPC is firmly.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the camera is still not functioning properly, perform Check 2. Check 2 The camera may be defective or damaged. Replace it with a new one following the steps in Chapter 4, Replacement Procedures. If the camera is still not functioning properly, perform Check 3. The camera cable may be defective or damaged. Replace the camera cable with a new one following the steps in Chapter 4, Replacement Procedures. If the camera is still not functioning properly, perform Check 4. The Switch board may be defective or damaged. Replace it with a new one following the steps in Chapter 5, Replacement Procedures. The main board may be defective or damaged. Replace it with a new one following the steps in Chapter 4, Replacement Procedures.
Check 3
Check 4
Check 5
2-34
AT300/AT305/AT500
AT300/AT305/AT500 3-1
Chapter 3 Contents
Tests and Diagnostics .............................................................................................................. 3 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.2 3.2.1 3.2.2 3.2.3 3.3 3.3.1 3.4 3.4.1 3.4.2 3.5 SOFTWARE INSTALL ............................................................................................. 5 Recovery Mode: ....................................................................................................... 5 First Use Setting....................................................................................................... 8 Sleep Time Setting ................................................................................................. 13 ADB Driver ............................................................................................................ 16 Program Install and Test.......................................................................................... 21 APK Install............................................................................................................. 21 Test items................................................................................................................ 24 Other functions of diagnostic tool ........................................................................ 51 T&D VERSION UPDATE ....................................................................................... 55 T&D version Update ............................................................................................. 55 DMI Tool Install and Use ......................................................................................... 58 Tool Install ............................................................................................................. 58 DMI Modify ........................................................................................................... 60 Appendix .................................................................................................................... 63
3-2 AT300/AT305/AT500
2The T&D folder contains these four files, we need to realize the usage:
The debug mode driver Firmware copy to SD card To install the software Test Menu Command
The FW folder contains shipping image of each region. Please copy the correct image to SD card what you need. And then plug SD card to tablet PC before start Recovery mode.
AT300/AT305/AT500 3-3
Note:
z z The tablet PC should be tested with Win-7 of 32 bit (exclusive of the 64 bit). The OS before will be covered completely after you do as following, please be careful with it.
3-4 AT300/AT305/AT500
(a) Before enter the recovery mode, you must make sure that the AC adapter has been plugged to the Tablet to ensure that system will not power down. (b) Press and hold vol+ key, then press and hold power key about 3 seconds, the tablet PC will shake.
AT300/AT305/AT500 3-5
Vol-
Vol+
power
(c) Now the Tablet PC will display below picture on the screen. Press vol- key then press power key to select left icon to enter the recovery mode.
(d) Then the screen will display as below. Press Vol- key then press power key. Select apply update from external storage
3-6 AT300/AT305/AT500
AT300/AT305/AT500 3-7
(e) Then the screen will show as below. Press Vol- key or Vol+ to select then press power key. Select corresponding image to flash.
It will take about 5 minutes. When it finished, the tablet pc will restart and go to First Use.
3-8 AT300/AT305/AT500
AT300/AT305/AT500 3-9
3-10 AT300/AT305/AT500
AT300/AT305/AT500 3-11
3-12 AT300/AT305/AT500
AT300/AT305/AT500 3-13
3-14 AT300/AT305/AT500
AT300/AT305/AT500 3-15
3-16 AT300/AT305/AT500
(c) Click the item Update Driver Software to install driver for Android
AT300/AT305/AT500 3-17
3-18 AT300/AT305/AT500
Now, please rescan the Computer Management to ensure that you have found the item PEGATRON Android Composite ADB Interface under the index Android Devices.
Here inform us that the debug mode has been installed OK.
AT300/AT305/AT500 3-19
You should rescan the Device Manager to make sure you have already found the tablet. Then jump to do the step (b).
3-20 AT300/AT305/AT500
AT300/AT305/AT500 3-21
3-22 AT300/AT305/AT500
By the way, the first time you get in the application, you may got an interface like below, just press the OK button skip it.
AT300/AT305/AT500 3-23
Note: All the items in the Diagnostic Tool has been shown in the below picture. What you need to do is to test all one by one.
3-24 AT300/AT305/AT500
(a) Press the icon Wi-Fi, and the program will search the router which can be connected automatically.
After you test this function and passed, the Touch Test icon will be green as below picture. (All the icons will turn to green like this after function test passed)
(b) Press this icon Bluetooth, the program will detect Bluetooth device automatically.
AT300/AT305/AT500 3-25
3-26 AT300/AT305/AT500
(c) Press the icon Accelerometer to test the accelerometer sensor, pick up and shake the tablet PC. If the value of x, y, z changes with shaking, the program will show pass automatically.
(d) Press the icon Orientation to test the orientation sensor, pick up and shake the tablet PC. If the value of Azimuth, Pitch, Roll changes with shaking, the program will show pass automatically.
AT300/AT305/AT500 3-27
(e) Press the icon Magnetic Field to test the magnetic field sensor, pick up and shake the tablet PC. If the value of magnetic_x, magnetic_y, magnetic_z changes with shaking, the program will show pass automatically.
3-28 AT300/AT305/AT500
(f) Press the icon Temperature to test the CPU temperature sensor. If there is value detect, the program will show pass automatically.
(g) Press the icon Light to test the light sensor. Use something to shelter the ALS light sensor (right beside the front camera), the value of light will change. Then the
program will pass automatically.
AT300/AT305/AT500 3-29
3-30 AT300/AT305/AT500
(h) Press the icon GyroScope to start the gyroscope test. If the value of x, y, z changes with shaking, the program will show pass automatically.
AT300/AT305/AT500 3-31
(i) Press the icon GPS, program will test the GPS function with NMEA sentences, and if the GPS function is OK, this test will be finished in 20 seconds.
3-32 AT300/AT305/AT500
(j) Press the button Battery, this item will be passed only if the adapter is plugged in and charging or the device is fully charged. So please plug the adapter before this test.
(k) Press this icon Touch panel, the screen will show many spaces, and these spaces will be changed green after one finger touch them. The tester need use the finger to touch all the spaces slowly, or this item will not pass. If there is one or some spaces always can not be changed, it means the test fail.
AT300/AT305/AT500 3-33
(l) Press the icon Multi-Touch, you need simultaneously touch the screen with all ten fingertips, and the screen will show the values of the location where you touching.
3-34 AT300/AT305/AT500
Around 2 seconds, the program will show as below, then remove your fingers and press OK to pass this test. If the test dont show finished as below, it means the test fail.
(m) Press this icon Touch Accuracy; user should paint a rectangle which is similar to rectangle in the screen within the scope of the error using a continuous series of
AT300/AT305/AT500 3-35
curves. (one small block is allowed around left, right, forward and back)
(n) Press the Volume buttons, to check the buttons function whether OK.
3-36 AT300/AT305/AT500
When you press the volume down button, the screes will show Volume Down: Pass as below. If both the up and down button working well, this item will be passed automaticlly.
AT300/AT305/AT500 3-37
(o) Press the icon LCD+Brightness to test the color and brightness.
When white, blank and gray test ok the screen will shows as blow, press pass to test next function.
3-38 AT300/AT305/AT500
Then the screen will show 3 color (red, green, and blue), then press the button to end the LCD+Brightness test.
AT300/AT305/AT500 3-39
3-40 AT300/AT305/AT500
(p) Press icon Audio out to test audio function, you will maybe hear a sound which calls zero, one, two, three or four. If user can hear the voice, it represents the audio output is normal. When user presses the right number of button which user just heard. Both tests of right sound channel and left sound channel are successful.
AT300/AT305/AT500 3-41
(q) Press the Audio in icon to test the audio in function (record), the screen will show as below, after you press OK, you will be asked to record your voice for 3 seconds. Then, your audio recording will be replayed. If you can hear the audio clearly, press pass button to finish this test.
3-42 AT300/AT305/AT500
(r) Press the External Audio out icon to test the external audio out function, the process same as the audio out test, but need you plug one earphone (with Mic function).
AT300/AT305/AT500 3-43
3-44 AT300/AT305/AT500
(s) External Audio in test, also record your voice and replay to you. Just need plug the earphone (with Mic function).
AT300/AT305/AT500 3-45
3-46 AT300/AT305/AT500
(t) Press the Back Camera button to test the back camera function, press the capture button, if you see no difference between the camera shows and you captured, press pass, otherwise, press fail.
AT300/AT305/AT500 3-47
(u) Press the Front Camera button, then the device will take a picture by front camera automatically. Press Pass if you can see the same picture.
3-48 AT300/AT305/AT500
(v) Press the HDMI icon to test the HDMI function, if the video played normally, press pass to finish this item.
(w) Press the Vibration icon, then system will begin to vibrate the device. If you can experience the built-in vibration. Press Pass to finish this item.
AT300/AT305/AT500 3-49
3-50 AT300/AT305/AT500
(b) Batch Test: The batch test will test other items, different as auto test, these items need user to operate on the screen. Such as Touch panel, Multi-Touch Also, press yes to start batch test.
AT300/AT305/AT500 3-51
(c) Summary: You can see the test report by this icon, like below shows.
(d) Clear Report: As above shows, these buttons will turn green or red after user test them, if you want reset them, please press this button.
3-52 AT300/AT305/AT500
(e) Device Information: User can see the device information by this function, PPID, Mac Address, Android version
AT300/AT305/AT500 3-53
(f) About/ Help: Press the About/ Help button, the system will simply introduced this tool.
(g) Exit:
We can close this tool by the Exit button.
3-54 AT300/AT305/AT500
AT300/AT305/AT500 3-55
Second, click the icons Diagnostic Tool to enter the surface of uninstall.
Then press the option Uninstall and there will popup the massage window. Here we should click OK. (Also if you now just not want to do the version update, you should press Cancel)
3-56 AT300/AT305/AT500
After you uninstall the program successfully, you will got the below message.
(c) Then you can install the new Diagnostic Tool in order to test the tablet.
AT300/AT305/AT500 3-57
(b) Install the APK program, get in C:\avalon, run the CMD avalon.bat and then select item 3 in the below picture. After the APK be installed successfully, the success will be shown in the screen.
3-58 AT300/AT305/AT500
(c)
AT300/AT305/AT500 3-59
(a)
Press Modify before each item to modify DMI information (include Manufacture, Product Name, Part Number, Serial Number, UUID, OEM String, BT MAC).
3-60 AT300/AT305/AT500
(b) Use keyboard to input DMI information, when finished, press enter.
AT300/AT305/AT500 3-61
(c)
3-62 AT300/AT305/AT500
3.5 Appendix
NO# Equipment Description Quantity Remarks
mini-USB cable
SD Card
router
AT300/AT305/AT500 3-63
Chapter 4
Contents
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 4.19 4.20 4.21 4.22 4.23 4.24
Remove the SD Dummy Card ...................................................................................... 3 Remove the Rear Case Module..................................................................................... 4 Remove the Camera Lens ............................................................................................. 6 Remove the Power Button and Volume Button ............................................................ 7 Remove the Speaker ..................................................................................................... 8 Remove the Touch Panel Board ................................................................................... 9 Remove the Docking Board ........................................................................................ 12 Remove 2M Camera Module ...................................................................................... 14 Remove the Battery Module ....................................................................................... 15 Remove the Sidekey Board Module ........................................................................... 17 Remove the Card Reader Board ................................................................................. 20 Remove the Mainboard ............................................................................................... 22 Replace the Mainboard ............................................................................................... 25 Replace the Card Reader Board .................................................................................. 28 Replace the Sidekey Board Module ............................................................................ 30 Replace the Battery Module........................................................................................ 33 Replace 2M Camera Module ...................................................................................... 35 Replace the Docking Board ........................................................................................ 36 Replace the Touch Panel Board .................................................................................. 38 Replace the Speaker .................................................................................................... 41 Replace the Power Button and Volume Button .......................................................... 42 Replace the Camera Lens............................................................................................ 43 Replace the Rear Case Module ................................................................................... 44 Replace the SD Dummy Card ..................................................................................... 46
AT300/AT305/AT500
AT300/AT305/AT500 consists of various modules. This chapter describes the procedures for the complete tablet disassembly and assembly. In addition, in between procedures, the detailed disassembly and assembly procedure of individual modules will be provided for your service needs.
SD Dummy Card Rear Case Module Camera Lens Power Button and Volume Button Speaker Touch Panel Board Docking Board 2M Camera Module Battery Module Sidekey Board Module Card Reader Board Mainboard
AT300/AT305/AT500
4.1
1. Shut down the operating system and separate the machine from the docking. 2. Turn over the tablet PC. Catch the gap on the SD dummy card and remove it from the tablet PC .
AT300/AT305/AT500
4.2
1. Slide a stick carefully around the LCD module to open the latches between the rear case and LCD module. (Be careful not to touch the power button)
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Disconnect the speaker cable connecting with the docking board and remove the rear case module.
AT300/AT305/AT500
4.3
1. Push the camera lens out from the back of rear case module. (Be careful not to hurt the camera lens)
AT300/AT305/AT500
4.4
1. Push the power button out and remove it from the rear case module.
2. Push the volume button out and remove it from the rear case module.
AT300/AT305/AT500
4.5
AT300/AT305/AT500
4.6
1. Disconnect the touch panel cable connecting with the touch panel board.
2. Remove 2 short captons pasted on the connectors on the touch panel board and mainboard.
3. Disconnect the touch panel board cable connecting with the touch panel board and mainboard and remove it.
AT300/AT305/AT500
10
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 6. Remove the touch panel cushion and 2 touch panel PCB gasket on the touch panel board.
AT300/AT305/AT500
11
4.7
1.
3. Remove 2 screws(M1.4*4.7) and 2 screws(M1.4*2.7) on the docking board and take the docking board away.
12
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Remove 1 long capton on the connector on the back of the docking board.
5. Disconnect the docking board cable connecting with the docking board and remove it.
AT300/AT305/AT500
13
4.8
2. Disconnect 2M camera cable connecting with the mainboard and remove 2M camera module.
14
AT300/AT305/AT500
4.9
AT300/AT305/AT500
15
3. Slide a stick carefully around the battery to separate battery from the battery frame. (Be careful not to hurt the battery and the battery frame)
16
AT300/AT305/AT500
2. Disconnect the sidekey board cable connecting with the sidekey board and mainboard.
AT300/AT305/AT500
17
4 Disassembly and Assembly Procedures 4. Take the sidekey board module away (It includes vibrator, 5M camera and sidekey board).
5. Disconnect 5M camera cable connecting with the sidekey board and remove 5M camera.
18
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 7. Remove 2 sidekey PCB back gasket on the sidekey board.
AT300/AT305/AT500
19
2. Disconnect card reader board cable connecting with the card reader board and mainboard.
20
AT300/AT305/AT500
5. Remove 2 SD PCB gasket and 1 PCB SC gasket on the card reader board.
AT300/AT305/AT500
21
2. Disconnect LCM cable connecting with the mainboard and remove 1 short captons on LCM cable.
22
AT300/AT305/AT500
AT300/AT305/AT500
23
4 Disassembly and Assembly Procedures 5. Remove 7 PCB SC gasket and 1 sidekey PCB back gasket.
24
AT300/AT305/AT500
AT300/AT305/AT500
25
4 Disassembly and Assembly Procedures 3. Place the mainboard on the LCD module.
26
AT300/AT305/AT500
5. Connect LCM cable with the mainboard and paste 1 short captons on LCM cable.
AT300/AT305/AT500
27
28
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 3. Secure 2 screws(M1.4*2.7) on the card reader board.
4. Connect the card reader board cable with the card reader board and mainboard.
5. Paste 2 short captons on the connectors on the card reader board and mainboard.
AT300/AT305/AT500
29
30
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Place the sidekey board module on the LCD module (It includes vibrator, 5M camera and sidekey board).
6. Connect the sidekey board cable with the sidekey board and mainboard.
AT300/AT305/AT500
31
4 Disassembly and Assembly Procedures 7. Paste 3 short captons on the sidekey board cable and connectors on the side key board and mainboard.
32
AT300/AT305/AT500
2. Press the four sides of the battery module to fix it on the battery frame.
AT300/AT305/AT500
33
4 Disassembly and Assembly Procedures 4. Paste 1 long capton and secure 6 screws(M1.4*2.7) on the battery frame.
34
AT300/AT305/AT500
AT300/AT305/AT500
35
3. Paste 1 long capton on the connector on the back of the docking board.
36
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Place the docking board on the LCD module and secure 2 screws(M1.4*4.7) and 2 screws(M1.4*2.7) on the docking board.
AT300/AT305/AT500
37
38
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Connect the touch panel board cable with the touch panel board and mainboard.
5. Paste 2 short captons on the connectors on the touch panel board and mainboard.
AT300/AT305/AT500
39
4 Disassembly and Assembly Procedures 6. Connect the touch panel cable with the touch panel board.
40
AT300/AT305/AT500
2. Fix the speaker cable on the rear case module according to the picture below.
AT300/AT305/AT500
41
42
AT300/AT305/AT500
AT300/AT305/AT500
43
2. Fix the speaker cable in the LCD module according to the picture below.
44
AT300/AT305/AT500
4 Disassembly and Assembly Procedures 4. Lift the LCD module and turn it over. Then place the LCD module in the rear case module.
5. Press the four sides of the LCD module to lock the latches between the LCD module and rear case module.
AT300/AT305/AT500
45
46
AT300/AT305/AT500