Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Features:
z z z Compliant with specifications for IEEE802.3Z Multi-source package with Duplex LC Connector Eye Safety Designed to meet Laser Class1 Compliant with IEC60825-1 z z z z Up to 155Mb/s data links Single +3.3V Power Supply Hot-Pluggable Complies with Bellcore TA-NWT-000983
Applications:
z z z SONET OC-3/SDH STM-1 Switch to Switch interface Fast Ethernet
Standard:
z Compatible with SFP MSA
Description:
OFSS-1303-20 SFP transceiver is high performance, cost effective module. It is designed for Fast Ethernet and SONET OC-3/SDH STM-1 applications. The transceiver consists of two sections: The transmitter section incorporates a 1310nm FP laser. And the receiver section consists of a PIN photodiode integrated with a trans-impedance preamplifier (TIA). All modules satisfy class I laser safety requirements.
PRODUCT SELECTION
Page 1
I. Pin Descriptions
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VeeT TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VeeR VeeR VeeR RDRD+ VeeR VccR VccT VeeT TD+ TDVeeT Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled AC Coupled 1 Receiver Non-inverted DATA out. Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) 1 1 4 1 1 1 2 3 3 3 Ref. 1
Notes:
1. 2. 3. Circuit ground is internally isolated from chassis ground. Laser output disabled on TX Disable >2.0V or open, enabled on TX Disable<0.8V. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. LOS is LVTTL output. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Page 2
Notes:
1. 2. 3. 4. 5. 6. Non condensing. AC coupled. Into 100 ohm differential termination. 20 80 % LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ.
Notes:
1. 2. 3. 4. Class 1 Laser Safety. Unfiltered, 20-80%. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253 With worst-case extinction ratio.
Page 3
V. General Specifications
Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125m SMF @ OC-3 Symbol BR BER LMAX5 20 Min 125 Typ Max 155 10
-12
Units Mb/sec km
Ref. 1 2 3
Notes:
1. 2. 3. 4. Compliant with SONET and SDH at the following rates: OC-3 IR-1/STM S-1.1 and OC-3 SR/STM I-1 Tested with a PRBS 2 -1 data pattern. Dispersion limited per FC-PI-2 Rev. 10 Attenuation of 0.55 dB/km is used for the link length calculations. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.
23
OFS-1303-20
Page 4
Page 5
Page 6