Sei sulla pagina 1di 19

"BEAMTAB" --- BEAM END CONNECTION USING BEAM TAB (SINGLE PLATE)

Program Description:
"BEAMTAB" is a spreadsheet program written in MS-Excel for the purpose of analysis of steel beam end connections using a beam tab (single plate) field bolted to the beam web and shop welded to either the column flange, column web, or girder web. The connections may be subjected to end shear reaction and/or axial load. Specifically, all applicable "limit states" for the end connection analysis pertaining to the beam tab (single plate), bolts, beam web, and either column flange or web, or girder web are checked. This program is a workbook consisting of four (4) worksheets, described as follows:

Worksheet Name
Doc Beam Tab(Col Flg) Beam Tab(Col Web) Beam Tab(Girder)

Description
This documentation sheet Beam tab bolted to beam web and welded to column flange Beam tab bolted to beam web and welded to column web Beam tab bolted to beam web and welded to girder web

Program Assumptions and Limitations:


1. This program follows the procedures and guidelines of the AISC 9th Edition Allowable Stress (ASD) Manual (1989) and the AISC 9th Edition Manual Vol. II - Connections (1992). 2. This program uses the database of member dimensions and section properties from the "AISC Shapes Database", Version 3.0 (2001) as well as the AISC 9th Edition (ASD) Manual (1989). 3. This program automatically calculates the beam tab height, 'Hp', and the beam tab width, 'Wp', based on the applicable input data. 4. This program assumes that the a beam tab connected (welded) to a column flange is a rigid connection, while a beam tab connected (welded) to a column web or girder web is a flexible connection. The applicable connection design eccentricity, based on either a rigid or flexible connection, is determined from the criteria in the AISC Connections Manual. 5. This program assumes that the tension capacity for any "limit state" is reduced by the presence of shear. For allowable bolt tension in the presence of shear, the "interaction" (combined stresses) is handled directly by the AISC Code equations. For other "limit states" in combined stresses such as bolt bearing, gross and net shear and tension, and block shear and tension tearout, the effect of "interaction" is handled by use of the formula, P/Ra+(R/Rv)^2=1, as suggested from the following reference: "Combined Shear and Tension Stress" - by Subhash C. Goel, AISC Journal, 3rd Qtr.-1986. Thus, the reduction factor applied to the tension "limit state" capacity is = (1-R/Rv)^2. where: R = actual shear end reaction Rv = allowable shear capacity for the particular "limit state" considered 6. This program contains numerous comment boxes which contain a wide variety of information including explanations of input or output items, equations used, data tables, etc. (Note: presence of a comment box is denoted by a red triangle in the upper right-hand corner of a cell. Merely move the mouse pointer to the desired cell to view the contents of that particular "comment box".)

"BEAMTAB.xls" Program Version 1.3

AISC BEAM END CONNECTION (ASD)


Using Beam Tab (Single Plate) Bolted to Beam Web and Welded to Column Flange Subjected to Shear and/or Axial Load Job Name: Subject: Job Number: Originator: Checker: Input Data: Beam and Column Data: Beam Size = Column Size = Beam Yield Stress, Fyb = Column Yield Stress, Fyc = Connection Loading: Beam End Reaction (Shear), R = Beam Axial Force, P =
tf=0.72

W16x26 W14x68 50 50

d=14
ksi ksi

Face of Col. Flange tp=0.375 ED1=1.5 Hp=9 S1=3 S1=3

16.00 0.00

kips kips

ED2=1.5 S2=0 D2=3 D1=3 P=0 k R= 16 k s=0.5 Wp=4.5

Connection Data and Parameters: Beam Tab Height, Hp = 9.0000 Beam Tab Width, Wp = 4.5000 Beam Tab Thickness, tp = 0.3750 Beam Tab Yield Stress, Fyp = 36 Diameter of Bolts, db = 0.750 ASTM Bolt Desig. (A325 or A490) = A325 Bolt Type (N, X, or SC) = N Bolt Hole Type in Beam Tab = Short-Slot Total No. of Bolts in Beam Tab, Nb = 3 Number of Vertical Rows, Nr = 1 Dist. from Top/Beam to Bolts, D1 = 3.0000 Bolt Vertical Spacing, S1 = 3.0000 Vertical Edge Distance, ED1 = 1.5000 Dist. to 1st Row of Bolts, D2 = 3.0000 Bolt Horizontal Spacing, S2 = 0.0000 Horizontal Edge Distance, ED2 = 1.5000 Beam Setback Distance, s = 0.5000 Length of Flange Cope(s), c = 0.0000 Depth of Top Flange Cope, dc1 = 0.0000 Depth of Bottom Flange Cope, dc2 = 0.0000 Fillet Weld Size at Beam Tab, w = 5/16 Member Properties: Beam: A= 7.68 d = 15.700 tw = 0.250 bf = 5.500 tf = 0.345 k = 0.7470

in. in. in. ksi in.

5/16 5/16

General Nomenclature
tw=0.25 tf=0.345 c=0 dc1=0

in. in. in. in. in. in. in. in. in. in. in.

d=15.7

bf=5.5 c=0

dc2=0

Beam and Cope Nomenclature

Max. Shear Capacity of Connection: R(max) = 24.26 kips A= d= tw = bf = tf = k= Column: 20.00 14.000 0.415 10.000 0.720 1.3100
in.^2 in. in. in. in. in. (continued)

2 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Results: General Parameters: Bolt and Material Data: dhy1 = 0.9375 dhx1 = 1.0000 dh2 = 0.8125 Ab = 0.4418 Fup = 58.0 Fub = 65.0 Fuc = 65.0

in. in. in. in.^2 ksi ksi ksi

dhy1 = db+3/16 (Short-Slot hole for 0.75 in. bolts in plate) dhx1 = db+1/4 (Short-Slot hole for 0.75 in. bolts in plate) dh2 = db+1/16 (Standard hole for 0.75 in. bolts in beam web) Ab = p*db^2/4 Fup = 58 for Fyp = 36 (for plate) Fub = 65 for Fyb = 50 (for beam) Fuc = 65 for Fyc = 50 (for column) (assuming "rigid" support provided at column flange) (using AISC Table XI, page 4-62) n = Nb/Nr (number of bolts in a vertical row) b = S1 eb = ABS(2*(Nb/Nr)/3-D2) (interpolated from Table XI) Pr = SQRT(R^2+P^2) (total resultant load taken by bolts) q = 90-(ATAN(R/P)) (angle from vertical) Co = "C" coefficient from AISC Table XI C(max) = n A = C(max)/Co >= 1.0 Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = (Ca/Co)*Co vb = Pr/(C or Ca) fv = vb/Ab Fv = Allow. shear stress from AISC Table J3.2, page 5-73 (for N bolts) Vb = Fv*Ab Rbr = Vb*(C or Ca) (resultant) Rbv = Rbr*COSq (vertical) Rbv >= R, O.K. Rba = Rbr*SINq (axial)

Beam Tab to Beam Connection: Bolt Shear (includes eccentricity): n= 3 bolts b= 3.000 in. eb = 1.000 in. C= 2.615 Pr = 16.00 kips q = 0.000 deg. Co = N.A. C(max) = N.A. A= N.A. Ca/Co = N.A. Ca = N.A. vb = 6.12 kips/bolt fv = 13.85 ksi Fv = 21.00 ksi Vb = 9.28 kips/bolt Rbr = 24.26 kips Rbv = 24.26 kips Rba = 0.00 kips

Beam Tab Checks: Bolt Bearing Capacity of Plate (for Vertical): C1 = 0 in. C1 = Spacing increment from AISC Table J3.4, page 5-76 C2 = 0 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 19.58 kips Rpe = (1.2*Fup*db*tp)*(Nr) (C2 is not applicable for ED1 >= 1.5*db) Rps = 39.15 kips Rps = (1.2*Fup*db*tp)*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 58.73 kips Rpv = Rpe+Rps <= (1.2*Fup*db*tp)*Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Plate (for Axial): C1 = N.A. in. C1 = Spacing increment (not applicable for all edge bolts) C2 = 0.13 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 58.73 kips Rpe = (1.2*Fup*db*tp)*(Nb/Nr) (C2 is not applicable for ED2 >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load Rpa = 54.37 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= (1.2*Fup*db*tp)*(Nb)*(1-(R/Rpv)^2)
(Ref.: "Comb. Shear & Tension Stress" by: S.C. Goel, AISC Journal, 3rd Qtr.-1986) (continued)

3 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Gross Shear Capacity of Plate: Avg = 3.375 in.^2 Rvg = 48.60 kips Net Shear Capacity of Plate: Avn = 2.320 ksi Rvn = 40.37 kips Gross Tension Capacity of Plate: Atg = 3.375 in.^2 Rtg = 65.00 kips Net Tension Capacity of Plate: Atn = 2.250 in.^2 Rtn = 55.00 kips

Avg = Hp*tp Rvg = 0.40*Fyp*Avg

Rvg >= R, O.K.

Avn = (Hp-(Nb/Nr)*dhy1)*tp Rvn = 0.30*Fup*Avn

Rvn >= R, O.K.

Atg = Hp*tp Rtg = (0.60*Fyp*Atg)*(1-(R/Rvg)^2)

Atn = Atg-(Nb/Nr*(dhy1+1/16)*tp) <= 0.85*Atg Rtn = (0.50*Fup*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyp*Atg)*(1-(R/Rvn)^2)

Block Shear ("L-shaped") Capacity of Plate: Av = 1.934 in.^2 Av = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp At = 0.375 in.^2 At = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp Rbs = 44.52 kips Rbs = 0.30*Fup*Av+0.50*Fup*At Rbs >= R, O.K. Tension Tear-Out ("L-shaped") Capacity of Plate: Av = 0.375 in.^2 Av = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.934 in.^2 At = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp Rto = 54.51 kips Rto = (0.30*Fup*Av+0.50*Fup*At)*(1-(R/Rbs)^2) Tension Tear-Out ("U-shaped") Capacity of Plate: Av = 0.750 in.^2 Av = 2*(ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.547 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dhy1)*tp Rto = 57.91 kips Rto = (0.30*Fup*Av+0.50*Fup*At) Gross Bending in Plate: e= 4.000 in. M= 64.00 in.-kips Sg = 5.06 in.^3 fbg = 12.64 ksi Fbg = 21.60 ksi Rbg = 27.34 kips Net Bending in Plate: e= 1.000 M= 16.00 Sn = 3.56 fbn = 4.49 Fbn = 21.60 Rbn = 76.95

e = D2+eb (eccentricity for plate bending at support) M = R*e (eccentric moment at face of support) Sg = tp*Hp^2/6 fbg = M/Sg Fbg = 0.60*Fyp Rbg = (Fbg*Sg/e)*(1-(P/Rtg)) Rbg >= R, O.K.

in. in.-kips in.^3 ksi ksi kips

e = eb (eccentricity for plate bending at holes) M = R*e (eccentric moment at face of support) Sn = tp*Hp^2/6-S1^2*(Nb/Nr)*((Nb/Nr)^2-1)*(tp*(dhy1+1/16))/(6*Hp) fbn = M/Sn Fbn = 0.60*Fyp Rbn = (Fbn*Sn/e)*(1-(P/Rtn)) Rbn >= R, O.K.
(continued)

4 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Axial Compression Capacity of Plate: Acg = 3.38 in.^2 Acg = Hp*tp Lc = 3.00 in. Lc = Max. of D2 or S2 K= 1.20 (assumed effective length factor for plate supported on one edge) r= 0.108 in. r = tp/(SQRT(12)) KL/r = 33.26 KL/r = K*Lc/r Cc = 126.10 Cc = SQRT(2*p^2*29000/Fyp) Fa = 19.71 ksi If KL/r <= Cc: Fa = --(1-(K*Lc/r )^2/(2*Cc^2))*Fyp/(5/3+3*(K*Lc/r)/(8*Cc)-(K*Lc/r)^3/(8*Cc^3)) --If K*L/r > Cc: Fa = 12*p^2*29000/(23*(K*Lc/r)^2) Rc = 66.51 kips Rc = Fa*Acg Beam Checks for Uncoped Flanges: Bolt Bearing Capacity of Beam Web (for Vertical): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = N.A. in. C2 = Edge distance increment (not applicable for uncoped beam) Rpe = 14.63 kips Rpe = 1.2*Fub*db*tw*(Nr) (for Nr edge bolts, edge dist., C2 are N.A.) Rps = 29.25 kips Rps = 1.2*Fub*db*tw*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 43.88 kips Rpv = Rpe+Rps <= 1.2*Fub*db*tw*(Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Beam Web (for Axial): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = 0 in. C2 = Edge distance increment (C2 = 0 for Standard holes in web) Rpe = 43.88 kips Rpe = 1.2*Fub*db*tw*(Nb/Nr) (C2 is not applicable for D2-s >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load) Rpa = 38.04 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= 1.2*Fub*db*tw*(Nb)*(1-(R/Rpv)^2) Gross Shear Capacity of Beam Web: ho = N.A in. ho = not applicable for uncoped beam Avg = 3.925 in.^2 Avg = d*tw Rvg = 78.50 kips Rvg = 0.40*Fyb*Avg Net Shear Capacity of Beam Web: Avn = 3.316 in.^2 Rvn = 64.65 kips Gross Tension Capacity of Beam: Atg = 7.680 in.^2 Rtg = 220.83 kips Net Tension Capacity of Beam: Atn = 6.528 in.^2 Rtn = 199.17 kips

Rvg >= R, O.K.

Avn = (d-Nb/Nr*dh2)*tw Rvn = 0.30*Fub*Avn <= 0.40*Fyb*Avg

Rvn >= R, O.K.

Atg = A Rtg = (0.60*Fyb*Atg)*(1-(R/Rvg)^2)

Atn = Atg-(Nb/Nr*(dh2+1/16))*tw <= 0.85*Atg Rtn = (0.50*Fub*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyb*Atg)*(1-(R/Rvn)^2)

(continued)

5 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Checks for Uncoped Flanges (continued): Block Shear ("L-shaped") Capacity of Beam Web: Av = N.A. in.^2 Av = not applicable for uncoped beam At = N.A. in.^2 At = not applicable for uncoped beam Rbs = N.A. kips Rbs = not applicable for uncoped beam Tension Tear-Out ("L-shaped") Capacity of Beam Web: Av = N.A. in.^2 Av = not applicable for uncoped beam At = N.A. in.^2 At = not applicable for uncoped beam Rto = N.A. kips Rto = not applicable for uncoped beam Tension Tear-Out ("U-shaped") Capacity of Beam Web: Av = 1.047 in.^2 Av = 2*((D2-s)+(Nr-1)*S2-((Nr-1)*dh2+dh2/2))*tw At = 1.094 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dh2)*tw Rto = 55.96 kips Rto = 0.30*Fub*Av+0.50*Fub*At Web Buckling (Flexure) Capacity Not Applicable for Uncoped Beam ho = N.A. in. ho = d-dc1 e= N.A. in. e = c+s yc = N.A. in. yc = (bf*tf^2/2+(ho-tf)*tw*(tf+(ho-tf)/2))/((ho-tf)*tw+bf*tf) In = N.A. in.^4 In=bf*tf^3/12+bf*tf*(yc-tf/2)^2+tw*(ho-tf)^3/12+(ho-tf)*tw*(tf+(ho-tf)/2-yc)^2 Sn = N.A. in.^3 Sn = In/(ho-yc) c/ho = N.A. c/ho = ratio for evaluating plate buckling coefficient (k) k= N.A. If c/ho <= 1.0, then k = 2.2*(ho/c)^1.65, else k = 2.2*(ho/c) c/d = N.A. c/d = ratio for evaluating adjustment factor (f) of plate buckling model f= N.A. If c/d <= 1.0, then f = 2*(c/d), else f = 1+(c/d) Fbc = N.A. ksi Fbc = Min. of: (15,700*f*k*(tw/ho)^2 or 0.60*Fy)*(1-P/(0.60*Fy*Atg)) Rwb = N.A. kips Rwb = Fbc*Sn/e

(continued)

6 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab to Column Connection: Plate to Column Welding: (using AISC Table XIX, page 4-75) ew = 4.000 in. ew = D2+eb (eccentricity for weld design) L= 9.000 in. L = Hp kL = 0.375 in. kL = tp aL = 4.000 in. aL = ew a= 0.444 a = (aL)/L k= 0.000 k = 0 (for Special Case) C1 = 1.0 C1 = 1.0 for E70XX electrode C= 0.871 (interpolated from Table XIX) Pr = 16.00 kips Pr = SQRT(R^2+P^2) (total resultant load taken by 2 welds) q = 0.000 deg. q = 90-(ATAN(R/P)) (angle from vertical) Co = N.A. Co = "C" coefficient from AISC Table XIX C(max) = N.A. C(max) = 0.928*(2) A= N.A. A = C(max)/Co >= 1.0 Ca/Co = N.A. Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = N.A. Ca = (Ca/Co)*Co w(req'd) = 0.128 in. (size) w(req'd) =(Pr/((C or Ca)*C1*L))/16 Weld used >= weld req'd., O.K. w(recom'd) = 0.2813 in. w(recom'd) = ((0.40*Fyp*Hp*tp)/((C or Ca)*C1*L))/16 <= 0.75*tp w(min) = 0.1875 in. w(min) = Min. fillet weld size from AISC Table J2.4, page 5-67 Rwr = w*16*(C or Ca)*C1*L (w = actual weld size used) Rwr = 39.20 kips Rwv = Rwr*COSq (vertical) Rwv = 39.20 kips Rwv >= R, O.K. Rwa = Rwr*SINq (axial) Rwa = 0.00 kips Column Checks: Gross Shear Capacity of Flange at Plate: Av = 6.480 in.^2 Av = Hp*tfc Rv = 129.60 kips Rv = 0.40*Fyc*Av Gross Tension Capacity of Flange at Plate: At = 6.480 in.^2 At = Hp*tfc Rt = 191.44 kips Rt = (0.60*Fyc*At)*(1-(R/Rv)^2) Local Web Yielding: N= 9.000 Rwy = 168.11 Web Crippling: N= 9.000 Rwc = 100.57 (Criteria is assumed for beam near column end per AISC Eqn. K1-3) N = Hp Rwy = 0.66*Fyc*twc*(N+2.5*kc) (Criteria is for beam near column end per AISC Eqn. K1-5) N = Hp Rwc = 34*twc^2*(1+3*(N/d)*(twc/tfc)^1.5)*SQRT(Fyc*tfc/twc)

Rv >= R, O.K.

in. kips

in. kips

Comments:

7 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

AISC BEAM END CONNECTION (ASD)


Using Beam Tab (Single Plate) Bolted to Beam Web and Welded to Column Web Subjected to Shear and/or Axial Load Job Name: Subject: Job Number: Originator: Checker: Input Data: Beam and Column Data: Beam Size = Column Size = Beam Yield Stress, Fyb = Column Yield Stress, Fyc = Connection Loading: Beam End Reaction (Shear), R = Beam Axial Force, P =
tw=0.415 bf=10
ksi ksi

W16x26 W14x68 50 50

Face of Column Web tp=0.375 ED1=1.5 Hp=9 S1=3 S1=3

15.00 0.00

kips kips

ED2=1.5 S2=0 D2=3 D1=3 P=0 k R= 15 k s=0.5 Wp=4.5

Connection Data and Parameters: Beam Tab Height, Hp = 9.0000 Beam Tab Width, Wp = 4.5000 Beam Tab Thickness, tp = 0.3750 Beam Tab Yield Stress, Fyp = 36 Diameter of Bolts, db = 0.750 ASTM Bolt Desig. (A325 or A490) = A325 Bolt Type (N, X, or SC) = N Bolt Hole Type in Beam Tab = Short-Slot Total No. of Bolts in Beam Tab, Nb = 3 Number of Vertical Rows, Nr = 1 Dist. from Top/Beam to Bolts, D1 = 3.0000 Bolt Vertical Spacing, S1 = 3.0000 Vertical Edge Distance, ED1 = 1.5000 Dist. to 1st Row of Bolts, D2 = 3.0000 Bolt Horizontal Spacing, S2 = 0.0000 Horizontal Edge Distance, ED2 = 1.5000 Beam Setback Distance, s = 0.5000 Length of Flange Cope(s), c = 0.0000 Depth of Top Flange Cope, dc1 = 0.0000 Depth of Bottom Flange Cope, dc2 = 0.0000 Fillet Weld Size at Plate, w = 5/16 Member Properties: Beam: A= 7.68 d = 15.700 tw = 0.250 bf = 5.500 tf = 0.345 k = 0.7470

in. in. in. ksi in.

5/16 5/16

General Nomenclature
tw=0.25 tf=0.345 c=0 dc1=0

in. in. in. in. in. in. in. in. in. in. in.

d=15.7

bf=5.5 c=0

dc2=0

Beam and Cope Nomenclature

Max. Shear Capacity of Connection: R(max) = 16.42 kips A= d= tw = bf = tf = k= Column: 20.00 14.000 0.415 10.000 0.720 1.3100
in.^2 in. in. in. in. in. (continued)

8 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Results: General Parameters: Bolt and Material Data: dhy1 = 0.9375 dhx1 = 1.0000 dh2 = 0.8125 Ab = 0.4418 Fup = 58.0 Fub = 65.0 Fuc = 65.0

in. in. in. in.^2 ksi ksi ksi

dhy1 = db+3/16 (Short-Slot hole for 0.75 in. bolts in plate) dhx1 = db+1/4 (Short-Slot hole for 0.75 in. bolts in plate) dh2 = db+1/16 (Standard hole for 0.75 in. bolts in beam web) Ab = p*db^2/4 Fup = 58 for Fyp = 36 (for plate) Fub = 65 for Fyb = 50 (for beam) Fuc = 65 for Fyc = 50 (for column) (assuming "flexible" support provided at column web) (using AISC Table XI, page 4-62) n = Nb/Nr (number of bolts in a vertical row) b = S1 eb = Max. of: ABS(2*(Nb/Nr)/3-D2) or D2 (interpolated from Table XI) Pr = SQRT(R^2+P^2) (total resultant load taken by bolts) q = 90-(ATAN(R/P)) (angle from vertical) Co = "C" coefficient from AISC Table XI C(max) = n A = C(max)/Co >= 1.0 Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = (Ca/Co)*Co vb = Pr/(C or Ca) fv = vb/Ab Fv = Allow. shear stress from AISC Table J3.2, page 5-73 (for N bolts) Vb = Fv*Ab Rbr = Vb*(C or Ca) (resultant) Rbv = Rbr*COSq (vertical) Rbv >= R, O.K. Rba = Rbr*SINq (axial)

Beam Tab to Beam Connection: Bolt Shear (includes eccentricity): n= 3 bolts b= 3.000 in. eb = 3.000 in. C= 1.770 Pr = 15.00 kips q = 0.000 deg. Co = N.A. C(max) = N.A. A= N.A. Ca/Co = N.A. Ca = N.A. vb = 8.47 kips/bolt fv = 19.18 ksi Fv = 21.00 ksi Vb = 9.28 kips/bolt Rbr = 16.42 kips Rbv = 16.42 kips Rba = 0.00 kips

Beam Tab Checks: Bolt Bearing Capacity of Plate (for Vertical): C1 = 0 in. C1 = Spacing increment from AISC Table J3.4, page 5-76 C2 = 0 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 19.58 kips Rpe = (1.2*Fup*db*tp)*(Nr) (C2 is not applicable for ED1 >= 1.5*db) Rps = 39.15 kips Rps = (1.2*Fup*db*tp)*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 58.73 kips Rpv = Rpe+Rps <= (1.2*Fup*db*tp)*Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Plate (for Axial): C1 = N.A. in. C1 = Spacing increment (not applicable for all edge bolts) C2 = 0.13 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 58.73 kips Rpe = (1.2*Fup*db*tp)*(Nb/Nr) (C2 is not applicable for ED2 >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load Rpa = 54.89 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= (1.2*Fup*db*tp)*(Nb)*(1-(R/Rpv)^2)
(Ref.: "Comb. Shear & Tension Stress" by: S.C. Goel, AISC Journal, 3rd Qtr.-1986) (continued)

9 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Gross Shear Capacity of Plate: Avg = 3.375 in.^2 Rvg = 48.60 kips Net Shear Capacity of Plate: Avn = 2.320 ksi Rvn = 40.37 kips Gross Tension Capacity of Plate: Atg = 3.375 in.^2 Rtg = 65.96 kips Net Tension Capacity of Plate: Atn = 2.250 in.^2 Rtn = 56.24 kips

Avg = Hp*tp Rvg = 0.40*Fyp*Avg

Rvg >= R, O.K.

Avn = (Hp-(Nb/Nr)*dhy1)*tp Rvn = 0.30*Fup*Avn

Rvn >= R, O.K.

Atg = Hp*tp Rtg = (0.60*Fyp*Atg)*(1-(R/Rvg)^2)

Atn = Atg-(Nb/Nr*(dhy1+1/16)*tp) <= 0.85*Atg Rtn = (0.50*Fup*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyp*Atg)*(1-(R/Rvn)^2)

Block Shear ("L-shaped") Capacity of Plate: Av = 1.934 in.^2 Av = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp At = 0.375 in.^2 At = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp Rbs = 44.52 kips Rbs = 0.30*Fup*Av+0.50*Fup*At Rbs >= R, O.K. Tension Tear-Out ("L-shaped") Capacity of Plate: Av = 0.375 in.^2 Av = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.934 in.^2 At = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp Rto = 55.49 kips Rto = (0.30*Fup*Av+0.50*Fup*At)*(1-(R/Rbs)^2) Tension Tear-Out ("U-shaped") Capacity of Plate: Av = 0.750 in.^2 Av = 2*(ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.547 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dhy1)*tp Rto = 57.91 kips Rto = (0.30*Fup*Av+0.50*Fup*At) Gross Bending in Plate: e= 6.000 in. M= 90.00 in.-kips Sg = 5.06 in.^3 fbg = 17.78 ksi Fbg = 21.60 ksi Rbg = 18.23 kips Net Bending in Plate: e= 3.000 M= 45.00 Sn = 3.56 fbn = 12.63 Fbn = 21.60 Rbn = 25.65

e = D2+eb (eccentricity for plate bending at support) M = R*e (eccentric moment at face of support) Sg = tp*Hp^2/6 fbg = M/Sg Fbg = 0.60*Fyp Rbg = (Fbg*Sg/e)*(1-(P/Rtg)) Rbg >= R, O.K.

in. in.-kips in.^3 ksi ksi kips

e = eb (eccentricity for plate bending at holes) M = R*e (eccentric moment at face of support) Sn = tp*Hp^2/6-S1^2*(Nb/Nr)*((Nb/Nr)^2-1)*(tp*(dhy1+1/16))/(6*Hp) fbn = M/Sn Fbn = 0.60*Fyp Rbn = (Fbn*Sn/e)*(1-(P/Rtn)) Rbn >= R, O.K.
(continued)

10 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Axial Compression Capacity of Plate: Acg = 3.38 in.^2 Acg = Hp*tp Lc = 3.00 in. Lc = Max. of D2 or S2 K= 1.20 (assumed effective length factor for plate supported on one edge) r= 0.108 in. r = tp/(SQRT(12)) KL/r = 33.26 KL/r = K*Lc/r Cc = 126.10 Cc = SQRT(2*p^2*29000/Fyp) Fa = 19.71 ksi If KL/r <= Cc: Fa = --(1-(K*Lc/r )^2/(2*Cc^2))*Fyp/(5/3+3*(K*Lc/r)/(8*Cc)-(K*Lc/r)^3/(8*Cc^3)) --If K*L/r > Cc: Fa = 12*p^2*29000/(23*(K*Lc/r)^2) Rc = 66.51 kips Rc = Fa*Acg Beam Checks for Uncoped Flanges: Bolt Bearing Capacity of Beam Web (for Vertical): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = N.A. in. C2 = Edge distance increment (not applicable for uncoped beam) Rpe = 14.63 kips Rpe = 1.2*Fub*db*tw*(Nr) (for Nr edge bolts, edge dist., C2 are N.A.) Rps = 29.25 kips Rps = 1.2*Fub*db*tw*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 43.88 kips Rpv = Rpe+Rps <= 1.2*Fub*db*tw*(Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Beam Web (for Axial): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = 0 in. C2 = Edge distance increment (C2 = 0 for Standard holes in web) Rpe = 43.88 kips Rpe = 1.2*Fub*db*tw*(Nb/Nr) (C2 is not applicable for D2-s >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load) Rpa = 38.75 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= 1.2*Fub*db*tw*(Nb)*(1-(R/Rpv)^2) Gross Shear Capacity of Beam Web: ho = N.A in. ho = not applicable for uncoped beam Avg = 3.925 in.^2 Avg = d*tw Rvg = 78.50 kips Rvg = 0.40*Fyb*Avg Net Shear Capacity of Beam Web: Avn = 3.316 in.^2 Rvn = 64.65 kips Gross Tension Capacity of Beam: Atg = 7.680 in.^2 Rtg = 221.99 kips Net Tension Capacity of Beam: Atn = 6.528 in.^2 Rtn = 200.74 kips

Rvg >= R, O.K.

Avn = (d-Nb/Nr*dh2)*tw Rvn = 0.30*Fub*Avn <= 0.40*Fyb*Avg

Rvn >= R, O.K.

Atg = A Rtg = (0.60*Fyb*Atg)*(1-(R/Rvg)^2)

Atn = Atg-(Nb/Nr*(dh2+1/16))*tw <= 0.85*Atg Rtn = (0.50*Fub*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyb*Atg)*(1-(R/Rvn)^2)

(continued)

11 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Checks for Uncoped Flanges (continued): Block Shear ("L-shaped") Capacity of Beam Web: Av = N.A. in.^2 Av = not applicable for uncoped beam At = N.A. in.^2 At = not applicable for uncoped beam Rbs = N.A. kips Rbs = not applicable for uncoped beam Tension Tear-Out ("L-shaped") Capacity of Beam Web: Av = N.A. in.^2 Av = not applicable for uncoped beam At = N.A. in.^2 At = not applicable for uncoped beam Rto = N.A. kips Rto = not applicable for uncoped beam Tension Tear-Out ("U-shaped") Capacity of Beam Web: Av = 1.047 in.^2 Av = 2*((D2-s)+(Nr-1)*S2-((Nr-1)*dh2+dh2/2))*tw At = 1.094 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dh2)*tw Rto = 55.96 kips Rto = 0.30*Fub*Av+0.50*Fub*At Web Buckling (Flexure) Capacity Not Applicable for Uncoped Beam ho = N.A. in. ho = d-dc1 e= N.A. in. e = c+s yc = N.A. in. yc = (bf*tf^2/2+(ho-tf)*tw*(tf+(ho-tf)/2))/((ho-tf)*tw+bf*tf) In = N.A. in.^4 In=bf*tf^3/12+bf*tf*(yc-tf/2)^2+tw*(ho-tf)^3/12+(ho-tf)*tw*(tf+(ho-tf)/2-yc)^2 Sn = N.A. in.^3 Sn = In/(ho-yc) c/ho = N.A. c/ho = ratio for evaluating plate buckling coefficient (k) k= N.A. If c/ho <= 1.0, then k = 2.2*(ho/c)^1.65, else k = 2.2*(ho/c) c/d = N.A. c/d = ratio for evaluating adjustment factor (f) of plate buckling model f= N.A. If c/d <= 1.0, then f = 2*(c/d), else f = 1+(c/d) Fbc = N.A. ksi Fbc = Min. of: (15,700*f*k*(tw/ho)^2 or 0.60*Fy)*(1-P/(0.60*Fy*Atg)) Rwb = N.A. kips Rwb = Fbc*Sn/e

(continued)

12 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab to Column Connection: Plate to Column Welding: (using AISC Table XIX, page 4-75) ew = 6.000 in. ew = D2+eb (eccentricity for weld design) L= 9.000 in. L = Hp kL = 0.375 in. kL = tp aL = 6.000 in. aL = ew a= 0.667 a = (aL)/L k= 0.000 k = 0 (for Special Case) C1 = 1.0 C1 = 1.0 for E70XX electrode C= 0.614 (interpolated from Table XIX) Pr = 15.00 kips Pr = SQRT(R^2+P^2) (total resultant load taken by 2 welds) q = 0.000 deg. q = 90-(ATAN(R/P)) (angle from vertical) Co = N.A. Co = "C" coefficient from AISC Table XIX C(max) = N.A. C(max) = 0.928*(2) A= N.A. A = C(max)/Co >= 1.0 Ca/Co = N.A. Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = N.A. Ca = (Ca/Co)*Co w(req'd) = 0.170 in. (size) w(req'd) =(Pr/((C or Ca)*C1*L))/16 Weld used >= weld req'd., O.K. w(recom'd) = 0.2813 in. w(recom'd) = ((0.40*Fyp*Hp*tp)/((C or Ca)*C1*L))/16 <= 0.75*tp w(min) = 0.1875 in. w(min) = Min. fillet weld size from AISC Table J2.4, page 5-67 Rwr = w*16*(C or Ca)*C1*L (w = actual weld size used) Rwr = 27.63 kips Rwv = Rwr*COSq (vertical) Rwv = 27.63 kips Rwv >= R, O.K. Rwa = Rwr*SINq (axial) Rwa = 0.00 kips Column Checks: Gross Shear Capacity of Web at Plate: Av = 3.735 in.^2 Av = Hp*twc Rv = 74.70 kips Rv = 0.40*Fyc*Av Gross Tension Capacity of Web at Plate: At = 3.735 in.^2 At = Hp*twc Rt = 107.53 kips Rt = (0.60*Fyc*At)*(1-(R/Rv)^2)

Rv >= R, O.K.

Comments:

13 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

AISC BEAM END CONNECTION (ASD)


Using Beam Tab (Single Plate) Bolted to Beam Web and Welded to Girder Web Subjected to Shear and/or Axial Load Job Name: Subject: Job Number: Originator: Checker: Input Data: Beam and Girder Data: Beam Size = Girder Size = Beam Yield Stress, Fyb = Girder Yield Stress, Fyg = Connection Loading: Beam End Reaction (Shear), R = Beam Axial Force, P = W16x26 W24x55 50 50
Face of Girder Web tp=0.375 ED1=1.5 Hp=9 S1=3 S1=3 ED2=1.5 S2=0 D2=3 D1=3 P=0 k R= 15 k s=0.5 Wp=4.5

ksi ksi

15.00 0.00

kips kips

Connection Data and Parameters: Beam Tab Height, Hp = 9.0000 Beam Tab Width, Wp = 4.5000 Beam Tab Thickness, tp = 0.3750 Beam Tab Yield Stress, Fyp = 36 Diameter of Bolts, db = 0.750 ASTM Bolt Desig. (A325 or A490) = A325 Bolt Type (N, X, or SC) = N Bolt Hole Type in Beam Tab = Short-Slot Total No. of Bolts in Beam Tab, Nb = 3 Number of Vertical Rows, Nr = 1 Dist. from Top/Beam to Bolts, D1 = 3.0000 Bolt Vertical Spacing, S1 = 3.0000 Vertical Edge Distance, ED1 = 1.5000 Dist. to 1st Row of Bolts, D2 = 3.0000 Bolt Horizontal Spacing, S2 = 0.0000 Horizontal Edge Distance, ED2 = 1.5000 Beam Setback Distance, s = 0.5000 Length of Flange Cope(s), c = 4.0000 Depth of Top Flange Cope, dc1 = 1.5000 Depth of Bottom Flange Cope, dc2 = 0.0000 Fillet Weld Size at Beam Tab, w = 5/16 Member Properties: Beam: A= 7.68 d = 15.700 tw = 0.250 bf = 5.500 tf = 0.345 k = 0.7470

in. in. in. ksi in.

5/16 5/16

General Nomenclature
(Girder not shown for clarity)

tw=0.25 tf=0.345

c=4 dc1=1.5

d=15.7
in. in. in. in. in. in. in. in. in. in. in.

bf=5.5 c=0

dc2=0

Beam and Cope Nomenclature


(Girder not shown for clarity)

Max. Shear Capacity of Connection: R(max) = 16.42 kips A= d= tw = bf = tf = k= Girder: 16.30 23.600 0.395 7.010 0.505 1.1100
in.^2 in. in. in. in. in. (continued)

14 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Results: General Parameters: Bolt and Material Data: dhy1 = 0.9375 dhx1 = 1.0000 dh2 = 0.8125 Ab = 0.4418 Fup = 58.0 Fub = 65.0 Fug = 65.0

in. in. in. in.^2 ksi ksi ksi

dhy1 = db+3/16 (Short-Slot hole for 0.75 in. bolts in plate) dhx1 = db+1/4 (Short-Slot hole for 0.75 in. bolts in plate) dh2 = db+1/16 (Standard hole for 0.75 in. bolts in beam web) Ab = p*db^2/4 Fup = 58 for Fyp = 36 (for plate) Fub = 65 for Fyb = 50 (for beam) Fug = 65 for Fyg = 50 (for girder) (assuming "flexible" support provided at girder web) (using AISC Table XI, page 4-62) n = Nb/Nr (number of bolts in a vertical row) b = S1 eb = Max. of: ABS(2*(Nb/Nr)/3-D2) or D2 (interpolated from Table XI) Pr = SQRT(R^2+P^2) (total resultant load taken by bolts) q = 90-(ATAN(R/P)) (angle from vertical) Co = "C" coefficient from AISC Table XI C(max) = n A = C(max)/Co >= 1.0 Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = (Ca/Co)*Co vb = Pr/(C or Ca) fv = vb/Ab Fv = Allow. shear stress from AISC Table J3.2, page 5-73 (for N bolts) Vb = Fv*Ab Rbr = Vb*(C or Ca) (resultant) Rbv = Rbr*COSq (vertical) Rbv >= R, O.K. Rba = Rbr*SINq (axial)

Beam Tab to Beam Connection: Bolt Shear (includes eccentricity): n= 3 bolts b= 3.000 in. eb = 3.000 in. C= 1.770 Pr = 15.00 kips q = 0.000 deg. Co = N.A. C(max) = N.A. A= N.A. Ca/Co = N.A. Ca = N.A. vb = 8.47 kips/bolt fv = 19.18 ksi Fv = 21.00 ksi Vb = 9.28 kips/bolt Rbr = 16.42 kips Rbv = 16.42 kips Rba = 0.00 kips

Beam Tab Checks: Bolt Bearing Capacity of Plate (for Vertical): C1 = 0 in. C1 = Spacing increment from AISC Table J3.4, page 5-76 C2 = 0 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 19.58 kips Rpe = (1.2*Fup*db*tp)*(Nr) (C2 is not applicable for ED1 >= 1.5*db) Rps = 39.15 kips Rps = (1.2*Fup*db*tp)*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 58.73 kips Rpv = Rpe+Rps <= (1.2*Fup*db*tp)*Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Plate (for Axial): C1 = N.A. in. C1 = Spacing increment (not applicable for all edge bolts) C2 = 0.13 in. C2 = Edge distance increment from AISC Table J3.6, page 5-76 Rpe = 58.73 kips Rpe = (1.2*Fup*db*tp)*(Nb/Nr) (C2 is not applicable for ED2 >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load Rpa = 54.89 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= (1.2*Fup*db*tp)*(Nb)*(1-(R/Rpv)^2)
(Ref.: "Comb. Shear & Tension Stress" by: S.C. Goel, AISC Journal, 3rd Qtr.-1986) (continued)

15 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Gross Shear Capacity of Plate: Avg = 3.375 in.^2 Rvg = 48.60 kips Net Shear Capacity of Plate: Avn = 2.320 ksi Rvn = 40.37 kips Gross Tension Capacity of Plate: Atg = 3.375 in.^2 Rtg = 65.96 kips Net Tension Capacity of Plate: Atn = 2.250 in.^2 Rtn = 56.24 kips

Avg = Hp*tp Rvg = 0.40*Fyp*Avg

Rvg >= R, O.K.

Avn = (Hp-(Nb/Nr)*dhy1)*tp Rvn = 0.30*Fup*Avn

Rvn >= R, O.K.

Atg = Hp*tp Rtg = (0.60*Fyp*Atg)*(1-(R/Rvg)^2)

Atn = Atg-(Nb/Nr*(dhy1+1/16)*tp) <= 0.85*Atg Rtn = (0.50*Fup*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyp*Atg)*(1-(R/Rvn)^2)

Block Shear ("L-shaped") Capacity of Plate: Av = 1.934 in.^2 Av = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp At = 0.375 in.^2 At = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp Rbs = 44.52 kips Rbs = 0.30*Fup*Av+0.50*Fup*At Rbs >= R, O.K. Tension Tear-Out ("L-shaped") Capacity of Plate: Av = 0.375 in.^2 Av = (ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.934 in.^2 At = ((ED1+(Nb/Nr-1)*S1)-((Nb/Nr-1)*dhy1+dhy1/2))*tp Rto = 55.49 kips Rto = (0.30*Fup*Av+0.50*Fup*At)*(1-(R/Rbs)^2) Tension Tear-Out ("U-shaped") Capacity of Plate: Av = 0.750 in.^2 Av = 2*(ED2+(Nr-1)*S2-((Nr-1)*dhx1+dhx1/2))*tp At = 1.547 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dhy1)*tp Rto = 57.91 kips Rto = (0.30*Fup*Av+0.50*Fup*At) Gross Bending in Plate: e= 6.000 in. M= 90.00 in.-kips Sg = 5.06 in.^3 fbg = 17.78 ksi Fbg = 21.60 ksi Rbg = 18.23 kips Net Bending in Plate: e= 3.000 M= 45.00 Sn = 3.56 fbn = 12.63 Fbn = 21.60 Rbn = 25.65

e = D2+eb (eccentricity for plate bending at support) M = R*e (eccentric moment at face of support) Sg = tp*Hp^2/6 fbg = M/Sg Fbg = 0.60*Fyp Rbg = (Fbg*Sg/e)*(1-(P/Rtg)) Rbg >= R, O.K.

in. in.-kips in.^3 ksi ksi kips

e = eb (eccentricity for plate bending at holes) M = R*e (eccentric moment at face of support) Sn = tp*Hp^2/6-S1^2*(Nb/Nr)*((Nb/Nr)^2-1)*(tp*(dhy1+1/16))/(6*Hp) fbn = M/Sn Fbn = 0.60*Fyp Rbn = (Fbn*Sn/e)*(1-(P/Rtn)) Rbn >= R, O.K.
(continued)

16 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab Checks (continued): Axial Compression Capacity of Plate: Acg = 3.38 in.^2 Acg = Hp*tp Lc = 3.00 in. Lc = Max. of D2 or S2 K= 1.20 (assumed effective length factor for plate supported on one edge) r= 0.108 in. r = tp/(SQRT(12)) KL/r = 33.26 KL/r = K*Lc/r Cc = 126.10 Cc = SQRT(2*p^2*29000/Fyp) Fa = 19.71 ksi If KL/r <= Cc: Fa = --(1-(K*Lc/r )^2/(2*Cc^2))*Fyp/(5/3+3*(K*Lc/r)/(8*Cc)-(K*Lc/r)^3/(8*Cc^3)) --If K*L/r > Cc: Fa = 12*p^2*29000/(23*(K*Lc/r)^2) Rc = 66.51 kips Rc = Fa*Acg Beam Checks for Top Flange Coped Only: Bolt Bearing Capacity of Beam Web (for Vertical): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = 0 in. C2 = Edge distance increment (C2 = 0 for Standard holes in web) Rpe = 14.63 kips Rpe = 1.2*Fub*db*tw*(Nr) (C2 is not applicable for D1-dc1 >= 1.5*db) Rps = 29.25 kips Rps = 1.2*Fub*db*tw*(Nb-Nr) (C1 is not applicable for S1 >= 3*db) Rpv = 43.88 kips Rpv = Rpe+Rps <= 1.2*Fub*db*tw*(Nb) Rpv >= R, O.K. Bolt Bearing Capacity of Beam Web (for Axial): C1 = 0 in. C1 = Spacing increment (C1 = 0 for Standard holes in web) C2 = 0 in. C2 = Edge distance increment (C2 = 0 for Standard holes in web) Rpe = 43.88 kips Rpe = 1.2*Fub*db*tw*(Nb/Nr) (C2 is not applicable for D2-s >= 1.5*db) Rps = 0.00 kips Rps = not applicable, since all edge bolts for bearing due to axial load) Rpa = 38.75 kips Rpa = (Rpe+Rps)*(1-(R/Rpv)^2) <= 1.2*Fub*db*tw*(Nb)*(1-(R/Rpv)^2) Gross Shear Capacity of Beam Web for Top Flange Coped: ho = 14.200 in. ho = d-dc1 Avg = 3.550 in.^2 Avg = ho*tw Rvg = 71.00 kips Rvg = 0.40*Fyb*Avg Net Shear Capacity of Beam Web for Top Flange Coped: Avn = 2.941 in.^2 Avn = (ho-Nb/Nr*dh2)*tw Rvn = 57.34 kips Rvn = 0.3*Fub*Avn <= 0.40*Fyb*Avg Gross Tension Capacity of Beam for Top Flange Coped: Atg = 5.494 in.^2 Atg = A-(bf*tf+(dc1-tf)*tw) Rtg = 157.46 kips Rtg = (0.60*Fyb*Atg)*(1-(R/Rvg)^2) Net Tension Capacity of Beam for Top Flange Coped: Atn = 4.670 in.^2 Atn = Atg-(Nb/Nr*(dh2+1/16))*tw <= 0.85*Atg Rtn = 141.38 kips Rtn = (0.50*Fub*Atn)*(1-(R/Rvn)^2) <= (0.60*Fyb*Atg)*(1-(R/Rvn)^2)

Rvg >= R, O.K.

Rvn >= R, O.K.

(continued)

17 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Checks for Top Flange Coped Only (continued): Block Shear ("L-shaped") Capacity of Beam Web for Top Flange Coped: Av = 1.367 in.^2 Av = ((D1-dc1)+(Nb/Nr-1)*S1-((Nb/Nr-1)*dh2+dh2/2))*tw At = 0.523 in.^2 At = ((D2-s)+(Nr-1)*S2-((Nr-1)*dh2+dh2/2))*tw Rbs = 43.67 kips Rbs = 0.30*Fub*Av+0.50*Fub*At Rbs >= R, O.K. Tension Tear-Out ("L-shaped") Capacity of Beam Web for Top Flange Coped: Av = 0.523 in.^2 Av = ((D2-s)+(Nr-1)*S2-((Nr-1)*dh2+dh2/2))*tw At = 1.367 in.^2 At = ((D1-dc1)+(Nb/Nr-1)*S1-((Nb/Nr-1)*dh2+dh2/2))*tw Rto = 48.19 kips Rto = (0.30*Fub*Av+0.50*Fub*At)*(1-(R/Rbs)^2) Tension Tear-Out ("U-shaped") Capacity of Beam Web for Top Flange Coped: Av = 1.047 in.^2 Av = 2*((D2-s)+(Nr-1)*S2-((Nr-1)*dh2+dh2/2))*tw At = 1.094 in.^2 At = ((Nb/Nr-1)*S1-(Nb/Nr-1)*dh2)*tw Rto = 55.96 kips Rto = (0.30*Fub*Av+0.50*Fub*At) Web Buckling (Flexure) Capacity for Top Flange Coped: ho = 14.200 in. ho = d-dc1 e= 4.500 in. e = c+s yc = 4.760 in. yc = (bf*tf^2/2+(ho-tf)*tw*(tf+(ho-tf)/2))/((ho-tf)*tw+bf*tf) In = 117.23 in.^4 In=bf*tf^3/12+bf*tf*(yc-tf/2)^2+tw*(ho-tf)^3/12+(ho-tf)*tw*(tf+(ho-tf)/2-yc)^2 Sn = 12.42 in.^3 Sn = In/(ho-yc) c/ho = 0.282 c/ho = ratio for evaluating plate buckling coefficient (k) k = 17.795 If c/ho <= 1.0, then k = 2.2*(ho/c)^1.65, else k = 2.2*(ho/c) c/d = 0.255 c/d = ratio for evaluating adjustment factor (f) of plate buckling model f= 0.510 If c/d <= 1.0, then f = 2*(c/d), else f = 1+(c/d) Fbc = 30.00 ksi Fbc = Min. of: (15,700*f*k*(tw/ho)^2 or 0.60*Fy)*(1-P/(0.60*Fy*Atg)) Rwb = 82.78 kips Rwb = Fbc*Sn/e Rwb >= R, O.K.

(continued)

18 of 19

10/31/2012 7:13 AM

"BEAMTAB.xls" Program Version 1.3

Beam Tab to Girder Connection: Plate to Girder Welding: (using AISC Table XIX, page 4-75) ew = 6.000 in. ew = D2+eb (eccentricity for weld design) L= 9.000 in. L = Hp kL = 0.375 in. kL = tp aL = 6.000 in. aL = ew a= 0.667 a = (aL)/L k= 0.000 k = 0 (for Special Case) C1 = 1.0 C1 = 1.0 for E70XX electrode C= 0.614 (interpolated from Table XIX) Pr = 15.00 kips Pr = SQRT(R^2+P^2) (total resultant load taken by 2 welds) q = 0.000 deg. q = 90-(ATAN(R/P)) (angle from vertical) Co = N.A. Co = "C" coefficient from AISC Table XIX C(max) = N.A. C(max) = 0.928*(2) A= N.A. A = C(max)/Co >= 1.0 Ca/Co = N.A. Ca/Co = A/(SINq+A*COSq) >= 1.0 Ca = N.A. Ca = (Ca/Co)*Co w(req'd) = 0.170 in. (size) w(req'd) =(Pr/((C or Ca)*C1*L))/16 Weld used >= weld req'd., O.K. w(recom'd) = 0.2813 in. w(recom'd) = ((0.40*Fyp*Hp*tp)/((C or Ca)*C1*L))/16 <= 0.75*tp w(min) = 0.1875 in. w(min) = Min. fillet weld size from AISC Table J2.4, page 5-67 Rwr = w*16*(C or Ca)*C1*L (w = actual weld size used) Rwr = 27.63 kips Rwv = Rwr*COSq (vertical) Rwv = 27.63 kips Rwv >= R, O.K. Rwa = Rwr*SINq (axial) Rwa = 0.00 kips Girder Checks: Gross Shear Capacity of Web at Plate: Av = 3.555 in.^2 Av = Hp*twg Rv = 71.10 kips Rv = 0.40*Fyg*Av Gross Tension Capacity of Web at Plate: At = 3.555 in.^2 At = Hp*twg Rt = 101.90 kips Rt = (0.60*Fyg*At)*(1-(R/Rv)^2)

Rv >= R, O.K.

Comments:

19 of 19

10/31/2012 7:13 AM

Potrebbero piacerti anche