Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
M.S.KENNEDY CORP.
4225
(315) 701-6751
FEATURES: Low RDS(ON) 0.013 Typical Low Cost Complete H-Bridge 20 Amp Capability, 75 Volt Maximum Rating Self-contained Smart Lowside/Highside Drive Circuitry Internal 45KHz PWM Generation, Shoot-through Protection Isolated Case Allows Direct Heatsinking Logic Level Disable Input Logic Level High Side Enable Input for Special Modulation or Function DESCRIPTION:
The MSK 4225 is a complete H-Bridge circuit to be used for DC brushed motor control or Class D switchmode amplification. All of the drive/control circuitry for the lowside and highside switches are internal to the circuit. The 45KHz PWM circuitry is internal as well, leaving the user to only provide an analog signal for the motor speed/direction, or audio signal for switchmode audio amplification. The MSK 4225 is constructed in a space efficient plastic power package that can be directly bolted to a heatsink.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
1 2 3 4 5 6 7 8 9 10
1
PIN-OUT INFORMATION
NC VCC HEN DIS NC INPUT NC GND GND NC 20 19 18 17 16 15 14 13 12 11 RSENSE A RSENSE A OUTPUT A OUTPUT A V+ V+ OUTPUT B OUTPUT B RSENSE B RSENSE B
Rev. A 7/04
TST Storage Temperature Range TLD Lead Temperature Range (10 Seconds) TC Case Operating Temperature MSK4225 TJ Junction Temperature
ELECTRICAL SPECIFICATIONS
Tc= +25C Unless Otherwise Specified
MSK 4225 Parameter OUTPUT CHARACTERISTICS RDS (ON) 1 4 VDS(ON) Voltage Instantaneous Forward Voltage Reverse Recovery Time Leakage Current PWM Frequency Vcc SUPPLY CHARACTERISTICS Analog Input=6VDC 9 1 Output A,B=50% Duty Cycle Output A=100% Duty Cycle High Output B=100% Duty Cycle High 1 Input Voltage LO Disable Input Input Voltage HI Input Current (DISABLE=0V) Input Voltage LO HEN Input Input Voltage HI Input Current (HEN=0V) SWITCHING CHARACTERISTICS Rise Time Fall Time Dead Time 1 RL=100 50 170 100 nS nS nS 2.7 2.7 0.8 135 0.8 270 V V uA V V uA 6 4 8 V V V 43 12 50 16 mA V 1 Each MOSFET ID=20A Each MOSFET ID=20A 3 3 40 0.45 1.0 1.0 45 0.013 0.52 1.3 280 25 50 V V nS uA KHz Test Conditions 2 Min. Typ. Max. Units
Each MOSFET IS=20A Intrinsic Diode Intrinsic Diode Each MOSFET V+=70V
INPUT SIGNAL CHARACTERISTICS Analog Input Voltage Analog Input Voltage Analog Input Voltage LOGIC CONTROL INPUTS
NOTES:
1 2 3 4 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Vcc=+12V, V+=28V, RSENSE A,B=Ground, DIS=0V, HEN=N/C unless otherwise specified. Measured using a 300S pulse with a 2% Duty Cycle. On Resistance is specified for the Internal MOSFET for Thermal Calculations. It does not include the package pin resistance.
Rev. A 7/04
This is a diagram of a typical application of the MSK4225. The design Vcc voltage is +12 volts and should have a good low ESR bypass capacitor such as a tantalum electrolytic. The analog input can be an analog speed control voltage from a potentiometer, other analog circuitry or by microprocessor and a D/A converter. This analog input gets pulled by the current control circuitry in the proper direction to reduce the current flow in the bridge if it gets too high. The gain of the current control amplifier will have to be set to obtain the proper amount of current limiting required by the system.
IN
Current sensing is done in this case by a 0.1 ohm sense resistor to sense current from both legs of the bridge separately. It is important to make the high current traces as big as possible to keep inductance down. The storage capacitor connected to the V+ and the module should be large enough to provide the high energy pulse without the voltage sagging too far. A low ESR ceramic capacitor or large polypropylene capacitor will be required. Mount the capacitor as close to the module as possible. The connection between GND and the V+ return should not be carrying any motor current. The sense resistor signal is common mode filtered as necessary to feed the limiting circuitry for the microprocessor. This application will allow full four quadrant torque control for a closed loop servo system. A snubber network is usually required, due to the inductance in the power loop. It is important to design the snubber network to suppress any positive spikes above 70V and negative spikes below -2V with respect to ground. *There are certain inductive load situations that can possibly cause a momentary shoot-through or cross-conduction condition in the MSK4225. This shoot-through is approximately 100nSec long and can be several amps, depending on the layout and impedence of the bypassing circuit. Most bypassing and current sensing filtering will usually eliminate the effects. However, in the case where it is still present, or the sense resistor trace lengths are long, reversebiased ultra-fast recovery diodes or power schottky diodes from RSENSE A and RSENSE B to power ground will minimize or eliminate the situation. 3 Rev. A 7/04
Rev. A 7/04
MECHANICAL SPECIFICATIONS
ESD Triangle Indicates Pin 1. NOTE: ALL DIMENSIONS ARE 0.010 UNLESS OTHERWISE LABELED.
ORDERING INFORMATION
Part Number MSK4225S MSK4225D MSK4225U MSK4225G Screening Level Industrial Industrial Industrial Industrial Lead Configuration Straight Down Up Gull Wing
Rev. A 7/04