Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
BLANK
Table of Contents
Rolled Ball Screw R Series - Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Rolled Ball Screws - Reference Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Rolled Ball Screws RNFTL - Flanged Nut (fine, medium lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 4 to 7 Rolled Ball Screws RNFTL - Flanged Nut (high helix lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 8 & 9 Rolled Ball Screws RNFBL - Flanged Nut (fine, medium lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 10 & 11 Rolled Ball Screws RNCT - Nut with V-thread (fine lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 12 & 13 Rolled Ball Screws RNSTL - Square Nut (fine, medium lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 14 & 15 Rolled Ball Screws RNFCL - Flanged Nut (high helix lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 16 & 17 Rolled Ball Screws RNFCL - Flanged Nut (ultra high helix lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 18 & 19 Shaft End Configuration of a Rolled Ball Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 20 & 21 Ball Screw Support Units - Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 22 Ball Screw Support Units - Reference Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 23 Ball Screw Support Units - Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 24 Ball Screw Support Units - Light Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 25 to 31 Ball Screw Support Units - Heavy Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 32 to 35 Installation of Ball Nut on Rolled Screw Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 36 Installation of Ball Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 37 to 39 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 40 Other Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 41 Unit Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 41 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 42 to 44
Table 1 Classification of rolled ball screws Nut model Nut shape Recirculation system Lead classification
Fine, medium lead High helix lead
Page
RNFTL
RNFBL
Flanged Circular
10
RNCT
Fine lead
12
RNSTL
Square type
14
RNFCL
Flanged Circular
16
18
(2) Features
Short delivery time: R Series is standardized, and available in stock. Interchangeable screw shaft and ball nut: Screw shaft and nut assembly components are sold separately, and randomly-matched. The maximum axial play after assembly is shown in the dimension tables (from Page 6 ~ 8). Low prices: Screw shaft is processed by rolling. This is why prices are lower than those of precision types. Abundant series: There are 128 types of nut assembly combinations in the series. Each combination has two to three different lengths in screw shaft.
(3) Accuracy
Lead accuracy: Ct10 grade (v300 =0.210). Axial play: Varies with internal specification. Refer to the dimension tables (Page 6). Run out of screw shaft center: Ct10 grade.
RN FTL 25 10 A 5 S
Product code (rolled nut) Nut model FTL, FBL, STL, CT, FCL Screw shaft diameter (mm) Internal design code Lead (mm) Seal code S: With seal No code: Without seal Effective turns of balls (turns of balls x number of circuit)
RS 25 10 A 20
Product code (Rolled screw shaft) Screw shaft diameter (mm) Screw shaft length (x 100 mm) Internal design code Lead (mm)
Lead (mm) 10 12 16 20 25 32 40 50 64 80
14
14 6 8 14 18
10 14 10 14
8 14 8 14
18 18
6 12
10 14 10 14 12 10 4 12 4 12 14 4 12
8 14
18
8 14
18
14
Shaft diameter
Lead
Ball diameter
Root diameter
d
10 10 12 14 14 16 18 20 20 25
l
3 6 8 4 5 10 8 5 10 5
Dw
2.381 2.381 2.778 2.778 3.175 3.175 4.762 3.175 4.762 3.175
dm
10.65 10.65 12.65 14.5 14.5 16.75 18.5 20.5 21.25 25.5
dr
8.1 8.1 9.6 11.5 11.0 13.3 13.6 17.0 16.2 22.0
Static C oa
6730 4810 6560 10800 9720 11500 25800 14200 21800 36300 35200
25
10
6.35
26
0.20
44
Remarks 1. Protruding portion of the tube does not have any interference with the ball nut housing if its dimensions corresponding to U and V are large enough. 2. The actual screw shaft length may become slightly longer than nominal length Ls due to manufacturing tolerance. 3. Seals are provided in the nut. Therefore, the external dimensions of those with the seals are the same as those without. In the side view drawing of the ball nut, above the center line is with seal, and beneath is without seal. Seals for ball nuts with the shaft diameter of 14 mm or less are made of synthetic resin. Seals for those of 16 mm or over are "Brush-seal."
Unit: mm
A
40 40 45 50 50 53 63 60 67 71 80 80
Flange G
15 15 19 19 22 23 27 28 30 28 34 34
B
6 6 8 10 10 10 12 10 12 12 15 15
Projecting tube U V R
15 15 19 19 22 23 27 28 30 28 34 34 15 15 18 20 21 22.5 27 27 29 31 37 37 7 5 7 7 8 8 8 10 12 10 17
Outside dia.
Arbor Bore do di
6.1 6.1 7.6 9.5 9.0 11.3 11.6 14.6 13.8 19.6 400 400 400 500 500 500 500 500 500 1000
8.1 8.1 9.6 11.5 11.0 13.3 13.6 17.0 16.2 22.0
0.75 17
19.0
16.6
1000
2000
2500
RS2510A**
3.13
Remarks 4. Nut assembly with arbor and the screw shaft are separated at time of delivery. 5. At the end of the screw shaft reference number where marked with "**", fill with the value obtained by dividing the standard screw shaft length by 100 mm. 6. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request.
Shaft diameter
Lead
Ball diameter
Root diameter
d
28
l
6
Dw
3.175
dm
28.5
dr
25.0
Static C oa
20300
0.10 2.5 x 2 40600 92200 51000 0.20 2.5 x 2 102000 164000 147000 205000 293000 0.20 0.23 0.20 0.23 60 65 70 80 85 0.20 50 55 60
32
10
6.35
33.75
27.0
2.5 x 2 2.5 x 1
36
10
6.35
37
30.0
40 45 50 50
10 12 10 16
Remarks 1. The protruding portion of the tube does not interfere with nut housing if its dimensions corresponding to U and V are large enough. 2. The actual screw shaft length may become slightly longer than nominal length Ls due to manufacturing tolerance. 3. Seals are provided in the nut. Therefore, the external dimensions of those with the seals are the same as those without. In the side view drawing of the nut, above the center line is with seal, and beneath is without seal. Seal is "Brush-seal".
Unit: mm
A
79 79 97 102 102 114 130 140 163
Flange G
33 33 39 42 42 44 47 52 57
B
15 15 18 18 18 20 22 22 28
Projecting tube U V R
33 33 39 42 42 44 47 52 57 34 34 42 46 46 50 55 59 63 10 10 17 17 17 20 20 20 25
Outside dia.
Arbor Bore do di
22.6 1000
25.0 1.07 1.55 1.47 30.0 1.80 2.49 3.07 4.06 6.42 35.0 39.0 45.0 42.0 27.0
24.6
1000
2000
3000
RS3210A**
5.53
27.6
1000
2000
3000
RS3610A**
6.91
Remarks 4. Nut assembly with arbor and the screw shaft are separated at time of delivery. 5. At the end of the screw shaft reference number where marked with "**", fill with the value obtained by dividing the standard screw shaft length by 100 mm. 6. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request.
Shaft diameter
Lead
Ball diameter
Root diameter
d
12 16 20 25 32 40
l
12 16 20 25 32 40
Dw
2.381 2.778 3.175 3.969 4.762 6.35
dm
12.65 16.65 20.75 26 33.25 41.75
dr
10.1 13.6 17.3 22.0 28.0 35.0
Static C oa
6270 9650 15400 24100 37100 61600
Remarks 1. Protruding portion of the tube does not have any interference with the ball nut housing if its dimensions corresponding to U and V are large enough. 2. The actual screw shaft length may become slightly longer than nominal length Ls due to manufacturing tolerance. 3. Seals are provided in the nut. Therefore, the external dimensions of those with the seals are the same as those without. In the side view drawing of the ball nut, above the center line is with seal, and beneath is without seal. Seals for ball nuts with the shaft diameter of 14 mm or less are made of synthetic resin. Seals for those of 16 mm or over are "Brush-seal."
Unit: mm
A
44 55 68 80 100 120
Flange G
17 22 25 31 37 46
B
8 10 12 12 15 18
Projecting tube U V R
17 22 25 31 37 46 16 22 27 32 40 49 5 7 8 10 12 15
Outside dia.
Arbor Bore do di
8.1 11.6 14.9 19.6 25.6 31.8 400 500 500 1000 1000 2000
Remarks 4. Nut assembly with arbor and the screw shaft are separated at time of delivery. 5. At the end of the screw shaft reference number where marked with "**", fill with the value obtained by dividing the standard screw shaft length by 100 mm. 6. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request.
Shaft diameter
Lead
Ball diameter
Root diameter
d
10 12 14 14 18 20 20 25 25 28 32 36 40
l
6 8 4 5 8 5 10 5 10 6 10 10 10
Dw
2.381 2.778 2.778 3.175 4.762 3.175 4.762 3.175 6.35 3.175 6.35 6.35 6.35
dm
10.65 12.65 14.5 14.5 18.5 20.5 21.25 25.5 26 28.5 33.75 37 41.75
dr
8.1 9.6 11.5 11.0 13.6 17.0 16.2 22.0 19.0 25.0 27.0 30.0 35.0
Static C oa
4810 6560 10800 9720 25800 14200 21800 18200 36300 35200 70300 20300 40600 46100 92200 51000 102000 116000
Remarks 1. The actual screw shaft length may be slightly longer than nominal length Ls due to manufacturing tolerance. 2. Nut assembly with arbor and screw shaft are separated at time of delivery. 3. The value obtained by dividing the standard screw length by 100 mm will be entered at the end of the reference number where marked with "* *".
10
Unit: mm
A
42 45 50 50 80 60 82 67 96 80 103 110 116
Flange H
29 32 37 38 60 46 64 50 72 60 78 82 88
B
8 8 10 10 12 10 12 10 15 12 15 17 17
Oil hole Q T
M3 x 0.5 M3 x 0.5 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 M6 x 1 5.0 5.5 5.0 5.0 6.0 5.0 6.0 5.0 7.5 6.0 7.5 8.5 8.5
Outside dia.
Arbor Bore do di
6.1 7.6 9.5 9.0 11.6 14.6 13.8 19.6 16.6 22.6 24.6 27.6 31.8 400 400 500 500 500 500 500
Screw shaft Shaft Standard length Screw shaft mass/m (kg) No. Ls
800 800 1000 1000 1000 1000 1000 2000 2000 2000 2000 2000 3000 1500 2000 2000 2500 2500 2500 3000 3000 4000 RS1006A** RS1208A** RS1404A** RS1405A** RS1808A** RS2005A** RS2010A** RS2505A** RS2510A** RS2806A** RS3210A** RS3610A** RS4010A** 0.56 0.81 1.02 1.00 1.60 2.17 2.18 3.47 3.13 4.47 5.53 6.91 8.87
8.1 9.6 11.5 11.0 13.6 17.0 16.2 22.0 19.0 25.0 27.0 30.0 35.0
Remarks 4. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request. 5. Seals for ball nuts with the shaft diameter of 14 mm or less are made of synthetic resin. Seals for those with 16 mm or larger are "Brush-seal."
11
Shaft diameter
Lead
Ball diameter
Root diameter
d
10 14 14 18 20 25 25 28 32 36 40 45 50 50
l
3 4 5 8 5 5 10 6 10 10 10 12 10 16
Dw
2.381 2.778 3.175 4.762 3.175 3.175 6.35 3.175 6.35 6.35 6.35 7.144 6.35 9.525
dm
10.65 14.5 14.5 18.5 20.5 25.5 26 28.5 33.75 37 41.75 46.5 51.75 52
dr
8.1 11.5 11.0 13.6 17.0 22.0 19.0 25.0 27.0 30.0 35.0 39.0 45.0 42.0
Static C oa
6730 10800 9720 25800 14200 36300 70300 40600 92200 102000 164000 147000 205000 293000
Remarks 1. Protruding portion of the tube does not have any interference with the ball nut housing if its dimensions corresponding to U and V are large enough. 2. The actual entire screw shaft length may become slightly longer than nominal length L s due to manufacturing tolerance. 3. A seal cannot be installed in the V thread side. It may be installed in the opposite side. Seal is provided in the nut. Therefore, the external dimensions of those with a seal are the same as those without. In the side view drawing of ball nut, above the center line is with seal, and beneath is without seal. Seals for ball nuts with the shaft diameter of 14 mm or less are made of synthetic resin. Seals for those of 16 mm or over are "Brush-seals." There is no seal on the V-thread side for RNCT1404A3.5S and RNCT1405A2.5S.
12
Unit: mm
Outside dia.
Arbor Bore do di
6.1 9.5 9.0 11.6 14.6 19.6 16.6 22.6 24.6 27.6 31.8 35.8 41.8 38.8
8.1 11.5 11.0 13.6 17.0 22.0 19.0 25.0 27.0 30.0 35.0 39.0 45.0 42.0
4. Nut assembly with arbor and the screw shaft are separated at time of delivery. 5. At the end of the screw shaft reference number where marked with "**", fill with the value obtained by dividing the standard screw shaft length by 100 mm. 6. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request.
13
Shaft diameter
Lead
Ball diameter
Root diameter
d
14 14 18 20 20 25 25 28 32 36 45
l
4 5 8 5 10 5 10 6 10 10 12
Dw
2.778 3.175 4.762 3.175 4.762 3.175 6.35 3.175 6.35 6.35 7.144
dm
14.5 14.5 18.5 20.5 21.25 25.5 26 28.5 33.75 37 46.5
dr
11.5 11.0 13.6 17.0 16.2 22.0 19.0 25.0 27.0 30.0 39.0
Static C oa
10800 9720 25800 14200 21800 18200 70300 20300 40600 46100 92200 51000 102000 147000
Remarks 1. The actual screw shaft length may be slightly longer than nominal length Ls due to manufacturing tolerance. 2. Nut assembly with arbor and screw shaft are separated at time of delivery. 3. The value obtained by dividing the standard screw length by 100 mm will be entered at the end of the reference number where marked with "* *".
14
Unit: mm
Width W
34 34 48 48 48 60 60 60 60 70 70 86 86 100
Center height
H
13 13 17 17 18 20 23 22 22 26 26 29 29 36
A
22 22 35 22 35 22 60 18 40 45 60 45 60 75
E
7 7 8 6 10 6 10 8 10 11 13
Oil hole F
3 3 3 2 2 0 0 0 0 0 0
U
20 21 26 27 28 27 32 32 38 41 46
Outside dia.
Arbor Bore do di
9.5 9.0 11.6 14.6 13.8 19.6 16.6 22.6 24.6 27.6 35.8 500 500 500 500 500 1000 1000 1000 1000 1000 2000
11.5 11.0 13.6 17.0 16.2 22.0 19.0 25.0 27.0 30.0 39.0
Remarks 4. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request. 5. Seals for ball nuts with the shaft diameter of 14 mm or less are made of synthetic resin. Seals for those with 18 mm or larger are "Brush-seals."
15
Shaft diameter
Lead
Ball diameter
Root diameter
d
12 15
l
12 20
Dw
2.381 3.175
dm
12.65 15.5
dr
10.1 12.2
Static C oa
6640 13300 12300 10400
16
16
2.778
16.65
0.10
32
20
20
3.175
20.75
0.10
39
25
25
3.969
26
0.12
47
32
32
4.762
33.25
0.15
58
40
40
6.35
41.75
0.20
73
50
50
7.938
52.25
0.25
90
Remarks 1. The actual screw shaft length may be slightly longer than nominal length Ls due to manufacturing tolerance. 2. Nut assembly with arbor and screw shaft are separated at time of delivery. 3. The value obtained by dividing the standard screw length by 100 mm will be entered at the end of the reference number where marked with "* *".
16
Unit: mm
Flange A H B
44 51 28 35 6 10
Oil hole Q T
M3 x 0.5 M6 x 1 3.0 5.0
Arbor
Outside dia.
do
10.1 12.2
Bore di
8.1 10.2 400 500
53
34
10
10
38
42
4.5
M6 x 1
5.0
0.23
13.5
11.5
500
1000
1500
RS1616A**
1.37
62
41
10
11.5
46
50
5.5
M6 x 1
5.0
0.37
17.3
14.9
500
1000
2000
RS2020A**
2.19
74
49
12
13
55
60
6.6
M6 x 1
6.0
0.62
22.0
19.6
1000
2000
2500
RS2525A**
3.43
92
60
12
16
70
74
M6 x 1
5.5
1.10
28.0
25.6
1000
2000
3000
RS3232A**
5.71
114
75
15
19.5
85
93
11
M6 x 1
6.5
2.09
35.0
31.8
2000
3000
4000
RS4040A**
8.82
135
92
20
21.5
107
112
14
M6 x 1
7.0
3.90
44.0
40.8
2000
3000
4000
RS5050A**
13.81
Remarks 4. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request. 5. The entire length of the nut becomes longer by "2 x M " for those with a seal. The seal is "Brush-seal."
17
Shaft diameter
Lead
Ball diameter
Root diameter
Dw
dm
dr
Static C oa
8460 10400 20800 13600 16500 33000 21200 25800 51500 40500
16
32
2.778
16.65
13.5
0.10
32
20
40
3.175
20.75
17.3
0.10
38
25
50
3.969
26
22.0
0.12
46
32
64
4.762
33.25
0.15
58
40
80
6.350
41.75
0.20
73
Remarks 1. The actual screw shaft length may be slightly longer than nominal length Ls due to manufacturing tolerance. 2. Nut assembly with arbor and screw shaft are separated at time of delivery. 3. The value obtained by dividing the standard screw length by 100 mm will be entered at the end of the reference number where marked with "* *".
18
Unit: mm
Flange A H B
Oil hole Q T
Arbor
Outside dia.
do
Bore di
50
34
10
10
66 66 41
41
4.5
M6 x 1
5.5
13.5
11.5
500
1000
1500
RS1632A**
1.34
58
40
10
11
81 81 50
48
5.5
M6 x 1
5.5
17.3
14.9
500
1000
1500
2000
RS2040A**
2.15
70
48
12
13
100 100
58
6.6
M6 x 1
7.0
0.91 0.91
22.0
19.6
1000
2000
2500
RS2550A**
3.37
92
60
12
15.5
126
74
M6 x 1
7.5
1.76
28.0
25.6
1000
2000
3000
4000
RS3264A**
5.63
114
75
15
19
158
93
11
M6 x 1
10
3.44
35.0
31.8
2000
3000
4000
5000
RS4080A**
8.69
Remarks 4. Items in stock are not provided with any special surface treatment. NSK provides treatment such as phosphate coating on request. 5. The entire length of the nut becomes longer by "2 x M " for those with a seal. The seal is "Brush-seal."
19
Table 3 Dimensions of rolled screw shaft ends (drive side) Bearing journal Screw shaft Outside Length diameter diameter d1 L1 d
10 12 14 15 16 18 20 25 28 32 36 40 45 50 6 8 10 10 12 12 15 20 20 25 25 30 35 35 27 32 35 35 35 35 50 64 64 76 76 89 92 92
Unit: mm
Thread for lock nut Spacer* Nominal Length Width spec m1 mL1 E
M6x0.75 M8x1 M10x1 M10x1 M12x1 M12x1 M15x1 M20x1 M20x1 M25x1.5 M25x1.5 M30x1.5 M35x1.5 M35x1.5 7 9 10 10 10 10 15 16 16 20 20 26 30 30 5.0 5.5 5.5 5.5 5.5 5.5 10 11 11 14 14
Hexagonal hole Wrench flat Width Depth Width Length across flats across flats B h H S
4 4 5 6 6 8 8 10 12 12 6 6 7 8 8 10 10 12 14 14 8 10 12 12 12 12 17 22 22 27 27 4.5 5.5 6.5 6.5 6.5 6.5 8.5 10 10 12 12
Note : The dimension d1 shall be smaller enough than the minor diameter of the ball screw thread to provide sufficient shoulder surface for the spacer. * For spacer information please refer to page 31.
20
Figure 2 Shaft end configuration of rolled ball screw (opposite to the drive side)
Table 4 Dimensions of rolled ball screw shaft end (opposite to the drive side) Screw shaft diameter d
10 12 14 15 16 18 20 25 28 32 36 40 45 50
Unit: mm
Width
n
0.8 0.9 1.15 1.15 1.15 1.15 1.15 1.35 1.35 1.35 1.35 1.75 1.75 1.75
Groove position nL
6.8 7.9 9.15 9.15 9.15 9.15 10.15 15.35 15.35 16.35 16.35 17.75 18.75 18.75
21
6~25
26
Square
WBK**S-01
6~25
28
Round
WBK**-11
6~25
30
Round
WBK**DF*-31
17~40
32
Features
Short delivery time: Standardized items in stock. Use most suitable bearings. On the fixed support side, the angular contact ball bearing is used. It has great rigidity and low friction torque which match the rigidity of the ball screw. The thrust angular contact ball bearing with high precision and great rigidity is another choice for the fixed support side.
High dust prevention, and low friction torque. Oil seal is installed in small clearance on the fixed support side. A deep-groove ball bearing with a shield on both sides is used on the simple support side. This minimizes friction torque. Lock nut is provided. A lock nut of fine grade finish is provided to fix the bearing with high precision.
22
Example:
Product code for support unit Nominal size code* Mounting code No code: Fixed support unit S: Simple support unit
WBK 08 S - 01 A
No code or A: For general use 01: Square type 11: Round type
* In case of simple support unit, be careful that 12 or less size codes do not represent internal bores of bearing. Please refer to the dimensional table for internal bore of bearing (Page 29).
Example:
Product code for support unit
WB/BK 25 DF - 31
Design serial number
Nominal size code (internal bore of bearing) Bearing combination code DF : Face to face duplex combination DFD : Face to face triplex combination DFF : Face to face quadruplex combination
23
Support units provide everything necessary for mounting ball screws to machines. (Please refer to Table 6.) * Do not disassemble fixed support side units as they are equipped with bearings and oil seals.
Antirust treatment Table 7 shows the surface treatment for the bearing housing and material of small parts.
Table 6
Fixed support side Part no. Name of part
Bearing housing Spacer Locknut Set screw with set piece
Table 7
General support unit
Bearings and grease Surface treatment Screws and snap rings Angular contact ball bearings, PS2 Black oxide Standard material
24
Table 8 Specifications of support unit for general use Fixed support side support unit Axial direction Basic dynamic Load limit Stiffness load rating Ca [N] [N] [N/m]
2 670 4 400 6 600 7 100 7 600 17 900 20 200 1 040 1 450 2 730 3 040 3 380 8 240 10 000 28 49 94 104 113 155 192
Reference no.
WBK06-01A WBK06-11 WBK08-01A WBK08-11 WBK10-01A WBK10-11 WBK12-01A WBK12-11 WBK15-01A WBK15-11 WBK20-01 WBK20-11 WBK25-01 WBK25-11 (SQUARE) (ROUND) (SQUARE) (ROUND) (SQUARE) (ROUND) (SQUARE) (ROUND) (SQUARE) (ROUND) (SQUARE) (ROUND) (SQUARE) (ROUND)
Simple support side support unit Bearing Radial direction Reference no. reference no. Basic dynamic load rating C [N]
WBK08S-01 (SQUARE) WBK10S-01 (SQUARE) WBK12S-01 (SQUARE) WBK15S-01 (SQUARE) WBK20S-01 (SQUARE) WBK25S-01 (SQUARE) 606ZZ 608ZZ 6000ZZ 6002ZZ 6204ZZ 6205ZZ 2 260 3 300 4 550 5 600 12 800 14 000
25
Support Unit
(Support units for light load and small equipment) Fixed support side, support unit (square type)
d1
6 8 10 12 15 20 25
A
42 52 70 70 80 95 105
B
25 32 43 43 50 58 68
E
18 25 36 36 41 56 66
F
12 14 17 19 22 30 36
J
20 23 30 30 31 52 61
1. Use datum face A to mount a machine base. 2. Tighten a set screw after a locknut is adjusted and tightened. 3. Insert the set piece that is provided with support unit to a screw hole, and then tighten the set screw.
26
Reference no.
WBK06-** WBK08-** WBK10-** WBK12-** WBK15-** WBK20-** WBK25-**
Unit: mm
K
5.5 7 5.5 5.5 12 10 13
L
24 24 25 42 48
N
3.5 4 6 6 5 10 14
X
5.5 6.6 9 9 11 11 11
M
M6 x 0.75 M8 x 1 M10 x 1 M12 x 1 M15 x 1 M20 x 1 M25 x 1.5
27
Support Unit
(Support units for light load and small equipment) Simple support side, support unit (square type)
d2
6 8 10 15 20 25
B
32 43 43 50 58 68
28
Unit: mm
C
17 25 25 30 30 35
D
26 35 35 40 45 25
E
25 36 36 41 56 66
Y
11 14 14 14 17 No counter bores
Z
12 11 11 11 15
29
Support Unit
(Support units for light load and small equipment) Fixed support side, support unit (round type)
d1
6 8 10 12 15 20 25
A
28 35 42 44 52 68 79
C
35 43 52 54 63 85 98
H
13 14 17 17 17 30 30
J
7 9 10 10 15 22 27
K
3.5 4 5 5 6 10 10
1. Tighten a set screw after a locknut is adjusted and tightened. 2. Insert the set piece that is provided with support unit to a screw hole, and then tighten the set screw.
30
Reference no.
WBK06-** WBK08-** WBK10-** WBK12-** WBK15-** WBK20-** WBK25-**
Unit: mm
L
9.5 10 12 12 11 20 20
N
6.5 8 8.5 8.5 14 14 20
P
4.5 5 6 6 8 14 17
X
2.9 3.4 4.5 4.5 5.5 6.6 9
Y
5.5 6.5 8 8 9.5 11 15
Z
3.5 4 4 4 6 10 13
M
M6 x 0.75 M8 x 1 M10 x 1 M12 x 1 M15 x 1 M20 x 1 M25 x 1.5
Spacer It requires an optional spacer to the side where ball thread is cut through, such as a rolled ball screw shaft when mounting the support unit for fixed support side.
Unit: mm
Reference no.
WBK06K WBK08K WBK10K WBK12K WBK15K WBK20K WBK25K
Note:
Internal diameter, d
6 8 10 12 15 20 25
Outside diameter, D
9.5 11.5 14.5 15.0 19.5 25.5 32.0
Width B
5.0 5.5 5.5 5.6 10.0 11.0 14.0
31
DF combination
DFD combination
DFF combination
32
Remarks
1. Mount sections A and B to the machine base. 2. NSK support units are precisely preloaded and adjusted. Components , , , , and are assembled into a unit. Do not disassemble. 3. Grease is packed into the bearings. 4. Lock nut is exclusively prepared for ball screw. The end face of the nut is in strict control being precisely perpendicular to the V thread. Secure the lock nut using the set screw.
Quantity
1 1 One set 2 2 6 or 8 One set 1
33
Support Unit
For heavy load applications
d
17 20 25 30
D
70 70 85 85
D1
106 106 130 130
D2
72 72 90 90
L
60 60 66 81 66 81 66 81 96 66 81 96
L1
32 32 33 48 33 48 33 48 48 33 48 48
L2
15 15 18 18
Support unit A W X
80 80 100 100 88 88 110 110 9 9 11 11
Y
14 14 17.5 17.5
Z
8.5 8.5 11 11
d 1*
45 45 57 57
l*
3 3 4 4
V*
58 58 70 70
P*
M5 M5 M6 M6
Q*
10 10 12 12
35
95
142
102
18
106
121
11
17.5
11
69
80
M6
12
40
95
142
102
18
106
121
11
17.5
11
69
80
M6
12
Remarks 1. Rigidity Values in the Table are theoretical values obtained from the elastic deformation between the groove and the balls. 2. Starting torque Starting torque indicates torque due to the preload of the bearing. It does not include seal torque. 3. The tolerance of the shaft bearing seat We recommend h5 class of the fits tolerance.
34
Unit: mm
Preload (N)
2150 2150 3150 4300 3350 4500 3800 5200 7650 3900 5300 7850
M
M17 x 1 M20 x 1 M25 x 1.5 M30 x 1.5
Lock nut D3
37 40 45 50
L3
18 18 20 20
Mass (kg)
1.9 1.9 3.1 3.4 3.0 3.3 3.4 4.3 5.0 3.6 4.2 4.7
M35 x 1.5
55
22
35
30
M40 x 1.5
60
22
40
30
Remarks 4. Dimensions with * (asterisk) *Pilot diameter and tapped screws marked with "*" are used for seal unit installation for NSK standard hollow shaft ball screws. They also can be used for dust cover and damper installation. 5. Grease is packed into the bearing. It is not necessary to apply grease before use.
35
Figure 4
When delivered, the nut of rolled ball screw is separated from the screw shaft and inserted into an arbor shaft.
36
Installation
(1) Centering of the units
Align the centers of housings for the ball nut and the support bearing to which a ball screw is fixed. The centering is critical for life, smooth operation, and positioning accuracy of a ball screw. We generally recommend the centering accuracy as follows for a precision grade ball screw. Inclination of center line: 1/2,000 or less (Target: 1/5,000 or less) Eccentricity: 0.020 mm or less Follow the flowchart in Figure 5 for installation procedures.
Figure 5
Bearing housing
Photo 2
Trial running
Lubrication
Centering
37
Table
Photo 3
Photo 4
Photo 5
38
Machine base
Photo 9
39
Lubrication
There are two types of lubricating methods grease and oil for ball screws and linear guides. Use a lubricant agent and method most suitable to condition requirements and purpose to optimize functions of the ball screws and linear guides. In general, lubricants with low base oil kinematic viscosity are used for high speed operation. Lubrication with high base oil kinematic viscosity is used for oscillating operations, low speed and high temperature. The following are lubrication methods by grease and by oil.
Grease Lubrication
Grease lubrication is widely used because it does not require special oil supply system or piping. Grease lubricants made by NSK are: Various types of grease in bellowed container which can be instantly attached to the grease pump; NSK Grease Unit which comprises a hand grease pump and various nozzles. The units are compact and easy to use. NSK grease lubricants Table 9 shows the marketed general grease widely used for linear guides and ball screws for various applications, conditions and purposes.
Table 9 Grease lubricant for linear guides and ball screws Type
AS2
Thickener
Lithium type
Base oil
Mineral oil
Purpose
For ball screws and linear guides for general use at high load. For ball screws and linear guides for low temperature and high frequency operation. For ball screws at high speed, medium load. For ball screws and linear guides for clean environment. For ball screws and linear guides for clean environment. For fretting resistant ball screws and linear guides.
PS2
Lithium type
15
50~110
LR3
Lithium type
30
30~130
LG2
Lithium type
30
10~80
LGU
Diurea
100
30~120
NF2
Synthetic oil
27
40~100
Items to check
Dirt, foreign matters such as cutting chip
Intervals of replenishment
Usually once per year. Every 3000 km for material handling system which travels more than 3000 km per year. Replenish if checking results warrant it.
40
Other Products
Precision Ball Screws Available with clearance and preload type, blank and finished shaft ends, and optional K1 Lubrication Unit for maintenance-free operation. Rolled Precision Ball Screws High lead, zero backlash, finished shaft ends, and optional K1 Lubrication Unit for maintenance-free operation. Linear Guides Also called profile rails, NSK manufactures various types with sizes ranging from 7mm to 65mm. Linear Bushings Inch and metric linear bushings and 60 case shafting. Monocarriers Integrating linear guides and a ball screw, Monocarriers are a compact precision actuator. Megatorque Motor Precision indexing, repeatability and high torque.
Unit Conversions
To convert
From
daN kgf kgf kgf.cm kgf.cm kgf.m kgf.m N.m mm inch
For more information, visit
To
N N lbf lbf.in ozf.in lbf.ft lbf.in lbf.ft inch mm
Multiply By
10.000 9.81 2.205 0.868 13.890 7.234 86.811 0.738 0.03937 25.4
www.tec.nsk.com www.npa.nsk.com
41
42
43
44
Africa
Australia: www.nskaustralia.com.au NSK Australia Pty. Ltd. Melbourne tel: (03) 9764-8302 China: NSK Hong Kong Ltd. Hong Kong tel: 2739-9933 Kunshan NSK Co., Ltd. Kunshan tel: 0520-7305654 Guizhou HS NSK Bearings Co., Ltd. Anshun tel: 0853-3521505 NSK (Shanghai) Trading Co., Ltd. Shanghai tel: 021-62099051 NSK representative office Beijing tel: 010-6590-8161 NSK representative office Shanghai tel: 21-6209-9051 NSK representative office Guangzhou tel: 020-8732-0583 NSK representative office Anshun tel: 0853-3522522 India: Rane NASTECH Ltd. Chennai tel: 04114-65313, 65314, 65365, 66002 NSK representative office Chennai tel: 044-4334732 Indonesia: P NSK Bearings Manufacturing Indonesia .T. Jakarta tel: 021-898-0155 Korea: NSK Korea Co., Ltd. Seoul tel: 02-3287-0300 NSK Korea Co., Ltd., Changwon Plant Changwon tel: 0551-287-6001 Malaysia: NSK Bearings (Malaysia) Sdn. Bhd. Kuala Lumpur tel: 03-7958-4396 NSK Micro Precision (M) Sdn. Bhd. Kuala Lumpur tel: 03-961-6288 New Zealand: www.nsk-rhp.co.nz NSK New Zealand Ltd. Auckland tel: (09) 276-4992
Europe
NSK Europe Ltd. (European Headquarters) www.eu.nsk.com Maidenhead, England tel: 0162-850-9800 France: NSK France S.A. Paris tel: 01 30 57 39 39 Germany: NSK Deutschland Gmbh Dsseldorf tel: 02102-481-0 NSK Steering Systems Europe Ltd. Stuttgart tel: 0771-79082-277 Neuweg Fertigung Gmbh Munderkingen tel: 07393-540 Italy: NSK Italia S.P.A. Milano tel: 02-995-191 Poland: NSK Europe Ltd. Warsaw Liaison Office Warsaw tel: 48-22-645-1525, 1526 NSK Iskra S.A. Kielce tel: 48-41-366-6111 Spain: NSK Spain S.A. Barcelona tel: 93-575-4041
NSK Ltd. has a basic policy not to export any products or technology designated as controlled items by export-related laws. When exporting the products in this brochure, the laws of the exporting country must be observed. Specifications are subject to change without notice and without any obligation on the part of the manufacturer. Every care has been taken to ensure the accuracy of the data contained in this brochure, but no liability can be accepted for any loss or damage suffered through errors or omissions. We will gratefully acknowledge any additions or corrections.
CAT BALL SCREWS 05 Printed in Canada NSK 2005. The contents of this publication are the copyright of the publishers.