Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Content Three phase 220V Input / Three phase 440V Input / Single phase 220V Input 0.75 01L 01H S1L 1 3.6 2.1 3.6 1.5 02L 02H S2L 2 6.8 3.7 6.8 2.2 03L 03H S3L 3 9.6 5.3 9.6 3.7 05L 05H -5 16.4 9.2 -5.5 07L 07H -71/2 22 11.8 -7.5 10L 10H -10 28 16 -11 -15H -15 -22 -EI-8001 series
3 220V Input 3 440V Input 1 220V Input Capacity (HP) Rated output current (A) 3220V Input 3440V Input 1200V Input
Output Characteristics
Power Supply
Rated input voltage and frequency Allowable fluctuation Control method Rated output voltage
Three phase 200~230V-50/60Hz / Three phase 380~460V-50/60Hz / Single phase 200~230V-50/60Hz Voltage 10% / Frequency 5% Sine Wave PWM Output voltage is settable between 0% and 120% with the output voltage adjustment function. Provided the rated voltage is 100%, output over the input voltage is disabled. 0.5 to 320 Hz. Set to 0.5 to 60Hz by default. Maximum frequency is adjustable between 30 and 320Hz. Analogue setting 0.5% the maximum output frequency or less (at 25C 10C) Factory preset at opened loop vector control suitable for most constant torque application. Adjustable for special applications. Factory preset, adjustable for high resistance torque, high inertia or low cycle operation machines. Automatic. The function can be prohibited or adjusted for frequency compensation. 150% -60 sec. 30% of the nominal motor torque without brake resistor (typical value) up to 150% with brake resistor as an option. 150%-60 sec. Built-in potentiometer on the front panel, external potentiometer on main terminal (1K to 10K variable resistor connectable). 0 to 10VDC (Input impendence: V1A=30.55K VIB=30K), 4 to 20mA (input impedance: 400), and optional Characteristics (gain, bias) can be preset by 2-point setting. Adjustable proportional gain.
Control Characteristics
Frequency setting resolution 0.1Hz Analogue input = max 100Hz and 0.1Hz. Frequency accuracy Voltage Frequency Characteristics Frequency feedback gain
Slip compensation
Major Control Function
Maximum transient current Braking torque Overload current rating Frequency setting signal
PI control
Operation Specification
Acceleration and deceleration Independent and adjustable, ramp time from 0.1 to 3600 seconds (0.1S time interval) adjusting ramp time automatically when over torque. Be able to eliminate ramp time auto-adjustment during decelerating. Recalculation Can be restarted after the main components checked during the protective function enable. Braking to stop DC injection type: Input DC current from a logic input terminal. Input DC current automatically between 0 to 25 seconds. Or input continuously Automatically input during the speed down to 0.5Hz. Forward & reverse input signals, preset speed select input signal, reset input signals, etc. Low-speed detection output signal, speed-reached output signal, etc. IC contact output (250VAC-2A, 30VDC-2A resistive load, 30VDC-1.5A inductive load).
Input terminal function (selection) Output terminal function (selection) Fault signal
Electrical isolation between power and control circuits (inputs, outputs, supplies) Short circuit protection: A. Internal supplies available. B. Between output phases. Thermal protection from excessive over heating and over currents. Under and over voltage supply. Over voltage during braking. Motor protection Protection integrated in the inverter by calculating (I x t) Service environment Indoor, Altitude must less than 1000 meters. Must not be exposed to direct sunlight, corrosive or explosive gas or vapor. Vibration: 5.m/s (0.6G) or less (at 10 to 50Hz). Ambient temperature & relative 10-40C (50C without upper seal) (93% no condensation). humidity Protective method IP20 Cooling Forced air-cooling.
Environment Protective function
Power Input
Forward Run/Stop Reverse Run/Stop Multi-Step Speed Setting1 Multi-Step Speed Setting2 Reset
(Third type grounding) Inverter abnormal output AC250V under 1A DC30V under 1A
Frequency Input
250VAC-1A
Internal power supply for outside 10V/10mA Maximum protected. Potentiometer use (1-1K). Voltage frequency command. Analogue input 0 -+10V, 30K Voltage frequency ref Analogue input 0 -+10V, 30K Compose with AI1. Current frequency ref Analogue input 0-20mA (factory preset) or 4-20mA (400). AI2, AIC are programmable but cannot be used simultaneously. Common point of digital input, Analogue input and digital output. Run forward command Digital signal input, 3.5K. (un-programmable) Input voltage+24V (30V max). When <5V,Logic 0. Run forward command When >11V,Logic 1. (programmable) LI2, LI3 and LI4 are programmable. Run multi-speed command (programmable) Error reset (un-programmable) Digital input, 3.5K. Input voltage+24V (reset). Power supply for external digital +24V/100mA max with protection. input use. Phototransistor contact point. LO+ Open collector output Transistor on when operated 24V max 50mA LOfrequency reaches the preset point.
W 114 191
W1 102 176
H 150 200
H1 137 186
D 116 178
D1 8 8
10L 10H-15H
220V 440V
Three-phase
10HP 10HP-15HP
228
204
298
286
206