Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
COP 2100/2500-Series
continuous production
Robust dimensions
COP 2160 and COP 2560 are among the most powerful rock drills on the market. The main differences from the earlier COP 2150/2550 series are a 10 mm bigger adapter, increased bearing surface, larger driver and an impact piston with a greater diameter at the striking end. The reason for the changes is to give even better impact tolerance for really heavy production work. But theres another important point: COP 2560 can be used not only with the T51 drill steel but also with the ThunderRod T60 for hole diameters of 102 mm and above. This drill steel has a 40 percent larger cross sectional area than the T51 and is therefore considerably more rigid. The resulting reduced hole deviation allows less dense hole planning and gives rise to significant savings in drilling time. Both models can be delivered with inbuilt extractors, identified by the suffix EX. As well as the above there is the COP 2150/2550 CR series, which consists of COPROD versions with separately transmitted impact energy and rotational torque for straighter holes in all types of rock conditions.
Rock drills without the double damping system cannot carry out satisfactory retightening of the extension rods. This means increased wear, which generates heat. The problem can therefore easily be detected with an ordinary thermometer.
Driver
Damping piston
Damping chamber
ce
Smart and reliable construction
The COP 2160/2160EX and COP 2560/2560EX are designed and con structed for maximum production with minimum maintenance: In a matter of minutes you can select the one of two (COP 2560/2560EX) or three (COP 2160/2160EX) stroke positions that provides the best piston frequency and penetration for the rock in question. The exceptionally strong rotation motor develops a drill steel torque of 1810 Nm, which minimizes the risk of jamming. The rock drills can also be supplied with a powerful hydraulic extractor to save time and drill steel. The flushing chamber is sealed very effectively against the stainless-steel flushing head and withstands air pressures of up to 12 bars. There is thus no problem keeping the bottom of the hole clean. Hydraulic-oil lubrication of the gear mechanism now replaces manual lubri cation. As well as reducing maintenance, this also improves cooling, which enables higher power utilization and helps to decrease wear under prolonged loading. Separate lubrication of the shank adapter and front bushing (fig 1) ensures adequate lubrication/cooling during heavy use and prevents contaminants from penetrating the drill at the front. Pressurized mating surfaces (with lubricating air, fig 2) prevent the ingress of dirt and damp into the drill. This facility can be disconnected if you so wish.
Fig.1. Separate compressed-air or hydraulic-oil lubrication of specially designed parts increases service life and operational availability.
3-stage protection
The COP 2160/2160EX and COP 2560/2560EX have three easily replac eable diaphragm accumulators. The inlet accumulator smoothes out pressure variations from the percussion mechanism to ensure continuous high efficiency. The damping accumulator is connected to the damping chamber and effectively smoothes out the pressure variations caused by the reflex shock wave. The return accumulator smoothes out pressure variations in the return oil and halts any harmful hose vibrations. Together the three accumulators contribute to the smooth running of the equipment, thus protecting the rock drill, the feed, the boom and the rig's hydraulic system. The resultant high operational availability leads to lower maintenance costs and higher production.
Fig 2. Mating surfaces and side rods are pressurized with lubricating air to prevent impurities from penetrating the drill and causing corrosion.
Fig 3. COP 2160EX and 2560EX. The hydraulic extractor is incorporated in front of the flushing head.
Penetration rate
m/min COP 2560 2.0 1.5 1.0 0.5 COP 2160 Soft rock
CIA A AB
TUBE ADAPTER
COUPLING
Damping chamber
Reversible variable-speed rotation motors with a total drill tube torque of 3960 Nm
Impact rod
Drill tube
Penetration rate
m/min COP 2550 2.0 1.5 1.0 0.5 Assumptions: Compressive strength, limestone = 160 MPa Compressive strength, granite = 200 MPa Hole length = 30 m Hard Drill bit = (semi) ballistic button bit rock 105 115 127 Hole diameter, mm COP 2150 Soft rock
COPROD section
For hole Length Drill tube Drill tube thread Impact rod COPROD 89 105 -127 mm 3.66/6.1 m 88.9 mm API 2 3/8-IF 45 mm
COPROD head
Length Thread COPROD 89 870 mm T-73
TED
Impact power, max. 21 kW Hydraulic pressure, max. 210 bar Impact rate, max. 36 Hz Lubricating air (at the rock drill), min. 2-3 bar Flushing air, max. 12 bar Weight, without adapter 187/249 kg Weight, with coupling and tube adapter Length, without adapter 1138/1336 mm Length, with coupling and tube adapter Width, without connectors 316 mm Height above cradle 223/257 mm Height above drill center 88/122 mm
Shank adapters
Male adapter thread type T45, length 770 mm for COP 2160, best.nr. 436-17301-05,00 Male adapter thread type T51, length 770 mm for COP 2160/2560, best.nr. 437-17301-05,00 Male adapter thread type T60, length 770 mm for COP 2560, best.nr. 457-17301-05,00 Male adapter thread type T45, length 770 mm for COP 2160EX, best.nr. 436-17201-05,00 Male adapter thread type T51, length 770 mm for COP 2160EX/2560EX, best.nr. 437-17201-05,00 Male adapter thread type T60, length 770 mm for COP 2560EX, best.nr. 457-17201-05,00
Rotation motor(s)
Rock drill type COP 2160/2560 and COP 2160EX/2560EX COP 2150CR/2550CR and COP 2150CRL/2550CRL Rotation motor type OMS 315 2 x OMS 315 Drill steel speed rpm 0-110 rpm 0-100 rpm Drill steel torque max. 1810 Nm 3960 Nm Output max. 15 kW 15 kW Working presure max. 200 bar 200 bar
Printed in Sweden
Rock drill
Thread type
Extension rod
Guide tube
(On special request only)
COP 2160, COP 2160EX T45 COP 2160/2560, COP 2160EX/2560EX T51 COP 2160/2560, COP 2160EX/2560EX T51 COP 2160/2560, COP 2160EX/2560EX T51 COP 2560, COP 2560EX T60 COP 2560, COP 2560EX T60 COP 2150CR/2550CR, COP 2150CRL/2550CRL
SPEEDROD) SPEEDROD SPEEDROD TDS 76 SPEEDROD TDS 87 THUNDERROD THUNDERROD TDS 87 COPROD 89
9851 2458 01
The manufacturer reserves the right to make modifications without prior notice. 2006.06 CIA A AB