Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
4/2/EN/1
Active
Chilled Beams
Type DID300B
TROX GmbH
Heinrich-Trox-Platz
D-47504 Neukirchen-Vluyn
Contents Description
Contents Description
Construction
Casing arrangements
Dimensions
Assembly
2
3
4
5
6
DID300B-...-V
Top entry air connection spigot
Nomenclature
Performance overview cooling
with 2-pipe and 4-pipe systems
Performance overview heating
with 4-pipe systems
Aerodynamic data
Order details
8
9
10
11
12
DID300B-...-H
Side entry air connection spigot
Description
TROX Active Chilled Beams type DID300B use a combination of
air and water systems. They combine the air flow characteristics
of ceiling diffusers with the energy benefits of load dissipation
using water (heating/cooling).
The primary air volume flow required for fresh air supply enters
the upper plenum box through a connecting spigot and is then
discharged into the mixing zone via nozzles which are fitted into
a diaphragm plate.
The induced air is drawn from the room through a water coil. In
the mixing section of the DID300B the induced air is mixed with
the primary air and the total discharged into the room via slots.
The DID300B can be used for cooling and/or heating.
An additional spigot for extract of exhaust air can be fitted
adjacent to the primary air duct (supply and extract air
construction).
Caution !
The cold water supply temperature must be selected such
that it never falls below room dewpoint.
Max. pressure:
for 2-pipe and 4-pipe system
6 bar at 90C
7 bar at 20C
Other operating pressures available on request!
The type DID300B chilled beams are particularly suitable for use
in low ceiling void spaces because of their shallow construction.
Thus they are suitable not only for use in new buildings but are
also excellent for refurbishment projects.
When connected appropriately, they can be used for both
individual room control or form a grouped zone control.
The DID300B is available with either top or side entry air
connection spigot for supply and extract air.
Between the upper and lower casing there is a diaphragm plate
which contains two longitudinal rows of nozzles. These discharge nozzles are available in three different sizes, the selection
depending on the volume flow rates required.
The induction grille can easily be removed for cleaning purposes.
Materials
Casing, including the top plenum and perforated plate induction
grille are made of galvanised steel sheet.
The standard finish of the casing and the induction grille is
powder-coated white (RAL 9010), the top casing (plenum) and
coil remain untreated - optionally can be finished in black
(RAL 9005), nozzle plate only finished in black (RAL 9005).
The heat exchanger consists of copper tubes with formed
aluminium fins. The flexible hose, available as an accessory, is
made of special plastic with stainless steel sheathing.
Construction
IEE LN 900 to 1800 = 123
OE L 2100 to 3000 = 158
P N
L1
LL
LR
LH
293
293
LH
L1
LR
LH
LL
LR
LH
293
293
LL
100
L1
100
View A - A
Construction with top entry supply air spigot
View B - B
Construction with side extract air spigot
10b
210
D
18
123
18
293
45
193
98
195
50
1a
264
38
293
View A - A
Construction with side entry supply air spigot
View B - B
Construction with top extract air spigot
210
98
18
143
123
10a
50
210
1b
36
10a
10b
18
1a
1b
36
299
293
293
Casing arrangements
V-L
V-M
V-R
H - SH
H - LV
H - LH
H - MV
H - MH
H - RV
H - RH
Casing arrangement with top entry supply and extract air spigot
V - L - AR
V - R - AL
V - M - AR
V - M - AL
Casing arrangement with side entry supply and extract air spigot
H - LV - ARV
H - RV - ALV
H - MV - ARV
H - MV - ALV
H - LH - ARH
H - RH - ALH
H - MH - ARH
H - MH - ALH
H - LV - ARH
H - RV - ALH
H - MV - ARH
H - MV - ALH
H - LH - ARV
H - RH - ALV
H - MH - ARV
H - MH - ALV
Dimensions
V-S
H - SV
H - SH
Supply air
LH
LL
LR
V - L - AR
L1
H - LV - ARH
min
max
min
max
min
max
900
800
40
43
54
58
893
900
1200
1100
40
43
54
58
1193
1200
1500
1400
40
43
54
58
1493
1500
1800
1700
40
43
54
58
1793
1800
2100
2000
40
43
54
58
2093
2100
2400
2300
40
43
54
58
2393
2400
2700
2600
40
43
54
58
2693
2700
3000
2900
40
43
54
58
2993
3000
V-L
Supply air
H - LV
H - LH
900
1200
LH
LL
800
1100
LR
43
43
L1
min
max
min
max
58
58
658
658
901
1201
1500
1800
1500
1800
1400
1700
43
43
58
58
658
658
1501
1801
2100
2400
2100
2400
2700
2000
2300
2600
43
43
43
58
58
58
658
658
358
2101
2401
2701
2700
3000
3000
V-M
Supply air
H - LH - ARV
H - LH - ARH
Supply and
extract air
left
LN
LH
LL
min
max
min
max
900
1200
800
1100
43
43
253
253
658
658
1096
1396
1500
1800
1500
1800
1400
1700
43
43
253
253
658
658
1696
1996
2100
2400
2100
2400
2700
2000
2300
2600
43
43
43
253
253
253
658
658
358
2296
2596
2896
2700
3000
3000
LR
L1
left
LN
H - LV - ARV
H - MV
H - MH
V - M - AL
H - MV - ALV
H - MH - ALV
H - MH - ARV
V - M - AR
H - MH - ARH
Supply and
extract air
LN
H - MV - ARV
middle
LH
L1
min
max
900
1200
800
1100
1290
1590
1800
1800
1500
1800
1400
1700
1890
2190
2100
2400
2100
2400
2000
2300
2490
2790
2700
3000
middle
V - R - AL
LN
900
1200
LH
L1
800
1100
H - RV - ALV
H - RV - ALH
min
max
901
1201
1500
1800
Supply and
extract air
LH
H - RH - ALV
H - RH - ALH
right
LL
LR
L1
1500
1800
1400
1700
1501
1801
2100
2400
LN
min
max
min
max
2100
2400
2700
2000
2300
2600
2101
2401
2701
2700
3000
3000
900
1200
800
1100
238
238
643
643
58
58
1095
1395
1500
1800
1500
1800
1400
1700
238
238
643
643
58
58
1695
1995
2100
2400
2100
2400
2700
2000
2300
2600
238
238
238
643
643
343
58
58
58
2295
2595
2895
2700
3000
3000
V-R
Supply air
H - RV
H - RH
right
LN
LH
LL
LR
min
max
L1
min
max
900
1200
800
1100
43
43
643
643
58
58
901
1201
1500
1800
1500
1800
1400
1700
43
43
643
643
58
58
1501
1801
2100
2400
2100
2400
2700
2000
2300
2600
43
43
43
643
643
343
58
58
58
2101
2401
2701
2700
3000
3000
Assembly
Assembly
The two long sides of the DID300B are each provided with
two suspension holes or for L1 = 1500 4 holes are provided on
each side. The assembly is installed on site using wire or metal
hangers which must have the Building Authority certificate of
approval. When the DID300B has been installed, 4 locking
devices can be loosened with a screw driver (detail X) and the
whole induction grille can be lowered down lengthways. The
induction grille is supported by two safety cables.
Detail X
12
196
293
35
L1
Locking
device
Safety cable
Detail Y
48
26
Available connectors
32
32
Suspension holes
FS12-S
FS12-S/A
60
R8
FS12-S/U
49
Installation
The DID300B unit is fitted with a border extrusion which is
suitable for the usual range of ceiling constructions. This ensures
the best possible ceiling design.
B = Grid width
R = Grid pitch
Grid
18
30 or 40 mm
(AW)*
Support angle
293
L1
R
18
293
L1
18
293
L1
Nomenclature
WK
WH
WH
WK
tWRK
tWVH
tWRH
tVWK
LN + 300 mm
Top entry
connection
Side entry
connection
LN
1,7
1.7 m
m
Pr
Pr
tPr
L; tL
DID300B
H1; tH1
F
room
LLraum
tL
in K:
tH1
in K:
Temp. diff. between room air tR and core tH1 at distance L = A/2 + H1
tPr
in K:
tZ
in K:
Temp. diff. between room air and supply air into space
tW
in K:
tRWV
in K:
pt
in Pa:
pW
in kPa:
tR
in C:
Room temperature
tWVK
in C:
tWRK
in C:
tWVH
in C:
tWRH
in C:
tPr
in C:
WK
in W:
WH
in Watt:
ges
in Watt:
Pr
in Watt:
S
in Watt:
Water side thermal capacity (for cooling S = WK, for heating S = WH)
Zul
in W/m2:
WK
in l/h:
WH
in l/h:
Zul
in l/s:
Pr
in l/s:
in m/s:
H1
in m/s:
LWA
in dB(A):
ges
Zul
in m:
in m:
Horizontal plus vertical distance from diffuser, discharge down the wall L = X + H1
Xkrit
in m:
Horizontal distance from diffuser at which the supply air begins to separate from ceiling
H1
in m:
in m:
in m:
LN
in mm:
in m2:
Nominal length
Reference area (LN + 0.3) x 5
5000 mm
H1
LN
900
1200
1500
1800
2100
2400
2700
3000
50
70
90
110
140
180
200
250
0.71
0.69
0.68
0.67
0.55
0.53
0.52
0.51
0.85
0.83
0.82
0.81
0.67
0.66
0.64
0.63
0.94
0.93
0.93
0.92
0.76
0.75
0.74
0.73
1.00
1.00
1.00
1.00
0.83
0.82
0.81
0.80
1.07
1.07
1.08
1.09
0.90
0.90
0.89
0.89
1.12
1.14
1.15
1.16
0.97
0.97
0.97
0.97
1.14
1.15
1.18
1.19
1.00
1.00
1.00
1.00
1.18
1.20
1.23
1.25
1.05
1.05
1.05
1.05
tW in K
WK in l/h
Reference values
tWVK = tPr = 16C
WK = 110 l/h (LN 900 up to 1800)
WK = 200 l/h (LN 2100 up to 3000)
tPr = tPr tR = 10 K
tRWV = tWVK tR = 10 K
LN
Type of
nozzles
K
900
M
G
K
1200
M
G
K
1500
M
G
K
1800
M
G
K
2100
M
G
K
2400
M
G
K
2700
M
G
K
3000
M
G
.
V Pr
50 l/h 60
70
80
90 100
110
7.5
7.0
6.5
6.0
150
5.5
5.0
4.5
200
4.0
3.5
250
3.0
2.5
WK
2.0
1.5
1.0
0.5
0.0
200 300 400 500 600 700 800 900 1000 1100
pW in kPa
8.5
8.0
Correction factors
16
15
14
12
12
11
10
9
8
7
II
3000
2800
2400
2100
1800
1500
1200
900
LN
6
5
4
3
2
1
0
40
WK in l/h
WK in W
l/s
m3/h
.
Q Pr
(air)
watts
3
7
11
6
13
19
11
19
27
3
8
13
8
15
23
15
23
30
4
9
15
10
18
26
19
25
32
5
11
17
12
21
29
22
29
36
6
12
18
14
23
32
26
32
38
7
13
19
16
25
34
30
35
40
8
14
21
18
27
37
34
37
41
9
16
23
20
30
39
38
40
43
11
25
40
22
47
68
40
68
97
11
29
47
29
54
83
54
83
108
14
32
54
36
65
94
68
90
115
18
40
61
43
76
104
79
104
130
22
43
65
50
83
115
94
115
137
25
47
68
58
90
122
108
126
144
29
50
76
65
97
133
122
133
148
32
58
83
72
108
140
137
144
155
36
84
133
72
157
229
133
229
326
36
96
157
96
181
277
181
277
362
48
109
181
121
217
314
229
301
386
60
133
205
145
253
350
265
350
434
72
145
217
169
277
386
314
386
458
84
157
229
193
301
410
362
422
482
96
169
253
217
326
446
410
446
494
109
193
277
241
362
470
458
482
518
.
QS
(water)
watts
.
Q ges
tW
.
q Zul
.
VPr /m2
watts
W/m2
l/(s m2)
m3/(h m2)
116
256
324
156
291
352
201
295
351
79
303
399
202
347
437
267
363
418
113
342
466
245
412
504
329
404
468
146
406
527
287
472
565
374
462
526
199
515
681
377
609
750
503
598
673
235
555
729
425
659
807
571
650
715
270
592
797
471
707
873
637
684
741
304
664
863
517
773
922
701
732
775
152
340
457
229
448
581
334
524
676
115
399
556
298
528
714
448
640
780
161
451
647
366
629
818
559
706
854
206
539
732
432
725
915
639
811
960
271
660
898
546
886
1136
817
984
1131
319
711
958
618
961
1217
933
1072
1198
366
761
1050
688
1033
1319
1047
1131
1235
413
857
1140
758
1135
1393
1159
1214
1294
0.9
2.0
2.5
1.2
2.3
2.7
1.6
2.3
2.7
0.6
2.4
3.1
1.6
2.7
3.4
2.1
2.8
3.3
0.9
2.7
3.6
1.9
3.2
3.9
2.6
3.2
3.7
1.1
3.2
4.1
2.2
3.7
4.4
2.9
3.6
4.1
0.9
2.2
2.9
1.6
2.6
3.2
2.2
2.6
2.9
1.0
2.4
3.1
1.8
2.8
3.5
2.5
2.8
3.1
1.2
2.5
3.4
2.0
3.0
3.8
2.7
2.9
3.2
1.3
2.9
3.7
2.2
3.3
4.0
3.0
3.1
3.3
25
57
76
38
75
97
56
87
113
15
53
74
40
70
95
60
85
104
18
50
72
41
70
91
62
78
95
20
51
70
41
69
87
61
77
91
23
55
75
45
74
95
68
82
94
24
53
71
46
71
90
69
79
89
24
51
70
46
69
88
70
75
82
25
52
69
46
69
84
70
74
78
0.5
1.2
1.8
1.0
2.2
3.2
1.8
3.2
4.5
0.4
1.1
1.7
1.1
2.0
3.1
2.0
3.1
4.0
0.4
1.0
1.7
1.1
2.0
2.9
2.1
2.8
3.6
0.5
1.0
1.6
1.1
2.0
2.8
2.1
2.8
3.4
0.5
1.0
1.5
1.2
1.9
2.7
2.2
2.7
3.2
0.5
1.0
1.4
1.2
1.9
2.5
2.2
2.6
3.0
0.5
0.9
1.4
1.2
1.8
2.5
2.3
2.5
2.7
0.5
1.0
1.4
1.2
1.8
2.4
2.3
2.4
2.6
1.8
4.2
6.6
3.6
7.8
11.4
6.6
11.4
16.2
1.4
3.8
6.2
3.8
7.2
11.0
7.2
11.0
14.4
1.6
3.6
6.0
4.0
7.2
10.4
7.6
10.0
12.8
1.7
3.8
5.8
4.1
7.2
9.9
7.5
9.9
12.3
1.8
3.6
5.4
4.2
6.9
9.6
7.8
9.6
11.4
1.9
3.5
5.1
4.3
6.7
9.1
8.0
9.3
10.7
1.9
3.4
5.0
4.3
6.5
8.9
8.2
8.9
9.8
2.0
3.5
5.0
4.4
6.5
8.5
8.3
8.7
9.4
Pt
(air)
Pa
< 20
32.5
45.1
< 20
34.0
44.6
< 20
32.0
41.7
< 20
31.4
44.9
< 20
33.1
45.0
22.5
34.4
41.8
< 20
30.9
45.1
< 20
34.4
44.6
26.9
34.5
41.4
< 20
34.3
46.5
< 20
34.5
43.5
26.1
33.8
39.8
< 20
34.1
45.4
20.6
34.4
43.6
29.2
35.0
39.8
< 20
34.1
44.7
22.0
34.5
43.0
31.9
36.2
39.9
< 20
34.2
45.5
23.3
34.6
43.4
34.2
36.6
39.4
20.1
36.1
46.2
24.4
35.7
43.0
36.3
37.7
39.7
29
156
386
24
112
239
25
75
151
17
124
326
24
85
201
28
65
110
21
106
294
25
80
167
30
51
84
24
115
275
25
76
146
28
49
76
26
105
236
25
68
132
30
46
64
28
98
208
25
62
115
31
43
56
30
92
207
26
58
108
33
39
47
32
100
207
26
58
98
34
37
43
< 20
32.5
45.1
< 20
35.0
45.6
20.8
36.0
45.7
< 20
31.4
44.9
< 20
34.1
46.0
26.5
38.4
45.8
< 20
30.9
45.1
< 20
35.4
45.6
30.9
38.5
45.4
< 20
33.3
45.5
21.0
36.5
45.5
32.1
39.8
45.8
< 20
33.1
44.4
22.6
36.4
45.6
35.2
41.0
45.8
< 20
33.1
43.7
24.0
36.5
45.0
37.9
42.2
45.9
< 20
33.2
44.5
25.3
36.6
45.4
40.2
42.6
45.4
< 20
35.1
45.2
26.4
37.7
45.0
42.3
43.7
45.7
PW
(water)
kPa
1.3
1.7
2.0
2.3
7.6
8.5
9.3
10.2
Correction factors
50
70
90
110
130
150
0.70
0.70
0.69
0.69
0.47
0.46
0.45
0.44
1.00
1.00
1.00
1.00
0.68
0.67
0.67
0.66
1.18
1.19
1.20
1.21
0.83
0.82
0.81
0.81
1.30
1.32
1.34
1.35
0.93
0.93
0.92
0.92
1.38
1.41
1.43
1.45
1.00
1.00
1.00
1.00
1.44
1.47
1.50
1.53
1.06
1.06
1.06
1.06
1.49
1.52
1.56
1.59
1.10
1.10
1.11
1.11
Reference values
Type of
nozzles
K
900
M
G
K
1200
M
G
K
1500
M
G
K
1800
M
G
K
2100
M
G
K
2400
M
G
K
2700
M
G
K
3000
M
G
10
50 l/h 60
III
70 80
90
100
110
4.0
IV
3000
2800
3.5
12
2400
150
10
8
200
250
WH
3.0
2100
2.5
1800
1500
2.0
1200
900
1.5
LN
1.0
tR
= tPr = 22C (isothermal)
WH = 50 l/h (LN 900 up to 1800)
WH = 110 l/h (LN 2100 up to 3000)
tRWV = tWVH tR = 28 K
LN
14
pW in kPa
LN
900
1200
1500
1800
2100
2400
2700
3000
4.5
16
30
tW in K
WH in l/h
.
V Pr
l/s
m3/h
.
.
Q S = Q ges
(water)
watts
3
7
11
6
13
19
11
19
27
3
8
13
8
15
23
15
23
30
4
9
15
10
18
26
19
25
32
5
11
17
12
21
29
22
29
36
6
12
18
14
23
32
26
32
38
7
13
19
16
25
34
30
35
40
8
14
21
18
27
37
34
37
41
9
16
23
20
30
39
38
40
43
11
25
40
22
47
68
40
68
97
11
29
47
29
54
83
54
83
108
14
32
54
36
65
94
68
90
115
18
40
61
43
76
104
79
104
130
22
43
65
50
83
115
94
115
137
25
47
68
58
90
122
108
126
144
29
50
76
65
97
133
122
133
148
32
58
83
72
108
140
137
144
155
184
399
502
246
452
543
316
457
542
125
469
613
316
536
668
416
559
642
178
529
711
383
632
767
509
621
714
229
624
800
446
720
854
575
705
798
379
965
1264
711
1135
1388
943
1114
1249
446
1037
1350
799
1226
1488
1066
1208
1326
512
1104
1471
884
1311
1605
1185
1271
1371
576
1235
1587
967
1428
1692
1299
1355
1432
0.5
0
200 400 600 800 1000 1200 1400 1600 1800 2000
0
50 60 70 80 90 100 110 120 130 140 150 160 170
WH in W
WH in l/h
.
VPr /m2
tW
.
q Zul
W/m2
l/(s m2)
m3/(h m2)
3.2
6.9
8.6
4.2
7.8
9.3
5.4
7.9
9.3
2.2
8.1
10.5
5.4
9.2
11.5
7.2
9.6
11.0
3.1
9.1
12.2
6.6
10.9
13.2
8.8
10.7
12.3
3.9
10.7
13.8
7.7
12.4
14.7
9.9
12.1
13.7
3.0
7.5
9.9
5.6
8.9
10.8
7.4
8.7
9.8
3.5
8.1
10.6
6.2
9.6
11.6
8.3
9.4
10.4
4.0
8.6
11.5
6.9
10.3
12.5
9.3
9.9
10.7
4.5
9.7
12.4
7.6
11.2
13.2
10.2
10.6
11.2
31
66
84
41
75
90
53
76
90
17
63
82
42
72
89
55
75
86
20
59
79
43
70
85
57
69
79
22
59
76
43
69
81
55
67
76
32
80
105
59
95
116
79
93
104
33
77
100
59
91
110
79
89
98
34
74
98
59
87
107
79
85
91
35
75
96
59
87
103
79
82
87
0.5
1.2
1.8
1.0
2.2
3.2
1.8
3.2
4.5
0.4
1.1
1.7
1.1
2.0
3.1
2.0
3.1
4.0
0.4
1.0
1.7
1.1
2.0
2.9
2.1
2.8
3.6
0.5
1.0
1.6
1.1
2.0
2.8
2.1
2.8
3.4
0.5
1.0
1.5
1.2
1.9
2.7
2.2
2.7
3.2
0.5
1.0
1.4
1.2
1.9
2.5
2.2
2.6
3.0
0.5
0.9
1.4
1.2
1.8
2.5
2.3
2.5
2.7
0.5
1.0
1.4
1.2
1.8
2.4
2.3
2.4
2.6
1.8
4.2
6.6
3.6
7.8
11.4
6.6
11.4
16.2
1.4
3.8
6.2
3.8
7.2
11.0
7.2
11.0
14.4
1.6
3.6
6.0
4.0
7.2
10.4
7.6
10.0
12.8
1.7
3.8
5.8
4.1
7.2
9.9
7.5
9.9
12.3
1.8
3.6
5.4
4.2
6.9
9.6
7.8
9.6
11.4
1.9
3.5
5.1
4.3
6.7
9.1
8.0
9.3
10.7
1.9
3.4
5.0
4.3
6.5
8.9
8.2
8.9
9.8
2.0
3.5
5.0
4.4
6.5
8.5
8.3
8.7
9.4
Pt
(air)
Pa
< 20
32.5
45.1
< 20
34.0
44.6
< 20
32.0
41.7
< 20
31.4
44.9
< 20
33.1
45.0
22.5
34.4
41.8
< 20
30.9
45.1
< 20
34.4
44.6
26.9
34.5
41.4
< 20
34.3
46.5
< 20
34.5
43.5
26.1
33.8
39.8
< 20
34.1
45.4
20.6
34.4
43.6
29.2
35.0
39.8
< 20
34.1
44.7
22.0
34.5
43.0
31.9
36.2
39.9
< 20
34.2
45.5
23.3
34.6
43.4
34.2
36.6
39.4
20.1
36.1
46.2
24.4
35.7
43.0
36.3
37.7
39.7
29
156
386
24
112
239
25
75
151
17
124
326
24
85
201
28
65
110
21
106
294
25
80
167
30
51
84
24
115
275
25
76
146
28
49
76
26
105
236
25
68
132
30
46
64
28
98
208
25
62
115
31
43
56
30
92
207
26
58
108
33
39
47
32
100
207
26
58
98
34
37
43
< 20
32.5
45.1
< 20
35.0
45.6
20.8
36.0
45.7
< 20
31.4
44.9
< 20
34.1
46.0
26.5
38.4
45.8
< 20
30.9
45.1
< 20
35.4
45.6
30.9
38.5
45.4
< 20
33.3
45.5
21.0
36.5
45.5
32.1
39.8
45.8
< 20
33.1
44.4
22.6
36.4
45.6
35.2
41.0
45.8
< 20
33.1
43.7
24.0
36.5
45.0
37.9
42.2
45.9
< 20
33.2
44.5
25.3
36.6
45.4
40.2
42.6
45.4
< 20
35.1
45.2
26.4
37.7
45.0
42.3
43.7
45.7
PW
(water)
kPa
0.12
0.14
0.16
0.18
0.85
0.93
1.02
1.11
Aerodynamic data
900
1200
1500
1800
2100
2400
2700
3000
0.92
0.96
1.0
1.04
1.07
1.11
1.14
1.17
0.87
0.94
1.0
1.05
1.09
1.13
1.17
1.20
Nozzle type K
Nozzle type K
H1 0.8
0.60
6
4 -
0.07
0.30
-4
0.06
0.25
0.05
2.0
3.0
0.018
0.016
0.014
VI
0.04
6.0
4.0
0.012
1.0
Distance L or Xkrit in m
0.09
-8
0.07
K
-6
0.30
K
-4
0.06
0.05
0.25
1.0
3.0
0.016
VIII
0.04
6.0
4.0
1.0
Distance L or Xkrit in m
1.5
2.0
0.040
0.55
0.22
tL/tZ
0.50
0.20
0.18
0K
K
-8
0.14
-
0.30
6K
r=
K
-4
16
tL/tZ
1.5
2.0
0.10
12
0.20
1.0
l/s
0.
IX
0.12
15
14
0.25
18
3.0
H1 in m/s
-1
0.35
4.0
Distance L or Xkrit in m
0.08
6.0
18
l/s
0.030
0.
0 0
0
20 .25 .30 .40
0.16
tL / tZ
at
t
Z
0.035
r=
16
14
12
kr
it
0.012
6.0
1.2 1.6 2m
0.24
0.40
4.0
Nozzle type G
H1 0.8
0.60
0.45
3.0
Spacing A or A/2 + H1 in m
Nozzle type G
L in m/s
0.020
0.018
10
2.0
0.022
0.
1.5
0.024
0.014
VII
0.20
0.026
l/s
0 0
20 .25 .30
0.08
K
12
10
0.
-1
r=
0.
15
0.35
at Xkrit
t
Z
0.10
H1 in m/s
0.40
6.0
0.030
tL/tZ
P
tL / tZ
l/s
10
4.0
1.2 1.6 2m
0.11
tL/tZ
12
3.0
tH1 / tZ
0.45
L in m/s
H1 0.8
0.12
0.50
2.0
Nozzle type M
0.60
r=
1.5
Spacing A or A/2 + H1 in m
Nozzle type M
0.55
0.020
0.026
0.024
0.022
tH1 / tZ
1.5
0.022
0.
0.20
1.0
0.024
m
tL/tZ
10
0 0
20 .25 .30
-8
0.08
0.
0.35
l/s
0.09
-1
15
at Xkr
t it
Z
0.45
0.026
r=
0.
l/s
0.40
0.10
tH1 / tZ
r=
tL/tZ
H1 in m/s
0.50
0.030
0.11
tL / tZ
0.55
L in m/s
1.2 1.6 2m
0.12
0.020
0.018
0.016
1.0
1.5
2.0
3.0
4.0
6.0
Spacing A or A/2 + H1 in m
11
Order details
Specification text
Support angles and flexible hoses are available as accessories for the
DID300B unit.
The active chilled beam type DID300B is suitable for dealing with
high internal heat loads using a combination of air and water.
It consists of the top plenum which serves as primary air duct and
a diaphragm plate with nozzles in two longitudinal rows (different
nozzle sizes are available). A coil is fitted underneath the primary air
plenum and diaphragm plate. The induction grille below the coil is a
perforated plate. The coil can be used either for heating or cooling
(2-pipe system) as well as heating and cooling (4-pipe system).
The external diameter of the bare coil tube ends is 12 mm. Primary
and conditioned induced air are mixed in the unit and discharged
horizontally with coanda effect into the room via the two slots formed
by the external frame and the internal extrusions. There are holes in
the casing to enable the unit to be hung by the customer.
A construction incorporating an extract air spigot can be provided.
Spigots for supply and extract air can be either side or top mounted.
Materials
Casing, including the top plenum and perforated plate induction grille
are made of galvanised steel sheet.
The standard finish of the casing and the induction grille is powdercoated white (RAL 9010), the top casing (plenum) and coil remain
untreated optionally can be finished in black (RAL 9005), nozzle
plate only finished in black (RAL 9005).
The heat exchanger consists of copper tubes with formed aluminium
fins. The flexible hose, available as an accessory, is made of special
plastic with stainless steel sheathing.
Order code
These codes do not need to be completed for standard products
DID300B - 2 - K - H - SV - ALV
1800 x 1500
P1
RAL 9016
/ G3
EI
EE
OEE
EE
EE
PE
Coil:
Two-pipe
Four-pipe
2
4
Nozzle options:
small
K
medium
M
large
G
900 x 900
1200
1500
1800 1)
1200 x 1200
1500
1800
1500 x 1500
1800
2100
1800 x 1800
2100
2400
2100 x 2100
2400
2700
2400 x 2400
2700
3000
2700 x 2700
3000
3000 x 3000
L1 x LN
(mm)
IEE
OE
P
IE
EEO
EE
EP
IE
EEO
EE
EP
Accessory:
FS12-... (see table)
AW = Support angle
Not used
TE
EE
EE
EZE
EE
EE
EU
TE Coil finish:
EE
EE
EZE 0 Standard untreated
EE
EE G3 Finished
UE to RAL 9005
Standard finish
Powder-coated to RAL 9010
(GE 50%) 2)
P1 Powder-coated to RAL . . .
(GE 70%) 2)
Note:
L1 = 893 ... 3000 mm
LN only available in standard length
L1 maximum 7 mm shorter than LN
combination
FS12-S
FS12-S/U
length in mm
Order example
500, 750, 1000
FS12-S/A
12
Make: TROX
Type: DID300B-2-K -H-SV-ALV / 1800 x 1500 / P1 / RAL 9016 / G3