Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CONTENTS
SAFETY NOTICE ................................................................................................................................... 4 GENERAL DESCRIPTION .................................................................................................................... 6 TECHNICAL SPECIFICATION ............................................................................................................. 7 GENERAL SPECIFICATION ................................................................................................................. 8 SAFETY CAUTIONS FOR PRODUCTS ............................................................................................... 9 ADJUSTMENT MODE ......................................................................................................................... 10 CHASSIS BLOCK DIAGRAM ............................................................................................................. 15 FAULT FINDING TREES..................................................................................................................... 16 IC BLOCK DIAGRAM ......................................................................................................................... 23 MAIN CHIP INSTRUCTION................................................................................................................ 24 FACTORY MENU ................................................................................................................................ 45 EXPLODED VIEW AND PART NAME .............................................................................................. 48 BOM LIST ............................................................................................................................................. 49 CIRCUIT DIAGRAM ............................................................................................................................ 58
SAFETY NOTICE
WARNING: BEFORE EXAMINING AND SERVICING THIS CHASSIS, READ CAREFULLY THE FOLLOWING SAFETY INSTRUCTIONS.
X-RAY RADIATION PRECAUTION
1. The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X-RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this service manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, take necessary corrective action. Carefully follow the instructions for +B1 volt power supply adjustment, and high voltage check to maintain the high voltage within the specified limits. 2. The EHT must be checked every time the receiver is serviced to ensure that the CRT does not emit X-ray radiation as result of excessive EHT voltage. The nominal EHT for this receiver is 22KV at zero beam current (minimum brightness) operating at AC 220V. The maximum EHT voltage permissible in any operating circumstances must not exceed 25KV. When checking the EHT, use the High Voltage Check procedure in this manual using an accurate EHT voltmeter. 3. 4. The only source of X-RAY radiation in this receiver is the CRT. To prevent X-ray radiation, you should use the same type of CRT when replacing it. Some components used in this receiver have safety-related characteristics preventing the CRT from emitting X-ray radiation. For continued safety, replacement component should only be made after referring the Product Safety notice below.
SAFETY PRECAUTION
1. The high voltage in the TV reaches to 22KV when the TV is in operation. Be more careful during opening the back cover. a. b. c. d. 2. 3. The high voltage existing in the TV is very dangerous. Refer servicing to qualified personnel only. Before removing the high voltage cap. Discharge the anode of the CRT and the chassis in case of electric shock. Wear a pair of goggles when handling the CRT to avoid broken pieces damaging your eyes. Do not hold the CRT neck in case of causing damage to the CRT. When the power cord needs replacing, use the same one as that provided by AKIRA factory. Voltage exists between the hot and cold ground when TV is in operation. Install a separation transformer during repairing or connecting to any tester for the sake of safety. The power of the separation transformer should be beyond rated overall power.
Model No: 21WHS3-Bn Version 1.0
5 4. 5. When replacing a burnout fuse, use the one with the same specifications as the original. When replacing old wire, wind new one round the shaft to weld. When replacing components with safety in performance, use the same type as that specified by AKIRA and install it in the former way. 6. 7. 8. 9. Never place wire near high-temperature or high-voltage components. An isolation transformer should be connected in the power line between the receiver and the AC line when a service is performed on the primary of the converter transformer of the set. Comply with all caution and safety-related notes provided on the cabinet back, inside the cabinet, on the chassis or the picture tube. When replacing a chassis in the cabinet, always be certain that all the protective devices are installed properly, such as, control knobs, adjustment covers or shields, barriers, isolation resistor-capacitor networks etc.. Before returning any television to the customer, the service technician must be sure that it is completely safe to operate without danger of electrical shock.
GENERAL DESCRIPTION
AKPH02 chassis series are applied in A14P01/A21P01 respectively which uses mainly Philips advanced UOC-ultimate chip TDA935X/6X/8X and I2C-bus controlled IC. With combination of microcontroller and small signal processor, the TDA935X/6X/8X series feature high-integration, high-performance-to-price ratio and high-reliability and advanced functions with fewer external components, which provide much convenience for manufacturing and technical service. Table 1 provides A14P01/A21P01 mainly ICs and functions.
THE SURVEY
Table 1, the main IC and functions
Function Description Microcontroller and small signal processor(UOC) EEPROM Sound power amplifier Vertical scan output stage circuit AV1/AV2 Switch AV1/AV2 Switch
SIGNAL PROCESS
The TV signal enters into tuner (A201) from cable or antenna. Pin 10 and pin 11 of N301 are combined to select the band. Pin 4 of N301 outputs PWM tuning signal. The 38.9MHz IF signal is coupled to V308 (pre-amplify) and then to SAWF (Z301). After processed in the SAWF, the 38.9MHz signal gets to pin 23 and pin 24 of OM8370. The IF circuit in OM8370 includes such unit as the AGC amplifying circuit, 38.9MHz oscillator, PLL video demodulator, video amplifier, IF identify circuit and AFT circuit. The demodulated signal (CVBS) comes from the pin 38 of OM8370, the sound signal comes from the pin 44. The internal CVBS signal needs norm identification then outputs from pin 38 of OM8370, via the trap circuit (composed of the V351, Z351, Z354, V352 and so on) feeds back to the pin 40 of OM8370. The RGB signal comes from pin51, Pin52, Pin53 of OM8370, and outputs to the CRT board. The internal sound signal comes from pin 44 of OM8370 and then input to pin 1 and pin 12 of HEF4052BP. The sound signals from RF and AV are selected in it. The selected signal is output from Pin 3 and pin13, then input AN7522N (sound amplifier) or output from AV terminals.
TECHNICAL SPECIFICATION
Test Item
AC Operating Range
Conditional
RF&AV signal input with sound loud speaker (volume maximum) & Picture set in Dynamic mode Philips or Mono-scope pattern signal with howling sound Contrast & Brightness set in Maximum, sound increase maximum Standby Mode Brightness & contrast set in Maximum
TD171
140Vac ~ 240Vac
90Watts 14 Watts Min: 26.2KVdc Average: 26.5KVdc Max: 27.8KVdc IABL 1.2mA V Heater = 6.2Vac VB+ = 112Vdc V = 6.3Vrms P = 5Watts X 2
EHT
Typical Design value Brightness &contrast Minimum Brightness &contrast Maximum TV operate normally Normal operating RF signal input broadcasting at 217.25MHz/BG/DK(1KHz) Volume is maximum
GENERAL SPECIFICATION
Power consumption Receive system Color system Vision intermediate frequency Inter-carrier frequency Chroma if frequency PAL Antenna type Channel receiving Tuning system AV IN/ OUT Component IN AV IN/ OUT specification 14 21 DK/BG/I PAL/ SECAM/ NTSC 38.9MHz 5.5 MHz(B/G) 6.5MHz(D/K) 34.47/ 35.32MHz DIN TYPE 75 Ohm VHF Low channel =48.25 to 147.25 MHz (VL) VHF high channel =154.25 to 463.25 MHz (VH) UHF channel (U) =471.25 to 863.25 MHz VS tuning 2 AV STEREO IN + 1 AV STEREO OUT 1 YUV-Component IN VIDEO IN ----1.0 0.2Vp-p 75 Ohm AUDIO IN ----0-2V (RMS) VIDEO OUT ----1.0 0.2Vp-p 75 Ohm AUDIO OUT ---- 0-2V (RMS) English, Russian, Turkish, French, Spanish, Vietnamese, Indonesian, Arabian, Persian > 8W (1KHz, 0.5V INPUT, 10% THD CB Power ON HS08 Pin AAx2 14 21 90 degree tube 5m Video/Audio (L/R) 2set input YUV input S-Video input Video/ Audio (L/R) 1 set output 70W 90W MAX MAX
OSD language Audio output power Safety authentication standard LED indicator Hand set type Hans set power supply Color picture tube Remote control distance External input/output
CIRCUIT ADJUSTMENTS
GENERAL INFORMATIONS
All adjustment are thoroughly checked and corrected when the receiver leaves the factory. Therefore the receiver should operate normally and produce proper color and B/W pictures upon installation. However, several minor adjustments may be required depending on the particular location in which the receiver is operated. This receiver is shipped completely in carton. Carefully draw out the receiver from the carton and remove all packing materials. Power cord into a convenient 220 volts 50 Hz AC two pin power outlet. Turn the receiver ON. Check and adjust all the customer controls such as BRIGHTNESS, CONTRAST and COLOUR Controls to obtain natural color or B/W picture.
AUTOMATIC DEGAUSSING
A degaussing coil is mounted around the picture tube so that external degaussing after moving the receiver is normally unnecessary, providing the receiver is properly degaussed upon installation. The degaussing coil operates for about 1 second after the power to the receiver is switched ON. If the set is moved or faced in a different direction, the power switch must be switched off at least 30 minutes in order that the automatic degaussing circuit operates properly. Should the chassis or parts of the cabinet become magnetized to cause poor color purity, use an external-degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube, the side and front of the receiver and slowly withdraw the coil to a distance of about 2m before disconnecting it from AC source. If color shading still persists, perform the COLOUR PURITY ADJUSTMENT and CONVERGENCE ADJUSTMENTS procedures.
10
ADJUSTMENT MODE
Item
Measuring Equipment Preparation Before Adj.
Adjustment procedure
1, Turn VR501 potentiometer to adjust B+ to specified voltage. 2, Check voltages for video out, vertical out, circuit work and audio power out as follow Voltage (volt) 14 inch 21 inch +B Video Out Vertical Out Circuit Work Audio Power Out 110 188 26 13 12 110 188 26 13 12 Tolerance 2V 5V 1V 1V 1V
3, TV signal receiving 1. Press MENU key, to select POS.MEMORY item. Press V+ or V- key, to select SEARCH or AUTOMEMORY item, press P+ key to start searching. 2. Press P+ or P- key to inspect the set if there is channel skipped, if so, searching again by SEARCH as above described.
11
Item
Measuring Equipment Preparation before Adj.
Inspection procedure 1, Input the TV signal which system is designated in technical specification 2, Switch TV system to the set by pressing SYS key on user remote controller according to the TV system in SG. The picture and sound must be normal. 3, Press TV/AV key, to select AV input. The picture and sound must be normal 4, AV output inspection. Load a 75 resistor to VIDEO output terminal,1Vp-p video output signal that is from TV signal should be observed on the oscilloscope. Load a 10K resistor to AUDIO output terminal, 0.7Vp-p audio output signal that is from TV should be observed on the oscilloscope.
Item
Measuring Equipment Preparation before Adj.
Focus adjustment
AKPH01 chassis SG Brightness, contrast and color should be set in standard
Adjustment procedure
1, Receive the cross-hatch pattern signal 2, Turn the focus adjusting VR watching the screen and adjust the vertical line of mark to make the most thin. Then the focus adj. VR is set as close low voltage side as possible. Stop the focus adj. VR at the point that focus is a bit worse at once, turn back to the left and then turn back to the right a little again.
12
To be fine H. line
part
MENU9 CRT cut-off and white balance and sub-brightness adjustment. Receive gray and white 2 steps signal. a) CRT cut off adjustment. 1. push [P+][P-] key to select SC, push [V+][V-] key then automatically vertical scan will be stopped. 2. adjust SCREEN control on Flyback transformer to get the darkest single horizontal line (red, green, or blue, sometimes shows more yellow, more purple or more white). 3. push [V+][V-] key again, vertical scan work repeat. b) white balance adjustment. a) select RD/BD menu. b) adjustment RD/BD to get color temperature as x=282, y=292. c) sub-brightness adjustment (use stair case signal) 1. select SB MENU.
adjust SB to get the darkest step being out off.
13
Item
Measuring SG and digital multi meter Equipment service remote controller Preparation Connect a digital multi meter to AGC point on the chassis before Adj. Adjustment procedure 1, Receive the color bar signal that is 87.5% modulation and 60dBu level 2, Press AGC-TOP on service remote controller to select AGC-TOP adjustment, press + or key to adjust the voltage of AGC-TOP to 6.20.05V that is read on the digital multi meter.
Item
Measuring Equipment Preparation before Adj.
Vertical height, linearity and Hor. position adjustment AKPH01 chassis SG service remote controllers Brightness, contrast and color should be set in standard
MENU8 Geometrical adjustment. Receive standard Crosshatch pattern Horizontal line signal for PAL system . a) Adjust VSLOPE value, to the horizontal line just appear from Shadow half bottom shadow. b) Adjust VSHIFT value, the center horizontal line correspond to CRT vertical center. c) Adjust Vamp value, to get 90% of vertical picture contents would be displayed on CRT. d) Adjust HSHIFT value, to get the picture horizontal center correspond to CRT horizontal center. e) Receive standard Crosshatch pattern signal for NTSC system, and again adjust.
14
Item
Measuring Equipment Preparation before Adj.
Adjustment procedure 1, Press 5 key on service remote controller to set the set into design mode adjustment 2, Press or key to select OSD VPOS item, press or key to adjust the OSD to the center position on the screen or press OSD HPOS on service remote controller and press + or key to adjust the OSD position. 3, Press M key again to quit design mode adjustment.
Item
Measuring Equipment Preparation Before Adj.
Inspection procedure 1, Receive the Philips pattern signal 2, Press PIC key on user remote controller to call the menu as adjusting picture quality. Adjust color, brightness, contrast, sharpness and tint (in NTSC) respectively and all adjustment should be right 3, Press V+ key to increase the sound volume, no distortion heard at maximum level, press V- key to decrease the sound volume, no sound heard at minimum level 4, Press POWER key to switch the set into standby status, at mean time the manufactory adjustment mode is cancelled 5, Press POWER key again, the set should work in normal receiving mode 6, Press (mute), QV (display), PP and TIMER key respectively, the relevant function should be normal
15
10
SP161 85W
15
13 9 10 63 42 62 44 47 46 48 43
V351
38 7 40 53
4
2
SP162 L 85W
11
5 14 11 15
TV AUDIO OUT
52 51
CRT
21
IF PRE-AMP V308
SAWF Z301
23 24 11 10
22
33
6
64 2
HORIZONTAL DRIVE V450 HORIZONTAL OUTPUT V451 SCREEN EHT FOCUS HEAT
3 T450
KEY BOARD
SCL
6
SDA
5
AC150-260V 50/60Hz
Bridge rectification
VD503-VD506
POWER SUPPLY CIRCUIT V553 V1511 T V1512 Filter C507 +300V 501 N504
200V
FBT(T402) BSC25
+15V
-15V
16
0V 300V
130V
115V 115V N301 pin39voltage 8V N301 pin33 voltage 2V V450 pin C voltage Check R539,V1553,VD1561 N504,V1511,V1512,R556
Voltage of C507 0V NO
YES
Check V1513,V1512,F501,XR502,VD503 300V Test voltage of V1513 base 0.6V Check T501,VD1517, C1515,C1517,V451, VD522-VD529 C455,C456,T451 C467 0V Check if it get right When cut off V504 YES Test the voltage of N301 pin1 4.5-5.5V CPU has sent the Power-off signal
Check T501
1V
Check VD522,C528B
24V
0V
115V Recover R458, unplug XS403 for a While,then test the voltage of C528B No variation Check V1513 0V Check V451,T451,T450, Deflection coil
Check R452,V450 Others Check V451 pin C voltage 115V Check T451,V451,R458
Check T451
17
B Two-None (no picture, no sound) The failure shows that the set does not display the picture but it has noise wave or blue background or OSD on the screen. This means that the circuits of power supply, horizontal scanning, vertical scanning and video amplification are normal and they are not considered in the repairing. The failures are mainly in the small signal processing circuits. Before checking these circuits, a kind of practical test method is introduced. It is called Signal-input way . The detail is described as follow: We can use the resistance function of an analog multimeter, connect the red pole (negative in ohm scope) on the circuit board ground, then touch softly the test point with another pole (black pole) in ohm scope meanwhile observe the reactivity on the output device. Note : In the TV test, we mainly observe the noise wave on the CRT and listen to the noise voice liking as Ka..Ka from the loudspeakers. 1. No picture No picture
NO
Check R703,N703,C703A
33V
Check the voltage on the C705 0-33V Check R707, C707, A101
No variation
The voltage between VL and BH vary from 0V to 5V or not when auto searching Check ,V701,N301, R701, R701A ,R704,R705,C701,C705,C706 YES
18
2V
Exam the voltage of AGC on A101 without antenna Check R317, R318, R316,C307,A101,N301
3.8V
0V
0V
Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 23 and pin 24 of N301 NO YES Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 38 of N301 NO Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 17 of N301 NO Observe if snow-noise-wave disturbance on the CRT via using signal-input way by touching pin 40 of N301 NO YES Check if voltage on pin 31 of N301 is 1.7V 2V Check C323,A101,N301 Test if there is the sync signal on the pin 39 of N301 NO Check C361,C362,L361,N301 YES YES
Check R331,C336,C337
Check V351,V352,L351,Z351,C364
Observe if these is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 51,52,53 of N301 NO Check R381,R382,R383,V912,V922,V932,N301
19
5. No sound
In this kind of failure, first of all we should observe if there is the picture on the CRT. It proves the small signal circuit to work correctly with the picture on the CRT and we only check the sound signal processing and sound amplification circuit. The repairing method(B1) may be referred without picture. The detail checking and repairing steps are as follow. Note: Before repairing, assure that the volume is on and the state of set is in TV . YES
Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 7 of N301 NO YES Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 44 of N301
NO
Check C367,R369,V395,N301
Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 3 of N121 NO Check 8V-power supply YES
8V
Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 13 of N121 NO
Check R153,C153,R154,C154,N121
Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 6,8of N161 YES Check C157,C153, N101
5V
NO The voltage on pin 1 of N701 12.5V 8V Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 2,10 of N701 NO Check SP161, SP162, N161 Check R126,N505, N121 The voltage on pin 9,10of N121
Check VD521,R165,C522,T501,N161
20
Abnormal The waveform on the pin 21,22 of N301 Check C401,C402,R401,R402,N301 Normal The voltage on pin 2 of N401 Abnormal 24V Measuring the waveform on pin 1 of N401 Check VD470, R470,VD401,N401 0V
Normal
Normal
Check N402
Abnormal
21
Vertical line
YES The horizontal yoke is opened or not NO Whether XS403 is opened Repair CRT
YES
Check if there is bad solder between XS403, and the main board
NO
22
3.3V
Check the voltage on the positive pole of C548 =3.3V Check alternant voltage on secondary coil of N505, YES Check T501, VD522,R565 Check the voltage on the positive pole of VD522 3V Check VD522, T501 =14V Check R565,R546,N505 NO Check R561,VD564
No OSD Check the wave on the pin 7 of FBT NO Check FBT T451 Check C482, R485, VD483, R487, N301 YES
23
IC BLOCK DIAGRAM
Fig 1: UOC-TDA9381 Illustration
24
Pin 26 Pin 27 Pin 28 Pin 29 Pin 30 Pin 31 Pin 32 Pin 33 Pin 34 Pin 35
BAND 1 control output. BAND 2 SECAM PLL, connected with a capacitance (no use in this type). +8V power source supply Using a capacitor of 220n in series to GND. This pin decouples the internal digital supply voltage of the video process and minimizes the disturbance to the sensitive analogue parts. Phase-2 control loop, this pin requires a capacitor at 2.2nF in series to GND. Phase-1 control loop filter connected to pin 17 is suitable for various signal conditions like strong /weak and VCR signal. This is achieved by switching of the loop filter time constant by changing the Phase-1 output current. GND Bandgap decoupling, the bandgap circuit provides a very stable and temperature independent reference voltage. This reference voltage (4.0V) ensures optimal performance of the analogue video processor part of the OM8370 and is used in almost all functional circuit blocks. East-west pillow signal output. Vertical drive output. IF input. Reference current/ This pin requires a resistor to ground. The optimal reference current is 100mA which is determined by this resistor. The 100mA reference current should not be changed because the geometry processor is optimized for this current. Furthermore the output current of vertical drive and EW are proportional to this current. Vertical sawtooth. This pin requires a capacitor to ground of 100nF. AGC output. This output is used to control (reduce) the tuner gain for strong RF signals. Audio de-emphasis. Sound decoupling. This pin requires a capacitor connected to ground. The pin acts as a low pass filter needed for the DC feedback loop. GND Sound loop filter. AVL filter Horizontal drive signal output, needs a resistor in series to +8V. Sandcastle output /flyback input. External audio input, this pin should be grounded in this chassis.
25
Pin 36
Pin 37 Pin 38 Pin 39 Pin 40 Pin 42 Pin 43 Pin 44 Pin 45 Pin 46, Pin 47, Pin 48 Pin 49 Pin 50 Pin 51, Pin 52, Pin 53 Pin 54 Pin 55 Pin 56 Pin 57, Pin 58, Pin 59 Pin 60 Pin 61 Pin 62 Pin 63 Pin 64
EHT tracking /over voltage protection. If something is wrong, the anode high voltage rise the heater voltage will rise too. When the rising voltage arrive some limit, the V406 works, the voltage of pin 36 will exceed 3.9V. The OM8370 will stop working. PLL loop filter. CVBS output. Monitor or RF videos can be selected. +8V supply source CVBS input Y signal input C signal input Main audio output. This pin is connected to the TDA9859. RGB signal input blanking. RGB signal input. ABL. It means been current limiter input. R410 is the control resistor. Black current input from the CRT board. RGB drive signal output to the CRT board. +3.3V GND +3.3V 12MHz crystal Reset. NC in this chassis +3.3V NC This pin is connected to the HEF4094. Functions expending. IR signal input.
26
27
Notes: H = HIGH state (the more positive voltage) L = LOW state (the less positive voltage) X = state is immaterial
28
29
30
31
32
33
34
35
36
37
38
39
40
1 2 3 4 5 6 7
Inverting input Vcc Pump up out GND VER output Output stage Vcc Non inv. Put
41
42
43
44
45
FACTORY MENU
Main power +B setting
Receive standard color pattern RF signal. Set picture to Standard Mode. Adjust VR501, to get +B (VD542 -) voltage =110V.
M1
0~3
M2
ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF 0~2 ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF
M3
46
MI M4
Items SUBCON SUBCOL SUBSHP SUBTINT YDLY PAL YDLY NTSC YDLY SEC YDLY AV UOC VOL CATHODE SC BRI OSD VPOS OSD HPOS WIDE ZOOM NENU TITLE E2PROM ADRESS E2PROM VALUE E2PROM WRITE SHIPMODE SEARCH SPEED AGC-TOP AGC-SPEED FREQUENCY VSLOPE VSHIFT VAMP VSCOR HSHIFT BT CT SC RB GB RD GD BD SB
Variable 0~63 0~63 0~63 0~15 0~15 0~15 0~15 0~15 ON/OFF 0~15 0~63 0~63 0~59 0~63 0~63 0~6 0~33 0~95
Preset 63 63 63 15 12 12 12 12 Off 15 10 53 15 15 59 3
M5
M6 M7
M8
0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63
M9
47
2. method of LOGO input: 3) when E2PROM ADRESS = 0, to adjust E2PROM VALUE may be changed horizontal position of LOGO. Its range is from 10 to 20. 4) when E2PROM ADRESS =1, to adjust E2PROM VALUE may be changed vertical position of LOGO. Its range is from 1 to 30. 5) when E2PROM ADRESS =2, to adjust E2PROM VALUE may be changed color of LOGO. Its range is from 0 to 7. VALUE 0 1 2 3 4 5 6 7 COLOR RED BLUE GREEN CYAN ORANGE PINK YELLOW WHITE 6) when E2PROM ADRESS =3, to adjust E2PROM VALUE may be changed size of LOGO. Its range is from 0 to 3. 7) when E2PROM ADRESS =4~33, to adjust E2PROM VALUE may be changed character of LOGO. Its range is from 0 to 95.
48
49
BOM LIST
Ref. No R411 R312 R871 R914 R924 R934 R398 R806 R368 R708 R911 R921 R931 R354 R355 R304 R801 R313 R301 R302 R363 R365 R366 R381 R382 R383 R401 R402 R452 R723 R724 R743 R815 R824 R861 R862 R815A R848 R852 R353 R311 R917 R927 R937 R913 R923 R933 R805 R916 R926 R936 R322 R308 Part No. RJB393F-NAAF D10B683J-T D10B4R7J-T D10B4R7J-T D10B330J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B151J-T D10B151J-T D10B151J-T D10B151J-T D10B151J-T D10B221J-T D10B221J-T D10B221J-T D10B301J-T D10B301J-T D10B301J-T D10B331J-T D10B331J-T D10B331J-T D10B331J-T D10B391J-T D10B471J-T Name Resistor metal Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Specification Rj13-1/6W-39K-F RT13-1/6W-10-J RT13-1/6W-10-J RT13-1/6W-22-J RT13-1/6W-22-J RT13-1/6W-22-J RT13-1/6W-33-J RT13-1/6W-33-J RT13-1/6W-47-J RT13-1/6W-47-J RT13-1/6W-47-J RT13-1/6W-47-J RT13-1/6W-47-J RT13-1/6W-56-J RT13-1/6W-56-J RT13-1/6W-68-J RT13-1/6W-75-J RT13-1/6W-82-J RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1505% RT13-1/6W-1505% RT13-1/6W-1505% RT13-1/6W-1805% RT13-1/6W-2205% RT13-1/6W-2205% RT13-1/6W-2205% RT13-1/6W-2205% RT13-1/6W-3005% RT13-1/6W-3005% RT13-1/6W-3005% RT13-1/6W-3305% RT13-1/6W-3305% RT13-1/6W-3305% RT13-1/6W-3305% RT13-1/6W-3905% RT13-1/6W-4705%
50
Ref. No R1517 R316 R482 R128 R129 R369 R460 R464 R481 R734 R802 R803 R816 R818 R825 R827 R305 R560 R397 R732 R430 R405 R1523 R351 R371 R451 R463 R701A R321 R702 R721 R722 R728 R735 R736 R737 R741 R742 R455 R462 R131 R133 R154 R158 R306 R733 R370 R540 R701 R1511 R153A R157A R126 R127
Part No. D10B471J-T D10B681J-T D10B681J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B122J-T D10B122J-T D10B152J-T D10B152J-T D10B182J-T D10B182J-T D10B182J-T D10B222J-T D10B222J-T D10B222J-T D10B222J-T D10B222J-T D10B272J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B332J-T D10B392J-T D10B392J-T D10B472J-T D10B472J-T D10B472J-T D10B472J-T D10B472J-T D10B472J-T D10B562J-T D10B562J-T D10B562J-T D10B562J-T D10B822J-T D10B822J-T D10B103J-T D10B103J-T
Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor
Specification RT13-1/6W-4705% RT13-1/6W-6805% RT13-1/6W-6805% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1.2K5% RT13-1/6W-1.2K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.8K5% RT13-1/6W-1.8K5% RT13-1/6W-1.8K5% RT13-1/6W-2.2K5% RT13-1/6W-2.2K5% RT13-1/6W-2.2K5% RT13-1/6W-2.2K5% RT13-1/6W-2.2K5% RT13-1/6W-2.7K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-4.7K5% RT13-1/6W-4.7K5% RT13-1/6W-4.7K5% RT13-1/6W-4.7K5% RT13-1/6W-4.7K5% RT13-1/6W-4.7K5% RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-8.2K5% RT13-1/6W-8.2K5% RT13-1/6W-10K5% RT13-1/6W-10K5%
51
Ref. No R163 R380 R395 R396 R434 R461 R548 R551 R704 R705 R706 R707 R709 R816A R818A R825A R827A R851A R852A R912 R922 R932 R331 R162 R384 R804 R1515 R1556 R484 R487 R171 R175 R317 R385 R172 R732A R745 R173 R483 R802A R803A R807 R318 R174 R465 R404 R468 R513 R561 R486 R161 R1526 R485 R1522
Part No. D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B153J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B333J-T D10B333J-T D10B333J-T D10B333J-T D10B473J-T D10B473J-T D10B473J-T D10B683J-T D10B104J-T D10B104J-T D10B104J-T D10B104J-T D10B154J-T D10B274J-T D10B564J-T D10C1R0J-T D10C2R7J-T D10C220J-T D10C270J-T D10C101J-T D10C222J-T D10C222J-T D10C103J-T D10C153J-T
Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor
Specification RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-15K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-27K5% RT13-1/6W-27K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-47K5% RT13-1/6W-47K5% RT13-1/6W-47K5% RT13-1/6W-68K5% RT13-1/6W-100K5% RT13-1/6W-100K5% RT13-1/6W-100K5% RT13-1/6W-100K5% RT13-1/6W-150K5% RT13-1/6W-270K5% RT13-1/6W-560K5% RT14-1/4W-15% RT14-1/4W-2.75% RT14-1/4W-225% RT14-1/4W-275% RT14-1/4W-1005% RT14-1/4W-2.2K5% RT14-1/4W-2.2K5% RT14-1/4W-10K5% RT14-1/4W-15K5%
52
Ref. No R539 R539A R1554 R942 R407 R453 R1555 R507 R1520 R406 R300A Ref. No R466 R941 R530 R454 R546 R467 R703 R915 R925 R935 R556 R519! R918 R928 R938 R555 ! R565 ! R566 ! R165 ! R470 ! R472 ! R480 ! R458 R502 ! R1524 R504 PS501 VR501 C761 C762 C701 C701A C911 C921 C931 C803 C805 C812 C814 C824 C826
Part No. D10C513J-T D10C513J-T D10C154J-T D10C334J-T D10D271J-T D10D102J-T D10D473J-T D10D124J-T D10D124J-T S10E1R2J-C S10E220J-C Part No. S10E102J-C S10F5R6J-C S10F560J-C S10E271J-C S10F271J-C S10F103J-C S10F103J-C S10F123J-C S10F123J-C S10F123J-C S10F223J-C
Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Metal oxide resistor Metal oxide resistor Name Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Glass-Glazed Fixed RES Glass-Glazed Fixed RES Glass-Glazed Fixed RES Glass-Glazed Fixed RES Fuse resistor Fuse resistor Fuse resistor Fuse resistor Fuse resistor Fuse resistor Fuse resistor Wire-wound resistor Wire-wound resistor Wire-wound resistor Wire-wound resistor Thermittor Potentiometer Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor
Specification RT14-1/4W-51K5% RT14-1/4W-51K5% RT14-1/4W-150K5% RT14-1/4W-330K5% RT15-1/2W-2705% RT15-1/2W-1K5% RT15-1/2W-47K5% RT15-1/2W-120K5% RT15-1/2W-120K5% RY16/RY21-1W-1.25% RY17/RY21-1W-225% Specification RY16/RY21-1W-1K5% RY17/RY21-2W-5.65% RY17/RY21-2W-565% RY17/RY21-2W-2705% RY17/RY21-2W-2705% RY17/RY21-2W-10K5% RY17/RY21-2W-10K5% RY17/RY21-2W-12K5% RY17/RY21-2W-12K5% RY17/RY21-2W-12K5% RY17/RY21-2W-22K5% RI40-1/2W-24M5% RI40-1/2W-1.5K5% RI40-1/2W-1.5K5% RI40-1/2W-1.5K5% RF10-1/2W-0.275% RF10-1/2W-0.275% RF10-1/2W-0.275% RF10-1/2W-0.475% RF10-1/2W-0.475% RF10-1/2W-0.475% RF10-2W-3.95% RXG6-5W-3.9-J RXG6-6W-1.8-J RX27-5W-27-K RX27-5W-68-K PTC-180HM WI06-2AA2K CC1-06A-CH-50/63V-33pF-J CC1-06A-CH-50/63V-33pF-J CC1-06A-CH-50/63V-120pF-J CC1-06A-CH-50/63V-120pF-J CC1-06A-RH-50/63V-330pF-J CC1-06A-RH-50/63V-330pF-J CC1-06A-RH-50/63V-330pF-J CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-470pF-J
F10DR27J-C F10DR27J-C F10DR27J-C F10DR47J-C F10DR47J-C F10DR47J-C F10F3R9J-C W11H3R9K W10J1R8K W11H270K W11H680K P10X180J-C V11D202B C2CF330J-T C2CF330J-T C2CF121J-T C2CF121J-T C2BF331K-T C2BF331K-T C2BF331K-T C2BF471K-T C2BF471K-T C2BF471K-T C2BF471K-T C2BF471K-T C2BF471K-T
53
Ref. No C732 C381 C323 C308 C311 C340 C401 C402 C481 C721 C861 C335 C324 C336 C162 C302 C309 C312 C313 C332 C362 C472 C475 C535 C703A C723 C744 C752 C756 C482 C405 C452 C451 C503 C504 C505 C506 C529 C543 C509 C527 C456 C943 C515A ! C598! C515 ! C548 C163A C172 C301 C307 C322
Part No. C2BF471K-T C2BF561K-T C2BF821K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF102K-T C2BF222K-T C2BF472K-T C2BF472K-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2BP101K-T C2BP221K-T C2BP102K-T C2BP392K-T C2BW102K-O C2BW102K-O C2BW102K-O C2BW102K-O C2BW471K-O C2RX471K-O C2RX681K-O C2RX681K-O C2EX102Z-O C2EX102Z-O C2EM102M-O C2EM102M-O C2EM102M-O E10C101M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T
Name Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor
Specification CC1-06A-RH-50/63V-470pF-J CC1-06A-RH-50/63V-560pF-J CC1-06A-RH-50/63V-820pF-J CC1-06A-RH-50/63V-1000pF-J CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-2200pF-K CT1-06A-2B4-50/63V-4700pF-K CT1-06A-2B4-50/63V-4700pF-K CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08C-2B4-500V-100PF-Z CT1-08C-2B4-500V-220F-Z CT1-08C-2B4-500V-1000pF-K CT1-08C-2B4-500V-3900pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-470pF-K CT81-08C-2R-2KV-470pF-K CT81-08C-2R-2KV-680pF-K CT81-08C-2R-2KV-680pF-K CT81-08C-2R-2KV-1000pF-K CT81-08C-2R-2KV-1000pF-K CTJ1-AC250V-470PF-20% CTJ1-AC250V-470PF-20% CTJ1-AC250V-1000PF-20% CD110-10V-100uF M CD110-16V-10uF M CD110-16V-10uF -M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF M
54
Ref. No C363 C364 C367 C751 C807 C841 C871 C745 C116 C171 C333 C352 C561 C723A C811 C823 C361 C743 C525 C532 C801 C406 C471 C471A C474 C474A C161 C522 C524 C453 C530 C121 C123 C372 C374 C153 C157 C163 C337 C804 C806 C813 C815 C825 C837 C339 C755 C303 C304 C325 C464 C703 C462
Part No. E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C220M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C101M-T E20C101M-T E20C471M-T E20C471M-T E20C471M-T E20D101M-T E20D101M-T E20D101M-T E20D101M-T E20D101M-T E20D471M E20D102M E20D222M E20E470M-T E20E331M-T E20FR47M-T E20FR47M-T E20FR47M-T E20FR47M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F2R2M-T E20F2R2M-T E20F4R7M-T E20F4R7M-T E20F4R7M-T E20F4R7M-T E20F220M-T E20F470M-T
Name Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor
Specification CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF -M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF -M CD110-16V-22uF -M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-470uF M CD110-16V-470uF M CD110-16V-470uF M CD110-25V-100uF -M CD110-25V-100uF -M CD110-25V-100uF -M CD110-25V-100uF -M CD110-25V-100uF -M CD110-25V-470uF -M CD110-25V-1000uF M CD110-25V-2200uF M CD110-35V-47uF -M CD110-35V-330uF -M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF -M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF -M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF -M CD110-50V-2.2uF M CD110-50V-2.2uF M CD110-50V-4.7uF M CD110-50V-4.7uF M CD110-50V-4.7uF M CD110-50V-4.7uF -M CD110-50V-22uF -M CD110-50V-47uF -M
55
Ref. No C466 C528B C477 C941 C458 C507 C326 C338 C365 C411 C331 C334 C404 C461 C321 C154 C158 C1515 C1517 C403 C408 C1513 C427 C1514 C460 C705 C706 C707 C467 C415 ! C501 ! L414 L351 L302 L331 L361 L751 Ref. No L752 L753 L401 L911 L912 L913 L501 ! N504 ! VD1001 VD171 VD461 VD462 VD482 VD561 VD734
Part No. E21H4R7M-T E20H101M E21K100M-T E21K100M-T E20H100M E20M101M F20F104J-T F20F104J-T F20F104J-T F20F104J-T F20F224J-T F20F224J-T F20F224J-T F20F474J-T F20G332J-T F20G562J-T F20G562J-T F22G123J-T F20G223K-T F20G333K-T F20G333K-T F20G473K-T F20G473K-T F20G104K-T F20G104K-T F20G104K-T F20G104K-T F20G104K-T F20J394J F20Z822J F20R224M LXXX0001 L2X239K-T L3X210K-T L3X2100K-T L3X2100K-T L3X2100K-T Part No. L3X2100K-T L3X2100K-T L3X2220K-T L3X2820K-T L3X2820K-T L3X2820K-T LMXX0002 RX0001XX DL0008XX DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T
Name Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Polypropylene capacitor Polypropylene capacitor Polypropylene capacitor H-linear Inductor Inductor Inductor Inductor Inductor Name Inductor Inductor Inductor Inductor Inductor Inductor Degaussing coil Photo electricity coupler LED Diode Diode Diode Diode Diode Diode
Specification CD110-160V-4.7uF -M CD110-160V-100uF-M CD110-250V-10uF -M CD110-250V-10uF -M CD110-160V-10uF -M CD293-400V-100uF-10% CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.22uF-K CL11-50V/63V-0.22uF-K CL11-50V/63V-0.22uF-K CL21-50V/63V-0.47uF-K CL11-100V-3300PF-K CL11-100V-5600PF-K CL11-100V-5600PF-K CL21X-100V-0.012uF-K CL11-100V-0.022uF-K CL11-100V-0.033uF-K CL11-100V-0.033uF-K CL11-100V-0.047uF-K CL11-100V-0.047uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CBB21-200V-0.3*9uF5% CBB81-1.6KV-8200PF-J CBB62-250VAC-0.22uF LH01 LGA0204-3.9uH-K LGA0204-1uH-K LGA0307-10uH-K LGA0307-10uH-K LGA0307-10uH-K Specification LGA0307-10uH-K LGA0307-10uH-K LGA0307-22uH-K LGA0307-82uH-K LGA0307-82uH-K LGA0307-82uH-K PC817B/C RED 5mm IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A
56
Ref. No VD911 VD921 VD931 VD1514 VD1516 VD1518 VD912 VD922 VD932 VD401 VD470 VD471 VD525 VD1517 VD503 VD504 VD505 VD506 VD436 VD472 VD524 VD521 VD543 VD300A VD481 VD564 VD1561 VD381 VD382 VD383 VD1519 Ref. No VD460 VD483 VD822 VD861A VD941 N703 N161 N505 N121 N801 N301 N401 N702 N503 V1511 V171 V542 V308 V911 V921 V931
Part No. DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0002XX-T DR0002XX-T DR0002XX-T DR0003XX-T DR0003XX-T DR0003XX-T DR0003XX-T DR0003XX-T DR0015XX-T DR0015XX-T DR0015XX-T DR0015XX-T DR0017XX DR0017XX DR0017XX DR0018XX DR0018XX DZ0001XX-T DZ0002XX-T DZ0006XX-T DZ0006XX-T DZ0011XX-T DZ0011XX-T DZ0011XX-T DZ0011XX-T Part No. DZ0010XX-T DZ0010XX-T DZ0010XX-T DZ0010XX-T DZ0010XX-T IXXX0080 IXXX0180 IXXX0118 IXXX0120 IXXX0120 IXXX0142 IXXX0173 IXXX0118 RXA1015X-T RXA1015X-T RXB892XX-T RXC1674X-T RXC2482X RXC2482X RXC2482X
Name Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Name Diode Diode Diode Diode Diode IC IC IC IC IC IC IC IC IC Audion Audion Audion Audion Audion Audion Audion
Specification IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A BAV21 BAV21 BAV21 FR105 FR105 FR105 FR105 FR105 TVR4N/TRM11C TVR4N/TRM11C TVR4N/TRM11C TVR4N/TRM11C RGP10J RGP10J RGP10J RGP15D RGP15D RD5.1EB3/HZ5C1 HZ22-2 RD3.3L/HZ3C3 RD6.4L/HZ6C2 RD7.1EB2/HZ7C1 RD7.1EB2/HZ7C1 RD7.1EB2/HZ7C1 RD7.1EB2/HZ7C1 Specification HZ9A3 HZ9A3 HZ9A3 HZ9A3 HZ9A3 upc574J/CW574 AN7522N TA78M05 5V LC4052B/CD4052B LC4052B/CD4052B TDA9381 LA78040 BR ST24C08-W TA78M08 8V 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SB892/2SB985T 2SC1674 2SC2482 2SC2482 2SC2482
57
Ref. No V913 V923 V933 V912 V922 V932 V450 V1512 V1513 V121 V122 V173 V351 V352 V354 V395 V504 V801 V1553 V451 V701 Z352 Z354 Z351 Z301 F501 ! A1001 A101 SW1001 SW1002 SW1003 SW1004 SW1005 SW1006 Z761
Part No. RXC421X RXC421X RXC421X RXC422X RXC422X RXC422X RXC2383X-T RXC3807X RXC5287X RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXD2140X RXC2369XX-T FC0007XX FC0008XX FC0006XX FXXX0020 RXXX0016 BXATB066 KXXX0101 KXXX0101 KXXX0101 KXXX0101 KXXX0101 KXXX0101 XC0004XX-A
Name Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Ceramic trap filter Ceramic trap filter Ceramic trap filter SAWF FUSE Remote receiver Tuner Touch switch Touch switch Touch switch Touch switch Touch switch Touch switch XTLO
Specification BF421/BF423 BF421/BF423 BF421/BF423 BF422/BF420 BF422/BF420 BF422/BF420 2SC2383-O 2SC3807/2SC5070 2SD1710/2SC4584/C5586 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E TT2190LS PH2369 XT6.0M XT5.5M XT6.5M K2966 38.9M 3.15A 250V HS0038 ET-5G1E-EV100 PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) 12.0MHz(18P)
58
CIRCUIT DIAGRAM