Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
hardware system structure, application scenarios, basic functions of modules and networking and configuration of the DBS3900
Page 2
Upon completion of this course, you will be able to: Know application scenarios of DBS3900 Master the hardware structure of DBS3900 Master the functions of different modules Master the cables connection rules of DBS3900 Know networking and configuration examples
Page 3
Page 4
DBS3900 Abbreviations
WMPT WBBPa WRFU UBFA UEIU UELP UFLP UPEU UTRP RCU CPRI AISG TMA SRXU APM WCDMA Main Processing and Transmission Unit WCDMA Baseband Process unit Type A WCDMA Radio Filter Unit Universal BBU Fan Unit Type A (2U) Universal Environment Interface unit Universal E1/T1 Lighting Protection unit Universal FE/GE Lighting Protection unit Universal Power and Environment Interface Unit Universal Transmission Processing Unit Remote Control Unit Common Protocol Radio Interface Antenna Interface Standard Group Tower Mounted Amplifier Slim Receive Unit Advanced Power Module
Page 5
Chapter1 General Description Chapter2 Hardware Introduction Chapter3 Networking and Configuration
Page 6
DBS3900 Overview
DBS3900 is a distributed NodeB of forth generation NodeB. DBS3900 system consists of:
TMA RF jumper
Feeder
Grounding cable
Power cable
BBU3900
RF jumper
Page 7
2G BTS RF Cable
Shelter
Air-conditioner
BBU
BBU3900+RRU+APM BBU3900+RRU+APM
Page 9
Launch a new 3G indoor site, there is an equipment room with limited space.
Page 10
Baseband unit
+
BBU3900 SRXU RRU3804 RRU3801E
Page 11
BBU3900 supports 24 cells, with 1,536 UL CEs and 1,536 DL CEs. One RRU3804 supports the 4-carrier configuration. When the NodeB expands from 1x1 to 1x4 or from 3x1 to 3x4, no extra RRU is required.
When using the 1.25 G optical module, cascading levels 4 When using the 2.5 G optical module, cascading levels 8
Page 12
Page 13
Chapter1 General Description Chapter2 Hardware Introduction Chapter3 Networking and Configuration
Page 14
Section2 RRU Hardware Section3 Section4 DBS3900 Cables Antenna and Feeder Subsystem
Page 15
Clock mode
Signaling Processing
Operation& Maintenance
Power mode
Decoding
Demodulation
Power Control information
FP Processing
RNC
TO RRU
Modulation
Page 16
Baseband unit
Typical configuration
BBU3900 Module
Mandatory boards and modules WMPT, WBBP, UBFA, and UPEU The optional boards are the UELP, UFLP, UTRP, and UEIU.
Page 17
Slot 0
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6 available
Slot 7 available
available available
available available
available available
available available
Page 18
Commissioning:RJ45
LEDs 4E1:DB26
Board number
maximum is 2 for one BBU mandatory board working in active and standby mode
Providing OM functions Controlling other boards in the system and providing the reference clock Providing USB ports for automatic NodeB upgraded Providing transmission port for Iub interface Providing OM channels
Page 19
Page 20
LED
Color
Description The connections are functional. The connections are faulty. There is ongoing data transmission. There is no data transmission. The connections are functional. The connections are faulty. There is ongoing data transmission. There is no data transmission.
LEDs beside the FE1 Green and FE0 optical port Yellow LEDs beside the ETH Green port Yellow
Page 21
SW1 for setting the E1/T1 working mode SW2 for setting the protection ground for the E1.
Settings of SW1 Bit T1 Mode 120-ohm E1 Balanced Mode OFF OFF ON ON 75-ohm E1 Unbalanced Mode ON ON ON ON
1 2 3 4
ON ON OFF OFF
Settings of SW2 Bit 120-ohm E1 Balanced Mode OFF OFF OFF OFF 75-ohm E1 Unbalanced Description Mode ON ON ON ON The RRING is for connected to the protection ground
1 2 3 4
Page 22
Providing the CPRI interface for communication between the BBU and the WRRU or WRFU Processing uplink and downlink baseband signals and support HSUPA and HSDPA function Supporting 1+1 backup of the CPRI interface According to the board chip processing capability, WBBP module include seven specifications. Current WBBP is the A version, called WBBPa.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 23
Page 24
45 HS-PDSCH codes 45 HS-PDSCH codes 45 HS-PDSCH codes 90 HS-PDSCH codes 90 HS-PDSCH codes All rights reserved
Controlling the fan speed Reporting the fan status to the WMPT Detecting the temperature of the fan board
Label STATE Color Green Status Description
0.125s ON, 0.125s The module is not registered, and no OFF 1s ON, 1s OFF alarm is reported.
The board is running properly.
Red
ON
Page 26
-48V to +12V
+24V to +12V
Converting -48 V or +24 V DC power input to +12 V DC power that is supported by boards Reporting alarms related to input and output under voltage Providing transmission ports for RS485 signals and 8 dry contact alarm signals
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 27
Label RUN
Color Green
Status ON OFF
Description The board is running properly. The board has no power input, or the board is faulty.
Socket and Port: The UPEU has one socket and four ports.
Quantity 1 1 1 1 1
Function DC power input Transmitting dry contact alarm signals Transmitting RS485 environment monitoring signals
Page 28
The UTRP provides ports for eight E1s/T1s and implements transport such as IP and ATM between the BBU3900 and the RNC.
4 E1:DB26
Label RUN
Color Green
Status ON OFF 1s ON, 1s OFF 0.125s ON, 0.125s OFF 2s ON, 2s OFF
Description The board has power input, yet the board is faulty. The board has no power input or is faulty. The board is running properly. Software is being loaded to the board. The board is under test. The board is in active mode. The board is in standby mode. The board is running properly. The board is reporting alarms and is faulty.
ACT
Green
ON OFF
ALM
Red
OFF ON
Page 29
UTRP board should add sub board to provide the different interface type WD22UTRP is the main board name. The UTRP has three sub-boards in current version
UAEU: Eight ATM over E1s/T1s UIEU: Eight IP over E1s/T1s UUAS: One unchannelized ATM over SDH/SONET(STM-1/OC-3) interface
The board in Transmission Sub board type gray tableInterface is not be delivered Board name name
WD22UEEU WD22UEOU WD22UAEU WD22UIEU WD22UCPU WD22UUPU WD22UCAU WD22UUAU WD22UEEC WD22UEOC WD22UAEC WD22UPEC WD22UCPS WD22UUPS WD22UCAS WD22UUAS FE/GE electrical board FE/GE optical board
currently
Interface specification 2*FE/GE (10/100/1000M adaptive) 2*FE/GE (10/100/1000M configured) 8* E1/T1 8*E1/T1 1*STM-1 1*STM-1 1*STM-1 1*STM-1
E1/T1 ATM interface sub board E1/T1 IP interface sub board Channelization IP optical sub board Unchanneliazation IP optical sub board Channelization ATM optical sub board Unchanneliazation ATM optical sub board
Page 30
maximum is 1
Connecting to an external monitoring device and transmitting RS485 signals to the WMPT Connecting to an external alarm device and transmitting dry contact alarm signals to the WMPT
Port : The UEIU has four ports.
Page 31
UELP
protection unit is an optional module of the BTS3900 cabinet (-48 V) or the power distribution cabinet.
The UFLP and the UELP
Page 32
The UELP can be optionally installed in the SLPU or the BBU. Each UELP supports the surge protection of 4-way E1/T1 signals. DB25 DB26
E1 Connection:
E1 E1
Indoor DDF
Page 33
DIP Switch S1
Description
Used for the 75 unbalanced mode Used for other modes except the 75 unbalanced mode
Page 34
IP Cable Connection.
Page 35
Section2 RRU Hardware Section3 Section4 DBS3900 Cables Antenna and Feeder Subsystem
Page 36
Interface module
Duplexer
MTRX
RX signaling Processing unit Extension interface LNA LNA Power module
BBU
CPRI
RX3 RX signaling Processing unit LNA LNA SRXU RX4 Antenna system
Page 37
RRU3804 Characteristics
Support 12dB, 24dB gain TMA RTWP statistic and report Standing wave detect and report Support ASIG (Antenna Interface Standards Group) 2.0 Receiver reference sensitivity typical value -125.5dBm RRU3804 connected to the SRXU supports 4-way RX diversity
Number of carrier 1 2 3 4
Page 38
14(RRU3804) / 12(RRU3801E)
NOTES:
The RRU3801E appearance (Panel and Ports) is the same with the RRU3804;
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 39
LEDs on RRU3804/RRU3801E-I
Label RUN Color Green Status ON OFF 1s on, 1s off 0.5s on, 0.5s off ALM Red ON OFF TX_ACT Green ON OFF Description The module has power input, yet the module is faulty The module has no power input or is reporting alarms The module is operational Software is being loaded to the module The module is reporting alarms (excluding VSWR-related alarms The module is operational The module is running No specific meaning
Page 41
LEDs on RRU3804/RRU3801E--II
Label VSWR Color Red Status ON OFF CPRI_W Red/gree ON (green) n ON (red) 0.5s ON, 0.5s OFF (red) OFF CPRI_E Red/gree ON (green) n ON (red) 0.5s ON, 0.5s OFF (red) OFF Description VSWR-related alarms are reported No VSWP-related alarm is reported The CPRI link is normal The optical module receives local alarms related to LOS The CPRI is out of lock The optical module is not in position or is powered off The CPRI link is normal The optical module receives local alarms related to LOS The CPRI is out of lock
Page 42
Item
Dimension wit h the housing Weight The weight of the SRXU :6KG Power input -48V DC Allowed voltage range -36 V DC to -57 V DC
Page 43
Socket for power supply Power Input From RRU Interconnection port between combined cabinets Port for RET antenna Grounding bolt
Page 44
RRU Configurations
The RRU is divided into two types according to output power and carries:
40 W RRU3801E, 40W output power on the top of cabinet 60 W RRU3804, 60W output power on the top of cabinet
RRU type RRU3804 RRU3801E RRU3804 RRU3801E RRU3804 RRU3804 RRU3801E RRU3801C RRU3801C Frequency band UMTS2100 UMTS2100 UMTS1900 UMTS1900 UMTS1.7/2.1G UMTS850 UMTS850 UMTS1800 UMTS900 Receiving Band 1920MHz 1980MHz 1920MHz 1980MHz 1850MHz 1910MHz 1850MHz 1910MHz 1710MHz 1755 MHz 824MHz 849MHz 824MHz 849MHz 1710MHz 1785MHz 880MHz 915 MHz Transmitting Band 2110MHz 2170MHz 2110MHz 2170MHz 1930MHz 1990MHz 1930MHz 1990MHz 2110 MHz 2155 MHz 869MHz 894MHz 869MHz 894MHz 1805MHz 1880MHz 925MHz 960MHz 4 2 4 2 4 4 2 2 2 Carriers
Page 45
Section2 RRU Hardware Section3 Section4 DBS3900 Cables Antenna and Feeder Subsystem
Page 46
Page 47
at the other end. Appropriate terminals are added to the bare end on site.
1) 3V3 connecter
2) OT terminals
Page 48
E1 Cable
FE Cable
Page 49
Installation Position
Page 50
the RET/PWR_SRXU port at the bottom of the RRU, and the other end is connected to the PWR_SRXU socket at the bottom of the SRXU.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 51
The CPRI optical cable is a multi-mode 2-wire cable with DLC connectors at both ends BBU and RRU CPRI hardware connection is same between RRU3801E and RRU3804
BBU3900
1) DLC connector
3) Fiber tail
Page 52
One end of the AISG multi-wire cable is a waterproof DB9 connector, and
Page 53
One end of the AISG extension cable is a standard AISG male connector,
Page 54
The RF jumper of the RRU3804/SRXU is of two types Antenna jumper: transmits and receives RF signals. Both
ends of the antenna jumper have DIN connectors
Interconnect jumper: transmits RF signals between two RRU3804s/SRXUs. The interconnect jumper is optional, depending on the site configuration. The interconnect jumper is 2 m long, and both ends have 2W2 connectors The 2W2 connectors at the two ends of the interconnect jumper are linked to the ports labeled RX_IN/OUT on two RRU3804s/SRXUs respectively
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 55 Waterproofed Joints
Page 56
BBU3900
Page 57
BBU3900
Page 58
Optical cable
BBU3900
Power cable
Page 59
Page 60
Section2 RRU Hardware Section3 Section4 DBS3900 Cables Antenna and Feeder Subsystem
Page 61
+ Roof station
(1) Directional antenna (2) Pole (3) Outdoor jumper
(4) Outdoor cable (5) Feeder clip (6) Feeder rack grounding kit (7) Outdoor grounding bar (8) To outdoor lightning protection ground (9) Feeder window
Page 62
+ Tower Station
(1) Lightning rod (4) Directional antenna (7) Feeder (10) Outdoor grounding bar (13) Guard rail (2) Pole (3) TMA
(5) Waterproof (6) Feeder curve grounding clip (8) Outdoor cable rack (11) Tower grounding conductor (9) Feeder window (12) Cable tie
Page 63
Page 64
Chapter1 General Description Chapter2 Hardware Introduction Chapter3 Networking and Configuration
Page 65
BBU Networking
BBUs and RNC can form multiple
Page 66
RRU Networking
BBUs and RRUs can form multiple networking modes such as star,
When using the 1.25 G optical module, cascading levels 4 When using the 2.5 G optical module, cascading levels 8
Page 67
Typical Configuration11
Applied to wide areas and indoor circumstances
RRU
BBU3900
Page 68
Typical Configuration21
Applied to long stretched areas
RRU
BBU3900
Page 69
Typical Configuration31/32
Applied to cities or other high capacity areas
RRU
cities
RRU
RRU
BBU3900
Page 70
Typical Configuration
configuration 3x1 3x2 3x3 3x4 Number of WBBPs 1 2 3 4 Number of RRU3804s (No TX Diversity) 3 3 3 3 Number of RRU3801Es (No TX Diversity) 3 3 6 6
Page 71
Thank You
www.huawei.com