Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. In a 30 mm thick cylindrical shell, the longitudinal as well as circumferential joints are double welded butt welds with full penetration. Which of the following is true as regards the longitudinal and circumferential joints? They are of same category but different types. They are of same type but different categories. Both the category as well as type are same. Both the category as well as type are different. Vessel MAWP of existing vertical vessel will be affected for which of the following? a. If Vessel Part MAWP changes for any vessel part. b. If design pressure is reduced (other factors remaining same) c. Vessel height is changed by adding/deleting a shell course d. A and C A Shell with Inside dia = 2200 mm, and Corr. allow.= 5 mm is to be designed as per ASME Sec. VIII , Div.1. What will the value of R in design formula for shell thickness? 1100 mm 1105 mm 1095 mm 1110 mm In thickness formula for internal pressure for shell, term E refers to: Modules of Elasticity of material Thermal Expansion Joint efficiency of the weld None of above The hydrostatic pressure caused by 10 ft. of liquid column (sp. gr. = 1) will be: 10 psi 43.3 psi 4.33 psi None of the above 6. A new pressure vessel should be inspected to which of the following codes? a. API 510 , b. ASME Sec. 1, c. ASME Sec. VIII Div. 1, d. None of these 7. a. b. c. Code rules for testing vessels in service are detailed in: API 510 API 570 ASME Section VIII Div.1
a. b. c. d. 2.
3. a. b. c. d. 4. a. b. c. d. 5. a. b. c. d.
Question Bank for API 510 Exam Book Code: API510QB001 www.apiXams.blogspot.com Copyright apiXams
8. a. b. c. d.
9.
Identify category A joints from following: Longitudinal joints Circumferential joints, shell to shell Shell to hemispherical head joint a and c above
If all other conditions are remains same the design thickness of which dished end (Torispherical, Hemispherical, Ellipsoidal) will be maximum? a. Torispherical b. Hemispherical c. Ellipsoidal d. All will be same Any thickness-offset within the allowable tolerance shell be provided a minimum taper transition of: 3 to 1 min 4 to 1 min 3 to 2 min 1 to 2 min
10. a. b. c. d.
11.
ASME Sec VIII Div. 1 specifies different acceptance level for weld reinforcement, which of the following statements are true in your opinion? a. Permitted reinforcement for long. seems is higher than circ. seems b. Permitted reinforcement for long. seems is lower than circ. seems c. Permitted reinforcement for long. seems is same as circ. seems d. Permitted reinforcement does not depend on location of seems. Vessel MAWP for vertical vessel is measured at:
a. b. c. d. Top most point of vessel Bottom most point of vessel At the mid point between top & bottom None of above
12.
13. Which of the following statements is true? a. All defects are not discontinuities. b. All discontinuities are defects. c. Discontinuities are rejectable defects. d. Defects are rejectable discontinuities.
Question Bank for API 510 Exam Book Code: API510QB001 www.apiXams.blogspot.com Copyright apiXams
a. b. c. d. 18.
19. a. b. c. d. 20. a. b. c.
Question Bank for API 510 Exam Book Code: API510QB001 www.apiXams.blogspot.com Copyright apiXams
Question Bank for API 510 Exam Book Code: API510QB001 www.apiXams.blogspot.com Copyright apiXams
ANSWER KEY
Q. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
ANSWER B D B C C C A D A A B A D B C B B C B C
REFERENCE ASME VIII, UW 3 (a) ASME VIII, UG 98 (a) ASME VIII, UG 27 (a), UG -16 (e) ASME VIII, UG 27 (a) Body of Knowledge, 3 (a), Page 2 API 510, 3.2 API 510, 1.1 ASME VIII, UW 3 (a) (1) ASME VIII, UG 32, d, e, f ASME VIII, Fig. UW - 9 ASME VIII, UW - 35 ASME VIII, UG 98 (a) General Knowledge ASME VIII, Table UW - 12 ASME VIII, UW 32 (j) API 510, 3.2 ASME VIII, UW 12 (d) ASME VIII, UW 11 (a) - 7 ASME VIII, 98 (a) ASME VIII, UG 116 (e)
Question Bank for API 510 Exam Book Code: API510QB001 www.apiXams.blogspot.com Copyright apiXams